Dell™ Remote Console Switch Benutzerhandbuch für die Software
Hinweise HINWEIS: Ein HINWEIS weist auf Informationen hin, die Ihnen helfen, Ihren Rechner effizienter einzusetzen. Zusätzliche Software: Sie erkennen an, dass das SOFTWAREPRODUKT urheberrechtlich geschützte Software von Dell-Zulieferfirmen enthalten oder einschließen kann, die in der beiliegenden Dokumentation bzw. in anderen gedruckten oder elektronischen Materialien beschrieben („Zusätzliche Software“) und mit einer entsprechenden Lizenz von diesen Zulieferfirmen zur Verfügung gestellt wird.
Inhalt Hinweise 2 Produktüberblick 7 Merkmale und Vorteile Umfassende Anpassungsfähigkeit Umfassende Remote Console Switch Verwaltungsfunktionen Authentifizierung und Autorisierung 7 8 8 9 Systemkomponenten RCS Explorer-Fenster Video Viewer Kompatibilität mit Avocent®-Produkten 9 9 10 10 Bedienfunktionen Benennen von Zielgeräten Zielgeräte-Namensanzeigen Sortieren IPv4- und IPv6-Netzwerkadressfunktionen Installation 11 11 12 12 13 15 Im Lieferumfang der Software enthalten 15 Unterstützte Betri
Starten der Software 19 Konfiguration von Switches und Zielgeräten 20 Installieren und Einrichten der Weboberfläche 23 Normalbetrieb der Software 25 Anzeigen des Systems im Explorer 25 Anpassen der Fensteranzeige 27 Hinzufügen eines Remote Console Switch (Dell oder Avocent) 28 Zugriff auf den Remote Console Switch 37 Starten des VNC- oder RDP-Viewers 40 Ändern von Server- und Switch-Eigenschaften Allgemeine Eigenschaften Eigenschaften des Servernetzwerks Eigenschaften des Switch-Netzwerks In
Zuordnen einer Einheit zu einem Standort, Aufstellungsort oder Verzeichnis Löschen und Umbenennen 58 59 Explorer-Fenster einstellen Ändern der beim Start ausgewählten Ansicht Ändern des Standard-Browsers 61 62 63 Verwalten lokaler Datenbanken Speichern einer Datenbank Laden einer Datenbank Exportieren einer Datenbank 63 63 64 65 Verwenden des Viewers Zugriff auf Server über die RCS Software 67 67 Interaktion mit dem angezeigten Server 69 Funktionen des Viewer-Fensters 70 Anpassen des Viewers 73 Anpa
Trennungsmodus Virtual Media Teilung und Unterbrechung Starten von Virtual Media Zuordnen von Virtual Media-Laufwerken Virtual Media-Verbindungsstatus Virtual Media-Sitzungen 101 104 105 106 107 109 109 Anhang A: Aktualisieren der RCS Software 115 Anhang B: Tastatur und Maus 117 Anhang C: TCP-Ports 121 Anhang D: Technischer Kundendienst 123 Inhaltxxx | xxx6
1 Produktüberblick Die Dell™ Remote Console Switch- (RCS-) Software ist eine plattformübergreifende Verwaltungsanwendung, mit der Switches und alle angeschlossenen Server überwacht und gesteuert werden können. Das plattformübergreifende Design stellt Kompatibilität mit den meisten gängigen Betriebssystemen und Hardware-Plattformen sicher. Die RCS Software sorgt für sichere Switch-basierte Authentifizierung, Datenübertragung und Speicherung von Benutzernamen/Kennwort.
Umfassende Anpassungsfähigkeit Die RCS Software kann auf Ihre spezifischen Systemanforderungen zugeschnitten werden. Nutzen Sie vordefinierte Gruppen oder erstellen Sie Ihre eigenen. Erstellen Sie benutzerorientierte Einheiten- und Feldbezeichnungen und Symbole für ein Höchstmaß an Flexibilität und Benutzerfreundlichkeit. Die Verwendung aussagekräftiger Namen erleichtert das Auffinden von Systemeinheiten.
HINWEIS: Für Dell 1081AD- und 2161AD-Switches ist der Dell Remote Access Key (RAK) erforderlich, damit die Switches über den RCS hinzugefügt und verwaltet werden können. Authentifizierung und Autorisierung Die RCS Software gewährt die entsprechenden Zugriffsberechtigungen, so dass mehrere Remote Console Switches über eine einzige Oberfläche verwaltet werden können, anstatt jeden Remote Console Switch einzeln verwalten zu müssen.
Über die Geräteliste im Explorer können Sie ein Gerät in der Liste der Zielgeräte auswählen und eine KVM-Sitzung mit dem Gerät starten. Durch Starten einer KVM-Sitzung (Keyboard, Video & Mouse –Tastatur, Video & Maus) wird ein Video Viewer geöffnet. Über die Liste im Explorer können Sie den zu konfigurierenden Switch auswählen. Video Viewer Benutzer können über den Video Viewer auf Zielgeräte zugreifen und diese Geräte verwalten.
• Serielle VT100-Module (Avocent-Module erhältlich) • True Serial-Module (Module von Dell und Avocent erhältlich) • Sun-Module (Avocent-Module erhältlich) • PS2M-Module (Avocent-Module erhältlich) HINWEIS: Dell SIP-Module werden an direkt verbundenen Avocent-Switches unterstützt. HINWEIS: True Serial-Module werden von den Dell 1081AD- und 2161AD-Switches nicht unterstützt.
Wenn Sie oder andere Benutzer keinen eindeutigen Namen angeben, wird in einer entsprechenden Meldung angezeigt, dass ein eindeutiger Name erforderlich ist. Zielgeräte-Namensanzeigen Beim Hinzufügen eines Switches werden die vom Switch abgerufenen Zielgerätenamen in der Softwaredatenbank gespeichert. Der Benutzer kann dann das Zielgerät im Explorer umbenennen. Der neue Name wird in der Datenbank gespeichert und in verschiedenen Komponentenfenstern verwendet.
Spaltenüberschrift einen Pfeil aufweist, können Sie die Liste in dieser Spalte in auf- oder absteigender Reihenfolge sortieren. Zum Sortieren einer Anzeige nach Spaltenüberschrift klicken Sie auf den dort angegebenen Pfeil. Die Elemente in der Liste werden entsprechend dieser Spalte sortiert. Ein nach oben zeigender Pfeil weist darauf hin, dass die Liste nach dieser Spaltenüberschrift in aufsteigender Reihenfolge sortiert wurde.
xxx | Produktüberblickxxx
2 Installation Stellen Sie vor der Installation der RCS Software auf einem Clientcomputer sicher, dass Sie über alle erforderlichen Komponenten verfügen und dass auf den Zielgeräten und RCS-Clientcomputern die unterstützten Betriebssysteme, Browser und Java Runtime Environment ausgeführt werden. Im Lieferumfang der Software enthalten Die Software wird mit den Einheiten auf einer Remote Console Switch Software-CD geliefert.
• SUSE® Linux Enterprise Server 10 und Server 11 • Ubuntu 8 Server und Workstation Auf den Zielgeräten muss eines der nachstehend aufgeführten Betriebssysteme ausgeführt werden: • Microsoft Windows 2000 Server (32 Bit) und Advanced Server • Microsoft Windows XP Professional und Standard mit Service Pack 3 • Microsoft Windows Server 2003 Web, Standard und Enterprise • Microsoft Windows Server 2008 Web, Standard und Enterprise • Microsoft Windows Vista Standard, Business mit Service Pack 1 und En
• Die Farbpalette muss mindestens 65.536 (16 Bit) Farben aufweisen Unterstützte Browser Auf Computern, die zum Zugriff auf die Weboberfläche verwendet werden, und Clientcomputern, auf denen die Software läuft, muss einer der folgenden Browser installiert sein: • Microsoft Internet Explorer ab Version 6.x SP1 • Firefox ab Version 2.
