Inspiron 13 7000 2-in-1 서비스 설명서 컴퓨터 모델: Inspiron 13-7373 규정 모델: P83G 규정 유형: P83G001
참고, 주의 및 경고 노트: "참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정 보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이 러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. Copyright © 2017 Dell Inc. 또는 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상표일 수 있습니다.
목차 컴퓨터 내부 작업을 시작하기 전에................................ 9 시작하기 전에 ......................................................................................... 9 안전 지침..................................................................................................9 권장 도구................................................................................................ 10 나사 목록................................................................................................ 10 컴퓨터 내부 작업을 마친 후에........................
코인 셀 배터리 장착.....................................................22 절차........................................................................................................ 22 작업후 필수 조건................................................................................... 22 방열판 분리................................................................. 23 필수 구성 요소....................................................................................... 23 절차..............................................................
전원 어댑터 포트 장착................................................. 34 절차........................................................................................................ 34 작업후 필수 조건................................................................................... 34 무선 카드 분리.............................................................35 필수 구성 요소....................................................................................... 35 절차...................................................................
솔리드 상태 드라이브 장착.......................................... 49 절차........................................................................................................ 49 작업후 필수 조건................................................................................... 49 시스템 보드 제거......................................................... 50 필수 구성 요소....................................................................................... 50 절차..........................................................................
키보드 장착................................................................. 66 절차........................................................................................................ 66 작업후 필수 조건....................................................................................67 손목 받침대 조립품 분리..............................................68 필수 구성 요소....................................................................................... 68 절차...................................................................
잊은 암호 삭제................................................................................. 88 문제 해결..................................................................... 89 BIOS 플래싱........................................................................................... 89 강화된 사전 부팅 시스템 평가(ePSA) 진단...........................................89 ePSA 진단 실행................................................................................90 진단.......................................................................
컴퓨터 내부 작업을 시작하기 전 에 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습 니다. 시작하기 전에 1 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2 컴퓨터를 종료하십시오. Start(시작) → 을 클릭합니다. Power(전원) → Shut down(종료) 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에 서 종료 지침을 참조하십시오. 3 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. 4 키보드, 마우스, 모니터 등과 같은 연결된 모든 네트워크 기기와 주변 장치를 컴퓨터에서 분리합니다. 5 해당하는 경우, 모든 미디어 카드 및 광학 디스크를 컴퓨터에서 분리합니다. 안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 경고: 컴퓨터 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어보십시오.
주의: 구성 요소 및 카드의 손상을 방지하려면 구성 요소 및 카드를 잡을 때 핀이나 단자를 잡지 말고 모서리를 잡습니다. 주의: Dell 기술 지원 팀에서 승인하거나 지시한 경우에만 문제 해결 및 수리 작업을 수행해야 합니다. Dell사에서 공인하지 않은 서비스로 인한 손상에 대 해서는 보상하지 않습니다. 제품과 함께 제공된 안전 지침 또는 www.dell.com/regulatory_compliance의 지침을 참조하십시오. 주의: 컴퓨터 내부의 부품을 만지기 전에 컴퓨터 뒷면 금속처럼 도색되지 않 은 금속 표면을 만져 접지하십시오. 작업하는 동안 컴퓨터의 도색되지 않은 금속 표면을 주기적으로 만져 내부 구성부품을 손상시킬 수 있는 정전기를 제거하십시오. 주의: 케이블을 분리할 때는 케이블을 직접 잡아 당기지 말고 커넥터나 당김 탭을 잡고 분리하십시오.
표 1. 나사 목록 구성 요소 고정 위치 나사 유형 수량 하단 덮개 손목 받침대 조 립품 M2.5x5 9 배터리 손목 받침대 조 립품 M2x3 4 팬 키보드 브래킷 M2x3 2 무선 카드 키보드 브래킷 M2x3 1 전원 어댑터 포 트 손목 받침대 조 립품 M2x3 1 디스플레이 조 립품 손목 받침대 조 립품 M2.5x5 6 I/O 보드 키보드 브래킷 M2x2 1 손목 받침대 조 립품 나사 이미지 1 SSD 키보드 브래킷 M2x3 1 Type-C 포트 브 래킷 시스템 보드 M2x3 1 터치패드 손목 받침대 조 립품 M2x2 4 시스템 보드 키보드 브래킷 M2x2 2 키보드 브래킷 키보드 손목 받 침대 조립품 M1.4x2 27 키보드 손목 받침대 조 립품 M1.2x1.
컴퓨터 내부 작업을 마친 후에 주의: 컴퓨터 내부에 나사가 남아 있거나 느슨한 나사가 존재하는 경우 컴퓨 터가 심각하게 손상될 수 있습니다. 1 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사가 없는지 확인합니다. 2 컴퓨터 작업을 시작하기 전에 분리한 모든 외부 장치, 주변 장치 및 케이블을 컴퓨터에 연결합니다. 3 컴퓨터 작업을 시작하기 전에 분리한 모든 미디어 카드, 디스크 및 기타 부품 을 다시 장착합니다. 4 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 5 컴퓨터를 켭니다.
베이스 덮개 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 베이스 덮개를 손목 받침대 조립품에 고정시키는 조임 나사를 풉니다. 2 베이스 덮개를 손목 받침대 조립품에 고정하는 9개의 나사(M2.5x5)를 제거합 니다. 3 플라스틱 스크라이브를 사용하여 손목 받침대 조립품에서 베이스 덮개를 들 어 올립니다.
4 베이스 덮개를 들어 올려 손목 받침대 조립품에서 분리합니다. 5 당김 탭을 사용하여 시스템 보드에서 배터리 케이블을 분리합니다.
