Inspiron 5391 Instrukcja serwisowa Model regulacji: P114G Typ regulacji: P114G001 Kwiecień 2021 r. Wer.
Uwagi, przestrogi i ostrzeżenia UWAGA: Napis UWAGA oznacza ważną wiadomość, która pomoże lepiej wykorzystać komputer. OSTRZEŻENIE: Napis PRZESTROGA informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu lub utraty danych, i przedstawia sposoby uniknięcia problemu. PRZESTROGA: Napis OSTRZEŻENIE informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu, obrażeń ciała lub śmierci. © 2019–2021 Dell Inc. lub podmioty zależne. Wszelkie prawa zastrzeżone.
Spis treści Rodzdział 1: Instrukcje dotyczące bezpieczeństwa.............................................................................6 Przed przystąpieniem do serwisowania komputera.......................................................................................................... 6 Przed rozpoczęciem pracy.............................................................................................................................................
Wymontowywanie gniazda zasilacza.......................................................................................................................... 33 Instalowanie gniazda zasilacza.....................................................................................................................................33 Zestaw wyświetlacza..........................................................................................................................................................
Cykl zasilania Wi-Fi.............................................................................................................................................................. 66 Rodzdział 6: Uzyskiwanie pomocy i kontakt z firmą Dell....................................................................
1 Instrukcje dotyczące bezpieczeństwa Aby uchronić komputer przed uszkodzeniem i zapewnić sobie bezpieczeństwo, należy przestrzegać następujących zaleceń dotyczących bezpieczeństwa. O ile nie wskazano inaczej, każda procedura opisana w tym dokumencie zakłada, że użytkownik zapoznał się z informacjami dotyczącymi bezpieczeństwa dostarczonymi z komputerem.
UWAGA: Jeśli używasz innego systemu operacyjnego, wyłącz urządzenie zgodnie z instrukcjami odpowiednimi dla tego systemu. 3. Odłącz komputer i wszystkie urządzenia peryferyjne od gniazdek elektrycznych. 4. Odłącz od komputera wszystkie urządzenia sieciowe i peryferyjne, np. klawiaturę, mysz, monitor itd. 5. Wyjmij z komputera wszystkie karty pamięci i dyski optyczne.
● ● ● ● ● antystatyczną, jeśli trzeba na niej chwilowo kłaść elementy. Fizyczne połączenie opaski na nadgarstek i przewodu wyrównawczego ze skórą użytkownika, matą ESD i urządzeniem jest nazywane połączeniem wyrównawczym. Należy korzystać wyłącznie z zestawu serwisowego zawierającego opaskę na nadgarstek, matę i przewód wyrównawczy. Nie należy używać opaski na nadgarstek bez przewodu. Należy pamiętać, że wewnętrzne przewody opaski na nadgarstek są podatne na uszkodzenia spowodowane normalnym zużyciem.
Po zakończeniu serwisowania komputera Informacje na temat zadania OSTRZEŻENIE: Pozostawienie nieużywanych lub nieprzykręconych śrub wewnątrz komputera może poważnie uszkodzić komputer. Kroki 1. Przykręć wszystkie śruby i sprawdź, czy wewnątrz komputera nie pozostały żadne nieużywane śruby. 2. Podłącz do komputera wszelkie urządzenia zewnętrzne, peryferyjne i kable odłączone przed rozpoczęciem pracy. 3. Zainstaluj karty pamięci, dyski i wszelkie inne elementy wymontowane przed rozpoczęciem pracy. 4.
2 Wymontowywanie i instalowanie komponentów Zalecane narzędzia Procedury przedstawione w tym dokumencie mogą wymagać użycia następujących narzędzi: ● Wkrętak krzyżakowy nr 1 ● Wkrętak z płaskim grotem ● Rysik z tworzywa sztucznego Wykaz śrub UWAGA: Przy wykręcaniu śrub z elementów zalecane jest, aby zanotować typ oraz liczbę śrub, a następnie umieścić je w pudełku na śruby. Umożliwia to przykręcenie właściwych śrub w odpowiedniej liczbie podczas ponownego instalowania elementu.
