Dell Latitude 3400 Service Manual Regulatory Model: P111G Regulatory Type: P111G001
Uwagi, przestrogi i ostrzeżenia UWAGA Napis UWAGA oznacza ważną wiadomość, która pomoże lepiej wykorzystać komputer. OSTRZEŻENIE Napis PRZESTROGA informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu lub utraty danych, i przedstawia sposoby uniknięcia problemu. PRZESTROGA Napis OSTRZEŻENIE informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu, obrażeń ciała lub śmierci. © 2019 Dell Inc. lub podmioty zależne. Wszelkie prawa zastrzeżone.
Contents 1 Serwisowanie komputera.............................................................................................................. 5 Instrukcje dotyczące bezpieczeństwa................................................................................................................................ 5 Wyłączanie komputera — Windows 10..............................................................................................................................
5 Troubleshooting........................................................................................................................104 Program diagnostyczny ePSA (Enhanced Pre-Boot System Assessment)...............................................................104 Przeprowadzanie testu diagnostycznego ePSA...................................................................................................... 104 Diagnostyka................................................................................
1 Serwisowanie komputera Instrukcje dotyczące bezpieczeństwa Wymagania Aby uchronić komputer przed uszkodzeniem i zapewnić sobie bezpieczeństwo, należy przestrzegać następujących zaleceń dotyczących bezpieczeństwa. O ile nie wskazano inaczej, każda procedura opisana w tym dokumencie opiera się na założeniu, że są spełnione następujące warunki: • • Użytkownik zapoznał się z informacjami dotyczącymi bezpieczeństwa, jakie zostały dostarczone z komputerem.
Kroki 1. Kliknij lub stuknij przycisk 2. Kliknij lub stuknij przycisk . , a następnie kliknij lub stuknij polecenie Wyłącz. UWAGA Sprawdź, czy komputer i wszystkie podłączone urządzenia są wyłączone. Jeśli komputer i podłączone do niego urządzenia nie wyłączyły się automatycznie po wyłączeniu systemu operacyjnego, naciśnij przycisk zasilania i przytrzymaj go przez około 6 sekund w celu ich wyłączenia.
2 Technologia i podzespoły DDR4 DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512 GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM. DDR4 synchronous dynamic random-access memory is keyed differently from both SDRAM and DDR to prevent the user from installing the wrong type of memory into the system. DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.
Figure 3. Curved edge Memory Errors Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the system or under the keyboard, as in some portable systems. NOTE: The DDR4 memory is imbedded in board and not a replaceable DIMM as shown and referred.
Szybkość Obecnie w najnowszej specyfikacji standardu USB 3.0/USB 3.1 pierwszej generacji zdefiniowane są 3 tryby szybkości. Są to tryby SuperSpeed, Hi-Speed i Full-Speed. Nowy tryb SuperSpeed ma prędkość przesyłania danych 4,8 Gb/s. W specyfikacji nadal istnieją tryby USB Hi-Speed i Full-Speed, znane szerzej odpowiednio jako USB 2.0 i 1.1. Te wolniejsze tryby nadal działają z szybkością odpowiednio 480 Mb/s i 12 Mb/s. Zostały one zachowane dla zgodności ze starszym sprzętem.
Zgodność Dobra wiadomość: standard USB 3.0/USB 3.1 pierwszej generacji został od podstaw zaplanowany z myślą o bezproblemowym współistnieniu ze standardem USB 2.0. Przede wszystkim mimo że w przypadku standardu USB 3.0/USB 3.1 pierwszej generacji zastosowano nowe fizyczne metody połączeń i kable zapewniające obsługę większych szybkości, samo złącze zachowało taki sam prostokątny kształt i cztery styki rozmieszczone identycznie jak w złączu standardu USB 2.0. W kablu USB 3.0/USB 3.
Feature Specifications Connector M.2 card slot (2230/2280) Configurations supported • • • Capacity 32 GB or 64 GB 7th Generation or higher Intel Core i3/i5/i7 processor Windows 10 64-bit version or higher Intel Rapid Storage Technology driver version 15.9.1.1018 or higher Włączanie pamięci Intel Optane Kroki 1. Na pasku zadań kliknij pole wyszukiwania i wpisz „Technologia pamięci Intel Rapid”. 2. Kliknij pozycję Technologia pamięci Intel Rapid. 3.
