Inspiron 15 5515 Servicehandbok Regleringsmodell: P106F Regleringstyp: P106F003 Mars 2021 Rev.
Anmärkningar, försiktighetsbeaktanden och varningar OBS: OBS innehåller viktig information som hjälper dig att få ut det mesta av produkten. CAUTION: VIKTIGT anger antingen risk för skada på maskinvara eller förlust av data och förklarar hur du kan undvika problemet. VARNING: En VARNING visar på en potentiell risk för egendoms-, personskador eller dödsfall. © 2021 Dell Inc. eller dess dotterbolag. Med ensamrätt. Dell, EMC och andra varumärken är varumärken som tillhör Dell Inc. eller dess dotterbolag.
Innehåll Kapitel 1: Arbeta inuti datorn............................................................................................................6 Innan du arbetar inuti datorn................................................................................................................................................6 Säkerhetsanvisningar............................................................................................................................................................
Ta bort knappcellsbatteriet.......................................................................................................................................... 36 Installera knappcellsbatteriet........................................................................................................................................ 37 Kylfläns.....................................................................................................................................................................
WiFi-cykel............................................................................................................................................................................. 74 Dränering av kvarvarande ström (utför maskinvaruåterställning)................................................................................ 75 Kapitel 6: Få hjälp och kontakta Dell................................................................................................
1 Arbeta inuti datorn Innan du arbetar inuti datorn Om denna uppgift OBS: Bilderna i det här dokumentet kan skilja från din dator beroende på konfigurationen du beställde. Steg 1. Spara och stäng alla öppna filer samt avsluta alla öppna program. 2. Stäng av datorn. Klicka på Start > Stänga > av strömmen. OBS: Om du använder ett annat operativsystem finns det anvisningar för hur du stänger av datorn i operativsystemets dokumentation. 3. Koppla bort datorn och alla anslutna enheter från eluttagen. 4.
CAUTION: Tryck in och mata ut eventuella kort från mediekortläsaren. OBS: Färgen på datorn och vissa komponenter kan skilja sig från de som visas i det här dokumentet. Policy om exponering mot strålning Enheten uppfyller myndighetskraven för exponering av radiovågor. Enheten är utformad och tillverkad så att den inte överstiger gränsvärdena för energi i radiofrekvensnivå (RF) som har fastställts av Federal Communications Commission (FCC) i USA:s regering.
● Antistatisk matta - Den antistatiska mattan är dissipativ och delar kan placeras på den under serviceförfaranden. När du använder en antistatisk matta din handledsrem ska sitta åt och jordningstråden ska kopplas till mattan och till någon omålad metall på systemet som du arbetar på. När den har anslutits ordentligt kan reservdelar tas ut från ESD-påsen och placeras direkt på mattan. ESD-känsliga artiklar är säkra i din hand, på ESD-mattan, i systemet eller inne i en påse.
4. Anslut datorn och alla anslutna enheter till eluttagen. 5. Starta datorn.
2 Ta bort och installera komponenter OBS: Bilderna i det här dokumentet kan skilja från din dator beroende på konfigurationen du beställde. Rekommenderade verktyg Procedurerna i detta dokument kan kräva att följande verktyg används: ● Krysspårmejsel (Phillips), nr 0 ● Plastrits Skruvlista OBS: När du tar bort skruvarna från en komponent rekommenderar vi att du noterar skruvtyp, antal skruvar och placerar dem i en skruvförvaringslåda.
Tabell 1. Skruvlista Komponent Skruvtyp Kvantitet Strömbrytare med fingeravtrycksläsare M2x3 1 I/O-kort M2x3 1 Styrplatta M1,6x2 3 Styrplatta M2x1,8 2 Nätaggregatsport M2,5x4 2 Bildskärmsgångjärn M2,5x4 6 Skruvbild Huvudkomponenter i Inspiron 15 5515 Följande bild visar huvudkomponenterna för Inspiron 15 5515.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Baskåpa Kylfläns Moderkort Minne Batteri Höger högtalare Handledsstöds- och tangentbordsmontering Styrplatta Bildskärmsmontering Knappcellsbatteri I/O-kort M.2 2280 SSD-disk, om installerad Trådlöst kort M.