Tabela 1. Wykaz śrub Element do czego mocowany Typ śruby Ilość Wentylator Płyta główna M2x3 2 Prawy zawias wyświetlacza Płyta główna M2x4 1 Lewy zawias wyświetlacza zestaw pokrywy wyświetlacza i anteny M2,5x3,5 2 Zawiasy M2.5x2.
Kroki 1. Poluzuj trzy śruby mocujące pokrywę dolną. 2. Wykręć cztery śruby (M2x6) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 3. Podważ pokrywę dolną, zaczynając od lewego górnego narożnika zestawu podparcia dłoni i klawiatury. 4. Zdejmij pokrywę dolną z zestawu podparcia dłoni i klawiatury. Instalowanie pokrywy dolnej Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
Kroki 1. Ustaw komputer tak, aby zawiasy były skierowane w Twoją stronę. 2. Umieść pokrywę dolną na zestawie podparcia dłoni i klawiatury, a następnie wciśnij pokrywę dolną na swoje miejsce. 3. Wkręć cztery śruby (M2x6) mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. 4. Dokręć trzy śruby osadzone mocujące pokrywę dolną do zestawu podparcia dłoni i klawiatury. Kolejne kroki 1. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
Kroki 1. Odłącz kabel akumulatora od płyty systemowej. 2. Wykręć cztery śruby (M2x2) mocujące akumulator do zestawu podparcia dłoni i klawiatury. 3. Wykręć śrubę (M1,6x4) mocującą akumulator do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. 4. Wyjmij akumulator z zestawu podparcia dłoni i klawiatury. Instalowanie akumulatora Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
Kroki 1. Podłącz kabel akumulatora do płyty systemowej. 2. Wkręć cztery śruby (M2x2) mocujące akumulator do zestawu podparcia dłoni i klawiatury. 3. Wkręć śrubę (M1,6x4) mocującą akumulator do płyty systemowej oraz zestawu podparcia dłoni i klawiatury. Kolejne kroki 1. Zainstaluj pokrywę dolną. 2. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Bateria pastylkowa Wymontowywanie baterii pastylkowej Wymagania 1.
Kroki 1. Odłącz kabel baterii pastylkowej od płyty systemowej. 2. Wyjmij kabel baterii pastylkowej z prowadnicy. 3. Odłącz baterię pastylkową od zestawu podparcia dłoni i klawiatury. Instalowanie baterii pastylkowej Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji baterii pastylkowej.
Kroki 1. Przymocuj baterię pastylkową do gniazda w zestawie podparcia dłoni i klawiatury. 2. Umieść kabel baterii pastylkowej w prowadnicy. 3. Podłącz kabel baterii pastylkowej do płyty systemowej. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Dysk SSD Wymontowywanie dysku SSD M.2 2280 Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2.
Instalowanie dysku SSD M.2 2280 Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji dysku SSD. Kroki 1. Dopasuj wycięcie na dysku SSD do zaczepu w gnieździe dysku SSD, a następnie wsuń dysk SSD do gniazda dysku SSD. 2. Wkręć śrubę (M2x2,5) mocującą dysk SSD do płyty systemowej. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3.
Kroki 1. Wykręć śrubę (M2x2,5) mocującą wspornik dysku SSD do płyty systemowej. 2. Przesuń i wyjmij wspornik dysku SSD z gniazda na płycie systemowej. 3. Przesuń i wyjmij moduł dysku SSD z gniazda na płycie systemowej. Instalowanie dysku SSD M.2 2230 Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji dysku SSD.
Kroki 1. Dopasuj wycięcie na dysku SSD do zaczepu w gnieździe dysku SSD, a następnie wsuń dysk SSD do gniazda dysku SSD. 2. Wsuń wspornik dysku SSD na kartę SSD na płycie systemowej. 3. Wkręć śrubę (M2x2,5) mocującą dysk SSD do płyty systemowej. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Radiator Wymontowywanie radiatora Wymagania 1.
Kroki 1. Odklej taśmę mocującą radiator do płyty systemowej. 2. W kolejności odwrotnej do wskazanej na radiatorze (7>6>5>4>3>2>1) poluzuj siedem śrub mocujących radiator do płyty systemowej. 3. Zdejmij radiator z płyty systemowej. Instalowanie radiatora Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji pokrywy dolnej.