Installation unter Linux: 1 Legen Sie die RCS Software-CD-ROM in Ihr CD-ROM-Laufwerk ein. 2 Wenn AutoMount unterstützt wird und aktiviert ist, fahren Sie mit Schritt 3 fort. - oder Wenn Ihr System AutoMount nicht unterstützt: Mounten Sie den CD-ROM-Datenträger, indem Sie folgenden Befehl ausführen: mount -t iso9660 -ro mode=0555 Ersetzen Sie „Gerät“ durch den Namen der CD-ROM in Ihrem Rechner und „Mountpunkt“ durch den Namen des gewünschten Mountpunkts.
3 Klicken Sie auf die Schaltfläche Ändern/Entfernen. Der Deinstallationsassistent wird gestartet. 4 Klicken Sie auf Deinstallieren und folgen Sie den Anweisungen auf dem Bildschirm. Zum Deinstallieren der Software auf Microsoft Windows-Betriebssystemen mithilfe eines Befehlsfensters führen Sie die folgenden Schritte aus: 1 Öffnen Sie ein Befehlsfenster und wechseln Sie zum RCSInstallationsverzeichnis, das während der Installation verwendet wurde.
Wählen Sie Start – Programme – Dell RCS Software. Die RCS Software wird gestartet. So starten Sie die RCS Software unter Linux: Geben Sie im Anwendungsverzeichnis (standardmäßig: /usr/lib/Dell_Remote_ Console_Switch_Software) den folgenden Befehl ein: ./Dell_Remote_Console_Switch_Software - oder Geben Sie von (/user/bin) aus die folgende Verknüpfung ein: .
4 Konfigurieren Sie die Namen aller Zielgeräte mit der lokalen grafischen Benutzeroberfläche. 5 Wiederholen Sie die Schritte 3 bis 6 für jeden Switch, den Sie verwalten möchten. 6 Sobald eine Software-Umgebung eingerichtet wurde, wählen Sie Datei – Datenbank – Speichern aus, um eine Kopie der lokalen Datenbank mit allen Einstellungen zu speichern. 7 Auf einem zweiten Computer wählen Sie im Softwaremenü die Befehle Datei – Datenbank – Laden. Suchen Sie die Datei, die Sie gespeichert haben.
durchgeführt wird. Drücken Sie die Eingabetaste, um das Hauptmenü aufzurufen. So konfigurieren Sie die Remote Console Switch-Hardware: 1 Sie sehen das Hauptmenü mit elf Optionen. Wählen Sie Option 1 aus: Network Configuration. 2 Wählen Sie Option 1 aus, um die Netzwerkgeschwindigkeit einzustellen. Sobald Sie die Auswahl bestätigen, wird wieder das Menü Network Configuration angezeigt. 3 Wählen Sie Option 2 aus, um das Menü IP Configuration zu öffnen.
Mausbeschleunigung Wenn die Maus während einer Remote-Videositzung nur langsam reagiert, deaktivieren Sie die Mausbeschleunigung im Betriebssystem des Zielgeräts und stellen Sie die Mausbeschleunigung auf jedem Zielgerät auf Langsam oder Keine ein. Installieren und Einrichten der Weboberfläche Wenn Sie eine neue Einheit installiert haben, können Sie die Weboberfläche verwenden, um Einheitenparameter zu konfigurieren und Videositzungen zu starten.
3 Die Weboberfläche wird geöffnet und die Registerkarte Verbindungen wird angezeigt. HINWEIS: Zur Verwendung der Weboberfläche muss Java Runtime Environment (JRE) Version 1.6.0_11 oder höher auf Ihrem Computer installiert sein. Der KVM-Switch versucht, Java auf Ihrem PC zu finden. Falls Java nicht installiert ist, können Sie es unter folgender Adresse herunterladen http://www.java.com und dann die JNLP-Datei zu Java WebStart zuordnen.
3 Normalbetrieb der Software Der RCS Software-Explorer (im Folgenden als „Explorer“ bezeichnet) ist die Haupt-Benutzeroberfläche für die Software. Sie können alle unterstützten Einheiten anzeigen, abrufen, verwalten und benutzerdefinierte Gruppierungen erstellen. Anzeigen des Systems im Explorer Beim Starten der Software wird das Explorer-Hauptfenster geöffnet. Der Explorer ist in verschiedene Fenster unterteilt: Ansichtauswahl-Register, Gruppenauswahl-Fenster und Einheitenauswahl-Fenster.
Abbildung 3.1: Explorer-Fenster 1 Menüleiste: Ermöglicht den Zugriff auf viele Funktionen der RCS Software. 2 Ansichtauswahl-Register: Enthält vier Ansichtauswahl-Register zur Auswahl der Explorer-Ansicht. 3 Gruppenauswahl-Fenster: Enthält eine Baumstrukturanzeige und zeigt die Gruppen an, die im aktuellen Ansichtauswahl-Register verfügbar sind.
5 Einheitenauswahl-Fenster: Enthält die Suchleiste, die Einheitenliste sowie die entsprechenden Taskschaltflächen für die ausgewählte Ansicht oder Gruppe. 6 Suchleiste: Ermöglicht die Suche in der Datenbank nach Text, der in das Suchfeld eingegeben wird. 7 Einheitenliste: Zeigt eine Liste der Einheiten an, die in der aktuell ausgewählten Gruppe enthalten sind, oder die Ergebnisse der Suche, die über die Suchleiste ausgeführt wurde.
zu Verknüpfungen mit der Baumstrukturanzeige und -steuerung finden Sie unter „Tastatur und Maus“ auf Seite 117. Sie können angeben, welche Ansicht (Einheiten, Geräte, Standorte oder Verzeichnisse) beim Start angezeigt werden soll, oder Sie können diese vom Explorer festlegen lassen. Weitere Informationen finden Sie unter „Anpassen der Fensteranzeige“ auf Seite 27. Sie können die Anzeigereihenfolge in der Einheitenliste ändern, indem Sie in die Spaltenüberschrift klicken.
Klicken Sie auf die Taskschaltfläche Neuer Remote Console Switch. Der „Neuer Remote Console Switch“-Assistent wird angezeigt. 2 Klicken Sie auf Weiter, um fortzufahren. Das Dialogfeld Produkt-Typ wird angezeigt und Sie werden aufgefordert, das Remote Console Switch-Produkt und den entsprechenden Lieferanten auszuwählen. Abbildung 3.2: Dialogfeld „Produkt-Typ“ 3 Wählen Sie einen Lieferanten aus. Für jeden Lieferanten werden die unterstützten Produktnamen in der Liste Produkt aufgeführt.
Produkt aufgenommen und ist verfügbar, wenn Sie das nächste Mal einen Remote Console Switch hinzufügen. HINWEIS: In jedem Dialogfeld des „Neuer Remote Console Switch“-Assistenten wird der Switch-Typ angegeben, den Sie in der Produktliste ausgewählt haben. 4 Klicken Sie auf Weiter. 5 Sie werden aufgefordert, anzugeben, ob dem Remote Console Switch eine IP-Adresse zugewiesen ist oder nicht. Klicken Sie auf Ja und danach auf Weiter. 6 Das Fenster Produkt suchen wird angezeigt.
Abbildung 3.3: Dialogfeld „Gestufte Switches konfigurieren“ 10 Wenn Sie die letzte Seite des Remote Console Switch-Assistenten erreicht haben, klicken Sie auf Fertig stellen, um den Assistenten zu beenden und zum Hauptfenster zurückzukehren. Ihr Remote Console Switch sollte nun im Fenster Einheitenauswahl angezeigt werden. So fügen Sie einen neuen Remote Console Switch ohne zugewiesene IP-Adresse hinzu: 1 Wählen Sie Datei – Neu – Remote Console Switch aus dem ExplorerMenü.
