Inspiron 7391 2n1 サービスマニュアル 規制モデル: P113G 規制タイプ: P113G001
メモ、注意、警告 メモ: 製品を使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明しています。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 © 2018 - 2019 Dell Inc.その関連会社。All rights reserved.Dell、EMC、およびその他の商標は、Dell Inc. またはその子会社の商標で す。その他の商標は、それぞれの所有者の商標である場合があります。 2019 - 07 Rev.
目次 1 コンピューター内部の作業.............................................................................................................. 5 安全にお使いいただくために........................................................................................................................................... 5 コンピュータ内部の作業を始める前に........................................................................................................................... 5 作業を開始する前に ..........................................................................
システム パスワードおよび管理者パスワード............................................................................................................ 62 システム セットアップパスワードの割り当て......................................................................................................62 既存のシステム/管理者パスワードの削除または変更........................................................................................ 62 CMOS 設定のクリア..............................................................................................................................
1 コンピューター内部の作業 安全にお使いいただくために 身体の安全を守り、コンピュータを損傷から保護するために、次の安全に関する注意に従ってください。特に記載のない限り、こ の文書に記載される各手順は、お使いのコンピューターに付属の「安全にお使いいただくための注意事項」をすでにお読みいただい ていることを前提とします。 メモ: コンピューター内部の作業を始める前に、お使いのコンピューターに付属しているガイドの安全にお使いいただくための 注意事項をお読みください。安全にお使いいただくためのベストプラクティスの詳細については、規制順守ホームページ (www.dell.
ESD(静電気放出)保護 電気パーツを取り扱う際、ESD は重要な懸案事項です。特に、拡張カード、プロセッサー、メモリ DIMM、およびシステムボードな どの静電気に敏感なパーツを取り扱う際に重要です。ほんのわずかな静電気でも、断続的に問題が発生したり、製品寿命が短くな ったりするなど、目に見えない損傷が回路に発生することがあります。省電力および高密度設計の向上に向けて業界が前進する 中、ESD からの保護はますます大きな懸念事項となってきています。 最近のデル製品で使用されている半導体の密度が高くなっているため、静電気による損傷の可能性は、以前のデル製品よりも高く なっています。このため、以前承認されていたパーツ取り扱い方法の一部は使用できなくなりました。 ESD による障害には、「致命的」および「断続的」の 2 つの障害のタイプがあります。 • • 致命的 – 致命的な障害は、ESD 関連障害の約 20 %を占めます。障害によりデバイスの機能が完全に直ちに停止します。致命的 な障害の一例としては、静電気ショックを受けたメモリ DIMM が直ちに「No POST/No Video(POST なし/ビデオ
• • • 作業現場環境 – ESD フィールド・サービス・キットを配備する前に、お客様の場所の状況を評価します。たとえば、サーバ環境用 にキットを配備するのと、デスクトップや携帯デバイス用にキットを配備することは異なります。サーバは通常、データセン ター内のラックに設置され、デスクトップや携帯デバイスはオフィスのデスク上か、仕切りで区切られた作業場所に配置されま す。物品が散乱しておらず ESD キットを広げるために十分な平らな広いエリアを探してください。このとき、修理対象のシス テムのためのスペースも考慮してください。また、作業場所に ESD の原因と成り得る絶縁体がないことも確認します。ハード ウェアコンポーネントを実際に取り扱う前に、作業場所では常に発泡スチロールおよびその他のプラスチックなどのインシュ レータは敏感なパーツから最低 30 cm(12 インチ)離して置きます。 静電気を防止する梱包 – すべての ESD に敏感なデバイスは、静電気の発生しない梱包材で発送および受領する必要がありま す。メタルアウト/静電気防止袋の使用をお勧めします。なお、損傷した部品は、新しい部品が納品されたとき
2 コンポーネントの取り外しと取り付け 推奨ツール この文書で説明する操作には、以下のツールが必要です。 • • • プラスドライバ#1 マイナスドライバ プラスチックスクライブ ネジのリスト メモ: コンポーネントからネジを取り外す際は、ネジの種類、ネジの数量をメモし、その後ネジの保管箱に入れておくことをお 勧めします。これは、コンポーネントを交換する際に正しいネジの数量と正しいネジの種類を保管しておくようにするためで す。 メモ: 一部のコンピューターには、磁性面があります。コンポーネントを交換する際、ネジが磁性面に取り付けられたままにな っていないことを確認してください。 メモ: ネジの色は、発注時の構成によって異なります。 表 1. ネジのリスト コンポーネント 固定先 ネジの種類 数 ベースカバー パームレストアセンブリ M2x4 6 バッテリ パームレストアセンブリ M1.6x4 1 バッテリ パームレストアセンブリ M2x2 大頭 4 ファン パームレストアセンブリ M2x2 2 ディスプレイヒンジ パームレストアセンブリ M2x3.
