Dell™ Inspiron™ 1721 Owner’s Manual Model PP22X w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2007 Dell Inc. All rights reserved.
Contents Finding Information 1 . . . . . . . . . . . . . . . . . . . About Your Computer . . . . . . . . . . . . . . . Determining Your Computer’s Configuration Front View 19 . . . . . . . . . . . . . . . . . . . . . . . . 20 . . . . . . . . . . . . . . . . . . . . . . Right Side View 25 . . . . . . . . . . . . . . . . . . . . . 26 . . . . . . . . . . . . . . . . . . . . . . . . 29 Bottom View 2 19 . . . . . . Left Side View Back View 13 . . . . . . . . . . . . . . . . . . . . . . .
Power Protection Devices . . . . . . . . . . . . . . . 37 Surge Protectors . . . . . . . . . . . . . . . . . . 37 Line Conditioners . . . . . . . . . . . . . . . . . . 38 . . . . . . . . . . 38 Using the Display . . . . . . . . . . . . . . . . . . 39 Adjusting Brightness . . . . . . . . . . . . . . . . . . 39 Uninterruptible Power Supplies 3 Switching the Video Image From Your Computer Display To a Projector . . . . . . . . . . . . . . . . . 39 . . . . 41 . . . . . . . . . . . . . .
Using a Battery . . . . . . . . . . . . . . . . . . . . Battery Performance . . . . . . . . . . . . . . . . . . Checking the Battery Charge . . . . . . . . . . . . . . Dell QuickSet Battery Meter . . . . . . . . . . . . Microsoft® Windows® Battery Meter . Charge Gauge 45 46 46 . . . . . . 47 . . . . . . . . . . . . . . . . . . . 47 Low-Battery Warning . . . . . . . . . . . . . . . 48 Conserving Battery Power . . . . . . . . . . . . . . . 48 Configuring Power Management Settings . . .
Connecting Your Computer to a TV or Audio Device . . . . . . . . . . . . S-Video and Standard Audio . . . . . . . . . . 60 . . . . . . . . . . . . 62 S-Video and S/PDIF Digital Audio . . . . . . . . . Composite Video and Standard Audio . . . . . . . 68 . . . . . . 70 . . . . 72 . . . . . . . 75 . . . . . . . . . . . . . . . . 77 . . . . . . . . . . . . . . . . . . .
Wireless Local Area Network . . . . . . . . . . . . . What You Need to Establish a WLAN Connection . . . . . . . . . . . . . . . . . Checking Your Wireless Network Card . . . . . . Setting Up a New WLAN Using a Wireless Router and a Broadband Modem . . . . . Connecting to a WLAN . 84 84 85 . . . . 86 . . . . . . . . . . . . . . 87 Mobile Broadband (or Wireless Wide Area Network) . . . . . . . . . . . . . . . . . . . . . . What You Need to Establish a Mobile Broadband Network Connection . . .
PC TuneUp . . . . . . . . . . . . . . . . . . . . . 104 . . . . . . . . . . . . . . . . . . . . 104 . . . . . . . . . . . . . . . . . . . . . 105 PC CheckUp Drive Problems Optical drive problems Hard drive problems . . . . . . . . . . . . . . . 105 . . . . . . . . . . . . . . . . 106 . . . . . . . . 107 . . . . . . . . . . . . . . . . . . . . . 108 E-Mail, Modem, and Internet Problems . Error Messages ExpressCard Problems . . . . . . . . . . . . . . . . .
Scanner Problems . Sound and Speaker Problems . . . . . . . . 123 . . . . . . . . . 124 . . . . . . . . . . . . 124 . . . . . . . . . . . . . 124 . . . . . . . . . . . . . . 125 . . . . . . . . . . . . . . . 125 No sound from external speakers No sound from headphones Touch Pad or Mouse Problems Video and Display Problems If the display is blank . 123 . . . . . . . . . . . . . No sound from integrated speakers If the display is difficult to read 126 . . . . . . . . . . . . . . . . .
Optical Drive . . . . . . . . . . . . . . . . . . . . . . . Removing the Optical Drive . . . . . . . . . . . . 141 Replacing the Optical Drive . . . . . . . . . . . . 142 . . . . . . . . . . . . . . . . . . . . . . . 142 Hinge Cover Removing the Hinge Cover . . . . . . . . . . . . . 143 Replacing the Hinge Cover . . . . . . . . . . . . . 143 . . . . . . . . . . . . . . . . . . . . . . . . . 144 Keyboard Removing the Keyboard . . . . . . . . . . . . . . 144 Replacing the Keyboard . .
13 Dell™ QuickSet Features . . . . . . . . . . . 14 Traveling With Your Computer Identifying Your Computer 167 . . . . . . . . . . . . . . . 167 . . . . . . . . . . . . . . . . . 167 . . . . . . . . . . . . . . . . . . . . . . . . 168 Packing the Computer . Travel Tips . . . . . . . 165 Traveling by Air . 15 Getting Help . . . . . . . . . . . . . . . . . . . . . Obtaining Assistance 169 . . . . . . . . . . . . . . . . . . Technical Support and Customer Service DellConnect 168 . . . . .
16 Specifications 17 Appendix . . . . . . . . . . . . . . . . . . . . 177 . . . . . . . . . . . . . . . . . . . . . . . . 185 Using the System Setup Program . . . . . . . . . . . . Viewing the System Setup Screen System Setup Screen . 185 . . . . . . . . . 186 . . . . . . . . . . . . . . . 186 Commonly Used Options . . . . . . . . . . . . . . 186 About Your RAID Configuration . . . . . . . . . . . . . 188 RAID Level 0 Configuration . . . . . . . . . . . . .
Finding Information NOTE: Some features may be optional and may not ship with your computer. Some features may not be available in certain countries. NOTE: Additional information may ship with your computer. What Are You Looking For? Find It Here • • • • Drivers and Utilities Media A diagnostic program for my computer Drivers for my computer Device documentation Notebook System Software (NSS) Documentation and drivers are already installed on your computer.
What Are You Looking For? Find It Here • • • • • • Dell™ Product Information Guide Warranty information Terms and Conditions (U.S.
What Are You Looking For? Find It Here • Service Tag and Express Service Code • Microsoft® Windows® Product Key Service Tag and Microsoft Windows Product Key These labels are located on your computer. • Use the Service Tag to identify your computer when you use support.dell.com or contact support. • Enter the Express Service Code to direct your call when contacting support.
What Are You Looking For? Find It Here • Solutions — Troubleshooting hints and tips, articles from technicians, online courses, and frequently asked questions • Community — Online discussion with other Dell customers • Upgrades — Upgrade information for components, such as the memory, hard drive, and operating system • Customer Care — Contact information, service call and order status, and warranty and repair information • Service and support — Service call status, support history, service contract, and o
What Are You Looking For? Find It Here • Software upgrades and troubleshooting hints — Frequently asked questions, hot topics, and general health of your computing environment Dell Support Utility The Dell Support Utility is an automated upgrade and notification system installed on your computer. This support provides real-time health scans of your computing environment, software updates, and relevant self-support information. Access the Dell Support Utility from the icon on the taskbar.
What Are You Looking For? Find It Here • How to reinstall my operating system Operating System Media The operating system is already installed on your computer. To reinstall your operating system, use one of the following methods: • Microsoft Windows System Restore — Microsoft Windows System Restore returns your computer to an earlier operating state without affecting data files. • Dell PC Restore — Dell PC Restore returns your computer to its original operating state.
About Your Computer Determining Your Computer’s Configuration Based on selections that you made when purchasing your computer, your computer has one of several different video controller configurations. To determine your computer’s video controller configuration: 1 Click Start , and then click Help and Support. 2 Under Pick a Task, click Use Tools to view your computer information and diagnose problems. 3 Under My Computer Information, select Hardware.
Front View 1 2 4 3 14 5 13 12 6 7 11 20 About Your Computer 10 9 8
1 camera indicator (optional) 2 camera (optional) 3 display latch 4 display 5 power button 6 keyboard 7 device status lights 8 touch pad 9 consumer IR 10 media control buttons 11 touch pad buttons 12 Dell™ MediaDirect™ button 13 keyboard status lights 14 digital array microphones CAMERA INDICATOR — Indicates that the camera is turned on. Based on configuration selections you made when ordering your computer, your computer may not include a camera.
DEVICE STATUS LIGHTS The blue lights located to the right of the keyboard indicate the following: Power light – Turns on when you turn on the computer, and blinks when the computer is in a power management mode. Hard drive activity light – Turns on when the computer reads or writes data. NOTICE: To avoid loss of data, never turn off the computer while the light is flashing. Battery status light – Turns on steadily or blinks to indicate battery charge status.
