Inspiron 7590 دليل الخدمة النموذج الرقابيP83F : النوع الرقابيP83F001 :
الملاحظات والتنبيهات والتحذيرات ملاحظة تشير كلمة "ملاحظة" إلى معلومات هامة تساعدك على تحقيق أقصى استفادة من المنتج الخاص بك. تنبيه تشير كلمة "تنبيه" إلى احتمال حدوث تلف بالأجهزة أو فقد للبيانات وت ُعلمك بكيفية تجنب المشكلة. تحذير تشير كلمة "تحذير" إلى احتمال حدوث تلف بالممتلكات أو وقوع إصابة شخصية أو الوفاة. حقوق النشر © 2019لشركة Dell Inc.أو الشركات التابعة لها .جميع الحقوق محفوظة .علامة Dellو EMCوالعلامات التجارية الأخرى هي علامات تجارية لشركة Dell Inc.
جدول المحتويات 1إرشادات الأمان6 .................................................................................................................................... قبل العمل داخل الكمبيوتر6 ................................................................................................................................................................ قبل البدء7.......................................................................................................................................
تركيب مروحة وحدة معالجة الرسومات33 ...................................................................................................................................... المشتت الحراري34 ......................................................................................................................................................................... إزالة المشتت الحراري 34 .........................................................................................................................
إعداد النظام69 ................................................................................................................................................................................ الدخول إلى برنامج إعداد 69 .....................................................................................................................................................BIOS مفاتيح التنقل69 .................................................................................................................
1 إرشادات الأمان المتطلبات استعن بإرشادات السلامة التالية لحماية جهاز الكمبيوتر الخاص بك من أي تلف محتمل وضمان سلامتك الشخصية .ما لم يتم الإشارة إلى غير ذلك ،فإن كل إجراء متضمن في هذا المستند يفترض وجود الظروف التالية: • • قيامك بقراءة معلومات الأمان الواردة مع الكمبيوتر. يمكن استبدال أحد المكونات أو ،في حالة شرائه بصورة منفصلة ،تركيبه من خلال اتباع إجراءات الإزالة بترتيب عكسي. عن المهمة ملاحظة قم بفصل جميع مصادر الطاقة قبل فتح غطاء الكمبيوتر أو اللوحات .
قبل البدء الخطوات .1احفظ جميع الملفات المفتوحة وأغلقها وقم بإنهاء جميع التطبيقات المفتوحة. .2قم بإيقاف تشغيل جهاز الكمبيوتر الخاص بك .قم بالنقر على ابدأ < التيار < إيقاف التشغيل. ملاحظة إذا كنت تستخدم نظام تشغيل آخر ،فانظر مستندات نظام التشغيل لديك لمعرفة تعليمات إيقاف التشغيل. .3افصل جهاز الكمبيوتر الخاص بك وكافة الأجهزة المتصلة به من مآخذ التيار الكهربي الخاصة بهم. .
• • • • أفضل طريقة لإجراء هذا الفحص .إذا لم تتوفر لديك أداة اختبار رباط المعصم الخاصة بك ،فارجع إلى المكتب الإقليمي التابع له لمعرفة ما إذا كان يتوفر لديه أداة اختبار .لإجراء الفحص ،قم بتوصيل سلك ربط رباط المعصم بأداة الاختبار مع ربطه حول معصمك ،ثم اضغط على الزر لإجراء الفحص .يضيء مصباح LEDباللون الأخضر إذا كان الفحص ناج ًحا؛ ويضيء مصباح LEDباللون الأحمر ويصدر صوت إنذار إذا فشل الفحص.
2 إزالة المكونات وتركيبها الأدوات الموصى باستخدامها قد تحتاج الإجراءات الواردة في هذا المستند إلى وجود الأدوات التالية: • • • مفك Phillips #1 مفك مسطح مخطاط بلاستيكي قائمة المسامير اللولبية ملاحظة عند إزالة المسامير اللولبية من أحد المكونات ،يوصى بتدوين نوع المسمار وكمية المسامير ،ثم وضعها في علبة تخزين المسامير اللولبية .وذلك للتأكد من صحة عدد المسامير اللولبية واستعادة نوع المسمار اللولبي الصحيح عند إعادة وضع المكون.
نوع المسمار اللولبي الكمية مثبت بـ المكون M1.6x2 2 مروحة وحدة معالجة الرسومات )(GPU مجموعة مسند راحة اليد ولوحة المفاتيح M2x4 2 محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة M.2 2280 لوحة النظام M2x4 2 محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة M.
الخطوات .1قم بإزالة المسامير اللولبية الخمسة ) (M2x5المثبتة لغطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بفك المسامير اللولبية الثلاثة المثبتة لغطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح. .3ارفع غطاء القاعدة لفتحه بد ًءا من الحافة العلوية الوسطى لمجموعه مسند راحة اليد ولوحه المفاتيح واتبع "خط الإرشاد" المشار إليه في الصورة لإزالة غطاء القاعدة. .4ارفع غطاء القاعدة خارج مجموعة مسند راحة اليد ولوحة المفاتيح.