コンポーネント 固定先 ネジの種類 数 タッチパッドのブラケッ ト パームレストアセンブリ M1.6x2 3 タッチパッド パームレストアセンブリ M1.6x2 2 ワイヤレスカードブラケ ット システム基板 M2x3 1 ネジの画像 分解および再アセンブリ ベースカバー ベースカバーの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. ベースカバーをパームレスト アセンブリに固定している 2 本の拘束ネジを緩めます。 2. ベースカバーをパームレスト アセンブリに固定している 6 本のネジ(M2x4)を外します。 3.
メモ: バッテリ ケーブルは、続けてコンピューターから他のコンポーネントも取り外す場合にのみ取り外してください。 5. バッテリーケーブルをシステム基板から外します。 ベースカバーの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
手順 1. 必要に応じて、バッテリーケーブルをシステム基板に接続します。 2. ベースカバーのタブをパームレスト アセンブリのスロットの位置に合わせて、ベースカバーをパームレスト アセンブリにはめ込 みます。 3. ベースカバーをパームレスト アセンブリに固定する 2 本の拘束ネジを締めます。 4.
バッテリー バッテリーの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
前提条件 ベースカバーを取り外します。 手順 1. システム基板からバッテリ ケーブルを外します(すでに外されていない場合のみ)。 2. バッテリをパームレスト アセンブリーに固定しているネジ(M1.6x4)を外します。 3. バッテリをパームレスト アセンブリーに固定している 4 本のネジ(M2x2)を外します。 4. バッテリーを持ち上げて、パームレストアセンブリから取り外します。 5.
バッテリーの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. 位置合わせポストを使用して、バッテリをパームレスト アセンブリにセットします。 2. バッテリをパームレスト アセンブリーに固定する 4 本のネジ(M2x2)を取り付けます。 3. バッテリをパームレスト アセンブリーに固定するネジ(M1.6x4)を取り付けます。 4.
作業を終えた後に ベースカバーを取り付けます。 ワイヤレスカード ワイヤレスカードの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 ベースカバーを取り外します。 手順 1.
2. ワイヤレス カード ブラケットをワイヤレス カードとパームレスト アセンブリに固定しているネジ(M2x3)を外します。 3. ワイヤレスカードブラケットをワイヤレスカードから取り外します。 4. アンテナケーブルをワイヤレスカードから外します。 5. ワイヤレスカードをスライドさせて、ワイヤレスカードスロットから取り外します。 ワイヤレスカードの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
手順 注意: ワイヤレスカードへの損傷を避けるため、カードの下にケーブルを置かないでください。 1. ワイヤレス カード スロットのフラップを持ち上げます。 2. アンテナケーブルをワイヤレスカードに接続します。 次の表に、お使いのコンピューターがサポートするワイヤレス カード用アンテナケーブルの色分けを示します。 表 2. アンテナケーブルの色分け ワイヤレスカードのコネクタ アンテナケーブルの色 メイン(白色の三角形) 白色 補助(黒色の三角形) 黒色 3. ワイヤレスカードの切込みをワイヤレスカードスロットのタブに合わせて、ワイヤレスカードを傾けてワイヤレスカードスロッ トに差し込みます。 4. ワイヤレス カード ブラケットのネジ穴を、ワイヤレス カードとパームレスト アセンブリのネジ穴に合わせます。 5.
作業を終えた後に ベースカバーを取り付けます。 電源アダプタポート 電源アダプタポートの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 ベースカバーを取り外します。 手順 1. 左のディスプレイ ヒンジをシステム基板に固定している 3 本のネジ(M2x3.5)を外します。 2. 左のディスプレイ ヒンジを持ち上げ、システム基板から取り外します。 3. 電源アダプタポートケーブルをシステム基板から外します。 4. 電源アダプタ ポートをパームレスト アセンブリに固定しているネジ(M2x3)を外します。 5.
電源アダプタポートの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. 電源アダプタポートをパームレストアセンブリのスロットにセットします。 2. 電源アダプタ ポートをパームレスト アセンブリに固定するネジ(M2x3)を取り付けます。 3. 電源アダプタポートケーブルをシステム基板に接続します。 4. 左のディスプレイ ヒンジを閉じます。 5. 左のディスプレイ ヒンジをシステム基板に固定する 3 本のネジ(M2x3.
