Inspiron 17/17R 소유자 매뉴얼 컴퓨터 모델: Inspiron 3721/5721 규정 모델: P17E 규정 유형: P17E001
참고, 주의 및 경고 참고: 주는 컴퓨터의 활용도를 높이는 데 도움이 되는 중요한 정보입니다. 주의: 주의는 지침을 준수하지 않을 경우 하드웨어의 손상 또는 데이터 유실 위 험이 있음을 알려줍니다. 경고: 경고는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. ____________________ © 2012 Dell Inc. 본 설명서에 사용된 상표: Dell™, DELL 로고 및 Inspiron™은 Dell Inc.의 상표입니다. Microsoft®, Windows® 및 Windows 시작 단추 로고는 미국 및/또는 기타 국가/지역에서 Microsoft Corporation 의 상표 또는 등록 상표입니다. Bluetooth®는 Bluetooth SIG, Inc. 소유의 등록 상표이며 라이센스 계약에 따라 Dell에서 사용됩니다. 2012 - 12 Rev.
차례 시작하기 전에 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 컴퓨터 및 연결된 장치 끄기 안전 지침 . . . . . . . . . . . . 권장 도구 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 10 10 컴퓨터 내부에서 작업한 후 . . . . . . . . . . . . . . . . . . . 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 전지 분리 . 절차 전지 장착 . 절차 . . . . . . . . . . . . . . . . . . . . . . . .
메모리 모듈 분리 . 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 메모리 모듈 장착 . 절차 . . . . 후행 조건 . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 하드 드라이브 제거 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O 보드 분리 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 37 I/O 보드 장착 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 38 절차 . . . . 후행 조건 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 시스템 보드 분리 . 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . .
스피커 분리 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 선행 조건 . 절차 . . . . 스피커 장착 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 절차 . . . . 후행 조건 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 디스플레이 조립품 분리 . 선행 조건 . 절차 . . . . 절차 . . . . 후행 조건 . 57 . . . . . . . . .
카메라 모듈 분리 . 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 71 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 카메라 모듈 장착 . 절차 . . . . 후행 조건 . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 전원 어댑터 포트 분리 . 선행 조건 . 절차 . . . . . . . . . . . . . . . . . . . . . . . . .
| 차례
시작하기 전에 컴퓨터 및 연결된 장치 끄기 주의: 데이타 손실을 방지하려면 컴퓨터를 끄기 전에 열린 파일을 모두 저장한 후 닫고 열린 프로그램을 모두 종료하십시오. 1 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중의 프로그램을 모두 종료합니다. 2 컴퓨터를 종료하십시오. Windows 8: a 마우스 포인터를 화면의 오른쪽 상단 모서리 또는 오른쪽 하단 모서리에 놓아 장식 (Charms) 사이드바를 엽니다. b 장식(Charms) 사이드바에서 설정→ 전원→ 종료을 클릭합니다. Windows 7: 시작 을 클릭하고 종료를 클릭합니다. Microsoft Windows가 종료되고 컴퓨터가 꺼집니다. 참고: 다른 운영 체제를 사용하는 경우 해당 운영 체제의 설명서에서 종료 지침을 참조하십시오. 3 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리합니다. 4 컴퓨터에서 전화선, 네트워크 케이블 및 연결된 장치를 분리합니다.
안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보십시 오. 자 세 한 안 전 모 범 사 례 정 보 는 Regulatory Compliance(규 정 준 수) 홈 페 이 지 (dell.com/regulatory_compliance)를 참조하십시오. 경고: 컴퓨터 덮개 및 패널을 열기 전에 전원을 모두 분리합니다. 컴퓨터 내부에서 작업 한 후 전원에 연결하기 전에 덮개, 패널 및 나사를 모두 장착합니다. 주의: 컴퓨터의 손상을 방지하려면 작업 표면이 평평하고 깨끗한지 확인합니다. 주의: 구성요소 및 카드의 손상을 방지하려면 구성요소 및 카드를 잡을 때 핀이나 단자 를 잡지 말고 모서리를 잡습니다. 주의: 숙련된 서비스 기술자만 컴퓨터 덮개를 분리하고 컴퓨터 내부의 구성요소에 액 세스할 수 있습니다.
