Dell™ Inspiron™ One 19 Service Manual Technical Overview Before You Begin I/O Cover Computer Stand Optical Drive Decorative Cover Speaker Cover Display Bezel Back Cover Hard Drive I/O Bracket I/O Card Inverter Back Metal Shield System-Board Shield System-Board Fan Memory Module(s) Coin-Cell Battery Wireless Mini-Card Processor Heat Sink Heat-Sink Fans Processor Power Supply System Board Display Camera Speakers System Setup Utility Notes, Cautions, and Warnings NOTE: A NOTE indicates important information
Back to Contents Page Decorative Cover Dell™ Inspiron™ One 19 Service Manual Removing the Decorative Cover Replacing the Decorative Cover WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1. Follow the procedures in Before You Begin. 2. Place the computer face up on a flat surface. 3. Guide the locks on the decorative cover through the holes on the speaker cover. 4. Press down the decorative cover until it snaps into place. 5. Connect your computer and all attached devices to electrical outlets, and turn them on.
Back to Contents Page Back Cover Dell™ Inspiron™ One 19 Service Manual Removing the Back Cover Replacing the Back Cover WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 back cover 2 screws (10) Replacing the Back Cover 1. Follow the procedures in Before You Begin. 2. Lift the chassis from the clean surface. 3. Turn the chassis over and align the screw holes on the chassis with the screw holes on the back cover. 4. Replace the ten screws that secure the back cover to the chassis. 5. Replace the display bezel (see Replacing the Display Bezel). 6. Replace the speaker cover (see Replacing the Speaker Cover). 7.
Back to Contents Page Before You Begin Dell™ Inspiron™ One 19 Service Manual Recommended Tools Turning Off Your Computer Safety Instructions This manual provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in Turning Off Your Computer and Safety Instructions. l You have read the safety information that shipped with your computer.
CAUTION: To avoid damaging the computer, perform the following steps before you begin working inside the computer. 1. Ensure that the work surface is flat and clean to prevent the computer display from being scratched. 2. Turn off your computer (see Turning Off Your Computer) and all attached devices. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 3. Disconnect all telephone or network cables from the computer. 4.
Back to Contents Page Camera Dell™ Inspiron™ One 19 Service Manual Removing the Camera Replacing the Camera WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
Back to Contents Page Wireless Mini-Card Dell™ Inspiron™ One 19 Service Manual Removing the Mini-Card Replacing the Mini-Card WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 Mini-Card 2 screw Replacing the Mini-Card CAUTION: The connectors are keyed to ensure correct insertion. Use of excessive force may damage the connectors. CAUTION: To avoid damage to the Mini-Card, ensure that there are no cables or antenna cables under the Mini-Card. 1. Follow the procedures in Before You Begin. 2. Align the notch on the Mini-Card with the tab in the system-board connector. 3. Insert the Mini-Card at a 45-degree angle into the system-board connector. 4.
Back to Contents Page Coin-Cell Battery Dell™ Inspiron™ One 19 Service Manual Removing the Coin-Cell Battery Replacing the Coin-Cell Battery WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. WARNING: A new battery can explode if it is incorrectly installed.
Replacing the Coin-Cell Battery 1. Follow the procedures in Before You Begin. 2. Insert the new coin-cell battery into the socket with the side labeled "+" facing left and then snap the coin-cell battery into place. 3. Replace the system-board shield (see Replacing the System-Board Shield). 4. Replace the inverter (see Replacing the Inverter). 5. Replace the I/O bracket (see Replacing the I/O Bracket). 6. Replace the back cover (see Replacing the Back Cover). 7.
Back to Contents Page Display Dell™ Inspiron™ One 19 Service Manual Display Panel Display Cable WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty.
5. Connect your computer and all attached devices to electrical outlets, and turn them on. Display Cable Removing the Display Cable 1. Follow the procedures in Before You Begin. 2. Remove the display panel (see Removing the Display Panel). 3. Turn the display panel over. 4. Lift the conductive tape that secures the display cable to the display-panel connector; press the securing clips on either side of the display-panel connector and disconnect the display cable. 5.