Intel UHD Graphics 620 Operating Systems Graphics/ Video API Support DirectX 12 (Windows 10), OpenGL 4.5 Maximum Vertical Refresh Rate Up to 85 Hz depending on resolution Multiple Display Support On System: eDP (internal), HDMI Via Optional USB Type-C Port: VGA, DisplayPort External Connectors HDMI 1.4b USB Type–C port Odpowiednik karty Nvidia GeForce MX130 Tabela 4.
3 Major components of your system 1. Base cover 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. WLAN card Memory modules System board M.2 Solid-state drive or Intel Optane memory—Optional Battery Palmrest assembly Speakers Touchpad assembly Display assembly Hard drive assembly IO board VGA daughterboard System fan Heatsink NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer.
4 Wymontowywanie i instalowanie komponentów Recommended tools The procedures in this document require the following tools: • • • Phillips #0 screwdriver Phillips #1 screwdriver Plastic scribe NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4. Karta Secure Digital Wymontowywanie karty Secure Digital Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Kroki 1.
Instalowanie karty Secure Digital Kroki 1. Wsuń kartę Secure Digital do gniazda, aż zatrzaśnie się w miejscu. 2. Wykonaj procedury przedstawione w rozdziale Po zakończeniu serwisowania komputera.
pokrywa dolna Wymontowywanie pokrywy dolnej Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wymontuj kartę pamięci SD. Kroki 1. Poluzuj dziewięć śrub mocujących pokrywę dolną do zestawu podparcia dłoni i klawiatury.
2. Podważ pokrywę dolną, zaczynając od jej prawej strony.
3. Unieś prawą stronę pokrywy dolnej [1] i zdejmij ją z zestawu podparcia dłoni i klawiatury [2]. Instalowanie pokrywy dolnej Kroki 1. Umieść pokrywę dolną na zestawie podparcia dłoni i klawiatury [1].
2. Dokręć dziewięć śrub mocujących pokrywę dolną do zestawu podparcia dłoni i klawiatury.
Kolejne kroki 1. Zainstaluj kartę pamięci SD. 2. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Akumulator Środki ostrożności dotyczące akumulatora litowo-jonowego OSTRZEŻENIE • Podczas obsługi akumulatora litowo-jonowego zachowaj ostrożność. • Przed wyjęciem z systemu akumulator należy maksymalnie rozładować. Można to zrobić, odłączając zasilacz sieciowy od systemu i czekając na wyładowanie się akumulatora.
2. Wykręć cztery śruby (M2x3) mocujące akumulator do zestawu podparcia dłoni i klawiatury [1]. 3. Wyjmij akumulator z zestawu podparcia dłoni i klawiatury [2].
Instalowanie akumulatora Kroki 1. Dopasuj otwory na śruby w akumulatorze do otworów w zestawie podparcia dłoni i klawiatury [1]. 2. Wkręć cztery śruby (M2x3) mocujące akumulator do zestawu podparcia dłoni i klawiatury [2].
3. Podłącz kabel akumulatora do płyty systemowej.
Kolejne kroki 1. Zainstaluj pokrywę dolną. 2. Zainstaluj kartę pamięci SD. 3. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Dysk twardy Removing the hard drive assembly Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable. Steps 1. Disconnect the hard drive cable from the system board [1]. 2. Peel the tape that secures the hard drive cable to the system board [2]. 3.
Installing the hard drive assembly Steps 1. Align the screw holes on the hard drive assembly with the screw holes on the palm rest and keyboard assembly [1]. 2. Replace the four (M2x4.5) screws that secure the hard drive assembly to the palm rest and keyboard assembly [2].
3. Adhere the tape that secures the hard drive cable to the system board [1]. 4. Connect the hard drive cable to the system board [2].
Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Płyta IO Removing the IO board Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Remove the hard drive assembly. NOTE: Required for systems with 42 Whr battery Steps 1.
Installing the IO board Steps 1. Using the alignment posts, place the I/O board on the palm rest and keyboard assembly [1]. 2. Replace the two (M2x3) screws that secure the I/O board to the palm rest and keyboard assembly [2].
