Dell™ Remote Console Switch Benutzerhandbuch für die Software
Hinweise HINWEIS: Ein HINWEIS weist auf Informationen hin, die Ihnen helfen, Ihren Rechner effizienter einzusetzen. Zusätzliche Software: Sie erkennen an, dass das SOFTWAREPRODUKT urheberrechtlich geschützte Software von Dell Zulieferfirmen enthalten oder einschließen kann, die in der beiliegenden Dokumentation bzw. in anderen gedruckten oder elektronischen Materialien beschrieben („Zusätzliche Software“) und mit einer entsprechenden Lizenz von diesen Zulieferfirmen zur Verfügung gestellt wird.
Inhalt Produktüberblick 7 Funktionen und Vorteile Umfassende Anpassungsfähigkeit Umfassende Verwaltung der Remote Console Switches Authentifizierung und Autorisierung 7 8 8 9 Systemkomponenten RCS Explorer-Fenster Video Viewer Kompatibilität mit Avocent®-Produkten 9 9 10 10 Bedienfunktionen Benennen von Zielgeräten Zielgeräte-Namensanzeigen Sortieren IPv4- und IPv6-Netzwerkadressfunktionen 11 11 12 12 13 Installation 15 Im Lieferumfang der Software enthalten 15 Unterstützte Betriebssysteme 15
Konfiguration von Switches und Zielgeräten 20 Installieren und Einrichten der Weboberfläche 23 Normalbetrieb der Software Inhaltxxx | xxx4 25 Anzeigen des Systems im Explorer 25 Anpassen der Fensteranzeige 27 Hinzufügen eines Remote Console Switch (Dell oder Avocent) 28 Zugriff auf den Remote Console Switch 37 Starten des VNC- oder RDP-Viewers 40 Ändern von Server- und Switch-Eigenschaften Allgemeine Eigenschaften Eigenschaften des Servernetzwerks Eigenschaften des Switch-Netzwerks Informat
Zuordnen einer Einheit zu einem Standort, einem Aufstellungsort 58 oder einem Verzeichnis Löschen und Umbenennen 59 Anpassen des Explorer-Fensters Ändern der beim Start ausgewählten Ansicht Ändern des Standard-Browsers 61 62 62 Verwalten lokaler Datenbanken Speichern einer Datenbank Laden einer Datenbank Exportieren einer Datenbank 63 63 64 65 Verwenden des Viewers 67 Zugriff auf Server über die RCS-Software 67 Interaktion mit dem angezeigten Server Merkmale des Viewer-Fensters Anpassen des Viewers
Getarnte Verbindung Trennungsmodus Virtual Media Teilung und Unterbrechung Starten von Virtual Media Zuordnen von Virtual Media-Laufwerken Virtual Media-Verbindungsstatus Virtual Media-Sitzungen 99 101 104 106 107 107 109 110 Anhang A: Aktualisieren der RCS-Software 115 Anhang B: Tastatur und Maus 117 Anhang C: TCP-Ports 121 Anhang D: Technischer Kundendienst 123 Inhaltxxx | xxx6
1 Produktüberblick Die Dell™ Remote Console Switch- (RCS-) Software ist eine plattformübergreifende Verwaltungsanwendung, mit der Switches und alle angeschlossenen Server überwacht und gesteuert werden können. Das plattformübergreifende Design stellt Kompatibilität mit den meisten gängigen Betriebssystemen und Hardware-Plattformen sicher. Die RCS Software sorgt für sichere Switch-basierte Authentifizierung, Datenübertragung und Speicherung von Benutzernamen/Kennwort.
Umfassende Anpassungsfähigkeit Die RCS Software kann auf Ihre spezifischen Systemanforderungen zugeschnitten werden. Nutzen Sie vordefinierte Gruppen oder erstellen Sie Ihre eigenen. Erstellen Sie benutzerorientierte Einheiten- und Feldbezeichnungen und Symbole für ein Höchstmaß an Flexibilität und Benutzerfreundlichkeit. Die Verwendung aussagekräftiger Namen erleichtert das Auffinden von Systemeinheiten.
HINWEIS: Für Dell 1081AD- und 2161AD-Switches ist der Dell Remote Access Key (RAK) erforderlich, damit die Switches über den RCS hinzugefügt und verwaltet werden können. Authentifizierung und Autorisierung Die RCS Software gewährt die entsprechenden Zugriffsberechtigungen, so dass mehrere Remote Console Switches über eine einzige Oberfläche verwaltet werden können, anstatt jeden Remote Console Switch einzeln verwalten zu müssen.
Über die Geräteliste im Explorer können Sie ein Gerät in der Liste der Zielgeräte auswählen und eine KVM-Sitzung mit dem Gerät starten. Durch Starten einer KVM-Sitzung (Keyboard, Video & Mouse – Tastatur, Video & Maus) wird ein Video Viewer geöffnet. Über die Liste im Explorer können Sie den zu konfigurierenden Switch auswählen. Video Viewer Benutzer können über den Video Viewer auf Zielgeräte zugreifen und diese Geräte verwalten.
• Serielle VT100-Module (Avocent-Module erhältlich) • Serielle True-Module (Module von Dell und Avocent erhältlich) • Sun-Module (Avocent-Module erhältlich) • PS2M-Module (Avocent-Module erhältlich) HINWEIS: Dell SIP-Module werden an direkt verbundenen Avocent Switches unterstützt. HINWEIS: Serielle True-Module werden von den Dell 1081AD- und 2161AD-Switches nicht unterstützt.
Wenn Sie oder andere Benutzer keinen eindeutigen Namen angeben, wird in einer entsprechenden Meldung angezeigt, dass ein eindeutiger Name erforderlich ist. Zielgeräte-Namensanzeigen Beim Hinzufügen eines Switch werden die vom Switch abgerufenen Zielgerätenamen in der Softwaredatenbank gespeichert. Der Benutzer kann dann das Zielgerät im Explorer umbenennen. Der neue Name wird in der Datenbank gespeichert und in verschiedenen Komponentenfenstern verwendet.
auf- oder absteigender Reihenfolge sortieren. Zum Sortieren einer Anzeige nach Spaltenüberschrift klicken Sie auf den dort angegebenen Pfeil. Die Elemente in der Liste werden entsprechend dieser Spalte sortiert. Ein nach oben zeigender Pfeil weist darauf hin, dass die Liste nach dieser Spaltenüberschrift in aufsteigender Reihenfolge sortiert wurde. Ein nach unten zeigender Pfeil weist darauf hin, dass die Liste nach dieser Spaltenüberschrift in absteigender Reihenfolge sortiert wurde.
xxx | Produktüberblickxxx
2 Installation Stellen Sie vor der Installation der RCS Software auf einem Clientcomputer sicher, dass Sie über alle erforderlichen Komponenten verfügen und dass auf den Zielgeräten und RCS-Clientcomputern die unterstützten Betriebssysteme, Browser und Java Runtime Environment ausgeführt werden. Im Lieferumfang der Software enthalten Die Software wird mit den Einheiten auf einer Remote Console Switch Software-CD geliefert.
• SUSE® Linux Enterprise Server 10 und Server 11 • Ubuntu 8 Server und Workstation Auf den Zielgeräten muss eines der nachstehend aufgeführten Betriebssysteme ausgeführt werden: • Microsoft Windows 2000 Server (32 Bit) und Advanced Server • Microsoft Windows XP Professional und Standard mit Service Pack 3 • Microsoft Windows Server 2003 Web, Standard und Enterprise • Microsoft Windows Server 2008 Web, Standard und Enterprise • Microsoft Windows Vista Standard, Business mit Service Pack 1 und En
• Die Farbpalette muss mindestens 65.536 (16 Bit) Farben aufweisen Unterstützte Browser Auf Computern, die zum Zugriff auf die Weboberfläche verwendet werden, und Clientcomputern, auf denen die Software läuft, muss einer der folgenden Browser installiert sein: • Microsoft Internet Explorer ab Version 6.x SP1 oder höher • Firefox ab Version 2.