تركيب غطاء القاعدة المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع غطاء القاعدة ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1ضع غطاء القاعدة على مجموعة مسند راحة اليد ولوحة المفاتيح وثبّت غطاء القاعدة في مكانه. .2أحكم ربط المسامير اللولبية الثلاثة المثبتة لغطاء القاعدة في مجموعة مسند راحة اليد ولوحة المفاتيح. .
• احرص على تفريغ شحنة البطارية قدر الإمكان قبل إزالتها من النظام .يمكن إجراء ذلك عن طريق فصل مهايئ التيار المتردد عن النظام للسماح بخروج بتصريف شحنة البطارية. • لا تعمد إلى سحق البطارية أو إسقاطها أوتشويهها أو خرقها باستخدام أشياء خارجية. • احرص على عدم تعريض البطارية لحرارة مرتفعة أو تفكيك علب البطارية وخلاياها. • لا تضغط على سطح البطارية. • لا تعمد إلى ثني البطارية. • لا تستخدم أدوات من أى نوع لخلع البطارية أو تركيبها.
تركيب البطارية ذات 3خلايا المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع البطارية ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1ضع البطارية في مجموعة مسند راحة اليد ولوحة المفاتيح وقم بمحاذاة فتحات المسامير اللولبية الموجودة في البطارية مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .
الخطوات .1افصل كابل البطارية من لوحة النظام. .2قم بإزالة المسامير اللولبية السبعة ) (M2x4المثبتة للبطارية في مجموعة مسند راحة اليد ولوحة المفاتيح. .3ارفع البطارية خارج مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب البطارية ذات 6خلايا المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع البطارية ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1ضع البطارية في مجموعة مسند راحة اليد ولوحة المفاتيح وقم بمحاذاة فتحات المسامير اللولبية الموجودة في البطارية مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .2أعد وضع المسامير اللولبية السبعة ) (M2x4المثبتة للبطارية في مجموعة مسند راحة اليد ولوحة المفاتيح. .3قم بتوصيل كابل البطارية بلوحة النظام. الخطوات التالية .1قم بتركيب غطاء القاعدة. .2اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
الخطوات .1ارفع شريط مايلار واستخدم أطراف أصابعك لفصل مشابك التثبيت الموجودة على طرفي فتحة وحدة الذاكرة بعناية حتى تبرز وحدة الذاكرة للخارج. .2قم بإزاحة وحدة الذاكرة ورفعها عن فتحة وحدة الذاكرة الموجودة في لوحة النظام. تركيب وحدة الذاكرة المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع وحدة الذاكرة ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1ارفع السن الموجود في وحدة الذاكرة وقم بمحاذاته مع اللسان الموجود في فتحة وحدة الذاكرة. .2قم بإزاحة وحدة الذاكرة بثبات داخل الفتحة بزاوية. .3اضغط على وحدة الذاكرة حتى تستقر في مكانها وتصدر تكه. ملاحظة إذا لم تسمع صوت استقرار وحدة الذاكرة في موضعها ،فقم بإزالتها وإعادة تركيبها. الخطوات التالية .1قم بتوصيل كابل البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
الخطوات .1قم بإزالة المسمار اللولبي ) (M2x4الذي يثبت دعامة بطاقة WLANفي بطاقة .WLAN .2قم بإزالة دعامة بطاقة WLANمن بطاقة .WLAN .3قم افصل كابلات الهوائي عن بطاقة .WLAN .4قم بإزاحة بطاقة WLANوإزالتها خارج فتحة بطاقة .WLAN تركيب بطاقة الشبكة اللاسلكية محلية النطاق )(WLAN المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع بطاقة WLANويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1قم بمحاذاة السن الموجود في بطاقة WLANمع اللسان الموجود في فتحة بطاقة ،WLANوأدخل بطاقة WLANبزاوية في فتحة بطاقة .WLAN .2صل كابلات الهوائي ببطاقة .WLAN .3قم بمحاذاة دعامة بطاقة WLANووضعها ببطاقة .WLAN .4أعد وضع المسمار اللولبي ) (M2x4لتثبيت دعامة بطاقة WLANفي بطاقة .WLAN الخطوات التالية .1قم بتركيب البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
الخطوات .1قم بإزالة المسمارين اللولبيين ) (M2x4المثبتين لمحرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة بمجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بإزاحة واقي محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة وإزالته خارج فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .3قم بإزاحة وحدة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة وإزالتها خارج فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. تركيب محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.
يوضح الشكل موقع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1إذا لزم الأمر ،قم بمحاذاة دعامة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة لاستيعاب محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 .2280 .2قم بمحاذاة السن الموجود في وحدة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة مع اللسان الموجود في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .
الخطوات التالية .1قم بتوصيل كابل البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. إزالة محرك أقراص مزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230 المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2قم بإزالة غطاء القاعدة. .3افصل كابل البطارية. عن المهمة يوضح الشكل موقع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.
يوضح الشكل موقع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2230ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1إذا لزم الأمر ،قم بمحاذاة دعامة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة لاستيعاب محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 .2230 .2قم بمحاذاة السن الموجود في وحدة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة مع اللسان الموجود في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .
الخطوات التالية .1قم بتوصيل كابل البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. إزالة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 2280 PCIe المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2قم بإزالة غطاء القاعدة. .3افصل كابل البطارية. عن المهمة يوضح الشكل موقع محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.
الخطوات .1قم بمحاذاة السن الموجود في وحدة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة مع اللسان الموجود في فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .2قم بإزاحة وحدة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة بثبات وبزاوية إلى داخل فتحة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة. .3أعد وضع المسمار اللولبي ) (M2x4الذي يثبت محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة في لوحة النظام. الخطوات التالية .1قم بتوصيل كابل البطارية. .
الخطوات .1افتح المزلاج وافصل كبل لوحة اللمس عن لوحة النظام. .2قم بإزالة المسامير اللولبية الثلاثة ) (M2x4المثبتة لحامل محرك الأقراص الثابتة في مجموعة مسند راحة اليد ولوحة المفاتيح. .3ارفع مجموعة محرك الأقراص الثابتة ،مع الكابل الخاص بها ،خارج مجموعة مسند راحة اليد ولوحة المفاتيح. .4افصل الموزع عن مجموعة محرك الأقراص الثابتة. .5قم بإزالة المسامير اللولبية الأربعة ) (M3x3التي تثبت حامل محرك الأقراص الثابتة في محرك الأقراص الثابتة. .
عن المهمة يوضح الشكل موقع محرك الأقراص الثابتة ويقدم تمثيلاً مرئيًا لإجراء التركيب. ملاحظة يتوفر محرك الأقراص الثابتة فقط في أجهزة الكمبيوتر المزودة ببطارية ذات 3خلايا. الخطوات .1قم بتركيب محرك الأقراص الثابتة في الحامل الخاص به. .
الخطوات التالية .1قم بتوصيل كابل البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مكبرات الصوت إزالة مكبرات الصوت المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2قم بإزالة غطاء القاعدة. .3قم بإزالة البطارية. عن المهمة يوضح الشكل موقع مكبرات الصوت ويقدم تمثيلاً مرئيًا لإجراء الإزالة.
الخطوات .1افصل كابل مكبر الصوت من لوحة النظام. .2انتبه إلى توجيه كابل مكبر الصوت وقم بإزالة كابل مكبر الصوت من أدلة التوجيه الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. ملاحظة لاحظ مكان المثبتات المطاطية قبل رفع مكبرات الصوت. .3ارفع مكبرات الصوت ،مع الكابل الخاص به ،عن مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب مكبرات الصوت المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب.
الخطوات التالية .1قم بتركيب البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مروحة وحدة معالجة الرسومات )(GPU إزالة مروحة وحدة المعالجة المركزية المتطلبات .1اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. .2قم بإزالة غطاء القاعدة. .3قم بإزالة البطارية. عن المهمة يوضح الشكل موقع مروحة وحدة المعالجة المركزية ويقدم تمثيلاً مرئيًا لإجراء الإزالة. الخطوات .
عن المهمة يوضح الشكل موقع مروحة وحدة معالجة الرسومات ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1قم بإزاحة مروحة وحدة معالجة الرسومات ووضعها داخل مجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بمحاذاة فتحات المسامير اللولبية الموجودة في مروحة وحدة معالجة الرسومات مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .3أعد وضع المسمارين اللولبيين ) (M2x4اللذين يتثبتان مروحة وحدة معالجة الرسومات في مجموعة مسند راحة اليد ولوحة المفاتيح. .
الخطوات .1قم بإزالة المسمارين اللولبيين ) (M2x4اللذين يتثبتان مروحة وحدة المعالجة المركزية في مجموعة مسند راحة اليد ولوحة المفاتيح. .2افصل كابل مروحة وحدة المعالجة المركزية عن لوحة النظام. .3قم بإزاحة مروحة وحدة المعالجة المركزية ورفعها خارج مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب مروحة وحدة معالجة الرسومات المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب.
الخطوات .1قم بإزاحة مروحة وحدة المعالجة المركزية ووضعها داخل مجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بمحاذاة فتحات المسامير اللولبية الموجودة في مروحة وحدة المعالجة المركزية مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .3أعد وضع المسمارين اللولبيين ) (M2x4لتثبيت مروحة وحدة المعالجة المركزية في مجموعة مسند راحة اليد ولوحة المفاتيح. .4قم بتوصيل كابل مروحة وحدة المعالجة المركزية بلوحة النظام. الخطوات التالية .1قم بتركيب البطارية. .