16. Fläkt 17. Nätaggregatsport OBS: Dell innehåller en lista över komponenter och tillhörande artikelnummer för den ursprungliga systemkonfigurationen som köpts. Dessa delar är tillgängliga enligt garantitäckningar som kunden har köpt. Kontakta din Dell-säljare för köpalternativ. Kåpan Ta bort baskåpan Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. Om denna uppgift Följande bilder anger placeringen av baslocket och ger en visuell representation av borttagningsförfarandet.
Steg 1. Lossa de två (M2x7,75) fästskruvarna som håller fast baskåpan i handledsstöds- och tangentbordsenheten. 2. Ta bort de sju (M2x4) skruvarna som håller fast kåpan i handledsstöds- och tangentbordsmonteringen. 3. Använd en plastrits för att bända baskåpan vid sidan av bildskärmsenhetens gångjärn och fortsätt att arbeta på sidorna för att öppna baskåpan. 4. Lyft av baskåpan från handledsstöds- och tangentbordsmonteringen. 5.
6. Koppla bort batterikabeln från moderkortet. 7. Tryck och håll strömbrytaren intryckt i 20 sekunder för att jorda datorn och tömma den kvarvarande strömmen. Installera baskåpan Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Följande bild anger placeringen av baslocket och ger en visuell representation av intstallationsförfarandet.
Steg 1. Anslut batterikabeln till moderkortet. 2. Fäst tejpen för fästa batterikabeln. 3. Placera baskåpan på handledstöds- och tangentbordsmonteringen. 4. Rikta in skruvhålen på kåpan med skruvhålen i handledsstöds- och tangentbordsmonteringen och fäst sedan fast baskåpan på plats. 5. Dra åt de två (M2x7,75) fästskruvarna som håller fast baskåpan i handledsstöds- och tangentbordsenheten. 6. Sätt tillbaka de sju (M2x4) skruvarna som håller fast kåpan i handledsstöds- och tangentbordsmonteringen.
● Tryck inte på batteriets yta. ● Böj inte batteriet. ● Använd inte verktyg av något slag för att bända på eller mot batteriet. ● Se till att inga skruvar för denna produkt går förlorade under service eller felplaceras för att förhindra oavsiktlig punktering eller skada på batteriet och andra systemkomponenter. ● Om batteriet sitter fast i datorn på grund av svullnad, försök inte frigöra det som punktering, böjning eller krossning av ett litiumjonbatteri kan vara farligt.
Om denna uppgift Följande bild visar platsen för 3-cellsbatteriet (41 Wh) och ger en visuell representation av installationsproceduren. Steg 1. Med hjälp av justeringsstolparna placerar du 3-cellsbatteriet på handledsstöds- och tangentbordsenheten. 2. Rikta in skruvhålen på 3-cellsbatteriet mot skruvhålen på handledsstöds- och tangentbordsenheten. 3. Sätt tillbaka de tre (M2x3) skruvarna som fäster 3-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Anslut batterikabeln till moderkortet. 5.
Steg 1. Dra bort bandet som håller fast batterikabeln på moderkortet. 2. Koppla bort batterikabeln från moderkortet. 3. Ta bort de fyra (M2x3) skruvarna som fäster 4-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Lyft upp 4-cellsbatteriet och dess kabel , från handledsstöds- och tangentbordsenheten. Installera 4-cellsbatteriet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Steg 1. Med hjälp av justeringsstolparna placerar du 4-cellsbatteriet på handledsstöds- och tangentbordsenheten. 2. Rikta in skruvhålen på 4-cellsbatteriet mot skruvhålen på handledsstöds- och tangentbordsenheten. 3. Sätt tillbaka de fyra (M2x3) skruvarna som fäster 4-cellsbatteriet på handledsstöds- och tangentbordsenheten. 4. Anslut batterikabeln till moderkortet. 5. Sätt fast tejpen som håller fast batterikabeln på moderkortet. Nästa Steg 1. Installera baskåpan. 2.
Steg 1. Vänd på batteriet och ta bort batterikabeln från kabelhållarna på batteriet. 2. Koppla bort batterikabeln från kontakten på batteriet. 3. Lyft bort batterikabeln från batteriet. Installera batterikabeln Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Följande bild visar placeringen av batterikabeln och ger en visuell representation av installationsproceduren.
