Dell™ Inspiron™ XPS Service Manual Before You Begin System Components Optical Drive Hard Drive Memory Module Modem Mini PCI Card Internal Card With Bluetooth® Wireless Technology Center Control Cover Keyboard Display Palm Rest Speakers Subwoofer USB Port Board System Fans Microprocessor Thermal-Cooling Assembly Microprocessor Module Video Card/Thermal Cooling Assembly MCH Heat Sink PC Card Reader Cage System Board Battery Latch Assembly Customizable LEDs Flashing the BIOS Pin Assignments for I/O Connectors
Back to Contents Page Battery Latch Assembly Dell™ Inspiron™ XPS Service Manual Removing the Battery Latch Assembly Replacing the Battery Latch Assembly Removing the Battery Latch Assembly CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
2 battery latch assembly 9. Remove the spring from the hook on the bottom panel by lifting it up and away with a screwdriver or a plastic scribe. 1 hook 2 spring 10. Remove the plastic battery latch assembly by twisting the assembly slightly and lifting it out of the channel and away from the bottom panel. 1 battery latch assembly Replacing the Battery Latch Assembly 1. Insert the plastic latch assembly into the channel on the bottom panel and press into place. 2.
Back to Contents Page Before You Begin Dell™ Inspiron™ XPS Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Computer Orientation Screw Identification This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in "Turning Off Your Computer" and "Before Working Inside Your Computer.
3. Disconnect any telephone or network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Close the display and turn the computer upside down on a flat work surface. NOTICE: To avoid damaging the system board, you must remove the main battery before you service the computer. 6. Slide the battery-bay latch release on the bottom of the computer and remove the battery from the bay. 1 battery-bay latch release 2 battery 7.
number of screws and their sizes.
Optical Drive: System Board: Door to Card with Bluetooth® Wireless Technology (1 each) (4 each) (1 each) Back to Contents Page
Back to Contents Page Flashing the BIOS Dell™ Inspiron™ XPS Service Manual NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage. 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. NOTE: If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD. 2. Insert the BIOS update program CD, and turn on the computer.
Back to Contents Page Internal Card With Bluetooth® Wireless Technology Dell™ Inspiron™ XPS Service Manual Removing the Card Replacing the Card Removing the Card CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Coin-Cell Battery Dell™ Inspiron™ XPS Service Manual Removing the Coin-Cell Battery Replacing the Coin-Cell battery Removing the Coin-Cell Battery CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page
Back to Contents Page Microprocessor Module Dell™ Inspiron™ XPS Service Manual Removing the Microprocessor Module Replacing the Microprocessor Module Removing the Microprocessor Module CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw, which indicates the direction to turn the cam screw. 8. Lift the microprocessor module from the ZIF socket. Replacing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force.
Back to Contents Page Display Dell™ Inspiron™ XPS Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly Removing the Display Assembly CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 antenna cables 4. Turn the computer top-side up. 5. Remove the center control cover. 6. Open the display all the way (180 degrees) so that it lies flat against the work surface. 7. Use the pull-tab to disconnect the display cable, and then disengage the display cable from the cable channel. 8. Use the pull-tab to disconnect the LED cable, and then disengage the LED cable from the cable channel. 9. Remove the four M2.
10. Lift the display assembly away from the computer. Replacing the Display Assembly 1. Align the display assembly over the screw holes in the base of the computer. 2. Thread the Mini PCI antenna cables back through the hole in the base of the computer. 3. Replace the four M2.5 x 5-mm screws. 4. Connect the LED cable to the system board. 5. Connect the display cable to the system board. 6. Replace the center control cover. 7.
1 M2.5 x 5-mm screws (4) 2 screw covers (2) 3 rubber display bumpers (6) 4 shoulder screws (2) Removing the Display Bezel CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 tabs 7. Repeat step 6 for the lower-left corner of the bezel. Then use your fingers to release the snaps around the rest of the bezel and lift it away from the cover. 1 display bezel 2 display panel Replacing the Display Bezel 1. Starting at any corner, use your fingers to gently snap the bezel into place to secure it to the display panel. 2. Replace the four M2.5 x 5-mm screws on the front of the bezel. 3. Replace the four shoulder screws and two screw covers. 4.
1 display grounding screw 2 display 3 M2 x 3-mm screws (8) 4 display back cover Removing the Display Panel CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1.