3. Adhere the I/O board cable to the palm rest and keyboard assembly [1]. 4. Connect the I/O board cable to the system board and close the latch to secure the cable [2].
Next steps 1. Replace the hard drive assembly. NOTE: Required for systems with 42 Whr battery 2. 3. 4. 5. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Tabliczka dotykowa Removing the touchpad assembly Prerequisites NOTE: For information only, touchpad is included with the palmrest assembly. 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover.
5. Remove the four (M2x2) screws that secure the touchpad to the palmrest and keyboard assembly [1]. 6. Lift the touchpad off the palmrest and keyboard assembly [2].
Instalowanie zestawu tabliczki dotykowej Informacje na temat zadania UWAGA Upewnij się, że tabliczka dotykowa jest dopasowana do prowadnic na zestawie podparciu dłoni i klawiatury, a odstęp po obu stronach tabliczki dotykowej jest taki sam. Kroki 1. Umieść tabliczkę dotykową w gnieździe zestawu podparcia dłoni i klawiatury [1]. 2. Wkręć cztery śruby (M2x2) mocujące tabliczkę dotykową do zestawu podparcia dłoni i klawiatury [2]. 3.
5. Umieść wspornik tabliczki dotykowej w gnieździe w zestawie podparcia dłoni i klawiatury [1]. 6. Wkręć trzy śruby (M2x2) mocujące wspornik tabliczki dotykowej do zestawu podparcia dłoni i klawiatury [2] i przyklej taśmę mocującą wspornik do zestawu.
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Moduły pamięci Removing the memory module Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable. Steps 1. Pry the clips securing the memory module until the memory module pops-up [1]. 2.
NOTE: If you do not hear the click, remove the memory module and reinstall it. Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer SIM Card Removing the SIM card Prerequisites 1. Follow the procedure in Before working inside your computer Steps 1. Open the latch that covers the SIM card slot to release it from the system [1]. 2. Insert a needle in the slot and push it to eject the SIM card tray [2].
Installing the SIM card Steps 1. Open the latch that covers the SIM card slot to release it from the system [1]. 2. Insert a needle in the slot and push it to eject the SIM card tray [2]. 3. Pull the SIM card try and place the SIM card on the SIM cad tray [3] and [4]. 4. Slide the SIM card tray into the slot until it clicks into place.
5. Follow the procedures in After working inside your computer. Karta sieci WLAN Removing the WLAN card Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable. Steps 1. Remove the single (M2x3) screw that secures the WLAN card bracket to the system board [1]. 2. Slide and remove the WLAN card bracket that secures the WLAN cables [2]. 3.
Installing the WLAN card About this task CAUTION: To avoid damage to the WLAN card, do not place any cables under it. Steps 1. Insert the WLAN card into the connector on the system board [1]. 2. Connect the WLAN cables to the connectors on the WLAN card [2]. 3. Place the WLAN card bracket to secure the WLAN cables to the WLAN card [3]. 4. Replace the single (M2x3) screw to secure the WLAN bracket to the WLAN card [4].
Next steps 1. 2. 3. 4. Disconnect the battery cable. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Dysk SSD / pamięć Intel Optane Removing the M.2 2280 Solid-state drive or Intel Optane memory— Optional Prerequisites NOTE: Disable the Intel Optane memory before removing the Intel Optane memory module from your computer. For more information about disabling the Intel Optane memory, see disabling Intel Optane memory 1. 2. 3. 4.
3. Slide and remove the thermal plate from the solid-state drive/Intel Optane card slot [3]. 4. Remove the single (M2x2) screw that secures the solid-state drive/Intel Optane card to the palmrest and keyboard assembly [1]. 5. Slide and lift the solid-state drive/Intel Optane card off the palmrest and keyboard assembly [2].
Installing the M.2 2280 Solid-state drive or Intel Optane memory Optional Steps 1. Slide and insert the tab solid-state drive/Intel Optane card into the solid-state drive/Intel Optane card slot [1]. 2. Replace the single (M2x2) screw that secures the solid-state drive/Intel Optane card to the palmrest and keyboard assembly [2].