Steg 1. Justera och placera batterikabeln på batteriet. 2. Dra kabeln för batteriet genom kabelhållarna på batteriet. 3. Anslut batterikabeln till kontakten på batteriet. Nästa Steg 1. Installera 3-cellsbatteriet eller 4-cellsbatteriet, beroende på vilket som gäller. 2. Installera baskåpan. 3. Följ anvisningarna i När du har arbetat på datorn. Minnesmodulen Ta bort minnesmodulen Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
Steg 1. Lyft bort mylartejpen för att komma åt minnesmodulen. 2. Använd fingertopparna för att dra bort låsklämmorna från båda sidor av minnesmodulen tills minnesmodulen hoppar upp. 3. Ta bort minnesmodulen från minnesmodulkortplatsen. OBS: Upprepa steg 1 till 3 för att ta bort andra minnesmoduler installerade i datorn. Installera minnesmodulen Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Steg 1. Lyft bort mylartejpen för att komma åt minnesmodulkortplatsen. 2. Rikta in spåret på minnesmodulen med fliken på minnesmodulplatsen. 3. Skjut minnesmodulen ordentligt i en vinkel in i minnesmodulplatsen. 4. Tryck minnesmodulen nedåt tills den klickar på plats. OBS: Om du inte hör något klick tar du bort minnesmodulen och försöker igen. OBS: Upprepa steg 1 till 4 för att installera andra minnesmoduler i datorn. Nästa Steg 1. Installera baskåpan. 2.
SSD-disk – M.2-kortplats nr ett Ta bort 2230-SSD-disken från M.2-kortplats nr ett Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. OBS: SSD-diskar är ömtåliga. Var försiktig när du hanterar SSD-disken. OBS: Undvik dataförlust genom att inte ta bort SSD-disken medan datorn är i strömsparläge eller är påslagen. 2. Ta bort baskåpan. Om denna uppgift OBS: Beroende på vilken konfiguration som beställts kan datorn ha stöd för en 2230-SSD-disk eller en 2280-SSD-disk på M.2kortplats nr ett.
Om denna uppgift OBS: SSD-diskar är ömtåliga. Var försiktig när du hanterar SSD-disken. OBS: Beroende på vilken konfiguration som beställts kan datorn ha stöd för en 2230-SSD-disk eller en 2280-SSD-disk på M.2kortplats nr ett. OBS: Den här proceduren gäller endast om du installerar en 2230-SSD-disk på M.2-kortplats nr ett. OBS: Innan du installerar din 2230- eller 2280-SSD-disk ska du kontrollera att monteringsfästet sitter på rätt plats. Mer information finns i Installera SSD-diskens monteringsfäste.
Om denna uppgift OBS: Beroende på vilken konfiguration som beställts kan datorn ha stöd för en 2280-SSD-disk eller en 2230-SSD-disk på M.2kortplats nr ett. OBS: Den här proceduren gäller bara för datorer som levereras med en 2280-SSD-disk installerad på M.2-kortplats nr ett. Följande bild visar placeringen av 2280-SSD-disken som installerats på M.2-kortplats nr ett, och ger en visuell representation av borttagningsproceduren. Steg 1.
Steg 1. Rikta in spåret på 2280 SSD-disken med fliken på kortplatsen för SSD-disken. 2. För in 2280 SSD-disken ordentligt i kortplatsen för SSD-disken vid en vinkel. 3. Rikta in skruvhålet på SSD-disken med skruvhålet på handledsstöds- och tangentbordsenheten. 4. Sätt tillbaka skruven (M2x3) som fäster 2280-SSD-disken vid handledsstöds- och tangentbordsenheten. Nästa Steg 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Installera SSD-diskens monteringsfäste på M.
Steg 1. Skjut och ta bort SSD-diskens monteringsfäste från monteringsfästets plats på handledsstöds- och tangentbordsmonteringen. 2. Vrid på SSD-diskens monteringsfäste 180 grader. 3. Skjut in SSD-diskens monteringsfäste i monteringsplatsen på handledsstöds- och tangentbordsmonteringen. 4. Installera 2230-SSD-disken eller 2280-SSD-disken, beroende på vilket som gäller. SSD-disk – M.2-kortplats nr två Ta bort 2230-SSD-disken från M.2-kortplats nr två Förutsättningar OBS: M.