6 컴퓨터를 뒤집고 디스플레이를 연 후 전원 버튼을 약 15초간 눌러 시스템 보드 를 접지시킵니다.
베이스 덮개 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 배터리 케이블을 시스템 보드에 연결합니다. 2 베이스 덮개의 탭을 손목 받침대 어셈블리의 슬롯에 맞추고 베이스 덮개를 제 자리에 끼웁니다. 3 베이스 덮개를 손목 받침대 조립품에 고정하는 9개의 나사(M2.5x5)를 장착합 니다. 4 베이스 덮개를 손목 받침대 조립품에 고정시키는 나사를 조입니다.
배터리 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 배터리의 라우팅 가이드에서 스피커 케이블을 분리합니다. 2 배터리를 손목 받침대 조립품에 고정하는 7개의 나사(M2x3)를 분리합니다.
3 18 배터리를 들어 올려 손목 받침대 조립품에서 분리합니다.
배터리 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 배터리의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니다. 2 배터리를 손목 받침대 조립품에 고정하는 4개의 나사(M2x3)를 장착합니다. 3 배터리의 라우팅 가이드를 통해 스피커 케이블을 배선합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
코인 셀 배터리 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 코인 셀 배터리를 분리하면 BIOS 설정 프로그램 설정을 기본값으로 재 설정합니다. 코인 셀 배터리를 제거하기 전에 BIOS 설정 프로그램 설정을 기 록하는 것이 좋습니다. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 20 I/O 보드에서 코인 셀 전지 케이블을 분리합니다.
2 키보드 브래킷에서 코인 셀 배터리를 떼어냅니다.
코인 셀 배터리 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 코인 셀 배터리를 키보드 브래킷에 부착합니다. 2 I/O 보드에 코인 셀 배터리 케이블을 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
방열판 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 경고: 방열판은 정상 작동 중에 뜨거워질 수 있습니다. 충분한 시간 동안 방 열판을 식힌 후에 만지도록 하십시오. 주의: 프로세서의 최대 냉각 기능을 보장하려면 프로세서 방열판의 열 전달 영역을 만지지 마십시오. 피부에 묻어있는 오일은 열 그리스의 열 전달 기능 을 저하시킬 수 있습니다. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 방열판 조립품에 표시된 번호 순서대로 방열판 조립품을 시스템 보드에 고정 하는 4개의 조임 나사를 분리합니다.
2 24 방열판을 들어 올려 시스템 보드에서 분리합니다.
방열판 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 방열판을 잘못 맞추면 시스템 보드 및 프로세서가 손상될 수 있습니다. 노트: 원래 시스템 보드 및 방열판을 함께 다시 설치할 경우 원래 열 그리스 를 다시 사용할 수 있습니다. 시스템 보드 또는 방열판을 장착할 경우 키트에 제공된 열 패드를 사용하여 열 전도성을 확보합니다. 절차 1 방열판의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 2 방열판 조립품에 표시된 번호 순서대로 방열판 조립품을 시스템 보드에 고정 하는 4개의 조임 나사를 장착합니다.
팬 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 시스템 보드에서 팬 케이블을 분리합니다. 2 팬의 라우팅 가이드에서 I/O 보드 케이블을 분리합니다. 3 팬을 키보드 브래킷에 고정하는 2개의 나사(M2x3)를 분리합니다.
4 키보드 브래킷에서 팬을 들어 분리합니다.
팬 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 팬의 나사 구멍을 키보드 브래킷의 나사 구멍에 맞춥니다. 2 팬을 키보드 브래킷에 고정시키는 2개의 나사(M2x3)를 장착합니다. 3 팬의 라우팅 가이드를 통해 I/O 보드 케이블을 배선합니다. 4 팬 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
스피커 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 시스템 보드에서 스피커 케이블을 분리합니다. 2 왼쪽 스피커를 들어 올려 손목 받침대 조립품에서 분리합니다. 3 배터리의 라우팅 가이드에서 스피커 케이블을 분리합니다. 4 스피커 케이블을 손목 받침대 조립품에 고정시키는 테이프를 떼어냅니다.
5 30 오른쪽 스피커를 들어 올려 손목 받침대 조립품에서 분리합니다.
스피커 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 정렬 포스트를 사용하여 오른쪽 스피커를 손목 받침대 조립품에 맞추어 놓습 니다. 2 스피커 케이블을 손목 받침대 조립품에 고정시키는 테이프를 부착합니다. 3 배터리의 라우팅 가이드를 통해 스피커 케이블을 배선합니다. 4 정렬 포스트를 사용하여 왼쪽 스피커를 손목 받침대 조립품에 맞추어 놓습니 다. 5 시스템 보드에 스피커 케이블을 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
전원 어댑터 포트 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 시스템 보드에서 전원 어댑터 포트 케이블을 분리합니다. 2 전원 어댑터 포트를 손목 받침대 조립품에 고정하는 나사(M2x3)를 분리합니 다.
3 전원 어댑터 포트를 손목 받침대 조립품에서 들어 올려 분리합니다.
전원 어댑터 포트 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 전원 어댑터 포트를 손목 받침대 조립품의 슬롯에 삽입합니다. 2 전원 어댑터 포트를 손목 받침대 조립품에 고정하는 나사(M2x3)를 장착합니 다. 3 전원 어댑터 포트 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
무선 카드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 I/O 보드에서 무선 카드를 찾은 다음 무선 카드에서 마일라를 들어 올립니다. 2 무선 카드 브래킷과 무선 카드를 키보드 브래킷에 고정시키는 나사(M2x3)를 분리합니다. 3 무선 카드 브래킷을 무선 카드에서 들어 올립니다.
