Inspiron 3593 Instrukcja serwisowa Model regulacji: P75F Typ regulacji: P75F013
Uwagi, przestrogi i ostrzeżenia UWAGA Napis UWAGA oznacza ważną wiadomość, która pomoże lepiej wykorzystać komputer. OSTRZEŻENIE Napis PRZESTROGA informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu lub utraty danych, i przedstawia sposoby uniknięcia problemu. PRZESTROGA Napis OSTRZEŻENIE informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu, obrażeń ciała lub śmierci. © 2019 Dell Inc. lub podmioty zależne. Wszelkie prawa zastrzeżone.
Spis treści 1 Serwisowanie komputera...............................................................................................................6 Instrukcje dotyczące bezpieczeństwa................................................................................................................................ 6 Przed przystąpieniem do serwisowania komputera.......................................................................................................... 6 Przed rozpoczęciem pracy..................
Instalowanie tabliczki dotykowej...................................................................................................................................41 Głośniki.................................................................................................................................................................................. 42 Wymontowywanie głośników....................................................................................................................................
Pobieranie sterownika mikroukładu................................................................................................................................... 78 Pobieranie sterownika czytnika kart pamięci................................................................................................................... 78 Pobieranie sterownika karty WiFi......................................................................................................................................
1 Serwisowanie komputera Instrukcje dotyczące bezpieczeństwa Aby uchronić komputer przed uszkodzeniem i zapewnić sobie bezpieczeństwo, należy przestrzegać następujących zaleceń dotyczących bezpieczeństwa. O ile nie wskazano inaczej, każda procedura opisana w tym dokumencie zakłada, że użytkownik zapoznał się z informacjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem.
UWAGA Jeśli używasz innego systemu operacyjnego, wyłącz urządzenie zgodnie z instrukcjami odpowiednimi dla tego systemu. 3. Odłącz komputer i wszystkie urządzenia peryferyjne od gniazdek elektrycznych. 4. Odłącz od komputera wszystkie urządzenia sieciowe i peryferyjne, np. klawiaturę, mysz, monitor itd. 5. Wyjmij z komputera wszystkie karty pamięci i dyski optyczne.
• • • • • korzystać z opasek bez przewodów. Należy pamiętać, że wewnętrzne przewody paska na nadgarstek są podatne na uszkodzenia podczas normalnego użytkowania. Należy je regularnie sprawdzać za pomocą testera, aby uniknąć przypadkowego uszkodzenia sprzętu przez wyładowania elektrostatyczne. Zaleca się testowanie paska na nadgarstek i przewodu łączącego co najmniej raz w tygodniu. Tester paska antystatycznego na nadgarstek — przewody wewnątrz paska są podatne na uszkodzenia.
3. Zainstaluj karty pamięci, dyski i wszelkie inne elementy wymontowane przed rozpoczęciem pracy. 4. Podłącz komputer i wszystkie urządzenia peryferyjne do gniazdek elektrycznych. 5. Włącz komputer.
2 Wymontowywanie i instalowanie komponentów Zalecane narzędzia Procedury przedstawione w tym dokumencie mogą wymagać użycia następujących narzędzi: • • • Wkrętak krzyżakowy nr 1 Wkrętak z płaskim grotem Rysik z tworzywa sztucznego Wykaz śrub UWAGA Przy wykręcaniu śrub z elementów zalecane jest, aby zanotować typ oraz liczbę śrub, a następnie umieścić je w pudełku na śruby. Umożliwia to przykręcenie właściwych śrub w odpowiedniej liczbie podczas ponownego instalowania elementu.
Element do czego mocowany Typ śruby Ilość Zawiasy Zestaw podparcia dłoni i klawiatury M2,5x5 5 Wsporniki zawiasu zestaw pokrywy wyświetlacza i anteny M2,5x4 8 Wsporniki zawiasu zestaw pokrywy wyświetlacza i anteny M2x2 2 Karta we/wy Zestaw podparcia dłoni i klawiatury M2x4 1 Wspornik napędu Napęd dysków optycznych optycznego (dotyczy tylko komputerów wyposażonych w napęd optyczny) M2x2 2 Płyta złącza napędu optycznego (tylko w komputerach wyposażonych w napęd optyczny) Zestaw podparc
1. Wykręć śrubę (M2x2) mocującą zestaw napędu optycznego do pokrywy dolnej. 2. Za pomocą śrubokrętu wypchnij napęd optyczny przez otwór, aby uwolnić zestaw napędu optycznego z wnęki. 3. Wysuń zestaw napędu dysków optycznych z wnęki. 4. Wykręć dwie śruby (M2x3) mocujące wspornik napędu optycznego do napędu optycznego. 5. Zdejmij wspornik z napędu optycznego. 6. Ostrożnie pociągnij osłonę napędu dysków optycznych, aby odłączyć ją od napędu.
postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera. Więcej informacji na temat postępowania zgodnego z zasadami bezpieczeństwa znajduje się na stronie dotyczącej przestrzegania przepisów pod adresem www.dell.com/regulatory_compliance. Procedura 1. UWAGA Dotyczy tylko komputerów wyposażonych w napęd optyczny. Dopasuj zaczepy na osłonie napędu dysków optycznych do szczelin w napędzie i zatrzaśnij osłonę. 2.
pokrywa dolna Wymontowywanie pokrywy dolnej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
4. Podważ pokrywę dolną, zaczynając od lewego górnego rogu podstawy komputera. 5. Zdejmij pokrywę dolną z zestawu podparcia dłoni i klawiatury. UWAGA Wykonaj poniższe czynności tylko w przypadku, gdy chcesz wymontować inne części z komputera. 6. Odklej taśmę mocującą kabel akumulatora do złącza i odłącz kabel akumulatora od płyty systemowej.
7. Naciśnij przycisk zasilania i przytrzymaj go przez pięć sekund, aby uziemić komputer i usunąć pozostałe ładunki elektryczne. Procedura w przypadku komputerów wyposażonych w napęd optyczny 1. Poluzuj trzy śruby mocujące pokrywę dolną. 2. Wykręć śrubę (M2x4) mocującą pokrywę dolną do zestawu podparcia dłoni i klawiatury. 3. Wykręć dwie śruby (M2x2) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 4. Wykręć sześć śrub (M2,5x7) mocujących pokrywę dolną do zestawu podparcia dłoni i klawiatury.
UWAGA Wykonaj poniższe czynności tylko w przypadku, gdy chcesz wymontować inne części z komputera. 7. Odklej taśmę mocującą kabel akumulatora do złącza i odłącz kabel akumulatora od płyty systemowej. 8. Odłącz kabel akumulatora od płyty systemowej. 9. Naciśnij przycisk zasilania i przytrzymaj go przez pięć sekund, aby uziemić komputer i usunąć pozostałe ładunki elektryczne.
2. Umieść pokrywę dolną na zestawie podparcia dłoni i klawiatury. 3. Zatrzaśnij pokrywę dolną na miejscu, rozpoczynając od gniazda zasilacza. OSTRZEŻENIE Aby zapobiec przypadkowemu uszkodzeniu gniazda zasilacza, nie należy dociskać pokrywy dolnej do gniazda zasilacza podczas zatrzaskiwania pokrywy na podstawie komputera. 4. Dokręć trzy śruby osadzone mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 5. Wkręć sześć śrub (M2,5x7) mocujących pokrywę dolną do zestawu podparcia dłoni i klawiatury.
Procedura w przypadku komputerów wyposażonych w napęd optyczny 1. Podłącz kabel akumulatora do płyty systemowej i przyklej taśmę mocującą kabel akumulatora do złącza na płycie systemowej, jeśli ma to zastosowanie. 2. Umieść pokrywę dolną na zestawie podparcia dłoni i klawiatury. 3. Zatrzaśnij pokrywę dolną na miejscu, rozpoczynając od gniazda zasilacza.
4. Wkręć sześć śrub (M2,5x7) mocujących pokrywę dolną do zestawu podparcia dłoni i klawiatury. 5. Wkręć dwie śruby (M2x2) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury (dotyczy tylko komputerów wyposażonych w napęd optyczny). 6. Wkręć śrubę (M2x4) mocującą pokrywę dolną do zestawu podparcia dłoni i klawiatury. 7. Dokręć trzy śruby osadzone mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. Po wykonaniu procedury Zainstaluj napęd optyczny (opcjonalnie).
informacji na temat postępowania zgodnego z zasadami bezpieczeństwa znajduje się na stronie dotyczącej przestrzegania przepisów pod adresem www.dell.com/regulatory_compliance. Środki ostrożności dotyczące akumulatora litowo-jonowego OSTRZEŻENIE • Podczas obsługi akumulatora litowo-jonowego zachowaj ostrożność. • Przed wyjęciem z systemu akumulator należy maksymalnie rozładować. Można to zrobić, odłączając zasilacz sieciowy od systemu i czekając na wyładowanie się akumulatora.
