Inspiron 7586 서비스 설명서 규정 모델: P76F 규정 유형: P76F001
참고, 주의 및 경고 노트: "참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. © 2018 Dell Inc. 또는 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상표일 수 있습 니다.
목차 1 컴퓨터 내부 작업을 시작하기 전에................................................................................................................. 8 시작하기 전에 ...................................................................................................................................................................8 2 컴퓨터 내부 작업을 마친 후에....................................................................................................................... 9 3 안전 지침.....................................................
절차................................................................................................................................................................................... 24 작업후 필수 조건............................................................................................................................................................ 24 14 팬 분리.......................................................................................................................................................
25 무선 카드 장착...........................................................................................................................................42 절차................................................................................................................................................................................... 42 작업후 필수 조건............................................................................................................................................................
절차................................................................................................................................................................................... 55 37 터치패드 장착............................................................................................................................................56 절차............................................................................................................................................................................
절차....................................................................................................................................................................................74 49 디스플레이 케이블 교체.............................................................................................................................75 절차...................................................................................................................................................................................
1 컴퓨터 내부 작업을 시작하기 전에 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 시작하기 전에 1 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2 컴퓨터를 종료하십시오. Start(시작) > 3 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. Power(전원) > Shut down(종료)을 클릭합니다. 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에서 종료 지침을 참조하십시오. 4 키보드, 마우스, 모니터 등과 같은 연결된 모든 네트워크 기기와 주변 장치를 컴퓨터에서 분리합니다. 5 해당하는 경우, 모든 미디어 카드 및 광학 디스크를 컴퓨터에서 분리합니다.
2 컴퓨터 내부 작업을 마친 후에 주의: 컴퓨터 내부에 나사가 남아 있거나 느슨한 나사가 존재하는 경우 컴퓨터가 심각하게 손상될 수 있습니다. 1 나사를 모두 장착하고 컴퓨터 내부에 남아 있는 나사가 없는지 확인합니다. 2 컴퓨터 작업을 시작하기 전에 분리한 모든 외부 장치, 주변 장치 및 케이블을 컴퓨터에 연결합니다. 3 컴퓨터 작업을 시작하기 전에 분리한 모든 미디어 카드, 디스크 및 기타 부품을 다시 장착합니다. 4 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 5 컴퓨터를 켭니다.
3 안전 지침 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 경고: 컴퓨터 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어보십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 경고: 컴퓨터 덮개 및 패널을 열기 전에 전원을 모두 분리합니다. 컴퓨터 내부에서 작업한 후 전기 콘센트에 연결하기 전에 덮개, 패널 및 나사를 모두 장착합니다. 주의: 컴퓨터의 손상을 방지하려면 작업 표면이 평평하고 깨끗한지 확인합니다. 주의: 구성 요소 및 카드의 손상을 방지하려면 구성 요소 및 카드를 잡을 때 핀이나 단자를 잡지 말고 모서리를 잡습니다. 주의: Dell 기술 지원 팀에서 승인하거나 지시한 경우에만 문제 해결 및 수리 작업을 수행해야 합니다. Dell사에서 공인하지 않은 서비스로 인한 손상에 대해서는 보상하지 않습니다.
• 정전기에 민감한 구성 요소의 포장을 푸는 경우, 부품 설치 준비를 한 후 정전기 방지 포장재에서 제품을 꺼내십시오. 정전기 방지 패키징을 풀려면 먼저 몸에 있는 정전기를 모두 제거해야 합니다. • 정전기에 민감한 구성 요소를 운반하기 전에 정전기 방지 용기나 포장재에 넣습니다. ESD 현장 서비스 키트 모니터링되지 않는 현장 서비스 키트는 가장 일반적으로 사용되는 서비스 키트입니다. 각 현장 서비스 키트에는 정전기 방지 처리된 매트, 손목 스트랩, 결합 와이어라는 3가지 주요 구성요소가 포함되어 있습니다. ESD 현장 서비스 키트의 구성요소 ESD 현장 서비스 키트의 구성요소는 다음과 같습니다. • 정전기 방지 처리된 매트 - 정전기 방지 처리된 매트는 제전 성질을 띠므로 서비스 절차 중에 부품을 위에 놓을 수 있습니다.
장비 들어 올리기 무거운 장비를 들어 올릴 때는 다음 지침을 따르십시오. 주의: 50파운드보다 무거운 장비를 들어 올리지 마십시오. 항상 다른 사람에게 도움을 요청하거나 기계 인양 장치를 사용하십시 오. 1 발을 바닥에 안정적으로 딛습니다. 발 사이를 벌려서 안정적인 자세를 취하고 발가락을 바깥쪽으로 향합니다. 2 배에 힘을 줍니다. 장비를 들어 올릴 때 배의 근육이 허리를 받쳐주어 장비 무게의 균형을 조절할 수 있습니다. 3 허리가 아닌 다리를 사용하여 들어 올립니다. 4 장비에 몸을 바짝 붙입니다. 허리 쪽에 가까이 붙일수록 허리에 가해지는 부담이 줄어듭니다. 5 장비를 들어 올리든 내려 놓든 허리를 바로 세웁니다. 몸의 무게를 장비에 싣지 않습니다. 몸과 등을 비틀지 않습니다. 6 장비를 내릴 때에는 이 지침의 역순을 따르십시오.
4 권장 도구 이 문서의 절차를 수행하기 위해 다음 도구가 필요할 수 있습니다.
5 나사 목록 표 1. 나사 목록 구성 요소 고정 위치 나사 유형 수량 베이스 덮개 손목 받침대 조립품 M2x5 6 배터리 손목 받침대 조립품 M2x3 5 무선 카드 브래킷 시스템 보드 M2x3 1 하드 드라이브 조립품 손목 받침대 조립품 M2x3 3 SSD 손목 받침대 및 키보드 어 셈블리 M2x3 1 터치패드 브래킷 손목 받침대 조립품 M2x3 3 터치패드 손목 받침대 조립품 M2x2 4 팬 손목 받침대 조립품 M2x3 2 디스플레이 힌지 손목 받침대 조립품 M2.5x5 4 전원 어댑터 포트 손목 받침대 조립품 M2x3 1 I/O 보드 손목 받침대 조립품 M2x3 1 지문 판독기가 장착된 전 원 버튼 손목 받침대 조립품 M3x3 2 시스템 보드 손목 받침대 조립품 M2x2 2 키보드 브래킷 키보드 M1.2x1.4 14 키보드 손목 받침대 조립품 M1.2x1.