Wymontowywanie i instalowanie komponentów 43
3. Align and replace the thermal plate on the solid-state drive/Intel Optane card slot [1,2]. 4. Replace the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [3]. Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Removing the M.2 Solid-state drive bracket Prerequisites 1. 2. 3. 4.
Installing the Solid-state drive bracket Steps 1. Align and replace the solid-state drive bracket on the palmrest and keyboard assembly [1]. 2. Replace the single (M2x3) screw that secures the solid-state drive bracket to the palmrest and keyboard assembly [2].
Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Removing the M.2 2230 Solid-state drive Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable Steps 1. Remove the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [1]. 2.
4. Remove the single (M2x2) screw that secures the solid-state drive to the solid-state drive bracket [1]. 5. Slide and remove the solid-state drive off the solid-state drive slot [2].
Installing the M.2 2230 Solid-state drive Steps 1. Insert the solid-state drive into the solid-state drive slot on the system board [1]. 2. Replace the single (M2x3) screw that secures the solid-state drive to the solid-state drive bracket [2].
3. Align and replace the thermal plate on the solid-state drive [1,2]. 4. Replace the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [3].
Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Głośniki Removing the speakers Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Disconnect the battery cable. Steps 1. Disconnect the speaker cable from the system board [1]. 2.
3. Lift the speakers, along with the cable, off the palm rest and keyboard assembly.
Installing the speakers About this task NOTE: If the rubber grommets are pushed out when removing the speakers, push them back in before replacing the speakers. Steps 1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm rest and keyboard assembly.
2. Route the speaker cable through the routing guides on the palm rest and keyboard assembly [1]. 3. Connect the speaker cable to the system board [2].
Next steps 1. 2. 3. 4. Replace the battery cable. Replace the base cover Replace the SD memory card Follow the procedure in after working inside your computer Wentylator systemowy Removing the system fan Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Steps 1. Disconnect the VGA board cable [1], and the display cable [2, 3] from the system board .
2. Unroute the VGA board cable and the display cable from the routing guides on the fan [1]. 3. Disconnect the fan cable from the system board [2]. 4. Remove the two (M2x3) screws that secure the fan to the palmrest and keyboard board assembly [1].
5. Lift the fan off the palmrest and keyboard board assembly [2]. Installing the system fan Steps 1. Align the screw holes on the fan with the screw holes on to the palm rest and keyboard board assembly [1]. 2. Replace the two (M2x3) screws that secure the fan to the palm rest and keyboard board assembly [2].
3. Connect the fan cable to the system board [1]. 4. Route the VGA board cable and the display cable through the routing guides on the fan [2].
5. Connect the VGA board cable [1], and the display cable [2, 3] to the system board. Next steps 1. 2. 3. 4. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Radiator Removing the heatsink—UMA Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Steps 1.
Instalowanie radiatora — konfiguracja UMA Kroki 1. Umieść radiator na płycie systemowej i dopasuj otwory na śruby w radiatorze do otworów w płycie systemowej [1]. 2. W kolejności wskazanej na radiatorze dokręć cztery śruby mocujące radiator do płyty systemowej [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Wymontowywanie radiatora — konfiguracja z autonomiczną kartą graficzną Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj kartę pamięci SD. Wymontuj pokrywę dolną. Wymontuj akumulator. Kroki 1. Poluzuj siedem śrub mocujących radiator do płyty systemowej [1].
Instalowanie radiatora — konfiguracja z autonomiczną kartą graficzną Kroki 1. Umieść radiator na płycie systemowej i dopasuj otwory na śruby w radiatorze do otworów w płycie systemowej [1]. 2. W kolejności wskazanej na radiatorze dokręć siedem śrub mocujących radiator do płyty systemowej [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Karta rozszerzeń VGA Removing the VGA daughterboard Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Steps 1. Disconnect the VGA daughterboard cable from the system board [1]. 2.
3. Remove the two (M2x3) screws that secure the VGA daughterboard to the palmrest and keyboard assembly [1]. 4. Lift the VGA daughterboard away from the system [2].