Steg 1. Ta bort skruven (M2x3) som håller fast det termiska skyddet för SSD-disken och SSD-disken i handledsstöds- och tangentbordsmonteringen. 2. Skjut ut och lyft bort SSD-diskens värmeskydd från SSD-disken. 3. Skjut och ta bort SSD-disken från M.2-kortplats två. Installera 2230-SSD-disken i M.2-kortplats nr två Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Om denna uppgift OBS: SSD-diskar är ömtåliga. Var försiktig när du hanterar SSD-disken. OBS: M.2-plats två stöder endast 2230 SSD-disk. OBS: Den här proceduren gäller bara för datorer som levereras med en 2230-SSD-disk installerad på M.2-kortplats nr två. Den följande bilden visar placeringen av 2230-SSD-disken som installerats på M.2-kortplats nr två, och ger en visuell representation av installationsproceduren. Steg 1. Rikta in spåret på 2230-SSD-disken med fliken på M.2-kortplats nr två på moderkortet.
4. Rikta in skruvhålet på SSD-diskens värmeskydd med skruvhålet på handledsstöds- och tangentbordsenheten. 5. Sätt tillbaka skruven (M2x3) som håller fast det termiska skyddet för SSD-disken och SSD-disken i handledsstöds- och tangentbordsmonteringen. Nästa Steg 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Trådlöst kort Ta bort det trådlösa kortet Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
Steg 1. Ta bort skruven (M2x4) som håller fast fästet för det trådlösa kortet på det trådlösa kortet och moderkortet. 2. Ta bort fästet för det trådlösa kortet från det trådlösa kortet. 3. Koppla bort antennkablarna från det trådlösa kortet. 4. Skjut ut det trådlösa kortet och avlägsna det från platsen för det trådlösa kortet. Installera det trådlösa kortet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren.
Steg 1. Anslut antennkablarna till det trådlösa kortet. Följande tabell visar färgschemat för antennkablarna för de kort för trådlös teknik som stöds av datorn. Tabell 2. Färgschema för antennkablar Kontakter på det trådlösa kortet Färg på antennkabel Silkscreen-märkning Main (huvudmeny) Vit MAIN (huvudmeny) △ (vit triangel) Sekundär Svart AUX ▲ (svart triangel) 2. Rikta in spåret på det trådlösa kortet med fliken på kortplatsen för det trådlösa kortet på moderkortet. 3.
Fläkt Ta bort fläkten Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Om denna uppgift Följande bild visar fläktens placering och ger en visuell representation av borttagningsproceduren. Steg 1. Koppla bort fläktkabeln från moderkortet. 2. Ta bort de två skruvarna (M2x3) som fäster fläkten i handledsstöds- och tangentbordsenheten. 3. Lyft av fläkten från handledsstöds- och tangentbordsmonteringen.
Steg 1. Med hjälp av justeringsstolparna placerar du fläkten på handledsstöds- och tangentbordsenheten. 2. Sätt tillbaka de två (M2x3) skruvarna för att fästa fläkten på handledsstöds- och tangentbordsenheten. 3. Anslut fläktkabeln till moderkortet. Nästa Steg 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Knappcellsbatteri Ta bort knappcellsbatteriet Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn.
Steg 1. Koppla bort kabeln för knappcellsbatteriet från I/O-kortet. 2. Dra bort knappcellsbatteriet från handledsstöds- och tangentbordsenheten. Installera knappcellsbatteriet Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Följande bild visar platsen för knappcellsbatteriet och ger en visuell representation av installationsproceduren.
Steg 1. Fäst knappcellsbatteriet till kortplatsen på handledsstöds- och tangentbordsmonteringen. 2. Anslut knappcellsbatterikabeln till I/O-kortet. Nästa Steg 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. Kylfläns Ta bort kylflänsen Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. CAUTION: För att processorn ska kylas maximalt bör du inte röra vid kylflänsens värmeöverföringsytor.
