Inspiron 5400 2n1 Servicemanual Forordningsmodel: P126G Forordningstype: P126G002 June 2020 rev.
Bemærk, forsigtig og advarsel BEMÆRK: En NOTE angiver vigtige oplysninger, som hjælper dig med at bruge computeren bedre. FORSIGTIG: FORSIGTIG angiver enten en mulig beskadigelse af hardware eller tab af data, og oplyser dig om, hvordan du kan undgå dette problem. ADVARSEL: ADVARSEL angiver risiko for tingskade, legemsbeskadigelse eller død. © 2020 Dell Inc. eller dets associerede selskaber. Alle rettigheder forbeholdes. Dell, EMC, og andre varemærker er varemærker tilhørende Dell Inc.
Indholdsfortegnelse Kapitel 1: Arbejde med indersiden af din computer............................................................................. 5 Før du udfører arbejde på computerens indvendige dele.................................................................................................5 Sikkerhedsinstruktioner.........................................................................................................................................................
Sådan monteres blæseren............................................................................................................................................ 37 I/O-kort.................................................................................................................................................................................37 Sådan fjernes I/O-kortet.....................................................................................................................................
1 Arbejde med indersiden af din computer Før du udfører arbejde på computerens indvendige dele Om denne opgave BEMÆRK: Billederne i dette dokument kan afvige fra din computer afhængigt af den bestilte konfiguration. Trin 1. Gem og luk alle åbne filer, og luk alle åbne programmer. 2. Sluk computeren. Klik på Start > Tænd/sluk > Luk computeren. BEMÆRK: Hvis du bruger et andet operativsystem, se i dokumentationen for dit operativsystem for vejledning ved nedlukning. 3.
FORSIGTIG: Når du fjerner et kabel, skal du trække i stikket eller tappen, ikke i selve kablet. Nogle kabler har stik med låsetappe eller tommelskruer, som du skal frigøre, før du tager kablet ud. Når kabler frakobles skal du sikre dig, at de flugter, så benene på stikkene ikke bøjes. Når kabler tilsluttes skal du sikre dig, at portene og stikkene flugter og sidder rigtigt i forhold til hinanden. FORSIGTIG: Tryk for at skubbe eventuelle installerede kort ud af mediekortlæseren.
• • • • • Tester til ESD-håndledsrem – Ledningerne inde i en ESD-rem er tilbøjelige til at blive beskadiget over tid. Når et uovervåget sæt benyttes, er det bedste praksis regelmæssigt at teste remmen før brug og som minimum teste en gang om ugen. En håndledsremtester er den bedste metode til at udføre denne test. Hvis du ikke har din egen håndledsremtester, skal du kontakte regionskontoret for at høre, om de har en.
Trin 1. 2. 3. 4. 5. 8 Genmonter alle skruer, og sørg for, at der ikke er løse skruer inde i din computer. Tilslut alle eksterne enheder, alt tilbehør eller alle kabler, som du fjernede, før du begyndte at udføre arbejde på computeren. Udskift alle mediekort, harddiske eller andre dele, som du fjernede, før du begyndte at udføre arbejde på computeren. Tilslut computeren og alle tilsluttede enheder til deres stikkontakter.
2 Sådan fjernes og installeres komponenter Anbefalet værktøj Procedurerne i dette dokument kræver eventuelt følgende værktøj: • • Stjerneskruetrækker nr. 0 og nr. 1 Plastikpen Liste over skruer BEMÆRK: Når skruer fjernes fra en komponent, anbefales det at bemærke skruetypen, antallet af skruer, og dernæst igen placere dem i en skrueopbevaringsboks. Dette er for at sikre, at det korrekte antal skruer og den korrekte skruetype gendannes, når komponenten er udskiftet..
Tabel 1.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
Bunddæksel Sådan fjernes bunddækslet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Om denne opgave De følgende billeder angiver placeringen af bunddækslet og giver en visuel fremstilling af fjernelsesproceduren.
Sådan fjernes og installeres komponenter 13
Trin 1. Fjern de seks skruer (M2x4), der fastgør bunddækslet til håndledsstøtte- og tastaturmodulet. 2. Løsn de tre skruer, der fastgør bunddækslet til håndledsstøtte- og tastaturmodulet. BEMÆRK: Når de tre fastmonterede skruer er løsnet, hopper bunddækslet op, og der dukker et hul op mellem bunddækslet og håndledsstøttemodulet. 3. Start fra det øverste højre hjørne, og lirk bunddækslet op med en plastikpen for at frigøre bunddækslet fra håndledsstøtte- og tastaturmodulet.
