Inspiron 7591 Servicehåndbok Forskriftsmessig modell: P83F Forskriftmessig type: P83F001
Merknader, forholdsregler og advarsler MERK En merknad inneholder viktig informasjon som hjelper deg med å bruke ditt produkt mer effektivt. FORSIKTIG Angir enten potensiell fare for maskinvaren eller tap av data, og forteller hvordan du kan unngå problemet. ADVARSEL ADVARSEL angir potensiell fare for skade på eiendom, personskade eller død. © 2019 Dell Inc. eller dets datterselskaper. Med enerett. Dell og EMC og andre varemerker er varemerker for Dell Inc. eller dets datterselskaper.
Innholdsfortegnelse 1 Sikkerhetsanvisninger...................................................................................................................6 Før du foretar arbeid inne i datamaskinen.......................................................................................................................... 6 Før du begynner...............................................................................................................................................................
Sette inn CPU-viften..................................................................................................................................................... 31 Varmeavleder....................................................................................................................................................................... 32 Ta ut varmeavlederen – UMA..................................................................................................................................
Clearing BIOS (System Setup) and System passwords (Slette BIOS (Systemkonfigurasjon) og systempassord)............................................................................................................................................................... 67 5 Feilsøking.................................................................................................................................. 68 Enhanced Pre-Boot System Assessment (ePSA)-diagnostikk...............................................
1 Sikkerhetsanvisninger Følg disse retningslinjene for sikkerhet for å beskytte datamaskinen mot mulig skade og verne om din egen sikkerhet. Hvis ikke annet er angitt, forutsetter hver av prosedyrene i dette dokumentet følgende: • • Du har lest sikkerhetsanvisningene som fulgte med datamaskinen. En komponent kan byttes ut eller, hvis enheten er kjøpt separat, settes inn ved å utføre fremgangsmåten for å ta ut komponenten i motsatt rekkefølge.
MERK Hvis du bruker et annet operativsystem, må du se dokumentasjonen til operativsystemet for å finne instruksjoner for hvordan du avslutter og slår av. 3. Koble datamaskinen og alt tilkoblet utstyr fra strømuttakene. 4. Koble fra alle tilkoblede nettverksenheter og perifert utstyr som tastatur, mus og skjerm fra datamaskinen. 5. Fjern eventuelle minnekort og optiske plater fra datamaskinen.
• • • • plugger du håndleddstroppens jordingsledning inn i testeren mens stroppen er festet rundt håndleddet og trykker på knappen for å teste. En grønn LED-lampe lyser hvis testen er vellykket og en rød LED-lampe lyser og det høres en alarm hvis testen er mislykket. Isolatorelementer – det er svært viktig å holde ESD-sensitive enheter, for eksempel varmeavlederens plastinnfatning borte fra de interne delene som er isolatorer og ofte svært strømførende.
2 Ta ut og installere komponenter Anbefalte verktøy Veiledningene i dette dokumentet kan kreve at du bruker følgende verktøy: • • • Philips skrutrekker #1 Senkskrujern Plastspiss Skrueliste MERK Det anbefales å notere skruetype, antall skruer og deretter plassere dem i en oppbevaringsboks for skruer når du fjerner skruer fra en komponent. Dette er for å sikre at du bruker riktig antall skruer og riktig skruetype når komponenten settes inn. MERK Enkelte datamaskiner har magnetiske overflater.
Komponent Festes til Type skrue Antall Strømadapterport Håndleddstøtte og tastaturenhet M1,2x2 1 Strømknapp og valgfri fingeravtrykkleser Håndleddstøtte og tastaturenhet M1,6x2 2 GPU-vifte Håndleddstøtte og tastaturenhet M2x4 2 M.2 2280 SSD-disk Hovedkort M2x4 2 M.