6 베이스 덮개 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 베이스 커버를 손목 받침대 어셈블리에 고정하는 6개의 나사(M2x5)를 제거합니다. 2 베이스 커버를 손목 받침대 어셈블리에 고정하는 3개의 조임 나사를 풉니다. 3 플라스틱 스크라이브를 사용하여 힌지에 있는 탭에서 베이스 커버를 들어 올린 후 손목 받침대 어셈블리 슬롯에서 베이스 커버 를 계속해서 들어 올립니다. 4 손목 받침대 어셈블리에서 베이스 커버를 조심스럽게 제거합니다. 주의: 중간에서 베이스 커버를 들어 올리지 마십시오. 섀시가 손상될 수 있습니다.
노트: 다음 단계는 컴퓨터에서 다른 구성 요소를 추가로 제거하려는 경우에만 해당됩니다. 5 시스템 보드에서 배터리 케이블을 분리합니다.
7 베이스 덮개 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 배터리 케이블을 시스템 보드에 연결합니다. 2 베이스 커버의 탭을 손목 받침대 어셈블리 슬롯에 맞춥니다. 3 베이스 커버를 조심스럽게 손목 받침대 어셈블리에서 끼웁니다.
4 베이스 커버를 손목 받침대 어셈블리에 고정하는 3개의 조임 나사를 조입니다. 5 베이스 커버를 손목 받침대 어셈블리에 고정하는 6개의 나사(M2x5)를 장착합니다.
8 배터리 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 배터리 케이블을 시스템 보드에서 연결 해제합니다(이전에 연결 해제하지 않은 경우에만 해당) 2 배터리를 손목 받침대 어셈블리에 고정하는 4개의 나사(M2x3)를 제거합니다. 3 배터리를 들어 올려 손목 받침대 조립품에서 분리합니다. 4 컴퓨터를 뒤집고 디스플레이를 연 후 전원 버튼을 5초간 눌러 시스템 보드를 접지시킵니다.
9 배터리 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 정렬 포스트를 사용하여 배터리를 손목 받침대 어셈블리에 놓습니다. 2 배터리를 손목 받침대 어셈블리에 고정하는 4개의 나사(M2x3)를 장착합니다. 3 배터리 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
10 메모리 모듈 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 마일라를 들어 올려 메모리 모듈에 액세스합니다. 2 메모리 모듈이 튀어 나올 때까지 메모리 모듈 슬롯의 양쪽 끝에 있는 고정 클립을 손끝으로 조심스럽게 벌립니다. 3 메모리 모듈을 밀어 메모리 모듈 슬롯에서 분리합니다.
11 메모리 모듈 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 마일라를 들어 올려 메모리 모듈 슬롯에 액세스합니다. 2 메모리 모듈의 노치를 메모리 모듈 슬롯의 탭에 맞춥니다. 3 메모리 모듈을 메모리 모듈 슬롯 위에서 일정한 각도로 슬롯에 단단히 밀어 넣습니다. 4 딸깍 소리가 나면서 제자리에 고정될 때까지 메모리 모듈을 아래로 누릅니다. 노트: 소리가 나지 않으면 메모리 모듈을 분리했다가 다시 설치합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
12 코인 셀 배터리 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 코인 셀 배터리를 분리하면 BIOS 설정 프로그램 설정을 기본값으로 재설정합니다. 코인 셀 배터리를 제거하기 전에 BIOS 설정 프로그램 설정을 기록하는 것이 좋습니다. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 I/O 보드에서 I/O 보드 케이블을 분리합니다. 2 팬의 라우팅 가이드에서 I/O 보드 케이블을 분리합니다. 3 시스템 보드에서 코인 셀 배터리 케이블을 분리합니다. 4 손목 받침대 조립품에서 코인 셀 배터리를 떼어냅니다.
13 코인 셀 배터리 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 손목 받침대 조립품에 코인 셀 배터리를 부착합니다. 2 시스템 보드에 코인 셀 배터리 케이블을 연결합니다. 3 팬의 라우팅 가이드를 통해 I/O 보드 케이블을 배선합니다. 4 I/O 보드 케이블을 I/O 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
14 팬 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 시스템 보드에서 팬 케이블을 분리합니다. 2 팬을 손목 받침대 어셈블리에 고정하는 2개의 나사(M2x3)를 제거합니다. 3 팬을 들어 올려 손목 받침대 조립품에서 분리합니다.
15 팬 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 정렬 포스트를 사용하여 팬을 손목 받침대 어셈블리에 놓습니다. 2 팬을 손목 받침대 어셈블리에 고정하는 2개의 나사(M2x3)를 교체합니다. 3 팬 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 베이스 덮개를 장착합니다.
16 방열판 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 경고: 방열판은 정상 작동 중에 뜨거워질 수 있습니다. 충분한 시간 동안 방열판을 식힌 후에 만지도록 하십시오. 주의: 프로세서의 최대 냉각 기능을 보장하려면 프로세서 방열판의 열 전달 영역을 만지지 마십시오. 피부에 묻어있는 오일은 열 그리스의 열 전달 기능을 저하시킬 수 있습니다. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 팬을 분리합니다. 절차 1 방열판 조립품에 표시된 번호 순서대로 방열판을 시스템 보드에 고정하는 7개의 조임 나사를 풉니다.
17 방열판 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 방열판을 잘못 맞추면 시스템 보드 및 프로세서가 손상될 수 있습니다. 노트: 시스템 보드 또는 방열판을 장착할 경우 키트에 제공된 열 패드를 사용하여 열 전도성을 확보합니다. 절차 1 방열판의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다. 2 방열판 조립품에 표시된 번호 순서대로 방열판 조립품을 시스템 보드에 고정하는 7개의 조임 나사를 조입니다. 작업후 필수 조건 1 팬을 장착합니다. 2 베이스 덮개를 장착합니다.