Bluetooth® status light – Turns on when a card with Bluetooth wireless technology is enabled. NOTE: The card with Bluetooth wireless technology is an optional feature. The light turns on only if you ordered the card with your computer. For more information, see the documentation that came with your card. To turn off only the Bluetooth wireless technology functionality, right-click the icon in the notification area, and then click Disable Bluetooth Radio.
D E L L ™ M E D I A D I R E C T ™ B U T T O N — Press the Dell MediaDirect button to launch Dell MediaDirect (see "Using Dell MediaDirect™" on page 59). KEYBOARD STATUS LIGHTS The blue lights located above the keyboard indicate the following: 9 Turns on when the numeric keypad (Num Lock) is enabled. A Turns on when the uppercase letter (Caps Lock) function is enabled. Turns on when the scroll lock function is enabled.
Left Side View 1 2 3 4 1 security cable slot 2 air vents 3 hard drive 4 ExpressCard slot 5 wireless switch 6 Wi-Fi Catcher light 5 6 SECURITY CABLE SLOT — Lets you attach a commercially available antitheft device to the computer (see "Security Cable Lock" on page 93). CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running.
1 2 3 4 1 off position Disables wireless devices. 2 on position Enables wireless devices. 3 momentary position Scans for WLAN networks (see "Dell Wi-Fi Catcher™ Network Locator" on page 92). 4 Wi-Fi Catcher light • • • • • Flashing green: Searching for networks Solid green: Strong network found Solid yellow: Weak network found Flashing yellow: Error Off: No signal found NOTE: The Wi-Fi Catcher Network Locator light appears only when the system is switched off and Wi-Fi is activated in BIOS.
1 battery status light 2 hard drive activity light 3 power light 4 USB connectors (2) 5 network connector (RJ-45) 6 video connector 7 IEEE 1394 connector 8 8-in-1 memory card reader 9 eject button 10 optical drive 11 audio connectors AUDIO CONNECTORS Attach headphones to the Attach a microphone to the connector. connector. OPTICAL DRIVE — For more information about the optical drive see "Using Multimedia" on page 53.
• MultiMediaCard (MMC) • Memory Stick • Memory Stick PRO • xD-Picture Card • Hi Speed-SD • Hi Density-SD IEEE 1394 C O N N E C T O R — Connects devices supporting IEEE 1394 high-speed transfer rates, such as some digital video cameras. VIDEO CONNECTOR Connects video devices, such as a monitor. NETWORK CONNECTOR (RJ-45) NOTICE: The network connector is slightly larger than the modem connector. To avoid damaging the computer, do not plug a telephone line into the network connector.
Back View 1 2 4 3 1 S-video TV-out connector 2 USB connectors (2) 3 AC adapter connector 4 modem connector (RJ-11) 5 USB connector 5 S - V I D E O TV- O U T C O N N E C T O R Connects your computer to a TV. Also connects digital audio-capable devices using the TV/digital audio adapter cable. USB CONNECTORS Connect USB devices, such as a mouse, keyboard, or printer.
A C A D A P T E R C O N N E C T O R — Attaches an AC adapter to the computer. The AC adapter converts AC power to the DC power required by the computer. You can connect the AC adapter with your computer turned on or off. CAUTION: The AC adapter works with electrical outlets worldwide. However, power connectors and power strips vary among countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause fire or equipment damage.
Bottom View 1 2 3 4 10 9 8 7 6 5 1 left speaker 2 consumer IR 3 memory module/coin-cell battery compartment 4 right speaker 5 wireless mini card compartment 6 battery 7 battery charge/health gauge 8 battery release latches (2) 9 air vents 10 hard drive L E F T S P E A K E R — To adjust the volume of the integrated speaker, press the volume control buttons or the mute button.
MEMORY MODULE/COIN-CELL BATTERY COMPARTMENT — Compartment that contains the DIMM B memory module and the coin-cell battery. For additional information, see "Adding and Replacing Parts" on page 135. RIGHT SPEAKER — To adjust the volume of the integrated speaker, press the volume control buttons or the mute button. WIRELESS MINI CARD COMPARTMENT — Compartment for WLAN, WWAN, or WPAN Mini Cards (see "Wireless Mini Cards" on page 154).
Setting Up Your Computer Connecting to the Internet NOTE: ISPs and ISP offerings vary by country. To connect to the Internet, you need a modem or network connection and an Internet service provider (ISP). Your ISP will offer one or more of the following Internet connection options: • DSL connections that provide high-speed Internet access through your existing telephone line or cellular telephone service.
Setting Up Your Internet Connection To set up an Internet connection with a provided ISP desktop shortcut: 1 Save and close any open files, and exit any open programs. 2 Double-click the ISP icon on the Microsoft® Windows® desktop. 3 Follow the instructions on the screen to complete the setup. NOTE: If you are having problems connecting to the Internet, see "E-Mail, Modem, and Internet Problems" on page 107.
Transferring Information to a New Computer You can transfer the following types of data from one computer to another: • E-mail messages • Toolbar settings • Window sizes • Internet bookmarks Use one of the following methods for transferring data: • Windows Easy Transfer wizard, an Easy Transfer Cable, and a USB port • Over a network • Removable media, such as a writable CD Windows Easy Transfer To transfer data using the Windows Easy Transfer wizard: →All Programs→Accessories→System Tools→Wind
Printer Cable Your printer connects to your computer with a USB cable. Your printer may not come with a printer cable, so if you purchase a cable separately, ensure that it is compatible with your printer and computer. If you purchased a printer cable at the same time you purchased your computer, the cable may arrive in the computer’s shipping box. Connecting a USB Printer NOTE: You can connect USB devices while the computer is turned on.
3 Turn on the printer, and then turn on the computer. If the Add New Hardware Wizard window appears, click Cancel. 4 Click Start , and then click Network. 5 Click Add a printer to start the Add Printer Wizard. NOTE: To install the printer driver, see "Reinstalling Drivers and Utilities" on page 128 and the documentation that came with your printer. 6 Click Add a local printer or Add a network, wireless, or Bluetooth printer. 7 Follow the instructions in the Add Printer Wizard.
Line Conditioners NOTICE: Line conditioners do not protect against power interruptions. Line conditioners are designed to maintain AC voltage at a fairly constant level. Uninterruptible Power Supplies NOTICE: Loss of power while data is being saved to the hard drive may result in data loss or file damage. NOTE: To ensure maximum battery operating time, connect only your computer to a UPS. Connect other devices, such as a printer, to a separate power strip that provides surge protection.
Using the Display Adjusting Brightness When a Dell™ computer is running on battery power, you can conserve power by setting the display brightness to the lowest comfortable level. • Press and the up-arrow key to increase brightness on the integrated display only (not on an external monitor). • Press and the down-arrow key to decrease brightness on the integrated display only (not on an external monitor).
You can enhance the legibility of text and change the appearance of images on the screen by adjusting display resolution. As you increase resolution, items appear smaller on the screen. In contrast, lower resolution causes text and images to appear larger and can benefit people with vision impairments. To display a program at a specific resolution, both the video card and the display must support the program, and the necessary video drivers must be installed.
Using the Keyboard and Touch Pad Numeric Keypad The numeric keypad functions like the numeric keypad on an external keyboard. • To enable the keypad, press . The keypad is active. • To disable the keypad, press again. 9 light indicates that the Key Combinations System Functions Opens the Task Manager window.
Power Management Activates a power management mode. You can reprogram this keyboard shortcut to activate a different power management mode using the Advanced tab in the Power Options Properties window (see "Configuring Power Management Settings" on page 49). Microsoft® Windows® Logo Key Functions Windows logo key and Minimizes all open windows. Windows logo key and Restores all minimized windows.
Touch Pad The touch pad detects the pressure and movement of your finger to allow you to move the cursor on the display. Use the touch pad and touch pad buttons as you would use a mouse. 1 2 1 touch pad 2 silk screen depicting scrolling capabilities • To move the cursor, lightly slide your finger over the touch pad. • To select an object, lightly tap once on the surface of the touch pad or use your thumb to press the left touch pad button.
Customizing the Touch Pad You can use the Mouse Properties window to disable the touch pad or adjust the touch pad settings. 1 Click Start , and then click Control Panel. 2 Click Hardware and Sound. 3 Click Mouse. 4 In the Mouse Properties window: • Click the Device Select tab to disable the touch pad. • Click the Touch Pad tab to adjust touch pad settings. 5 Click OK to save the settings and close the window.
Using a Battery Battery Performance NOTE: For information about the Dell warranty for your computer, see the Product Information Guide or separate paper warranty document that shipped with your computer. For optimal computer performance and to help preserve BIOS settings, operate your Dell™ portable computer with the main battery installed at all times. One battery is supplied as standard equipment in the battery bay.