الخطوات .1بترتيب تسلسلي )كما هو موضح على المشتت الحراري( ،قم بفك مسامير التثبيت اللولبية التي تثبت المشتت الحراري في لوحة النظام. .2ارفع المشتت الحراري وقم بإزالته خارج مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب المشتت الحراري UMA - المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع المشتت الحراري ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1ضع المشتت الحراري على لوحة النظام ،ثم قم بمحاذاة فتحات المسامير اللولبية الموجودة فى المشتت الحراري مع فتحات المسامير اللولبية الموجودة فى لوحة النظام. .2بترتيب تسلسلي )كما هو موضح على المشتت الحراري( ،أحكم ربط مسامير التثبيت اللولبية التي تثبت المشتت الحراري في لوحة النظام. الخطوات التالية .1 .2 .3 .4 .5 قم بتركيب مروحة وحدة المعالجة المركزية. قم بتركيب مروحة وحدة معالجة الرسومات. قم بتركيب البطارية. قم بتركيب غطاء القاعدة.
الخطوات .1بالترتيب التسلسلي )الموضح على المشتت الحراري( ،قم بفك المسامير اللولبية السبعة المثبتة للمشتت الحراري في لوحة النظام. .2ارفع المشتت الحراري وقم بإزالته بعيدًا عن لوحة النظام. تركيب المشتت الحراري -المنفصل المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع المشتت الحراري ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1ضع المشتت الحراري على لوحة النظام ،ثم قم بمحاذاة فتحات المسامير اللولبية الموجودة فى المشتت الحراري مع فتحات المسامير اللولبية الموجودة فى لوحة النظام. .2بالترتيب التسلسلي )الموضح على المشتت الحراري( ،أحكم ربط المسامير اللولبية السبعة المثبتة للمشتت الحراري في لوحة النظام. الخطوات التالية .1 .2 .3 .4 .5 قم بتركيب مروحة وحدة المعالجة المركزية. قم بتركيب مروحة وحدة المعالجة المركزية. قم بتركيب البطارية. قم بتركيب غطاء القاعدة.
الخطوات .1افصل كابل البطارية الخلوية المصغرة من لوحة ) I/Oالإدخال/الإخراج(. .2انزع البطارية الخلوية المصغرة من مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب البطارية الخلوية المصغرة المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع البطارية الخلوية المصغرة ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1ضع البطارية الخلوية المصغرة بداخل الفتحة الموجودة بمجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بتوجيه كابل البطارية الخلوية المصغرة كما هو موضح وقم بتوصيله بلوحة الإدخال/الإخراج. الخطوات التالية .1قم بتركيب البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. لوحة الإدخال/الإخراج إزالة لوحة الإدخال/الإخراج المتطلبات .1 .2 .3 .
الخطوات .1افتح المزلاج وافصل كابل لوحة ) I/Oالإدخال/الإخراج( عن لوحة ) I/Oالإدخال/الإخراج(. .2افتح المزلاج وافصل كابل قارئ بصمات الأصابع عن لوحة ) I/Oالإدخال/الإخراج(. .3افصل كابل البطارية الخلوية المصغرة من لوحة ) I/Oالإدخال/الإخراج(. .4قم بإزالة المسامير اللولبية الثلاثة ) (M2x3المثبتة للوحة الإدخال/الإخراج في مجموعة مسند راحة اليد ولوحة المفاتيح. .5ارفع لوحة ) I/Oالإدخال/الإخراج( خارج مجموعة مسند راحة اليد ولوحة المفاتيح.
الخطوات .1ضع لوحة ) I/Oالإدخال/الإخراج( على مجموعة مسند راحة اليد ولوحة المفاتيح. .2قم بمحاذاة فتحات المسامير اللولبية الموجودة في لوحة ) I/Oالإدخال/الإخراج( مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح. .3أعد وضع المسامير اللولبية الثلاثة ) (M2x3المثبتة للوحة الإدخال/الإخراج في مجموعة مسند راحة اليد ولوحة المفاتيح. .4قم بتوصيل كابل البطارية الخلوية المصغرة بلوحة ) I/Oالإدخال والإخراج(. .
زر التشغيل مع قارئ بصمات الأصابع الاختياري إزالة زر التشغيل وقارئ بصمات الأصابع الاختياري المتطلبات .1 .2 .3 .4 .5 .6 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. إزالة بطاقة .WLAN قم بإزالة مروحة وحدة معالجة الرسومات. قم بإزالة لوحة الإدخال/الإخراج. عن المهمة يوضح الشكل موقع زر التشغيل المزود بقارئ بصمات أصابع اختياري ويقدم تمثيلاً مرئيًا لإجراء الإزالة. الخطوات .