Installation unter Linux: 1 Legen Sie die RCS Software-CD-ROM in Ihr CD-ROM-Laufwerk ein. 2 Wenn AutoMount unterstützt wird und aktiviert ist, fahren Sie mit Schritt 3 fort. – oder – Wenn Ihr System AutoMount nicht unterstützt: Mounten Sie den CD-ROM-Datenträger, indem Sie folgenden Befehl ausführen: mount -t iso9660 -ro mode=0555 Ersetzen Sie „Gerät“ durch den Namen der CD-ROM in Ihrem Rechner und „Mountpunkt“ durch den Namen des gewünschten Mountpunkts.
3 Klicken Sie auf die Schaltfläche Aktualisierung. Der Deinstallationsassistent wird gestartet. 4 Klicken Sie auf Deinstallieren und folgen Sie den Anweisungen auf dem Bildschirm. Zum Deinstallieren der Software auf Microsoft Windows-Betriebssystemen mithilfe eines Befehlsfensters führen Sie die folgenden Schritte aus: 1 Öffnen Sie ein Befehlsfenster und wechseln Sie zum RCSInstallationsverzeichnis, das während der Installation verwendet wurde.
Wählen Sie Start – Programme – Dell RCS-Software. Die RCS-Software wird gestartet. So starten Sie die RCS-Software unter Linux: Geben Sie im Anwendungsverzeichnis (standardmäßig: /usr/lib/Dell_Remote_ Console_Switch_Software) den folgenden Befehl ein: ./Dell_Remote_Console_Switch_Software – oder – Geben Sie von (/user/bin) aus die folgende Verknüpfung ein: .
4 Konfigurieren Sie die Namen aller Zielgeräte mit der lokalen grafischen Benutzeroberfläche. 5 Wiederholen Sie die Schritte 3 bis 6 für jeden Switch, den Sie verwalten möchten. 6 Sobald eine Software-Umgebung eingerichtet wurde, wählen Sie Datei – Datenbank – Speichern aus, um eine Kopie der lokalen Datenbank mit allen Einstellungen zu speichern. 7 Auf einem zweiten Computer wählen Sie im Softwaremenü die Befehle Datei – Datenbank – Laden. Suchen Sie die Datei, die Sie gespeichert haben.
3 Sobald der Strom eingeschaltet wird, blinkt die Stromversorgungsanzeige an der Rückseite der Einheit ca. 30 Sekunden lang, während ein Selbsttest durchgeführt wird. Drücken Sie die Eingabetaste, um das Hauptmenü aufzurufen. So konfigurieren Sie die Remote Console Switch-Hardware: 1 Sie sehen das Hauptmenü mit elf Optionen. Wählen Sie Option 1, Netzwerkkonfiguration, aus. 2 Wählen Sie Option 1 aus, um die Netzwerkgeschwindigkeit einzustellen.
Mausbeschleunigung Wenn die Maus während einer Remote-Videositzung nur langsam reagiert, deaktivieren Sie die Mausbeschleunigung im Betriebssystem des Zielgeräts und stellen Sie die Mausbeschleunigung auf jedem Zielgerät auf Langsam oder Keine ein. Installieren und Einrichten der Weboberfläche Wenn Sie eine neue Einheit installiert haben, können Sie die Weboberfläche verwenden, um Einheitenparameter zu konfigurieren und Videositzungen zu starten.
3 Die Weboberfläche wird geöffnet und die Registerkarte Verbindungen wird angezeigt. HINWEIS: Zur Verwendung der Weboberfläche muss Java Runtime Environment (JRE) Version 1.6.0_11 oder höher auf Ihrem Computer installiert sein. Der KVM-Switch versucht, Java auf Ihrem PC zu finden. Wenn Java nicht installiert ist, laden Sie es von der Website http://www.java.com herunter und verknüpfen Sie dann die JNLP-Datei mit Java WebStart.
3 Normalbetrieb der Software Der RCS Software-Explorer (im Folgenden als „Explorer“ bezeichnet) ist die Haupt-Benutzeroberfläche für die Software. Sie können alle unterstützten Einheiten anzeigen, abrufen, verwalten und benutzerdefinierte Gruppierungen erstellen. Anzeigen des Systems im Explorer Beim Starten der Software wird das Explorer-Hauptfenster geöffnet. Der Explorer ist in verschiedene Fenster unterteilt: die Register Ansichtauswahl, das Fenster Gruppenauswahl und das Fenster Einheitenauswahl.
Abbildung 3.1: Explorer-Fenster 1 Menüleiste: Ermöglicht den Zugriff auf viele Funktionen der RCS Software. 2 Ansichtauswahl-Register: Enthält vier Register für die Ansichtauswahl zur Auswahl der Explorer-Ansicht. 3 Gruppenauswahl-Fenster: Enthält eine Baumstrukturanzeige und zeigt die Gruppen an, die im aktuellen Register für die Ansichtauswahl verfügbar sind.
5 Einheitenauswahl-Fenster: Enthält die Suchleiste, die Einheitenliste sowie die entsprechenden Taskschaltflächen für die ausgewählte Ansicht oder Gruppe. 6 Suchleiste: Ermöglicht die Suche in der Datenbank nach Text, der in das Suchfeld eingegeben wird. 7 Einheitenliste: Zeigt eine Liste der Einheiten an, die in der aktuell ausgewählten Gruppe enthalten sind, oder die Ergebnisse der Suche, die über die Suchleiste ausgeführt wurde.
Bildschirmposition zurück. Weitere Informationen zum Unterteilungsfenster und zu Verknüpfungen mit der Baumstrukturanzeige und -steuerung finden Sie unter „Tastatur und Maus“ auf Seite 117. Sie können angeben, welche Ansicht (Einheiten, Geräte, Standorte oder Verzeichnisse) beim Start angezeigt werden soll, oder Sie können diese vom Explorer festlegen lassen. Weitere Informationen finden Sie unter „Anpassen der Fensteranzeige“ auf Seite 27.
Klicken Sie auf die Taskschaltfläche Neuer Remote Console Switch. Der „Neuer Remote Console Switch“-Assistent wird angezeigt. 2 Klicken Sie auf Weiter, um fortzufahren. Das Dialogfeld Produkt-Typ wird angezeigt und Sie werden aufgefordert, den Lieferanten und das Produkt des Remote Console Switch auszuwählen. Abbildung 3.2: Dialogfeld „Produkt-Typ“ 3 Wählen Sie einen Lieferanten aus. Für jeden Lieferanten werden die unterstützten Produktnamen in der Liste Produkt aufgeführt. Wählen Sie ein Produkt aus.
Option Andere. Sobald dieser Switch erkannt wurde, wird er in die Liste Produkt aufgenommen und ist verfügbar, wenn Sie das nächste Mal einen Remote Console Switch hinzufügen. HINWEIS: In jedem Dialogfeld des „Neuer Remote Console Switch“-Assistenten wird der Switch-Typ angegeben, den Sie in der Produktliste ausgewählt haben. 4 Klicken Sie auf Weiter. 5 Sie werden aufgefordert, anzugeben, ob dem Remote Console Switch eine IP-Adresse zugewiesen ist oder nicht. Klicken Sie auf Ja und danach auf Weiter.
b. Ordnen Sie jedem SIP oder Avocent IQ-Modul, das mit einem Switch verbunden ist, den entsprechenden Switch aus den Dropdown-Listen zu. Abbildung 3.3: Dialogfeld „Gestufte Switches konfigurieren“ 10 Wenn Sie die letzte Seite des Remote Console Switch-Assistenten erreicht haben, klicken Sie auf Fertig stellen, um den Assistenten zu verlassen und zum Hauptfenster zurückzukehren. Ihr Remote Console Switch sollte nun im Fenster Einheitenauswahl angezeigt werden.