18 하드 드라이브 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 주의: 데이터 손실 위험이 있으므로 컴퓨터가 켜져 있거나 절전 모드인 상태에서 하드 드라이브를 분리하지 마십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 절차 1 래치를 열고 시스템 보드에서 하드 드라이브 케이블을 분리합니다. 2 하드 드라이브 어셈블리를 손목 받침대 어셈블리에 고정하는 3개의 나사(M2x3)를 제거합니다.
5 하드 드라이브 브래킷을 하드 드라이브에 고정시키는 4개의 나사(M3x3)를 분리합니다. 6 하드 드라이브를 들어 올려 하드 드라이브 브래킷에서 분리합니다.
19 하드 드라이브 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 하드 드라이브는 쉽게 손상될 수 있습니다. 하드 드라이브를 조심스럽게 다룹니다. 절차 1 하드 드라이브를 하드 드라이브 브래킷에 놓습니다. 2 하드 드라이브 브래킷의 나사 구멍을 하드 드라이브의 나사 구멍에 맞추고, 하드 드라이브 브래킷을 하드 드라이브에 고정하는 4 개의 나사(M3x3)를 장착합니다. 3 하드 드라이브 조립품에 인터포저를 연결합니다. 4 하드 드라이브 조립품의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니다.
작업후 필수 조건 1 배터리를 장착합니다. 2 베이스 덮개를 장착합니다.
20 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈 제거 컴퓨터에서 인텔 옵테인 메모리 모듈을 제거하기 전에 인텔 옵테인 메모리를 비활성화해야 합니다. 인텔 옵테인 메모리 비활성화에 대한 자세한 내용은 인텔 옵테인 메모리 비활성화를 참조하십시오. 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 컴퓨터에서 인텔 옵테인 메모리 모듈을 제거하기 전에 인텔 옵테인 메모리를 비활성화해야 합니다. 인텔 옵테인 메모리 비활성화에 대한 자세한 내용은 인텔 옵테인 메모리 비활성화를 참조하십시오. 베이스 덮개를 분리합니다.
솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈 제거
21 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈 교체 인텔 옵테인 메모리 모듈을 장착한 후 인텔 옵테인 메모리를 활성화합니다. 인텔 옵테인 메모리 활성화에 대한 자세한 내용은 인텔 옵 테인 메모리 활성화를 참조하십시오. 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 주의: 솔리드 상태 드라이브는 충격에 약합니다. 솔리드 상태 드라이브를 다룰 때는 주의합니다. 절차 1 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈의 노치를 솔리드 스테이트 드라이브 슬롯의 탭에 맞춥니다.
인텔 옵테인 메모리 모듈을 장착한 후 인텔 옵테인 메모리를 활성화합니다. 인텔 옵테인 메모리 활성화에 대한 자세한 내용은 인텔 옵 테인 메모리 활성화를 참조하십시오. 나사 마운트 이동 절차 이 컴퓨터는 2개의 솔리드 스테이트 드라이브 폼 팩터를 지원합니다. • M.2 2230 • M.2 2280 제거하지 않은 다른 폼 팩터의 솔리드 스테이트 드라이브 교체 시, 나사 마운트 위치 이동에 대한 다음 절차를 참조하십시오. 1 나사 마운트를 손목 받침대 및 키보드 어셈블리에서 제거합니다. 2 나사 마운트를 180도 회전합니다. 3 나사 마운트를 손목 받침대 및 키보드 어셈블리의 다른 나사 마운트 슬롯에 삽입합니다. 4 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈의 노치를 솔리드 스테이트 드라이브 슬롯의 탭에 맞춥니다. 5 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈을 일정한 각도로 솔리드 상태 드라이브 슬롯에 단단히 밀어 넣습니다.
솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈 교체 37
22 스피커 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 절차 1 시스템 보드에서 스피커 케이블을 분리합니다. 2 오른쪽 스피커를 정렬 포스트에서 들어 올리고 손목 받침대 어셈블리의 라우팅 가이드에서 스피커 케이블을 제거합니다. 3 정렬 포스트에서 왼쪽 스피커를 제거하고 스피커를 손목 받침대 어셈블리에서 들어 올립니다.
23 스피커 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 손목 받침대 어셈블리의 정렬 포스트를 사용하여 왼쪽 스피커를 손목 받침대 어셈블리에 놓습니다. 2 손목 받침대 어셈블리의 라우팅 가이드를 통해 스피커 케이블을 배선하고 오른쪽 스피커를 손목 받침대 어셈블리에 놓습니다. 3 시스템 보드에 스피커 케이블을 연결합니다. 작업후 필수 조건 1 배터리를 장착합니다. 2 베이스 덮개를 장착합니다.
24 무선 카드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 베이스 덮개를 분리합니다. 절차 1 시스템 보드에서 무선 카드를 찾습니다. 2 무선 카드 브래킷을 무선 카드와 손목 받침대 어셈블리에 고정하는 나사(M2x3)를 제거합니다. 3 무선 카드 브래킷을 무선 카드에서 분리합니다. 4 무선 카드에서 안테나 케이블을 분리합니다. 5 무선 카드를 밀어서 무선 카드 슬롯 밖으로 빼냅니다.
무선 카드 분리 41
25 무선 카드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 주의: 무선 카드의 손상을 방지하려면 카드 아래에 케이블을 올려 놓지 마십시오. 1 무선 카드에 안테나 케이블을 연결합니다. 다음 표에는 컴퓨터에서 지원되는 무선 카드의 안테나 케이블 색상표가 제공됩니다. 표 2. 안테나 케이블 색상표 무선 카드의 커넥터 안테나 케이블 색상 주(흰색 삼각형) 흰색 보조(검정색 삼각형) 검정색 2 무선 카드의 노치를 무선 카드 슬롯의 탭에 맞춘 후 무선 카드를 일정한 각도로 무선 카드 슬롯에 밀어 넣습니다.