6. Replace the display bezel. Display Latch Removing the Display Latch CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1.
Back to Contents Page System Fans Dell™ Inspiron™ XPS Service Manual Removing the System Fans Replacing the System Fans Removing the System Fans CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 fan 2 M2.5 x 5-mm screws (2) 3 LED system board connector 4 fan system board connector Replacing the System Fans 1. Align and place each fan over its respective screw holes on the system board. 2. Replace the four M2.5 x 5-mm screws (two on each fan). 3. Connect the cables for each fan to the system board.
Back to Contents Page Battery Latch Assembly Dell™ Inspiron™ XPS Service Manual Removing the Battery Latch Assembly Replacing the Battery Latch Assembly Removing the Battery Latch Assembly CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
1 screw 2 battery latch assembly 9. Remove the spring from the hook on the bottom panel by lifting it up and away with a screwdriver or a plastic scribe. 1 hook 2 spring 10. Remove the plastic battery latch assembly by twisting the assembly slightly and lifting it out of the channel and away from the bottom panel. 1 battery latch assembly Replacing the Battery Latch Assembly 1. Insert the plastic latch assembly into the channel on the bottom panel and press into place. 2.
Back to Contents Page Before You Begin Dell™ Inspiron™ XPS Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Computer Orientation Screw Identification This section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in "Turning Off Your Computer" and "Before Working Inside Your Computer.
3. Disconnect any telephone or network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Close the display and turn the computer upside down on a flat work surface. NOTICE: To avoid damaging the system board, you must remove the main battery before you service the computer. 6. Slide the battery-bay latch release on the bottom of the computer and remove the battery from the bay. 7. Turn the computer top-side up.
number of screws and their sizes.
Optical Drive: System Board: Door to Card with Bluetooth® Wireless Technology (1 each) (4 each) (1 each) Back to Contents Page
Back to Contents Page Flashing the BIOS Dell™ Inspiron™ XPS Service Manual NOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage. 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. NOTE: If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD. 2. Insert the BIOS update program CD, and turn on the computer.
Back to Contents Page Internal Card With Bluetooth® Wireless Technology Dell™ Inspiron™ XPS Service Manual Removing the Card Replacing the Card Removing the Card CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Coin-Cell Battery Dell™ Inspiron™ XPS Service Manual Removing the Coin-Cell Battery Replacing the Coin-Cell battery Removing the Coin-Cell Battery CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page
Back to Contents Page Microprocessor Module Dell™ Inspiron™ XPS Service Manual Removing the Microprocessor Module Replacing the Microprocessor Module Removing the Microprocessor Module CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw, which indicates the direction to turn the cam screw. 8. Lift the microprocessor module from the ZIF socket. Replacing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force.
Back to Contents Page Display Dell™ Inspiron™ XPS Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly Removing the Display Assembly CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 antenna cables 4. Turn the computer top-side up. 5. Remove the center control cover. 6. Open the display all the way (180 degrees) so that it lies flat against the work surface. 7. Use the pull-tab to disconnect the display cable, and then disengage the display cable from the cable channel. 8. Use the pull-tab to disconnect the LED cable, and then disengage the LED cable from the cable channel. 9. Remove the four M2.
10. Lift the display assembly away from the computer. Replacing the Display Assembly 1. Align the display assembly over the screw holes in the base of the computer. 2. Thread the Mini PCI antenna cables back through the hole in the base of the computer. 3. Replace the four M2.5 x 5-mm screws. 4. Connect the LED cable to the system board. 5. Connect the display cable to the system board. 6. Replace the center control cover. 7.
1 M2.5 x 5-mm screws (4) 2 screw covers (2) 3 rubber display bumpers (6) 4 shoulder screws (2) Removing the Display Bezel CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 tabs 7. Repeat step 6 for the lower-left corner of the bezel. Then use your fingers to release the snaps around the rest of the bezel and lift it away from the cover. 1 display bezel 2 display panel Replacing the Display Bezel 1. Starting at any corner, use your fingers to gently snap the bezel into place to secure it to the display panel. 2. Replace the four M2.5 x 5-mm screws on the front of the bezel. 3. Replace the four shoulder screws and two screw covers. 4.
1 display grounding screw 2 display 3 M2 x 3-mm screws (8) 4 display back cover Removing the Display Panel CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1.