1. Fest (M2x5)-skruene som fester bunndekselet til håndleddstøtten og tastaturenheten. 2. Løsne festeskruene som fester bunndekselet til håndleddstøtten og tastaturenheten. 3. Lirk for å åpne bunndekselet ved å starte fra øverst i midten av kanten til håndleddstøtten og tastaturenheten, og følg "veiledningslinjen" som er angitt på bildet for å ta ut bunndekselet. 4. Løft bunndekselet fra håndleddstøtten og tastaturenheten.
Sette på bunndekselet Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av bunndekselet, og gir en visuell fremstilling av installasjonsfremgangsmåten. 1. Sett bunndekselet på håndleddstøtten og tastaturenheten, og klikk bunndekselet på plass. 2. Stram festeskruene som fester bunndekselet til håndleddstøtten og tastaturenheten. 3. Fest (M2x5)-skruene som fester bunndekselet til håndleddstøtten og tastaturenheten.
• Sørg for at du ikke mister eller forlegger skruene ved service av dette produktet for å forhindre utilsiktet punktering eller skade på batteriet og andre systemkomponenter. • Hvis batteriet sitter fast i datamaskinen som et resultat av oppsvulming, må du ikke prøve å løsne batteriet, da punktering, bøying, eller knusing av et litium-ion-batteri kan være farlig. Kontakt Dells tekniske kundestøtte for hjelp ved et slikt tilfelle. Gå til www.dell.com/contactdell. • Kjøp alltid genuine batterier fra www.
1. Sett batteriet på håndleddstøtten og tastaturenheten, og juster skruehullene på batteriet etter skruehullene på håndleddstøtten og tastaturenheten. 2. Fest (M2x4)-skruene som fester batteriet til hovedkortet, håndleddstøtten og tastaturenheten. 3. Koble batterikabelen til hovedkortet. 1. Sett på bunndekselet. 2. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Ta ut 6-cellers batteri MERK Batteriet i datamaskinen varierer avhengig av konfigurasjonen som er bestilt. 1.
1. Koble batterikabelen fra hovedkortet. 2. Fjern (M2x4)-skruene som fester batteriet til håndleddstøtten og tastaturenheten. 3. Løft batteriet fra håndleddstøtten og tastaturenheten. Sette inn 6-cellers batteri Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av batteriet, og gir en visuell fremstilling av fremgangsmåten for å sette det inn.
1. Sett batteriet på håndleddstøtten og tastaturenheten, og juster skruehullene på batteriet etter skruehullene på håndleddstøtten og tastaturenheten. 2. Fest (M2x4)-skruene som fester batteriet til hovedkortet, håndleddstøtten og tastaturenheten. 3. Koble batterikabelen til hovedkortet. 1. Sett på bunndekselet. 2. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Minnemoduler Ta ut minnemodulene 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet. 3.
1. Løft Mylar-tapen, og atskill festeklemmene i hver ende av minnemodulsporet ved hjelp av fingertuppene til minnemodulen spretter opp. 2. Skyv og ta ut minnemodulen fra minnemodulsporet på hovedkortet. Sette inn minnemodulene Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av minnemodulen, og gir en visuell fremstilling av fremgangsmåten for å sette den inn. 1.
3. Trykk minnebrikken ned helty til den låse spå plass med et klikk. MERK Hvis du ikke hører et klikk, må du ta ut minikortet og sette det inn på nytt. 1. Koble til batterikabelen 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. WLAN-kort Ta ut WLAN-kortet 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet. 3. Ta ut batteriet.
1. Juster hakket på WLAN-kortet etter tappen på WLAN-kortsporet, og sett WLAN-kortet i vinkel inn i WLAN-kortsporet. 2. Koble antennekablene til WLAN-kortet. 3. Juster og sett WLAN-kortbraketten på WLAN-kortet. 4. Fest (M2x4)-skruen som fester WLAN-kortbraketten til WLAN-kortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. SSD-stasjon Ta ut M.2 2280 SSD-disken 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2.