Instalowanie akumulatora UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
3. Podłącz kabel akumulatora do płyty systemowej. Po wykonaniu procedury 1. Zainstaluj pokrywę dolną. 2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
2. Ostrożnie rozciągnij palcami zatrzaski zabezpieczające znajdujące się na końcach każdego gniazda modułu pamięci, aż moduł odskoczy. 3. Wyjmij moduł pamięci z gniazda. Instalowanie modułów pamięci UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Po wykonaniu procedury 1. Zainstaluj pokrywę dolną. 2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). karta sieci bezprzewodowej Wymontowywanie karty sieci bezprzewodowej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
5. Przesuń i wyjmij kartę sieci bezprzewodowej z gniazda. Instalowanie karty sieci bezprzewodowej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Po wykonaniu procedury 1. Zainstaluj pokrywę dolną. 2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). płyta złącza napędu dysków optycznych Wymontowywanie płyty złącza napędu dysków optycznych UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Instalowanie płyty złącza napędu dysków optycznych UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Bateria pastylkowa Wymontowywanie baterii pastylkowej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Procedura Włóż baterię pastylkową do gniazda na płycie we/wy, biegunem dodatnim skierowanym do góry. Po wykonaniu procedury 1. Zainstaluj pokrywę dolną. 2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
6. Odłącz kabel wentylatora od płyty systemowej. 7. Wykręć trzy śruby (M2,5x5) mocujące wentylator do zestawu podparcia dłoni i klawiatury. 8. Wyjmij wentylator z zestawu podparcia dłoni i klawiatury. Instalowanie wentylatora UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Procedura 1. Dopasuj otwory na śruby wentylatora do otworów w zestawie podparcia dłoni i klawiatury. 2. Wkręć trzy śruby (M2,5x5) mocujące wentylator do zestawu podparcia dłoni i klawiatury. 3. Podłącz kabel wentylatora do złącza na płycie systemowej. 4. Umieść kabel wyświetlacza w prowadnicach na wentylatorze. 5. Podłącz kabel wyświetlacza do płyty systemowej i zamknij zatrzask, aby zamocować kabel. UWAGA Dalsze kroki dotyczą tylko komputerów wyposażonych w napęd optyczny. 6.
2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Dysk SSD / pamięć Intel Optane Wymontowywanie dysku SSD / pamięci Intel Optane Przed wymontowaniem pamięci Intel Optane z komputera należy ją wyłączyć. Więcej informacji na temat wyłączania pamięci Intel Optane można znaleźć w temacie Wyłączanie pamięci Intel Optane.
7. Wyjmij dysk SSD z osłony termicznej karty M.2 2230. Procedura wymontowywania napędu SSD M.2 2280 1. Poluzuj śrubę mocującą osłonę termiczną karty M.2 2280 do zestawu podparcia dłoni i klawiatury. 2. Wykręć śrubę (M2x3) mocującą osłonę termiczną karty M.2 2280 oraz dysk SSD do zestawu podparcia dłoni i klawiatury. 3. Przesuń i wyjmij osłonę termiczną karty M.2 2280 z gniazda w zestawie podparcia dłoni i klawiatury. 4. Unieś kartę SSD pod kątem i wyjmij ją z gniazda M.2 na płycie systemowej.
Instalowanie dysku SSD / pamięci Intel Optane Włącz urządzenie Intel Optane po jego zainstalowaniu. Więcej informacji na temat włączania pamięci Intel Optane zawiera sekcja Włączanie pamięci Intel Optane. UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Procedura instalowania napędu SSD M.2 2280 1. Dopasuj wycięcie na dysku SSD do wypustki w gnieździe M.2 i wsuń dysk SSD na miejsce. 2. Włóż wypustkę na osłonie termicznej karty M.2 2280 do szczeliny w zestawie podparcia dłoni i klawiatury. 3. Wkręć śrubę (M2x3) mocującą osłonę termiczną karty M.2 2280 oraz dysk SSD do zestawu podparcia dłoni i klawiatury. 4. Dokręć śrubę mocującą osłonę termiczną karty M.2 2280 do zestawu podparcia dłoni i klawiatury. Po wykonaniu procedury 1. Zainstaluj pokrywę dolną.