6. Replace the display bezel. Display Latch Removing the Display Latch CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1.
Back to Contents Page System Fans Dell™ Inspiron™ XPS Service Manual Removing the System Fans Replacing the System Fans Removing the System Fans CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 fan 2 M2.5 x 5-mm screws (2) 3 LEDsystem board connector 4 fan system board connector Replacing the System Fans 1. Align and place each fan over its respective screw holes on the system board. 2. Replace the four M2.5 x 5-mm screws (two on each fan). 3. Connect the cables for each fan to the system board.
Back to Contents Page Hard Drive Dell™ Inspiron™ XPS Service Manual Removing the Hard Drive Replacing the Hard Drive Returning a Hard Drive to Dell CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide.
Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit.
Back to Contents Page Center Control Cover Dell™ Inspiron™ XPS Service Manual Removing the Center Control Cover Replacing the Center Control Cover Removing the Center Control Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
Back to Contents Page Keyboard Dell™ Inspiron™ XPS Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
display panel. 1. Reconnect the keyboard to the system board connector. 2. Slide the bottom of the keyboard into the computer base. NOTE: You may need to push the bottom of the keyboard down slightly to seat the keyboard into the computer base. 3. Replace the two M2.5 x 5-mm screws across the top of the keyboard. 4. Replace the center control cover.
Back to Contents Page Customizable LEDs Dell™ Inspiron™ XPS Service Manual Replacing the Customizable LEDs The system has 3 pairs (total of 6) of Light Emitting Diode sets (LEDs) that can be customized to display a chosen color. These customizable LEDs emit light from the top, front, and sides of the computer. Replacing the Customizable LEDs The LEDs are integrated into other replaceable parts of the computer. To replace an LED set, you must replace the part that holds the LED set.
Back to Contents Page MCH Heat Sink Dell™ Inspiron™ XPS Service Manual Removing the MCH Heat Sink Replacing the MCH Heat Sink Removing the MCH Heat Sink CAUTION: Before you perform the following procedures, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Memory Module Dell™ Inspiron™ XPS Service Manual Removing the Memory Module Replacing the Memory Module Removing the Memory Module CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Replacing the Memory Module NOTE: To get maximum performance/dual-channel memory bandwidth capability, both memory module connectors must contain memory modules and the modules must be of the same size and configuration. NOTE: If a memory module is not installed properly, the computer will not boot. 1. 2. Ground yourself and install the new memory module: a. Align the notch in the module edge connector with the tab in the connector slot. b.
Back to Contents Page Mini PCI Card Dell™ Inspiron™ XPS Service Manual Removing the Mini PCI Card Replacing the Mini PCI Card Removing the Mini PCI Card CAUTION: If you are removing and/or installing a 2.4-GHz (802.11b, 802.11b/g) Mini PCI card, follow the instructions noted below. Only products approved for use in your portable computer may be installed. Approved Mini PCI cards may be purchased only from Dell.
NOTICE: To prevent damage to the Mini PCI card connector, do not use tools to spread the securing clips that secure the card. 5. Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly. 6. Remove the Mini PCI card from the connector at a 45-degree angle. 1 Mini PCI card 2 metal securing tabs (2) Replacing the Mini PCI Card NOTICE: To avoid damaging the antenna cables or the Mini PCI card, never place the cables under the card.
1 antenna cables (2) 3. Replace the cover.
Back to Contents Page Modem Dell™ Inspiron™ XPS Service Manual Removing the Modem Replacing the Modem Removing the Modem CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTICE: Do not disconnect the modem cable from the system board. 5. Disconnect the modem cable from the modem. Replacing the Modem 1. Connect the modem cable to the modem. NOTICE: Ensure that the modem cable is routed correctly when you replace the modem. 2. Connect the modem to the system board. Align the connector on the bottom of the modem with the modem connector on the system board, and press down on the right side of the modem. 3. Replace the M2 x 3-mm screw.
Back to Contents Page Optical Drive Dell™ Inspiron™ XPS Service Manual Removing the Optical Drive Replacing the Optical Drive Your computer ships with a fixed optical drive installed. Removing the Optical Drive NOTICE: To prevent damage to drives, store them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them. 1. Follow the instructions in "Before Working Inside Your Computer." 2.