作業を終えた後に ベースカバーを取り付けます。 I/O ボード I/O ボードの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 ベースカバーを取り外します。 手順 1. 右のディスプレイ ヒンジを I/O ボードに固定している 2 本のネジ(M2x3.5)を外します。 2. 右のディスプレイ ヒンジを持ち上げて、I/O ボードから取り外します。 3. I/O ボードケーブルを I/O ボードに固定しているテープを剥がします。 4. ラッチを開き、I/O ボードケーブルを I/O ボードから外します。 5.
I/O ボードの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. I/O ボードをパームレスト アセンブリのスロットに差し込みます。 2. I/O ボードケーブルを I/O ボードのコネクタに差し込み、ラッチを閉じてケーブルを固定します。 3. I/O ボードケーブルを I/O ボードに固定するテープを貼り付けます。 4. 右のディスプレイヒンジを閉じます。 5. 右のディスプレイ ヒンジを I/O ボードに固定する 2 本のネジ(M2x3.
作業を終えた後に ベースカバーを取り付けます。 ファン ファンの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 ベースカバーを取り外します。 手順 1. ファンケーブルをシステム基板から外します。 2. ファン ケーブルをファンに固定するテープをはがします。 3. ファンをパームレスト アセンブリに固定している 2 本のネジ(M2x2)を取り外します。 4.
ファンの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. 位置合わせポストを使用して、ファンをパームレスト アセンブリにセットします。 2. ファンをパームレスト アセンブリに固定する 2 本のネジ(M2x3)を取り付けます。 3. ファン ケーブルをファンに固定するテープを貼り付けます。 4.
作業を終えた後に ベースカバーを取り付けます。 ソリッドステートデバイス ソリッドステートドライブの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 注意: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 注意: データの損失を防ぐため、コンピュータの電源が入っている状態、またはスリープ状態のときに SSD を取り外さないで ください。 前提条件 ベースカバーを取り外します。 M.2 2230 ソリッドステート ドライブの取り外し手順 1.
M.2 2280 ソリッドステート ドライブの取り外し手順 1.
2. ソリッドステート ドライブ/インテル Optane ストレージ モジュール をパームレスト アセンブリに固定しているネジ(M2x2)を 外します。 3. ソリッドステート ドライブ/インテル Optane ストレージ モジュールをソリッドステート ドライブのスロットから引き出して取 り外します。 ソリッドステートドライブの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 注意: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 M.2 2230 ソリッドステート ドライブの取り付け手順 1.
M.2 2280 ソリッドステート ドライブの取り付け手順 1. ソリッドステート ドライブ/インテル Optane ストレージ モジュールの切り込みを、ソリッドステート ドライブ スロットのタブ に合わせます。 2. ソリッドステート ドライブ/インテル Optane ストレージ モジュール をパームレスト アセンブリに固定するネジ(M2x2)を取り 付けます。 作業を終えた後に ベースカバーを取り付けます。 コイン型電池 コイン型電池の取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
前提条件 1. ベースカバーを取り外します。 2. バッテリーを取り外します。 手順 1. コイン型電池ケーブルをパームレスト アセンブリーに固定しているテープを剥がします。 2. コイン型電池ケーブルをパームレスト アセンブリの配線ガイドから外します。 3. コイン型電池ケーブルをシステム基板から外します。 4. コイン型電池をパームレストアセンブリから取り出します。 コイン型電池の取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. コイン型電池をパームレストアセンブリに取り付けます。 2. コイン型電池ケーブルをシステム基板に接続します。 3.
作業を終えた後に 1. バッテリーを取り付けます。 2. ベースカバーを取り付けます。 タッチパッド タッチパッドの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 1. ベースカバーを取り外します。 2. バッテリーを取り外します。 手順 1. スピーカー ケーブルをタッチパッド ブラケットに固定しているテープをはがします。 2. タッチパッド ブラケットをパームレスト アセンブリに固定している 3 本のネジ(M1.6x2)を外します。 3. タッチパッド ブラケットを持ち上げて、パームレスト アセンブリーから取り外します。 4.
タッチパッドの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. タッチパッドをパームレスト アセンブリのスロットにスライドします。 2. タッチパッドをパームレスト アセンブリーに固定する 2 本のネジ(M1.6x2)を取り付けます。 3. タッチパッドをパームレスト アセンブリに固定するテープを貼り付けます。 4. タッチパッド ケーブルをパームレスト アセンブリに接着してタッチパッドのコネクタに差し込み、ラッチを閉じてケーブルを 固定します。 5. タッチパッド ブラケットのネジ穴をパームレスト アセンブリーのネジ穴の位置に合わせます。 6.