Sådan fjernes og installeres komponenter 15
Trin 1. Slut batterikablet til systemkortet. 2. Påsæt tapen, der fastgør batterikablet til systemkortet. 3. Sørg for, at skruehullerne på bunddækslet flugter med skruehullerne i håndledsstøtte- og tastaturmodulet, og klik bunddækslet på plads. 4. Genmonter de seks skruer (M2x4), der fastgør bunddækslet til håndledsstøtte- og tastaturmodulet. 5. Stram de tre skruer, der fastgør bunddækslet til håndledsstøtte- og tastaturmodulet. Næste trin 1.
Trin 1. 2. 3. 4. Pil tapen, der fastgør batterikablet til systemkortet, af (hvis det ikke allerede er gjort). Kobl batterikablet fra systemkortet (hvis det ikke allerede er gjort). Fjern de fem skruer (M2x3), der fastgør batteriet til håndledsstøtte- og tastaturmodulet. Løft batteriet af håndledsstøtte- og tastaturmodulet. Sådan monteres batteriet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Trin 1. 2. 3. 4. Placer vha. styremærkerne batterier på håndledsstøtte- og tastaturmodulet. Genmonter de fem skruer (M2x3), der fastgør batteriet til håndledsstøtte- og tastaturmodulet. Slut batterikablet til systemkortet. Påsæt tapen, der fastgør batterikablet til systemkortet. Næste trin 1. Monter bunddækslet. 2. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Møntcellebatteri Sådan fjernes møntcellebatteriet Forudsætninger 1.
Trin 1. Kobl møntcellebatteriet fra I/O-kortet. 2. Fjern møntcellebatteriets kabel fra kabelkanalen på blæseren. 3. Brug en plastikpen til at lirke møntcellebatteriet ud af slotten på håndledsstøtte- og tastaturmodulet. Sådan monteres møntcellebatteriet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Trin 1. Før møntcellebatteriet ind i slotten på håndledsstøtte- og tastaturmodulet. 2. Løft højtalerkablet, og før møntcellebatteriets kabel gennem kabelkanalen på blæseren. 3. Slut møntcellebatteriets kabel til I/O-kortet. Næste trin 1. Monter bunddækslet. 2. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Hukommelsesmoduler Sådan fjernes hukommelsesmodulerne Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern bunddækslet.
Trin 1. Løft flappen for at få adgang til hukommelsesmodulet. 2. Brug fingerspidserne til forsigtigt at adskille fastgørelsesklemmerne på hver side af hukommelsesmodulslotten, indtil modulet springer op. 3. Træk og fjern hukommelsesmodulet fra dets slot. BEMÆRK: Gentag trin 2 til trin 3 for at fjerne andre hukommelsesmoduler, der er monteret i din computer.
Trin 1. 2. 3. 4. Løft flappen for at få adgang til hukommelsesmodulets slot. Juster hukommelsesmodulets indhak med tappen på hukommelsesmodulslotten. Skub hukommelsesmodulet ind i hukommelsesslotten i en lige vinkel. Tryk hukommelsesmodulet ned, indtil det klikker på plads. BEMÆRK: Hvis du ikke hører et klik, skal du fjerne hukommelsesmodulet og sætte det i igen. BEMÆRK: Gentag trin 2 til trin 4 for at montere hukommelsesmodulerne i din computer. Næste trin 1. Monter bunddækslet. 2.
Højttalere Sådan fjernes højtalerne Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern bunddækslet. Om denne opgave Følgende billede angiver placeringen af højtalerne og giver en visuel fremstilling af fjernelsesproceduren. Trin 1. Kobl højtalerkablet fra systemkortet. 2. Bemærk kabelføringen for højtalerne, og fjern højtalerkablet fra kabelkanalen på håndledsstøtte- og tastaturmodulet. 3.