Back to Contents Page Palm Rest Dell™ Inspiron™ XPS Service Manual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 M2.5 x 8-mm screws (11) 9. Remove the Internal Card With Bluetooth® Wireless Technology. 10. Turn the computer top-side up and disconnect the touch-pad connector from the system board. 11. Remove the LED board connector. 12. Lift the palm rest and remove it from the computer. 1 touch-pad connector 2 LED board connector Replacing the Palm Rest 1. Align the palm rest with the bottom plastics and gently snap into place. 2. Reconnect the touch-pad connector to the system board. 3.
8. Replace the display assembly. 9. Replace the keyboard. 10. Replace the center control cover.
Back to Contents Page PC Card Reader Cage Dell™ Inspiron™ XPS Service Manual Removing the PC Card Reader cage Removing the PC Card Reader cage CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Pin Assignments for I/O Connectors Dell™ Inspiron™ XPS Service Manual USB Connector Video Connector S-Video TV-Out Connector IEEE 1394 Connector USB Connector Pin Signal 1 USB5V+ 2 USBP– 3 USBP+ 4 GND Video Connector Pin Signal Pin Signal 1 CRT_R 9 5V+ 2 CRT_G 10 GND 3 CRT_B 11 MONITOR_DETECT– 4 NC 12 DDC_DATA 5 GND 13 CRT_HS 6 GND 14 CRT_VS 7 GND 15 DDC_CLK 8 GND S-Video TV-Out Connector S-Video Pin S
2 GND 3 DLUMA-L 4 DCRMA-L Composite Video Pin Signal 5 NC 6 DCMPS-L 7 GND IEEE 1394 Connector Pin Signal 1 TPB– 2 TPB+ 3 TPA– 4 TPA+ Back to Contents Page
Back to Contents Page System Board Dell™ Inspiron™ XPS Service Manual Removing the System Board Replacing the System Board Removing the System Board CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
13. Remove the M2 x 3-mm screw that holds the stiffener bracket next to the hard drive cage and remove the stiffener bracket. 1 PC Card connector 2 M2.5 x 5-mm stiffener bracket screw 3 stiffener bracket 4 PC Card connector on system board 14. If applicable, remove the video card/thermal cooling assembly. NOTE: Remove the video card/thermal cooling assembly as a single unit. Do not separate the heat sink from the video card. 15. Remove the MCH thermal-cooling solution. 16.
2 PC Card connector 3 cable connector for internal card with Bluetooth wireless technology 4 speaker connector 5 subwoofer connector 24. Remove the three M2.5 x 5-mm screws from the system board. 1 system board M2.5 x 5-mm screws (4) 25. 1 Remove the system board, slowly easing the connectors out of their access holes on the back and side of the computer base: a. With the back of the computer facing you, grasp the upper-right corner of the system board and lift it slightly. b.
4. Enter the system setup program to update the BIOS on the new system board with the computer Service Tag sequence.
Back to Contents Page Speakers Dell™ Inspiron™ XPS Service Manual Removing the Speakers Replacing the Speakers Removing the Speakers CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
4. Re-route the speaker cables into the cable guides and re-adhere the tape to secure the speaker cables in place on the computer base.
Back to Contents Page System Components Dell™ Inspiron™ XPS Service Manual NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order.
Back to Contents Page Microprocessor Thermal-Cooling Assembly Dell™ Inspiron™ XPS Service Manual Removing the Microprocessor Thermal-Cooling Assembly Replacing the Microprocessor Thermal-Cooling Assembly Removing the Microprocessor Thermal-Cooling Assembly CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide.
Back to Contents Page
Back to Contents Page Dell™ Inspiron™ XPS Service Manual NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. For a complete list of abbreviations and acronyms, see the Dell Inspiron Help file.
Back to Contents Page USB Port Board Dell™ Inspiron™ XPS Service Manual Removing the USB Port Board Replacing the USB Port Board Removing the USB Port Board CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
5. Replace the palm rest. 6. Replace the display assembly. 7. Replace the keyboard. 8. Replace the center control cover. 9. Replace the battery and other items removed in "Before Working Inside Your Computer.
Back to Contents Page Video Card/Thermal Cooling Assembly Dell™ Inspiron™ XPS Service Manual Removing the Video Card/Thermal Cooling Assembly Replacing the Video Card/Thermal Cooling Assembly Removing the Video Card/Thermal Cooling Assembly CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide.