1. Fjern (M2x4)-skruene som fester SSD-diskmodulvernet til håndleddstøtten og tastaturenheten. 2. Skyv og ta ut SSD-diskmodulvernet fra SSD-disksporet. 3. Skyv og ta ut SSD-diskmodulen fra SSD-disksporet. Sette inn M.2 2280 SSD-disken Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av SSD-diskbraketten, og gir en visuell fremstilling av fremgangsmåten for å justere braketten slik at den passer til M.
Figuren viser plasseringen av harddisken, og gir en visuell fremstilling av fremgangsmåten for å sette den inn. 1. Juster SSD-diskbraketten slik at den passer til M.2 2280 SSD-disken hvis dette er nødvendig. 2. Juster hakket på SSD-diskmodulen etter tappen på SSD-disksporet. 3. Skyv SSD-diskmodulen bestemt i vinkel inn i SSD-disksporet. 4. Sikre tappen på SSD-disksporet til sporet på SSD-diskbraketten. 5. Fest (M2x4)-skruene som fester SSD-diskmodulvernet til håndleddstøtten og tastaturenheten. 1.
1. Fjern (M2x4)-skruen som fester SSD-disken til håndleddstøtten og tastaturenheten. 2. Skyv og ta ut M.2 SSD-diskmodulen fra M.2 SSD-disksporet på hovedkortet. Sett inn M.2 2230 SSD-disken Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av SSD-diskbraketten, og gir en visuell fremstilling av fremgangsmåten for å justere braketten slik at den passer til M.2 2230 SSD-disken. Figuren viser plasseringen av M.
1. Hvis det er nødvendig, justerer du SSD-diskbraketten slik at den passer til M.2 2230 SSD-disken. 2. Juster hakket på SSD-diskmodulen etter tappen på SSD-disksporet. 3. Skyv SSD-diskmodulen bestemt i vinkel inn i SSD-disksporet. 4. Fest (M2x4)-skruen som fester SSD-diskmodulen til håndleddstøtten og tastaturenheten. 1. Koble til batterikabelen 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Ta ut M.2 2280 PCIe SSD-disken 1.
1. Fjern (M2x2.5)-skruen som fester SSD-disken til hovedkortet. 2. Skyv og ta ut M.2 SSD-diskmodulen fra M.2 SSD-disksporet på hovedkortet. Sette inn M.2 2280 PCIe SSD-disken Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av M.2 2280 SSD-disken, og gir en visuell fremstilling av fremgangsmåten for å sette den inn: 1. Juster hakket på SSD-diskmodulen etter tappen på SSD-disksporet. 2.
1. Koble til batterikabelen 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Harddisk Ta ut harddisken 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet. 3. Koble fra batterikabelen. Figuren viser plasseringen av harddisken, og gir en visuell fremstilling av fremgangsmåten for å ta den ut. MERK Harddisken er kun tilgjengelig på datamaskiner som leveres med 3-cellers batteri.
1. Åpne låsen, og koble styreplatekabelen fra hovedkortet. 2. Fjern (M2x4)-skruene som fester harddiskbraketten til håndleddstøtten og tastaturenheten. 3. Løft harddiskenheten sammen med kabelen fra håndleddstøtten og tastaturenheten. 4. Koble mellomstykket fra harddiskenheten. 5. Fjern de fire skruene (M3x3) som fester harddiskbraketten til harddisken. 6. Løft harddisken fra harddiskbraketten.
1. Sett harddisken inn i harddiskbraketten. 2. Juster skruehullene på harddiskbraketten etter skruehullene på harddisken, og fest (M3x3)-skruene som fester harddiskbraketten til harddisken. 3. Koble mellomstykket til harddiskenheten. 4. Juster skruehullene på harddiskenheten etter skruehullene på håndleddstøtten og tastaturenheten. 5. Fest (M2x4)-skruene som fester harddiskenheten til håndleddstøtten og tastaturenheten. 6. Koble harddiskkabelen til hovedkortet. 1. Koble til batterikabelen 2.