作業を終えた後に 1. バッテリーを取り付けます。 2. ベースカバーを取り付けます。 スピーカー スピーカーの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 1. ベースカバーを取り外します。 2. バッテリーを取り外します。 手順 1. スピーカー ケーブルをコネクタに固定しているテープをはがします。 2. スピーカーケーブルをシステム基板から外します。 3. テープをはがしてパームレスト アセンブリの配線ガイドからスピーカー ケーブルを外します。 4. スピーカーケーブルをパームレストアセンブリの配線ガイドから外します。 5.
スピーカーの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. パームレスト アセンブリの位置合わせポストを使用して、両方のスピーカーをパームレスト アセンブリにセットします。 2. スピーカー ケーブルをパームレスト アセンブリの配線ガイドに通して配線し、。 3. スピーカー ケーブルをタッチパッド ブラケットに固定するテープを貼り付けます。 4. システム基板にスピーカーケーブルを接続します。 5.
作業を終えた後に 1. バッテリーを取り付けます。 2. ベースカバーを取り付けます。 ヒートシンク ヒートシンクの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 メモ: 通常の動作中、ヒートシンクが高温になる場合があります。温度が十分に下がりヒートシンクが冷えるのを待って、触っ てください。 注意: プロセッサの冷却効果を最大にするために、ヒートシンクの放熱部分には触れないでください。皮脂が付着すると、サー マルグリースの放熱能力が低下する場合があります。 前提条件 1. ベースカバーを取り外します。 2. ファンを取り外します。 手順 1.
ヒートシンクの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 注意: ヒートシンクの位置が正しく合っていないと、システム基板とプロセッサを損傷する可能性があります。 メモ: システム基板またはヒートシンクのいずれかを取り付ける場合は、熱伝導性を確保するために、キット内のサーマルパッ ド/ペーストを使用してください。 手順 1. ヒートシンクのネジ穴をシステム基板のネジ穴に合わせます。 2.
作業を終えた後に 1. ファンを取り付けます。 2. ベースカバーを取り付けます。 ディスプレイアセンブリ ディスプレイアセンブリの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 1. ベースカバーを取り外します。 2. ファンを取り外します。 手順 1. タッチスクリーンボード ケーブルをシステム基板に固定しているテープを剥がします。 2. ラッチを開き、タッチスクリーンボード ケーブルをシステム基板から外します。 3. テープをはがしてタッチスクリーンボード ケーブルを外し、パームレスト アセンブリの配線ガイドからケーブルを外します。 4.
8. コンピュータを表向きに置き、ディスプレイを可能な限り開きます。 注意: ディスプレイを傷付けないように、コンピュータを柔らかく、清潔な面に置きます。 9. コンピューターを裏返して、ディスプレイ ヒンジを I/O ボードとシステム基板に固定している 5 本のネジ(M2.5x3.5)を取り外 します。 10.
ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 注意: ディスプレイを傷付けないように、コンピュータを柔らかく、清潔な面に置きます。 1. ディスプレイアセンブリをパームレストアセンブリ上にセットします。ディスプレイ ヒンジのネジ穴を I/O ボードとシステム 基板のネジ穴に合わせます。 2. ディスプレイ ヒンジを I/O ボードとシステム基板に固定している 5 本のネジ(M2.5x3.5)を取り付けます。 3. ディスプレイを閉じます。 4. モニタ ケーブルをパームレスト アセンブリの配線ガイドに沿って配線します。 5. ディスプレイケーブルをシステム基板に固定するテープを貼り付けます。 6. モニタ ケーブルをシステム基板に接続し、ラッチを閉じてケーブルを固定します。 7. ディスプレイケーブルをシステム基板に固定するテープを貼り付けます。 8.
作業を終えた後に 1. ファンを取り付けます。 2. ベースカバーを取り付けます。 システム基板 システム基板の取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
6. ヒートシンクを取り外します。 手順 1. 左のディスプレイ ヒンジをシステム基板に固定している 3 本のネジ(M2x3.5)を外します。 2. 左のディスプレイ ヒンジを持ち上げ、システム基板から取り外します。 3. ディスプレイケーブルをシステム基板に固定しているテープを剥がします。 4. ラッチを開き、システム基板からディスプレイケーブルを外します。 5. ディスプレイケーブルをシステム基板に固定しているテープを剥がします。 6. 電源アダプタポートケーブルをシステム基板から外します。 7. スピーカー ケーブルをコネクタに固定しているテープをはがします。 8. スピーカーケーブルをシステム基板から外します。 9. ラッチを開いて、システム基板からキーボードケーブルを外します。 10. ラッチを開き、キーボードバックライト ケーブルをシステム基板から外します。 11. ラッチを開き、タッチパッド ケーブルをシステム基板から外します。 12. コイン型電池ケーブルをシステム基板から外します。 13. I/O ボードケーブルをシステム基板に固定しているテープを剥がします。 14.
