Dell™ KB813 Smart Card Keyboard User Guide
Content Introduction Setup Using the Keyboard Troubleshooting Specifications Regulatory Certifications Information in this document is subject to change without notice. © 2012 - 2015 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Introduction
Back to Contents Page Overview Congratulations on the purchase of your new Dell Smart Card Keyboard. This user's guide has been developed to provide information that will assist you in the setup and operation of your new smart card keyboard.
Back to Contents Page Setup NOTE: The drivers are already factory installed if the keyboard is purchased with computer. This section is included in case you have to re-load your operating system. Install the Keyboard Connect the Keyboard to any USB port on the computer. The USB port shown in the diagram is at the rear of the computer. USB ports may also be located at the front. Follow the instructions in Install the driver section.
Back to Contents Page System Requirements In order to properly install and operate your Dell Smart Card Keyboard, the following system requirements are necessary: • Windows 2000, Windows XP (32/64 bit), Windows Vista (32/64 bit), Windows 7 (32/64 bit), Windows 8 (32/64 bit), Windows 10 (32/64 bit), Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Linux Ubuntu, OpenSuse, and RedHat.
Back to Contents Page Install the Windows XP driver 1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear: 2.
Back to Contents Page 3. The installation wizard will install the driver. After a successful installation, the system will prompt you with the following message: 4. Select Finish. Your Smartcard Keyboard is now ready for use.
Back to Contents Page Install the Vista driver 1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear: 2. Wizard will install driver.
Back to Contents Page Install the Windows 7 driver 1. When the Dell Smart Card Keyboard is plugged into a USB port the following window will appear: 2. The installation Wizard will install driver.
Back to Contents Page Install the Windows 8 driver 1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear: 2. The installation Wizard will install driver. During installation, the system will prompt you with the following window: 3. When installation is completed, your device is ready to use.
Back to Contents Page Install the Windows 10 driver 1. When the Dell Smart Card Keyboard is plugged into a USB port, the following window will appear: 2. The installation Wizard will install driver.
Back to Contents Page Update the Windows XP driver 1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically. 2. From the Start Menu, open the Control Panel.
Back to Contents Page Update the Windows XP driver 3. Double click System. The following window will be shown: 4. Select Hardware.
Back to Contents Page Update the Windows XP driver 5. Select Device Manager. 6. The following screen will be shown. Select Smart card readers.
Back to Contents Page Update the Windows XP driver 7. Right click on Smart Card Reader Keyboard. The display shows as follows: 8. Select Update Driver.
Back to Contents Page Update the Windows XP driver 9. Select Next. The wizard will install the driver. After a successful installation, the system will prompt you with the following message: 10 .Select Finish. Your devic ce is readyy to use.
Back to Contents Page Update the Windows Vista driver 1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically. 2.
Back to Contents Page Update the Windows Vista driver 3. Select System and Maintenance. 4. Select Device Manager. Then, the operating system will pop up the Windows needs your permission to continue dialog box. Click Continue to install.
Back to Contents Page Update the Windows Vista driver 5. Select Smart Card readers. 6. Right click on USB Smart Smar Card reader.
Back to Contents Page Update the Windows Vista driver 7. Select Update Driver Software. 8. Select Browse my computer for driver software. 9. Insert the drivers CD into the CD/DVD drive, browse to Drivers folder, select Windows, and click Next.
Back to Contents Page Update the Windows Vista driver 10. The installation wizard will install driver.
Back to Contents Page Update the Windows 7 driver 1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically. 2. From the Start Menu, open the Control Panel. 3. Double click System and Security.
Back to Contents Page Update the Windows 7 driver 4. Select Device Manager under System. The following screen displays: 5. Select Smart card readers.
Back to Contents Page Update the Windows 7 driver 6. Click on your right button of the device. The display shows as follows: 7. Select Update Driver.
Back to Contents Page Update the Windows 7 driver 8. Insert the drivers CD into the CD/DVD drive, browse to the Drivers folder, select Windows, and click Next. 9. Select Next. The installation wizard will install the driver. After a successful installation, the system will prompt you g message, g , and the device is ready to use.
Back to Contents Page Update the Windows 8 driver 1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically. 2. Open the Control Panel. 3. Double click System.
Back to Contents Page Update the Windows 8 driver 4. Select Device Manager under System.
Back to Contents Page Update the Windows 8 driver 5. Select Smart card readers and right click on the device. The device shows as follows: 6.
Back to Contents Page Update the Windows 8 driver 7. Insert the drivers CD into the CD/DVD drive, browse to the Drivers folder, select Windows, and click Next. 8. The installation wizard will insta install the driver. After a successful installation, the system will promp prompt you with the following message and your device is now ready to u use.