1. Koble høyttalerkabelen fra hovedkortet. 2. Legg merke til føringen av høyttalerkabelen, og ta ut høyttalerkabelen fra kabelføringene på håndleddstøtten og tastaturenheten. MERK Legg merke til plasseringen av gummiringene før du løfter høyttalerne. 3. Løft høyttalerne sammen med kabelen fra håndleddstøtten og tastaturenheten. Montere høyttalerne Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten.
1. Sett høyttalerne i sporene på håndleddstøtten og tastaturenheten ved hjelp av justeringsstolpene og gummistroppene. 2. Før høyttalerkabelen gjennom kabelføringene på håndleddsstøtten og tastaturenheten. 3. Koble høyttalerkabelen til hovedkortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Vifte for grafikkbehandlingsenhet (GPU-enhet) Ta ut GPU-viften 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet.
1. Fjern (M2x4)-skruene som fester GPU-viften til håndleddstøtten og tastaturenheten. 2. Koble GPU-viftekabelen fra hovedkortet. 3. Skyv og løft GPU-viften fra håndleddstøtten og tastaturenheten. Sette inn GPU-viften Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av GPU-viften, og gir en visuell fremstilling av fremgangsmåten for å sette den inn. 1.
3. Fest (M2x4)-skruene som fester GPU-viften til håndleddstøtten og tastaturenheten. 4. Koble GPU-viftekabelen til hovedkortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. CPU-vifte Ta ut CPU-viften 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet. 3. Ta ut batteriet. Figuren viser plasseringen av CPU-viften, og gir en visuell fremstilling av fremgangsmåten for å ta den ut. 1.
1. Skyv og sett CPU-viften på håndleddstøtten og tastaturenheten. 2. Juster skruehullene på CPU-viften etter skruehullene på håndleddsstøtten og tastaturenheten. 3. Fest (M2x4)-skruene som fester CPU-viften til håndleddstøtten og tastaturenheten. 4. Koble CPU-viftekabelen til hovedkortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
1. Løsne i rekkefølge (angitt på varmeavlederen) de fire festeskruene som fester varmeavlederen til hovedkortet. 2. Løft og ta ut varmeavlederen fra håndleddstøtten og tastaturenheten. Sette inn varmeavlederen – UMA Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av varmeavlederen, og gir en visuell fremstilling av fremgangsmåten for å sette den inn. 1.
2. 3. 4. 5. Sett inn GPU-viften Sett inn batteriet. Sett på bunndekselet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Ta ut varmeavlederen – atskilt MERK Varmeavlederen i datamaskinen varierer avhengig av konfigurasjonen som er bestilt. 1. 2. 3. 4. 5. Følg prosedyren i Før du arbeider inne i datamaskinen. Ta av bunndekslet. Ta ut batteriet.
1. Sett varmeavlederen på hovedkortet, og juster skruehullene på varmeavlederen etter skruehullene på hovedkortet. 2. Stram i rekkefølge, (angitt på varmeavlederen), de sju festeskruene som fester varmeavlederen til hovedkortet. 1. 2. 3. 4. 5. Sett inn CPU-viften. Sett inn GPU-viften Sett inn batteriet. Sett på bunndekselet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Klokkebatteri Ta ut klokkebatteriet 1. Følg prosedyren i Før du arbeider inne i datamaskinen. 2. Ta av bunndekslet.
1. Koble kabelen til klokkebatteriet fra I/U-kortet. 2. Ta ut knappcellebatteriet fra håndleddstøtten og tastaturenheten. Sette inn knappcellebatteriet Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av knappcellebatteriet, og gir en visuell fremstilling av fremgangsmåten for å sette det inn.