18. システム基板をパームレスト アセンブリに固定している 4 本のネジ(M2x2)を取り外します。 19. システム基板を持ち上げて、パームレストアセンブリから取り外します。 システム基板の取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
メモ: システム基板には、コンピューターのサービスタグが保存されています。システム基板を取り付けた後、BIOS セットア ッププログラムでこのサービスタグを入力する必要があります。 メモ: システム基板を取り付けると、BIOS セットアッププログラムで行った BIOS への変更はすべて削除されます。システム 基板を取り付けた後に、再度適切な変更を行う必要があります。 手順 1. システム基板のネジ穴をパームレストアセンブリのネジ穴の位置に合わせます。 2. システム基板をパームレスト アセンブリに固定する 4 本のネジ(M2x2)を取り付けます。 3. 指紋認証リーダー ケーブルをシステム基板に差し込み、ラッチを閉じてケーブルを固定します。 4. タッチスクリーン ボード ケーブルをシステム基板に差し込み、ラッチを閉じてケーブルを固定します。 5. タッチスクリーン ボード ケーブルをシステム基板に固定するテープを貼り付けます。 6. I/O ボード ケーブルをシステム基板に差し込み、ラッチを閉じてケーブルを固定します。 7. I/O ボードケーブルをシステム基板に固定するテープを貼り付けます。 8.
18. 左のディスプレイ ヒンジを閉じます。 19. 左のディスプレイ ヒンジをシステム基板に固定する 3 本のネジ(M2x3.5)を取り付けます。 作業を終えた後に 1. ヒートシンクを取り付けます。 2. ファンを取り付けます。 3. ワイヤレスカードを取り付けます。 4. ソリッドステートドライブを取り付けます。 5.
6. ベースカバーを取り付けます。 BIOS セットアッププログラムへのサービスタグの入力 1. コンピュータの電源を入れます(または再起動します)。 2. Dell のロゴが表示されたら を押して BIOS セットアッププログラムを起動します。 3. Main(メイン)タブに移動して、Service Tag Input(サービスタグ入力)フィールドにサービスタグを入力します。 メモ: サービスタグは、コンピュータの背面に貼付されている英数字の ID です。 キーボード キーボードの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 前提条件 1.
4. キーボード ブラケットをキーボードに固定している 29 本のネジ(M1.2x1.8)を外します。 メモ: キーボード ブラケットのプラスチック製のシートを持ち上げて、ネジを取り出せるようにします。 5. キーボードブラケットを持ちあげてキーボードから取り外します。 6. キーボードをパームレスト アセンブリに固定している 4 本のネジ(M1.2x1.8)を外します。 7.
キーボードの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 1. キーボードのネジ穴をパームレストアセンブリのネジ穴の位置に合わせます。 2. キーボードをパームレスト アセンブリに固定する 4 本のネジ(M1.2x1.
3. キーボード ブラケットのネジ穴をキーボードのネジ穴に合わせます。 4. キーボード ブラケットをキーボードに固定する 29 本のネジ(M1.2x1.8)を取り付けます。 5. キーボード ブラケットのプラスチック製のシートを取り付けます。 6. アンテナ ケーブルをキーボード ブラケットに固定するテープを貼り付けます。 7.
作業を終えた後に 1. システム基板を取り付けます。 2. 指紋認証リーダー内蔵電源ボタンを取り付けます。 3. I/O ボードを取り付けます。 4. ディスプレイアセンブリを取り付けます。 5. ファンを取り付けます。 6. スピーカーを取り付けます。 7. ワイヤレスカードを取り付けます。 8. コイン型電池を取り付けます。 9. ソリッドステートドライブを取り付けます。 10. バッテリーを取り付けます。 11. ベースカバーを取り付けます。 指紋認証リーダー内蔵電源ボタン 指紋認証リーダー内蔵電源ボタンの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
5. ワイヤレスカードを取り外します。 6. スピーカーを取り外します。 7. ファンを取り外します。 8. ディスプレイアセンブリを取り外します。 9. I/O ボードを取り外します。 10. システム基板を取り外します。 手順 1. 「キーボードの取り外し」の手順 1 から 5 に従ってください。 2. ラッチを開いて、指紋認証リーダー ケーブルを指紋認証リーダー内蔵電源ボタンから外します。 3. 指紋認証リーダー内蔵電源ボタンを電源ボタン ケーブルとともに持ち上げて、キーボード ブラケットから取り外します。 4.