컴퓨터 내부에서 작업한 후 교체 절차를 완료한 후 다음을 확인합니다. • 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사가 없는지 확인합니다. • 컴퓨터에서 작업하기 전에 분리한 외부 장치, 케이블, 카드 및 기타 부품을 모두 연결합 니다. • 컴퓨터 및 접속한 모든 장치를 전원 콘센트에 연결합니다. 주의: 컴퓨터의 전원을 켜기 전에 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사 가 없는지 확인합니다. 이렇게 하지 않으면 컴퓨터가 손상될 수 있습니다.
전지 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 디스플레이를 닫고 컴퓨터를 뒤집어 놓습니다. 2 전지 래치를 잠금 해제 위치로 밉니다. 전지 잠금이 해제될 때 딸깍 소리가 납니다. 3 전지를 들어 올려 컴퓨터 베이스에서 분리합니다.
전지 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 전지 베이의 슬롯에 전지의 탭을 맞추고 전지를 제자리에 끼웁니다.
광학 드라이브 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 절차 1 광학 드라이브 조립품을 컴퓨터 베이스에 고정하는 나사를 분리합니다. 2 손가락 끝으로 광학 드라이브 조립품을 밀어 광학 드라이브 베이에서 꺼냅니다.
3 광학 드라이브 조립품에 광학 드라이브 브래킷을 고정하는 나사를 제거하고 광학 드라 이브 브래킷을 분리합니다. 4 광학 드라이브 베젤을 조심스럽게 당겨서 광학 드라이브리에서 분리합니다.
광학 드라이브 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 광학 드라이브 베젤의 탭을 광학 드라이브의 슬롯에 맞추고 광학 드라이브 베젤을 제자 리에 끼워 넣습니다. 2 광학 드라이브 브래킷의 나사 구멍을 광학 드라이브 조립품의 나사 구멍에 맞추고 광학 드라이브 브래킷을 광학 드라이브 조립품에 고정시키는 나사를 장착합니다. 3 광학 드라이브 조립품을 광학 드라이브 베이로 밀어 넣고 광학 드라이브 브래킷의 나사 구멍이 컴퓨터 베이스의 나사 구멍에 맞춰지는지 확인합니다.
키보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 절차 1 디스플레이를 완전히 엽니다. 2 플라스틱 스크라이브를 사용하여 손목 받침대의 탭에서 키보드를 들어 올립니다.
3 키보드를 뒤집어 손목 받침대 위에 놓습니다. 4 커넥터 래치를 들어 올리고 키보드 케이블 커넥터에서 키보드 케이블을 분리합니다. 5 손목 받침대에서 키보드를 들어 꺼냅니다.
키보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 키보드 케이블을 키보드 케이블 커넥터에 밀어 넣고 커넥터 래치를 눌러 케이블을 고정 합니다. 2 손목 받침대의 슬롯에 키보드 하단에 있는 탭을 밀어 넣고 키보드를 손목 받침대에 적 절하게 놓습니다. 3 키보드의 모서리를 조심스럽게 눌러 키보드를 손목 받침대의 탭 아래에 고정합니다. 4 컴퓨터 베이스에 키보드를 고정하는 나사를 끼웁니다. 후행 조건 전지를 장착합니다. 13페이지의 "전지 장착"를 참조하십시오.
베이스 덮개 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 절차 1 베이스 덮개를 컴퓨터 본체에 고정하는 조임 나사를 풉니다. 2 손가락 끝으로 베이스 덮개를 들어 올려 컴퓨터 베이스의 슬롯에서 빼냅니다.
베이스 덮개 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 베이스 덮개의 탭을 컴퓨터 베이스의 슬롯에 밀어 넣고 베이스 덮개를 제자리에 끼웁니다. 2 베이스 덮개를 컴퓨터 본체에 고정하는 조임 나사를 조입니다. 후행 조건 전지를 장착합니다. 13페이지의 "전지 장착"를 참조하십시오.