You can check the battery charge before you insert the battery into the computer. You can also set power management options to alert you when the battery charge is low. CAUTION: Using an incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell. The battery is designed to work with your Dell computer. Do not use batteries from other computers with your computer. CAUTION: Do not dispose of batteries with household waste.
The Battery Meter displays the status, battery health, charge level, and charge completion time for the battery in your computer. For more information about QuickSet, right-click the QuickSet icon, and then click Help. Microsoft® Windows® Battery Meter The battery meter indicates the remaining battery charge. To check the battery meter, double-click the icon in the notification area.
original charge capacity remains. If five lights appear, less than 60 percent of the charge capacity remains, and you should consider replacing the battery (see "Battery" on page 182 for more information about the battery operating time). Low-Battery Warning NOTICE: To avoid losing or corrupting data, save your work immediately after a low-battery warning, then connect the computer to an electrical outlet. If the battery runs completely out of power, Sleep state begins automatically.
Configuring Power Management Settings You can use Dell QuickSet or Windows Power Options to configure the power management settings on your computer. • For information on how to use the Dell QuickSet Power Management wizard, right-click the QuickSet icon in the notification area, click Help, and then select Power Management.
Charging the Battery NOTE: Charge time is longer with the computer turned on. You can leave the battery in the computer for as long as you like. The battery’s internal circuitry prevents the battery from overcharging. When you connect the computer to an electrical outlet or install a battery while the computer is connected to an electrical outlet, the computer checks the battery charge and temperature. If necessary, the AC adapter then charges the battery and maintains the battery charge.
To remove the battery: 1 If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions. 2 Ensure that the computer is turned off. 3 Turn the computer over. 4 Slide and click the battery release latches to keep them open. 5 Slide the battery out of the bay. 1 1 battery 2 2 battery release latches (2) To replace the battery, follow the removal procedure in reverse order.
Using a Battery
Using Multimedia Playing Media NOTICE: Do not press down on the optical drive tray when you open or close it. Keep the tray closed when you are not using the drive. NOTICE: Do not move the computer while playing media. 1 Press the eject button on the front of the drive. 2 Place the disc, label side up, in the center of the tray and snap the disc onto the spindle. 3 Push the tray back into the drive. To format media for storing or copying data, see the media software that came with your computer.
A CD player includes the following basic buttons: Play Move backward within the current track Pause Move forward within the current track Stop Go to the previous track Eject Go to the next track A DVD player includes the following basic buttons: Stop Restart the current chapter Play Fast forward Pause Fast reverse Advance a single frame while in pause mode Go to the next title or chapter Continuously play the current title or chapter Go to the previous title or chapter Eject For more information on playin
Playing Media Using Dell Travel Remote The Dell Travel Remote is designed to control Dell Media Direct and Windows Vista™ Media Center. It can work only with specified computers. For more details, go to the Dell Support website at support.dell.com. To play media using Dell Travel Remote: 1 Install the CR2106 coin-cell battery in your remote control. 2 Launch Windows Vista Media Center, and then click Start Programs. → 3 Use the remote control buttons to play media.
1 Infrared Transmitter 2 Page Up 3 Page Down 4 Arrow Up 5 OK/Enter/Select 6 Arrow Right 7 Arrow Down 8 Play/Pause 9 Forward 10 Skip Forward 11 Stop 12 Skip Back 13 Reverse 14 Back 15 Arrow Left 16 Mute 17 Volume Down 18 Volume Up Copying CDs and DVDs This section applies only to computers that have a DVD+/-RW drive. NOTE: Ensure that you observe all copyright laws when copying media. NOTE: The types of optical drives offered by Dell may vary by country.
3 To copy the CD or DVD: • If you have one optical drive, insert the source disc into the drive, ensure that the settings are correct, and then click the Copy Disc button to continue. The computer reads your source disc and copies the data to a temporary folder on your computer hard drive. When prompted, insert a blank disc into the drive and click OK. • If you have two optical drives, select the drive into which you have inserted your source disc and click the Copy Disc button to continue.
Media Type Read Write Rewritable DVD+R Yes Yes No DVD-R Yes Yes No DVD+RW Yes Yes Yes DVD-RW Yes Yes Yes DVD+R DL Yes Yes No DVD-R DL Yes No No Helpful Tips 58 • Use Microsoft® Windows® Explorer to drag and drop files to a CD-R or CD-RW only after you start Roxio Creator and open a Creator project. • Do not burn a blank CD-R or CD-RW to its maximum capacity; for example, do not copy a 650-MB file to a blank 650-MB CD.
Adjusting the Volume NOTE: When the speakers are muted, you do not hear the media playing. 1 Right-click the volume icon in the notification area. 2 Click Open Volume Mixer. 3 Click and drag the bar to slide it up or down to increase or decrease the volume. For more information on volume control options, click Help in the Volume Mixer window. The Volume Meter displays the current volume level, including mute, on your computer.
1 1 Dell MediaDirect button NOTE: You cannot reinstall Dell MediaDirect if you voluntarily reformat the hard drive. You need the installation software to reinstall Dell MediaDirect. Contact Dell for assistance (see "Contacting Dell" on page 175). For more information on using Dell MediaDirect, use the Help menu in the Dell MediaDirect application.
Your TV has either an S-video input connector, a composite video-input connector, or a component video-input connector. Depending on what type of connector is available on your TV, you can use a commercially available S-video cable, composite video cable, or component video cable to connect your computer to your TV.
If you want to connect your computer to a TV or audio device, it is recommended that you connect video and audio cables to your computer in one of the following combinations: • S-video and standard audio • Composite video and standard audio • Component-out video and standard audio NOTE: See the diagrams at the beginning of each subsection to help you determine which method of connection you should use.
1 2 1 standard S-video cable 2 standard audio cable 1 Turn off the computer and the TV and/or audio device that you want to connect. NOTE: If your TV or audio device supports S-video but not S/PDIF digital audio, you can connect an S-video cable directly to the S-video TV-out connector on the computer (without the TV/digital audio adapter cable). 2 Plug one end of the S-video cable into the S-video output connector on the computer.
S-Video and S/PDIF Digital Audio 1 1 S-video TV-out connector 2 2 composite video adapter 1 2 3 64 1 composite video adapter 3 S/PDIF digital audio cable Using Multimedia 2 S-video cable
1 Turn off the computer and the TV and/or the audio device that you want to connect. 2 Connect the composite video adapter to the S-video TV-out connector on your computer. 3 Plug one end of the S-video cable into the S-video output connector on the composite video adapter. 1 composite video adapter 1 2 2 S-video cable 4 Plug the other end of the S-video cable into the S-video input connector on the TV.
Composite Video and Standard Audio 1 2 1 audio input connector 3 composite video adapter 3 2 S-video TV-out connector 1 2 3 66 1 composite video adapter 3 standard audio cable Using Multimedia 2 composite video cable
1 Turn off the computer and the TV and/or audio device that you want to connect. 2 Connect the composite video adapter to the S-video TV-out connector on your computer. 3 Plug one end of the composite video cable into the composite videooutput connector on the composite video adapter. 1 2 1 composite video adapter 2 composite video cable 4 Plug the other end of the composite video cable into the composite videoinput connector on the TV.
Composite Video and S/PDIF Digital Audio 1 1 S-video TV-out connector 2 2 composite video cable 1 2 3 68 1 composite video adapter 3 standard audio cable Using Multimedia 2 composite video cable
1 Turn off the computer and the TV and/or audio device that you want to connect. 2 Connect the composite video adapter to the S-video TV-out connector on the computer. 3 Plug one end of the composite video cable into the composite video-input connector on the composite video adapter. 1 2 1 composite video adapter 2 composite video cable 4 Plug the other end of the composite video cable into the composite videoinput connector on the TV.
Component Video and Standard Audio 1 1 S-video TV-out connector 2 2 component video adapter 1 2 3 70 1 component video adapter 3 standard audio cable Using Multimedia 2 component video adapter
1 Turn off the computer and the TV and/or audio device that you want to connect. 2 Connect the component video adapter to the S-video TV-out connector on your computer. 3 Plug all three ends of the component video cable into the component video-output connectors on the component video adapter. Make sure that the red, green, and blue colors of the cable match the corresponding adapter ports.
Component Video and S/PDIF Digital Audio 1 1 72 S-video TV-out connector Using Multimedia 2 2 composite video cable
1 2 3 1 component video adapter 3 standard audio cable 2 composite video cable 1 Turn off the computer and the TV and/or audio device that you want to connect. 2 Connect the component video adapter to the S-video TV-out connector on the computer. 3 Plug all three ends of the component video cable into the component video-output connectors on the component video adapter. Make sure that the red, green, and blue colors of the cable match the corresponding adapter ports.