الخطوات .1باستخدام عمود المحاذاة ،ضع زر التشغيل مع قارئ بصمات الأصابع داخل مجموعة مسند راحة اليد ولوحة المفاتيح. .2أعد وضع المسمارين اللولبيين ) (M1.2x2لتثبيت زر التشغيل مع قارئ بصمات الأصابع في مجموعة مسند راحة اليد ولوحة المفاتيح. الخطوات التالية .1 .2 .3 .4 .5 .6 قم بتركيب لوحة الإدخال/الإخراج. قم بتركيب مروحة وحدة معالجة الرسومات. قم بتركيب بطاقة .WLAN قم بتركيب البطارية. قم بتركيب غطاء القاعدة.
الخطوات .1قم بإزالة المسامير اللولبية الثلاثة ) (M2.5x5التي تثبت مفصلة الشاشة اليسرى بمجموعة مسند راحة اليد ولوحة المفاتيح. .2افتح مفصلات الشاشة بزاوية مقدارها 90درجة. .3قم بإزالة المسمار اللولبي ) (M2x4الذي يثبت منفذ مهايئ التيار بمجموعة مسند راحة اليد ولوحة المفاتيح. .4افصل كابل منفذ مهايئ التيار من لوحة النظام. .5ارفع منفذ مهايئ التيار ،مع الكابل الخاص به ،خارج مجموعة مسند راحة اليد ولوحة المفاتيح.
الخطوات .1قم بتوصيل كابل منفذ مهايئ التيار بلوحة النظام. .2أعد وضع المسمار اللولبي ) (M2x4الذي يثبت منفذ مهايئ التيار بمجموعة مسند راحة اليد ولوحة المفاتيح. .3باستخدام أعمدة المحاذاة ،أغلق مفصلات الشاشة. .4أعد وضع المسامير اللولبية الثلاثة ) (M2.5x5المثبتة لمفصلة الشاشة اليسرى في لوحة النظام. الخطوات التالية .1قم بتركيب البطارية. .2قم بتركيب غطاء القاعدة. .3اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك.
لوحة اللمس إزالة لوحة اللمس المتطلبات .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. قم بإزالة مكبرات الصوت. عن المهمة يوضح الشكل موقع لوحة اللمس ويقدم تمثيلاً مرئيًا لإجراء الإزالة. الخطوات .1قم بإزالة المسامير اللولبية ) (M2x3الثلاثة التي تثبت دعامة لوحة اللمس في مجموعة مسند راحة اليد ولوحة المفاتيح. .
.4أعد وضع المسمارين اللولبيين ) (M1.6x2المثبتين للوحة اللمس في مجموعة مسند راحة اليد ولوحة المفاتيح. .5ارفع لوحة اللمس ،مع الكابل الخاص بها ،عن مجموعة مسند راحة اليد ولوحة المفاتيح. تركيب لوحة اللمس المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع المكون ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1قم بمحاذاة لوحة اللمس ووضعها داخل الفتحة الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح.
الخطوات التالية .1 .2 .3 .4 قم بتركيب مكبرات الصوت. قم بتركيب البطارية. قم بتركيب غطاء القاعدة. اتبع الإجراءات الواردة في بعد العمل داخل جهاز الكمبيوتر الخاص بك. مجموعة الشاشة إزالة مجموعة الشاشة المتطلبات .1 .2 .3 .4 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. إزالة بطاقة .WLAN عن المهمة يوضح الشكل موقع مجموعة الشاشة ويقدم تمثيلاً مرئيًا لإجراء الإزالة.
الخطوات .1حدد موقع كابل الشاشة ومفصلات الشاشة في جهاز الكمبيوتر. .2قم بإزالة الشريط المثبت لكابل الشاشة في لوحة النظام. .3قم بفتح المزلاج وافصل كابل الشاشة عن لوحة النظام. .4قم بإزالة المسامير اللولبية الثلاثة ) (M2.5x5المثبتة لمفصلة الشاشة اليسرى في لوحة النظام. .5قم بإزالة المسامير اللولبية الثلاثة ) (M2.5x5المثبتة لمفصلة الشاشة اليمنى في لوحة النظام. .6افتح مفصلات الشاشة بزاوية مقدارها 90درجة. .
تركيب مجموعة الشاشة المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع المكون ويقدم تمثيلاً مرئيًا لإجراء التركيب.
الخطوات .1قم بوضع مجموعة الشاشة على سطح مست ٍو ونظيف. .2قم بمحاذاة مجموعة مسند راحة اليد ولوحة المفاتيح ووضعها بمجموعة الشاشة. .3باستخدام أعمدة المحاذاة ،أغلق مفصلات الشاشة. .4أعد وضع المسامير اللولبية الثلاثة ) (M2.5x5المثبتة لمفصلة الشاشة اليسرى في لوحة النظام. .5أعد وضع المسامير اللولبية الثلاثة ) (M2.5x5المثبتة لمفصلة الشاشة اليمنى في لوحة النظام. .6قم بتوصيل كابل الشاشة بالموصول الموجود في لوحة النظام وضع الشريط بلوحة النظام. الخطوات التالية .