메모리 모듈 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 절차 1 메모리 모듈이 튀어 나올 때까지 메모리 모듈 커넥터의 양쪽 끝에 있는 고정 클립을 손 끝으로 조심스럽게 벌립니다. 2 메모리 모듈 커넥터에서 메모리 모듈을 분리합니다.
메모리 모듈 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 메모리 모듈의 노치를 메모리 모듈 커넥터의 탭에 맞춥니다. 2 메모리 모듈을 45도 각도로 커넥터에 단단히 밀어 넣고 딸깍 소리가 나면서 제자리에 고정될 때까지 메모리 모듈을 아래로 누릅니다. 참고: 소리가 나지 않으면 메모리 모듈을 분리했다가 다시 설치합니다. 후행 조건 1 베이스 덮개를 장착합니다. 21페이지의 "베이스 덮개 장착"를 참조하십시오. 2 전지를 장착합니다. 13페이지의 "전지 장착"를 참조하십시오.
하드 드라이브 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 주의: 데이터 손실 위험이 있으므로 컴퓨터가 켜져 있거나 절전 모드인 상태에서 하드 드라이브를 분리하지 마십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오.
절차 1 하드 드라이브 조립품을 컴퓨터 베이스에 고정시키는 나사를 분리합니다. 2 당김 탭을 사용하여 하드 드라이브 조립품을 컴퓨터 한쪽으로 밀어서 시스템 보드에서 하드 드라이브 조립품을 분리합니다. 3 당김 탭을 사용하여 하드 드라이브 조립품을 들어 올려 컴퓨터 베이스에서 분리합니다.
4 하드 드라이브 브래킷을 하드 드라이브에 고정하는 나사를 분리합니다. 5 당김 탭을 사용하여 하드 드라이브 브래킷을 하드 드라이브 밖으로 들어 올립니다.
하드 드라이브 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 절차 1 하드 드라이브 브래킷의 나사 구멍을 하드 드라이브의 나사 구멍에 맞춥니다. 2 하드 드라이브 브래킷을 하드 드라이브에 고정하는 나사를 장착합니다. 3 하드 드라이브 어셈블리를 하드 드라이브 베이에 놓습니다. 4 하드 드라이브 조립품을 커넥터 쪽으로 밀어서 시스템 보드에 하드 드라이브 조립품을 연결합니다. 5 하드 드라이브 조립품을 컴퓨터 베이스에 고정시키는 나사를 끼웁니다.
코인 셀 전지 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 주의: 코인 셀 전지를 제거하면 BIOS 설정이 기본값으로 재설정됩니다. 코인 셀 전지를 분리하기 전에 BIOS 설정을 기록하는 것이 좋습니다. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 절차 플라스틱 스크라이브를 사용하여 조심스럽게 시스템 보드의 전지 소켓에서 코인 셀 전지를 꺼냅니다.
코인 셀 전지 교체하기 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 경고: 전지를 잘못 설치하면 폭발할 위험이 있습니다. 동일하거나 동등한 유형의 전지 로만 교체하십시오. 사용한 전지는 제조업체의 지침에 따라 처리하십시오. 절차 양극 방향이 위로 향하도록 코인 셀 전지를 시스템 보드의 전지 소켓에 끼워 넣습니다. 후행 조건 1 베이스 덮개를 장착합니다. 21페이지의 "베이스 덮개 장착"를 참조하십시오. 2 전지를 장착합니다. 13페이지의 "전지 장착"를 참조하십시오.
손목 받침대 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 3 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 절차 1 손목 받침대를 컴퓨터 베이스에 고정하는 나사를 제거합니다.
2 컴퓨터를 뒤집어 놓고 디스플레이를 완전히 열어 놓습니다. 3 커넥터 래치를 들어 올리고 당김 탭을 사용하여 터치패드 케이블과 전원 버튼 케이블을 시스템 보드에서 분리합니다.
4 손목 받침대를 컴퓨터 베이스에 고정시키는 나사를 제거합니다. 5 플라스틱 스크라이브를 사용하여 손목 받침대의 탭을 부드럽게 들어 올려 컴퓨터 베이 스의 슬롯에서 분리합니다. 주의: 디스플레이 조립품이 손상되지 않도록 조심스럽게 디스플레이 조립품에서 손목 받침대를 분리합니다. 6 손목 받침대를 들어 올려 컴퓨터 베이스에서 분리합니다.