Kroki 1. Dopasuj otwory na śruby w radiatorze do otworów w płycie systemowej. 2. W kolejności wskazanej na radiatorze dokręć siedem śrub osadzonych mocujących radiator do płyty systemowej. 3. Przyklej taśmę z tworzywa sztucznego mocującą radiator do płyty systemowej. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Wentylator Wymontowywanie wentylatora Wymagania 1.
Kroki 1. Odłącz kabel płyty I/O od płyty systemowej i płyty I/O. UWAGA: Ten krok ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN. 2. Wkręć dwie śruby (M2x3) mocujące wentylator do płyty systemowej. 3. Lekko unieś wentylator z zestawu podparcia dłoni i klawiatury. 4. Odłącz kabel wentylatora od płyty systemowej i całkowicie zdejmij wentylator z zestawu podparcia dłoni i klawiatury.
Kroki 1. Podłącz kabel wentylatora do złącza na płycie systemowej. 2. Dopasuj otwory na śruby wentylatora do otworów w zestawie podparcia dłoni i klawiatury. 3. Wkręć dwie śruby (M2x3) mocujące wentylator do zestawu podparcia dłoni i klawiatury. 4. Podłącz kabel płyty I/O do płyty systemowej i płyty I/O. UWAGA: Ten krok ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3.
Głośniki Wymontowywanie głośników Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wymontuj pokrywę dolną. 3. Wymontuj akumulator. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania głośników. Kroki 1. Otwórz zatrzask i odłącz kabel tabliczki dotykowej od płyty systemowej. 2. Odłącz kabel głośnika od płyty systemowej. 3. Odlep taśmy mocujące kabel głośników do zestawu podparcia dłoni i klawiatury. 4.
UWAGA: Przed wyjęciem głośników należy zwrócić uwagę na położenie gumowych pierścieni. 5. Wyjmij głośniki razem z kablem z zestawu podparcia dłoni i klawiatury. Instalowanie głośników Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji głośników. Kroki 1.
Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Karta sieci WLAN Wymontowywanie karty sieci WLAN Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wymontuj pokrywę dolną. 3. Wymontuj akumulator. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania karty sieci WLAN. Kroki 1.
Kroki 1. Podłącz kable antenowe do karty sieci WLAN. 2. Dopasuj wycięcie na karcie sieci WLAN do wypustki w gnieździe karty sieci WLAN i wsuń kartę do gniazda pod kątem. 3. Wyrównaj wspornik karty sieci WLAN i załóż go na kartę. 4. Wkręć śrubę (M2x2,5) mocującą wspornik karty sieci WLAN do karty sieci WLAN. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
Kroki 1. Wykręć śrubę (M2x2,5) mocującą wspornik karty sieci WWAN do karty. 2. Przed zdjęciem wspornika karty sieci WWAN z karty zwróć uwagę na jego wyrównanie. 3. Odłącz kable antenowe od karty sieci WWAN. 4. Przesuń i wyjmij kartę sieci WWAN z gniazda. Instalowanie karty sieci WWAN Wymagania UWAGA: Ta procedura ma zastosowanie tylko w przypadku komputerów wyposażonych w kartę sieci WWAN. W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
Kroki 1. Dopasuj wycięcie na karcie sieci WWAN do wypustki w gnieździe karty sieci WWAN i wsuń kartę do gniazda pod kątem. 2. Podłącz kable antenowe do karty sieci WWAN i umieść wspornik karty sieci WWAN na samej karcie. 3. Wkręć jedną śrubę (M2x2,5) mocującą wspornik karty WWAN do samej karty. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną. 3. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
Kroki 1. Odklej taśmy mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 2. Otwórz zatrzask i odłącz kabel tabliczki dotykowej od płyty systemowej. 3. Wykręć trzy śruby (M1,6x2) mocujące wspornik tabliczki dotykowej do zestawu podparcia dłoni i klawiatury. 4. Zdejmij wspornik tabliczki dotykowej z zestawu podparcia dłoni i klawiatury. 5. Wykręć dwie śruby (M1,6x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 6.