Back to Contents Page Update the Windows 10 driver 1. With the Smart Card reader connected, the old driver that is built in inside the operating system will be installed automatically. 2. Open the Control Panel. 3. Double Double click System. System.
Back to Contents Page Update the Windows 10 driver 4. Select Device Manager under System.
Back to Contents Page Update the Windows 10 driver 5. Select Smart card readers and right click on the device. The device shows as follows: 6.
Back to Contents Page Update the Windows 10 driver 7. Insert the drivers CD into the CD/DVD drive, browse to the Drivers folder, select Windows, and click Next. 8. The installation Wizard will install the driver. After a successful installation, the system will prompt you with the following message and your device is now ready to use.
Back to Contents Page Using the Smart Card Keyboard Box Contents The Smart Card Keyboard includes the following items: Open the package and remove the contents to begin the installation.
Back to Contents Page Connect Keyboard • Connect the keyboard to any USB port on the computer. • The USB port shown in the diagram is at the rear of the computer. USB ports may also be located at the front.
Back to Contents Page Attach Palm Rest • As an option, you may attach the Palm Rest to the keyboard as shown.
Back to Contents Page Inserting a Smart Card To insert a smart card in the Dell Smart Card keyboard, the side of the smart card with the metallic part (contacts) must face you. In the case of a credit card, your name must face you. If the Dell Smart Card Keyboard is installed properly (see section Setup) and the smart card is inserted correctly, the smart card indicator LED should turn blue (see section LED Indicator for details about smart card indicator).
Back to Contents Page LED indicator On the Dell Smart Card Keyboard, there are four LED indicators: • Three standard keyboard LEDs: Num Lock, Caps Lock, and Scroll Lock.
Back to Contents Page The Windows Keys and Applications Keys There are three specific keys on the keyboard for more convenient use, as described below. The two Windows logo keys located on the keyboard could be used in combination with other keys.
Back to Contents Page Diagnostic and Troubleshooting Diagnostics NOTE 1: The diagnostic program needs to be installed on your system from the CD. NOTE 2: Run this diagnostic software if you are having issues using smart cards with your application. It will be able to determine if the smart card software and hardware are loaded and functioning properly. Install the Diagnostic Program 1. To install the diagnostic program in the CD-ROM. Click DIAGNOSTICS folder, and select the desired language.
Back to Contents Page Diagnostic and Troubleshooting 3. Click Next. 4. Read the agreement and then click Install.
Back to Contents Page Diagnostic and Troubleshooting 5. Then installation starts. 6. Installation completed.
Back to Contents Page Diagnostic and Troubleshooting 7. Click Finish. Run SmartDiag 2.4 1. Execute the diagnostic software SmartDiag.
Back to Contents Page Diagnostic and Troubleshooting 2. Click Start. 3. If no smart card is present, the above screen will appear. Insert a smart card and click Next.
Back to Contents Page Diagnostic and Troubleshooting If the smart card reader and smart card have Passed, this means the software and hardware are both working properly. Failed means the smart card driver or the hardware is not present or is not installed correctly. If this occurs, go to www.dell.com/support to resolve this problem. Smart Card Present: (when selected from the screen above) is The above screen shows that the smart card is inserted and the system is able to read the smart card.
Back to Contents Page Diagnostic and Troubleshooting Smart Card Removed When the smart card is removed, the above screen will appear.
Back to Contents Page Diagnostic and Troubleshooting Troubleshooting My smart card is not detected. A. The driver may not be installed or you may not be using the correct driver. Reinstall the driver (see Reinstall the Driver). B. The reader could be contaminated. Extract and reinsert the smart card several times to dislodge any contaminants such as dust or foreign objects. C. The smart card chip is damaged. Obtain a new smart card. My smart card is detected, but does not work. A.
Back to Contents Page Specifications General Manufacturer Model number Connection type Supported operating systems Liteon KB813t USB Microsoft Windows 2000, Microsoft Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10, Microsoft Windows Server 2003, Windows Server 2008, Microsoft Server 2012, Linux Ubuntu, OpenSuse and RedHat Keyboard interface Keyswitch feeling Rollover USB Rubber dome tactile feedback Pseudo 6-key rollover capability Electrical Power requirements Power consumption Switch act
Back to Contents Page Regulatory Regulatory Model : KB813t Regulatory Notices For additional regulatory information, see the Regulatory Compliance home page on www.dell.com at the following location: www.dell.
Back to Contents Page Certifications Microsoft WHQL Logo The Dell Smart Card Keyboard/Reader has passed WHQL logo testing by Microsoft Windows Hardware Quality Labs. WHQL Logo is a certification provided by Microsoft Windows Hardware Quality Labs. This logo ensures that the hardware and accompanying software for the Dell Smart Card Keyboard are compatible with Microsoft Operating Systems. EMV Level 1 Compliance The Dell Smart card Keyboard is EMV Level 1 compliant.