2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Dysk twardy Wymontowywanie dysku twardego Jeśli komputer korzysta z urządzenia pamięci masowej SATA z akceleracją Intel Optane, wyłącz funkcję Intel Optane przed wymontowaniem urządzenia pamięci masowej SATA. Więcej informacji na temat wyłączania funkcji Intel Optane zawiera rozdział Wyłączanie funkcji Intel Optane.
5. Wykręć cztery śruby (M3x3) mocujące wspornik dysku twardego do dysku twardego. 6. Wyjmij dysk twardy ze wspornika. Instalowanie dysku twardego Po zainstalowaniu pamięci masowej SATA włącz funkcję Intel Optane. Więcej informacji na temat włączania funkcji Intel Optane zawiera rozdział Włączanie funkcji Intel Optane.
3. Podłącz przejściówkę do zestawu dysku twardego. 4. Umieść zestaw dysku twardego w zestawie podparcia dłoni i klawiatury, dopasowując go do wypustek. 5. Wkręć cztery śruby (M2x3) mocujące zestaw dysku twardego do zestawu podparcia dłoni i klawiatury. 6. Podłącz kabel dysku twardego do płyty systemowej i zamknij zatrzask, aby zamocować kabel.
Po wykonaniu procedury 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Tabliczka dotykowa Wymontowywanie tabliczki dotykowej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
4. Delikatnie odklej taśmę mocującą tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 5. Wykręć cztery śruby (M2x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 6. Wysuń i wyjmij tabliczkę dotykową z zestawu podparcia dłoni i klawiatury.
2. Wkręć cztery śruby (M2x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 3. Przyklej taśmę mocującą tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel dysku twardego do złącza na płycie systemowej i zamknij zatrzask złącza, aby zamocować kabel. 5. Podłącz kabel tabliczki dotykowej do złącza na płycie systemowej i zamknij zatrzask złącza, aby zamocować kabel. 6.
sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera. Więcej informacji na temat postępowania zgodnego z zasadami bezpieczeństwa znajduje się na stronie dotyczącej przestrzegania przepisów pod adresem www.dell.com/regulatory_compliance. Przed wykonaniem procedury 1. Wymontuj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). 2.
Po wykonaniu procedury 1. Zainstaluj dysk SSD / pamięć Intel Optane. 2. Zainstaluj pokrywę dolną. 3. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Radiator Wymontowywanie radiatora UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Instalowanie radiatora UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Po wykonaniu procedury 1. Zainstaluj pokrywę dolną. 2. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Zestaw wyświetlacza Wymontowywanie zestawu wyświetlacza UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
6. Wykręć pięć śrub (M2,5x5) mocujących lewy i prawy zawias do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. UWAGA W przypadku komputerów bez napędu optycznego w lewym zawiasie znajduje się dodatkowa śruba. 7. Otwórz zawiasy. 8. Unieś zestaw podparcia dłoni i klawiatury pod kątem. 9. Przesuń i wyjmij zestaw podparcia dłoni i klawiatury z zestawu wyświetlacza. 10. Po wykonaniu wszystkich powyższych czynności pozostaje zestaw wyświetlacza.
Instalowanie zestawu wyświetlacza UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
3. Wciśnij zawiasy do płyty systemowej oraz zestawu podparcia dłoni i klawiatury, dopasowując je do wypustek. 4. Wkręć pięć śrub (M2,5x5) mocujących lewy i prawy zawias do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. UWAGA W przypadku komputerów bez napędu optycznego w lewym zawiasie znajduje się dodatkowa śruba. 5. Umieść kabel wyświetlacza w prowadnicach na wentylatorze oraz zestawie podparcia dłoni i klawiatury. 6.
UWAGA Dalsze kroki dotyczą tylko komputerów wyposażonych w napęd optyczny. 7. Naciśnij zatrzask, aby podłączyć kabel płyty złącza napędu dysków optycznych do napędu dysków optycznych. 8. Naciśnij zatrzask, aby podłączyć kabel płyty złącza napędu optycznego do płyty systemowej. Po wykonaniu procedury 1. Zainstaluj kartę sieci bezprzewodowej. 2. Zainstaluj pokrywę dolną. 3. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
3. Odłącz kabel gniazda zasilacza od płyty systemowej. 4. Zanotuj sposób poprowadzenia kabla gniazda zasilacza, a następnie wyjmij kabel z prowadnic w zestawie podparcia dłoni i klawiatury. 5. Wykręć śrubę (M2x2) mocującą gniazdo zasilacza do zestawu podparcia dłoni i klawiatury. 6. Wyjmij gniazdo zasilacza razem z kablem z zestawu podparcia dłoni i klawiatury.