4 무선 카드에서 안테나 케이블을 분리합니다. 5 무선 카드를 밀어 I/O 보드에서 분리합니다.
무선 카드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 주의: 무선 카드의 손상을 방지하려면 카드 아래에 케이블을 올려 놓지 마십 시오. 1 마일라를 들어 올려 무선 카드 슬롯에 액세스합니다. 2 무선 카드의 노치를 무선 카드 슬롯의 탭에 맞춘 후 무선 카드를 일정한 각도 로 무선 카드 슬롯으로 삽입합니다. 3 무선 카드에 안테나 케이블을 연결합니다. 다음 표에는 컴퓨터에서 지원되는 무선 카드의 안테나 케이블 색상표가 제공 됩니다. 표 2.
5 무선 카드를 키보드 브래킷에 고정시키는 나사(M2x3)를 장착합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
디스플레이 조립품 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드 분리의 1단계부터 4단계 절차를 수행합니다. 절차 1 손목 받침대 조립품의 배선 가이드에서 안테나 케이블을 분리합니다. 2 디스플레이 케이블 및 터치스크린 보드 케이블을 시스템 보드에 고정하는 접 착 테이프를 떼어냅니다. 3 래치를 열고 시스템 보드에서 디스플레이 케이블을 분리합니다.
4 래치를 열고 터치스크린 보드 케이블을 시스템 보드에서 분리합니다. 5 컴퓨터를 뒤집어 놓고 디스플레이를 완전히 열어 놓습니다. 그런 다음 평평한 표면에 컴퓨터를 뒤집어 놓습니다. 주의: 컴퓨터를 부드럽고 깨끗한 곳에 두어 디스플레이에 흠집이 생기는 것을 방지합니다. 6 40 디스플레이 조립품을 손목 받침대 조립품에 고정시키는 6개의 나사(M2.5x5) 를 분리합니다.
7 디스플레이 조립품을 가볍게 들어 올려 손목 받침대 조립품에서 분리합니다.
디스플레이 조립품 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 주의: 컴퓨터를 부드럽고 깨끗한 곳에 두어 디스플레이에 흠집이 생기는 것 을 방지합니다. 1 손목 받침대 조립품에 디스플레이 조립품을 놓습니다. 2 디스플레이 조립품의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니 다. 3 디스플레이 조립품을 손목 받침대 조립품에 고정시키는 6개의 나사(M2.5x5) 를 끼웁니다. 4 디스플레이를 닫고 컴퓨터를 뒤집습니다. 5 디스플레이 케이블 및 터치스크린 보드 케이블을 해당 슬롯에 밀어 넣고 래치 를 닫아 케이블을 고정시킵니다.
I/O 보드 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 절차 1 I/O 보드 케이블을 I/O 보드에 고정시키는 테이프를 떼어냅니다. 2 래치를 열고 I/O 보드 케이블을 I/O 보드에서 분리합니다.
3 I/O 보드에서 코인 셀 전지 케이블을 분리합니다. 4 I/O 보드를 키보드 브래킷에 고정하는 2개의 나사(M2x2)를 분리합니다.
5 I/O 보드를 들어 울려 손목 받침대 조립품에서 분리합니다.
I/O 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 I/O 보드를 손목 받침대 조립품 및 키보드 브래킷에 놓습니다. 2 I/O 보드의 나사 구멍을 손목 받침대 조립품의 나사 구멍과 키보드 브래킷의 나사 구멍에 맞춥니다. 3 I/O 보드를 키보드 브래킷에 고정하는 2개의 나사(M2x2)를 장착합니다. 4 I/O 보드에 코인 셀 배터리 케이블을 연결합니다. 5 I/O 보드 케이블을 I/O 보드의 커넥터에 밀어 넣고 래치를 닫아서 케이블을 고 정합니다.
솔리드 상태 드라이브 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 솔리드 상태 드라이브는 충격에 약합니다. 솔리드 상태 드라이브를 다 룰 때는 주의합니다. 주의: 데이터 손실 위험이 있으므로 컴퓨터가 켜져 있거나 절전 모드인 상태 에서 고정 상태 드라이브를 분리하지 마십시오. 필수 구성 요소 베이스 덮개를 분리합니다.
절차 1 시스템 보드에서 SSD를 찾습니다. 2 SSD를 키보드 브래킷에 고정하는 나사(M2x3)를 분리합니다. 3 SSD를 시스템 보드의 SSD 슬롯에서 밀어 분리합니다.
솔리드 상태 드라이브 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 솔리드 상태 드라이브는 충격에 약합니다. 솔리드 상태 드라이브를 다 룰 때는 주의합니다. 절차 1 SSD의 노치를 SSD 슬롯의 탭에 맞춥니다. 그런 다음 SSD를 SSD 슬롯으로 일 정 각도로 밉니다. 2 SSD의 나사 구멍을 키보드 브래킷의 나사 구멍에 맞춥니다. 3 SSD를 키보드 브래킷에 고정하는 나사(M2x3)를 장착합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
시스템 보드 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스 템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니 다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 노트: 시스템 보드에서 케이블을 분리하기 전에 커넥터의 위치를 기록하여 시스템 보드를 교체한 후에 정확하게 다시 연결할 수 있도록 합니다.
5 래치를 열고 I/O 보드 케이블을 시스템 보드에서 분리합니다. 6 Type-C 포트 브래킷을 시스템 보드 및 손목 받침대 조립품에 고정시키는 2개 의 나사(M2x3)를 분리합니다. 7 Type-C 포트 브래킷을 시스템 보드에서 들어 올려 분리합니다. 8 시스템 보드에서 스피커 케이블을 분리합니다. 9 래치를 열고 시스템 보드에서 키보드 케이블을 분리합니다. 10 래치를 열고 시스템 보드에서 키보드 백라이트 케이블을 분리합니다. 11 래치를 열고 시스템 보드에서 터치패드 케이블을 분리합니다.