Kroki 1. Umieść tabliczkę dotykową we wnęce w zestawie podparcia dłoni i klawiatury. 2. Wkręć dwie śruby (M1,6x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury. 3. Umieść wspornik tabliczki dotykowej w gnieździe w zestawie podparcia dłoni i klawiatury. 4. Wkręć trzy śruby (M1,6x2) mocujące wspornik tabliczki dotykowej do zestawu podparcia dłoni i klawiatury. 5. Podłącz kabel tabliczki dotykowej do złącza na płycie systemowej i zamknij zatrzask, aby zamocować kabel. 6.
Złącze zasilacza Wymontowywanie gniazda zasilacza Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wymontuj pokrywę dolną. 3. Wymontuj akumulator. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania gniazda zasilacza. Kroki 1. Wykręć śrubę (M2,5x3,5) mocującą wspornik kabla wyświetlacza do płyty systemowej. 2. Wykręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 3.
Kroki 1. Podłącz kabel gniazda zasilacza do płyty systemowej. 2. Wkręć śrubę (M2x3) mocującą gniazdo zasilacza do zestawu podparcia dłoni i klawiatury. 3. Wyrównaj i umieść wspornik kabla wyświetlacza na płycie systemowej. 4. Wkręć śrubę (M2,5x3,5) mocującą wspornik kabla wyświetlacza do płyty systemowej. 5. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 6. Wkręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. Kolejne kroki 1. Zainstaluj akumulator. 2. Zainstaluj pokrywę dolną.
Wymontowywanie i instalowanie komponentów 35
Kroki 1. Wykręć śrubę (M2,5x3,5) mocującą wspornik kabla wyświetlacza do płyty systemowej. 2. Zdejmij wspornik kabla wyświetlacza z płyty systemowej. 3. Pociągając za uchwyt, odłącz kabel wyświetlacza od płyty systemowej. 4. Wykręć dwie śruby (M2,5x3,5) mocujące lewy zawias wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. 5. Wykręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 6. Odchyl zawiasy wyświetlacza o 90 stopni. 7.
Instalowanie zestawu wyświetlacza Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji zestawu wyświetlacza.
Kroki 1. Wyrównaj i umieść zestaw podparcia dłoni i klawiatury w zestawie wyświetlacza. 2. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 3. Wkręć dwie śruby (M2,5x3,5) mocujące lewy i prawy zawias wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. 4. Wkręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 5. Podłącz kabel wyświetlacza do złącza na płycie systemowej. 6. Dopasuj i załóż wspornik kabla wyświetlacza na kabel wyświetlacza. 7.
Karta we/wy Wymontowywanie płyty we/wy Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj wentylator. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania karty I/O. Kroki 1. Wykręć dwie śruby (M2,5x3,5) mocujące lewy zawias wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. 2. Odchyl zawiasy wyświetlacza o 90 stopni. 3.
4. Otwórz zatrzask i odłącz kabel płyty we/wy od płyty we/wy. 5. Wykręć śrubę (M2,5x2,5) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 6. Wykręć śrubę (M2x3) mocującą kartę I/O do zestawu podparcia dłoni i klawiatury. 7. Wyjmij płytę I/O z zestawu podparcia dłoni i klawiatury. Instalowanie karty wejścia/wyjścia Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
5. Przyklej taśmę mocującą do karty I/O. 6. Zamknij zawiasy wyświetlacza, korzystając z wypustek. 7. Wkręć dwie śruby (M2,5x3,5) mocujące lewy zawias wyświetlacza do karty I/O oraz zestawu podparcia dłoni i klawiatury. Kolejne kroki 1. 2. 3. 4. Zainstaluj wentylator. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. płyta przycisku zasilania Wymontowywanie płyty przycisku zasilania Wymagania 1. 2. 3. 4. 5. 6.
Instalowanie płyty przycisku zasilania Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji płyty przycisku zasilania. Kroki 1. Dopasuj otwór w płycie przycisku zasilania do otworu w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M1,6x2) mocującą płytę przycisku zasilania do zestawu podparcia dłoni i klawiatury. 3.
1. 2. 3. 4. 5. 6. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj kartę sieci WLAN. Wymontuj wentylator. Wymontuj płytę we/wy. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania przycisku zasilania z czytnikiem linii papilarnych. Kroki 1. Wykręć śrubę (M1,6x2) mocującą wspornik przycisku zasilania do zestawu podparcia dłoni i klawiatury. 2.