Trin 1. Anbring vha. styremærkerne og gummidutterne højttalerne i deres slots på håndledsstøtte- og tastaturmodulet. 2. Før højtalerkablet gennem kabelkanalerne på håndledsstøtte- og tastaturmodulet. 3. Slut højtalerkablet til systemkortet. Næste trin 1. Monter bunddækslet. 2. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Varme-sink Sådan fjernes varmelegemet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
Trin 1. Løsn de syv fastmonterede skruer, der fastgør varmelegemet til systemkortet i omvendt rækkefølge (som den er angivet på varmelegemet). 2. Løft varmelegemet af systemkortet. Sådan monteres varmelegemet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. FORSIGTIG: Forkert placering af varmelegemet kan beskadige systemkortet og processoren.
Trin 1. Få skruehullerne i varmelegemet til at flugte med skruehullerne i systemkortet. 2. Spænd de syv fastmonterede skruer, der fastgør varmelegemet til systemkortet i rækkefølge (som angivet på varmelegemet). Næste trin 1. Monter bunddækslet. 2. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Strømadapterport Sådan fjernes strømadapterporten Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern bunddækslet.
Trin 1. 2. 3. 4. 5. 6. Fjern de tre skruer (M2,5x5), der fastgør det højre skærmhængsel til håndledsstøtte- og tastaturmodulet. Åbn det højre skærmhængsel i en vinkel på 90 grader. Pil tapen, der fastgør strømadapterportens kabel til systemkortet, af. Kobl strømadapterportens kabel fra systemkortet. Fjern skruen (M2x3), der fastgør strømadapterporten til håndledsstøtte- og tastaturmodulet. Løft strømadapterporten og dens kabel op fra håndledsstøtte- og tastaturmodulet.
Trin 1. 2. 3. 4. 5. 6. 7. Placer strømadapterporten i slotten på håndledsstøtte- og tastaturmodulet. Genmonter skruen (M2x3), der fastgør strømadapterporten til håndledsstøtte- og tastaturmodulet. Før strømadapterportens kabel gennem kabelkanalerne på håndledsstøtte- og tastaturmodulet. Slut strømadapterportens kabel til systemkortet. Påsæt tapen, der fastgør strømadapterporten til systemkortet. Luk det højre skærmhængsel.
Trin 1. 2. 3. 4. 5. Fjern de tre skruer (M2x2), der fastgør pegefeltets bøjle til håndledsstøtte- og tastaturmodulet. Åbn låsen, og kobl pegefeltkablet fra pegefeltet. Pil tapen, der fastgør pegefeltet til håndledsstøtte- og tastaturmodulet, af. Fjern de to skruer (M2x2), der fastgør pegefeltet til håndledsstøtte- og tastaturmodulet. Skub og løft pegefeltet væk fra håndledsstøtte- og tastaturmodulet.
Trin 1. 2. 3. 4. 5. 6. Skub pegefeltet ind i slotten på håndledsstøtte- og tastaturmodulet. Genmonter de to skruer (M2x2), der fastgør pegefeltet på håndledsstøtte- og tastaturmodulet. Påsæt tapen, der fastgør pegefeltet til håndledsstøtte- og tastaturmodulet. Skub pegefeltets kabel ind i stikket på pegefeltet, og luk låsen for at fastgøre kablet. Placer pegefeltets bøjle i slotten på håndledsstøtte- og tastaturmodulet.
Trin 1. 2. 3. 4. Fjern skruen (M2x3), der fastgør solid state-drevets termiske bøjle til håndledsstøtte- og tastaturmodulet. Løft solid state-drevets termiske bøjle af håndledsstøtte- og tastaturmodulet. Fjern skruen (M2x3), som fastgør solid state-drevet til solid state-drevets bøjle. Træk og fjern solid state-drevet fra dets slot. Sådan monteres M.2 2230-solid state-drevet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Følgende billede angiver placeringen af M.2 2230-solid state-drevet og giver en visuel fremstilling af installationsproceduren. Trin 1. Fjern skruen (M1,6x2,5), der fastgør solid state-drevets bøjle til håndledsstøtte- og tastaturmodulet.
2. 3. 4. 5. 6. 7. 8. 9. Drej solid state-drevets bøjle 180 grader. Før solid state-drevets bøjle ind i den anden slot til solid state-drevets bøjle på håndledsstøtte- og tastaturmodulet. Genmonter skruen (M1,6x2,5), der fastgør solid state-drevets bøjle til håndledsstøtte- og tastaturmodulet. Ret indhakket på solid state-drevet ind efter tappen på dets slot. Skub solid state-drevets modul skråt ind i slotten til solid state-drevet. Genmonter skruen (M2x3), som fastgør solid state-drevet til dets bøjle.