2 3 1 1 component video adapter 3 component video cable 2 component video-output connectors 4 Plug all three connectors from the other end of the component video cable into the component video-input connectors on the TV. Make sure that the red, green, and blue colors of the cable match the colors of the TV input connectors. 5 Plug one end of the S/PDIF digital audio cable into the S/PDIF audio connector on the component video adapter.
Enabling S/PDIF Digital Audio 1 Double-click the speaker icon in the Windows notification area. 2 Click the Options menu and then click Advanced Controls. 3 Click Advanced. 4 Click S/PDIF Interface. 5 Click Close. 6 Click OK. Enabling the Display Settings for a TV NOTE: To ensure that the display options appear correctly, connect the TV to the computer before you enable the display settings. 1 Click Start , click Control Panel, and then click Appearance and Personalization.
Using Multimedia
Using ExpressCards ExpressCards provide additional memory, wired and wireless communications, multimedia and security features. For example, you can add an ExpressCard to make wireless wide area network (WWAN) connectivity available on your computer. ExpressCards support two form factors: • ExpressCard/34 (34 mm wide) • ExpressCard/54 (54 mm wide in an L-shape with a 34 mm connector) The 34 mm card fits into both the 34 mm and 54 mm card slots. The 54 mm card only fits into a 54 mm card slot.
Remove the blank before installing an ExpressCard. To remove the blank, see "Removing an ExpressCard or Blank" on page 79. Installing an ExpressCard You can install an ExpressCard while the computer is running. The computer automatically detects the card. ExpressCards are generally marked with a symbol (such as a triangle or an arrow) or a label to indicate which end to insert into the slot. The cards are keyed to prevent incorrect insertion.
The computer recognizes the ExpressCard and automatically loads the appropriate device driver. If the configuration program tells you to load the manufacturer's drivers, use the media that came with the ExpressCard. Removing an ExpressCard or Blank CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Press the latch and remove the card or blank.
Using ExpressCards
Using the Memory Card Reader The memory card reader provides a fast and convenient way to view and share digital photos, music, and videos stored on a memory card. NOTE: A memory card is not a bootable device.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. To install a memory card: 1 Hold the card with the top side of the card facing up. 2 Slide the card into the slot until the card is completely seated in its connector. If you encounter too much resistance, do not force the card. Check the card orientation and try again. The computer recognizes the memory card and automatically loads the appropriate device driver.
Setting Up and Using Networks Setting up a computer network provides connectivity between your computer and the Internet, another computer, or a network. For example, with a network set up in a home or small office you can print to a shared printer, access drives and files on another computer, browse other networks, or access the Internet. You can set up a local area network (LAN) using a network or broadband modem cable or set up a wireless LAN (WLAN).
Setting Up a Network 1 Click Start , and then click Connect To. 2 Click Set up a connection or network. 3 Select an option under Choose a connection option. 4 Click Next, and then follow the instructions in the wizard. Wireless Local Area Network A wireless local area network (WLAN) is a series of interconnected computers that communicate with each other over the air waves rather than through a network cable connected to each computer.
• A wireless router or access point • A wireless network card for each computer that you want to connect to your WLAN • A network cable with a network (RJ-45) connector Checking Your Wireless Network Card Depending on what you selected when you purchased your computer, the computer has a variety of configurations.
Setting Up a New WLAN Using a Wireless Router and a Broadband Modem 1 Contact your Internet service provider (ISP) to obtain specific information about the connection requirements for your broadband modem. 2 Ensure that you have wired Internet access through your broadband modem before you attempt to set up a wireless Internet connection (see "Connecting a Network or Broadband Modem Cable" on page 83). 3 Install any software required for your wireless router.
13 Start your computer and wait until the boot process completes. 14 See the documentation that came with your wireless router to do the following in order to set up the wireless router: • Establish communication between your computer and your wireless router. • Configure your wireless router to communicate with your broadband router. • Find out your wireless router’s broadcast name. The technical term for the name of your router’s broadcast name is Service Set Identifier (SSID) or network name.
To connect to the network: 1 Click Start , and then click Network. 2 Click Network and Sharing on the navigation bar at the top of the Network folder. 3 Click Connect to a network under Tasks. 4 Select your network from the list and click Connect. Once you have configured your computer for a wireless network, another pop-up notifies you that your computer is connected to that network.
Mobile Broadband (or Wireless Wide Area Network) A Mobile Broadband network, also known as a Wireless Wide Area Network (WWAN), is a high-speed digital cellular network that provides Internet access over a much wider geographical area than a WLAN, which typically covers only from 100 to 1000 feet. Your computer can maintain Mobile Broadband network access as long as the computer is within a cellular-data coverage zone. Contact your service provider for coverage of a high-speed digital cellular network.
Checking Your Dell Mobile Broadband Card Depending on what you selected when you purchased your computer, the computer has a variety of configurations. To determine your computer configuration, see one of the following: • Your order confirmation • Microsoft Windows Help and Support To check your Mobile Broadband card in Windows Help and Support: 1 Click Start →Help and Support→Use Tools to view your computer information and diagnose problems.
Use the Dell Mobile Broadband Card Utility to establish and manage a Mobile Broadband network connection to the Internet: 1 Click the Dell Mobile Broadband Card Utility icon notification area to run the utility. in the Windows 2 Click Connect. NOTE: The Connect button changes to the Disconnect button. 3 Follow the instructions on the screen to manage the network connection with the utility. Or 1 Click Start →All Programs→Dell Wireless.
Dell Wi-Fi Catcher™ Network Locator The wireless switch on your Dell computer uses the Dell Wi-Fi Catcher Network Locator to scan for wireless networks in your vicinity. To scan for a wireless network, slide and hold the switch in the momentary position (see "wireless switch" on page 25) for a few seconds.
Securing Your Computer Security Cable Lock NOTE: Your computer does not ship with a security cable lock. A security cable lock is a commercially available antitheft device. To use the lock, attach it to the security cable slot on your Dell computer. For more information, see the instructions included with the device. NOTICE: Before you buy an antitheft device, ensure that it will work with the security cable slot on your computer. Passwords Passwords prevent unauthorized access to your computer.
When using passwords, observe the following guidelines: • Choose a password that you can remember, but not one that is easy to guess. For example, do not use the names of family members or pets for passwords. • It is recommended that you do not write down your password. If you do write it down, however, ensure that the password is stored in a secure location. • Do not share your password with other people. • Ensure that people are not watching you when you type your password.
• Contact Dell customer service to report the missing computer. Provide the computer Service Tag, the case number, and the name, address, and phone number of the law enforcement agency to which you reported the missing computer. If possible, give the name of the investigating officer. The Dell customer service representative will log your report under the computer Service Tag and record the computer as missing or stolen.
Securing Your Computer
Troubleshooting Dell Technical Update Service The Dell Technical Update service provides proactive e-mail notification of software and hardware updates for your computer. The service is free and can be customized for content, format, and how frequently you receive notifications. To enroll for the Dell Technical Update service, go to support.dell.com/technicalupdate.
NOTE: If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions. 1 Ensure that the computer is connected to an electrical outlet that is known to be working properly. 2 Turn on (or restart) your computer. 3 Start the Dell Diagnostics in one of the following two ways: a When the DELL™ logo appears, press immediately. Select Diagnostics from the boot menu, and then press .
3 When the DELL logo appears, press immediately. NOTE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure, press and release in even intervals until the boot device menu appears. 4 At the boot device menu, use the up- and down-arrow keys to highlight CD/DVD/CD-RW, and then press . NOTE: The Quickboot feature changes the boot sequence for the current boot only.
After you have selected the Test System option from the main menu, the following menu appears. NOTE: It is recommended that you select Extended Test from the menu below to run a more thorough check of the devices in the computer. Option Function Express Test Performs a quick test of system devices. The test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to increase the possibility of tracing the problem quickly.
The following tabs provide additional information for tests run from the Custom Test or Symptom Tree option: Tab Function Results Displays the results of the test and any error conditions encountered. Errors Displays error conditions encountered, error codes, and the problem description. Help Describes the test and any requirements for running the test. Configuration Displays your hardware configuration for the selected device.
Click on the desktop icon to run the application and to access: • Self-help tools such as, Dell Support, PC CheckUp, and Network Assistant • Dell support contact information such as, E-mail, Chat and Phone Numbers • Resources that are specific to your systems such as, Drivers & Downloads, Upgrades and System Information • Other support and service resources such as, DellConnect The top of the Dell Support Center home page displays your system’s model number along with its service tag, express serv
To access Dell Support 3: • Click the Dell Support 3 icon NOTE: The in the notification area. icon functions vary when clicking, double-clicking, or right-clicking. or • →All Programs→Dell Support 3→Dell Support Click the Start Settings. Ensure that the Show icon on the taskbar option is checked. NOTE: If Dell Support 3 is not available from the Start menu, go to support.dell.com and download the software.