1. Fest knappcellebatteriet til sporet på håndleddstøtten og tastaturenheten. 2. Før kabelen for knappcellebatteriet som vist, og koble den til I/O-kortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. I/U-kort Fjerne I/U-kortet 1. 2. 3. 4. Følg prosedyren i Før du arbeider inne i datamaskinen. Ta av bunndekslet. Ta ut batteriet.
1. Åpne låsen, og koble fra I/U-kortkabelen fra I/U-kortet. 2. Åpne låsen, og koble fingeravtrykkleserkabelen fra I/O-kortet. 3. Koble kabelen til klokkebatteriet fra I/U-kortet. 4. Fjern (M2x3)-skruene som fester I/O-kortet til håndleddstøtten og tastaturenheten. 5. Løft I/O-kortet fra håndleddstøtten og tastaturenheten. Sette inn I/U-kortet Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten.
1. Sett I/O-kortet på håndleddstøtten og tastaturenheten. 2. Juster skruehullene på I/O-kortet etter skruehullene på håndleddstøtten og tastaturenheten. 3. Fest (M2x3)-skruene som fester I/O-kortet til håndleddstøtten og tastaturenheten. 4. Koble klokkebatterikabelen til I/U-kortet. 5. Koble fingeravtrykkleserkabelen til I/O-kortet, og lukk låsen som fester kabelen. 6. Koble I/O-kortkabelen til I/O-kortet, og lukk låsen som fester kabelen. 1. 2. 3. 4. Sett inn GPU-viften Sett inn batteriet.
Av/på-knapp med fingeravtrykksleser (tilleggsutstyr) Ta ut strømknappen og valgfri fingeravtrykkleser 1. 2. 3. 4. 5. 6. Følg prosedyren i Før du arbeider inne i datamaskinen. Ta av bunndekslet. Ta ut batteriet. Ta ut WLAN-kortet. Ta ut GPU-viften Ta ut I/U-kortet. Figuren viser plasseringen av strømknappen med valgfri fingeravtrykkleser, og gir en visuell fremstilling av fremgangsmåten for å ta den ut. 1. Fjern (M1.
1. Sett inn strømknappen med valgfri fingeravtrykkleser på håndleddstøtten og tastaturenheten ved hjelp av justeringsstolpen. 2. Fest (M1.2x2)-skruene som fester strømknappen med valgfri fingeravtrykkleser til håndleddstøtten og tastaturenheten. 1. 2. 3. 4. 5. 6. Sett inn I/O-kortet. Sett inn GPU-viften Sett inn WLAN-kortet. Sett inn batteriet. Sett på bunndekselet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Strømadapterport Ta ut strømadapterporten 1.
1. Fjern (M2.5x5)-skruene som fester venstre skjermhengsel til håndleddstøtten og tastaturenheten. 2. Åpne skjermhengslene i en vinkel på 90 grader. 3. Fjern (M2x4)-skruen som fester strømadapterporten til håndleddstøtten og tastaturenheten. 4. Koble kabelen til strømadapterporten fra hovedkortet. 5. Løft strømadapterporten sammen med kabelen fra håndleddsstøtten og tastaturenheten.
1. Koble kabelen til strømadapterporten til hovedkortet. 2. Fest (M2x4)-skruen som fester strømadapterporten til håndleddstøtten og tastaturenheten. 3. Lukk skjermhengslene ved hjelp av justeringsstolpene. 4. Fest (M2.5x5)-skruene som fester venstre skjermhengsel til hovedkortet. 1. Sett inn batteriet. 2. Sett på bunndekselet. 3. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Pekeflate Fjerne styreplaten 1. 2. 3. 4. Følg prosedyren i Før du arbeider inne i datamaskinen.
1. Fjern (M2x3)-skruene som fester styreplatebraketten til håndleddstøtten og tastaturenheten. 2. Løft styreplatebraketten fra håndleddstøtten og tastaturenheten. 3. Åpne låsen, og koble styreplatekabelen fra hovedkortet. 4. Fest (M1.6x2)-skruene som fester styreplaten til håndleddstøtten og tastaturenheten. 5. Løft styreplaten sammen med kabelen fra håndleddstøtten og tastaturenheten.