Klicken Sie auf die Taskschaltfläche Neuer Remote Console Switch. Der „Neuer Remote Console Switch“-Assistent wird angezeigt. 2 Klicken Sie auf Weiter, um fortzufahren. Das Dialogfeld Produkt-Typ wird angezeigt und Sie werden aufgefordert, Lieferanten und Produkt des Remote Console Switch auszuwählen. Abbildung 3.4: Dialogfeld „Produkt-Typ“ 3 Wählen Sie einen Lieferanten aus. Für jeden Lieferanten werden die unterstützten Produktnamen in der Liste Produkt aufgeführt. Wählen Sie ein Produkt aus.
Option Andere. Sobald dieser Switch erkannt wurde, wird er in die Liste Produkt aufgenommen und ist verfügbar, wenn Sie das nächste Mal einen Remote Console Switch hinzufügen. 4 Klicken Sie auf Weiter. 5 Sie werden aufgefordert, anzugeben, ob dem Remote Console Switch eine IP-Adresse zugewiesen ist. Klicken Sie auf Nein und danach auf Weiter. 6 Das Fenster Netzwerkadresse wird angezeigt.
a. Das Feld Vorhandene gestufte Switches enthält eine Liste aller derzeit in der Datenbank definierten Switches. Sie können in dieser Liste einen Eintrag hinzufügen, löschen oder ändern. b. Ordnen Sie jedem SIP oder Avocent IQ-Modul, das mit einem Switch verbunden ist, den entsprechenden Switch aus den Dropdown-Listen zu. Abbildung 3.5: Dialogfeld „Gestufte Switches konfigurieren“ 10 Zum Abschluss klicken Sie auf Fertig stellen, um den Assistenten zu beenden und zum Hauptfenster zurückzukehren.
2 Ein Bildschirm mit dem Adressenbereich wird angezeigt. Führen Sie einen der folgenden Schritte aus: Wenn Sie den IPv4-Modus verwenden, wählen Sie IPv4-Adressbereich verwenden aus und geben Sie in den Feldern Von Adresse und Bis Adresse den Bereich der IP-Adressen ein, den Sie im Netzwerk durchsuchen möchten. IPv4-Adressen werden durch Punkte getrennt eingegeben (xxx.xxx.xxx.xxx.xxx).
neuen Remote Console Switches gefunden an und Sie müssen den Switch manuell hinzufügen. Weitere Informationen finden Sie im vorigen Abschnitt. 5 Klicken Sie auf die hinzuzufügenden Remote Console Switches und dann auf die Schaltfläche Hinzufügen (>), um die Auswahl in die Liste Remote Console Switches hinzufügen zu verschieben. Abbildung 3.6: Dialogfeld „Remote Console Switches auswählen“ 6 Wiederholen Sie Schritt 5 für alle Remote Console Switches, die hinzugefügt werden sollen.
Seite Suchassistent beendet eingeblendet. Klicken Sie auf Fertig stellen, um den Assistenten zu verlassen und zum Hauptfenster zurückzukehren. Die neuen Switches sollten nun im Fenster Einheitenauswahl angezeigt werden. 8 Wenn mindestens ein Switch aus irgendwelchen Gründen nicht der lokalen Datenbank hinzugefügt werden konnte (auch wenn Sie während des Hinzufügens auf Stopp geklickt haben), wird die Seite Nicht alle Remote Console Switches hinzugefügt des Suchassistenten angezeigt.
Abbildung 3.7: Register für Anzeige des Remote Console Switch ausgewählt So melden Sie sich bei einem Remote Console Switch an: 1 Klicken Sie auf das Register Remote Console Switches im Explorer. 2 Doppelklicken Sie auf einen Remote Console Switch im Fenster Einheitenauswahl. – oder – Wählen Sie im Fenster Einheitenauswahl einen Remote Console Switch aus und klicken Sie anschließend auf die Taskschaltfläche Remote Console Switch konfigurieren.
Klicken Sie auf einen Remote Console Switch im Fenster Einheitenauswahl und drücken Sie die Eingabetaste. 3 Falls verfügbar werden die im Cache gespeicherten Anmeldeberechtigungen verwendet. Falls nicht, wird eine Anmeldungsaufforderung angezeigt. Geben Sie Benutzername und Kennwort ein.
Starten des VNC- oder RDP-Viewers Die RCS Software unterstützt benutzerdefinierte VNC-Viewer (Virtual Network Computing) und RDP-Viewer (Remote Desktop Protocol). Wählen Sie zum Starten des VNC- oder des RDP-Viewers das Register Server im RCS-SoftwareExplorer aus. Wählen Sie einen Server aus der Einheitenliste aus. Klicken Sie dann entweder auf die Schaltfläche VNC oder auf RDP rechts unten auf dem Bildschirm.
– oder – Klicken Sie mit der rechten Maustaste auf die Einheit und wählen Sie Eigenschaften aus. Das Dialogfeld Eigenschaften wird angezeigt. Abbildung 3.8: Register „Allgemeine Eigenschaften“ für einen Server 3 Geben Sie den Namen der Einheit ein. Eine doppelte Namensvergabe ist nicht zulässig. 4 (Nur für Server – optional) Wählen Sie den Servertyp aus. Wenn Ihre Auswahl nicht in der Dropdown-Liste angezeigt wird, geben Sie den Namen für den neuen Servertyp in das Textfeld ein.
Zuordnung in das Textfeld ein. Sobald Sie die Eingabe abgeschlossen haben, ist diese Option in der Dropdown-Liste für zukünftige Zuordnungen verfügbar. 7 Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern. – oder – Klicken Sie auf OK, um die neuen Einstellungen zu speichern und das Fenster „Eigenschaften“ zu schließen. – oder – Klicken Sie auf Abbrechen, um das Dialogfeld zu verlassen, ohne die neuen Einstellungen zu speichern.
– oder – Klicken Sie auf OK , um die neuen Einstellungen zu speichern und das Fenster zu schließen. – oder – Klicken Sie auf Abbrechen, um das Dialogfeld zu verlassen, ohne die neuen Einstellungen zu speichern. Eigenschaften des Switch-Netzwerks Wenn Sie Ihr Netzwerk neu konfigurieren möchten, können Sie die IP-Adresse für einen Switch über das Register Netzwerk ändern.
4 Geben Sie die HTTP- und die HTTPS-Portnummern im Feld HTTP-Port bzw. HTTPS-Port ein, wenn Sie die Portnummern für den Remote Console Switch in der seriellen Konsole geändert haben. Weitere Informationen zum Ändern der Portnummern in der seriellen Konsole finden Sie unter „HTTP/HTTPS-Optionen“ auf Seite 52. 5 Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern. – oder – Klicken Sie auf OK, um die neuen Einstellungen zu speichern und das Fenster zu schließen.
4 a. Im Feld Beschreibung können 0 bis 128 Zeichen eingegeben werden. b. Im Feld Kontakt können 0 bis 128 Zeichen eingegeben werden. c. Im Feld Kontakt-Telefonnummer können 0 bis 64 Zeichen eingegeben werden. d. Im Feld Kommentare können 0 bis 256 Zeichen eingegeben werden. Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern. – oder – Klicken Sie auf OK, um die neuen Einstellungen zu speichern und das Fenster zu schließen.
3 Klicken Sie auf das Register Verbindungen, um die Verbindungen des Servers anzuzeigen. Verbindungseigenschaften sind schreibgeschützt und nur für Server verfügbar. Angezeigt werden der Verbindungspfad, der für den Zugriff auf dieses Gerät verwendet wird, sowie der Verbindungstyp, z. B. „Video“. 4 Wenn der Vorgang abgeschlossen ist, klicken Sie auf OK oder Abbrechen, um das Fenster zu schließen.