2. Tighten the four captive screws on the video card/thermal cooling assembly.
Back to Contents Page Subwoofer Dell™ Inspiron™ XPS Service Manual Removing the Subwoofer Replacing the Subwoofer Removing the Subwoofer CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page
Back to Contents Page Hard Drive Dell™ Inspiron™ XPS Service Manual Removing the Hard Drive Replacing the Hard Drive Returning a Hard Drive to Dell CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide.
Returning a Hard Drive to Dell Return your old hard drive to Dell in its original or comparable foam packaging. Otherwise, the hard drive may be damaged in transit.
Back to Contents Page Center Control Cover Dell™ Inspiron™ XPS Service Manual Removing the Center Control Cover Replacing the Center Control Cover Removing the Center Control Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
Back to Contents Page Keyboard Dell™ Inspiron™ XPS Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
display panel. 1. Reconnect the keyboard to the system board connector. 2. Slide the bottom of the keyboard into the computer base. NOTE: You may need to push the bottom of the keyboard down slightly to seat the keyboard into the computer base. 3. Replace the two M2.5 x 5-mm screws across the top of the keyboard. 4. Replace the center control cover.
Back to Contents Page Customizable LEDs Dell™ Inspiron™ XPS Service Manual Replacing the Customizable LEDs The system has 3 pairs (total of 6) of Light Emitting Diode sets (LEDs) that can be customized to display a chosen color. These customizable LEDs emit light from the top, front, and sides of the computer. Replacing the Customizable LEDs The LEDs are integrated into other replaceable parts of the computer. To replace an LED set, you must replace the part that holds the LED set.
Back to Contents Page MCH Heat Sink Dell™ Inspiron™ XPS Service Manual Removing the MCH Heat Sink Replacing the MCH Heat Sink Removing the MCH Heat Sink CAUTION: Before you perform the following procedures, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Memory Module Dell™ Inspiron™ XPS Service Manual Removing the Memory Module Replacing the Memory Module Removing the Memory Module CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
Replacing the Memory Module NOTE: To get maximum performance/dual-channel memory bandwidth capability, both memory module connectors must contain memory modules and the modules must be of the same size and configuration. NOTE: If a memory module is not installed properly, the computer will not boot. 1. 2. Ground yourself and install the new memory module: a. Align the notch in the module edge connector with the tab in the connector slot. b.
Back to Contents Page Mini PCI Card Dell™ Inspiron™ XPS Service Manual Removing the Mini PCI Card Replacing the Mini PCI Card Removing the Mini PCI Card CAUTION: If you are removing and/or installing a 2.4-GHz (802.11b, 802.11b/g) Mini PCI card, follow the instructions noted below. Only products approved for use in your portable computer may be installed. Approved Mini PCI cards may be purchased only from Dell.
NOTICE: To prevent damage to the Mini PCI card connector, do not use tools to spread the securing clips that secure the card. 5. Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly. 6. Remove the Mini PCI card from the connector at a 45-degree angle. 1 Mini PCI card 2 metal securing tabs (2) Replacing the Mini PCI Card NOTICE: To avoid damaging the antenna cables or the Mini PCI card, never place the cables under the card.
1 antenna cables (2) 3. Replace the cover.
Back to Contents Page Modem Dell™ Inspiron™ XPS Service Manual Removing the Modem Replacing the Modem Removing the Modem CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
NOTICE: Do not disconnect the modem cable from the system board. 5. Disconnect the modem cable from the modem. Replacing the Modem 1. Connect the modem cable to the modem. NOTICE: Ensure that the modem cable is routed correctly when you replace the modem. 2. Connect the modem to the system board. Align the connector on the bottom of the modem with the modem connector on the system board, and press down on the right side of the modem. 3. Replace the M2 x 3-mm screw.
Back to Contents Page Optical Drive Dell™ Inspiron™ XPS Service Manual Removing the Optical Drive Replacing the Optical Drive Your computer ships with a fixed optical drive installed. Removing the Optical Drive NOTICE: To prevent damage to drives, store them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them. 1. Follow the instructions in "Before Working Inside Your Computer." 2.