Trin 1. 2. 3. 4. Fjern skruen (M2x3), der fastgør solid state-drevets termiske bøjle til håndledsstøtte- og tastaturmodulet. Løft solid state-drevets termiske bøjle af håndledsstøtte- og tastaturmodulet. Fjern skruen (M2x3), som fastgør solid state-drevet til solid state-drevets bøjle. Træk og fjern solid state-drevet fra dets slot. Sådan monteres M.2 2280-solid state-drevet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages.
Følgende billede angiver placeringen af M.2 2280-solid state-drevet og giver en visuel fremstilling af installationsproceduren. BEMÆRK: Udfør trin 1-3, hvis du udskifter M.2 2230-solid state-drevet med et M.2 2280-solid state-drev.
Trin 1. 2. 3. 4. 5. 6. 7. 8. 9. Fjern skruen (M1,6x2,5), der fastgør solid state-drevets bøjle til håndledsstøtte- og tastaturmodulet. Drej solid state-drevets bøjle 180 grader. Før solid state-drevets bøjle ind i den anden slot til solid state-drevets bøjle på håndledsstøtte- og tastaturmodulet. Genmonter skruen (M1,6x2,5), der fastgør solid state-drevets bøjle til håndledsstøtte- og tastaturmodulet. Ret indhakket på solid state-drevet ind efter tappen på dets slot.
Sådan monteres blæseren Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Følgende billede angiver placeringen af blæseren og giver en visuel fremstilling af monteringsproceduren. Trin 1. Anbring vha. styremærkerne blæseren på håndledsstøtte- og tastaturmodulet. 2. Genmonter de to skruer (M2x2), der fastgør systemblæseren til håndledsstøtte- og tastaturmodulet. 3. Slut blæserkablet til systemkortet.
Trin 1. 2. 3. 4. 5. 6. 7. 8. Fjern de to skruer (M2,5x5), der fastgør det venstre skærmhængsel til håndledsstøtte- og tastaturmodulet. Åbn det venstre skærmhængsel i en vinkel på 90 grader. Pil tapen, der fastgør I/O-kortets kabel til I/O-kortet, af. Åbn låsen, og kobl I/O-kortets kabel fra I/O-kortet. Åbn låsen, og kobl fingeraftrykslæserens kabel fra I/O-kortet. Kobl møntcellebatteriets kabel fra I/O-kortet. Fjern skruen (M2x3), der fastgør I/O-kortet til håndledsstøtte- og tastaturmodulet.
Trin 1. 2. 3. 4. 5. 6. 7. 8. 9. Skub I/O-kortet ind i slottene på håndledsstøtte- og tastaturmodulet. Juster skruehullet på I/O-kortet med skruehullet på håndledsstøtte- og tastaturmodulet. Genmonter skruen (M2x3), der fastgør I/O-kortet til håndledsstøtte- og tastaturmodulet. Forbind I/O-kortets kabel til stikket på I/O-kortet, og luk låsen for at fastgøre kablet. Påsæt tapen, der fastgør I/O-kortkablet til I/O-kortet.
Om denne opgave Følgende billede angiver placeringen af tænd/sluk-knappen med fingeraftrykslæser og giver en visuel fremstilling af fjernelsesproceduren. Trin 1. 2. 3. 4. 5. 6. 7. Fjern de to skruer (M2x3), der fastgør tænd/sluk-knappens bøjle til håndledsstøtte- og tastaturmodulet. Løft tænd/sluk-knappens bøjle af håndledsstøtte- og tastaturmodulet. Pil tapen, der fastgør I/O-kortets kabel til I/O-kortet, af. Åbn låsen, og kobl I/O-kortets kabel fra I/O-kortet.
Trin 1. 2. 3. 4. 5. 6. 7. Juster tænd/sluk-knappen med dens kabel, og placer den i slotten på håndledsstøtte- og tastaturmodulet. Skub tænd/sluk-knappens kabel ind i stikket på fingeraftrykslæseren, og luk låsen for at fastgøre kablet. Forbind fingeraftrykslæserens kabel til stikket på I/O-kortet, og luk låsen for at fastgøre kablet. Forbind I/O-kortets kabel til stikket på I/O-kortet, og luk låsen for at fastgøre kablet. Påsæt tapen, der fastgør I/O-kortkablet til I/O-kortet.