2 Klicken Sie auf Weiter, um fortzufahren. Das Dialogfeld Produkt-Typ wird angezeigt und Sie werden aufgefordert, das Remote Console Switch-Produkt und den entsprechenden Lieferanten auszuwählen. Abbildung 3.4: Dialogfeld „Produkt-Typ“ 3 Wählen Sie einen Lieferanten aus. Für jeden Lieferanten werden die unterstützten Produktnamen in der Liste Produkt aufgeführt. Wählen Sie ein Produkt aus.
5 Sie werden aufgefordert, anzugeben, ob dem Remote Console Switch eine IP-Adresse zugewiesen ist. Klicken Sie auf Nein und danach auf Weiter. 6 Das Fenster Netzwerkadresse wird angezeigt. Geben Sie IP-Adresse, Subnetzmaske (bei Verwendung des IPv4-Modus) oder Präfixlänge (bei Verwendung des IPv6-Modus) sowie Gateway ein, die Sie der Einheit zuweisen möchten, und klicken Sie auf Weiter. IPv4-Adressen werden durch Punkte getrennt eingegeben (xxx.xxx.xxx.xxx.xxx).
b. Ordnen Sie jedem SIP oder Avocent IQ-Modul, das mit einem Switch verbunden ist, den entsprechenden Switch aus den Dropdown-Listen zu. Abbildung 3.5: Dialogfeld „Gestufte Switches konfigurieren“ 10 Klicken Sie auf Fertig stellen, wenn Sie diesen Assistenten beenden und zum Hauptfenster zurückkehren möchten. Ihr Remote Console Switch sollte nun im Fenster Einheitenauswahl angezeigt werden. So suchen Sie nach einem Remote Console Switch: 1 Wählen Sie im Explorer-Menü der Software Extras - Suchen aus.
Wenn Sie den IPv4-Modus verwenden, wählen Sie IPv4-Adressbereich verwenden aus und geben Sie in den Feldern Von Adresse und Bis Adresse den Bereich der IP-Adressen ein, den Sie im Netzwerk durchsuchen möchten. IPv4-Adressen werden durch Punkte getrennt eingegeben (xxx.xxx.xxx.xxx.xxx). - oder Wenn Sie den IPv6-Modus verwenden, wählen Sie IPv6-Adressbereich verwenden aus und geben Sie in den Feldern Von Adresse und Bis Adresse den Bereich der IP-Adressen ein, den Sie im Netzwerk durchsuchen möchten.
5 Klicken Sie auf die hinzuzufügenden Remote Console Switches und dann auf die Schaltfläche Hinzufügen (>), um die Auswahl in die Liste Remote Console Switches hinzufügen zu verschieben. Abbildung 3.6: Dialogfeld „Remote Console Switches auswählen“ 6 Wiederholen Sie Schritt 5 für alle Remote Console Switches, die hinzugefügt werden sollen. Klicken Sie auf Weiter, um fortzufahren.
8 Wenn mindestens ein Switch aus irgendwelchen Gründen nicht der lokalen Datenbank hinzugefügt werden konnte (einschließlich, wenn Sie während des Hinzufügens auf Stopp geklickt haben), wird die Seite Nicht alle Remote Console Switches hinzugefügt des Such-Assistenten angezeigt. Auf dieser Seite werden alle ausgewählten Switches und ihr Status aufgelistet. Der Status gibt an, ob ein Remote Console Switch der lokalen Datenbank hinzugefügt wurde und wenn nicht, warum der Vorgang fehlgeschlagen ist.
Abbildung 3.7: Register für Anzeige des Remote Console Switch ausgewählt So melden Sie sich bei einem Remote Console Switch an: 1 Klicken Sie im Explorer auf das Register Remote Console Switches. 2 Doppelklicken Sie im Fenster Einheitenauswahl auf einen Remote Console Switch. - oder Wählen Sie einen Remote Console Switch im Fenster Einheitenauswahl aus und klicken Sie auf die Taskschaltfläche Remote Console Switch konfigurieren.
Klicken Sie auf einen Remote Console Switch im Fenster Einheitenauswahl und drücken Sie die Eingabetaste. 3 Falls verfügbar werden die im Cache gespeicherten Anmeldeberechtigungen verwendet. Falls nicht, wird eine Anmeldungsaufforderung angezeigt. Geben Sie Benutzername und Kennwort ein.
Starten des VNC- oder RDP-Viewers Die RCS Software unterstützt benutzerdefinierte VNC-Viewer (Virtual Network Computing) und RDP-Viewer (Remote Desktop Protocol). Wählen Sie zum Starten des VNC- oder des RDP-Viewers die Registerkarte Server im RCS Software-Explorer aus. Wählen Sie einen Server aus der Einheitenliste aus. Klicken Sie dann entweder auf die Schaltfläche VNC oder auf RDP rechts unten auf dem Bildschirm.
- oder Klicken Sie mit der rechten Maustaste auf die Einheit und wählen Sie Eigenschaften aus. Das Dialogfeld Eigenschaften wird angezeigt. Abbildung 3.8: Register „Allgemeine Eigenschaften“ für einen Server 3 Geben Sie den Namen der Einheit ein. Eine doppelte Namensvergabe ist nicht zulässig. 4 (Nur für Server –optional) Wählen Sie den Servertyp aus. Wenn Ihre Auswahl nicht in der Dropdown-Liste angezeigt wird, geben Sie den Namen für den neuen Servertyp in das Textfeld ein.
6 (Optional) Weisen Sie eine Einheit einem Standort, einer Abteilung oder einem Aufstellungsort zu. Wenn eine Option in der Dropdown-Liste nicht verfügbar ist, geben Sie den Namen der neuen Zuordnung in das Textfeld ein. Sobald Sie die Eingabe abgeschlossen haben, ist diese Option in der Dropdown-Liste für zukünftige Zuordnungen verfügbar. 7 Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern.
die Schaltfläche Browser angezeigt, mit der Sie den Browser an der angegebenen URL starten können. 4 Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern. - oder Klicken Sie auf OK, um die Einstellungen zu speichern und das Fenster zu schließen. - oder Klicken Sie auf Abbrechen, um den Vorgang zu beenden, ohne die neuen Einstellungen zu speichern.
HINWEIS: Dell 1081AD- und 2161AD-Switches unterstützen IPv4- und IPv6-Modi nicht gleichzeitg. 4 Geben Sie die HTTP- und die HTTPS-Portnummern im Feld HTTP-Port bzw. HTTPS-Port ein, wenn Sie die Portnummern für den Remote Console Switch in der seriellen Konsole geändert haben. Weitere Informationen zum Ändern der Portnummern in der seriellen Konsole finden Sie unter „HTTP/HTTPS-Optionen“ auf Seite 26. 5 Klicken Sie auf Übernehmen, um die neuen Einstellungen zu speichern.
3 4 (Optional) Klicken Sie auf das Register Informationen und geben Sie eine Beschreibung der Einheit ein. In den folgenden Feldern können Sie beliebige Informationen eingeben. a. Im Feld Beschreibung können 0 bis 128 Zeichen eingegeben werden. b. Im Feld Kontakt können 0 bis 128 Zeichen eingegeben werden. c. Im Feld Kontakt-Telefonnummer können 0 bis 64 Zeichen eingegeben werden. d. Im Feld Kommentare können 0 bis 256 Zeichen eingegeben werden.
3 Klicken Sie auf das Register Verbindungen, um die Verbindungen des Servers anzuzeigen. Verbindungseigenschaften sind schreibgeschützt und nur für Server verfügbar. Es wird der Verbindungspfad angezeigt, der für den Zugriff auf dieses Gerät verwendet wird, sowie der Verbindungstyp, z. B. Video. 4 Wenn der Vorgang abgeschlossen ist, klicken Sie auf OK oder Abbrechen, um das Fenster zu schließen.