26 디스플레이 조립품 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 절차 1 컴퓨터를 뒤집어 놓고 디스플레이를 완전히 열어 놓습니다. 주의: 컴퓨터를 부드럽고 깨끗한 곳에 두어 디스플레이에 흠집이 생기는 것을 방지합니다. 2 터치 스크린 케이블을 시스템 보드에 고정하는 테이프에서 떼어냅니다. 3 래치를 열고 시스템 보드에서 터치스크린 보드 케이블을 연결 해제합니다.
27 디스플레이 조립품 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 주의: 컴퓨터를 부드럽고 깨끗한 곳에 두어 디스플레이에 흠집이 생기는 것을 방지합니다. 1 디스플레이 어셈블리를 손목 받침대 어셈블리에 놓고 디스플레이 힌지의 나사 구멍을 손목 받침대 어셈블리의 나사 구멍을 맞춥 니다. 2 디스플레이 힌지를 I/O 보드 및 시스템 보드에 고정하는 4개의 나사(M2.5x5)를 장착합니다. 3 손목 받침대 조립품의 배선 가이드를 통해 안테나 케이블을 배선합니다.
28 전원 어댑터 포트 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 절차 1 시스템 보드에서 전원 어댑터 포트 케이블을 분리합니다. 2 전원 어댑터 포트를 손목 받침대 조립품에 고정하는 나사(M2x3)를 분리합니다. 3 전원 어댑터 포트 및 해당 케이블을 들어 올려 손목 받침대 조립품에서 분리합니다.
29 전원 어댑터 포트 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 전원 어댑터 포트를 손목 받침대 조립품의 슬롯에 올려 놓습니다. 2 전원 어댑터 포트의 나사 구멍을 손목 받침대 어셈블리의 나사 구멍에 맞추고 전원 어댑터 포트를 손목 받침대 어셈블리에 고정 하는 나사(M2x3)를 장착합니다. 3 전원 어댑터 포트 케이블을 시스템 보드에 연결합니다. 작업후 필수 조건 1 디스플레이 어셈블리를 장착합니다. 2 방열판을 장착합니다. 3 팬을 장착합니다. 4 무선 카드를 장착합니다. 5 베이스 덮개를 장착합니다.
30 I/O 보드 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 절차 1 래치를 열고 지문 판독기 케이블을 I/O 보드에서 연결 해제합니다. 2 당김 탭을 사용하여 I/O 보드에서 I/O 보드 케이블을 분리합니다. 3 I/O 보드를 손목 받침대 조립품에 고정하는 나사(M2x3)를 분리합니다. 4 I/O 보드를 들어 울려 손목 받침대 조립품에서 분리합니다.
31 I/O 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 I/O 보드의 USB 포트를 손목 받침대 어셈블리의 슬롯에 맞춥니다. 2 I/O 보드의 나사 구멍을 손목 받침대 어셈블리의 나사 구멍에 맞추고 I/O 보드를 손목 받침대 어셈블리에 고정하는 나사(M2x3) 를 장착합니다. 3 I/O 보드 케이블을 I/O 보드에 연결하고 래치를 닫아 케이블을 고정합니다. 4 지문 판독기 케이블을 I/O 보드 커넥터에 연결하고 래치를 닫아 케이블을 고정합니다. 작업후 필수 조건 1 디스플레이 어셈블리를 장착합니다. 2 방열판을 장착합니다.
32 지문 판독기가 장착된 전원 버튼 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 지문 판독기와 함께 제공된 컴퓨터만 해당됩니다. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 I/O 보드를 분리합니다. 절차 1 래치를 열고 지문 판독기 케이블을 전원 버튼 보드에서 연결 해제합니다. 2 전원 버튼 보드를 손목 받침대 조립품에 고정시키는 테이프를 벗겨 냅니다.
33 지문 판독기가 장착된 전원 버튼 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 지문 판독기와 함께 제공된 컴퓨터만 해당됩니다. 절차 1 전원 버튼 보드의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니다. 2 전원 버튼 보드를 손목 받침대 어셈블리에 고정하는 2개의 나사(M3x3)를 장착합니다. 3 지문 판독기 케이블을 전원 버튼 보드에 연결하고 래치를 닫아 케이블을 고정합니다. 4 전원 버튼 보드를 손목 받침대에 고정하는 테이프를 부착합니다. 작업후 필수 조건 1 I/O 보드를 장착합니다. 2 디스플레이 어셈블리를 장착합니다.
34 시스템 보드 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 노트: 시스템 보드에서 케이블을 분리하기 전에 커넥터의 위치를 기록하여 시스템 보드를 교체한 후에 정확하게 다시 연결할 수 있도록 합니다. 필수 구성 요소 1 베이스 덮개를 분리합니다.
9 시스템 보드를 손목 받침대 어셈블리에 고정시키는 2개의 나사(M2x2)를 제거합니다. 10 시스템 보드를 밀었다가 들어 올려 손목 받침대 어셈블리에서 분리합니다.
35 시스템 보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 노트: 해당 컴퓨터의 서비스 태그는 시스템 보드에 저장되어 있습니다. 시스템 보드를 장착한 후 BIOS 설정 프로그램에서 서비스 태그를 입력해야 합니다. 노트: 시스템 보드를 교체하면 BIOS 설정 프로그램을 사용하여 변경된 BIOS 변경사항이 모두 제거됩니다. 시스템 보드를 교체한 후에는 적절히 변경해야 합니다. 절차 1 시스템 보드의 I/O 포트를 손목 받침대 어셈블리의 슬롯에 밀어 넣습니다.
작업후 필수 조건 1 디스플레이 어셈블리를 장착합니다. 2 방열판을 장착합니다. 3 팬을 장착합니다. 4 솔리드 스테이트 드라이브/인텔 옵테인을 장착합니다. 5 무선 카드를 장착합니다. 6 메모리 모듈을 장착합니다. 7 베이스 덮개를 장착합니다. BIOS 설치 프로그램에 서비스 태그 입력 1 컴퓨터를 켜거나 다시 시작합니다. 2 Dell 로고가 표시되면 F2 키를 눌러 BIOS 설치 프로그램에 접속합니다. 3 Main(기본) 탭으로 이동해 Service Tag Input(서비스 태그 입력) 필드에 서비스 태그를 입력합니다. 노트: 서비스 태그는 컴퓨터의 후면에 있는 영숫자 식별자입니다.