إطار الشاشة إزالة إطار الشاشة المتطلبات .1 .2 .3 .4 .5 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. إزالة بطاقة .WLAN قم بإزالة مجموعة الشاشة. عن المهمة يوضح الشكل موقع إطار الشاشة ويقدم تمثيلاً مرئيًا لإجراء الإزالة. الخطوات .1ارفع حواف إطار الشاشة بعناية خارج مجموعة الغطاء الخلفي للشاشة والهوائي. .2ارفع إطار الشاشة خارج مجموعة الغطاء الخلفي للشاشة والهوائي.
تركيب إطار الشاشة المتطلبات اذا كنت بصدد استبدال أحد المكونات ،فقم بإزالة المكون الموجود قبل تنفيذ إجراء التركيب. عن المهمة يوضح الشكل موقع إطار الشاشة ويقدم تمثيلاً مرئيًا لإجراء الإزالة. الخطوات قم بمحاذاة إطار الشاشة مع الغطاء الخلفي للشاشة ومجموعة الهوائي وقم بتثبيت إطار الشاشة في مكانه بعناية. الخطوات التالية .1 .2 .3 .4 .5 54 قم بتركيب مجموعة الشاشة. قم بتركيب بطاقة .WLAN قم بتركيب البطارية. قم بتركيب غطاء القاعدة.
لوحة النظام إزالة لوحة النظام المتطلبات .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. قم بإزالة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع .M.2 2280 قم بإزالة محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع .M.2 2230 إزالة بطاقة .WLAN قم بإزالة مروحة وحدة المعالجة المركزية.
56 إزالة المكونات وتركيبها
إزالة المكونات وتركيبها 57
الخطوات .1افتح المزلاج وافصل كابل لوحة ) I/Oالإدخال/الإخراج( عن لوحة النظام. .2افصل كابل مهايئ التيار عن لوحة النظام. .3افصل كابل مكبر الصوت من لوحة النظام. .4افتح المزلاج وافصل كابل لوحة اللمس عن لوحة النظام. .5افتح المزلاج وافصل كابل الإضاءة الخلفية للوحة المفاتيح عن لوحة النظام. .6قم بإزالة شريط مايلار الموجود في موصل لوحة المفاتيح. .7افتح المزلاج وافصل كابل لوحة المفاتيح عن لوحة النظام. .8قم بإزالة الشريط المثبت لكابل الشاشة في لوحة النظام.
إزالة المكونات وتركيبها 59
60 إزالة المكونات وتركيبها
الخطوات .1قم بإزاحة المنافذ الموجودة في لوحة النظام إلى داخل الفتحات الموجودة في مجموعة مسند راحة اليد ولوحة المفاتيح ،ثم قم بمحاذاة فتحات المسامير اللولبية الموجودة في لوحة النظام مع فتحات المسامير اللولبية الموجودة في مجموعة مسند راحة اليد لوحة المفاتيح. .2أعد وضع المسامير اللولبية الستة ) (M2x4المثبتة لغطاء للوحة النظام في مجموعة مسند راحة اليد ولوحة المفاتيح. .3قم بتوصيل كابل الشاشة بالموصل الموجود في لوحة النظام. .
دعامة لوحة المفاتيح إزالة حامل لوحة المفاتيح المتطلبات .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 اتبع الإجراءات الواردة في قبل العمل داخل جهاز الكمبيوتر الخاص بك. قم بإزالة غطاء القاعدة. قم بإزالة البطارية. إزالة بطاقة .WLAN قم بإزالة مروحة وحدة معالجة الرسومات. قم بإزالة مروحة وحدة المعالجة المركزية. قم بإزالة مجموعة الشاشة. قم بإزالة لوحة الإدخال/الإخراج. قم بإزالة زر التشغيل مع قارئ بصمات الأصابع.
عن المهمة يوضح الشكل موقع حامل لوحة المفاتيح ويقدم تمثيلاً مرئيًا لإجراء التركيب. الخطوات .1قم بمحاذاة فتحات المسامير اللولبية الموجودة في حامل لوحة المفاتيح مع فتحات المسامير اللولبية الموجودة في مجموعة لوحة المفاتيح ومسند راحة اليد. .2قم بإزالة المسامير اللولبية ) (M1.2x2التسعة والثلاثين المثبتة لحامل لوحة المفاتيح في مجموعة لوحة المفاتيح ومسند راحة اليد. الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 قم بتركيب لوحة النظام.