Leerzeichen sind nicht zulässig. Eine doppelte Adressvergabe ist zulässig. Sie können IPv4- und IPv6-Adressen verwenden. 5 Geben Sie im Feld „Port“ eine Portnummer zwischen 23 und 65535 ein. Wenn dieses Feld leer ist, wird Port 23 verwendet. 6 Aktivieren Sie das Kontrollkästchen Standard verwenden, indem Sie es markieren, oder heben Sie die Markierung auf, um es zu deaktivieren. Wenn diese Einstellung aktiviert ist, wird die unter Optionen angegebene globale Standardeinstellung verwendet.
Windows, Linux und UNIX®, kann die RDP-Anwendung in einem Befehlsfenster des Betriebssystems gestartet werden. So ändern Sie RDP-Eigenschaften: 1 Wählen Sie in der Einheitenliste einen Server aus. 2 Wählen Sie im Explorer-Menü Ansicht – Eigenschaften aus. - oder Klicken Sie auf die Taskschaltfläche Eigenschaften. - oder Klicken Sie mit der rechten Maustaste auf die Einheit. Wählen Sie im Popup-Menü die Option Eigenschaften aus. Das Dialogfeld Eigenschaften wird angezeigt.
8 Geben Sie im Feld unter dem Pfad und dem Namen Befehlszeilenargumente ein. - oder Klicken Sie zum Einfügen eines vordefinierten Makros an der Cursorposition in der Befehlszeile auf das Listenfeld Makro einfügen und wählen Sie ein Makro aus dem Dropdown-Menü aus. Bei der Ausführung der Anwendung ersetzt die RCS Software diese Variablen automatisch. 9 Aktivieren/deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster.
Das von Ihnen angegebene Netzwerk wird in einem Browser-Fenster geöffnet. Ändern von Server- und Switch-Optionen In der RCS Software können Sie im Dialogfeld Optionen individuelle Serveroder Switch-Optionen, einschließlich Allgemein, HTTP-/HTTPS-Ports, VNC und RDP, ändern. Allgemeine Optionen So ändern Sie eine benutzerdefinierte Feldbezeichnung: 1 Wählen Sie im Explorer-Menü Extras – Optionen aus. Das Dialogfeld Optionen wird angezeigt. Abbildung 3.
3 Geben Sie die Feldbezeichnung in Singular- und Pluralform ein. Die Länge muss zwischen 1 und 32 Zeichen liegen. Das Feld darf nicht leer bleiben. Leerzeichen in der Mitte sind zulässig, Leerzeichen am Beginn und am Ende des Namens jedoch nicht. 4 Klicken Sie auf OK, um die neue Feldbezeichnung zu speichern. - oder Klicken Sie auf Abbrechen, um das Dialogfeld zu verlassen, ohne die Änderungen zu speichern.
• Klicken Sie auf OK, um die neuen Einstellungen zu speichern. • Klicken Sie auf Abbrechen, um den Vorgang zu beenden, ohne die neuen Einstellungen zu speichern. Deaktivieren der DirectDraw-Unterstützung (nur WindowsBetriebssysteme) Die Software unterstützt DirectDraw. Hierbei handelt es sich um einen Standard, der die direkte Manipulation von Videoanzeigespeicher, HardwareOverlays und Page-Flipping ohne Eingriff der Grafikschnittstelle (Graphical Device Interface, GDI) ermöglicht.
1 Wählen Sie im Explorer-Menü Extras – Optionen aus. Das Dialogfeld Optionen wird angezeigt. 2 Klicken Sie auf das Register HTTP-/HTTPS-Ports. 3 Geben Sie die neuen HTTP- und HTTPS-Standard-Portnummern ein. 4 Klicken Sie auf OK. VNC-Optionen Die Software unterstützt benutzerdefinierte VNC-Viewer über die Eigenschaftenseite. Im Register „VNC“ können Sie nach einer benutzerdefinierten VNC-Anwendung suchen und deren Befehlszeilenargumente einschließen.
Ausführung der Anwendung ersetzt die RCS Software diese Variablen automatisch. 5 Aktivieren/deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster. Wenn es aktiviert ist, wird die benutzerdefinierte VNC-Anwendung in einem Befehlsfenster des Betriebssystems gestartet. 6 Klicken Sie auf OK. RDP-Optionen Die Software unterstützt einen benutzerdefinierten RDP-Viewer über die Eigenschaftenseite.
Ausführung der Anwendung ersetzt die RCS Software diese Variablen automatisch. 5 Aktivieren/deaktivieren Sie das Kontrollkästchen Start im Befehlsfenster. Wenn es aktiviert ist, wird die benutzerdefinierte RDP-Anwendung in einem Befehlsfenster des Betriebssystems gestartet. 6 Klicken Sie auf OK. Organisieren des Systems Mit den Ansichtregistern „Standorte“ und „Verzeichnisse“ in der RCS Software können Sie Ihre Remote Console Switches und Server in benutzerdefinierten Gruppen organisieren und verwalten.
Abbildung 3.10: Ausgewähltes Register „Standorte“ Benutzerdefinierte Feldbezeichnungen ändern Mit benutzerdefinierten Feldbezeichnungen können Sie die Namen der Spaltenüberschriften Standort, Abteilung und Aufstellungsort ändern, die in den Fenstern Gruppen und Einheitenauswahl in der Software angezeigt werden. Auf diese Weise lassen sich die Remote Console Switches und Server nach Ihren Vorstellungen gruppieren. Das Feld Abteilung ist ein Unterfeld von Standort.
Abbildung 3.11: Beispiel für geänderte benutzerdefinierte Felder So erstellen Sie einen neuen Standort, eine neue Abteilung oder einen neuen Aufstellungsort: 1 Wählen Sie im Explorer-Menü Ansicht – Eigenschaften aus. - oder Klicken Sie auf die Taskschaltfläche Eigenschaften. Das Dialogfeld Eigenschaften wird angezeigt. 2 Klicken Sie auf das Register Allgemein und wählen Sie das Dropdown-Menü für Standort, Abteilung oder Aufstellungsort aus.
- oder Klicken Sie mit der rechten Maustaste auf den Knoten Verzeichnisse und wählen Sie Neues Verzeichnis aus. Das Dialogfeld Neues Verzeichnis wird angezeigt. 3 Geben Sie einen Namen für das Verzeichnis mit 1 bis 32 Zeichen ein. Bei den Verzeichnisnamen wird nicht zwischen Groß- und Kleinschreibung unterschieden. Es kann eine beliebige Zeichenkombination über die Tastatur eingegeben werden. Leerzeichen in der Mitte sind zulässig, Leerzeichen am Beginn und am Ende des Namens jedoch nicht.
3 Wählen Sie die Standort-, Aufstellungsort- oder Verzeichnis-Kategorie aus der Dropdown-Liste aus. 4 Wählen Sie in der Liste der verfügbaren Ziele die Zieloption aus, der die Einheit innerhalb der ausgewählten Kategorie zugewiesen werden kann. Diese Liste enthält u. U. keinen Eintrag, wenn noch kein Standort, Aufstellungsort oder Verzeichnis in der lokalen Datenbank definiert wurde. 5 Klicken Sie auf OK, um die Zuweisung zu speichern.
Aktionen resultiert jedoch darin, dass Einheiten aus der lokalen Datenbank gelöscht werden. Die Funktion zum Umbenennen ist ebenfalls kontextabhängig. In der Einheitenliste können Sie einen Remote Console Switch oder Server auswählen und umbenennen. In der Baumstruktur des Gruppenauswahl-Fensters können Sie Servertypen, Standorte, Abteilungen und Verzeichnisse auswählen und umbenennen. So löschen Sie einen Remote Console Switch oder Server: 1 Wählen Sie eine Einheit im Einheitenauswahl-Fenster aus.