Steg 1. Lossa de fyra fästskruvarna som fäster kylflänsen vid moderkortet i rätt ordning (anges på kylflänsen). 2. Lyft bort kylflänsen från moderkortet. Installera kylflänsen Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. CAUTION: Felaktig inriktning av kylflänsen kan orsaka skada på moderkortet och processorn.
Steg 1. Rikta in skruvhålen på kylflänsen mot skruvhålen på moderkortet. 2. Dra åt i rätt ordning (anges på kylflänsen) fyra fästskruvarna som håller fast kylflänsen i moderkortet. Nästa Steg 1. Installera baskåpan. 2. Följ anvisningarna i När du har arbetat inuti datorn. I/O-kort Ta bort I/O-kortet Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan.
Steg 1. Ta bort de tre (M2,5x4) skruvarna som fäster det vänstra bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. 2. Öppna bildskärmsgångjärnet i en vinkel på 90 grader. 3. Öppna spärren och koppla bort kortkabeln för strömbrytaren med den valfria fingeravtrycksläsarens kabel från I/O-kortet. 4. Koppla bort kabeln för knappcellsbatteriet från I/O-kortet. 5. Dra bort tejpen som håller fast kabeln för I/O-kortet i I/O-kortet. 6.
Steg 1. Skjut I/O-kortet i facken på handledsstöds- och tangentbordsenheten. 2. Rikta in skruvhålet på I/O-kortet med skruvhålet på handledsstöds- och tangentbordsmonteringen. 3. Sätt tillbaka skruven (M2x3) som håller fast I/O-kortet i handleds- och tangentbordsenheten. 4. Anslut strömbrytaren med den valfria fingeravtrycksläsarens kabel till kontakten på I/O-kortet och stäng spärren för att fästa kabeln. 5. Anslut knappcellsbatterikabeln till I/O-kortet. 6.
Steg 1. Öppna spärren och koppla bort kabeln till det bakgrundsbelysta tangentbordet, tangentbordskabeln och styrplattans kabel från moderkortet. 2. Observera hur högtalarkabeln är dragen och ta bort högtalarkabeln från kabelhållarna på handledsstöds- och tangentbordsmonteringen. 3. Dra av tejpen som håller fast högtalarkabeln i handledsstöds- och tangentbordsenheten. 4. Koppla bort högtalarkabeln från moderkortet. 5.
Om denna uppgift Följande bild visar var högtalaren är placerad och hur installationsproceduren går till. Steg 1. Använd justeringstapparna och gummitågringarna för att placera högtalarna i facken på handledsstöds- och tangentbordsmonteringen. 2. Anslut högtalarkabeln till moderkortet. 3. Dra högtalarkabeln genom kabelhållarna på handledsstöds- och tangentbordsmonteringen. 4.
Pekskärm Ta bort styrplattan Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. 3. Ta bort batteriet. Om denna uppgift Följande bilder visar styrplattans placering och ger en visuell representation av borttagningsproceduren. Steg 1. Öppna spärren och koppla ur styrplattans kabel från moderkortet. 2. Ta bort de tre skruvarna (M1.6x2) som håller fast styrplattans fäste i handledsstöds- och tangentbordsmonteringen. 3.
Steg 1. Skjut styrplattan in i luckan på handledsstöds- och tangentbordsenheten. OBS: Vänd på datorn och öppna skärmen. Kontrollera att styrplattan är lika justerad längs alla fyra sidor. 2. Sätt tillbaka de två skruvarna (M2x1,8) som håller fast styrplattan i handledsstöds- och tangentbordsmonteringen. 3. Fäst tejpen som håller fast styrplattan vid handledsstöds- och tangentbordsmonteringen. 4. Rikta in skruvhålen på styrplattan mot skruvhålen på handledsstöds- och tangentbordsmonteringen. 5.
Bildskärmsenhet Ta bort bildskärmsenheten Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. Om denna uppgift Följande bild visar var bildskärmsenheten är placerad och hur borttagningsproceduren går till.