손목 받침대 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 컴퓨터 베이스에 손목 받침대를 정렬합니다. 2 손목 받침대 가장자리를 아래로 눌러 제자리에 고정합니다. 3 손목 받침대를 컴퓨터 베이스에 고정시키는 나사를 끼웁니다. 4 터치패드 케이블 및 전원 버튼 케이블을 시스템 보드 커넥터에 밀어 넣고 커넥터 래치 를 눌러 케이블을 고정시킵니다. 5 디스플레이를 닫고 컴퓨터를 뒤집어 놓습니다. 6 손목 받침대를 컴퓨터 베이스에 고정시키는 나사를 끼웁니다. 후행 조건 1 키보드를 장착합니다.
무선 미니 카드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 3 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 4 손목 받침대를 분리합니다. 30페이지의 "손목 받침대 분리"를 참조하십시오. 절차 1 무선 미니 카드에서 안테나 케이블을 분리합니다. 2 무선 미니 카드를 시스템 보드에 고정하는 나사를 분리합니다.
3 무선 미니 카드를 밀어서 미니 카드 커넥터 밖으로 빼냅니다.
무선 미니 카드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 주의: 무선 미니 카드가 손상될 수 있으므로 무선 미니 카드 아래 케이블이 놓이지 않도 록 합니다. 1 무선 미니 카드의 노치를 미니 카드 커넥터의 탭에 맞춥니다. 2 무선 미니 카드를 45도 각도로 미니 카드 커넥터에 삽입합니다. 3 무선 미니 카드의 다른쪽 끝을 아래로 누르고 미니 카드를 시스템 보드 커넥터에 고정 하는 나사를 장착합니다. 4 무선 미니 카드에 안테나 케이블을 연결합니다. 다음 표에 컴퓨터에서 지원되는 무선 미니 카드의 안테나 케이블 색상표가 나옵니다.
I/O 보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 3 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 4 손목 받침대를 분리합니다. 30페이지의 "손목 받침대 분리"를 참조하십시오. 절차 1 I/O 보드를 컴퓨터 베이스에 고정하는 나사를 분리합니다. 2 커넥터 래치를 들어 올리고 당김 탭을 사용하여 시스템 보드에서 I/O 보드 케이블을 분 리합니다.
I/O 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 컴퓨터 베이스의 맞춤 포스트를 사용하여 I/O 보드를 제자리에 놓습니다. 2 I/O 보드를 컴퓨터 베이스에 고정하는 나사를 장착합니다. 3 컴퓨터 베이스에 I/O 보드 케이블을 부착합니다. 4 I/O 보드 케이블을 I/O 보드 케이블 커넥터로 밀어 넣고 커넥터 래치를 눌러 케이블을 고정합니다. 후행 조건 1 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 2 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오.
시스템 보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 참고: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 시스템 설정에서 서비스 태그를 입력해야 합니다. 참고: 시스템 보드에서 케이블을 분리하기 전에 커넥터의 위치를 기록하여 시스템 보 드를 교체한 후에 정확하게 다시 연결할 수 있도록 합니다. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 베이스 덮개를 분리합니다.
절차 1 시스템 보드에서 전원 어댑터 포트 케이블과 스피커 케이블을 분리합니다. 2 시스템 보드에서 마일라 슬리브를 벗겨냅니다.
3 시스템 보드에 디스플레이 케이블을 고정하는 테이프를 벗겨낸 후, 시스템 보드에서 디 스플레이 케이블을 분리합니다. 4 커넥터 래치를 들어 올리고 당김 탭을 사용하여 시스템 보드에서 I/O 보드 케이블을 분 리합니다.