4 Geben Sie nur für Server im Feld „IP-Adresse“ eine durch Punkte getrennte IP-Adresse oder einen Domänennamen mit 1 - 128 Zeichen ein. Leerzeichen sind nicht zulässig. Eine doppelte Adressvergabe ist zulässig. Sie können IPv4- und IPv6-Adressen verwenden. 5 Geben Sie im Feld „Port“ eine Portnummer zwischen 23 und 65535 ein. Wenn dieses Feld leer ist, wird Port 23 verwendet. 6 Aktivieren oder deaktiveren Sie das Kontrollkästchen Standard verwenden.
bereitstellen, wie die Befehle für Computer unter den Betriebssystemen Windows, Linux und UNIX®, kann die RDP-Anwendung in einem Befehlsfenster des Betriebssystems gestartet werden. So ändern Sie RDP-Eigenschaften: 1 Wählen Sie in der Einheitenliste einen Server aus. 2 Wählen Sie im Remote Console Switch Explorer-Menü Ansicht – Eigenschaften aus. – oder – Klicken Sie auf die Taskschaltfläche Eigenschaften. – oder – Klicken Sie mit der rechten Maustaste auf die Einheit.
8 Geben Sie im Feld unter dem Pfad und dem Namen Befehlszeilenargumente ein. – oder – Klicken Sie zum Einfügen eines vordefinierten Makros an der Cursorposition in der Befehlszeile auf das Listenfeld Makro einfügen und wählen Sie ein Makro aus dem Dropdown-Menü aus. Bei der Ausführung der Anwendung ersetzt die RCS-Software diese Variablen automatisch. 9 Aktivieren oder deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster.
Durchsuchen angezeigt. Klicken Sie auf die Taskschaltfläche Durchsuchen. Das von Ihnen angegebene Netzwerk wird in einem Browser-Fenster geöffnet. Ändern von Server- und Switch-Optionen In der RCS-Software können Sie im Dialogfeld Optionen individuelle Serveroder Switch-Optionen einschließlich Allgemein, HTTP-/HTTPS-Ports, VNC und RDP ändern. Allgemeine Optionen So ändern Sie eine benutzerdefinierte Feldbezeichnung: 1 Wählen Sie Extras – Optionen aus dem Explorer-Menü.
2 Wählen Sie die Feldbezeichnung, die Sie ändern möchten, und klicken Sie auf die Schaltfläche Ändern. Das Dialogfeld Benutzerdefinierte Feldbezeichnung ändern wird angezeigt. 3 Geben Sie die Feldbezeichnung in Singular- und Pluralform ein. Die Länge muss zwischen 1 und 32 Zeichen liegen. Das Feld darf nicht leer bleiben. Leerzeichen in der Mitte sind zulässig, Leerzeichen am Beginn und am Ende des Namens jedoch nicht. 4 Klicken Sie auf OK, um die neue Feldbezeichnung zu speichern.
• Klicken Sie auf eine andere Registerkarte, um weitere Eigenschaften zu ändern. • Klicken Sie auf OK, um die neuen Einstellungen zu speichern. • Klicken Sie auf Abbrechen, um das Dialogfeld zu verlassen, ohne die neuen Einstellungen zu speichern. Ändern der DirectDraw-Unterstützung (nur Windows-Betriebssysteme) Die Software unterstützt DirectDraw.
„Optionen“ ändern. 1 Wählen Sie Extras – Optionen aus dem Explorer-Menü. Das Dialogfeld Optionen wird angezeigt. 2 Klicken Sie auf das Register HTTP-/HTTPS-Ports. 3 Geben Sie die neuen HTTP- und HTTPS-Standard-Portnummern ein. 4 Klicken Sie auf OK. VNC-Optionen Die Software unterstützt benutzerdefinierte VNC-Viewer über die Eigenschaftenseite. Im Register „VNC“ können Sie nach einer benutzerdefinierten VNC-Anwendung suchen und deren Befehlszeilenargumente einschließen.
Klicken Sie zum Einfügen eines vordefinierten Makros an der Cursorposition in der Befehlszeile auf das Listenfeld Makro einfügen und wählen Sie ein Makro aus dem Dropdown-Menü aus. Bei der Ausführung der Anwendung ersetzt die RCS-Software diese Variablen automatisch. 5 Aktivieren bzw. deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster. Wenn es aktiviert ist, wird die benutzerdefinierte VNCAnwendung in einem Befehlsfenster des Betriebssystems gestartet. 6 Klicken Sie auf OK.
Klicken Sie zum Einfügen eines vordefinierten Makros an der Cursorposition in der Befehlszeile auf das Listenfeld Makro einfügen und wählen Sie ein Makro aus dem Dropdown-Menü aus. Bei der Ausführung der Anwendung ersetzt die RCS-Software diese Variablen automatisch. 5 Aktivieren bzw. deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster. Wenn es aktiviert ist, wird die benutzerdefinierte RDPAnwendung in einem Befehlsfenster des Betriebssystems gestartet. 6 Klicken Sie auf OK.
verwenden können. Sie können diese entsprechend der Organisationsstruktur Ihres Unternehmens ändern.Abbildung 3.11 zeigt ein Beispiel für benutzerdefinierte Feldbezeichnungen. Abbildung 3.10: Ausgewähltes Register „Standorte“ Ändern von benutzerdefinierten Feldbezeichnungen Mit benutzerdefinierten Feldbezeichnungen können Sie die Namen der Spaltenüberschriften Standort, Abteilung und Aufstellungsort ändern, die in den Fenstern Gruppen und Einheitenauswahl in der Software angezeigt werden.
Abbildung 3.11: Beispiel für geänderte benutzerdefinierte Felder So erstellen Sie einen neuen Standort, eine neue Abteilung oder einen neuen Aufstellungsort: 1 Wählen Sie im Explorer-Menü Ansicht – Eigenschaften. – oder – Klicken Sie auf die Taskschaltfläche Eigenschaften. Das Dialogfeld Eigenschaften wird angezeigt. 2 Klicken Sie auf das Register Allgemein und wählen Sie das Dropdown-Menü für Standort, Abteilung oder Aufstellungsort aus.
– oder – Klicken Sie mit der rechten Maustaste auf den Knoten Verzeichnisse und wählen Sie Neues Verzeichnis aus. Das Dialogfeld Neues Verzeichnis wird angezeigt. 3 Geben Sie einen Namen für das Verzeichnis mit 1 bis 32 Zeichen ein. Bei den Verzeichnisnamen wird nicht zwischen Groß- und Kleinschreibung unterschieden. Es kann eine beliebige Zeichenkombination über die Tastatur eingegeben werden. Leerzeichen in der Mitte sind zulässig, Leerzeichen am Beginn und am Ende des Namens jedoch nicht.
3 Wählen Sie die Standort-, Aufstellungsort- oder Verzeichnis-Kategorie aus der Dropdown-Liste aus. 4 Wählen Sie in der Liste der verfügbaren Ziele die Zieloption aus, der die Einheit innerhalb der ausgewählten Kategorie zugewiesen werden kann. Diese Liste enthält u. U. keinen Eintrag, wenn noch kein Standort, Aufstellungsort oder Verzeichnis in der lokalen Datenbank definiert wurde. 5 Klicken Sie auf OK, um die Einstellungen zu speichern.
Die Funktion zum Umbenennen ist ebenfalls kontextabhängig. In der Einheitenliste können Sie einen Remote Console Switch oder Server auswählen und umbenennen. In der Baumstruktur des Fensters Gruppenauswahl können Sie Servertypen, Standorte, Abteilungen und Verzeichnisse auswählen und umbenennen. So löschen Sie einen Remote Console Switch oder Server: 1 Wählen Sie die zu löschenden Einheiten im Fenster Einheitenauswahl aus. 2 Wählen Sie Bearbeiten – Löschen aus.
3 Klicken Sie auf Ja, um den Löschvorgang zu bestätigen. In Abhängigkeit von Ihrer Konfiguration können zusätzliche Meldungen angezeigt werden. Reagieren Sie auf diese Meldungen wie erforderlich. Das Element wird gelöscht. – oder – Klicken Sie auf Nein, um den Vorgang abzubrechen. So benennen Sie eine Einheit, einen Standort, eine Abteilung oder ein Verzeichnis um: 1 Wählen Sie im Fenster Gruppenauswahl in der RCS-Software den Servertyp, den Standort, die Abteilung oder das Verzeichnis aus.