Instalowanie karty rozszerzeń VGA Kroki 1. Umieść kartę rozszerzeń VGA i wyrównaj otwory na śruby w karcie z otworami w zestawie podparcia dłoni i klawiatury [1]. 2. Wkręć dwie śruby (M2x3) mocujące kartę rozszerzeń VGA do zestawu podparcia dłoni i klawiatury [2]. 3. Umieść kabel karty VGA w prowadnicach na wentylatorze [1], a następnie podłącz kabel karty rozszerzeń VGA do płyty systemowej [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. płyta przycisku zasilania Removing the power button board with optional fingerprint reader Prerequisites 1. 2. 3. 4. 5. 6. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Remove the system fan. Remove the display assembly. Steps 1.
4. Remove the single (M2x3) screw that secures the power button board to the palmrest and keyboard assembly [1]. 5. Lift the power button board, along with the cable off the palmrest and keyboard assembly [2].
Installing the power button board with optional fingerprint reader Steps 1. Place the power-button board into the slot on the palmrest and keyboard assembly [1]. 2. Replace the single (M2x3) screw that secures the power button board to the palmrest and keyboard assembly [2]. 3. Affix the conductive tape to the power button board [1]. 4. Affix the power button cable to the palmrest and keyboard assembly [2]. 5.
Next steps 1. 2. 3. 4. 5. 6. Replace the display assembly. Replace the system fan. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Płyta systemowa Removing the system board Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover. Remove the battery. Remove the WLAN. Remove the Memory. Remove the SSD. Remove the system fan.
a) b) c) d) e) Power button board [1]. Fingerprint reader (optional) [2]. IO board [3]. Touchpad [4]. Keyboard [5]. 2. Disconnect the following cables from the system board: a) DC-in [1, 2]. b) Speaker [3].
3. Remove the three (M2x3) screws and two (M2x2) screws that secure the system board to the palmrest and keyboard assembly [1]. 4. Lift the system board off the palm-rest and keyboard assembly [2].
Installing the system board Steps 1. Align the screw hole on the system board with the screw hole on the palmrest and keyboard assembly [1]. 2. Replace the three (M2x3) screws and two (M2x2) screws that secure the system board to the palmrest and keyboard assembly [2].
3. Connect the following cables to the system board: a) DC-in [1, 2]. b) Speaker [3].
4. Connect the following cables to the system board: a) b) c) d) e) Power button board [1]. Fingerprint reader (optional) [2]. IO board [3]. Touchpad [4]. Keyboard [5].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Replace the display assembly. Replace the heatsink. Replace the system fan. Replace the SSD. Replace the Memory. Replace the WLAN. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Zestaw wyświetlacza Removing the display assembly Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the SD memory card. Remove the base cover.
3. Unroute the display cable from the routing guides on the palmrest and keyboard assembly [1]. 4. Remove the six (M2.5x5) screws that secure the left and right hinges to the system board, and palmrest and keyboard assembly [2].
5. Lift the palmrest and keyboard assembly at an angle [1]. 6. Continue to lift the palmrest and keyboard assembly until it separates from the hinges [2].
7. Slide and remove the palmrest and keyboard assembly off the display assembly.
8. After performing all the preceding steps, you are left with display assembly. Installing the display assembly About this task NOTE: Ensure that the hinges are opened to the maximum before replacing the display assembly on the palmrest and keyboard assembly. Steps 1. Align and place the palmrest and keyboard assembly under the hinges on the display assembly.
2. Press the hinges down on the system board, and palmrest and keyboard assembly [1]. 3. Seat the palmrest and keyboard assembly on the display assembly [2].
4. Replace the six (M2.5x5) screws that secure the left and right hinges to the system board, and palmrest and keyboard assembly [1]. 5. Route the display cable through the routing guides on the palmrest and keyboard assembly [2].
6. Affix the antenna cables to the system board [1]. 7. Connect the display cable to the connector on the system board [2].
Next steps 1. 2. 3. 4. 5. Replace the WLAN. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Osłona wyświetlacza Wymontowywanie oprawy wyświetlacza Wymagania 1. 2. 3. 4. 5. 6. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj kartę pamięci SD. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj kartę sieci WLAN. Wymontuj zestaw wyświetlacza. Kroki 1.