Steg 1. Dra bort tejpen som håller fast bildskärmskabeln på moderkortet. 2. Öppna kontaktspärren och koppla ur bildskärmskabeln från moderkortet. 3. Ta bort de tre (M2,5x4) skruvarna som håller fast det vänstra displaygångjärnet på moderkortet. 4. Ta bort de tre (M2,5x4) skruvarna som håller fast det högra displaygångjärnet på moderkortet. 5. Öppna bildskärmsgångjärnen i en vinkel på 90 grader. 6. Skjut bort handledsstöds- och tangentbordsmonteringen från bildskärmsmonteringen.
Installera bildskärmsenheten Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Följande bild visar var bildskärmsmonteringen är placerad och hur installationsproceduren går till.
Steg 1. Skjut in bildskärmsenheten i en vinkel och placera bildskärmsenheten på handledsstöds- och tangentbordsenheten. 2. Med hjälp av justeringsposter, stäng bildskärms-gångjärnen. 3. Sätt tillbaka de tre (M2,5x4) skruvarna som håller fast det högra displaygångjärnet på moderkortet. 4. Sätt tillbaka de tre (M2,5x4) skruvarna som håller fast det vänstra displaygångjärnet på moderkortet. 5. Skjut in bildskärmskabeln i kontakten på moderkortet och stäng spärren så att kabeln sitter fast. 6.
Strömbrytare med fingeravtrycksläsare som tillval Ta bort strömbrytaren med valfri fingeravtrycksläsare Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn. 2. Ta bort baskåpan. 3. Ta bort I/O-kortet. Om denna uppgift Följande bild visar platsen för strömbrytaren med fingeravtrycksläsare som tillval och ger en visuell representation av borttagningsproceduren. Steg 1.
Steg 1. Justera och placera strömbrytaren med den valfria fingeravtrycksläsaren på handledsstöds- och tangentbordsenheten, 2. Sätt tillbaka skruven (M2x3) som håller fast strömbrytaren med valfri fingeravtrycksläsare i handledsstöds- och tangentbordsenheten. Nästa Steg 1. Installera I/O-kortet. 2. Installera baskåpan. 3. Följ anvisningarna i När du har arbetat inuti datorn. Moderkort Ta bort moderkortet Förutsättningar 1. Följ anvisningarna i Innan du arbetar inuti datorn.
5. 6. 7. 8. 9. Ta bort M.2 2280 SSD-disken eller M.2 2230 SSD-disken från M.2-kortplats ett, beroende på vilket som gäller. Ta bort M.2 2230 SSD-disken från M.2-kortplats två, om tillämpligt. Ta bort det trådlösa kortet. Ta bort fläkten. Ta bort kylflänsen. Om denna uppgift OBS: Moderkortet kan tas bort och installeras med kylflänsen monterad när du byter ut och sätter tillbaka andra delar för att förenkla proceduren och bevara den termiska förbindelsen mellan moderkortet och kylflänsen.
Ta bort och installera komponenter
Steg 1. Ta bort de tre (M2,5x4) skruvarna som fäster det högra bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. 2. Öppna det högra bildskärmsgångjärnet i en vinkel på 90 grader. 3. Dra bort tejpen som håller fast bildskärmskabeln på moderkortet. 4. Öppna kontaktspärren och koppla ur bildskärmskabeln från moderkortet. 5. Dra bort tejpen och koppla bort nätadapterportens kabel från moderkortet. 6. Ta bort de två (M2x4) skruvarna som fäster USB Type-C-fästet vid moderkortet. 7.
OBS: Alla ändringar du gjort i BIOS med BIOS-konfigurationsprogrammet tas bort om du byter ut moderkortet. Du måste göra de lämpliga ändringarna igen när du byter ut moderkortet. Följande bild visar kontakterna på moderkortet. Figur 2. Kontakter på moderkortet 1. 2. 3. 4. 5. 6. 7. 8. 9.
Ta bort och installera komponenter 57
Steg 1. Justera och placera moderkortet på handledsstöds- och tangentbordsenheten. 2. Sätt tillbaka de tre skruvarna (M2x2) som fäster moderkortet i handledsstöds- och tangentbordsenheten. 3. Anslut bildskärmskabeln till moderkortet och stäng haken så att kabeln sitter fast ordentligt. 4. Sätt fast tejpen som håller fast bildskärmskabeln på moderkortet. 5. Anslut kabeln för nätaggregatporten till moderkortet. 6. Fäst tejpen som håller fast kabeln till nätaggregatporten på moderkortet. 7.