Eine Bildschirmunterteilung, die von oben nach unten verläuft, trennt das Fenster Gruppenauswahl vom Fenster Einheitenauswahl. Sie können die Unterteilung nach links oder rechts bewegen, um den Anzeigebereich des Fensters Gruppenauswahl bzw. Einheitenauswahl zu ändern. Bei jedem neuen Start des Explorers wird die Unterteilung wieder an ihrer StandardBildschirmposition angezeigt.
bestimmten Browser für diesen Server aufrufen. So ändern Sie den Standard-Browser: 1 Wählen Sie Extras – Optionen aus dem Explorer-Menü. Das Dialogfeld Optionen wird angezeigt. 2 Deaktivieren Sie das Kontrollkästchen Standard-Browser starten. Die Schaltfläche Durchsuchen wird aktiviert. 3 Klicken Sie auf die Schaltfläche Durchsuchen und navigieren Sie durch die Verzeichnisstruktur zum entsprechenden Browser. 4 Klicken Sie auf OK, um die neue Browser-Auswahl zu speichern.
Während die Datenbank gespeichert wird, kann keine andere Aktion ausgeführt werden und alle anderen Fenster müssen geschlossen sein. Wenn andere Fenster geöffnet sind, wird eine Meldung mit der Aufforderung angezeigt, den Vorgang entweder fortzusetzen und alle geöffneten Fenster zu schließen oder den Vorgang und das Speichern der Datenbank abzubrechen. So speichern Sie eine Datenbank: 1 Wählen Sie im RCS Explorer-Menü Datei – Datenbank – Speichern aus. Das Dialogfeld Datenbank speichern wird angezeigt.
3 Klicken Sie auf Laden. Während des Ladens wird eine Statusanzeige eingeblendet. Nach Beendigung dieses Vorgangs wird eine Meldung angezeigt, dass das Laden erfolgreich abgeschlossen wurde. Danach wird wieder das Hauptfenster angezeigt. Exportieren einer Datenbank Mit dieser Funktion können Sie Felder aus der lokalen Datenbank in eine durch Komma getrennte ASCII-Datei (CSV) oder durch Tabulator getrennte Datei (TSV) exportieren. Die folgenden Datenbankfelder werden exportiert.
Die erste Zeile der exportierten Datei enthält die Spaltenbezeichnungen für die Felddaten. Jede zusätzliche Zeile enthält Felddaten für einen Remote Console Switch oder Server. Die Datei enthält eine Zeile für jeden Remote Console Switch und Server, der in der lokalen Datenbank definiert ist. So exportieren Sie eine Datenbank: 1 Wählen Sie im RCS Explorer-Menü Datei – Datenbank – Exportieren aus. Das Dialogfeld Datenbank exportieren wird angezeigt.
4 Verwenden des Viewers Über den Viewer können Sie eine Verbindung zu einem Server im Remote Console Switch-System herstellen. Mit dem Viewer verfügen Sie über die vollständige Steuerung von Tastatur, Monitor und Maus eines Servers. Sie können auch eine von Ihnen angelegte Serverliste scannen, indem Sie in der Anzeige der Miniaturansichten einzelne Server aktivieren.
Abbildung 4.1: RCS-Software – Register „Server“ So greifen Sie auf einen Server zu: 1 Klicken Sie im Explorer auf das Register Server. 2 Wählen Sie im Fenster Einheitenauswahl einen Server aus. 3 Klicken Sie auf die Taskschaltfläche Video verbinden. – oder – Klicken Sie mit der rechten Maustaste auf den Server. Ein Popup-Menü wird angezeigt. Wählen Sie Video verbinden aus. – oder – Doppelklicken Sie auf den Servernamen. – oder – Drücken Sie die .
1 Klicken Sie auf das Register Server und positionieren Sie den Cursor im Suchfeld. 2 Geben Sie den zu suchenden Text ein. Dabei kann es sich um den Servernamen oder um Informationen handeln, die Sie in den anderen Kopfzeilen der Liste Einheitenauswahl eingegeben haben, wie z. B. Typ oder Aufstellungsort. 3 Klicken Sie auf die Schaltfläche Suchen. Die Suchergebnisse werden in der Liste Einheit angezeigt. 4 Überprüfen Sie die Ergebnisse Ihrer Suche.
Merkmale des Viewer-Fensters Abbildung 4.2: Viewer-Fenster 1 Menüleiste: Zugriff auf viele Funktionen des Viewers. 2 Server-Desktop, auf den zugegriffen wird: Durch dieses Fenster interagieren Sie mit dem Server.
Viewer-Menüleiste Abbildung 4.3: Viewer-Menüleiste 1 Pin: Klicken Sie auf den Pin, um die Menüleiste in Position zu halten. Dadurch wird gewährleistet, dass die Menüleiste nicht ausgeblendet wird, wenn Sie den Mauszeiger von der Menüleiste weg bewegen. 2 Menüoptionen: Die Menüs bieten Zugriff auf Funktionen, die im Viewer zur Verfügung stehen. 3 Schaltflächen der Symbolleiste: Sie können der Symbolleiste bis zu zehn Schaltflächen hinzufügen.
Verbindungsstatusanzeige Teilungs-Modus Aktive Verbindung (normale, nicht exklusive Sitzung, ohne Teilen) Aktives Teilen (Primärbenutzer) Aktives Teilen (Sekundärbenutzer) Passives Teilen Tarnmodus Scan-Modus 5 Smart Card-Statusanzeige: Der Smart Card-Status wird durch ein Smart Card-Symbol auf der äußerst rechten Seite der Video Viewer-Symbolleiste angezeigt. Tabelle 4.
Anpassen des Viewers Sie können die Viewer-Einstellungen an Ihre Anforderungen anpassen, einschließlich der Einstellungen für Bildschirmauflösung, Symbolleiste und Tastaturmakros. Anpassen der Viewer-Symbolleiste Sie können der Symbolleiste bis zu zehn Schaltflächen hinzufügen. Mithilfe dieser Schaltflächen wird der schnelle Zugriff auf die festgelegten Funktionen und Tastaturmakros ermöglicht.
Abbildung 4.4: Dialogfeld „Sitzungsoptionen“ – Register „Symbolleiste“ Einstellen der Zeitverzögerung für das Ausblenden der Symbolleiste Die Symbolleiste wird ausgeblendet, sobald Sie den Mauszeiger weg bewegen, es sei denn, die Pin-Schaltfläche wurde aktiviert. Sie können die Zeitdauer zwischen dem Bewegen des Mauszeigers und dem Ausblenden der Symbolleiste anpassen, indem Sie die Verzögerung für das Ausblenden der Symbolleiste festlegen.
Verwenden Sie die Schaltflächen Nach oben und Nach unten, um die Dauer in Sekunden zu erhöhen oder zu verringern, für die die Symbolleiste angezeigt werden soll, nachdem der Mauszeiger weg bewegt wurde. 4 Klicken Sie auf OK, um die vorgenommenen Änderungen zu übernehmen und zum Viewer-Hauptfenster zurückzukehren. Vergrößern und Aktualisieren des Viewer Standardmäßig werden drei Schaltflächen in der Viewer-Symbolleiste angezeigt, mit denen Sie die Viewer-Anzeige anpassen können.
Klicken Sie in der Viewer-Symbolleiste auf Lokalen Cursor ausrichten. Der lokale Cursor wird auf den Cursor des Remote-Servers ausgerichtet. So wechseln Sie in den Vollbildmodus: Klicken Sie in der oberen rechten Ecke im Viewer auf die Schaltfläche Maximieren. – oder – Wählen Sie im Viewer-Menü Ansicht – Vollbild aus. Das Desktop-Fenster wird ausgeblendet und nur der Server-Desktop, auf den gerade zugegriffen wird, ist sichtbar.
Wählen Sie in der Menüleiste Ansicht – Skalierung – Automatische Skalierung aus, damit die Bildschirmanzeige des Servers automatisch skaliert wird. – oder – Wählen Sie in der Menüleiste Ansicht – Skalierung – Vollbild aus. – oder – Wählen Sie eine Bildschirmauflösung aus dem Untermenü Manuelle Skalierung aus. Abbildung 4.6: Viewer-Skalierung Anpassen der Videoqualität Der Viewer erlaubt es Ihnen, Monitoranpassungen automatisch oder manuell vorzunehmen.