Karta we/wy Wymontowanie płyty we/wy UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Instalowanie płyty we/wy UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
3. Zainstaluj pokrywę dolną. 4. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). Przycisk zasilania Ilustracja: wymontowywanie przełącznika zasilania UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Wymiana przycisku zasilania UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
UWAGA W komputerach bez napędu optycznego na prawym zawiasie znajduje się dodatkowa śruba, która mocuje prawy zawias do zestawu podparcia dłoni i klawiatury. Po wykonaniu procedury 1. Zainstaluj wentylator. 2. Zainstaluj pokrywę dolną. 3. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
7. Wymontuj wentylator. 8. Wymontuj radiator. Procedura 1. Odłącz kabel gniazda zasilacza od płyty systemowej. 2. Odłącz kabel głośnika od płyty systemowej. 3. Podnieś zatrzask i odłącz klawiaturę od płyty systemowej. 4. Otwórz zatrzask i odłącz kabel podświetlenia klawiatury od płyty systemowej. 5. Otwórz zatrzask i odłącz kabel tabliczki dotykowej od płyty systemowej. 6. Otwórz zatrzask złącza i odłącz kabel dysku twardego od płyty systemowej. 7.
16. Wykręć śrubę (M2x4) mocującą płytę systemową do zestawu podparcia dłoni i klawiatury. 17. Wyjmij płytę systemową z zestawu podparcia dłoni i klawiatury. Instalowanie płyty systemowej UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Procedura 1. Dopasuj otwór na śrubę w płycie systemowej do otworu w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M2x4) mocującą płytę systemową do zestawu podparcia dłoni i klawiatury. 3. Zamknij prawy zawias wyświetlacza. 4. Wkręć trzy śruby (M2,5x5) mocujące prawy zawias do płyty systemowej. 5. Wsuń kabel czytnika linii papilarnych w złącze na płycie systemowej i zamknij zatrzask, aby zamocować kabel. 6. Wsuń kabel karty I/O do złącza na płycie systemowej i zamknij zatrzask. 7.
14. Otwórz zatrzask i podłącz kabel wyświetlacza do płyty systemowej. 15. Wyrównaj kabel złącza napędu optycznego ze złączami na płycie systemowej oraz zestawie podparcia dłoni i klawiatury (opcjonalnie). 16. Wsuń kabel płyty złącza napędu optycznego do złącza w zestawie podparcia dłoni i klawiatury (opcjonalnie). 17. Wsuń kabel płyty złącza napędu optycznego do złącza na płycie systemowej (opcjonalnie). Po wykonaniu procedury 1. Zainstaluj radiator. 2. Zainstaluj wentylator. 3.
Przycisk zasilania z czytnikiem linii papilarnych Wymontowywanie przycisku zasilania z czytnikiem linii papilarnych UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Instalowanie przycisku zasilania z czytnikiem linii papilarnych UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Zestaw podparcia dłoni i klawiatury Wymontowywanie zestawu podparcia dłoni i klawiatury UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera.
Instalowanie zestawu podparcia dłoni i klawiatury UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Osłona wyświetlacza Wymontowywanie osłony wyświetlacza UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
Procedura UWAGA Ta procedura ma zastosowanie tylko w przypadku komputerów bez ekranu dotykowego. Dopasuj osłonę wyświetlacza do zestawu pokrywy wyświetlacza i anteny, a następnie delikatnie wciśnij osłonę na miejsce. Po wykonaniu procedury 1. Zainstaluj zestaw wyświetlacza. 2. Zainstaluj kartę sieci bezprzewodowej. 3. Zainstaluj pokrywę dolną. 4. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
1. Rysikiem z tworzywa sztucznego delikatnie podważ kamerę, aby ją uwolnić z zestawu pokrywy wyświetlacza i anteny. 2. Odłącz przewód kamery od modułu kamery. 3. Wyjmij moduł kamery z zestawu pokrywy wyświetlacza i anteny.