5 시스템 보드를 컴퓨터 베이스에 고정시키는 나사를 분리합니다. 6 시스템 보드를 일정한 각도로 들어 올리고 컴퓨터 베이스의 슬롯에서 시스템 보드 포트 를 분리합니다. 7 시스템 보드 조립품을 들어 올려 컴퓨터 베이스에서 분리합니다. 8 하드 드라이브 인터포저 보드를 분리합니다. 51페이지의 "하드 드라이브 인터포저 보 드 분리"을 참조하십시오. 2 1 1 9 나사(5개) 2 시스템 보드 시스템 보드를 뒤집어 놓습니다. 10 팬을 분리합니다. 45페이지의 "팬 분리"를 참조하십시오. 11 냉각 조립품을 분리합니다. 48페이지의 "냉각 조립품 분리"를 참조하십시오.
시스템 보드 교체 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 참고: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 시스템 설정에서 서비스 태그를 입력해야 합니다. 절차 1 냉각 조립품을 장착합니다. 50페이지의 "냉각 조립품 장착"를 참조하십시오. 2 팬을 장착합니다. 47페이지의 "팬 장착"를 참조하십시오. 3 시스템 보드를 뒤집어 놓습니다. 4 하드 드라이브 인터포저 보드를 장착합니다. 53페이지의 "하드 드라이브 인터포저 보 드 장착"를 참조하십시오.
후행 조건 1 무선 미니 카드를 장착합니다. 36페이지의 "무선 미니 카드 장착"를 참조하십시오. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오. 4 27페이지의 "하드 드라이브 장착"에 설명된 3단계에서 5단계까지의 지침을 따릅니다. 5 코인 셀 전지를 끼웁니다. 29페이지의 "코인 셀 전지 교체하기"를 참조하십시오. 6 메모리 모듈을 장착합니다. 23페이지의 "메모리 모듈 장착"를 참조하십시오. 7 베이스 덮개를 장착합니다. 21페이지의 "베이스 덮개 장착"를 참조하십시오. 8 16페이지의 "광학 드라이브 장착"에 설명된 3단계에서 4단계까지의 지침을 따릅니다. 9 전지를 장착합니다. 13페이지의 "전지 장착"를 참조하십시오.
팬 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다. 30페이지의 "손목 받침대 분리"를 참조하십시오.
절차 1 시스템 보드에서 팬 케이블을 분리합니다. 2 팬을 시스템 보드에 고정시키는 나사를 제거합니다. 3 팬과 케이블을 들어 올려 컴퓨터 베이스에서 분리합니다.
팬 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 컴퓨터 베이스에 팬을 놓고 팬을 컴퓨터 베이스에 고정하는 나사를 장착합니다. 2 시스템 보드에 팬 케이블을 연결합니다. 후행 조건 1 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오. 4 베이스 덮개를 장착합니다. 21페이지의 "베이스 덮개 장착"를 참조하십시오.
냉각 조립품 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다.
절차 1 방열판에 표시된 번호 순서대로 냉각 조립품을 시스템 보드에 고정시키는 나사를 제거 합니다. 2 냉각 조립품을 들어 올려 시스템 보드에서 분리합니다.
냉각 조립품 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 냉각 조립품 바닥에서 열 그리스를 닦아내고 새 그리스를 다시 바릅니다. 2 냉각 조립품의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 3 방열판에 표시된 번호 순서대로 냉각 조립품을 시스템 보드에 고정하는 나사를 끼웁니다. 후행 조건 1 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다.
하드 드라이브 인터포저 보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다.
절차 1 하드 드라이브 인터포저 보드를 시스템 보드에 고정시키는 나사를 제거합니다. 2 하드 드라이브 인터포저 보드를 시스템 보드에서 분리합니다.
하드 드라이브 인터포저 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 하드 드라이브 인터포저 보드를 시스템 보드에 연결합니다. 2 하드 드라이브 인터포저 보드를 시스템 보드에 고정하는 나사를 장착합니다. 후행 조건 1 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오. 4 베이스 덮개를 장착합니다.
스피커 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다. 30페이지의 "손목 받침대 분리"를 참조하십시오.
절차 1 스피커를 컴퓨터 베이스에 고정하는 나사를 분리합니다. 2 스피커 케이블 배선을 확인하고 배선 가이드에서 케이블을 분리합니다. 3 스피커 케이블과 함께 스피커를 들어 올려 컴퓨터 베이스에서 분리합니다.