Anpassen der Farbtiefe HINWEIS: Der Befehl „Farben“ kann nur vom Primärbenutzer verwendet werden. Er steht anderen Benutzern, die im Teilungs-Modus an der Sitzung teilnehmen, nicht zur Verfügung. HINWEIS: Wenn die Option „Aktualisierung im Hintergrund“ im Dialogfeld „Sitzungsoptionen“ aktiviert ist, wird die Farbtiefe automatisch auf die optimale verfügbare Farbe eingestellt und kann nicht geändert werden.
3 Verwenden Sie den Schieberegler oder klicken Sie auf die Schaltfläche Minus (-) oder Plus (+), um die Parameter für jedes betätigte Symbol einzustellen. Die Einstellungen werden sofort im Viewer-Fenster sichtbar. 4 Wenn Sie den Vorgang beendet haben, klicken Sie auf Schließen, um das Dialogfeld Manuelle Monitoranpassung zu verlassen. Optionen des Dialogfelds „Manuelle Monitoranpassung“ Abbildung 4.
5 Kontrast 6 Helligkeit 7 Rauschschwelle 8 Prioritätsschwelle 9 Automatische Monitoranpassung 10 Bild aktualisieren 11 Schieberegler 12 Testbild 13 Hilfe 14 Systemmonitor 15 Schaltfläche „Schließen“ Minimieren der Farbverfälschungen von Remote-Videositzungen Beim Aufbau von Remote-Videositzungen können Pixel-Farbverfälschungen aufgrund bestimmter Netzwerkbedingungen auftreten. Dieses Problem tritt meistens bei deckenden Hintergrundfarben auf.
HINWEIS: Die Absenkung der Rauschschwelle auf Null verursacht eine konstante Bildaktualisierung, starke Netzwerkauslastung und ein flackerndes Bild. Dell empfiehlt, die Rauschschwelle auf den höchsten Wert einzustellen, mit dem eine effiziente Systemleistung erreicht und gleichzeitig die Pixelfarben des Mauszeigerpfads wiederhergestellt werden können.
Abbildung 4.8: Viewer-Dialogfeld „Sitzungsoptionen für Maus“ Einstellen der Maus-Skalierung Sie können zwischen drei voreingestellten Optionen für die Maus-Skalierung wählen oder Ihre eigene Skalierung einrichten. Die drei Voreinstellungen sind: Standard(1:1), Hoch (2:1) oder Niedrig (1:2). Bei einem Skalierverhältnis von 1:1 sendet jede Mausbewegung auf dem Desktop-Fenster die gleiche Mausbewegung an den Server. Bei einer Skalierung von 2:1 sendet die gleiche Mausbewegung eine zweifache Mausbewegung.
4 Geben Sie die Werte für die Maus-Skalierung in die Felder X und Y ein. Jede Mausbewegung wird mit den entsprechenden X- und YSkalierungsfaktoren multipliziert. Der zulässige Eingabebereich liegt zwischen 0,25 und 3,00. Minimieren des Mausspureffekts Wenn sich der Mauszeiger während einer Remote-Videositzung über den Bildschirm bewegt, behalten einige Pixel eine Farbverfälschung bei.
Verbessern der Mausleistung Wenn Sie während einer Remote-Videositzung langsame Mausreaktionen feststellen oder die Mauszeiger nicht mehr synchronisiert sind, sollten Sie die Mausbeschleunigung im Betriebssystem des Zielservers deaktivieren. Microsoft Windows: 1 Deaktivieren Sie die Mausbeschleunigung. 2 Stellen Sie die Mausgeschwindigkeit so ein, dass sich der Schieberegler genau in der Mitte befindet.
4 Starten Sie die RCS Software neu. Anzeigen von mehreren Servern über den Scan-Modus Mit dem Viewer können Sie mehrere Server gleichzeitig in den Miniaturansichten des Scan-Modus anzeigen. Diese Ansicht enthält eine Reihe von Miniaturansichten, die kleine, skalierte, nicht interaktive Versionen der Bildschirmanzeige eines Servers darstellen. Unter jeder Miniaturansicht werden der Servername sowie eine Statusanzeige angezeigt.
Abbildung 4.9: Viewer – Miniaturansichten Der Scan-Modus besitzt eine niedrigere Priorität als eine aktive Verbindung. Wenn eine interaktive Sitzung mit einem Server besteht, wird dieser Server in der Scan-Sequenz übergangen und der Scan-Modus geht zum nächsten Server über. Es wird keine Fehlermeldung beim Anmelden angezeigt. Nach Beendigung der interaktiven Sitzung wird die Miniaturansicht wieder in die Scan-Sequenz aufgenommen.
Zugriff auf den Scan-Modus über die RCS-Software Abbildung 4.10: RCS-Software – Scannen der Server So greifen Sie in der RCS-Software auf den Scan-Modus zu: 1 Wählen Sie im Explorer das Register Remote Console Switches, Server, Standorte oder Verzeichnisse aus. 2 Wählen Sie im Fenster Einheitenauswahl mindestens zwei Server durch Drücken der Umschalttaste aus. – oder – Drücken Sie die -Taste. Die Taskschaltfläche für den ScanModus wird angezeigt.
Statusanzeige der Miniaturansichten Die grüne LED zeigt an, dass ein Server momentan gescannt wird. Das rote X bedeutet, dass der letzte Scan des Servers nicht erfolgreich war. Das heißt, dass der Scan aufgrund von Zugriffsrechten oder Pfadfehlern (der Serverpfad auf dem Remote Console Switch war nicht verfügbar) oder aus anderen Gründen nicht durchgeführt werden konnte. Wenn Sie den Mauszeiger über dem roten X platzieren, wird eine QuickInfo angezeigt, die den Grund für den Fehler angibt.
– oder – Klicken Sie mit der rechten Maustaste auf eine Server-Miniaturansicht und wählen Sie Interaktive Sitzung anzeigen aus. Der Server-Bildschirm wird in einem interaktiven Viewer-Fenster gestartet. So aktivieren oder deaktivieren Sie einen Server in der Scan-Sequenz: 1 Wählen Sie eine Server-Miniaturansicht aus. 2 Wählen Sie in der Anzeige der Miniaturansichten Miniaturansicht – [Servername] – Aktivieren.
Senden von Tastenanschläge über Makros an den Server Mit dem Viewer-Menü „Makros“ können auf einfache Weise mehrere Tastenanschläge an den Server gesendet werden. Der Viewer stellt eine Liste mit einer Auswahl von verfügbaren Tastenanschlägen für Microsoft Windows-, Sunund Linux-Systeme zur Verfügung. So wählen Sie das verwendete System aus: Klicken Sie im Viewer auf das Menü Makros. Klicken Sie auf Im Menü anzeigen und wählen Sie entweder Windows, Sun oder Linux aus.
Abbildung 4.12: Erweitertes Viewer-Menü „Makros“ – Option „Sun“ Abbildung 4.
Sitzungsoptionen – Register „Allgemein“ Über das Register Allgemein im Dialogfeld „Sitzungsoptionen“ steuern Sie die Option Tastaturanschlag-Weitergabe, wenn Sie sich nicht im Vollbildmodus befinden, die Tastaturanschlag-Menüaktivierung sowie die Aktualisierung im Hintergrund. Durch Aktivieren oder Deaktivieren des Kontrollkästchens TastaturanschlagWeitergabe können Sie bestimmen, ob der Modus Tastaturanschlag-Weitergabe aktiv ist. Standardmäßig ist die Option Tastaturanschlag-Weitergabe nicht aktiviert.