Po wykonaniu procedury 1. Zainstaluj osłonę wyświetlacza. 2. Zainstaluj zestaw wyświetlacza. 3. Zainstaluj kartę sieci bezprzewodowej. 4. Zainstaluj pokrywę dolną. 5. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
3. Zdejmij taśmę mocującą kabel wyświetlacza do tyłu panelu wyświetlacza. 4. Podnieś zatrzask i odłącz kabel wyświetlacza od złącza kabla panelu wyświetlacza. 5. Wyjmij panel wyświetlacza z zestawu pokrywy wyświetlacza i anteny.
3. Przyklej taśmę mocującą kabel wyświetlacza do tyłu panelu wyświetlacza. 4. Umieść panel wyświetlacza na zestawie pokrywy wyświetlacza i anteny. 5. Wkręć cztery śruby (M2x2) mocujące panel wyświetlacza do zestawu pokrywy wyświetlacza i anteny. Po wykonaniu procedury 1. Zainstaluj osłonę wyświetlacza. 2. Zainstaluj zestaw wyświetlacza. 3. Zainstaluj kartę sieci bezprzewodowej. 4. Zainstaluj pokrywę dolną. 5. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera. Więcej informacji na temat postępowania zgodnego z zasadami bezpieczeństwa znajduje się na stronie dotyczącej przestrzegania przepisów pod adresem www.dell.com/regulatory_compliance. Przed wykonaniem procedury 1. Wymontuj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny). 2.
Po wykonaniu procedury 1. Zainstaluj panel wyświetlacza. 2. Zainstaluj osłonę wyświetlacza. 3. Zainstaluj zestaw wyświetlacza. 4. Zainstaluj kartę sieci bezprzewodowej. 5. Zainstaluj pokrywę dolną. 6. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
1. Odłącz przewód kamery od modułu kamery. 2. Zanotuj sposób poprowadzenia kabla wyświetlacza i wyjmij kabel z prowadnic w zestawie pokrywy wyświetlacza i anteny. 3. Wyjmij kabel wyświetlacza z zestawu pokrywy wyświetlacza i anteny.
Po wykonaniu procedury 1. Zainstaluj zawiasy wyświetlacza. 2. Zainstaluj panel wyświetlacza. 3. Zainstaluj osłonę wyświetlacza. 4. Zainstaluj zestaw wyświetlacza. 5. Zainstaluj kartę sieci bezprzewodowej. 6. Zainstaluj pokrywę dolną. 7. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
Instalowanie zestawu pokrywy wyświetlacza i anteny UWAGA Przed przystąpieniem do wykonywania czynności wymagających otwarcia obudowy komputera należy zapoznać się z instrukcjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem i wykonać procedurę przedstawioną w sekcji na temat czynności przed otwarciem obudowy komputera. Po zakończeniu pracy wewnątrz komputera należy postępować zgodnie z instrukcjami w sekcji na temat czynności po zakończeniu pracy wewnątrz komputera.
4. Zainstaluj kamerę. 5. Zainstaluj osłonę wyświetlacza. 6. Zainstaluj zestaw wyświetlacza. 7. Zainstaluj kartę sieci bezprzewodowej. 8. Zainstaluj pokrywę dolną. 9. Zainstaluj napęd optyczny (dotyczy tylko komputerów wyposażonych w napęd optyczny).
3 Sterowniki urządzeń Pobieranie sterownika karty dźwiękowej 1. Włącz komputer. 2. Przejdź do strony internetowej www.dell.com/support. 3. Wpisz znacznik serwisowy komputera i kliknij opcję Submit (Prześlij). UWAGA Jeśli nie masz znacznika serwisowego, skorzystaj z funkcji automatycznego wykrywania znacznika albo ręcznie wyszukaj model swojego komputera. 4. Kliknij pozycję Drivers & downloads (Sterowniki i pliki do pobrania). 5. Kliknij przycisk Detect Drivers (Wykryj sterowniki). 6.
11. Jeśli pojawi się monit funkcji User Account Control (Kontrola konta użytkownika), wyraź zgodę na wprowadzanie zmian w systemie. 12. Aplikacja zainstaluje wszystkie wykryte sterowniki i aktualizacje. UWAGA Nie wszystkie pliki mogą być instalowane automatycznie. Przejrzyj podsumowanie instalacji, aby sprawdzić, czy jest wymagana instalacja ręczna. 13. Aby ręcznie pobrać i zainstalować sterownik, kliknij opcję Category (Kategoria). 14. Kliknij pozycję Network (Sieć) na liście rozwijanej. 15.