Sådan fjernes og installeres komponenter
Trin 1. 2. 3. 4. 5. Pil tapen, der fastgør skærmkablet til systemkortet, af. Åbn låsen, og kobl skærmkablet fra systemkortet. Fjern de to skruer (M2,5x5), der fastgør de venstre skærmhængslet til håndledsstøtte- og tastaturmodulet. Fjern de tre skruer (M2,5x5), der fastgør de højre skærmhængsler til håndledsstøtte- og tastaturmodulet. Løft skærmmodulet i en vinkel, og fjern det fra håndledsstøtte- og tastaturmodulet.
Sådan monteres skærmmodulet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Følgende billede angiver placeringen af skærmmodulet og giver en visuel fremstilling af installationsproceduren.
Trin 1. 2. 3. 4. 5. Skub skærmmodulet i en vinkel, og placer det på håndledsstøtte- og tastaturmodulet. Genmonter de to skruer (M2,5x5), der fastgør det venstre skærmhængsel til håndledsstøtte- og tastaturmodulet. Genmonter de tre skruer (M2,5x5), der fastgør det højre skærmhængsel til håndledsstøtte- og tastaturmoduletForbind skærmkablets stik til systemkortet, og luk låsen for at fastgøre kablet. Påsæt tapen, der fastgør skærmkablet til systemkortet. Næste trin 1. Monter bunddækslet. 2.
2. 3. 4. 5. 6. 7. Fjern bunddækslet. Fjern batteriet. Fjern møntcellebatteriet. Fjern hukommelsesmodulerne. Fjern M.2 2230-solid state-drevet eller M.2 2280-solid state-drevet, alt efter hvilket der er relevant. Fjern varmelegemet. Om denne opgave Det følgende billeder angiver placeringen af stikkene på systemkortet. Figur 1. Stik på systemkortet 1. 3. 5. 7. Strømadapterportens kabel Blæserkabel Højtalerkabel Tastaturkabel 2. 4. 6. 8.
Trin 1. 2. 3. 4. 5. Fjern de tre skruer (M2,5x5), der fastgør det højre skærmhængsel til håndledsstøtte- og tastaturmodulet Åbn hængslet i en vinkel på 90 grader. Pil tapen, der fastgør USB Type-C-portens beslag til systemkortet, af. Kobl blæserkablet fra systemkortet. Pil tapen, der fastgør I/O-kortkablet til systemkortet, af.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Åbn låsen, og kobl I/O-kortets kabel fra systemkortet. Kobl højtalerkablet fra systemkortet. Åbn låsen, og kobl pegefeltets kabel fra systemkortet. Åbn låsen, og kobl tastaturets kabel fra systemkortet. Fjern de to skruer (M2x3), der fastgør USB Type-C-portens beslag til systemkortet. Løft USB Type-C-portens beslag af håndledsstøtte- og tastaturmodulet. Kobl strømadapterportens kabel fra systemkortet. Pil tapen, der fastgør skærmkablet til systemkortet, af.
Trin 1. 2. 3. 4. 5. Få systemkortet til at flugte, og placer det på håndledsstøtte- og tastaturmodulet. Genmonter de to skruer (M2x2), der fastgør systemkortet til håndledsstøtte- og tastaturmodulet. Forbind skærmkablet til stikket på systemkortet, og luk låsen for at fastgøre kablet. Påsæt tapen, der fastgør skærmkablet til systemkortet. Slut strømadapterportens kabel til stikket på systemkortet.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Ret skruehullerne på USB Type-C-portens beslag ind efter skruehullerne på systemkortet. Påsæt tapen, der fastgør USB Type-C-portens beslag til systemkortet. Genmonter de to skruer (M2x3), der fastgør USB Type-C-portens beslag på systemkortet. Skub tastaturkablet ind i stikket på systemkortet, og luk låsen for at fastgøre kablet. Skub pegefeltkablet ind i stikket på systemkortet, og luk låsen for at fastgøre kablet. Slut højtalerkablet til systemkortet.
Trin Når du har udført de indledende trin, står du tilbage med håndledsstøtte- og tastaturmodulet. Sådan monteres håndledsstøtte- og tastaturmodulet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Følgende billede angiver placeringen af håndledsstøtte- og tastaturmodulet og giver en visuel fremstilling af monteringsproceduren.