Back to Contents Page Display Bezel Dell™ Inspiron™ One 19 Service Manual Removing the Display Bezel Replacing the Display Bezel WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
Back to Contents Page Speaker Cover Dell™ Inspiron™ One 19 Service Manual Removing the Speaker Cover Replacing the Speaker Cover WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
Back to Contents Page Hard Drive Dell™ Inspiron™ One 19 Service Manual Removing the Hard Drive Replacing the Hard Drive WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
3. Connect the hard-drive cable to the connector on the hard drive. CAUTION: Aluminum foil tapes are used for Electro Magnetic Induction (EMI) shielding and for grounding the components. To avoid damaging the hard drive, ensure that you affix the aluminum foil tapes after replacing the hard drive. NOTE: Aluminum foil tapes will be shipped with the new hard drive. 4. Affix the aluminum foil tapes on the hard drive. 5. Replace the back cover (see Replacing the Back Cover). 6.
Back to Contents Page Processor Heat Sink Dell™ Inspiron™ One 19 Service Manual Removing the Processor Heat Sink Replacing the Processor Heat Sink WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. WARNING: The heat sink may be very hot during normal operation.
1 captive screws (4) 2 processor heat sink Replacing the Processor Heat Sink CAUTION: Incorrect alignment of the processor heat sink can cause damage to the system board and processor. NOTE: The original thermal grease can be reused if the original processor and processor heat sink are reinstalled together. If either the processor or the processor heat sink is replaced, use the thermal grease provided in the kit to ensure that thermal conductivity is achieved. 1.
Back to Contents Page
Back to Contents Page Heat-Sink Fans Dell™ Inspiron™ One 19 Service Manual Removing the Heat-Sink Fans Replacing the Heat-Sink Fans WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 heat-sink fans (2) 2 screws (4) Replacing the Heat-Sink Fans 1. Follow the procedures in Before You Begin. 2. Align the screw holes on the heat-sink fans with the screw holes on the chassis. Replace the four screws that secure the heat-sink fans to the chassis. 3. Route the heat-sink fan cables through the routing guides on the chassis. 4. Connect the heat-sink fan cables to the connectors on the system board. 5. Replace the processor heat sink (see Replacing the Processor Heat Sink). 6.
Back to Contents Page Inverter Dell™ Inspiron™ One 19 Service Manual Removing the Inverter Replacing the Inverter WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 inverter 2 screws (2) Replacing the Inverter 1. Follow the procedures in Before You Begin. 2. Align the screw holes on the inverter with the screw holes on the system-board shield. Replace the two screws that secure the inverter to the systemboard shield. 3. Connect the inverter cable and display cables to the connectors on the inverter. 4. Slide the tabs on the inverter shield into the slots on the system-board shield.
Back to Contents Page I/O Bracket Dell™ Inspiron™ One 19 Service Manual Removing the I/O Bracket Replacing the I/O Bracket WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
3. Align the screw holes on the I/O bracket with the screw holes on the chassis. Replace the four screws that secure the I/O bracket to the chassis. 4. Replace the back cover (see Replacing the Back Cover). 5. Replace the display bezel (see Replacing the Display Bezel). 6. Replace the speaker cover (see Replacing the Speaker Cover). 7. Replace the decorative cover (see Replacing the Decorative Cover). 8. Replace the optical drive (see Replacing the Optical Drive). 9.
Back to Contents Page I/O Card Dell™ Inspiron™ One 19 Service Manual Removing the I/O Card Replacing the I/O Card WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 I/O card Replacing the I/O Card 1. Follow the procedures in Before You Begin. 2. Align the screw holes on the I/O card with the screw holes on the I/O bracket. Replace the four screws that secure the I/O card to the I/O bracket. 3. Replace the I/O bracket (see Replacing the I/O Bracket). 4. Replace the back cover (see Replacing the Back Cover). 5. Replace the display bezel (see Replacing the Display Bezel). 6. Replace the speaker cover (see Replacing the Speaker Cover). 7.
Back to Contents Page I/O Cover Dell™ Inspiron™ One 19 Service Manual Removing the I/O Cover Replacing the I/O Cover WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. WARNING: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the I/O cover.