.6 .7 .8 .9 .10 .11 .12 قم بإزالة مروحة وحدة معالجة الرسومات. قم بإزالة مروحة وحدة المعالجة المركزية. قم بإزالة مجموعة الشاشة. قم بإزالة لوحة الإدخال/الإخراج. قم بإزالة زر التشغيل مع قارئ بصمات الأصابع. قم بإزالة منفذ مهايئ التيار. قم بإزالة لوحة النظام. ملاحظة يمكن إزالة لوحة النظام مع المشتت الحراري. .13قم بإزالة حامل لوحة المفاتيح. عن المهمة يوضح الشكل موقع لوحة المفاتيح ويقدم تمثيلاً مرئيًا لإجراء الإزالة.
الخطوات قم بمحاذاة لوحة المفاتيح بمجموعة مسند راحة اليد. الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 قم بتركيب حامل لوحة المفاتيح. قم بتركيب لوحة النظام. قم بتركيب منفذ مهايئ التيار. قم بتركيب زر التشغيل مع قارئ بصمات الأصابع. قم بتركيب لوحة الإدخال/الإخراج. قم بتركيب مجموعة الشاشة. قم بتركيب مروحة وحدة المعالجة المركزية. قم بتركيب مروحة وحدة معالجة الرسومات. قم بتركيب محرك الأقراص الثابتة.
.7 .8 .9 .10 .11 .12 .13 .14 قم بإزالة مروحة وحدة المعالجة المركزية. قم بإزالة مكبرات الصوت. قم بإزالة مجموعة الشاشة. قم بإزالة لوحة الإدخال/الإخراج. قم بإزالة زر التشغيل مع قارئ بصمات الأصابع. قم بإزالة منفذ مهايئ التيار. قم بإزالة لوحة اللمس قم بإزالة لوحة النظام. ملاحظة يمكن إزالة لوحة النظام مع المشتت الحراري. .15قم بإزالة حامل لوحة المفاتيح. .16قم بإزالة لوحة المفاتيح.
الخطوات ضع مسند راحة اليد على سطح مست ٍو. الخطوات التالية .1 .2 .3 .4 .5 .6 .7 .8 .9 .10 .11 .12 .13 .14 .15 .16 قم بتركيب لوحة المفاتيح. قم بتركيب حامل لوحة المفاتيح. قم بتركيب لوحة النظام. قم بتركيب لوحة اللمس. قم بتركيب منفذ مهايئ التيار. قم بتركيب زر التشغيل مع قارئ بصمات الأصابع. قم بتركيب لوحة الإدخال/الإخراج. قم بتركيب مجموعة الشاشة. قم بتركيب مكبرات الصوت.
3 برامج تشغيل الجهاز أداة تثبيت برامج مجموعة شرائح Intel في مدير الأجهزة ،تحقق من تثبيت برنامج تشغيل مجموعة الشرائح. قم بتثبيت تحديثات مجموعة شرائح Intelمن الموقع .www.dell.com/support برامج تشغيل الفيديو في مدير الأجهزة ،تحقق من تثبيت برنامج تشغيل الفيديو. قم بتثبيت تحديث برنامج تشغيل الفيديو من الموقع .www.dell.com/support برنامج تشغيل Intel Serial IO في مدير الأجهزة ،تحقق من تثبيت برنامج تشغيل وحدة ) I/Oالإدخال/الإخراج( التسلسلية من .
4 إعداد النظام ملاحظة بنا ًء على جهاز الكمبيوتر والأجهزة الخاصة به التي تم تركيبها ،قد تظهر العناصر المدرجة في هذا القسم أو قد لا يتم عرضها. إعداد النظام تنبيه ما لم تكن مستخد ًما متمكنًا للكمبيوتر ،فلا تغير الإعدادات الموجودة في برنامج إعداد .BIOSإذ قد تجعل بعض التغييرات الكمبيوتر يعمل بشكل غير صحيح. ملاحظة قبل تغيير برنامج إعداد ،BIOSيوصى بتدوين معلومات شاشة برنامج إعداد ا BIOSكمرجع في المستقبل.
• • محرك الأقراص القابلة للإزالة )في حالة توفره( محرك الأقراص STXXXX ملاحظة يشير XXXإلى رقم محرك أقراص .SATA • • • محرك أقراص ضوئية )في حالة توفره( محرك أقراص ثابتة ) SATAفي حالة توفره( التشخيصات ملاحظة عند اختيار تشخيصات ستظهر شاشة تشخيصات .ePSA يعرض أيضًا تسلسل التمهيد الخيار الخاص بالوصول إلى شاشة ضبط النظام. خيارات إعداد النظام ملاحظة بنا ًء على جهاز الكمبيوتر هذا والأجهزة الخاصة به التي تم تركيبها ،قد تظهر العناصر المدرجة في هذا القسم أو قد لا تظهر.