36 터치패드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 절차 1 터치 패드 브래킷을 손목 받침대 어셈블리에 고정하는 3개의 나사(M2x3)를 제거합니다. 2 터치패드 브래킷을 들어올려 손목 받침대 조립품에서 분리합니다. 3 래치를 열고 터치 패드 어셈블리에서 터치패드 케이블을 연결 해제합니다. 4 터치패드 어셈블리를 손목 받침대 어셈블리에 고정하는 테이프를 떼어냅니다. 5 터치패드를 손목 받침대 어셈블리에 고정하는 4개의 나사(M2x2)를 제거합니다.
37 터치패드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 터치 패드의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니다. 2 터치패드를 손목 받침대 어셈블리에 고정하는 4개의 나사(M2x2)를 장착합니다. 3 터치패드 어셈블리를 손목 받침대 어셈블리에 고정시키는 테이프를 부착합니다. 4 터치패드 케이블을 터치패드 어셈블리 밀어 넣은 후 래치를 닫아 케이블을 고정합니다. 5 터치 패드 브래킷의 나사 구멍을 손목 받침대 어셈블리의 나사 구멍에 맞춥니다.
38 키보드 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 3 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈을 제거합니다. 4 메모리 모듈을 분리합니다. 5 하드 드라이브를 분리합니다. 6 코인 셀 배터리를 분리합니다. 7 무선 카드를 분리합니다. 8 스피커를 분리합니다. 9 팬을 분리합니다. 10 방열판을 분리합니다. 11 디스플레이 어셈블리를 분리합니다. 12 전원 어댑터 포트를 분리합니다. 13 I/O 보드를 분리합니다.
4 키보드를 손목 받침대 어셈블리에 고정하는 14개의 나사(M1.2x1.5)를 제거합니다. 5 키보드를 들어 올려 손목 받침대 조립품에서 분리합니다.
39 키보드 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 키보드의 나사 구멍을 손목 받침대 조립품의 나사 구멍에 맞춥니다. 2 키보드를 손목 받침대 어셈블리에 고정하는 14개의 나사(M1.2x1.5)를 장착합니다. 3 키보드 브래킷의 나사 구멍을 키보드 나사 구멍에 맞춥니다. 4 키보드 브래킷을 키보드에 고정하는 14개의 나사(M1.4x2)를 장착합니다. 5 키보드 브래킷을 키보드에 고정하는 테이프를 부착합니다.
작업후 필수 조건 1 터치패드를 장착합니다. 2 시스템 보드를 장착합니다. 3 지문 판독기가 장착된 전원 버튼을 장착합니다. 4 I/O 보드를 장착합니다. 5 전원 어댑터 포트를 장착합니다. 6 디스플레이 어셈블리를 장착합니다. 7 방열판을 장착합니다. 8 팬을 장착합니다. 9 스피커를 장착합니다. 10 무선 카드를 장착합니다. 11 코인 셀 배터리를 장착합니다. 12 하드 드라이브를 장착합니다. 13 메모리 모듈을 장착합니다. 14 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈을 장착합니다. 15 배터리를 장착합니다. 16 베이스 덮개를 장착합니다.
40 손목 받침대 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 배터리를 분리합니다. 3 메모리 모듈을 분리합니다. 4 코인 셀 배터리를 분리합니다. 5 팬을 분리합니다. 6 방열판을 분리합니다. 7 하드 드라이브를 분리합니다. 8 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈을 제거합니다. 9 스피커를 분리합니다. 10 무선 카드를 분리합니다. 11 디스플레이 어셈블리를 분리합니다. 12 전원 어댑터 포트를 분리합니다. 13 I/O 보드를 분리합니다.
41 손목 받침대 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 손목 받침대를 평평한 표면에 놓습니다. 작업후 필수 조건 1 키보드를 장착합니다. 2 터치패드를 장착합니다. 3 시스템 보드를 장착합니다. 4 지문 판독기가 장착된 전원 버튼을 장착합니다. 5 I/O 보드를 장착합니다. 6 전원 어댑터 포트를 장착합니다. 7 디스플레이 어셈블리를 장착합니다. 8 무선 카드를 장착합니다. 9 스피커를 장착합니다. 10 솔리드 스테이트 드라이브/인텔 옵테인 메모리 모듈을 장착합니다. 11 하드 드라이브를 장착합니다.
42 디스플레이 패널 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 노트: SR 테이프 및 압력 필름을 사용한 디스플레이 패널 부품 조각 장착은 RFR(Return For Repair - Depot/CIS/CAR/MIS) 서비 스 건만으로 국한됩니다. 완성된 디스플레이 어셈블리(LCD 힌지업 디스플레이 어셈블리)는 현장 서비스 건에 대해서만 발송되 어야 합니다. 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다.
6 디스플레이 패널을 들어 올려 디스플레이 후면 덮개 및 안테나 조립품에서 분리합니다. 7 카메라를 분리합니다. 8 디스플레이 케이블을 분리합니다. 9 위의 절차를 모두 수행하고 나면 디스플레이 패널이 남습니다.
디스플레이 패널 분리 65
43 디스플레이 패널 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 디스플레이 패널을 평평하고 깨끗한 표면에 놓습니다. 2 디스플레이 케이블을 장착합니다. 3 카메라를 장착합니다. 4 SR 테이프에서 릴리즈 종이를 제거합니다.
5 2개의 SR 테이프를 디스플레이 후면 커버 및 안테나 어셈블리의 플라스틱 가장자리에 맞추고 붙입니다. 6 SR 테이프의 파란색 릴리즈 종이를 제거합니다. 7 디스플레이 패널의 상단을 디스플레이 후면 커버 및 안테나 어셈블리에 밀어 넣고 디스플레이 패널을 디스플레이 후면 커버 및 안테나 어셈블리에 놓습니다. 8 디스플레이 패널을 디스플레이 후면 커버와 안테나 어셈블리에 고정시키는 2개의 나사(M2x3)를 장착합니다. 9 디스플레이 힌지에 있는 라우팅 가이드를 통해 디스플레이 케이블 및 터치스크린 보드 케이블을 배선합니다. 10 디스플레이 베젤을 디스플레이 후면 커버 및 안테나 어셈블리에 놓고 제자리에 끼웁니다.