Drücken Sie auf Ihrer Tastatur die Entf-Taste. Ein Dialogfeld wird angezeigt, das die von diesem Löschvorgang betroffene Anzahl von Einheiten bestätigt. 3 Klicken Sie auf Ja, um den Löschvorgang zu bestätigen. In Abhängigkeit von Ihrer Konfiguration können zusätzliche Meldungen angezeigt werden. Reagieren Sie auf diese Meldungen wie erforderlich. Das Element wird gelöscht. - oder Klicken Sie auf Nein, um den Vorgang abzubrechen.
Anwendung ausgeführt wird, kann die Größe des Fensters manuell verändert werden; diese Einstellungen werden aber nicht gespeichert. Wenn der Explorer das nächste Mal gestartet wird, wird das Fenster wieder in seiner Standardgröße und Standard-Bildschirmposition angezeigt. Eine Bildschirmunterteilung, die von oben nach unten verläuft, trennt das Gruppenauswahl-Fenster vom Einheitenauswahl-Fenster. Sie können die Unterteilung nach links oder rechts bewegen, um den Anzeigebereich des Gruppenauswahl- bzw.
Ändern des Standard-Browsers Sie können festlegen, welcher Browser aufgerufen werden soll, wenn eine ServerURL in einem Browser-Fenster angezeigt wird. Sie haben die Möglichkeit, den Standard-Browser für Ihr System zu verwenden, oder Sie können einen bestimmten Browser für diesen Server aufrufen. So ändern Sie den Standard-Browser: 1 Wählen Sie im Explorer-Menü Extras – Optionen aus. Das Dialogfeld Optionen wird angezeigt. 2 Deaktivieren Sie das Kontrollkästchen Standard-Browser starten.
geladen werden, auf dem sie erstellt wurde, oder sie kann auf eine andere ClientWorkstation geladen werden. Die gespeicherte Datenbank wird in einer ZIPDatei komprimiert. Während die Datenbank gespeichert wird, kann keine andere Aktion ausgeführt werden und alle anderen Fenster müssen geschlossen sein.
3 Klicken Sie auf Laden. Während des Ladens wird eine Statusanzeige eingeblendet. Nach Abschluss dieses Vorgangs wird eine Meldung angezeigt, dass das Laden erfolgreich abgeschlossen wurde. Danach wird wieder das Hauptfenster angezeigt. Exportieren einer Datenbank Mit dieser Funktion können Sie Felder aus der lokalen Datenbank in eine durch Komma getrennte ASCII-Datei (CSV) oder durch Tabulator getrennte Datei (TSV) exportieren. Die folgenden Datenbankfelder werden exportiert.
Switch oder Server. Die Datei enthält eine Zeile für jeden Remote Console Switch und Server, der in der lokalen Datenbank definiert ist. So exportieren Sie eine Datenbank: 1 Wählen Sie im Explorer-Menü Datei - Datenbank - Export aus. Das Dialogfeld Datenbank exportieren wird angezeigt. 2 Geben Sie einen Dateinamen ein und suchen Sie in der Verzeichnisstruktur nach dem Speicherort für die exportierte Datei. 3 Wählen Sie aus der Dropdown-Liste für den Dateityp das gewünschte Exportformat aus.
4 Verwenden des Viewers Über den Viewer können Sie eine Verbindung zu einem Server im Remote Console Switch-System herstellen. Mit dem Viewer verfügen Sie über die vollständige Steuerung von Tastatur, Monitor und Maus eines Servers. Sie können auch eine von Ihnen angelegte Serverliste scannen, indem Sie in der Miniaturansicht einzelne Server aktivieren. Diese Ansicht enthält eine Reihe von Miniaturansichten, die kleine, skalierte, nicht interaktive Versionen der Bildschirmanzeige eines Servers darstellen.
Abbildung 4.1: RCS Software –Register „Server“ So greifen Sie auf einen Server zu: 1 Klicken Sie im Explorer auf das Register Server. 2 Wählen Sie im Einheitenauswahl-Fenster einen Server aus. 3 Klicken Sie auf die Taskschaltfläche Video verbinden. - oder Klicken Sie mit der rechten Maustaste auf den Server. Ein Popup-Menü wird angezeigt. Wählen Sie Video verbinden aus. - oder Doppelklicken Sie auf den Servernamen. - oder Drücken Sie die .
1 Klicken Sie auf das Register Server und positionieren Sie den Cursor im Suchtextfeld. 2 Geben Sie den zu suchenden Text ein. Dabei kann es sich um den Servernamen oder um andere Informationen handeln, die Sie in den anderen Kopfzeilen der Einheitenauswahl-Liste eingegeben haben, wie z. B. Typ oder Aufstellungsort. 3 Klicken Sie auf die Schaltfläche Suchen. Die Ergebnisse werden in der Einheitenliste angezeigt. 4 Überprüfen Sie die Ergebnisse Ihrer Suche.
Funktionen des Viewer-Fensters Abbildung 4.2: Viewer-Fenster 1 Menüleiste: Zugriff auf viele Funktionen des Viewers. 2 Server-Desktop, auf den zugegriffen wird: Durch dieses Fenster interagieren Sie mit dem Server.
Viewer-Menüleiste Abbildung 4.3: Viewer-Menüleiste 1 Pin: Klicken Sie auf den Pin, um die Menüleiste in Position zu halten. Dadurch wird gewährleistet, dass die Menüleiste nicht ausgeblendet wird, wenn Sie den Mauszeiger von der Menüleiste weg bewegen. 2 Menüoptionen: Die Menüs bieten Zugriff auf Funktionen, die im Viewer zur Verfügung stehen. 3 Schaltflächen der Symbolleiste: Sie können der Symbolleiste bis zu zehn Schaltflächen hinzufügen.
Verbindungsstatusanzeige Teilungs-Modus Aktive Verbindung (normale, nicht exklusive Sitzung, ohne Teilen) Aktives Teilen (Primärbenutzer) Aktives Teilen (Sekundärbenutzer) Passives Teilen Tarnmodus Scan-Modus 5 Smart Card-Statusanzeige: Der Smart Card-Status wird durch ein Smart Card-Symbol auf der äußerst rechten Seite der Video Viewer-Symbolleiste angezeigt. Tabelle 4.
Anpassen des Viewers Sie können die Viewer-Einstellungen an Ihre Anforderungen anpassen, einschließlich der Einstellungen für Bildschirmauflösung, Symbolleiste und Tastaturmakros. Anpassen der Viewer-Symbolleiste Sie können der Symbolleiste bis zu zehn Schaltflächen hinzufügen. Mithilfe dieser Schaltflächen wird der schnelle Zugriff auf die festgelegten Funktionen und Tastaturmakros ermöglicht.
Abbildung 4.4: Dialogfeld „Sitzungsoptionen“ – Register „Symbolleiste“ Einstellen der Zeitverzögerung für das Ausblenden der Symbolleiste Die Symbolleiste wird ausgeblendet, sobald Sie den Mauszeiger wegbewegen, es sei denn, die Schaltfläche Pin wurde aktiviert. Sie können die Zeitdauer zwischen Bewegen des Mauszeigers und Ausblenden der Symbolleiste anpassen, indem Sie die Verzögerung für das Ausblenden der Symbolleiste festlegen.
Symbolleiste angezeigt werden soll, nachdem der Mauszeiger wegbewegt wurde. 4 Klicken Sie auf OK, um die vorgenommenen Änderungen zu übernehmen und zum Hauptfenster des Viewers zurückzukehren. Viewer vergrößern und aktualisieren Standardmäßig werden drei Schaltflächen in der Viewer-Symbolleiste angezeigt, mit denen Sie die Anzeige des Viewers anpassen können. Mit der ersten Schaltfläche kann der Viewer auf den Einzelcursor-Modus eingestellt werden.