Network Assistant Designed specifically for users of Dell systems, the Dell Network Assistant helps simplify the setup, monitoring, troubleshooting, and repair of your network.
Drive Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Fill out the "Diagnostics Checklist" on page 174 as you complete these checks. ENSURE THAT MICROSOFT® WINDOWS® RECOGNIZES THE DRIVE — • Click Start →Computer. If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from recognizing the drive.
TU R N O F F S L E E P S T A T E I N W I N D O W S B E F O R E W R I T I N G T O A C D / D V D — See "Using the Sleep Power State" on page 49 for information on Sleep state. C H A N G E T H E W R I T E S P E E D T O A S L O W E R R A T E — See the help files for your CD or DVD creation software. The drive tray cannot eject 1 Ensure that the computer is shut down.
E-Mail, Modem, and Internet Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: Connect the modem to an analog telephone jack only. The modem does not operate while it is connected to a digital telephone network.
5 Click the COM port for your modem. 6 Click Properties, click the Diagnostics tab, and then click Query Modem to verify that the modem is communicating with Windows. If all commands receive responses, the modem is operating properly. E N S U R E T H A T Y O U A R E C O N N E C T E D T O T H E I N T E R N E T — Ensure that you have subscribed to an Internet service provider. With the Outlook Express e-mail program open, click File.
CD D R I V E C O N T R O L L E R F A I L U R E — The CD drive does not respond to commands from the computer (see "Drive Problems" on page 105). D A T A E R R O R — The hard drive cannot read the data (see "Drive Problems" on page 105). D E C R E A S I N G A V A I L A B L E M E M O R Y — One or more memory modules may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them (see "Memory" on page 146).
H A R D - D I S K D R I V E C O N T R O L L E R F A I L U R E 0 — The hard drive does not respond to commands from the computer. Shut down the computer, remove the hard drive (see "Hard Drive" on page 138), and boot the computer from a CD. Then, shut down the computer, reinstall the hard drive, and restart the computer. If the problem persists, try another drive. Run the Hard Disk Drive tests in the Dell Diagnostics (see "Dell Diagnostics" on page 97).
K E Y B O A R D S T U C K K E Y F A I L U R E — For external keyboards or keypads, check the cable connection. Restart the computer, and avoid touching the keyboard or keys during the boot routine. Run the Stuck Key test in the Dell Diagnostics (see "Dell Diagnostics" on page 97).
NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME PROGRAMS AND TRY AGAIN — You have too many programs open. Close all windows and open the program that you want to use. O P E R A T I N G S YS T E M N O T F O U N D — Reinstall the hard drive (see "Hard Drive" on page 138). If the problem persists, contact Dell (see "Contacting Dell" on page 175). O P T I O N A L R O M B A D C H E C K S U M — The optional ROM has failed. Contact Dell (see "Contacting Dell" on page 175). A R E Q U I R E D .
T I M E - O F - D A Y C L O C K S T O P P E D — The reserve battery that supports the system configuration settings may require recharging. Connect your computer to an electrical outlet to charge the battery. If the problem persists, contact Dell (see "Contacting Dell" on page 175). T I M E - O F - D A Y N O T S E T - P L E A S E R U N T H E S YS T E M S E T U P P R O G R A M — The time or date stored in the system setup program does not match the system clock.
IEEE 1394 Device Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. E N S U R E T H A T T H E IEEE 1394 D E V I C E I S R E C O G N I Z E D B Y W I N D O W S — 1 Click Start Manager. →Control Panel→System and Maintenance→Device NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action.
CHECK THE EXTERNAL KEYBOARD — 1 Shut down the computer, wait 1 minute, and then turn it on again. 2 Verify that the numbers, capitals, and scroll lock lights on the keyboard blink during the boot routine. 3 From the Windows desktop, click Start Accessories→Notepad. →All Programs→ 4 Type some characters on the external keyboard and verify that they appear on the display. If you cannot verify these steps, you may have a defective external keyboard.
Lockups and Software Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. The computer does not start C H E C K T H E A C A D A P T E R — Ensure that the AC adapter is firmly connected to the computer and to the electrical outlet. The computer stops responding NOTICE: You might lose data if you are unable to perform an operating system shutdown.
A solid blue screen appears TU R N T H E C O M P U T E R O F F — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off, then restart your computer. Dell MediaDirect problems C H E C K T H E D E L L M E D I A D I R E C T H E L P F I L E F O R I N F O R M A T I O N — Use the Help menu to access Dell MediaDirect Help.
Other software problems CHECK THE SOFTWARE DOCUMENTATION OR CONTACT THE SOFTWARE MANUFACTURER FOR TROUBLESHOOTING INFORMATION — • Ensure that the program is compatible with the operating system installed on your computer. • Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation for information. • Ensure that the program is installed and configured properly. • Verify that the device drivers do not conflict with the program.
Memory Problems Fill out the "Diagnostics Checklist" on page 174 as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. IF YOU RECEIVE AN INSUFFICIENT MEMORY MESSAGE — • Save and close any open files and exit any open programs you are not using to see if that resolves the problem. • See the software documentation for minimum memory requirements.
RESTART THE COMPUTER AND LOG ON TO THE NETWORK AGAIN C H E C K Y O U R N E T W O R K S E T T I N G S — Contact your network administrator or the person who set up your network to verify that your network settings are correct and that the network is functioning. Mobile Broadband (Wireless Wide Area Network [WWAN]) NOTE: The Dell Mobile Broadband Card Utility user’s guide and the Mobile Broadband ExpressCard user’s guide are available through Windows Help and Support (click Start →Help and Support).
Power Problems Fill out the "Diagnostics Checklist" on page 174 as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. C H E C K T H E P O W E R L I G H T — When the power light is lit or blinking, the computer has power. If the power light is blinking, the computer is in Sleep state—press the power button to exit Sleep state. If the light is off, press the power button to turn on the computer.
C O N N E C T T H E C O M P U T E R D I R E C T L Y T O A N E L E C T R I C A L O U T L E T — Bypass power protection devices, power strips, and extension cables to verify that the computer turns on. E L I M I N A T E P O S S I B L E I N T E R F E R E N C E — Turn off nearby fans, fluorescent lights, halogen lamps, or other appliances. A D J U S T T H E P O W E R P R O P E R T I E S — See "Configuring Power Management Settings" on page 49.
Scanner Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: If you need technical assistance for your scanner, contact the scanner’s manufacturer. C H E C K T H E S C A N N E R D O C U M E N T A T I O N — See the scanner documentation for setup and troubleshooting information. U N L O C K T H E S C A N N E R — Ensure that your scanner is unlocked.
No sound from external speakers E N S U R E T H A T T H E S U B W O O F E R A N D T H E S P E A K E R S A R E T U R N E D O N — See the setup diagram supplied with the speakers. If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion. A D J U S T T H E W I N D O W S V O L U M E C O N T R O L — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.
C H E C K T H E M O U S E C A B L E — Shut down the computer, disconnect the mouse cable and check it for damage, then firmly reconnect the cable. If you are using a mouse extension cable, disconnect it and connect the mouse directly to the computer. TO V E R I F Y T H A T T H E P R O B L E M I S W I T H T H E M O U S E , C H E C K T H E T O U C H P A D — 1 Shut down the computer. 2 Disconnect the mouse. 3 Turn on the computer.
C H E C K T H E B A T T E R Y — If you are using a battery to power your computer, the battery charge may be depleted. Connect the computer to an electrical outlet using the AC adapter, and then turn on the computer. TE S T T H E E L E C T R I C A L O U T L E T — Ensure that the electrical outlet is working by testing it with another device, such as a lamp. C H E C K T H E AC A D A P T E R — Check the AC adapter cable connections. If the AC adapter has a light, ensure that the light is on.
S E E "E R R O R M E S S A G E S " — If an error message appears, see "Error Messages" on page 108. If only part of the display is readable CONNECT AN EXTERNAL MONITOR — 1 Shut down your computer and connect an external monitor to the computer. 2 Turn on the computer and the monitor, and then adjust the monitor brightness and contrast controls. If the external monitor works, the computer display or video controller may be defective. Contact Dell (see "Contacting Dell" on page 175).
Identifying Drivers If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver. 1 Click Start , and then right-click Computer. 2 Click Properties→Device Manager. NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue.