Option ausgewählt ist, wird ein konstanter Datenfluss vom Gerät zum Viewer gesendet, unabhängig davon, ob Änderungen auf dem Gerät vorgenommen wurden oder nicht. So ändern Sie Sitzungsoptionen: 1 Wählen Sie im Menü Extras im Viewer den Befehl Sitzungsoptionen. Die Symbolleiste „Sitzungsoptionen“ wird angezeigt. 2 Klicken Sie auf das Register Allgemein. 3 Ändern Sie die Sitzungsoptionen wie gewünscht. 4 Klicken Sie auf OK.
HINWEIS: Für Dell 1081AD- und 2161AD-Switches ist zur Unterstützung der Teilung von Sitzungen der optionale Dell Remote Access Key erforderlich. Die Teilung von Sitzungen kann vom Administrator und von anderen Benutzern mit den Rechten eines Einheitenadministrators oder Benutzeradministrators konfiguriert werden. Der erste Benutzer einer KVM-Sitzung mit einem Zielgerät wird als Primärbenutzer bezeichnet.
gleichzeitig. Nur der Primärbenutzer kann Trennanforderungen für alle Benutzer, die eine Verbindung teilen, annehmen oder zurückweisen. Der Primärbenutzer verfügt außerdem über die Steuerungsmöglichkeiten für Videoparameter und die Bildschirmauflösung der Videositzung. Sekundärbenutzer können entweder „aktive Benutzer“ sein, d. h., sie können Maus- und Tastaturdaten eingeben, oder „passive Benutzer“, die keine Mausund Tastaturdaten eingeben können.
• Wählen Sie in der Einheitenliste einen Remote Console Switch aus und drücken Sie die Eingabetaste. 3 Wählen Sie die Unterkategorie Global – Sitzungen aus. 4 Aktivieren Sie im Bereich Verbindung teilen das Kontrollkästchen TeilungsModus aktivieren. 5 Sie können die Option Automatisches Teilen aktivieren. Dies ermöglicht es Sekundärbenutzern, eine KVM-Sitzung automatisch zu teilen, ohne erst die Berechtigung vom Primärbenutzer anzufordern.
• Klicken Sie auf OK oder Ja. Wenn die Option „Automatisches Teilen“ nicht aktiviert wurde, wird der Primärbenutzer in einer Meldung über die Teilungsanfrage informiert. Er kann dann die Teilungsanfrage entweder als aktive oder als passive (schreibgeschützte) Sitzung akzeptieren oder die Teilungsanfrage ganz ablehnen. • Klicken Sie auf Nein, um die Teilungsanfrage abzubrechen.
HINWEIS: Nur der Primärbenutzer kann eine Exklusivsitzung anfordern. Nehmen weitere Benutzer an der Sitzung teil, wenn der Exklusivmodus angefordert wird, werden sie unabhängig von der Zugriffsebene des Primärbenutzers getrennt. So aktivieren Sie exklusive KVM-Sitzungen auf einem Switch: 1 Klicken Sie im Explorer auf das Register Geräte. 2 Führen Sie einen der folgenden Schritte aus: • Doppelklicken Sie in der Einheitenliste auf einen Remote Console Switch.
3 Wenn die KVM-Sitzung momentan geteilt wird, kann nur der Primärbenutzer sie als exklusiv zuweisen. Der Primärbenutzer wird in einer Meldung darüber informiert, dass Sekundärsitzungen beim Aufrufen einer exklusiven Sitzung beendet werden. Führen Sie einen der folgenden Schritte aus: • Klicken Sie auf Ja, um die Sitzungen der Sekundärbenutzer zu beenden. • Klicken Sie auf Nein, um die Aktion des Exklusivmodus abzubrechen. Sekundärbenutzer können die exklusive KVM-Sitzung nicht teilen.
4 Aktivieren Sie im Bereich Verbindung teilen das Kontrollkästchen Getarnte Verbindungen. Führen Sie folgende Schritte durch, um ein Zielgerät im Tarnmodus zu überwachen: 1 Klicken Sie im Explorer auf das Register Geräte. 2 Führen Sie einen der folgenden Schritte aus: 3 • Doppelklicken Sie in der Einheitenliste auf das Zielgerät. • Wählen Sie das Zielgerät aus und klicken Sie dann auf die Schaltfläche Video verbinden. • Klicken Sie mit der rechten Maustaste auf das Zielgerät.
• Der Switch, mit dem das Zielgerät verbunden ist, wurde nicht für getarnte Verbindungen konfiguriert. • Sie verfügen nicht über die erforderlichen Zugriffsrechte (Berechtigungen für getarnte Verbindungen folgen Berechtigungen zum Trennen von Verbindungen). • Der mit dem Zielgerät verbundene Switch ist kein Remote Console Switch.
Aktueller Benutzer Trennung durch Trennung kann zurückgewiesen werden Remote Console SwitchAdministrator Remote Console SwitchAdministrator Ja Remote-Administrator Lokaler Benutzer Nein Remote-Administrator Remote-Administrator Ja Remote-Administrator Remote Console SwitchAdministrator Nein Lokaler Benutzer Remote-Administrator Ja Lokaler Benutzer Remote Console SwitchAdministrator Ja Trennen einer Remote-Benutzer-Verbindung durch einen RemoteAdministrator Wenn ein Remote-Administrator
Trennung der Verbindung eines lokalen Benutzers/Remote-Administrators durch einen Remote-Administrator Wenn ein Administrator versucht, auf einen Server zuzugreifen, der von einem lokalen Benutzer oder einem anderen Remote-Administrator mit gleichen Berechtigungen verwendet wird, kann der aktuelle Benutzer die Trennanforderung annehmen oder ablehnen. Der verbundene lokale Benutzer oder RemoteAdministrator wird in einer Nachricht gefragt, ob er die Trennanforderung annehmen möchte.
Wenn die Verbindungsteilung für diesen Switch aktiviert wurde, können Sie die Sitzung teilen. Weitere Informationen zur Verbindungsteilung finden Sie unter „Trennungsmodus“. Je nach Ihren Zugriffsrechten (verglichen mit denen des Primärbenutzers) werden Sie aufgefordert, die vorhandene Sitzung zu teilen oder zu trennen. 3 Wenn die Option verfügbar ist, wählen Sie Unterbrechen aus. 4 Führen Sie einen der folgenden Schritte aus: 5 • Klicken Sie auf OK oder Ja.
Jeder Benutzer, der an einer KVM-Sitzung teilnimmt, kann auf alle Speichergeräte zugreifen, die diesem Zielgerät zugeordnet sind. Um dem Sicherheitsrisiko nicht autorisierter Benutzerzugriffe vorzubeugen, können Sie eine Virtual Media-Sitzung für eine KVM-Sitzung reservieren. Um das Speichermedium in einem Virtual Media-Gerät zu wechseln, müssen Sie zunächst die Zuordnung des Virtual Media-Geräts aufheben. Dann können Sie das neue Speichermedium einlegen und das Virtual Media-Gerät erneut zuordnen.
• Eine 1082DS-Einheit unterstützt bis zu drei gleichzeitig ausgeführte Virtual Media-Sitzungen (einschließlich lokaler und Remote-Sitzungen). Eine G2162DS-Einheit unterstützt bis zu vier gleichzeitig ausgeführte Virtual Media-Sitzungen (einschließlich lokale und Remote-Sitzungen). Eine 4322DS-Einheit unterstützt bis zu sechs gleichzeitig ausgeführte Virtual Media-Sitzungen (einschließlich lokaler und Remote-Sitzungen). Es kann immer jeweils nur eine Virtual Media-Sitzung auf dem Zielgerät aktiv sein.
Starten von Virtual Media Virtual Media wird von der Einheit mithilfe des Viewers per Remote-Zugriff gestartet. Der Viewer kann über die integrierte Weboberfläche oder über die RCS Software aufgerufen werden. Mit dem Virtual Media Client kann der Benutzer dem virtuellen Laufwerk auf dem Zielserver ein lokales Laufwerk zuordnen. So starten Sie Virtual Media über die RCS Software: 1 Starten Sie den Viewer über die Software. (Weitere Informationen finden Sie unter „Verwenden des Viewers“ auf Seite 67.
a. Aktivieren Sie im Dialogfeld „Virtual Media“ das Kontrollkästchen Zugeordnet neben den Laufwerken, die Sie zuordnen möchten. b. Wenn für das zugeordnete Laufwerk ein schreibgeschützter Zugriff festgelegt werden soll, aktivieren Sie das Kontrollkästchen Schreibgeschützt neben dem Laufwerk, bevor Sie es zuordnen.