4. 「キーボードの取り付け」の手順 3 から 8 に従ってください。 作業を終えた後に 1. システム基板を取り付けます。 2. I/O ボードを取り付けます。 3. ディスプレイアセンブリを取り付けます。 4. ファンを取り付けます。 5. スピーカーを取り付けます。 6. ワイヤレスカードを取り付けます。 7. コイン型電池を取り付けます。 8. ソリッドステートドライブを取り付けます。 9. バッテリーを取り付けます。 10. ベースカバーを取り付けます。 パームレストとアンテナ アセンブリ パームレストとアンテナ アセンブリの取り外し メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.
7. ソリッドステートドライブを取り外します。 8. コイン型電池を取り外します。 9. タッチパッドを取り外します。 10. スピーカーを取り外します。 11. ディスプレイアセンブリを取り外します。 12. システム基板を取り外します。 13. キーボードを取り外します。 14. 指紋認証リーダー内蔵電源ボタンを取り外します。 手順 「作業を開始する前に」の手順を実行してから、パームレストを取り外します。 パームレストとアンテナ アセンブリの取り付け メモ: コンピュータ内部の作業を始める前に、お使いのコンピュータに付属している「安全にお使いいただくための注意事項」を 読んで、「コンピュータ内部の作業を始める前に」の手順を実行してください。コンピュータ内部の作業を終えた後は、「コンピ ュータ内部の作業を終えた後に」の指示に従ってください。安全にお使いいただくためのベストプラクティスの詳細について は、規制順守ホームページ(www.dell.com/regulatory_compliance)をご覧ください。 手順 パームレストを平らな面に置きます。 作業を終えた後に 1.
8. ソリッドステートドライブを取り付けます。 9. I/O ボードを取り付けます。 10. 電源アダプタポートを取り付けます。 11. ワイヤレスカードを取り付けます。 12. ファンを取り付けます。 13. バッテリーを取り付けます。 14.
3 デバイスドライバ Intel チップセットソフトウェアインストールユーテ ィリティ デバイスマネージャでチップセットドライバがインストールされているかどうかを確認します。 www.dell.com/support から Intel チップセットのアップデートをインストールします。 ビデオドライバ デバイスマネージャでビデオドライバがインストールされているかどうかを確認します。 www.dell.com/support からビデオドライバのアップデートをインストールします。 Intel シリアル IO ドライバ デバイスマネージャで Intel シリアル I/O ドライバがインストールされているかどうかを確認します。 www.dell.com/support からドライバのアップデートをインストールします。 Intel Trusted Execution Engine インタフェース デバイスマネージャで、Intel Trusted Execution Engine インタフェースドライバがインストールされているかどうかを確認します。 www.dell.
4 セットアップユーティリティ メモ: お使いのコンピュータおよび取り付けられているデバイスによっては、本項に一覧表示された項目の一部がない場合があ ります。 トピック: • • • • • • セットアップユーティリティ BIOS セットアッププログラムの起動 ナビゲーションキー 起動順序 セットアップユーティリティのオプション システム パスワードおよび管理者パスワード セットアップユーティリティ 注意: コンピューターに詳しい方以外は、BIOS セットアップ プログラムの設定を変更しないでください。特定の変更でコンピ ュータが誤作動を起こす可能性があります。 メモ: BIOS セットアップ プログラムを変更する前に、後で参照できるように、BIOS セットアップ プログラム画面の情報を控 えておくことをお勧めします。 BIOS セットアップ プログラムは次の目的で使用します。 • • • RAM の容量やハード ドライブのサイズなど、コンピューターに取り付けられているハードウェアに関する情報の取得。 システム設定情報の変更。 ユーザー パスワード、取り付けられたハード ドライブの種類、基本デバイス
起動順序 起動順序を利用すると、セットアップユーティリティで定義されたデバイス起動順序をバイパスし、特定のデバイス(例:オプテ ィカルドライブまたはハードドライブ)から直接起動することができます。電源投入時の自己テスト(POST)中に Dell のロゴが表 示されたら、以下が可能になります。 • • を押してセットアップユーティリティにアクセスする を押して 1 回限りの起動メニューを立ち上げる 1 回限りの起動メニューでは診断オプションを含むオプションから起動可能なデバイスを表示します。起動メニューのオプション は以下のとおりです。 • • リムーバブルドライブ(利用可能な場合) STXXXX ドライブ(利用可能な場合) メモ: XXX は、SATA ドライブの番号を意味します。 • • • オプティカルドライブ(利用可能な場合) SATA ハード ドライブ(利用可能な場合) 診断 メモ: Diagnostics(診断)を選択すると ePSA 診断 画面が表示されます。 起動順序画面ではシステムセットアップ画面にアクセスするオプションを表示することも可能です。 セットアッ