Trin Placer håndledsstøtte- og tastaturmodulet på en ren og flad overflade. Næste trin 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 52 Monter systemkortet. Monter skærmmodulet. Monter tænd/sluk-knappens kort. Monter pegefeltet. Monter strømadapterporten. Monter blæseren. Monter varmelegemet. Monter højttalerne. Monter I/O-kortet. Monter M.2 2230-solid state-drevet eller M.2 2280-solid state-drevet, alt efter hvilket der er relevant. Monter hukommelsesmodulerne. Monter møntcellebatteriet.
3 Drivere og downloads Når du retter fejl, henter eller installerer drivere, anbefaler vi, at du læser Dell Knowledge Based-artiklen Ofte stillede spørgsmål om drivere og downloads SLN128938.
4 Systemopsætning FORSIGTIG: Medmindre du er en erfaren computerbruger, skal du undlade at ændre indstillingerne for dette program. Visse ændringer kan medføre, at computeren ikke fungerer korrekt. BEMÆRK: Afhængigt af computeren og de installerede enheder er det muligvis ikke alle elementer i dette afsnit, der vises. BEMÆRK: Før du ændrer BIOS opsætningsprogram, anbefales det, at du skriver BIOS-opsætningens skærminformationer ned til fremtidig brug.
• Fremkalde menuen til engangsopstart ved tryk på tasten F12 Engangsopstartens menu viser de enheder, som du kan starte fra, herunder diagnostiske indstillinger. Opstartsmenuens valgmuligheder er: • • Udtageligt drev (hvis tilgængelig) STXXXX-drev (hvis tilgængeligt) BEMÆRK: XXX-betegner SATA-drevnummeret. • • • Optisk drev (hvis tilgængelig) SATA-harddisk (hvis tilgængelig) Diagnosticering Startrækkefølgeskærmen viser også muligheden for at få adgang til skærmen System Setup (systemopsætning).
Tabel 3. Systeminstallationsindstillinger – menuen Systemoplysninger (fortsat) Oversigt PROCESSOR Processortype Viser processortypen. Maksimum clockhastighed Viser processorens højeste clockhastighed. Minimum clockhastighed Viser processorens laveste clockhastighed. Aktuel clockhastighed Viser processorens aktuelle clockhastighed. Antal kerner Viser antallet af kerner i processoren. Processor ID Viser processorens identifikationskode.
Tabel 4. Systeminstallationsindstillinger – menuen Startkonfiguration (fortsat) Startkonfiguration Advanced Boot Options Aktivér UEFI-netværksstak Aktiverer eller deaktiverer UEFI-netværksstack. Standard: Slået til UEFI Boot Path Security Aktiverer eller deaktiverer, om systemet skal bede brugeren om at indtaste administratoradgangskoden ved start fra en UEFI-startsti via F12-startmenuen. Standard: Altid, undtagen intern HDD Tabel 5.
Tabel 5. Systeminstallationsindstillinger – menuen Systemkonfiguration (fortsat) Systemkonfiguration Aktivér Thunderbolt-præopstartsmoduler (og Aktivérer eller deaktiverer for at tillade eller fjerne tilladelse til, at PCIe-enheder kan PCIe bag TBT) tilsluttes via en Thunderbolt-adapter før opstart. Standard: Slået fra Diverse enheder Aktiverer eller deaktiverer forskellige indbyggede enheder. Enable Camera (Aktiver kamera) Aktiverer eller deaktiverer kameraet.
Tabel 7. Systeminstallationsindstillinger – menuen Sikkerhed (fortsat) Sikkerhed Enable Non-Admin Password Changes Tillader eller forhindrer brugeren i at ændre adgangskoden til systemet og harddiske uden behov for administratoradgangskode. Standard: Slået til Non-Admin Setup Changes UEFI Capsule Firmware Updates (Aktivér UEFI Capsule-opdatering af firmware) Aktiverer eller deaktiverer BIOS-opdateringer gennem UEFI capsuleopdateringspakker.
Tabel 7. Systeminstallationsindstillinger – menuen Sikkerhed (fortsat) Sikkerhed Intel SGX Aktiverer eller deaktiverer, om Intel Software Guard Extensions (SGX) skal lave et sikret miljø til at køre kode/lagre følsomme oplysninger. Standard: software-styret Tabel 8. Systeminstallationsindstillinger – menuen Adgangskoder Adgangskoder Enable Strong Passwords Aktiverer eller deaktiverer stærke adgangskoder. Standard: Slået fra Konfiguration af adgangskode Administratoradgangskode min.