13. Anslut kabeln för I/O-kortet från moderkortet. 14. Fäst tejpen som håller fast kabeln för I/O-kortet på moderkortet. 15. Stäng det högra bildskärmsgångjärnet. 16. Sätt tillbaka de tre (M2,5x4) skruvarna som fäster det högra - bildskärmsgångjärnet vid handledsstöds- och tangentbordsmonteringen. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. Installera kylflänsen. Installera fläkten. Installera trådlösa kortet. Installera M.2 2280 SSD-disken eller M.2 2230 SSD-disken i M.
2. Öppna bildskärmsgångjärnet i en vinkel på 90 grader. 3. Koppla bort kabeln för nätaggregatporten från moderkortet. 4. Dra bort tejpen som håller fast kabeln till nätaggregatsporten på moderkortet. 5. Ta bort kabeln för nätaggregatsporten från kabelhållarna på handledsstöds- och tangentbordsenheten. 6. Lyft av nätadapterporten tillsammans med kabeln från handledsstöds- och tangentbordsmonteringen.
Enhet med handledsstöd och tangentbord Ta bort handledsstöds- och tangentbordsmonteringen Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Följ anvisningarna i Innan du arbetar inuti datorn. Ta bort baskåpan. Ta bort 3-cellsbatteriet eller 4-cellsbatteriet, beroende på vilket som gäller. Ta bort minnesmodulen. Ta bort M.2 2280 SSD-disken eller M.2 2230 SSD-disken från M.2-kortplats ett, beroende på vilket som gäller. Ta bort M.2 2230 SSD-disken från M.2-kortplats två, om tillämpligt.
Installera handledsstöds- och tangentbordsmonteringen Förutsättningar Om du byter ut en komponent, ta bort den befintliga komponenten innan du utför installationsproceduren. Om denna uppgift Placera handledsstöds- och tangentbordsmonteringen på en plan yta.
Nästa Steg 1. 2. 3. 4. 5. 6. Installera bildskärmsmonteringen. Installera styrplattan. Installera högtalarna. Installera nätaggregatsporten. Installera strömbrytaren med fingeravtrycksläsare som tillval. Installera moderkortet. OBS: Moderkortet kan installeras tillsammans med kylflänsen. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Installera I/O-kortet. Installera fläkten. Installera knappcellsbatteriet. Installera trådlösa kortet. Installera M.2 2280 SSD-disken eller M.2 2230 SSD-disken i M.
3 Drivrutiner och hämtningsbara filer Vid felsökning, hämtning eller installation av drivrutiner rekommenderas läsning av Dells kunskapsartikel Vanliga frågor om drivrutiner och hämtningsbara filer SLN128938.
4 Systeminstallationsprogram CAUTION: Såvida du inte är en mycket kunnig datoranvändare bör du inte ändra inställningarna i BIOSinställningsprogrammet. Vissa ändringar kan medföra att datorn inte fungerar som den ska. OBS: Beroende på den här datorn och dess installerade enheter visas kanske inte alla objekt som beskrivs i det här avsnittet.
Engångsstartmenyn visar de enheter som du kan starta från inklusive diagnostikalternativet. Alternativen i startmenyn är följande: ● Borttagbar enhet (om sådan finns) ● STXXXX enhet (om sådan finns) OBS: XXX anger numret på SATA-enheten. ● Optisk enhet (om sådan finns) ● SATA-hårddisk (om sådan finns) ● Diagnostik Startsekvensskärmen visar även alternativet att öppna systeminstallationsskärmen.
Tabell 4. Systeminstallationsalternativ—Main (huvudmenyn) Main (huvudmeny) System Memory Visar total installerad minnesstorlek på datorn. Minneshastighet Visar minneshastigheten. Keyboard Type Visar tangentbordets typ (alternativet kan vara upplyst eller icke-upplyst). Tabell 5.