Kroki 1. Umieść przycisk zasilania z czytnikiem linii papilarnych w zestawie podparcia dłoni i klawiatury. 2. Wkręć śrubę (M1,6x2) mocującą przycisk zasilania z czytnikiem linii papilarnych do zestawu podparcia dłoni i klawiatury. 3. Podłącz kabel czytnika linii papilarnych do płyty czytnika linii papilarnych i zamknij zatrzask, aby zamocować kabel. 4. Dopasuj wspornik przycisku zasilania i umieść go na zestawie podparcia dłoni i klawiatury. 5.
Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę wymontowywania płyty systemowej. Kroki 1. Wykręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 2. Wykręć śrubę (M2x4) mocującą wspornik kabla wyświetlacza do płyty systemowej. 3. Wykręć śrubę (M2,5x3,5) mocującą wspornik portu USB Type-C do płyty systemowej. 4. Odklej taśmę mocującą kabel płyty we/wy do płyty systemowej. 5. Otwórz zatrzask złącza i odłącz kabel płyty we/wy od płyty systemowej. 6.
Instalowanie płyty systemowej Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element. Informacje na temat zadania Na ilustracji przedstawiono umiejscowienie i procedurę instalacji płyty systemowej. Kroki 1. Włóż złącza płyty systemowej do otworów w zestawie podparcia dłoni i klawiatury, a następnie dopasuj otwory na śruby w płycie systemowej do otworów w zestawie podparcia dłoni i klawiatury. 2.
9. Podłącz kabel czytnika linii papilarnych do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 10. Podłącz kabel głośników do płyty systemowej. 11. Podłącz kabel karty I/O do płyty systemowej i zamknij zatrzask, aby zamocować kabel. 12. Przyklej taśmę mocującą kabel płyty we/wy do płyty systemowej. 13. Wkręć śrubę (M2x4) mocującą prawy zawias wyświetlacza do płyty systemowej. 14. Wkręć śrubę (M2x4) mocującą wspornik kabla wyświetlacza do płyty systemowej. 15.
Kroki Po wykonaniu czynności wstępnych pozostanie zestaw podparcia dłoni i klawiatury. UWAGA: W przypadku komputerów wyposażonych w kartę sieci WWAN kable antenowe są częścią tylnej pokrywy wyświetlacza. UWAGA: Płytę systemową można wyjąć bez demontowania radiatora. Instalowanie zestawu podparcia dłoni i klawiatury Wymagania W przypadku wymiany elementu przed wykonaniem procedury instalacji wymontuj wcześniej zainstalowany element.
Kroki Połóż zestaw podparcia dłoni i klawiatury na płaskiej powierzchni. UWAGA: W przypadku komputerów wyposażonych w kartę sieci WWAN kable antenowe są częścią tylnej pokrywy wyświetlacza. Kolejne kroki 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Zainstaluj tabliczkę dotykową. Zainstaluj gniazdo zasilacza. Zainstaluj przycisk zasilania z czytnikiem linii papilarnych lub przycisk zasilania, zależnie od konfiguracji komputera. Zainstaluj zestaw wyświetlacza. Zainstaluj płytę systemową. Zainstaluj głośniki.
3 Sterowniki urządzeń Narzędzie instalacji programu Intel Chipset Software W Menedżerze urządzeń (Device Manager), sprawdź, czy jest zainstalowany sterownik chipsetu. Zainstaluj aktualizacje sterowników chipsetów Intel z witryny www.dell.com/support. Sterowniki grafiki wideo W Menedżerze urządzeń (Device Manager), sprawdź, czy jest zainstalowany sterownik wideo. Zainstaluj aktualizację sterownika wideo z witryny www.dell.com/support.
4 Program konfiguracji systemu UWAGA: Zależnie od komputera oraz zainstalowanych w nim urządzeń wymienione w tej sekcji pozycje mogą, ale nie muszą, pojawiać się na ekranie. Program konfiguracji systemu OSTRZEŻENIE: Ustawienia konfiguracji systemu BIOS powinni zmieniać tylko doświadczeni użytkownicy. Niektóre zmiany mogą spowodować nieprawidłową pracę komputera.