Klicken Sie in der Viewer-Symbolleiste auf Lokalen Cursor ausrichten. Der lokale Cursor wird auf den Cursor des Remote-Servers ausgerichtet. So wechseln Sie in den Vollbildmodus: Klicken Sie in der oberen rechten Ecke des Viewers auf die Schaltfläche Maximieren. - oder Wählen Sie im Viewer-Menü Ansicht - Vollbild aus. Das Desktop-Fenster wird ausgeblendet und nur der Server-Desktop, auf den gerade zugegriffen wird, ist sichtbar.
Wählen Sie in der Menüleiste Ansicht – Skalierung – Automatische Skalierung aus, damit die Bildschirmanzeige des Servers automatisch skaliert wird. - oder Wählen Sie in der Menüleiste Ansicht - Skalierung - Vollbild. - oder Wählen Sie eine Bildschirmauflösung aus dem Untermenü Manuelle Skalierung aus. Abbildung 4.6: Viewer-Skalierung Anpassen der Videoqualität Der Viewer bietet Ihnen die Möglichkeit, Monitoranpassungen sowohl automatisch als auch manuell vorzunehmen.
Anpassen der Farbtiefe HINWEIS: Der Befehl „Farben“ kann nur vom Primärbenutzer verwendet werden. Er steht anderen Benutzern, die im Teilungs-Modus an der Sitzung teilnehmen, nicht zur Verfügung. HINWEIS: Wenn die Option „Aktualisierung im Hintergrund“ im Dialogfeld „Sitzungsoptionen“ aktiviert ist, wird die Farbtiefe automatisch auf die optimale verfügbare Farbe eingestellt und kann nicht geändert werden.
3 Verwenden Sie den Schieberegler oder klicken Sie auf die Schaltfläche Minus (–) oder Plus (+), um die Parameter für jedes geklickte Symbol einzustellen. Die Einstellungen werden sofort im Viewer-Fenster sichtbar. 4 Wenn Sie den Vorgang beendet haben, klicken Sie auf Schließen, um das Dialogfeld Manuelle Monitoranpassung zu verlassen. Optionen des Dialogfelds „Manuelle Monitoranpassung“ Abbildung 4.
6 Helligkeit 7 Rauschschwelle 8 Prioritätsschwelle 9 Automatische Monitoranpassung 10 Bild aktualisieren 11 Schieberegler 12 Testbild 13 Hilfe 14 Systemmonitor 15 Schaltfläche „Schließen“ Minimieren der Farbverfälschungen von Remote-Videositzungen Beim Aufbau von Remote-Videositzungen können Pixel-Farbverfälschungen aufgrund bestimmter Netzwerkbedingungen auftreten. Dieses Problem tritt meistens bei deckenden Hintergrundfarben auf.
HINWEIS: Die Absenkung der Rauschschwelle auf Null verursacht eine konstante Bildaktualisierung, starke Netzwerkauslastung und ein flackerndes Bild. Dell empfiehlt, die Rauschschwelle auf den höchsten Wert einzustellen, mit dem eine effiziente Systemleistung erreicht und gleichzeitig die Pixelfarben des Mauszeigerpfads wiederhergestellt werden können.
Abbildung 4.8: Viewer-Dialogfeld „Sitzungsoptionen für Maus“ Einstellen der Maus-Skalierung Sie können zwischen drei voreingestellten Optionen für die Maus-Skalierung wählen oder Ihre eigene Skalierung einrichten. Die drei Voreinstellungen sind: Standard (1:1), Hoch (2:1), oder Niedrig (1:2). Bei einem Skalierverhältnis von 1:1 sendet jede Mausbewegung auf dem Desktop-Fenster die gleiche Mausbewegung an den Server.
4 Geben Sie die Werte für die Maus-Skalierung in die Felder X und Y ein. Jede Mausbewegung wird mit den entsprechenden X- und Y-Skalierungsfaktoren multipliziert. Der zulässige Eingabebereich liegt zwischen 0,25 und 3,00. Minimieren des Mausspureffekts Wenn sich der Mauszeiger während einer Remote-Videositzung über den Bildschirm bewegt, behalten einige Pixel eine Farbverfälschung bei.
Verbessern der Mausleistung Wenn Sie während einer Remote-Videositzung langsame Mausreaktionen feststellen oder die Mauszeiger nicht mehr synchronisiert sind, sollten Sie die Mausbeschleunigung im Betriebssystem des Zielservers deaktivieren. Microsoft Windows: 1 Deaktivieren Sie die Mausbeschleunigung. 2 Stellen Sie die Mausgeschwindigkeit so ein, dass sich der Schieberegler genau in der Mitte befindet.
4 Starten Sie die RCS Software neu. Anzeigen von mehreren Servern über den Scan-Modus Mit dem Viewer können Sie mehrere Server gleichzeitig in den Miniaturansichten des Scan-Modus anzeigen. Diese Ansicht enthält eine Reihe von Miniaturansichten, die kleine, skalierte, nicht interaktive Versionen der Bildschirmanzeige eines Servers darstellen. Unter jeder Miniaturansicht werden der Servername sowie eine Statusanzeige angezeigt.
Abbildung 4.9: Viewer –Miniaturansichten Der Scan-Modus besitzt eine niedrigere Priorität als eine aktive Verbindung. Wenn eine interaktive Sitzung mit einem Server besteht, wird dieser Server in der Scan-Sequenz übergangen und der Scan-Modus geht zum nächsten Server über. Es wird keine Fehlermeldung beim Anmelden angezeigt. Nach Beendigung der interaktiven Sitzung wird die Miniaturansicht wieder in die Scan-Sequenz aufgenommen.
Zugriff auf den Scan-Modus über die RCS Software Abbildung 4.10: RCS Software –Scannen der Server So greifen Sie in der RCS Software auf den Scan-Modus zu: 1 Wählen Sie im Explorer das Register Remote Console Switches, Server, Standorte oder Verzeichnisse aus. 2 Wählen Sie im Fenster Einheitenauswahl mindestens zwei Server durch Drücken der Umschalttaste aus. - oder Drücken Sie die -Taste. Die Taskschaltfläche Scan-Modus wird angezeigt. 3 Klicken Sie auf die Taskschaltfläche Scan-Modus.
Statusanzeigen der Miniaturansicht Die grüne LED zeigt an, dass ein Server momentan gescannt wird. Das rote X bedeutet, dass der letzte Scan des Servers nicht erfolgreich war. Das heißt, dass der Scan aufgrund von Zugriffsrechten oder Pfadfehlern (der Serverpfad auf dem Remote Console Switch war nicht verfügbar) oder aus anderen Gründen nicht durchgeführt werden konnte. Wenn Sie den Mauszeiger über dem roten X platzieren, wird eine QuickInfo angezeigt, die den Grund für den Fehler angibt.
Klicken Sie mit der rechten Maustaste auf eine Server-Miniaturansicht und wählen Sie Interaktive Sitzung anzeigen aus. Der Server-Bildschirm wird in einem interaktiven Viewer-Fenster gestartet. So aktivieren oder deaktivieren Sie einen Server in der Scan-Sequenz: 1 Wählen Sie eine Server-Miniaturansicht aus. 2 Wählen Sie in der Anzeige der Miniaturansichten Miniaturansicht – [Servername] – Aktivieren aus.
einer Auswahl von verfügbaren Tastenanschlägen für Microsoft Windows-, Sunund Linux-Systeme zur Verfügung. So wählen Sie das verwendete System aus: Klicken Sie im Viewer auf das Menü Makros. Klicken Sie auf Im Menü anzeigen und wählen Sie entweder Windows, Sun oder Linux aus. So senden Sie Tastenanschläge an den Server: Klicken Sie im Viewer auf das Menü Makros und wählen Sie den Namen des Makros aus, das die Tastenanschläge enthält, die Sie an den Server senden möchten. Abbildung 4.11, Abbildung 4.