11 압력 필름에서 릴리즈 종이를 제거합니다. 12 압력 필름을 디스플레이 패널에 부착합니다. 13 플라스틱 스크라이브의 평평한 끝으로 빨간색이 될 때까지 압력 필름을 누릅니다. 14 디스플레이 패널에서 압력 필름을 벗겨 냅니다.
작업후 필수 조건 1 디스플레이 어셈블리를 장착합니다. 2 방열판을 장착합니다. 3 팬을 장착합니다. 4 무선 카드를 장착합니다. 5 베이스 덮개를 장착합니다.
44 카메라 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 "디스플레이 패널 제거"의 1단계부터 6단계를 수행합니다. 절차 1 플라스틱 스크라이브를 사용하여 카메라 모듈을 디스플레이 패널 어셈블리에서 조심스럽게 풉니다. 2 카메라 모듈이 검은색 접착 테이프에서 분리되고 카메라 케이블이 카메라 모듈에서 연결 해제될 때까지 롤 오버합니다.
45 카메라 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 카메라 케이블을 카메라 모듈에 연결합니다. 2 정렬 포스트를 사용하여 카메라를 디스플레이 패널 조립품에 부착합니다. 작업후 필수 조건 1 "디스플레이 패널 장착"의 4단계부터 9단계를 수행합니다. 2 디스플레이 어셈블리를 장착합니다. 3 방열판을 장착합니다. 4 팬을 장착합니다. 5 무선 카드를 장착합니다. 6 베이스 덮개를 장착합니다.
46 디스플레이 힌지 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 디스플레이 패널을 분리합니다. 절차 1 힌지를 디스플레이 후면 커버에 고정하는 6개의 나사(M2.5x2.5)를 제거합니다. 2 안테나 케이블을 디스플레이 후면 커버의 라우팅 가이드에서 제거합니다. 3 힌지와 브래킷을 들어 올려 디스플레이 후면 커버에서 분리합니다.
47 디스플레이 힌지 장착 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 힌지와 브래킷의 나사 구멍을 디스플레이 후면 커버의 나사 구멍에 맞춥니다. 2 안테나 케이블을 디스플레이 후면 덮개의 라우팅 가이드에 배선합니다. 3 힌지를 디스플레이 후면 커버에 고정하는 나사 6개(M2.5x2.5)를 장착합니다. 작업후 필수 조건 1 디스플레이 패널을 장착합니다. 2 디스플레이 어셈블리를 장착합니다. 3 방열판을 장착합니다. 4 팬을 장착합니다. 5 무선 카드를 장착합니다. 6 베이스 덮개를 장착합니다.
48 디스플레이 케이블 분리 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 "디스플레이 패널 제거"의 1단계부터 6단계를 수행합니다. 7 카메라를 분리합니다. 절차 1 카메라 케이블을 디스플레이 패널에 고정하는 테이프를 떼어냅니다. 2 래치를 열고 카메라 케이블을 디스플레이 패널 커넥터에서 연결 해제합니다.
49 디스플레이 케이블 교체 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 1 디스플레이 케이블을 연결하고 래치를 닫아 케이블을 고정합니다. 2 카메라 케이블 및 터치스크린 보드 케이블을 디스플레이 패널에 부착합니다. 3 터치스크린 보드 케이블을 연결하고 래치를 닫아 케이블을 고정합니다. 4 터치스크린 보드 케이블을 디스플레이 패널에 고정하는 테이프를 부착합니다. 5 카메라 케이블을 연결하고 래치를 닫아 케이블을 고정합니다. 6 카메라 케이블을 디스플레이 패널에 고정하는 테이프를 부착합니다. 작업후 필수 조건 1 카메라를 장착합니다.
50 디스플레이 후면 커버 제거 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 필수 구성 요소 1 베이스 덮개를 분리합니다. 2 무선 카드를 분리합니다. 3 팬을 분리합니다. 4 방열판을 분리합니다. 5 디스플레이 어셈블리를 분리합니다. 6 디스플레이 패널을 분리합니다. 7 디스플레이 힌지를 분리합니다. 절차 모든 필수 조건을 수행하고 나면 가 남습니다.
51 디스플레이 힌지 후면 커버 교체 경고: 컴퓨터 내부에서 작업하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어 보고 컴퓨터 내부 작업을 시작하기 전에의 단계를 따르십시오. 컴퓨터 내부 작업을 마친 후에 컴퓨터 내부 작업을 마친 후에의 지침을 따르십시오. 추가 안전 모범 사례는 Regulatory Compliance(규정 준수) 홈페이지(www.dell.com/regulatory_compliance)를 참조하십시오. 절차 를 평평한 표면에 둡니다. 작업후 필수 조건 1 디스플레이 힌지를 장착합니다. 2 디스플레이 패널을 장착합니다. 3 디스플레이 어셈블리를 장착합니다. 4 방열판을 장착합니다. 5 팬을 장착합니다. 6 무선 카드를 장착합니다. 7 베이스 덮개를 장착합니다.
52 장치 드라이버 Intel 칩셋 소프트웨어 설치 유틸리티 장치 관리자에서 칩셋 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 칩셋 업데이트를 설치합니다. 비디오 드라이버 장치 관리자에서 비디오 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 비디오 드라이버 업데이트를 설치합니다. 인텔 직렬 IO 드라이버 장치 관리자에서 인텔 직렬 IO 드라이버가 설치되어 있는지 확인합니다. www.dell.com/support에서 드라이버 업데이트를 설치합니다. Intel Trusted Execution 엔진 인터페이스 장치 관리자에서 Intel Trusted Execution 엔진 인터페이스 드라이버가 설치되었는지 확인합니다. www.dell.com/support에서 드라이버 업데이트를 설치합니다. 인텔 가상 버튼 드라이버 장치 관리자에서 Intel Virtual Button 드라이버가 설치되어 있는지 확인합니다. www.dell.