Klawisze Nawigacja Esc Powrót do poprzedniej strony do momentu wyświetlenia ekranu głównego. Naciśnięcie klawisza Esc na ekranie głównym powoduje wyświetlenie komunikatu z monitem o zapisanie zmian i ponowne uruchomienie systemu. Boot Sequence Opcja Boot Sequence umożliwia pominięcie kolejności urządzeń startowych zdefiniowanej w programie konfiguracji systemu i uruchomienie komputera z określonego urządzenia (na przykład z napędu dysków optycznych lub z dysku twardego).
Tabela 2. Opcje konfiguracji systemu — menu System information (Informacje o systemie) Informacje ogólne Processor Information (Informacje o procesorze) Processor Type (Typ procesora) Wyświetla typ procesora. Maximum Clock Speed (Maksymalna szybkość zegara) Wyświetla maksymalną szybkość zegara procesora. Core Count (Liczba rdzeni) Wyświetla liczbę rdzeni procesora. Processor L2 Cache (Pamięć podręczna L2 procesora) Wyświetla ilość pamięci podręcznej procesora poziomu L2.
Tabela 3. Opcje konfiguracji systemu — menu Boot Options (Opcje uruchamiania) Opcje uruchamiania Boot Mode Boot Mode: UEFI only (Tryb uruchamiania: tylko UEFI) Wyświetla tryb uruchamiania tego komputera. Enable Boot Device (Włącz urządzenia rozruchowe) Umożliwia włączanie lub wyłączanie urządzeń rozruchowych dla tego komputera. Boot Sequence Wyświetla sekwencję rozruchu. BIOS Setup Advanced Mode (tryb zaawansowany konfiguracji BIOS) Włącza lub wyłącza zaawansowane ustawienia systemu BIOS.
Tabela 4. Opcje konfiguracji systemu — menu System Configuration (Konfiguracja systemu) Konfiguracja systemu Drive Information (Informacje o dysku) Wyświetla informacje o różnych wbudowanych dyskach. Miscellaneous Devices Umożliwia włączanie i wyłączanie różnych zintegrowanych urządzeń. Enable Camera (Włącz kamerę) Umożliwia włączanie i wyłączanie kamery. Ustawienie domyślne: ON (włączony). Keyboard Illumination Umożliwia skonfigurowanie trybu działania funkcji podświetlenia klawiatury.
Tabela 6. Opcje konfiguracji systemu — Security menu (Menu Zabezpieczenia) Security (Zabezpieczenia) Allows Wireless Switch Changes (Zezwól na włączanie/wyłączanie urządzeń bezprzewodowych) Umożliwia włączanie i wyłączanie wprowadzania zmian konfiguracji, gdy jest ustawione hasło administratora.
Tabela 7. Opcje konfiguracji systemu — menu Secure Boot (Bezpieczne uruchamianie) Secure Boot (Bezpieczny rozruch) Secure Boot Mode Wybiera tryb działania funkcji Secure Boot. Ustawienie domyślne: Deployed Mode (Tryb wdrożony). UWAGA: W celu normalnego działania funkcji Secure Boot należy wybrać tryb Deployed Mode. Tabela 8.
Tabela 10. Opcje konfiguracji systemu — menu Power Management (Zarządzanie energią) Zarządzanie energią Battery Charge Configuration Umożliwia zasilanie komputera z akumulatora w określonych godzinach, nawet jeśli podłączone jest zasilanie sieciowe. Poniższe opcje pozwalają wyłączyć korzystanie z zasilacza w określonych porach dnia. Wartość domyślna: Adaptive (Adaptacyjne). Ustawienia akumulatora są automatycznie optymalizowane odpowiednio do typowego sposobu jego wykorzystywania.
Tabela 12. Opcje konfiguracji systemu — menu POST Behavior (Zachowanie podczas testu POST) Zachowanie podczas testu POST Enable Adapter Warnings (Włącz ostrzeżenia Umożliwia wyświetlanie podczas uruchamiania komputera komunikatów zasilacza) ostrzegawczych dotyczących zasilacza. Ustawienie domyślne: ON (włączony). Extend BIOS POST Time (Dodatkowe opóźnienie przed rozruchem) Umożliwia skonfigurowanie czasu ładowania testu POST systemu BIOS. Fastboot Konfiguruje szybkość procesu rozruchu UEFI.