Back to Contents Page
Back to Contents Page Back Metal Shield Dell™ Inspiron™ One 19 Service Manual Removing the Back Metal Shield Replacing the Back Metal Shield WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
chassis. CAUTION: Aluminum foil tapes are used for Electro Magnetic Induction (EMI) shielding and for grounding the components. To avoid damaging the back metal shield, ensure that you affix the aluminum foil tapes after replacing the back metal shield. NOTE: Aluminum foil tapes will be shipped with the new back metal shield. 3. Affix the aluminum foil tapes on the back metal shield. 4. Replace the I/O bracket (see Replacing the I/O Bracket). 5. Replace the back cover (see Replacing the Back Cover).
Back to Contents Page Memory Module(s) Dell™ Inspiron™ One 19 Service Manual Removing Memory Module(s) Replacing Memory Module(s) WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 cutouts (2) 2 tab 3 notch 4 memory module 3. 1 Insert the memory module into the connector until the memory module snaps into position. If you insert the memory module correctly, the securing clips snap into the cutouts at each end of the memory module. cutouts (2) 2 securing clip (snapped in position) 4. Replace the system-board shield (see Replacing the System-Board Shield). 5. Replace the inverter (see Replacing the Inverter). 6.
Back to Contents Page Optical Drive Dell™ Inspiron™ One 19 Service Manual Removing the Optical Drive Replacing the Optical Drive WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
6. Connect your computer and all attached devices to electrical outlets, and turn them on.
Back to Contents Page Processor Dell™ Inspiron™ One 19 Service Manual Removing the Processor Replacing the Processor WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
3 processor socket 4 release lever CAUTION: When removing or replacing the processor, do not touch any of the pins inside the processor socket or allow any objects to fall on the pins in the processor socket. 15. Lift the processor to remove it from the processor socket; place it aside in a safe and secure place. Replacing the Processor 1. Follow the procedures in Before You Begin. 2. Lift the release lever to the release position so that the processor socket is ready for the new processor.
9. 10. Pivot the processor socket release lever back towards the processor socket, and snap it into place to secure the processor. Clean the thermal grease from the bottom of the heat sink. CAUTION: Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a requirement for optimal processor operation. 11. Apply the new thermal grease to the top of the processor. CAUTION: Ensure that the processor heat sink is correctly seated and secure.
Back to Contents Page Power Supply Dell™ Inspiron™ One 19 Service Manual Removing the Power Supply Replacing the Power Supply WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.
1 power supply 2 screws (3) Replacing the Power Supply 1. Follow the procedures in Before You Begin. 2. Replace the three screws that secure the power supply to the chassis. 3. Route the power-supply cable and connect the power-supply cable to the connector (PWR_CN1) on the system board. 4. Replace the heat-sink fans (see Replacing the Heat-Sink Fans). 5. Replace the processor heat sink (see Replacing the Processor Heat Sink). 6.
Back to Contents Page System-Board Fan Dell™ Inspiron™ One 19 Service Manual Removing the System-Board Fan Replacing the System-Board Fan WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
Replacing the System-Board Fan 1. Follow the procedures in Before You Begin. 2. Align the screw holes on the system-board fan with the screw holes on the system-board shield. 3. Replace the two screws that secure the system-board fan to the system-board shield. 4. Turn the system-board shield over. 5. Replace the system-board shield (see Replacing the System-Board Shield). 6. Replace the inverter (see Replacing the Inverter). 7. Replace the I/O bracket (see Replacing the I/O Bracket). 8.
Back to Contents Page System-Board Shield Dell™ Inspiron™ One 19 Service Manual Removing the System-Board Shield Replacing the System-Board Shield WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1. Follow the procedures in Before You Begin. 2. Replace the system-board shield by using the securing clips that secure the tabs on the system-board shield. 3. Replace the three screws that secure the system-board shield to the chassis. 4. Replace the inverter (see Replacing the Inverter). 5. Replace the I/O bracket (see Replacing the I/O Bracket). 6. Replace the back cover (see Replacing the Back Cover). 7. Replace the display bezel (see Replacing the Display Bezel). 8.
Back to Contents Page Speakers Dell™ Inspiron™ One 19 Service Manual Removing the Speakers Replacing the Speakers WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
3 screws (4) Replacing the Speakers 1. Follow the procedures in Before You Begin. 2. Route the speaker cable through the routing guides. 3. Connect the speaker cable to the connector (SPKR1) on the system board. For more information on the location of the speakers connector, see System Board Components. 4. Replace the four screws (two on each speaker) that secure the speakers to the chassis. 5. Replace the system-board shield (see Replacing the System-Board Shield). 6.