53 시스템 설정 노트: 컴퓨터 및 설치된 장치에 따라 이 섹션에 나열된 항목이 표시될 수도 있고 표시되지 않을 수도 있습니다. Boot Sequence(부팅 순서) 부팅 순서를 사용하여 시스템 설치가 정의하는 부팅 장치 순서를 생략하고 직접 특정 장치(예: 광학 드라이브 또는 하드 드라이브)로 부팅할 수 있습니다. 전원 켜기 자체 테스트(POST) 중에 Dell 로고가 나타나면 다음과 같은 작업을 수행할 수 있습니다. • F2 키를 눌러 시스템 설정에 액세스 • F12 키를 눌러 1회 부팅 메뉴 실행 부팅할 수 있는 장치가 진단 옵션과 함께 원타임 부팅 메뉴에 표시됩니다. 부팅 메뉴 옵션은 다음과 같습니다. • 이동식 드라이브(사용 가능한 경우) • STXXXX 드라이브 노트: XXX는 SATA 드라이브 번호를 표시합니다. • 광학 드라이브(사용 가능한 경우) • SATA 하드 드라이브(해당하는 경우) • 진단 노트: 진단을 선택하면, ePSA 진단 화면이 표시됩니다.
노트: BIOS 설정 프로그램을 변경하기 전에 나중에 참조할 수 있도록 BIOS 설정 프로그램 화면 정보를 기록해 두는 것이 좋습니 다. BIOS 설정 프로그램을 사용하여 다음과 같은 작업을 수행합니다. • 해당 컴퓨터에 설치된 하드웨어 정보 찾기(예: RAM 크기, 하드 드라이브 크기 등) • 시스템 구성 정보를 변경합니다 • 사용자 선택 가능한 옵션 설정 또는 변경(예: 사용자 암호, 설치된 하드 드라이브 유형, 기본 장치 사용 또는 사용 안 함 등) BIOS 설정 프로그램 시작하기 1 컴퓨터를 켜거나 다시 시작합니다. 2 POST 중에 DELL 로고가 표시되면 F2 프롬프트가 표시되는 즉시 F2 키를 누릅니다. 노트: F2 프롬프트는 키보드가 초기화되었다는 것을 나타냅니다. 이 프롬프트는 잠깐만 나타나므로, 표시되는지 잘 살폈다 가 F2키를 누릅니다. F2 프롬프트가 나타나기 전에 F2 키를 누르면 이 키 입력이 손실됩니다.
General-System Information Maximum Clock Speed 프로세서의 최대 클럭 속도를 표시합니다. Processor L2 Cache 프로세서 L2 캐시 크기를 표시합니다. Processor L3 Cache 프로세서 L3 캐시 크기를 표시합니다. HT Capable 프로세서가 하이퍼스레드(HT)가 가능한지 여부를 표시합니다. 64-Bit Technology 64비트 기술을 사용하는지 여부를 표시합니다. 장치 정보 SATA-0 컴퓨터의 M.2 SATA SSD-0 디바이스 정보를 표시합니다. SATA-1 컴퓨터의 M.2 SATA SSD-1 디바이스 정보를 표시합니다. M.2 PCIe SSD-0 컴퓨터의 M.2 PCIe SSD-0 디바이스 정보를 표시합니다. M.2 PCIe SSD-1 컴퓨터의 M.2 PCIe SSD-1 디바이스 정보를 표시합니다. 비디오 컨트롤러 컴퓨터의 비디오 컨트롤러 유형을 표시합니다.
시스템 구성 Enable External USB Port 외부 USB 포트에 연결된 USB 대용량 스토리지 장치에서의 부팅을 활성화 또는 비 활성화합니다. 오디오 내장형 오디오 컨트롤러를 활성화 또는 비활성화합니다. Keyboard Illumination 키보드 조명 기능의 작동 모드를 선택할 수 있습니다. Keyboard Backlight Timeout on AC 이 기능은 AC 어댑터가 컴퓨터에 연결되어 있는 경우 키보드 백라이트의 시간 제 한 값을 정의합니다. Keyboard Backlight Timeout on Battery 이 기능은 컴퓨터가 배터리 전원으로 실행될 때 키보드 백라이트의 시간 제한 값을 정의합니다. Miscellaneous Devices 다양한 온보드 장치를 활성화 또는 비활성화할 수 있습니다. 표 5. 시스템 설치 옵션—비디오 메뉴 비디오 LCD Brightness 배터리 및 AC 전원과 별개로 패널 밝기를 설정합니다.
표 7. 시스템 설치 옵션—보안 부팅 메뉴 보안 부팅 Secure Boot Enable 보안 부팅 기능을 활성화 또는 비활성화합니다. Secure Boot Mode 보안 부팅의 동작을 수정하여 UEFI 드라이버 시그니처를 평가 또는 적용할 수 있습 니다. Expert Key Management Expert Key Management 전문 키 관리 기능을 활성화 또는 비활성화합니다. Custom Mode Key Management 전문 키 관리에 대한 사용자 지정 값을 선택합니다. 표 8. 시스템 설치 옵션—Intel 소프트웨어 가드 확장 메뉴 인텔 소프트웨어 가드 확장 Intel SGX Enable Intel 소프트웨어 가드 확장자를 활성화 또는 비활성화합니다. Enclave Memory Size Intel 소프트웨어 가드 확장자 인클레이브 전용 메모리 크기를 설정합니다. 성능 Multi Core Support 여러 코어를 활성화합니다. 기본값: 활성화.