1. Juster og sett styreplaten inn i sporet på håndleddstøtten og tastaturenheten. 2. Fest (M1.6x2)-skruene som fester styreplaten til håndleddstøtten og tastaturenheten. 3. Skyv styreplatekabelen til kontakten på hovedkortet, og lukk låsen som fester kabelen. 4. Juster og sett styreplatebraketten inn i sporet på håndleddstøtten og tastaturenheten [1]. 5. Fjern (M2x3)-skruene som fester styreplatebraketten til håndleddstøtten og tastaturenheten. 1. 2. 3. 4. Sett inn høyttalerne Sett inn batteriet.
Figuren viser plasseringen av skjermenheten, og gir en visuell fremstilling av fremgangsmåten for å ta den ut.
1. Finn skjermkabelen og skjermhengslene på datamaskinen. 2. Fjern teipen som fester skjermkabelen til hovedkortet. 3. Åpne låsen, og koble tastaturkabelen fra hovedkortet. 4. Fjern (M2x5.5)-skruene som fester venstre skjermhengsel til hovedkortet. 5. Fjern (M2.5x5)-skruene som fester høyre skjermhengsel til hovedkortet. 6. Åpne skjermhengslene i en vinkel på 90 grader. 7. Ta ut håndleddstøtten og tastaturenheten fra skjermenheten.
Montere skjermenheten Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten. Figuren viser plasseringen av komponenten, og gir en visuell fremstilling av fremgangsmåten for å sette den inn.
1. Plasser skjermenheten på en ren og jevn flate. 2. Skyv og sett håndleddstøtten og tastaturenheten på skjermenheten. 3. Lukk skjermhengslene ved hjelp av justeringsstolpene. 4. Fest (M2.5x5)-skruene som fester venstre skjermhengsel til hovedkortet. 5. Fest (M2.5x5)-skruene som fester høyre skjermhengsel til hovedkortet. 6. Koble skjermkabelen til kontakten på hovedkortet, og fest tapen til hovedkortet. 1. 2. 3. 4. Sett inn WLAN-kortet. Sett inn batteriet. Sett på bunndekselet.
5. Ta av skjermenheten. Figuren viser plasseringen av skjermrammen, og gir en visuell fremstilling av fremgangsmåten for å ta den ut. 1. Lirk forsiktig kantene på skjermrammen fra skjermens bakdeksel og antenneenheten. 2. Løft skjermrammen av skjermens bakdeksel og antenneenheten. Montere skjermrammen Hvis du setter inn en komponent, må du ta ut den eksisterende komponenten før du utfører installasjonsfremgangsmåten.
Juster skjermrammen etter det skjermens bakdeksel, og klikk skjermrammen forsiktig på plass. 1. 2. 3. 4. 5. Sett inn skjermenheten. Sett inn WLAN-kortet. Sett inn batteriet. Sett på bunndekselet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Hovedkort Ta ut hovedkortet 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Følg prosedyren i før du arbeider inne i datamaskinen. Ta av bunndekslet. Ta ut batteriet. Ta ut M.2 2280 SSD-disken. Ta ut M.2 2230 SSD-disken. Ta ut WLAN-kortet.
Figuren viser plasseringen av hovedkortet, og gir en visuell fremstilling av fremgangsmåten for å ta det ut.
Ta ut og installere komponenter 53
1. Åpne låsen, og koble fra I/U-kortkabelen fra hovedkortet. 2. Koble strømadapterkabelen fra hovedkortet. 3. Koble høyttalerkabelen fra hovedkortet. 4. Åpne låsen, og koble styreplatekabelen fra hovedkortet. 5. Åpne låsen, og koble kabelen til tastaturets bakgrunnsbelysning fra hovedkortet. 6. Fjern mylar på tastatur kontakten. 7. Løft opp låsen, og koble tastaturkabelen fra hovedkortet. 8. Fjern teipen som fester skjermkabelen til hovedkortet. 9. Åpne låsen, og koble tastaturkabelen fra hovedkortet. 10.