概要 Processor L2 Cache プロセッサの L2 キャッシュサイズを表示します。 Processor ID プロセッサの識別コードを表示します。 Processor L3 Cache プロセッサの L3 キャッシュサイズを表示します。 Current Clock Speed プロセッサの現在のクロック速度を表示します。 Minimum Clock Speed プロセッサの最低クロック速度を表示します。 マイクロコードのバージョン マイクロコード バージョンを表示します。 インテル ハイパースレッディング対応 プロセッサがハイパースレッディング(HT)に対応しているかどうかを表示しま す。 64-Bit Technology 64 ビットテクノロジーが使用されているかどうかを表示します。 メモリ情報 Memory Installed インストールされているコンピュータメモリの合計を表示します。 Memory Available 使用可能なコンピュータメモリの合計を表示します。 Memory Speed メモリ速度を表示します。 Memory Channe
表 5.
システム設定 タッチスクリーン オペレーティング システムのタッチスクリーンを有効または無効にします。 メモ: タッチスクリーンは、この設定に関係なく、BIOS セットアップで常に 動作します。 デフォルト:ON(オン) 表 6. セットアップユーティリティのオプション — ビデオメニュー ビデオ LCD Brightness Brightness on battery power コンピューターがバッテリ電源で動作しているときに、画面の輝度を設定します。 Brightness on AC power コンピューターが AC 電源で動作しているときに、画面の輝度を設定します。 EcoPower 必要に応じて画面の輝度を下げることにより、バッテリの寿命を延ばす EcoPower を有効または無効にします。 デフォルト:ON(オン) 表 7.
セキュリティ Intel SGX インテル Software Guard Extensions(SGX)によるコードの実行/機密情報の保存 のための安全な環境の提供を有効または無効にします。 デフォルト:Software Control SMM Security Mitigation 追加の UEFI SMM セキュリティ緩和の保護を有効または無効にします。 デフォルト:OFF(オフ) メモ: この機能により、一部のレガシー ツールやアプリケーションで互換性の 問題または機能の損失が発生する可能性があります。 Enable Strong Passwords 強力なパスワードを有効または無効にします。 デフォルト:OFF(オフ) Password Configuration 管理者パスワードとシステム パスワードの最小、および最大文字数を設定しま す。 Admin Password 管理者(admin)パスワード(「セットアップ」パスワードと呼ばれる場合もある) を設定、変更、または削除します。 System Password システム パスワードを設定、変更、または削除します。 Ena
パフォーマンス Intel SpeedStep インテル SpeedStep テクノロジーがプロセッサーの電圧とコア周波数を動的に調 整し、平均電力消費量と発熱量を削減する機能を有効または無効にします。 デフォルト:ON(オン) Intel TurboBoost Technology プロセッサーのインテル TurboBoost モードを有効または無効にします。有効な 場合、インテル TurboBoost ドライバは、CPU またはグラフィックス プロセッサ ーのパフォーマンスを向上させます。 デフォルト:ON(オン) Multi-Core Support オペレーティング システムで使用可能な CPU コアの数を変更します。デフォル ト値は、コアの最大数に設定されています。 デフォルト:All Cores。 Enable C-State Control 低電力状態を開始して終了する CPU の機能を有効または無効にします。 デフォルト:ON(オン) 表 11.
表 12. セットアップユーティリティのオプション — ワイヤレスメニュー ワイヤレス Wireless Switch ワイヤレス スイッチでどのワイヤレス デバイスを制御できるかを決定します。 Windows 8 システムの場合、これはオペレーティング システム ドライブに直接制 御されます。したがって、この設定はワイヤレス スイッチの動作には影響しませ ん。 メモ: WLAN と WiGig の両方が存在する場合、有効化/無効化の制御は連動し ています。したがって、個別に有効または無効にすることはできません。 WLAN デフォルト:ON(オン) Bluetooth デフォルト:ON(オン) Wireless Device Enable 内蔵 WLAN/Bluetooth デバイスを有効または無効にします。 WLAN デフォルト:ON(オン) Bluetooth デフォルト:ON(オン) 表 13.