Abbildung 4.12: Erweitertes Viewer-Menü „Makros“ – Option „Sun“ Abbildung 4.
befinden, sowie die Tastaturanschlag-Menüaktivierung sowie die Aktualisierung im Hintergrund. Durch Aktivieren oder Deaktivieren des Kontrollkästchens TastaturanschlagWeitergabe können Sie bestimmen, ob der Modus TastaturanschlagWeitergabe aktiviert sein soll. Standardmäßig ist die Option TastaturanschlagWeitergabe nicht aktiviert. Abbildung 4.
1 Wählen Sie im Menü Extras im Viewer den Befehl Sitzungsoptionen. Die Symbolleiste „Sitzungsoptionen“ wird angezeigt. 2 Klicken Sie auf das Register Allgemein. 3 Ändern Sie die Sitzungsoptionen wie gewünscht. 4 Klicken Sie auf OK. Bildschirmaufzeichnung Mit dem Viewer können Sie den Inhalt des Bildschirms aufzeichnen und in einer Datei speichern oder in die Zwischenablage kopieren. So speichern Sie den Bildschirminhalt als Datei: 1 Wählen Sie im Viewer die Befehle Datei – In Datei speichern.
wird als Primärbenutzer bezeichnet.
Sekundärbenutzer können entweder „aktive Benutzer“ sein, d. h., sie können Maus- und Tastaturdaten eingeben, oder „passive Benutzer“, die keine Mausund Tastaturdaten eingeben können. Wenn die Option Automatisches Teilen am Remote Console Switch aktiviert ist, benötigen Sekundärbenutzer nicht die Erlaubnis des Primärbenutzers, um an einer Sitzung teilzunehmen.
4 Aktivieren Sie im Bereich „Verbindung teilen“ das Kontrollkästchen Teilungsmodus aktivieren. 5 Sie können die Option Automatisches Teilen aktivieren. Dies ermöglicht es Sekundärbenutzern, eine KVM-Sitzung automatisch zu teilen, ohne erst die Berechtigung vom Primärbenutzer anzufordern. So teilen Sie eine digitale Verbindung: 1 Klicken Sie im Explorer auf die Schaltfläche Geräte. 2 Führen Sie einen der folgenden Schritte aus: • Doppelklicken Sie in der Einheitenliste auf das Zielgerät.
• Klicken Sie auf Nein, um die Teilungsanfrage abzubrechen. Wenn der Primärbenutzer die Teilungsanfrage akzeptiert oder die Option „Automatisches Teilen“ aktiviert wurde, wird eine KVM-Sitzung auf der Zielgerätesitzung geöffnet. Das Sitzungstyp-Symbol im Video Viewer-Fenster weist daraufhin, ob der Sitzungsstatus aktiv oder passiv ist. Wenn die Teilungsanfrage abgelehnt wird, werden Sie in einer Meldung darüber informiert. Administratoren stehen an dieser Stelle mehrere Möglichkeiten zur Verfügung.
• Doppelklicken Sie in der Einheitenliste auf einen Remote Console Switch. • Markieren Sie in der Einheitenliste einen Remote Console Switch und klicken Sie dann auf die Schaltfläche Einheit verwalten. • Klicken Sie mit der rechten Maustaste in der Einheitenliste auf einen Remote Console Switch. Wählen Sie im Popup-Menü die Option Einheit verwalten aus. • Wählen Sie in der Einheitenliste einen Remote Console Switch aus und drücken Sie die Eingabetaste.
Sekundärbenutzer können die exklusive KVM-Sitzung nicht teilen. Administratoren oder Benutzer mit bestimmten Zugriffsrechten können jedoch die Sitzung weiterhin beenden. Getarnte Verbindung Administratoren können im Tarnmodus eine Verbindung mit einem Zielgerät herstellen, um die Videoausgabe eines Remote-Benutzers ohne sein Wissen anzuzeigen. Im Tarnmodus verfügen Administratoren nicht über die Steuerung von Tastatur und Maus des Zielgeräts.
3 • Wählen Sie das Zielgerät aus und klicken Sie dann auf die Schaltfläche Video verbinden. • Klicken Sie mit der rechten Maustaste auf das Zielgerät. Wählen Sie im Popup-Menü die Option Video verbinden aus. • Markieren Sie das Zielgerät und drücken Sie die Eingabetaste. Wenn ein anderer Benutzer dieses Zielgerät momentan anzeigt, werden Sie in einer Meldung darüber informiert, dass das Zielgerät bereits eine KVMSitzung ausführt.
Trennungsmodus Durch Trennen (oder exklusives Starten) von Sitzungen können Benutzer mit den entsprechenden Zugriffsberechtigungen die Steuerung eines Servers von einem anderen Benutzer mit weniger oder gleichen Berechtigungen übernehmen. HINWEIS: Eine Warnmeldung wird an alle Benutzer gesendet, die an der Verbindung teilnehmen, aber nur der Primärbenutzer kann eine Trennanforderung zurückweisen (falls zugelassen).
Aktueller Benutzer Trennung durch Trennung kann zurückgewiesen werden Remote-Administrator Remote Console SwitchAdministrator Nein Lokaler Benutzer Remote-Administrator Ja Lokaler Benutzer Remote Console SwitchAdministrator Ja Trennen einer Remote-Benutzer-Verbindung durch einen RemoteAdministrator Wenn ein Remote-Administrator versucht, auf einen Server zuzugreifen, der von einem Remote-Benutzer verwendet wird, wird der Administrator in einer Nachricht gebeten, so lange zu warten, bis der Benut
Remote-Administrator mit einer Meldung informiert, dass seine Anfrage zurückgewiesen wurde und kein Zugriff auf den Server möglich ist. HINWEIS: Falls der angezeigte Server an einen Avocent Switch angeschlossen ist, hat der Benutzer keine Möglichkeit, die Unterbrechung anzunehmen oder abzulehnen. HINWEIS: Falls eine Trennanforderung zurückgewiesen werden kann, wird das Dialogfeld „Trennanforderung für die Sitzung“ angezeigt.
5 • Klicken Sie auf OK oder Ja. Der Primärbenutzer wird in einer Meldung über die Trennanforderung informiert. Je nach Ihren Zugriffsrechten kann der Primärbenutzer die Trennanforderung ablehnen. • Klicken Sie auf Nein, damit der Primärbenutzer die Sitzung beibehalten kann. Nach der Trennung wird der Video Viewer der Zielgerätesitzung geöffnet.
• Sie können ein DVD-ROM-Laufwerk und ein Massenspeichergerät gleichzeitig zuweisen. • Ein CD/DVD-ROM-Laufwerk oder eine ISO-Diskette-Image-Datei wird als virtuelles DVD-Laufwerk zugewiesen. • Diskettenlaufwerke, Disketten-Image-Dateien, USB-Speichergeräte oder andere Speichermedien werden als virtuelle Massenspeichergeräte zugewiesen.
Trennen von Sitzungen zur Verfügung. Zum Beispiel können die KVM- und Virtual Media-Sitzungen zusammen gesperrt werden. Wenn in diesem Modus eine KVM-Sitzung getrennt wird, wird auch die zugehörige Virtual Media-Sitzung getrennt. Wenn die Sitzungen nicht zusammen gesperrt wurden, kann die KVM-Sitzung geschlossen werden, die Virtual Media-Sitzung bleibt jedoch aktiv.