12 래치를 열고 시스템 보드에서 상태 표시등 보드 케이블을 분리합니다. 13 시스템 보드를 키보드 브래킷에 고정하는 2개의 나사(M2x2)를 분리합니다.
14 시스템 보드를 들어 올려 손목 받침대 조립품에서 분리합니다.
시스템 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스 템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니 다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 절차 1 시스템 보드를 키보드 브래킷에 놓은 다음 시스템 보드의 나사 구멍을 키보드 브래킷의 나사 구멍에 맞춥니다.
7 시스템 보드에서 다음 커넥터를 덮고 있는 접착 테이프를 교체합니다. – I/O 보드 케이블 커넥터 – 터치 스크린 보드 케이블 커넥터 – 디스플레이 패널 케이블 커넥터 작업후 필수 조건 1 방열판을 장착합니다. 2 솔리드 상태 드라이브를 장착합니다. 3 배터리를 장착합니다. 4 베이스 덮개를 장착합니다.
상태 표시등 보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 절차 노트: 상태 표시등 보드에는 전원 및 배터리 상태 표시등/하드 드라이브 상 태 표시등을 위한 LED 표시등이 포함되어 있습니다. 1 래치를 열고 시스템 보드에서 상태 표시등 보드 케이블을 분리합니다. 2 분리 탭을 누르고 손목 받침대 조립품의 슬롯에서 상태 표시등 보드를 들어 올립니다.
3 스피커 케이블 아래에서 상태 표시등 보드 케이블을 밀고 상태 표시등 보드를 들어 올려 손목 받침대 조립품에서 분리합니다.
상태 표시등 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 상태 표시등 보드를 손목 받침대 조립품의 슬롯에 놓고 제자리에 끼웁니다. 2 스피커 케이블 아래에서 상태 표시등 케이블을 밉니다. 3 상태 표시등 보드 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 1 배터리를 장착합니다. 2 베이스 덮개를 장착합니다.
터치패드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 절차 1 래치를 열고 시스템 보드에서 터치패드 케이블을 분리합니다. 2 래치를 열고 시스템 보드에서 상태 보드 표시등 케이블을 분리합니다.
3 터치패드를 키보드 브래킷에 고정하는 접착 테이프 2개를 떼어냅니다. 4 터치패드를 손목 받침대 조립품에 고정하는 4개의 나사(M2x2)를 분리합니다.
5 터치패드를 밀고 들어 올려 손목 받침대 조립품의 슬롯에서 분리합니다.
터치패드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 손목 받침대 조립품의 슬롯으로 상태 표시등 보드 케이블 아래의 터치패드를 밀어 넣습니다. 2 터치패드를 손목 받침대 조립품에 고정하는 4개의 나사(M2x2)를 장착합니다. 3 터치패드를 키보드 브래킷에 고정하는 2개의 접착 테이프를 부착합니다. 4 터치패드 케이블 커넥터 래치를 열고 시스템 보드에 터치패드 케이블을 연결 합니다. 작업후 필수 조건 1 배터리를 장착합니다. 2 베이스 덮개를 장착합니다.
키보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 3 코인 셀 배터리를 분리합니다. 4 무선 카드를 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 I/O 보드를 분리합니다. 7 솔리드 상태 드라이브를 분리합니다. 8 방열판을 분리합니다. 9 팬을 분리합니다. 10 시스템 보드를 분리합니다. 절차 1 터치패드를 키보드 브래킷에 고정하는 접착 테이프 2개를 떼어냅니다.
3 키보드 브래킷을 키보드에서 들어 올려 분리합니다. 4 키보드를 손목 받침대 조립품에 고정하는 6개의 나사(M1.2x1.5)를 분리합니 다.
5 키보드를 들어 올려 손목 받침대 조립품에서 분리합니다.
키보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 키보드 케이블을 키보드 뒤쪽에 놓습니다. 2 키보드 케이블을 접는 선에 따라 맞추고 키보드 케이블을 접습니다. 3 손목 받침대 조립품에 키보드를 놓고 키보드의 나사 구멍을 손목 받침대 조립 품의 나사 구멍과 맞춥니다. 4 키보드를 손목 받침대 조립품에 고정하는 6개의 나사(M1.2x1.5)를 장착합니 다. 5 키보드 브래킷을 손목 받침대 조립품에 놓고 키보드 브래킷의 나사 구멍과 키 보드 및 손목 받침대 조립품의 나사 구멍을 맞춥니다.
6 키보드 브래킷과 키보드를 손목 받침대 조립품에 고정하는 27개의 나사 (M1.4x2)를 장착합니다. 7 터치패드를 키보드 브래킷에 고정하는 2개의 접착 테이프를 교체합니다. 작업후 필수 조건 1 시스템 보드를 장착합니다. 2 팬을 장착합니다. 3 방열판을 장착합니다. 4 솔리드 상태 드라이브를 장착합니다. 5 I/O 보드를 장착합니다. 6 디스플레이 어셈블리를 장착합니다. 7 무선 카드를 장착합니다. 8 코인 셀 배터리를 장착합니다. 9 배터리를 장착합니다. 10 베이스 덮개를 장착합니다.