Back to Contents Page Computer Stand Dell™ Inspiron™ One 19 Service Manual Removing the Computer Stand Replacing the Computer Stand WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
Back to Contents Page System Board Dell™ Inspiron™ One 19 Service Manual Removing the System Board Replacing the System Board Entering the Service Tag in the BIOS WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 system board 2 screws (4) Replacing the System Board 1. Follow the procedures in Before You Begin. 2. Align the screw holes on the system board with the screw holes on the chassis. 3. Replace the four screws that secure the system board to the chassis. 4. Connect all the cables to the system board. 5. Replace the processor (see Replacing the Processor). 6. Replace the processor heat sink (see Replacing the Processor Heat Sink). 7.
NOTE: After you have replaced the system board, enter the computer's Service Tag into the BIOS of the replacement system board. 22. Enter the Service Tag (see Entering the Service Tag in the BIOS). Entering the Service Tag in the BIOS 1. Turn on the computer. 2. Press during POST to enter the system setup program. 3. Navigate to the main tab and enter the service tag in the Service Tag Setting field.
Back to Contents Page System Setup Utility Dell™ Inspiron™ One 19 Service Manual Overview Clearing Forgotten Passwords and CMOS Settings Flashing the BIOS Overview Use system setup utility to: l Change the system configuration information after you add, change, or remove any hardware in your computer l Set or change a user-selectable option such as the user password l Read the current amount of memory or set the type of hard drive installed CAUTION: Unless you are an expert computer user, do not cha
Memory Channel Mode Indicates if the memory is in single or dual channel mode Memory Type Indicates the type of installed memory Main Service Tag Setting Displays the service tag of the computer when the service tag is present Displays a field to input the service tag manually when the service tag is absent System Time Displays current time in hh:mm:ss format System Date Displays the current date in mm/dd/yy format SATA-0 Displays the SATA drive connected to the SATA-0 connector SATA-1 Displays
Removable; SATA; USB; CD/DVD; Network; Disabled (SATA by default) 3rd Boot Device Specifies the boot sequence from the available devices Removable; SATA; USB; CD/DVD; Network; Disabled (USB by default) 4th Boot Device Specifies the boot sequence from the available devices Removable; SATA; USB; CD/DVD; Network; Disabled (CD/DVD by default) 5th Boot Device Specifies the boot sequence from the available devices Removable; SATA; USB; CD/DVD; Network; Disabled (Network by default) Removable Drives Specifi
3. Press the up- and down-arrow keys to move through the list of devices. 4. Press plus (+) or minus (–) to change the boot priority of the device. Clearing Forgotten Passwords and CMOS Settings WARNING: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. WARNING: The computer must be disconnected from the electrical outlet to clear the CMOS setting. CAUTION: Only a certified service technician should perform repairs on your computer.
2. Go to the Dell Support website at support.dell.com. 3. Click Drivers & Downloads® Select Model. 4. Select the type of product in the Select Your Product Family list. 5. Select the product brand in the Select Your Product Line list. 6. Select the product model number in the Select Your Product Model list. NOTE: If you have selected a different model and want to start over again, click Start Over on the top right of the menu. 7. Click Confirm. 8. A list of results appear on the screen.
Back to Contents Page Technical Overview Dell™ Inspiron™ One 19 Service Manual Inside View of Your Inspiron One System Board Components WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance. CAUTION: Only a certified service technician should perform repairs on your computer.
1 inverter connector (INV_CN1) 2 processor socket 3 heat-sink fan connector (SYSFAN1) 4 heat-sink fan connector (CPUFAN1) 5 P4 power socket (PWR_CN1) 6 memory-module connector (DIMM1) 7 memory-module connector (DIMM2) 8 SATA power connector (SATAPWR1) 9 SATA drive connector (SATA1) 10 SATA drive connector (SATA2) 11 I/O panel_2 connector (RISER2) 12 battery socket (BT1) 13 I/O panel_1 connector (RISER1) 14 power switch connector (PWRSW1) 15 speakers connector (SPKR1) 16 CMOS jumper (
Back to Contents Page Dell™ Inspiron™ One 19 Service Manual NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved.