Tabel 10. Systeminstallationsindstillinger – menuen Ekspertnøglestyring (fortsat) Ekspertnøglestyring Standard: PK Tabel 11. Systeminstallationsindstillinger – menuen Ydeevne Ydeevne Multi Core Support Aktive kerner Ændrer antallet af tilgængelige CPU-kerner for operativsystemet. Standardværdien er indstillet til det maksimale antal kerner.
Tabel 12. Systeminstallationsindstillinger – menuen Strømstyring (fortsat) Strømstyring Standard: Adaptive (Adaptiv). Batteriindstillinger optimeres adaptivt baseret på dit typiske brugsmønster af batteriet. Enable Advanced Battery Charge Configuration Aktiverer Advanced Battery Charge Configuration fra begyndelsen af dagen i en specifik arbejdsperiode. Advanced Battery Charged maksimerer batteriets sundhed, mens krævende brug stadig understøttes i løbet af arbejdsdagen.
Tabel 14. Systeminstallationsindstillinger – menuen POST-adfærd (fortsat) POST-adfærd BEMÆRK: Fejl, der anses for at være kritiske for computerens hardware, vil altid standse computeren. Enable Adapter Warnings Aktiverer eller deaktiverer computerens visning af advarselsmeddelelser om adaptere, når adaptere med for lidt strømkapacitet registreres. Standard: Slået til Aktivér Dock-advarselsmeddelelser. Aktiverer eller deaktiverer Dock-advarselsmeddelelser.
Tabel 16. Systeminstallationsindstillinger – menuen Vedligeholdelse (fortsat) Vedligeholdelse BIOS-gendannelse fra harddisk Lader computeren blive gendannet fra en dårlig BIOS-afbildning, så længe Boot Block-andelen er intakt og fungerer. Standard: Slået til BEMÆRK: BIOS-gendannelse er designet til at løse den primære BIOSblok, og kan ikke fungere, hvis den Boot Block er beskadiget. Desuden kan funktionen ikke virke i tilfælde af EC-forvanskning, ME-forvanskning eller et hardware-relateret problem.
Tabel 18. Systeminstallationsindstillinger – menuen SupportAssist (fortsat) SupportAssist Standard: Slået til Rydning af CMOS-indstillinger Om denne opgave FORSIGTIG: Rydning af CMOS-indstillinger nulstiller BIOS-indstillingerne på din computer. Trin 1. Sluk for computeren. 2. Fjern bunddækslet. BEMÆRK: Batteriet skal fjernes fra systemkortet (se trin 4 i Sådan fjernes bunddækslet). 3. Tryk og hold tænd/sluk-knappen nede i ca. 15 sekunder for at dræne den tilbageværende reststrøm. 4.
5 Fejlfinding SupportAssist-diagnosticering Om denne opgave SupportAssist-diagnosticering (tidligere kendt som ePSA-diagnosticering) foretager en fuldstændig kontrol af din hardware. SupportAssist-diagnosticering er indlejret i og startes internt af BIOS. SupportAssist-diagnosticering giver en række muligheder til særlige enheder eller enhedsgrupper.
Tabel 20.
7. Klik på Download (Hent) for at hente den seneste BIOS-version til computeren. 8. Efter hentning er afsluttet, naviger til mappen hvor du gemte BIOS-opdateringsfilen. 9. Dobbeltklik på BIOS-opdateringsfilens ikon og følg vejledningen på skærmen. Inddækning BIOS (USB-nøgle) Trin 1. 2. 3. 4. 5. 6. 7. 8. Følg proceduren fra trin 1 til trin 7 i "Flashing af BIOS" for at downloade den nyeste fil til BIOS-opsætningsprogrammet. Opret et USB-drev, der kan bootstartes.
4. Monter bunddækslet. 5.
6 Rekvirere hjælp og kontakte Dell Selvhjælpsressourcer Du kan få oplysninger og hjælp til Dell-produkter og servicer ved at bruge disse selvhjælpsressourcer: Tabel 21. Selvhjælpsressourcer Selvhjælpsressourcer Ressourceplacering Information om Dells produkter og services www.dell.com Mit Dell Tips Kontakt supporten Indtast Contact Support i en Windows-søgning, og tryk på Enter. Online-hjælp til operativsystem www.dell.com/support/windows www.dell.