손목 받침대 조립품 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 3 코인 셀 배터리를 분리합니다. 4 무선 카드를 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 I/O 보드를 분리합니다. 7 솔리드 상태 드라이브를 분리합니다. 8 방열판을 분리합니다. 9 팬을 분리합니다. 10 시스템 보드를 분리합니다. 11 전원 표시등 보드를 분리합니다. 12 터치패드를 분리합니다. 13 키보드를 분리합니다.
절차 모든 사전 요구 사항을 수행하면 손목 받침대 조립품이 남습니다.
손목 받침대 조립품 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽 어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내 부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추 가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지 (www.dell.com/regulatory_compliance)를 참조하십시오. 절차 손목 받침대를 평평한 곳에 뒤집어 놓습니다. 작업후 필수 조건 1 키보드를 장착합니다. 2 터치패드를 장착합니다. 3 전원 표시등 보드를 장착합니다.
4 시스템 보드를 장착합니다. 5 팬을 장착합니다. 6 방열판을 장착합니다. 7 솔리드 상태 드라이브를 장착합니다. 8 I/O 보드를 장착합니다. 9 디스플레이 어셈블리를 장착합니다. 10 무선 카드를 장착합니다. 11 코인 셀 배터리를 장착합니다. 12 배터리를 장착합니다. 13 베이스 덮개를 장착합니다.
드라이버 다운로드 오디오 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 Product Support(제품 지원)를 클릭해 컴퓨터의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드) → Find it myself(직접 찾기)를 클릭합니다. 5 페이지를 아래로 스크롤하여 Audio(오디오)를 확장합니다. 6 Download(다운로드)를 클릭하고 컴퓨터의 오디오 드라이버를 다운로드합니 다. 7 다운로드가 완료된 후 오디오 드라이버 파일을 저장한 폴더로 이동합니다. 8 오디오 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침에 따라 드라이버 를 설치합니다. 그래픽 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다.
8 그래픽 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침에 따라 드라이버 를 설치합니다. USB 3.0 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 Product Support(제품 지원)를 클릭해 컴퓨터의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드) → Find it myself(직접 찾기)를 클릭합니다. 5 페이지를 아래로 스크롤하여 Chipset(칩셋)을 확장합니다. 6 Download(다운로드)를 클릭하여 컴퓨터에 USB 3.0 드라이버를 다운로드합 니다. 7 다운로드가 완료된 후 USB 3.0 드라이버 파일을 저장한 폴더로 이동합니다. 8 USB 3.0 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침에 따라 드라이 버를 설치합니다.
미디어 카드 리더기 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 제품 지원을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합 니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드) → Find it myself(직접 찾기)를 클릭합니다. 5 페이지를 아래로 스크롤하여 Chipset(칩셋)을 확장합니다. 6 Download(다운로드)를 클릭하여 컴퓨터의 미디어 카드 리더기 드라이버를 다운로드합니다. 7 다운로드가 완료된 후 카드 리더기 드라이버 파일을 저장한 폴더로 이동합니 다. 8 카드 리더기 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침을 따릅니다. 칩셋 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다.
네트워크 드라이버 다운로드 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 Product support(제품 지원)을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드) → Find it myself(직접 찾기)를 클릭합니다. 5 페이지를 아래로 스크롤하여 Network(네트워크)를 확장합니다. 6 Download(다운로드)를 클릭하고 컴퓨터의 네트워크 드라이버를 다운로드합 니다. 7 다운로드가 완료된 후 파일을 저장하고, 네트워크 드라이버 파일을 저장한 폴 더로 이동합니다. 8 네트워크 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침을 따릅니다.
시스템 설정 노트: 컴퓨터 및 설치된 장치에 따라 이 섹션에 나열된 항목이 표시될 수도 있고 표시되지 않을 수도 있습니다. 부팅 순서 부팅 순서를 사용하여 시스템 설치가 정의하는 부팅 장치 순서를 생략하고 직접 특정 장치(예: 광학 드라이브 또는 하드 드라이브)로 부팅할 수 있습니다. 전원 켜 기 자체 테스트(POST) 중에 Dell 로고가 나타나면 다음 작업을 수행할 수 있습니 다. • F2 키를 눌러 시스템 설정에 액세스 • F12 키를 눌러 1회 부팅 메뉴 실행 부팅할 수 있는 장치가 진단 옵션과 함께 원타임 부팅 메뉴에 표시됩니다. 부팅 메 뉴 옵션은 다음과 같습니다: • 이동식 드라이브(사용 가능한 경우) • STXXXX 드라이브 노트: XXX는 SATA 드라이브 번호를 표시합니다. • 광학 드라이브(사용 가능한 경우) • 진단 노트: 진단을 선택하면, ePSA 진단 화면이 표시됩니다. 시스템 설정에 액세스 하기 위한 옵션도 부팅 시퀀스 화면에 표시됩니다.
키 탐색 아래쪽 화살표 다음 필드로 이동합니다. Enter 선택한 필드에서 값을 선택하거나(해당하는 경우) 필드의 링크로 이동합니다. 스페이스바 드롭다운 목록을 확장 또는 축소합니다(해당하는 경우). 탭 다음 작업 영역으로 이동합니다. 노트: 표준 그래픽 브라우저에만 해당됩니다. 기본 화면이 보일 때까지 이전 페이지로 이동합니다. 기본 화면에서 키를 누르면 저장하지 않은 변경 사항을 저장하고 시스템을 다시 시작하라는 메시지가 표시됩니다. Esc BIOS 개요 주의: 컴퓨터 전문가가 아닌 경우 BIOS 설정 프로그램의 설정을 변경하지 마 십시오. 설정을 변경할 경우, 컴퓨터가 제대로 작동하지 않을 수 있습니다. 노트: BIOS 설정 프로그램을 변경하기 전에 나중에 참조할 수 있도록 BIOS 설정 프로그램 화면 정보를 기록해 두는 것이 좋습니다. BIOS 설정 프로그램을 사용하여 다음과 같은 작업을 수행합니다.