스피커 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 컴퓨터 베이스의 맞춤 포스트를 사용하여 스피커를 제자리에 놓습니다. 2 컴퓨터 베이스의 라우팅 가이드를 통해 스피커 케이블을 배선합니다. 3 스피커를 컴퓨터 베이스에 고정하는 나사를 끼웁니다. 후행 조건 1 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오. 4 베이스 덮개를 장착합니다.
디스플레이 조립품 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다.
절차 1 안테나 케이블 배선을 메모하고 배선 가이드에서 케이블을 분리합니다. 2 디스플레이 조립품을 컴퓨터 밑면에 고정하는 나사를 분리합니다. 3 디스플레이 어셈블리를 들어올려 컴퓨터 하단에서 분리합니다.
디스플레이 조립품 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 컴퓨터 베이스에 디스플레이 조립품을 놓고 디스플레이 조립품의 나사 구멍을 컴퓨터 베이스의 나사 구멍과 맞춥니다. 2 컴퓨터 베이스에 디스플레이 조립품을 고정하는 나사를 끼웁니다. 3 컴퓨터 베이스의 배선 가이드를 통해 안테나 케이블을 배선합니다. 후행 조건 1 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 2 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 3 키보드를 장착합니다.
디스플레이 베젤 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다.
절차 1 손가락으로 조심스럽게 디스플레이 베젤의 내부 모서리를 들어 올립니다. 2 디스플레이 베젤을 디스플레이 후면 덮개에서 분리합니다.
디스플레이 베젤 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 디스플레이 베젤을 디스플레이 후면 덮개에 맞추고 조심스럽게 디스플레이 베젤을 제자리에 끼워 넣습니다. 후행 조건 1 디스플레이 조립품을 장착합니다. 59페이지의 "디스플레이 조립품 장착"를 참조하십시오. 2 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 3 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 4 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오. 5 베이스 덮개를 장착합니다.
디스플레이 연결쇠 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 키보드를 분리합니다. 17페이지의 "키보드 분리"를 참조하십시오. 6 손목 받침대를 분리합니다.
절차 1 디스플레이 힌지를 디스플레이 후면 덮개에 고정하는 나사를 제거합니다. 2 디스플레이 패널을 들어올려 디스플레이 후면 덮개에서 분리합니다.
디스플레이 연결쇠 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 디스플레이 힌지의 나사 구멍을 디스플레이 덮개의 나사 구멍에 맞춥니다. 2 디스플레이 힌지를 디스플레이 덮개에 고정하는 나사를 끼웁니다. 후행 조건 1 디스플레이 베젤을 장착합니다. 62페이지의 "디스플레이 베젤 장착"를 참조하십시오. 2 디스플레이 조립품을 장착합니다. 59페이지의 "디스플레이 조립품 장착"를 참조하십시오. 3 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 4 손목 받침대를 장착합니다.
디스플레이 패널 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 메모리 모듈을 분리합니다. 22페이지의 "메모리 모듈 분리"를 참조하십시오. 6 키보드를 분리합니다.
절차 1 디스플레이 후면 덮개에 디스플레이 패널을 고정하는 나사를 제거합니다. 2 디스플레이 패널을 조심스럽게 들어 올려 뒤집습니다.
3 디스플레이 케이블 위에 부착된 테이프를 벗겨냅니다. 4 디스플레이 패널 케이블 커넥터에서 디스플레이 케이블을 분리합니다.
디스플레이 패널 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 디스플레이 케이블을 디스플레이 패널 커넥터에 연결합니다. 2 디스플레이 케이블을 고정하는 테이프를 부착합니다. 3 디스플레이 후면 덮개 위에 조심스럽게 디스플레이 패널을 놓고 디스플레이 패널의 나 사 구멍을 디스플레이 후면 덮개의 나사 구멍에 맞춥니다. 4 디스플레이 패널을 디스플레이 후면 덮개에 고정하는 나사를 끼웁니다. 후행 조건 1 디스플레이 힌지를 장착합니다. 65페이지의 "디스플레이 연결쇠 장착"를 참조하십시오. 2 디스플레이 베젤을 장착합니다.