معلومات النظام العامة معلومات الجهاز M.2 SATA يعرض معلومات جهاز محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 SATAلجهاز الكمبيوتر. M.2 PCIe SSD-0 يعرض معلومات محرك الأقراص المزود بذاكرة مصنوعة من مكونات صلبة من نوع M.2 PCIeلجهاز الكمبيوتر. Video Controller يعرض نوع وحدة التحكم في الفيديو لجهاز الكمبيوتر. dGPU Video Controller يعرض معلومات بطاقات الرسومات المنفصلة لجهاز الكمبيوتر.
جدول .4خيارات إعداد النظام—قائمة الفيديو الفيديو LCD Brightness يضبط سطوع اللوحة بشكل منفصل للبطارية وطاقة التيار المتردد. جدول .5خيارات إعداد النظام—قائمة الأمان الأمان Admin Password يُعين كلمة مرور المسؤول أو يُغيرها أو يحذفها. System Password يُعين كلمة مرور النظام أو يُغيرها أو يحذفها. Strong Password يقوم بتمكين أو تعطيل كلمات المرور القوية.
ملحقات حماية برامج Intel Intel TurboBoost يقوم بتمكين أو تعطيل وضع Intel TurboBoostللمعالج. الحالة الافتراضية :ممكن. HyperThread control يقوم بتمكين أو تعطيل تقنية خيوط المعالجة الفائقة ) (HyperThreadingفي المعالج. الحالة الافتراضية :ممكن. إدارة الطاقة AC Behavior يقوم بتمكين تشغيل النظام بشكل تلقائي عند توصيل تيار متردد. Enable Intel Speed Shift Technology يقوم بتمكين تقنية ) Speed Shiftتبديل السرعة( من Intelأو تعطيلها.
جدول .10خيارات إعداد النظام—قائمة الصيانة الصيانة Service Tag يعرض رمز خدمة النظام. Asset Tag ينشئ رمز أصل النظام. BIOS Downgrade يتحكم في إعادة البرنامج الثابت للنظام إلى المراجعات السابقة. BIOS Recovery يمكن المستخدم من إجراء الاسترداد من بعض حالات BIOSالتالفة من خلال ملف استرداد على محرك الأقراص الثابتة الرئيسي للمستخدم أو مفتاح USBخارجي. جدول .11خيارات إعداد النظام—قائمة سجلات النظام سجلات النظام BIOS Events يعرض أحداث .
5 استشكاف الأخطاء وإصلاحها تشخيصات التقييم المحسن للنظام قبل التمهيد )(ePSA عن المهمة تقوم تشخيصات ) ePSAالمعروفة أيضًا بتشخيصات النظام( بفحص كامل لجهازك .يتم تضمين ePSAبنظام الإدخال والإخراج الأساسي ) (BIOSويتم تشغيلها داخليًا بواسطة نظام الإدخال والإخراج الأساسي ) .
جدول .
تعطيل ذاكرة بتقنية Optaneمن Intel عن المهمة تنبيه بعد تعطيل ذاكرة ،Intel Optaneلا تقم بإلغاء تثبيت برنامج التشغيل الخاص بتقنية التخزين Intel Rapidلأنه يؤدي إلى خطأ الشاشة الزرقاء .يمكن إزالة واجهة المستخدم لتقنية التخزين السريع من Intelبدون إلغاء تثبيت برنامج التشغيل. ملاحظة يلزم تعطيل ذاكرة Intel Optaneقبل إزالة جهاز التخزين SATAالذي يتم تسريعه من خلال وحدة ذاكرة Intel Optaneمن الكمبيوتر. الخطوات .1على شريط المهام ،انقر فوق مربع البحث ،ثم اكتب .
نقرا مزدو ًجا فوق رمز ملف تحديث نظام BIOSواتبع الإرشادات التي تظهر على الشاشة. .9انقر ً التخلص من الطاقة الزائدة عن المهمة الطاقة الزائدة هي كهرباء إستاتيكية زائدة يستمر وجودها على الكمبيوتر حتى بعد إيقاف تشغيله وإزالة البطارية .يوفر الإجراء التالي تعليمات حول كيفية التخلص من الطاقة الزائدة: الخطوات .1قم بإيقاف تشغيل جهاز الكمبيوتر الخاص بك. .2قم بإزالة غطاء القاعدة. .3قم بإزالة البطارية. .
6 الحصول على المساعدة والاتصال بشركة Dell موارد المساعدة الذاتية يمكنك الحصول على المعلومات والمساعدة بشأن منتجات Dellوخدماتها باستخدام مصادر المساعدة الذاتية هذه: جدول .14موارد المساعدة الذاتية موارد المساعدة الذاتية موقع الموارد معلومات حول منتجات وخدمات Dell www.dell.com My Dell تلميحات الاتصال بالدعم في حقل البحث بنظام التشغيل ،Windowsاكتب ،Contact Supportواضغط على الزر .Enter المساعدة عبر الإنترنت لنظام التشغيل www.dell.