8. Kliknij opcję View Drivers for My System (Wyświetl sterowniki do mojego systemu). 9. Kliknij przycisk Download and Install (Pobierz i zainstaluj), aby zainstalować wszystkie aktualizacje sterowników wykryte dla swojego komputera. 10. Wybierz miejsce, w którym mają zostać zapisane pliki. 11. Jeśli pojawi się monit funkcji User Account Control (Kontrola konta użytkownika), wyraź zgodę na wprowadzanie zmian w systemie. 12. Aplikacja zainstaluje wszystkie wykryte sterowniki i aktualizacje.
6. Przeczytaj i zaakceptuj warunki korzystania z narzędzia SupportAssist, po czym kliknij przycisk Continue (Kontynuuj). 7. W razie potrzeby komputer zacznie pobieranie i instalację narzędzia SupportAssist. UWAGA Zapoznaj się z wyświetlanymi na ekranie instrukcjami dotyczącymi konkretnej przeglądarki. 8. Kliknij opcję View Drivers for My System (Wyświetl sterowniki do mojego systemu). 9.
4 Program konfiguracji systemu UWAGA Zależnie od komputera oraz zainstalowanych w nim urządzeń wymienione w tej sekcji pozycje mogą, ale nie muszą, pojawiać się na ekranie. Program konfiguracji systemu OSTRZEŻENIE Ustawienia konfiguracji systemu BIOS powinni zmieniać tylko doświadczeni użytkownicy. Niektóre zmiany mogą spowodować nieprawidłową pracę komputera.
Boot Sequence Opcja Boot Sequence umożliwia pominięcie kolejności urządzeń startowych zdefiniowanej w programie konfiguracji systemu i uruchomienie komputera z określonego urządzenia (na przykład z napędu dysków optycznych lub z dysku twardego). Po wyświetleniu logo Dell, kiedy komputer wykonuje automatyczny test diagnostyczny (POST), dostępne są następujące funkcje: • • Dostęp do konfiguracji systemu: naciśnij klawisz F2. Wyświetlenie menu jednorazowej opcji uruchamiania: naciśnij klawisz F12.
5 Rozwiązywanie problemów Program diagnostyczny ePSA (Enhanced Pre-Boot System Assessment) Test diagnostyczny ePSA obejmuje pełną kontrolę elementów sprzętowych. Test ePSA jest wbudowany w systemie BIOS i uruchamiany wewnętrznie przez system BIOS.
Na przykład kontrolka stanu zasilania i stanu akumulatora miga dwa razy światłem bursztynowym, a potem następuje pauza, a następnie światłem białym trzy razy, a potem następuje pauza. Sekwencja 2,3 jest wykonywana do chwili wyłączenia komputera. Oznacza ona brak pamięci lub pamięci RAM. Poniższa tabela przedstawia różne sekwencje lampek stanu zasilania i akumulatora oraz powiązane problemy. Tabela 3.
3. Kliknij pozycję Product Support (Wsparcie dla produktu), wprowadź znacznik serwisowy komputera, a następnie kliknij przycisk Submit (Prześlij). UWAGA Jeśli nie masz znacznika serwisowego, skorzystaj z funkcji automatycznego wykrywania znacznika albo ręcznie wyszukaj model swojego komputera. 4. Kliknij pozycję Drivers & downloads (Sterowniki i pliki do pobrania) > Find it myself (Znajdę samodzielnie). 5. Wybierz system operacyjny zainstalowany na komputerze. 6. Przewiń stronę w dół i rozwiń pozycję BIOS.
8. Zostanie wyświetlone okno narzędzia aktualizacyjnego systemu BIOS. Postępuj zgodnie z instrukcjami wyświetlanymi na ekranie, aby ukończyć aktualizację systemu BIOS. Wyłączanie i włączanie karty Wi-Fi Jeśli komputer nie jest w stanie uzyskać dostępu do Internetu ze względu na problemy z łącznością Wi-Fi, można wyłączyć i włączyć kartę Wi-Fi.
6 Uzyskiwanie pomocy i kontakt z firmą Dell Narzędzia pomocy technicznej do samodzielnego wykorzystania Aby uzyskać informacje i pomoc dotyczącą korzystania z produktów i usług firmy Dell, można skorzystać z następujących zasobów internetowych: Tabela 4. Narzędzia pomocy technicznej do samodzielnego wykorzystania Narzędzia pomocy technicznej do samodzielnego wykorzystania Lokalizacja zasobu Informacje o produktach i usługach firmy Dell www.dell.