Using the Drivers and Utilities Media If using Device Driver Rollback or System Restore (see "Restoring Your Operating System" on page 131) does not resolve the problem, reinstall the driver from your Drivers and Utilities media. 1 With the Windows desktop displayed, insert your Drivers and Utilities media. If this is your first time to use your Drivers and Utilities media, continue to step 2. If not, proceed to step 5.
Manually Reinstalling Drivers NOTE: If your computer has a Consumer IR port and you are reinstalling a Consumer IR driver, you must first enable the Consumer IR port in the system setup program (see "Using the System Setup Program" on page 185) before continuing with the driver installation (see "Reinstalling Drivers and Utilities" on page 128). For information about components installed on your computer, see "Determining Your Computer’s Configuration" on page 19.
To start the Hardware Troubleshooter: 1 Click Start →Help and Support. 2 In the Find an answer section, click Troubleshooting. OR Type hardware troubleshooter in the search field, then press . 3 In the search results, select the option that best describes the problem and follow the remaining troubleshooting steps. NOTE: If you do not find the answer in the items categorized in Troubleshooting, you can get Online Help by typing in your question in the Search Help field at the top of the window.
Using Windows Vista System Restore The Windows Vista operating system provides System Restore to allow you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, software, or other system settings have left the computer in an undesirable operating state. See the Windows Help and Support Center for information on using System Restore. To access the Windows Help and Support Center, click Start Support.
NOTICE: Before you restore the computer to an earlier operating state, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete. 1 Click Start →Control Panel→System and Maintenance→Back Up and Restore Center.. 2 In the Tasks list, click Repair Windows using System Restore. 3 Click Continue in the User Account Control (UAC) dialog box asking for permission to run the application.
Restoring the Computer to the Default Factory Configuration The Dell Factory Image Restore option allows you to restore your hard drive back to its original factory configuration as when you first ordered it from Dell. This option appears on Dell computers that were originally pre-installed with Windows Vista™ and does not include computers purchased through the Express Upgrade promotion or computers that were upgraded to Windows Vista from another version of Windows.
Adding and Replacing Parts Before You Begin This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: • You have performed the steps in "Turning Off Your Computer" on page 135 and "Before Working Inside Your Computer" on page 136. • You have read the safety information in your Dell Product Information Guide.
3 Ensure that the computer and any attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.
4 Disconnect your computer and all attached devices from their electrical outlets. NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer. NOTE: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. 5 Turn the computer over. 6 Slide and click the battery release latches. 7 Slide the battery out of the battery bay.
Hard Drive Depending on the configuration you ordered, your computer may have two hard drives: a primary hard drive and an optional secondary hard drive. CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
1 1 captive screws (2) 2 2 hard drive cover NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge" in the Product Information Guide). 4 Using the pull-tab on the hard drive, pull the hard drive out of the hard drive bay.
1 4 2 3 1 secondary hard drive bay 2 screws (3) 3 primary hard drive 4 pull-tab Replacing the Hard Drive 1 Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector. NOTICE: If you are installing only one hard drive, ensure you install the new drive in the primary hard drive bay. NOTE: The secondary hard drive is optional.
Returning a Hard Drive to Dell Return your old hard drive to Dell in its original, or comparable, foam packaging. Otherwise, the hard drive may be damaged in transit. 2 1 1 foam packaging 2 hard drive Optical Drive CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. Removing the Optical Drive 1 Follow the procedures in "Before You Begin" on page 135. 2 Turn the computer over.
1 2 3 1 optical drive 3 locking screw 2 notch Replacing the Optical Drive 1 Slide the optical drive into the bay. 2 Replace and tighten the locking screw. Hinge Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
Removing the Hinge Cover 1 Follow the procedures in "Before You Begin" on page 135. 2 Open the display as far as it will open. NOTICE: To avoid damage to the hinge cover, do not lift the cover on both sides simultaneously. 3 Insert a plastic scribe into the indent to lift the hinge cover on the right side. 4 Ease the hinge cover up, moving from right to left, and remove it. 1 2 1 hinge cover 2 scribe Replacing the Hinge Cover 1 Insert the left edge of the hinge cover.
Keyboard For more information about the keyboard, see "Using the Keyboard and Touch Pad" on page 41. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
2 3 1 4 1 keyboard 2 screws (4) 3 notch on keyboard 4 tab on computer base Replacing the Keyboard 1 Hook the tabs and the keyboard connector along the front edge of the keyboard into the palmrest, and place the notch on the top of the keyboard on the tab on the base of the computer. 2 Keeping the keyboard flat against the computer base, slide the tabs on the bottom of the keyboard under the palmrest, and ensure the tab on the computer base slides into the notch on the top of the keyboard.
2 3 1 4 5 1 tabs (7) 2 keyboard connector 3 notch on keyboard 4 tab on computer base 5 palmrest 3 Replace the four screws on the top of the keyboard. Memory CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. You can increase your computer memory by installing memory modules on the system board. See "Specifications" on page 177 for information on the memory supported by your computer.
Your computer has two user-accessible SODIMM sockets, one accessed from beneath the keyboard (DIMM A), and the other accessed from the bottom of the computer (DIMM B). NOTICE: If your computer has only one memory module, install the memory module in the connector labeled “DIMMA.” NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled “DIMMA” before you install a module in the connector labeled “DIMMB.
1 2 1 memory module (DIMM A) 2 securing clips (2) Replacing the DIMM A Memory Module NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). 1 Align the notch in the module edge connector with the tab in the connector slot. 2 Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place.
1 2 1 tab 2 notch 3 Replace the keyboard and hinge cover. 4 Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet. 5 Turn on the computer. As the computer boots, it detects the additional memory and automatically updates the system configuration information. To confirm the amount of memory installed in the computer, click Start →Help and Support→Dell System Information.
1 2 1 memory module/coin-cell battery compartment 2 captive screw NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory module securing clips. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).
1 1 securing clips (2) 2 2 memory module Replacing the DIMM B Memory Module NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). 1 Align the notch in the module edge connector with the tab in the connector slot. 2 Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place.
1 2 1 tab 2 notch NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer. 3 Replace the memory module cover. 4 Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet. 5 Turn on the computer. As the computer boots, it detects the additional memory and automatically updates the system configuration information.
Subscriber Identity Module Subscriber Identity Modules (SIM) identify users uniquely through an International Mobile Subscriber Identity. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: Only Cingular and Vodafone need a SIM. Verizon, Sprint, and Telus do not use SIMs. 1 Follow the procedures in "Before You Begin" on page 135.
Wireless Mini Cards CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer. If you ordered a wireless Mini Card with your computer, the card is already installed.
4 Disconnect the antenna cables from the WLAN card. 2 1 1 antenna cable connectors (2) 2 WLAN card 5 Release the WLAN card by pushing the metal securing tabs toward the back of the computer until the card pops up slightly. 6 Lift the WLAN card out of its system board connector.
2 1 1 metal securing tabs (2) 2 WLAN card Replacing a WLAN Card NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card. NOTICE: To avoid damage to the WLAN card, never place cables under the card. 1 Insert the WLAN card connector at a 45-degree angle into the system board connector labeled "WLAN".
3 Connect the appropriate antenna cables to the WLAN card you are installing: If the WLAN card has two triangles on the label (white and black), connect the white antenna cable to the connector labeled "main" (white triangle), and connect the black antenna cable to the connector labeled "aux" (black triangle).
3 Loosen the captive screws on the cover of the Mini Card compartment and remove the cover.
4 Disconnect the two antenna cables from the WWAN card. 2 1 1 antenna cable connectors (2) 2 WWAN card 5 Release the WWAN card by pushing the metal securing tabs toward the back of the computer until the card pops up slightly. 6 Lift the WWAN card out of its system board connector.
2 1 1 metal securing tabs (2) 2 WWAN card Replacing a WWAN Card NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card. NOTICE: To avoid damage to the WWAN card, never place cables under the card. 1 Insert the WWAN card connector at a 45-degree angle into the system board connector labeled "WWAN".
3 Connect the black antenna cable with a gray stripe to the connector labeled "aux" (black triangle) and connect the white antenna cable with a gray stripe to the connector labeled "main" (white triangle). 4 Secure unused antenna cables in the protective mylar sleeve. 5 Replace the cover and tighten the captive screws. Removing a WPAN Card 1 Follow the procedures in "Before You Begin" on page 135. 2 Turn the computer over.
Replacing a WPAN Card NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors on the card and on the system board, and realign the card. NOTICE: To avoid damage to the WPAN card, never place cables under the card. 1 Insert the WPAN card connector at a 45-degree angle into the system board connector labeled "WPAN". 2 Press the other end of the WPAN card down into the securing tabs until the card clicks into place.