2 POST 중에 DELL 로고가 표시되면 F2 프롬프트가 표시되는 즉시 F2 키를 누릅 니다. 노트: F2 프롬프트는 키보드가 초기화되었다는 것을 나타냅니다. 이 프 롬프트는 잠깐만 나타나므로, 표시되는지 잘 살폈다가 F2키를 누릅니 다. F2 프롬프트가 나타나기 전에 F2 키를 누르면 이 키 입력이 손실됩 니다. 시간이 초과되어 운영 체제 로고가 나타나면 바탕화면이 표시될 때까지 기다린 다음 컴퓨터를 끄고 다시 시도합니다. 시스템 설치 옵션 노트: 컴퓨터와 설치된 장치에 따라 이 섹션에 나열된 항목이 표시될 수도 있 고, 표시되지 않을 수도 있습니다. 표 3. 시스템 설치 옵션- 시스템 정보 메뉴 일반 사항 시스템 정보 BIOS Version BIOS 버전 번호를 표시합니다. Service Tag 컴퓨터의 서비스 태그를 표시합니다. Asset Tag 컴퓨터의 자산 태그를 표시합니다. 오너십 태그 컴퓨터의 소유자 자산 태그를 표시합니다.
일반 사항 프로세서 정보 프로세서 유형 프로세서 유형을 표시합니다. Core Count 프로세서의 코어 수를 표시합니다. Processor ID 프로세서 확인 코드를 표시합니다. Current Clock Speed 프로세서의 현재 클럭 속도를 표시합니다. Minimum Clock Speed 프로세서의 최소 클럭 속도를 표시합니다. Maximum Clock Speed 프로세서의 최대 클럭 속도를 표시합니다. Processor L2 Cache 프로세서 L2 캐시 크기를 표시합니다. Processor L3 Cache 프로세서 L3 캐시 크기를 표시합니다. HT Capable 프로세서가 하이퍼스레드(HT)가 가능한지 여부를 표시합니다. 64-Bit Technology 64비트 기술을 사용하는지 여부를 표시합니다. 장치 정보 SATA-0 컴퓨터의 SATA-0 장치 정보를 표시합니다. SATA-2 컴퓨터의 SATA-2 장치 정보를 표시합니다. M.
일반 사항 Boot Sequence 부팅 순서를 표시합니다. Boot List Option 사용 가능한 부팅 옵션을 표시합니다. Advanced Boot Options Enable Legacy Option ROMs 레거시 옵션 ROM을 활성화하거나 비활성화합니 다. 레거시 부팅 시도 활성화 레거시 부팅 시도를 활성화하거나 비활성화합니 다. UEFI 부팅 경로 보안 UEFI 부팅 경로를 부팅하기 위한 보안 레벨을 제어 합니다. Date/Time 현재 날짜를 MM/DD/YY 형식으로 표시하고 현재 시간을 HH:MM:SS AM/PM 형식으로 표시합니다. 표 4. 시스템 설치 옵션—시스템 구성 메뉴 시스템 구성 Integrated NIC 내장형 LAN 컨트롤러를 제어합니다. Enable UEFI Network Stack UEFI 네트워크 스택을 활성화하거나 비활성화합 니다. SATA Operation 내장형 SATA 하드 드라이브 컨트롤러의 작동 모드 를 구성합니다.
시스템 구성 오디오 내장형 오디오 컨트롤러를 활성화 또는 비활성화 합니다. Keyboard Illumination 키보드 조명 기능의 작동 모드를 구성합니다. Keyboard Backlight with AC AC 사용 키보드 백라이트를 활성화 또는 비활성화 합니다. 노트: 이 옵션은 키보드 조명에 영향을 미치 지 않습니다. Miscellaneous Devices 다양한 온보드 장치를 활성화 또는 비활성화할 수 있습니다. Enable Camera 카메라를 활성화 또는 비활성화합니다. Enable Secure Digital (SD) Card SD 카드 사용을 활성화 또는 비활성화합니다. 표 5. 시스템 설치 옵션—비디오 메뉴 비디오 LCD Brightness 배터리 및 AC 전원과 별개로 패널 밝기를 설정합 니다. 표 6. 시스템 설치 옵션—보안 메뉴 보안 어드민 패스워드 관리자 암호를 설정, 변경 또는 삭제합니다.
보안 Password Change 관리자 암호가 설정되어 있을 때 시스템 및 하드 디스크 암호에 대한 변경 내용을 활성화 또는 비활 성화합니다. Non-Admin Setup Changes 관리자 암호가 설정되어 있을 때 설정 옵션에 대한 변경 내용을 활성화 또는 비활성화합니다. UEFI Capsule Firmware Updates UEFI 캡슐 업데이트 패키지를 통한 BIOS 업데이트 를 활성화 또는 비활성화합니다. PTT Security 운영 체제 PTT(플랫폼 보안 기술) 표시를 활성화 또는 비활성화합니다. Computrace(R) Absolute Software에서 제공하는 선택적 Computrace(R) 서비스의 BIOS 모듈 인터페이스를 활성화 또는 비활성화합니다. CPU XD Support 프로세서의 실행 불능 모드를 활성화 또는 비활성 화합니다.