Tabela 14. Opcje konfiguracji systemu — Maintenance (Konserwacja) Maintenance (Konserwacja) ME) lub usterki sprzętowej. Obraz odzyskiwania musi istnieć na niezaszyfrowanej partycji na dysku. BIOS Auto-Recovery (Automatyczne odzyskiwanie systemu BIOS) Umożliwia komputerowi automatyczne odzyskiwanie systemu BIOS bez działań użytkownika. Ta funkcja wymaga, aby opcja BIOS Recovery from Hard Drive była włączona. Ustawienie domyślne: OFF (wyłączony).
4. Odczekaj minutę. 5. Zainstaluj baterię pastylkową. 6. Podłącz kabel akumulatora do płyty systemowej. 7. Zainstaluj pokrywę dolną. Czyszczenie hasła systemowego i hasła systemu BIOS (konfiguracji systemu) Informacje na temat zadania W celu wyczyszczenia hasła komputera lub systemu BIOS skontaktuj się z działem pomocy technicznej Dell: www.dell.com/contactdell.
5 Rozwiązywanie problemów Program diagnostyczny ePSA (Enhanced Pre-Boot System Assessment) Informacje na temat zadania Test diagnostyczny ePSA obejmuje pełną kontrolę elementów sprzętowych. Test ePSA jest wbudowany w systemie BIOS i uruchamiany wewnętrznie przez system BIOS.
● Komputer jest w stanie uśpienia, hibernacji lub jest wyłączony. Kontrolka stanu zasilania i stanu akumulatora miga światłem bursztynowym wraz z uruchomionymi kodami dźwiękowymi, wskazując błędy. Na przykład kontrolka stanu zasilania i stanu akumulatora miga dwa razy światłem bursztynowym, a potem następuje pauza, a następnie światłem białym trzy razy, a potem następuje pauza. Sekwencja 2,3 jest wykonywana do chwili wyłączenia komputera. Oznacza ona brak pamięci lub pamięci RAM.
Tabela 18. Diagnostyka Wbudowany autotest M-BIST Wbudowany autotest wyświetlacza LCD (L-BIST) Wskaźnik usterki Żółte światło wskaźnika LED baterii Kod błędu wskazywany przez miganie wskaźnika LED baterii [żółty, biały] = [2, 8] Instrukcja naprawy Wykryto problem z płytą systemową. Wykryto problem z płytą systemową. M-BIST Informacje na temat zadania Narzędzie diagnostyczne M-BIST (wbudowany autotest) umożliwia diagnozowanie awarii płyty systemowej.
Przywracanie systemu operacyjnego Jeśli komputer nie jest w stanie uruchomić systemu operacyjnego nawet po kilku próbach, automatycznie uruchamia się narzędzie Dell SupportAssist OS Recovery. Dell SupportAssist OS Recovery to samodzielne narzędzie instalowane fabrycznie na wszystkich komputerach firmy Dell z systemem operacyjnym Windows 10. Składa się ono z narzędzi ułatwiających diagnozowanie i rozwiązywanie problemów, które mogą wystąpić przed uruchomieniem systemu operacyjnego komputera.
Uwalnianie ładunków elektrycznych Informacje na temat zadania Ładunki elektryczne pozostają w komputerze nawet po jego wyłączeniu i wyjęciu akumulatora. W tej procedurze opisano sposób rozładowywania tych ładunków: Kroki 1. Wyłącz komputer. 2. Wymontuj pokrywę dolną. 3. Wymontuj akumulator. 4. Naciśnij przycisk zasilania i przytrzymaj go przez 15 sekund, aby usunąć pozostałe ładunki elektryczne. 5. Zainstaluj akumulator. 6. Zainstaluj pokrywę dolną. 7. Włącz komputer.
6 Uzyskiwanie pomocy i kontakt z firmą Dell Narzędzia pomocy technicznej do samodzielnego wykorzystania Aby uzyskać informacje i pomoc dotyczącą korzystania z produktów i usług firmy Dell, można skorzystać z następujących zasobów internetowych: Tabela 19. Narzędzia pomocy technicznej do samodzielnego wykorzystania Narzędzia pomocy technicznej do samodzielnego wykorzystania Lokalizacja zasobów Informacje o produktach i usługach firmy Dell www.dell.