1 3 2 1 securing tabs (2) 3 card 2 cable Replacing the Card 1 Replace the card at an angle to slide it under the securing tabs in the card compartment. 2 Connect the cable to the card. Coin-Cell Battery CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing the Coin-Cell Battery 1 Follow the procedures in "Before You Begin" on page 135. 2 Turn the computer over. 3 Loosen the captive screw on the memory module/coin-cell battery cover (see "Bottom View" on page 31), and remove the cover. 4 Disconnect the coin-cell battery cable from the system board. 1 1 coin-cell battery 3 battery cable connector 2 2 mylar sleeve 5 Slide the battery out of the mylar sleeve.
Dell™ QuickSet Features NOTE: This feature may not be available on your computer. Dell QuickSet provides you with easy access to configure or view the following types of settings: • Network connectivity • Power management • Display • System information Depending on what you want to do in Dell QuickSet, you can start it by either clicking, double-clicking, or right-clicking the QuickSet icon in the Microsoft® Windows® notification area.
Dell™ QuickSet Features
Traveling With Your Computer Identifying Your Computer • Attach a name tag or business card to the computer. • Write down your Service Tag and store it in a safe place away from the computer or carrying case. Use the Service Tag if you need to report a loss or theft to law enforcement officials and to Dell. • Create a file on the Microsoft® Windows® desktop called if_found. Place information such as your name, address, and phone number in this file.
• Protect the computer, the batteries, and the hard drive from hazards such as extreme temperatures and overexposure to sunlight, dirt, dust, or liquids. • Pack the computer so that it does not slide around in the trunk of your car or in an overhead storage compartment. Travel Tips NOTICE: Do not move the computer while using the optical drive to prevent loss of data. NOTICE: Do not check the computer as baggage.
Getting Help Obtaining Assistance CAUTION: If you need to remove the computer cover, first disconnect the computer power and modem cables from all electrical outlets. If you experience a problem with your computer, you can complete the following steps to diagnose and troubleshoot the problem: 1 See "Troubleshooting" on page 97 for information and procedures that pertain to the problem your computer is experiencing. 2 See "Dell Diagnostics" on page 97 for procedures on how to run Dell Diagnostics.
When prompted by Dell's automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel. If you do not have an Express Service Code, open the Dell Accessories folder, double-click the Express Service Code icon, and follow the directions. For instructions on using the Dell Support, see "Technical Support and Customer Service" on page 170. NOTE: Some of the following services are not always available in all locations outside the continental U.S.
You can access Dell Support through the following websites and e-mail addresses: • Dell Support websites support.dell.com support.jp.dell.com (Japan only) support.euro.dell.com (Europe only) • Dell Support e-mail addresses mobile_support@us.dell.com support@us.dell.com la-techsupport@dell.com (Latin America and Caribbean countries only) apsupport@dell.com (Asian/Pacific countries only) • Dell Marketing and Sales e-mail addresses apmarketing@dell.com (Asian/Pacific countries only) sales_canada@dell.
Automated Order-Status Service To check on the status of any Dell products that you have ordered, you can go to support.dell.com, or you can call the automated order-status service. A recording prompts you for the information needed to locate and report on your order. For the telephone number to call for your region, see "Contacting Dell" on page 175.
4 Include any accessories that belong with the item(s) being returned (power cables, software floppy disks, guides, and so on) if the return is for credit. 5 Pack the equipment to be returned in the original (or equivalent) packing materials. You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted.
Diagnostics Checklist Name: Date: Address: Phone number: Service Tag (bar code on the back or bottom of the computer): Express Service Code: Return Material Authorization Number (if provided by Dell support technician): Operating system and version: Devices: Expansion cards: Are you connected to a network? Yes No Network, version, and network adapter: Programs and versions: See your operating system documentation to determine the contents of the system’s start-up files.
Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Visit support.dell.com.
Getting Help
Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start , click Help and Support, and then select the option to view information about your computer.
ExpressCard (continued) Cards supported ExpressCard/34 (34 mm) ExpressCard/54 (54 mm) 1.5 V and 3.
Ports and Connectors Audio microphone connector, stereo headphone/speakers connector IEEE 1394 4-pin serial connector Consumer IR sensor compatible with Philips RC6 (receive only) Mini Card three Type IIIA Mini-Card slots Modem RJ-11 port Network adapter RJ-45 port S-video TV-out 7-pin mini-DIN connector (optional S-video to composite video adapter cable) USB five 4-pin USB 2.0-compliant connector Video 15-hole connector Communications Modem: Type v.
Video (continued) LCD interface Low Voltage Differential Signaling (LVDS) TV support NTSC or PAL in S-video, composite, and component modes Audio Audio type two-channel high-definition audio codec Audio controller Sigmatel STAC9205 Codec Stereo conversion 24-bit (analog-to-digital and digital-toanalog) Interfaces: Internal Intel High Definition Audio External microphone-in connector, stereo headphones/speakers connector Speaker two 4-ohm speakers Internal speaker amplifier 2 Watts per chann
Display (continued) Operating angle 0° (closed) to 155° Viewing angles: Horizontal ±40° (WXGA+) typical ±65° (WUXGA+) Vertical +15°/–30° (WXGA+) +45°/-55° (WUXGA) Pixel pitch: WXGA+ 0.255 mm WUXGA 0.191 mm Controls brightness can be controlled through keyboard shortcuts (see "Adjusting Brightness" on page 39) Keyboard Number of keys 86/103 (U.S.
Battery Type 9-cell "smart" lithium ion 6-cell "smart" lithium ion Dimensions: Depth 67.6 mm (2.66 in) (9 cell) 47.5 mm (1.87 in) (6 cell) Height 20.4 mm (0.8 in) Width 209.9 mm (8.26 in) Weight 0.48 kg (1.06 lb) (9 cell) 0.33 kg (0.7 lb) (6 cell) Voltage 11.
AC Adapter (continued) Output current 5.62 A (maximum at 4-second pulse) 4.62 A (90 W) (continuous) Output power 90 W Rated output voltage 19.5 +/–1.0 VDC Dimensions: Height 34.2 mm (1.34 in) Width 60.87 mm (2.39 in) Depth 153.45 mm (6.0 in) Weight (with cables) 0.46 kg (1.01 lb) Temperature range: Operating 0° to 35°C (32° to 95°F) Storage –40° to 65°C (–40° to 149°F) Physical Height 44 mm (1.7 in) Width 394 mm (15.5 in) Depth 293 mm (11.
Environmental (continued) Maximum vibration (using a random vibration spectrum that simulates user environment): Operating 0.66 GRMS Storage 1.3 GRMS Maximum shock (Measured with hard drive in operating status and a 2-ms half-sine pulse for operating. Also measured with hard drive in head-parked position and a 2-ms halfsine pulse for storage): Operating 142 G Storage 163 G Altitude (maximum): 184 Operating –15.2 to 3048 m (–50 to 10,000 ft) Storage –15.
Appendix Using the System Setup Program NOTE: Your operating system may automatically configure most of the options available in system setup, thus overriding options that you set through system setup. An exception is the External Hot Key option, which you can disable or enable only through system setup. For more information on configuring features for your operating system, see Windows Help and Support (click Start , and then click Help and Support).
Viewing the System Setup Screen 1 Turn on (or restart) your computer. 2 When the DELL logo appears, press immediately. If you wait too long and the Microsoft Windows logo appears, continue to wait until you see the Windows desktop, then shut down your computer and try again. System Setup Screen NOTE: For information about a specific item on a system setup screen, highlight the item and see the Help area on the screen. On each screen, the system setup options are listed at the left.
• USB Storage Device • CD/DVD/CD-RW drive • Modular bay HDD NOTE: Only devices that are preceded by a number are bootable. During the boot routine, the computer starts at the top of the list and scans each enabled device for the operating system start-up files. When the computer finds the files, it stops searching and starts the operating system.
About Your RAID Configuration RAID Level 0 Configuration A RAID level 0 configuration uses a storage technique known as "data striping" to provide a high data access rate. Data striping is a method of writing consecutive segments, or stripes, of data sequentially across the physical drives to create a large virtual drive. Data striping allows one of the drives to read data while the other drive is searching for and reading the next block.
• Use a can of compressed air to remove dust from between the keys on the keyboard and to remove any dirt or lint from the display. NOTICE: To help prevent damage to the computer or display, do not spray cleaning solution directly onto the display. Only use products specifically designed for cleaning displays, and follow the instructions that are included with the product. • Moisten a soft, lint-free cloth with either water or a display cleaner. Do not use alcohol or an ammonia-based cleaner.
Mouse NOTICE: Disconnect the mouse from the computer before cleaning the mouse If your screen cursor skips or moves abnormally, clean the mouse. Cleaning a Non-Optical Mouse 1 Clean the outside casing of the mouse with a cloth moistened with a mild cleaning solution. 2 Turn the retainer ring on the underside of your mouse counterclockwise, and then remove the ball. 3 Wipe the ball with a clean, lint-free cloth. 4 Blow carefully into the ball cage or use a can of compressed air to dislodge dust and lint.