Back to Contents Page Palm Rest Dell™ Inspiron™ XPS Service Manual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 M2.5 x 8-mm screws (11) 9. Remove the Internal Card With Bluetooth® Wireless Technology. 10. Turn the computer top-side up and disconnect the touch-pad connector from the system board. 11. Remove the LED board connector. 12. Lift the palm rest and remove it from the computer. 1 touch-pad connector 2 LED board connector Replacing the Palm Rest 1. Align the palm rest with the bottom plastics and gently snap into place. 2. Reconnect the touch-pad connector to the system board. 3.
8. Replace the display assembly. 9. Replace the keyboard. 10. Replace the center control cover.
Back to Contents Page PC Card Reader Cage Dell™ Inspiron™ XPS Service Manual Removing the PC Card Reader cage Removing the PC Card Reader cage CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page Pin Assignments for I/O Connectors Dell™ Inspiron™ XPS Service Manual USB Connector Video Connector S-Video TV-Out Connector IEEE 1394 Connector USB Connector Pin Signal 1 USB5V+ 2 USBP– 3 USBP+ 4 GND Video Connector Pin Signal Pin Signal 1 CRT_R 9 5V+ 2 CRT_G 10 GND 3 CRT_B 11 MONITOR_DETECT– 4 NC 12 DDC_DATA 5 GND 13 CRT_HS 6 GND 14 CRT_VS 7 GND 15 DDC_CLK 8 GND S-Video TV-Out Connector S-Video Pin S
2 GND 3 DLUMA-L 4 DCRMA-L Composite Video Pin Signal 5 NC 6 DCMPS-L 7 GND IEEE 1394 Connector Pin Signal 1 TPB– 2 TPB+ 3 TPA– 4 TPA+ Back to Contents Page
Back to Contents Page Speakers Dell™ Inspiron™ XPS Service Manual Removing the Speakers Replacing the Speakers Removing the Speakers CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
4. Re-route the speaker cables into the cable guides and re-adhere the tape to secure the speaker cables in place on the computer base.
Back to Contents Page System Board Dell™ Inspiron™ XPS Service Manual Removing the System Board Replacing the System Board Removing the System Board CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
1 PC Card connector 2 stiffener bracket screw 3 stiffener bracket 4 PC Card connector on system board 14. If applicable, remove the video card/thermal cooling assembly. NOTE: Remove the video card/thermal cooling assembly as a single unit. Do not separate the heat sink from the video card. 15. Remove the MCH thermal-cooling solution. 16. Remove the microprocessor thermal-cooling assembly. 17. Remove the microprocessor. 18.
3 cable connector for internal card with Bluetooth wireless technology 4 speaker connector 5 subwoofer connector 24. Remove the three M2.5 x 5-mm screws from the system board. 1 system board M2.5 x 5-mm screws (3) 25. 1 Remove the system board, slowly easing the connectors out of their access holes on the back and side of the computer base: a. With the back of the computer facing you, grasp the upper-right corner of the system board and lift it slightly. b.
Back to Contents Page
Back to Contents Page System Components Dell™ Inspiron™ XPS Service Manual NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order.
Back to Contents Page Microprocessor Thermal-Cooling Assembly Dell™ Inspiron™ XPS Service Manual Removing the Microprocessor Thermal-Cooling Assembly Replacing the Microprocessor Thermal-Cooling Assembly Removing the Microprocessor Thermal-Cooling Assembly CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide.
Back to Contents Page
Back to Contents Page Dell™ Inspiron™ XPS Service Manual NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. For a complete list of abbreviations and acronyms, see the Dell Inspiron Help file.
Back to Contents Page USB Port Board Dell™ Inspiron™ XPS Service Manual Removing the USB Port Board Replacing the USB Port Board Removing the USB Port Board CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
5. Replace the palm rest. 6. Replace the display assembly. 7. Replace the keyboard. 8. Replace the center control cover. 9. Replace the battery and other items removed in "Before Working Inside Your Computer.
Back to Contents Page Video Card/Thermal Cooling Assembly Dell™ Inspiron™ XPS Service Manual Removing the Video Card/Thermal Cooling Assembly Replacing the Video Card/Thermal Cooling Assembly Removing the Video Card/Thermal Cooling Assembly CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide.
2. Tighten the four captive screws on the video card/thermal cooling assembly.
Back to Contents Page Subwoofer Dell™ Inspiron™ XPS Service Manual Removing the Subwoofer Replacing the Subwoofer Removing the Subwoofer CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Back to Contents Page