표 8. 시스템 설치 옵션—Intel 소프트웨어 가드 확장 메뉴 Intel 소프트웨어 가드 확장 Intel SGX Enable Intel 소프트웨어 가드 확장자를 활성화 또는 비활 성화합니다. Enclave Memory Size Intel 소프트웨어 가드 확장자 인클레이브 전용 메 모리 크기를 설정합니다. 표 9. 시스템 설치 옵션—성능 메뉴 성능 Multi Core Support 여러 코어를 활성화합니다. 기본값: 활성화 Intel SpeedStep Intel SpeedStep 기술을 활성화 또는 비활성화합니 다. 기본값: 활성화 노트: 활성화하는 경우, 프로세서 클럭 속도 와 코어 전력이 프로세서 부하에 따라 동적으 로 조정됩니다. C-States Control 추가 프로세서 절전 상태를 활성화 또는 비활성화 합니다. 기본값: 활성화 Intel TurboBoost 프로세서의 Intel TurboBoost 모드를 활성화 또는 비활성화합니다.
전원 관리 자동 날짜 켜짐이 매일, 평일 또는 선택한 요일에 설정된 경우에만 구성할 수 있습니다. 기본값: 비활성화 USB Wake Support USB 장치가 대기 모드의 컴퓨터를 재개하도록 설 정할 수 있습니다. Wake on LAN 꺼짐 상태 또는 최대 절전 모드에서 LAN 신호가 컴퓨터를 재개할 수 있습니다. 노트: 이 기능은 컴퓨터가 AC에 연결되어 있 을 때만 작동합니다. Advanced Battery Charge Configuration 시작 시간부터 지정한 작업 기간까지 고급 배터리 충전 구성 기능을 활성화할 수 있습니다. Primary Battery Charge Configuration 사전 선택한 사용자 지정 충전 시작 및 중지 정보 로 기본 배터리 충전을 설정합니다. 기본값: 적응형 표 11. 시스템 설치 옵션—POST 동작 메뉴 POST 동작 Adapter Warnings 어댑터 경고를 활성화 또는 비활성화합니다.
표 12. 시스템 설치 옵션—가상화 지원 메뉴 가상화 지원 Virtualization VMM(Virtual Machine Monitor)이 Intel 가상화 기술 이 제공하는 추가 하드웨어 기능을 활용할지 여부 를 지정합니다. VT for Direct I/O VMM(Virtual Machine Monitor)이 Direct I/O용 Intel 가상화 기술이 제공하는 추가 하드웨어 기능을 활 용할지 여부를 지정합니다. 표 13. 시스템 설치 옵션—무선 메뉴 무선 Wireless Switch 무선 장치를 무선 스위치로 제어할 수 있을지 여부 를 결정합니다. Wireless Device Enable 내부 무선 장치를 활성화 또는 비활성화합니다. 표 14. 시스템 설치 옵션—유지관리 메뉴 유지관리 Service Tag 컴퓨터의 서비스 태그를 표시합니다. Asset Tag 컴퓨터의 자산 태그를 생성합니다.
표 16. 시스템 설치 옵션—SupportAssist 시스템 해상도 SupportAssist System Resolution SupportAssist 시스템 해상도 콘솔 및 Dell OS 복구 도구에 대한 자동 부팅 흐름을 제어합니다. Auto OS Recovery Threshold SupportAssist OS Recovery 특정 시스템 오류에서의 SupportAssist OS 복구 도 구에 대한 자동 부팅 흐름까지 제어합니다. 시스템 및 설정 암호 컴퓨터 보안을 위해 시스템 및 설정 암호를 생성할 수 있습니다. 암호 유형 설명 시스템 암호 시스템 로그온하기 위해 입력해야 하는 암호. 설정 암호 컴퓨터의 BIOS 설정에 액세스하고 변경하기 위해 입력해야 하는 암호. 주의: 암호 기능은 컴퓨터 데이터에 기본적인 수준의 보안을 제공합니다. 주의: 컴퓨터가 잠겨 있지 않고 사용하지 않는 경우에는 컴퓨터에 저장된 데 이터에 누구라도 액세스할 수 있습니다.
2 시스템 암호 를 선택하고 새 암호 입력 필드에서 암호를 생성합니다. 다음 지침을 따라 시스템 암호를 할당합니다: – 암호 길이는 최대 32글자입니다. – 암호에는 0부터 9까지의 숫자가 포함될 수 있습니다. – 소문자만 유효하며 대문자는 사용할 수 없습니다. – 3 다음 특수 문자만 사용할 수 있습니다: 공백, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`). 새 암호 확인 필드에 입력했던 시스템 암호를 입력하고 OK(확인)를 클릭합니 다. 4 Esc와 변경 내용을 저장하라는 메시지를 누릅니다. 5 변경 사항을 저장하려면 Y를 누릅니다. 컴퓨터를 다시 부팅합니다. 현재 시스템 및/또는 설정 암호를 삭제하거나 변경 기존 시스템 및/또는 설정 암호를 삭제하거나 변경하려 시도하기 전에 Password Status(암호 상태)가 Unlocked(잠금 해제)되어 있는지(시스템 설정에서) 확인합니 다.
CMOS 설정 지우기 1 컴퓨터의 전원이 꺼져 있는지 확인합니다. 2 전원 어댑터를 컴퓨터에 연결하고 어댑터를 통해 컴퓨터에 공급되는 전원이 있는지 확인하십시오. 3 전원 버튼을 25초 동안 길게 누르면 RTC(Real Time Clock) 배터리가 리셋됩니 다. 4 전원 버튼을 놓습니다. 잊은 암호 삭제 잊은 암호를 삭제하려면 Dell 기술 지원 팀에 문의하십시오. www.dell.com/ contactdell을 참조하십시오.