Tabell 5. Systeminstallationsalternativ – menyn Avancerat (fortsättning) Avancerat ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Mikrofon Här kan du slå på/stänga av mikrofonen. Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Camera (kamera) Här kan du slå på/stänga av kameran. Alternativen är: ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Internal Bluetooth Här kan du slå på/stänga av Bluetooth.
Tabell 5. Systeminstallationsalternativ – menyn Avancerat Avancerat ● Enabled (aktiverat) (standardinställning) ● Disabled (inaktiverat) Maintenance (underhåll) Datarensning vid nästa start BIOS Recovery from Hard Drive (BIOSåterställning från hårddisk) BIOS Auto Recovery SupportAssist-systemupplösning Underhållsinformation. Utför en datarensning vid nästa start.
Tabell 6. Systemkonfigurationsalternativ – Säkerhetsmenyn Security (säkerhet) Firmware TPM Aktivera eller inaktivera TPM 2.0-säkerhetsalternativ. TPM Security TPM 2.0-säkerhetsalternativ. TPM On (TPM På) PPI Bypass for Enable Commands (PPI förbigå för aktiverade kommandon) Slå på/stäng av TPM-säkerhetsalternativet. Alternativen är: ● På ● Off (av) Styr TPM Physical Presence Interface (PPI).
Tabell 7. Systeminstallationsalternativ—menyn Boot (start) Boot (start) OBS: Alternativet kan se annorlunda ut i operativsystemet Linux. File Browser Del Boot Option Windows Boot Manager (Windows starthanterare): Visar Dell-startsökvägen för standardstartalternativet. OBS: Alternativet kan se annorlunda ut i operativsystemet Linux. UEFI BOOT (UEFI-start) HDD1- Windows Boot Manager (Windows-starthanterare) Visar enhets-ID för den sekundära lagringen i datorn.
5 Felsökning SupportAssist-diagnostik Om denna uppgift SupportAssist-diagnostiken (tidigare kallad ePSA-diagnostik) utför en fullständig kontroll av din maskinvara. SupportAssist-diagnostiken är inbäddad i BIOS och lanseras av BIOS internt. SupportAssist-diagnostiken ger en rad alternativ för specifika enheter eller enhetsgrupper.
Tabell 9. Diagnostikindikatorkoder Blinkningsmönster Problembeskrivning 2 1 Kör verktyget Intel CPU diagnostics. Om problemet kvarstår, byt ut moderkortet. 2 2 Flasha senaste BIOSversionen. Om problemet kvarstår, byt ut moderkortet. 2 3 Bekräfta att minnesmodulen är korrekt installerad. Om problemet kvarstår, byt ut minnesmodulen. 2 4 Återställ och byt plats på minnesmodulerna. Om problemet kvarstår, byt ut minnesmodulen. 2 5 Återställ och byt plats på minnesmodulerna.
För mer information om Dell SupportAssist OS Recovery, se Dell SupportAssist OS Recovery User's Guide på www.dell.com/support. Flash-uppdatera BIOS Om denna uppgift Du kan vara tvungen att uppdatera BIOS när det finns en uppdatering eller när du bytt ut moderkortet. Följ dessa steg för att flasha BIOS: Steg 1. Starta datorn. 2. Gå till www.dell.com/support. 3. Klicka på Product Support (Produktsupport), ange servicenumret för din dator och klicka sedan på Submit (Skicka).
Steg 1. Stäng av datorn. 2. Stäng av modemet. 3. Stäng av den trådlösa routern. 4. Vänta 30 sekunder. 5. Slå på den trådlösa routern. 6. Slå på modemet. 7. Starta datorn. Dränering av kvarvarande ström (utför maskinvaruåterställning) Om denna uppgift Kvarvarande ström är den återstående statiska elektriciteten som finns kvar på datorn även efter att den har stängts av och batteriet har tagits bort.
6 Få hjälp och kontakta Dell Resurser för självhjälp Du kan få information och hjälp för Dell-produkter och tjänster med följande resurser för självhjälp: Tabell 10. Resurser för självhjälp Resurser för självhjälp Resursplats Information om Dell-produkter och tjänster www.dell.com My Dell-appen Tips Kontakta support I Windows skriver du Contact Support och trycker på retur. Onlinehjälp för operativsystemet www.dell.