Wenn Sie zu viele Laufwerke (ein DVD-Laufwerk und ein Massenspeichergerät) oder zu viele Laufwerke eines bestimmten Typs (mehrere DVD-Laufwerke oder Massenspeichergeräte) zuordnen, wird eine Warnmeldung angezeigt. Wenn Sie trotzdem ein neues Laufwerk zuordnen möchten, müssen Sie zuerst die Zuordnung eines vorhandenen Laufwerks aufheben. Danach können Sie das neue Laufwerk zuordnen. Nach der Zuordnung eines physischen Laufwerks oder Images kann es auf dem Zielgerät verwendet werden.
Virtual Media-Sitzungen Eine Virtual Media-Sitzung findet statt, wenn zwei USB-Verbindungen über ein einziges Kabel hergestellt werden. Diese Verbindungen werden vom Rechner als ein USB-CD/DVD-Laufwerk oder ein USB-Massenspeichergerät erkannt. Die Einstellungen einer Virtual Media-Sitzung lauten „Gesperrt“, „Zugriff auf zugeordnetes Laufwerk“ und „Verschlüsselungsebene“. • Gesperrt: Eine Virtual Media-Sitzung, die für eine bestimmte KVM-Sitzung reserviert ist.
Reservieren einer Virtual Media-Sitzung Eine Virtual Media-Sitzung kann auch reserviert werden, so dass nur ein spezieller Benutzer oder Administrator auf die Sitzung zugreifen oder diese schließen kann. Wenn Sie eine Virtual Media-Sitzung weiterführen möchten, nachdem die KVM-Sitzung beendet wurde, können Sie die Virtual MediaSitzung reservieren. Wenn die Virtual Media-Sitzung reserviert wurde, bleibt sie aktiv, auch wenn die zugehörige KVM-Sitzung beendet wird.
Virtual Media- und USB2-Beschränkungen Die Virtual Media-Funktion des Remote Console Switches ermöglicht es Ihnen, diese mit dem USB-Port einer angeschlossenen Einheit zu verbinden. Dank dieser Funktion kann ein Benutzer, der mit dem Switch arbeitet oder die RCS Software verwendet, von einem angeschlossenen Computer auf ein lokales USBSpeichergerät zugreifen, wie z. B. ein USB CD-/DVD-ROM-, Disketten- oder Flashlaufwerk.
Ob der Computer von einem virtuellen USB-Gerät gestartet werden kann, hängt vom Zielgerät ab, das das Starten von einem externen USB-Verbundgerät unterstützen muss. Eine CD/DVD des Betriebssystems, das das Starten von einem externen USB 2.0-Gerät unterstützt, ist ebenfalls erforderlich. Im Folgenden ist eine Teilliste von Betriebssystemen angegeben, die das Starten von einem externen USB 2.
• Einige BIOS-Versionen bieten eine Funktion zum Begrenzen der USBGeschwindigkeiten. Wenn diese Option verfügbar ist, stellen Sie den USB-Port auf den Modus „USB 1.1“ oder „Vollgeschwindigkeit“ ein und führen Sie einen Neustart durch. • Setzen Sie eine USB 1.1-Karte ein und führen Sie einen Neustart durch. • Installieren Sie einen USB 1.1-Hub zwischen dem USB2-Kabel und dem Zielgerät und führen Sie einen Neustart durch.
A Anhang A: Aktualisieren der RCS-Software Achten Sie darauf, dass Sie im Besitz der neuesten RCS Software-Version sind (erhältlich über die Webseite von Dell unter: www.dell.com/support), damit ein optimaler Betrieb Ihres Systems gewährleistet wird. So aktualisieren Sie die RCS Software: 1 Laden Sie die Aktualisierungsdatei von der Dell Support-Website herunter: www.dell.com/support. 2 Doppelklicken Sie auf das Installationsprogramm.
4 Die Installation beginnt. Die Programmdateien, Verknüpfungen, Umgebungsvariablen und Registrierungseinträge (nur bei Win 32-Systemen) werden installiert bzw. durch die neuen Dateien und Einstellungen der aktuellen Version überschrieben. HINWEIS: Damit die Aktualisierungserkennung in Kraft tritt, muss zuerst ein Neustart durchgeführt werden, oder Sie müssen sich abmelden.
B Anhang B: Tastatur und Maus Tabelle B.1: Tastatur- und Maus-Tastenkombinationen im Unterteilungsfenster Vorgang Beschreibung F6 Navigiert zwischen den geteilten Bildschirmen und markiert das letzte Element, auf dem sich der Eingabefokus befand. F8 Markiert die Unterteilung. Pfeil-nach-linksoder Pfeil-nachoben-Taste Verschiebt die Unterteilung nach links, sofern diese markiert ist. Pfeil-nachrechts- oder Pfeil-nachunten-Taste Verschiebt die Unterteilung nach rechts, sofern diese markiert ist.
Tabelle B.2: Tastatur- und Maus-Tastenkombinationen zur Steuerung in der Baumstrukturansicht Vorgang Beschreibung Einfacher Mausklick Hebt die bestehende Auswahl auf und wählt den Knoten aus, über dem sich der Mauszeiger befindet. Doppelter Mausklick Blendet einen erweiterbaren Knoten ein/aus (ein Knoten, der untergeordnete Objekte hat). Keine Aktivität bei einem untergeordneten Knoten (ein Knoten, der keine untergeordneten Objekte hat).
Vorgang Beschreibung Pfeil-nachunten-Taste Hebt die bestehende Auswahl auf und bewegt die Auswahl um eine Zeile nach unten. Bild auf Hebt die bestehende Auswahl auf, blättert eine Seite nach oben und wählt die erste Position auf der Seite aus. Bild ab Hebt die bestehende Auswahl auf, blättert eine Seite nach unten und wählt die letzte Position auf der Seite aus. Löschen Führt die Löschfunktion durch. Besitzt die gleiche Funktion wie die Menüfunktion Bearbeiten-Löschen.
Vorgang Beschreibung Umschalttaste + Mausklick Hebt eine bestehende Auswahl auf und wählt die Zeilen zwischen der aktuellen Markierung und der Zeile aus, in der sich der Mauszeiger befindet, wenn ein Mausklick durchgeführt wird. Kehrt den Auswahlstatus der Zeile um, in der sich der Mauszeiger Strg + Mausklick befindet, ohne dass der Auswahlstatus einer anderen Zeile beeinflusst wird. Doppelter Mausklick Startet die Standardaktion für die ausgewählte Einheit.
C Anhang C: TCP-Ports Die nachfolgende Tabelle zeigt die Funktionen des Remote Console Switch und der verwendeten Ports. Tabelle C.1: Verwendete Ports Port Funktion TCP 80/443 Standard-HTTP/HTTPS TCP 2068 Video Viewer-Video, Tastatur, Maus, Benutzerauthentifizierung und Virtual Media. TCP/UDP 3211 Verwaltung und Installation/Suche. HINWEIS: Die TCP/IP-Ports sind statisch und können nicht geändert werden.
Anhang C: TCP-Portsxxx | xxx122
D Anhang D: Technischer Kundendienst Unser technischer Kundendienst steht Ihnen jederzeit bei Fragen hinsichtlich Installations- oder Betriebsproblemen mit Ihrem Produkt von Dell zur Verfügung. Verfahren Sie wie folgt zur schnellstmöglichen Problemlösung. So verfahren Sie zur Problemlösung: 1 Sehen Sie im entsprechenden Abschnitt der Betriebsanleitung nach, ob das Problem mit den vorgeschlagenen Abhilfemaßnahmen gelöst werden kann. 2 Besuchen Sie unsere Website unter www.dell.
Anhang D: Technischer Kundendienstxxx | xxx124