仮想化 VT for Direct I/O コンピューターがダイレクト I/O の仮想化テクノロジー(VT-d)を実行できるよ うにします。VT-d は、メモリ マップ I/O の仮想化を実現するインテルの方法で す。 デフォルト:ON(オン) 表 15.
システム パスワードおよび管理者パスワード 表 18. システム パスワードおよび管理者パスワード パスワードの種類 説明 システムパスワード コンピューターにログオンする際に入力が必要なパスワードで す。 管理者パスワード コンピューターのセキュリティ機能を有効にするために入力す る必要があるパスワードです。 システム パスワードと管理者パスワードは、お使いのコンピューターを保護するため作成することができます。 注意: パスワード機能は、コンピュータ内のデータに対して基本的なセキュリティを提供します。 注意: コンピュータをロックせずに放置すると、コンピュータ上のデータにアクセスされる可能性があります。 メモ: システム パスワードと管理者パスワードの機能は無効になっています。 システム セットアップパスワードの割り当て セットアップユーティリティを起動するには、電源投入または再起動の直後に を押します。 1. System BIOS 画面または System Setup 画面の左ペインで、Passwords を選択します。 Passwords 画面が表示されます。 2.
1. ベースカバーを取り外します。 2. バッテリーケーブルをシステム基板から外します。 3. コイン型電池を取り外します。 4. 1 分間待ちます。 5. コイン型電池を取り付けます。 6. バッテリーケーブルをシステム基板に接続します。 7. ベースカバーを取り付けます。 BIOS(システム セットアップ)パスワードとシステム パス ワードのクリア システムまたは BIOS パスワードをクリアするには、Dell テクニカル サポート(www.dell.
5 トラブルシューティング ePSA(強化された起動前システムアセスメント)診 断 ePSA 診断(システム診断とも呼ばれる)ではハードウェアの完全なチェックを実行します。ePSA は BIOS に組み込まれており、 BIOS によって内部で起動します。組み込み型システム診断プログラムには、特定のデバイスまたはデバイス グループ用の一連の オプションが用意されており、以下の処理が可能です。 • • • • • • テストを自動的に、または対話モードで実行 テストの繰り返し テスト結果の表示または保存 詳細なテストで追加のテストオプションを実行し、障害の発生したデバイスに関する詳しい情報を得る テストが問題なく終了したかどうかを知らせるステータスメッセージを表示 テスト中に発生した問題を通知するエラーメッセージを表示 メモ: 特定のデバイスについては、ユーザーによる操作が必要なテストもあります。診断テストを実行する際は、コンピュー ター端末の前に必ずいるようにしてください。 ePSA 診断の実行 1. コンピュータの電源を入れます。 2.
表 19.
BIOS のフラッシュ 更新がある場合やシステム基板を取り付けるときに BIOS のフラッシュ(更新)を行う必要があります。 次の手順に従って、BIOS のフラッシュを行います。 1. コンピュータの電源を入れます。 2. www.dell.com/support にアクセスします。 3. Product Support(製品サポート)をクリックし、お使いのコンピュータのサービスタグを入力して、Submit(送信)をクリッ クします。 メモ: サービスタグがない場合は、自動検出機能を使用するか、お使いのコンピュータのモデルを手動で参照してください。 4. Drivers & downloads(ドライバとダウンロード) > Find it myself(自分で検索)をクリックします。 5. お使いのコンピュータにインストールされているオペレーティングシステムを選択します。 6. ページを下にスクロールして、 BIOS を展開します。 7. Download(ダウンロード)をクリックして、お使いのコンピュータの BIOS の最新バージョンをダウンロードします。 8.
1. コンピュータの電源を切ります。 2. モデムの電源を切ります。 3. ワイヤレス ルータの電源を切ります。 4. 30 秒待ちます。 5. ワイヤレス ルータの電源を入れます。 6. モデムの電源を入れます。 7. コンピュータの電源を入れます。 待機電力の放出 待機電力とは、コンピュータの電源をオフにしてバッテリを取り外した後もコンピュータに残っている余分な静電気のことを指し ます。次の手順は、待機電力の放出方法を説明したものです。 1. コンピュータの電源を切ります。 2. 電源アダプタをコンピュータから外します。 3. 電源ボタンを 15 秒間長押しして、待機電力を逃がします。 4. 電源アダプタをコンピュータに接続します。 5.