2 Wählen Sie Extras – Virtual Media aus. 3 Wenn diese Sitzung als reservierte Sitzung festgelegt werden soll, klicken Sie im Fenster „Virtual Media“ auf Details und aktivieren Sie dann das Kontrollkästchen Reserviert. Für die Zuordnung auf dem Zielserver stehen zwei Geräte zur Verfügung: ein Disketten-/Flash-Laufwerk und ein CD/DVD-Laufwerk. Der Virtual Media Client ermöglicht die gleichzeitige Zuordnung von jeweils einem Laufwerk pro Option.
festgelegt wurde, Sie jedoch den Zugriff eines bestimmten Laufwerks auf schreibgeschützt einschränken möchten. 3 So können Sie ein ISO- oder Diskette-Image als Virtual Media-Laufwerk hinzufügen und zuordnen: a. Klicken Sie im Fenster „Virtual Media“ auf Image hinzufügen. b. Das Dialogfeld zum Auswählen der allgemeinen Datei wird geöffnet, wobei das Verzeichnis mit den Diskette-Image-Dateien (Erweiterung .iso oder .img) angezeigt wird.
Virtual Media-Verbindungsstatus Im Bereich „Status“ werden bestimmte Informationen über die Virtual MediaVerbindungen angezeigt. Wenn keine aktuelle Verbindung besteht, wird in den Spalten „Keine Verbindung“ bzw. „n/a“ angezeigt. Führen Sie folgende Schritte durch, um den Status des Virtual Media-Laufwerks anzuzeigen: 1 2 Klicken Sie im Virtual Media-Fenster auf Details. Das Dialogfeld wird erweitert, und die Details-Tabelle wird eingeblendet.
Media-Sitzung.) Bei Beenden einer gesperrten Virtual Media-Sitzung wird die entsprechende KVM-Sitzung allerdings nicht beendet. • Zugriff auf zugeordnetes Laufwerk – Sie können den Zugriffsmodus für zugeordnete Laufwerke auf schreibgeschützt einstellen. Im schreibgeschützten Zugriffsmodus können keine Daten auf das zugeordnete Laufwerk des Clientcomputers geschrieben werden. Wenn der Zugriffsmodus nicht schreibgeschützt ist, können Sie Daten auf das zugeordnete Laufwerk schreiben bzw. von diesem lesen.
Zurücksetzen des USB-Busses Mit dieser Funktion werden alle USB-Geräte auf dem Zielgerät einschließlich Tastatur und Maus zurückgesetzt. Sie sollte daher nur verwendet werden, wenn das Zielgerät nicht reagiert. So setzen Sie den USB-Bus zurück: 1 Klicken Sie im Virtual Media-Fenster auf Details. 2 Wählen Sie USB zurücksetzen aus.
zugewiesen wird, wird es ohne vorhandenes Speichermedium angezeigt. Wenn dem Zielgerät ein Virtual Media-Gerät zugewiesen wird, wird auf dem Zielgerät angezeigt, dass ein Speichermedium eingelegt wurde. Wenn das Virtual MediaGerät nicht zugewiesen wird, wird auf dem Zielgerät angezeigt, dass das Speichermedium entfernt wurde. Daher wird die Verbindung des virtuellen USB2-Geräts nicht vom Zielgerät getrennt. Der USB2-SIP stellt die Tastatur und die Maus als ein USB2-Verbundgerät dar.
Um festzustellen, ob Ihr Computer von Virtual Media aus gestartet werden kann, führen Sie die folgenden Schritte aus: 1 Schließen Sie ein USB CD-/DVD-ROM-Laufwerk an den Remote Console Switch an, legen Sie eine startfähige Installations-CD/-DVD des Betriebssystems ein und weisen Sie das Laufwerk dem Zielgerät zu. Starten Sie das Zielgerät neu, um festzustellen, ob es vom angeschlossenen CD/DVD-Laufwerk aus gestartet werden kann.
xxx | Verwenden des Viewersxxx
A Anhang A: Aktualisieren der RCS Software Achten Sie darauf, dass Sie im Besitz der neuesten RCS Software-Version sind (erhältlich über die Webseite von Dell unter: www.dell.com/support), damit ein optimaler Betrieb Ihres Systems gewährleistet wird. So aktualisieren Sie die RCS Software: 1 Laden Sie die Aktualisierungsdatei von der Dell Support-Webseite herunter: www.dell.com/support. 2 Doppelklicken Sie auf das Installationsprogramm.
4 Die Installation beginnt. Die Programmdateien, Verknüpfungen, Umgebungsvariablen und Registrierungseinträge (nur bei Win 32-Systemen) werden installiert bzw. durch die neuen Dateien und Einstellungen der aktuellen Version überschrieben. HINWEIS: Damit die Aktualisierungserkennung in Kraft tritt, muss zuerst ein Neustart durchgeführt werden, oder Sie müssen sich abmelden.
B Anhang B: Tastatur und Maus Tabelle B.1: Tastatur- und Maus-Tastenkombinationen im Unterteilungsfenster Vorgang Beschreibung F6 Navigiert zwischen den geteilten Bildschirmen und markiert das letzte Element, auf dem sich der Eingabefokus befand. F8 Markiert die Unterteilung. Pfeil-nach-linksoder Pfeil-nachoben-Taste Verschiebt die Unterteilung nach links, sofern diese markiert ist. Pfeil-nachrechts- oder Pfeil-nachunten-Taste Verschiebt die Unterteilung nach rechts, sofern diese markiert ist.
Tabelle B.2: Tastatur- und Maus-Tastenkombinationen zur Steuerung in der Baumstrukturansicht Vorgang Beschreibung Einfacher Mausklick Hebt die bestehende Auswahl auf und wählt den Knoten aus, über dem sich der Mauszeiger befindet. Doppelter Mausklick Blendet einen erweiterbaren Knoten ein/aus (ein Knoten, der untergeordnete Objekte hat). Keine Aktivität bei einem untergeordneten Knoten (ein Knoten, der keine untergeordneten Objekte hat).
Vorgang Beschreibung Pfeil-nachoben-Taste Hebt die bestehende Auswahl auf und bewegt die Auswahl um eine Zeile nach oben. Pfeil-nachunten-Taste Hebt die bestehende Auswahl auf und bewegt die Auswahl um eine Zeile nach unten. Bild auf Hebt die bestehende Auswahl auf, blättert eine Seite nach oben und wählt die erste Position auf der Seite aus. Bild ab Hebt die bestehende Auswahl auf, blättert eine Seite nach unten und wählt die letzte Position auf der Seite aus.
Vorgang Beschreibung Umschalttaste + Erweitert die Auswahl um eine Seite nach unten. Bild ab Hebt eine bestehende Auswahl auf und wählt die Zeilen zwischen Umschalttaste + der aktuellen Markierung und der Zeile aus, in der sich der Mausklick Mauszeiger befindet, wenn ein Mausklick durchgeführt wird. Strg + Mausklick Kehrt den Auswahlstatus der Zeile um, in der sich der Mauszeiger befindet, ohne dass der Auswahlstatus einer anderen Zeile beeinflusst wird.
C Anhang C: TCP-Ports Die nachfolgende Tabelle zeigt die Funktionen des Remote Console Switch und der verwendeten Ports. Tabelle C.1: Verwendete Ports Port Funktion TCP 80/443 Standard-HTTP/HTTPS TCP 2068 Video Viewer-Video, Tastatur, Maus, Benutzerauthentifizierung und Virtual Media. TCP/UDP 3211 Verwaltung und Installation/Suche. HINWEIS: Die TCP/IP-Ports sind statisch und können nicht geändert werden.
xxx | xxx Anhang C: TCP-Ports
D Anhang D: Technischer Kundendienst Unser technischer Kundendienst steht Ihnen jederzeit bei Fragen hinsichtlich Installations- oder Betriebsproblemen mit Ihrem Produkt von Dell zur Verfügung. Verfahren Sie zur schnellstmöglichen Problemlösung wie folgt. So verfahren Sie zur Problemlösung: 1 Sehen Sie im entsprechenden Abschnitt der Betriebsanleitung nach, ob das Problem mit den vorgeschlagenen Abhilfemaßnahmen gelöst werden kann. 2 Besuchen Sie unsere Website unter www.dell.
xxx | xxx Anhang D: Technischer Kundendienst