카메라 모듈 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 메모리 모듈을 분리합니다. 22페이지의 "메모리 모듈 분리"를 참조하십시오. 6 키보드를 분리합니다.
절차 1 카메라 모듈에서 카메라 케이블을 분리합니다. 2 카메라 모듈을 디스플레이 후면 덮개에 고정시키는 나사를 분리합니다. 3 카메라 모듈을 들어 올려 디스플레이 후면 덮개에서 분리합니다.
카메라 모듈 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 디스플레이 후면 덮개의 정렬 포스트를 사용하여 카메라 모듈을 제자리에 끼웁니다. 2 카메라 모듈을 디스플레이 후면 덮개에 고정하는 나사를 장착합니다. 3 카메라 모듈 커넥터에 카메라 케이블을 연결합니다. 후행 조건 1 디스플레이 베젤을 장착합니다. 62페이지의 "디스플레이 베젤 장착"를 참조하십시오. 2 디스플레이 조립품을 장착합니다. 59페이지의 "디스플레이 조립품 장착"를 참조하십시오.
전원 어댑터 포트 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 선행 조건 1 전지를 분리합니다. 12페이지의 "전지 분리"를 참조하십시오. 2 14페이지의 "광학 드라이브 제거"에 설명된 1단계에서 2단계까지의 지침을 따릅니다. 3 24페이지의 "하드 드라이브 제거"에 설명된 1단계에서 3단계까지의 지침을 따릅니다. 4 베이스 덮개를 분리합니다. 20페이지의 "베이스 덮개 분리"를 참조하십시오. 5 메모리 모듈을 분리합니다. 22페이지의 "메모리 모듈 분리"를 참조하십시오. 6 키보드를 분리합니다.
절차 1 전원 어댑터 포트 케이블의 배선 경로를 확인하고 컴퓨터 베이스의 라우팅 가이드에서 전원 어댑터 포트 케이블을 분리합니다. 2 전원 어댑터 포트 및 해당 케이블을 들어 올려 컴퓨터 베이스에서 분리합니다.
전원 어댑터 포트 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 9페 이지의 "시작하기 전에"의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 11페이지 의 "컴퓨터 내부에서 작업한 후"의 지침을 따르십시오. 추가 안전 모범 사례 정보는 Regulatory Compliance(규정 준수) 홈 페이지(dell.com/regulatory_compliance)를 참조 하십시오. 절차 1 전원 어댑터 포트를 제자리로 밀어 넣습니다. 2 전원 어댑터 포트 케이블을 컴퓨터 베이스의 배선 가이드를 통해 배선합니다. 후행 조건 1 디스플레이 조립품을 장착합니다. 59페이지의 "디스플레이 조립품 장착"를 참조하십시오. 2 43페이지의 "시스템 보드 교체"에 설명된 3단계에서 10단계까지의 지침을 따릅니다. 3 손목 받침대를 장착합니다. 33페이지의 "손목 받침대 장착"를 참조하십시오. 4 키보드를 장착합니다. 19페이지의 "키보드 장착"를 참조하십시오.
BIOS 플래싱 사용 가능한 업데이트가 있거나 시스템 보드를 교체할 때, BIOS 플래싱이 필요할 수 있습니 다. BIOS를 플래싱하려면: 1 컴퓨터를 켜십시오. 2 dell.com/support로 이동합니다. 3 Support for Home Users(가정 사용자 지원) 아래 Start Here(여기에서 시작)을 클릭합 니다. 4 컴퓨터의 서비스 태그가 있는 경우, 컴퓨터의 서비스 태그를 입력하고 Submit(제출)를 클릭합니다. 컴퓨터의 서비스 태그가 없는 경우, Detect Service Tag(서비스 태그 검출)를 클릭하면 컴퓨터의 서비스 태그가 자동으로 검출됩니다. 참고: 서비스 태그가 자동으로 검출되지 않으면 제품 카테고리 아래에서 사용 중 인 제품을 선택합니다. 5 Drivers & Downloads(드라이버 및 다운로드) 탭을 클릭합니다. 6 Operating System(운영 체제) 드롭다운에서 컴퓨터에 설치된 운영 체제를 선택합니다. 7 BIOS를 클릭합니다.