2 With a soft, lint-free cloth, gently wipe the bottom of the disc (the unlabeled side) in a straight line from the center to the outer edge of the disc. For stubborn dirt, try using water or a diluted solution of water and mild soap. You can also purchase commercial products that clean discs and provide some protection from dust, fingerprints, and scratches. Cleaning products for CDs are also safe to use on DVDs. Dell Technical Support Policy (U.S.
Definition of "Dell-Installed" Software and Peripherals Dell-installed software includes the operating system and some of the software programs that are installed on the computer during the manufacturing process (Microsoft Office, Norton Antivirus, etc). Dell-installed peripherals include any internal expansion cards, or Dell-branded module bay or ExpressCard accessories.
cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient the receiving antenna. • Relocate the system with respect to the receiver. • Move the system away from the receiver. • Plug the system into a different outlet so that the system and the receiver are on different branch circuits.
Appendix
Glossary Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer. A AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
BIOS — basic input/output system — A program (or utility) that serves as an interface between the computer hardware and the operating system. Unless you understand what effect these settings have on the computer, do not change them. Also referred to as system setup. bit — The smallest unit of data interpreted by your computer.
CD-R — CD recordable — A recordable version of a CD. Data can be recorded only once onto a CD-R. Once recorded, the data cannot be erased or written over. CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten). CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once.
device — Hardware such as a disk drive, printer, or keyboard that is installed in or connected to your computer. device driver — See driver. DIMM — dual in-line memory module — A circuit board with memory chips that connects to a memory module on the system board. DIN connector — A round, six-pin connector that conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 keyboard or mouse cable connectors. disk striping — A technique for spreading data over multiple disk drives.
DVD+RW drive — drive that can read DVDs and most CD media and write to DVD+RW (rewritable DVDs) discs. DVI — digital video interface — A standard for digital transmission between a computer and a digital video display. E ECC — error checking and correction — A type of memory that includes special circuitry for testing the accuracy of data as it passes in and out of memory. ECP — extended capabilities port — A parallel connector design that provides improved bidirectional data transmission.
F Fahrenheit — A temperature measurement scale where 32° is the freezing point and 212° is the boiling point of water. FBD — fully-buffered DIMM — A DIMM with DDR2 DRAM chips and an Advanced Memory Buffer (AMB) that speeds communication between the DDR2 SDRAM chips and the system. FCC — Federal Communications Commission — A U.S. agency responsible for enforcing communications-related regulations that state how much radiation computers and other electronic equipment can emit.
H hard drive — A drive that reads and writes data on a hard disk. The terms hard drive and hard disk are often used interchangeably. heat sink — A metal plate on some processors that helps dissipate heat. hibernate mode — A power management mode that saves everything in memory to a reserved space on the hard drive and then turns off the computer. When you restart the computer, the memory information that was saved to the hard drive is automatically restored.
IrDA — Infrared Data Association — The organization that creates international standards for infrared communications. IRQ — interrupt request — An electronic pathway assigned to a specific device so that the device can communicate with the processor. Each device connection must be assigned an IRQ. Although two devices can share the same IRQ assignment, you cannot operate both devices simultaneously.
M Mb — megabit — A measurement of memory chip capacity that equals 1024 Kb. Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems. MB — megabyte — A measurement of data storage that equals 1,048,576 bytes. 1 MB equals 1024 KB. When used to refer to hard drive storage, the term is often rounded to 1,000,000 bytes. MB/sec — megabytes per second — One million bytes per second.
modem — A device that allows your computer to communicate with other computers over analog telephone lines. Three types of modems include: external, PC Card, and internal. You typically use your modem to connect to the Internet and exchange e-mail. module bay — See media bay. MP — megapixel — A measure of image resolution used for digital cameras. ms — millisecond — A measure of time that equals one thousandth of a second. Access times of storage devices are often measured in ms.
PC Card — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of PC Cards. PCI — peripheral component interconnect — PCI is a local bus that supports 32-and 64-bit data paths, providing a high-speed data path between the processor and devices such as video, drives, and networks. PCI Express — A modification to the PCI interface that boosts the data transfer rate between the processor and the devices attached to it.
RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut down your computer. readme file — A text file included with a software package or hardware product. Typically, readme files provide installation information and describe new product enhancements or corrections that have not yet been documented. read-only — Data and/or files you can view but cannot edit or delete.
ScanDisk — A Microsoft utility that checks files, folders, and the hard disk’s surface for errors. ScanDisk often runs when you restart the computer after it has stopped responding. SCSI — small computer system interface — A high-speed interface used to connect devices to a computer, such as hard drives, CD drives, printers, and scanners. The SCSI can connect many devices using a single controller. Each device is accessed by an individual identification number on the SCSI controller bus.
surge protectors — Prevent voltage spikes, such as those that may occur during an electrical storm, from entering the computer through the electrical outlet. Surge protectors do not protect against lightning strikes or against brownouts, which occur when the voltage drops more than 20 percent below the normal AC-line voltage level. Network connections cannot be protected by surge protectors. Always disconnect the network cable from the network connector during electrical storms.
U UAC — user account control— Microsoft Windows® Vista™ security feature that, when enabled, provides an added layer of security between user accounts and access to operating system settings. UMA — unified memory allocation — System memory dynamically allocated to video. UPS — uninterruptible power supply — A backup power source used when the electrical power fails or drops to an unacceptable voltage level. A UPS keeps a computer running for a limited amount of time when there is no electrical power.
virus — A program that is designed to inconvenience you or to destroy data stored on your computer. A virus program moves from one computer to another through an infected disk, software downloaded from the Internet, or e-mail attachments. When an infected program starts, its embedded virus also starts. A common type of virus is a boot virus, which is stored in the boot sectors of a floppy disk.
X XGA — extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1024 x 768. Z ZIF — zero insertion force — A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or its socket. Zip — A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension of .zip.
Glossary
Index Numerics 8-in-1 memory card reader, 81 A audio device connecting, 60 enabling, 75 audio.
connecting audio device, 60 Mobile Broadband network, 89 TV, 60 device status lights description, 22 contacting Dell, 175 display adjusting brightness, 39 adjusting the size of icons, 165 adjusting the size of toolbars, 165 description, 21 resolution, 39 switching the video image, 39 copying CDs general information, 56 helpful tips, 58 how to, 56 copying DVDs general information, 56 helpful tips, 58 how to, 56 D Dell contacting, 175 Dell Diagnostics about, 97 starting from the Drivers and Utilities med
DVD about, 56 drive problems, 105 E End User License Agreement, 14 ergonomics information, 14 error messages, 108 ExpressCard slot description, 25 ExpressCards, 77 blanks, 77, 79 installing, 78 removing, 79 H hard drive description, 25, 32 problems, 106 replacing, 138 returning to Dell, 141 I icons adjusting the size, 165 IEEE 1394 connector description, 28 problems, 114 installing, 154 Internet connection about, 33 options, 33 setting up, 34 K keyboard numeric keypad, 41 problems, 114 removing, 144 sho
M N media playing, 53 network installing WLAN Mini Card, 154 Mobile Broadband, 119 problems, 119 QuickSet, 165 media control buttons Dell MediaDirect button, 59 description, 23 memory DIMM A, 148 DIMM B, 149 installing, 146 removing, 147 network connector description, 28 memory card, 81 blanks, 81-82 installing, 81 reader, 27 removing, 82 types, 81 operating system reinstalling Windows Vista, 132 memory card reader, 81 memory module cover description, 32 messages error, 108 Mini Card installing, 154
printer cable, 36 connecting, 35 problems, 122 setting up, 35 USB, 36 problems blue screen, 117 CD drive, 105 computer crashes, 116-117 computer does not start up, 116 computer stops responding, 116 Dell Diagnostics, 97 Dell MediaDirect, 117 drives, 105 DVD drive, 105 error messages, 108 hard drive, 106 IEEE 1394 connector, 114 keyboard, 114 lockups, 116 network, 119 power, 121 power light conditions, 121 printer, 122 program crashes repeatedly, 116 program stops responding, 116 programs and Windows compati
security cable slot description, 25 T Service Tag, 15 taskbar QuickSet icon, 165 SIM.
U uninterruptible power supply. See UPS UPS, 37 USB connector description, 29 V video problems, 125 video controller determining configuration, 19 wireless turning activity on and off, 165 wizards Program Compatibility wizard, 116 Windows Easy Transfer, 35 WLAN, 154 installing Mini Card, 154 WPAN installing, 161 WWAN .
Index