Ta ut og installere komponenter 55
Ta ut og installere komponenter
1. Skyv portene på hovedkortet inn i sporene på håndleddstøtten og tastaturenheten, og juster skruehullene på hovedkortet etter skruehullene på håndleddstøtten og tastaturenheten. 2. Fest (M2x4)-skruene som fester hovedkortet til håndleddstøtten og tastaturenheten. 3. Koble skjermkabelen til kontakten på hovedkortet. 4. Fest teipen som fester skjermkabelen til hovedkortet. 5. Fest (M2x5)-skruene som fester USB Type-C-portbraketten til hovedkortet. 6.
Palm-rest and keyboard assembly (Håndleddstøtte og tastaturenhet) Ta ut håndleddstøtten og tastaturenheten 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Følg prosedyren i Før du arbeider inne i datamaskinen. Ta av bunndekslet. Ta ut batteriet. Ta ut WLAN-kortet. Ta ut harddisken. Ta ut GPU-viften. Ta ut CPU-viften Ta av høyttalerne. Ta av skjermenheten. Ta ut I/O-kortet. Ta ut strømknappen med fingeravtrykkleseren Ta ut strømadapterporten. Ta ut styreplaten Ta ut hovedkortet.
Sett håndleddstøtten og tastaturenheten på et jevnt underlag. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Sett inn hovedkortet. Sett inn styreplaten. Sett inn strømadapterporten. Sett inn strømknappen med fingeravtrykkleseren. Sett inn I/O-kortet. Sett inn skjermenheten. Sett inn høyttalerne Sett inn CPU-viften. Sett inn GPU-viften Sett inn harddisken. Sett inn WLAN-kortet. Sett inn batteriet. Sett på bunndekselet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
3 Enhetsdrivere Intel-brikkesett for installering av programvare I Enhetsbehandling skal du kontrollere om brikkesettdriveren er installert. Installer Intel-brikkesettoppdateringer fra www.dell.com/support. Videodrivere I Enhetsbehandling skal du kontrollere om videodriveren er installert. Installere videodriveroppdateringen fra www.dell.com/support. Intel seriell I/U-driver I Enhetsbehandling skal du kontrollere om Intel seriell I/U-driveren er installert. Installer driveroppdateringene fra www.dell.
4 Systemoppsett MERK Avhengig av datamaskinen og enhetene som er installert, er det mulig at noen av elementene i dette avsnittet ikke vises. Systemoppsett FORSIKTIG Hvis du ikke er en erfaren datamaskinbruker, må du ikke endre innstillingene i konfigurasjonsprogrammet for BIOS. Enkelte endringer kan føre til at datamaskinen slutter å fungere som den skal.
Boot Sequence (Oppstartsrekkefølge) Boot Sequence (Oppstartsrekkefølge) gjør at du kan hoppe over oppstartsrekkefølgen som er definert i systemoppsettet, og starte opp direkte på en bestemt enhet (for eksempel optisk stasjon eller harddisk).
Generell systeminformasjon Gjeldende klokkehastighet Viser gjeldende klokkehastighet for prosessoren. Minimum klokkehastighet Viser minimum klokkerhastighet for prosessoren Maksimal klokkehastighet Viser maksimal klokkehastighet for prosessoren L2-hurtigbuffer for prosessoren Viser størrelsen for prosessorens L2-hurtigbuffer. L3-hurtigbuffer for prosessoren Viser størrelsen for prosessorens L3-hurtigbuffer. HT-kompatibel Viser om prosessoren er HyperThreading-kompatibel.