문제 해결 BIOS 플래싱 사용 가능한 업데이트가 있거나 시스템 보드 교체 후 BIOS를 플래싱(업데이트)해 야 할 수 있습니다. BIOS를 업데이트하려면 다음 단계를 따릅니다. 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 Product support(제품 지원)을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴 퓨터 모델을 찾습니다. 4 Drivers & Downloads(드라이버 및 다운로드) → Find it myself(직접 찾기)를 클릭합니다. 5 컴퓨터에 설치된 운영 체제를 선택합니다. 6 페이지를 아래로 스크롤하여 BIOS를 확장할 수 있습니다. 7 Download(다운로드)을 클릭하여 컴퓨터 BIOS의 최신 버전을 다운로드합니 다. 8 다운로드가 완료된 후 BIOS 업데이트 파일을 저장한 폴더로 이동합니다.
• • 테스트가 성공적으로 완료되었음을 알리는 상태 메시지를 봅니다. 테스트 중 발생하는 문제를 알리는 오류 메시지를 봅니다. 주의: 시스템 진단 프로그램은 해당 컴퓨터를 테스트하는 데만 사용합니다. 이 프로그램을 다른 컴퓨터에 사용하면 유효하지 않은 결과 또는 오류 메시 지가 표시될 수 있습니다. 노트: 특정 장치를 위한 일부 테스트는 사용자 상호 작용을 요구합니다. 진단 테스트를 수행할 때는 항상 컴퓨터 터미널 앞을 지켜야 합니다. 자세한 내용은 Dell EPSA 진단 3.0을 참조하십시오. ePSA 진단 실행 1 컴퓨터를 켭니다. 2 컴퓨터가 부팅될 때 Dell 로고가 나타나면 F12 키를 누릅니다. 3 부팅 메뉴 화면에서 Diagnostics(진단) 옵션을 선택합니다. 4 왼쪽 하단의 화살표 키를 클릭합니다. 진단 전면 페이지가 표시됩니다. 5 오른쪽 하단의 화살표를 눌러 페이지 목록으로 이동합니다. 감지된 항목이 나열됩니다.
주황색 - 컴퓨터가 배터리로 실행 중이고 배터리 충전량이 5% 미만입니다. 꺼짐 • 전원 어댑터가 연결되어 있고 배터리가 완전히 충전되었습니다. • 컴퓨터가 배터리로 실행 중이고 배터리는 5% 이상입니다. • 컴퓨터가 대기 모드, 최대 절전 모드 또는 꺼져 있습니다. 예를 들어, 전원 및 배터리 상태 표시등이 황색으로 2번 깜박인 다음 일시 중지되 고, 이어서 흰색으로 3번 깜빡인 다음 일시 중지됩니다. 이 2, 3 패턴은 컴퓨터가 꺼 지면서 메모리 또는 RAM이 감지되지 않음을 나타낼 때까지 계속됩니다. 다음 표에서 표시등의 다양한 패턴과 의미를 설명합니다. 표 17.
잔류 전원 방출 잔류 전원은 컴퓨터 전원이 꺼지고 배터리가 분리된 후에도 컴퓨터에 남아 있는 잔여 정전기입니다. 다음과 같은 절차는 잔류 전원을 방출하는 방법에 대한 지침을 제공합니다. 1 컴퓨터를 끕니다. 2 베이스 덮개를 분리합니다. 3 약 15초간 전원 버튼을 눌러 잔류 전원을 방전시킵니다. 4 베이스 덮개를 장착합니다. 5 컴퓨터를 켭니다. Wi-Fi 전원 주기 Wi-Fi 연결 문제로 인해 컴퓨터에서 인터넷에 액세스할 수 없는 경우 Wi-Fi 전원 주 기 절차를 수행할 수 있습니다. 다음과 같은 절차는 Wi-Fi 전원 주기를 수행하는 방 법에 대한 지침을 제공합니다. 1 컴퓨터를 끕니다. 2 모뎀을 끕니다. 3 무선 라우터를 끕니다. 4 약 30초간 기다립니다. 5 라우터를 켭니다. 6 모뎀을 켭니다. 7 컴퓨터를 켭니다.
도움말 보기 및 Dell에 문의하기 자체 도움말 리소스 다음과 같은 자체 도움말 리소스를 이용해 Dell 제품 및 서비스에 관한 정보 및 도 움말을 얻을 수 있습니다. 표 18. 자체 도움말 리소스 Dell 제품 및 서비스 정보 www.dell.com Dell 도움말 및 지원 앱 도움말 액세스 Windows 검색에서 Help and Support을 입력한 다음 Enter를 누릅 니다. 운영 체제에 대한 온라인 도움말 www.dell.com/support/windows www.dell.com/support/linux 문제 해결 정보, 사용자 설명서, 설치 지 www.dell.com/support 침서, 제품 사양, 기술 지원 블로그, 드 라이버, 소프트웨어 업데이트 등. 다양한 컴퓨터 우려 사항에 대한 Dell 기 1 술 문서. 2 3 제품에 관한 다음 정보를 알아보십시 오. • • • • • 제품 사양 운영 체제 제품 설치 및 사용 데이터 백업 문제 해결 및 진단 www.dell.
• • 출하 시 및 시스템 복원 BIOS 정보 • • View Products(제품 보기) 아래의 드롭다운 메뉴를 통해 제품을 찾습 니다. 검색 창에 Service Tag number(서비 스 태그 번호) 또는 Product ID(제품 ID)를 입력합니다. Dell에 문의하기 판매, 기술 지원 또는 고객 서비스 문제에 관하여 Dell에 문의하려면 www.dell.com/ contactdell을 참조하십시오. 노트: 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지 역에 제공되지 않을 수 있습니다. 노트: 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서, 포장 명세서, 청 구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾을 수 있습니다.