인텔 소프트웨어 가드 확장 POST 동작 Adapter Warnings 어댑터 경고를 활성화 또는 비활성화합니다. 기본값: 활성화. Numlock Enable 컴퓨터 부팅 시 NumLock 기능을 활성화합니다. Fn Lock Options Fn 잠금 모드를 활성화 또는 비활성화합니다. Fastboot 부팅 프로세스의 속도를 설정합니다. 기본: 전체 Extend BIOS POST Time 추가 사전 부팅 지연을 구성합니다. 전체 화면 로고 전체 화면 로고 표시를 활성화 또는 비활성화합니다. Warnings and Errors 경고 또는 오류가 감지되는 경우 부팅 프로세스를 일시 중지하도록 설정합니다. 표 9. 시스템 설치 옵션—가상화 지원 메뉴 가상화 지원 Virtualization VMM(Virtual Machine Monitor)이 Intel 가상화 기술이 제공하는 추가 하드웨어 기능 을 활용할지 여부를 지정합니다.
표 13. 시스템 설치 옵션—SupportAssist 시스템 해상도 SupportAssist 시스템 해상도 Auto OS Recovery Threshold(자동 OS 복구 임계값) SupportAssist 시스템 해상도 콘솔 및 Dell OS 복구 도구에 대한 자동 부팅 흐름을 제어합니다. SupportAssist OS Recovery(SupportAssist OS 복구) 특정 시스템 오류에서의 SupportAssist OS 복구 도구에 대한 자동 부팅 흐름까지 제어합니다. CMOS 설정 지우기 주의: CMOS 설정 지우기를 통해 컴퓨터의 BIOS 설정을 재설정할 수 있습니다. 1 베이스 덮개를 분리합니다. 2 시스템 보드에서 배터리 케이블을 분리합니다. 3 코인 셀 배터리를 분리합니다. 4 1분간 기다립니다. 5 코인 셀 배터리를 장착합니다. 6 배터리 케이블을 시스템 보드에 연결합니다. 7 베이스 덮개를 장착합니다.
54 문제 해결 BIOS 플래싱 사용 가능한 업데이트가 있거나 시스템 보드 교체 후 BIOS를 플래싱(업데이트)해야 할 수 있습니다. BIOS를 업데이트하려면 다음 단계를 따릅니다. 1 컴퓨터를 켭니다. 2 www.dell.com/support로 이동합니다. 3 Product support(제품 지원)을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 4 Drivers & Downloads(드라이버 및 다운로드) > Find it myself(직접 찾기)를 클릭합니다. 5 컴퓨터에 설치된 운영 체제를 선택합니다. 6 페이지를 아래로 스크롤하여 BIOS를 확장할 수 있습니다. 7 Download(다운로드)을 클릭하여 컴퓨터 BIOS의 최신 버전을 다운로드합니다. 8 다운로드가 완료된 후 BIOS 업데이트 파일을 저장한 폴더로 이동합니다. 9 BIOS 업데이트 파일 아이콘을 두 번 클릭하고 화면의 지침을 따릅니다.
자세한 내용은 Dell EPSA 진단 3.0을 참조하십시오. ePSA 진단 실행 1 컴퓨터를 켭니다. 2 컴퓨터가 부팅될 때 Dell 로고가 나타나면 F12 키를 누릅니다. 3 부팅 메뉴 화면에서 Diagnostics(진단) 옵션을 선택합니다. 4 왼쪽 하단의 화살표를 클릭합니다. 진단 전면 페이지가 표시됩니다. 오른쪽 하단 모서리의 화살표를 클릭하여 페이지 목록으로 이동합니다. 5 감지된 항목이 나열됩니다. 6 특정 장치에서만 진단 테스트를 실행하려면 Esc를 누른 다음 Yes(예)를 눌러 진단 테스트를 중지합니다. 7 왼쪽 창에서 장치를 선택하고 Run Tests(테스트 실행)을 클릭합니다. 8 문제가 발생하면 오류 코드가 표시됩니다. 오류 코드와 인증 번호를 확인하고 Dell사에 문의하십시오. 시스템 진단 표시등 전원 및 배터리 상태 표시등/하드 드라이브 작동 표시등 배터리 충전 상태 또는 하드 드라이브 작동을 나타냅니다.
표 14. 진단 표시등 패턴 문제 설명 2,1 CPU 오류 2,2 시스템 보드: BIOS 및 ROM 장애 2,3 메모리 또는 RAM이 발견되지 않음 2,4 메모리 또는 RAM 장애 2,5 잘못된 메모리 설치 2,6 시스템 보드 또는 칩셋 오류 2,7 LCD 장애 3,1 CMOS 배터리 오류 3,2 PCI 또는 비디오 카드 또는 칩 오류 3,3 복구 이미지를 찾을 수 없음 3,4 복구 이미지를 찾았지만 유효하지 않음 3,5 전원 레일 오류 3,6 SBIOS 플래시 손상 3,7 HECI 메시지에 회신하기 위하여 ME에서 타임아웃 대기 카메라 상태 표시등: 카메라가 사용 중인지 여부를 나타냅니다. • 흰색으로 켜짐 - 카메라가 사용 중입니다. • 꺼짐 - 카메라가 사용 중이 아닙니다. Caps Lock 상태 표시등: Caps Lock가 활성화되어 있는지 또는 비활성화되어 있는지 여부를 나타냅니다.
3 Intel Optane Memory(Intel Optane 메모리) 탭에서 Disable(비활성화)를 클릭하여 Intel Optane 메모리를 비활성화합니다. 4 경고를 수락하는 경우 Yes(예)를 클릭합니다. 비활성화 진행률이 표시됩니다. 5 Reboot(재부팅)을 클릭하여 Intel Optane 메모리의 비활성화를 완료하고 컴퓨터를 다시 시작합니다. Wi-Fi 전원 주기 Wi-Fi 연결 문제로 인해 컴퓨터에서 인터넷에 액세스할 수 없는 경우 Wi-Fi 전원 주기 절차를 수행할 수 있습니다. 다음 절차는 Wi-Fi 전 원 주기를 수행하는 방법에 대한 지침을 제공합니다. 노트: 일부 ISP(Internet Service Providers)는 모뎀/라우터 콤보 디바이스를 제공합니다. 1 컴퓨터를 끕니다. 2 모뎀을 끕니다. 3 무선 라우터를 끕니다. 4 약 30초간 기다립니다. 5 무선 라우터를 켭니다. 6 모뎀을 켭니다. 7 컴퓨터를 켭니다.