Systemkonfigurasjon Lyd Aktiver eller deaktiver den innebygde lydkontrolleren. Tastaturbelysning Brukes til å velge driftsmodus til tastaturbelysningsfunksjonen. Tastaturbaklys med vekselstrøm Når baklyset er aktivert, og hvis du trykker på Fn+F10-tastene for å deaktivere belysningen, forblir baklyset av, uavhengig av strømtilstand. Diverse enheter Aktiver eller deaktiver ulike innebygde enheter. Aktiver kamera Aktiverer eller deaktiver kameraet. Tabell 4.
Utvidelser av beskyttelsestiltak for Intel-programvare Støtte for flere kjerner Aktiver flere kjerner. Standard: Aktivert. Intel SpeedStep Aktiver eller deaktiver Intel Speedstep-teknologi. Standard: Aktivert. MERK Hvis dette er aktivert, justeres prosessorens klokkehastighet og kjernespenning dynamisk basert på prosessorbelastningen. C-tilstandkontroll Aktiver eller deaktiver ekstra dvaletilstander for prosessoren. Standard: Aktivert.
Tabell 8. Alternativer for systemkonfigurasjon – meny for virtualiseringsstøtte Støtte for virtualisering Virtualisering Angir om en virtuell maskinmonitor (VMM) kan bruke de ekstra maskinvaremulighetene som følger med Intel virtualiseringsteknologi. VT for direkte I/O Spesifiserer om virtuell maskinmonitor (VMM) kan bruke de ekstra maskinvarefunksjonene som følger med Intel virtualiseringsteknologi for direkte I/O. Tabell 9.
Clearing BIOS (System Setup) and System passwords (Slette BIOS (Systemkonfigurasjon) og systempassord) For å slette system- eller BIOS-passord, må du kontakte Dells tekniske kundestøtte som beskrevet på www.dell.com/contactdell. MERK Hvis du vil ha informasjon om hvordan du tilbakestiller Windows eller programpassord, kan du se vedlagte dokumentasjon for Windows eller programmet.
5 Feilsøking Enhanced Pre-Boot System Assessment (ePSA)diagnostikk ePSA-diagnostikk (også kjent som systemdiagnostikk) utfører en fullstendig kontroll av maskinvaren. ePSA er innebygd BIOS, og startes internt av BIOS.
Følgende tabell viser de forskjellige strøm- og batteri-statuslampemønstre og tilhørende problemer. Tabell 13.
MERK Programmer kan bruke opp til tre etterfølgende omstarter etter aktivering for å oppnå fordelene med full ytelse. Å deaktivere Intel Optane minne FORSIKTIG Etter deaktivering av Intel Optane-minnet må du ikke avinstallere driveren for Intel Rapid-lagringsteknologi da dette vil medføre blåskjermfeil. Brukergrensesnittet for Intel Rapid lagringsteknologien kan fjernes uten å avinstallere driveren.
Utløse reststrøm Reststrøm er gjenværende statisk elektrisitet på datamaskinen også etter at den er slått av og batteriet er tatt ut. Følgende fremgangsmåte gir instruksjoner om hvordan du utløser reststrøm: 1. Slå av datamaskinen. 2. Ta av bunndekslet. 3. Ta ut batteriet. 4. Trykk på og hold nede strømknappen i 15 sekunder for å lade ut reststrøm. 5. Sett inn batteriet. 6. Sett på bunndekselet. 7. Slå på datamaskinen.
6 Få hjelp og kontakte Dell Ressurser for selvhjelp Du kan finne informasjon og få hjelp om Dells produkter og tjenester ved bruk av disse elektroniske selvhjelpsressursene: Tabell 14. Ressurser for selvhjelp Ressurser for selvhjelp Ressurssted Informasjon om Dells produkter og tjenester www.dell.com My Dell Tips Kontakt kundestøtte Skriv Contact Support i Windows-søket, og trykk på Enter. Hjelp på Internett for operativsystem www.dell.com/support/windows www.dell.