3. Zdejmij osłonę z zestawu wyświetlacza.
Instalowanie osłony wyświetlacza Kroki 1. Dopasuj osłonę wyświetlacza do tylnej pokrywy wyświetlacza.
2. Delikatnie wciśnij osłonę wyświetlacza na miejsce.
Kolejne kroki 1. 2. 3. 4. 5. 6. Zainstaluj zestaw wyświetlacza Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Panel wyświetlacza Wymontowywanie panelu wyświetlacza Wymagania 1. 2. 3. 4. 5. 6. 7. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj kartę pamięci SD. Wymontuj pokrywę dolną. Wymontuj akumulator.
3. Odklej taśmę mocującą kabel wyświetlacza do tyłu panelu wyświetlacza [1]. 4. Otwórz zatrzask i odłącz kabel wyświetlacza od złącza kabla panelu wyświetlacza [2]. 5. Wyjmij panel wyświetlacza z pokrywy tylnej wyświetlacza [3].
UWAGA Nie ciągnij ani nie odrywaj taśmy elastycznej od panelu wyświetlacza. Nie ma potrzeby oddzielać wsporników od panelu. 6. Po wykonaniu powyższych czynności pozostaje panel wyświetlacza.
Instalowanie panelu wyświetlacza Kroki 1. Połóż panel wyświetlacza na płaskiej i czystej powierzchni.
2. Podłącz kabel wyświetlacza do złącza z tyłu panelu wyświetlacza i zamknij zaczep, aby zamocować kabel [1]. 3. Przyklej taśmę mocującą kabel wyświetlacza do tyłu panelu wyświetlacza [2]. 4. Odwróć panel wyświetlacza i umieść go na tylnej pokrywie wyświetlacza [3].
5. Dopasuj otwory na śruby w panelu wyświetlacza do otworów w pokrywie tylnej wyświetlacza [1]. 6. Wkręć sześć śrub (M2x2) i dwie śruby (M2x3) mocujące panel wyświetlacza do pokrywy tylnej wyświetlacza [2].
Kolejne kroki 1. 2. 3. 4. 5. 6. 7. Zainstaluj osłonę wyświetlacza. Zainstaluj zestaw wyświetlacza Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Kabel wyświetlacza Wymontowywanie kabla wyświetlacza Wymagania 1. 2. 3. 4. 5. 6. 7. 8. 92 Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wymontuj kartę pamięci SD. Wymontuj pokrywę dolną.
Kroki 1. Wyjmij kabel kamery i kabel wyświetlacza z prowadnic w pokrywie tylnej wyświetlacza [1, 2]. 2. Odklej taśmę mocującą kabel kamery [3]. 3. Wyjmij kabel kamery i kabel wyświetlacza z zestawu tylnej pokrywy wyświetlacza.
Instalowanie kabla wyświetlacza Kroki 1. Umieść kabel wyświetlacza i kabel kamery w tylnej pokrywie wyświetlacza.
2. Umieść kabel wyświetlacza i kabel kamery w prowadnicach na zestawie pokrywy wyświetlacza i anteny [1, 2]. 3. Przyklej taśmę mocującą kabel kamery [3].
Kolejne kroki 1. 2. 3. 4. 5. 6. 7. 8. Zainstaluj panel wyświetlacza. Zainstaluj osłonę wyświetlacza. Zainstaluj zestaw wyświetlacza Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Złącze zasilacza Removing the power adapter port Prerequisites 1. 2. 3. 4. 5.
Instalowanie gniazda zasilacza Kroki 1. Umieść gniazdo zasilacza we wnęce w zestawie podparcia dłoni i klawiatury [1]. 2. Wkręć śrubę (M2x3) mocującą gniazdo zasilacza do zestawu podparcia dłoni i klawiatury [2]. 3. Podłącz kabel gniazda zasilacza do płyty systemowej [3, 4].
Kolejne kroki 1. 2. 3. 4. 5. Zainstaluj kartę sieci WLAN. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę pamięci SD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Kamera Removing the camera Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. Follow the procedure in before working inside your computer Remove the SD memory card Remove the base cover Remove the battery Remove the WLAN Remove the display assembly Remove the display bezel Remove the display panel Steps 1.
Follow the below procedure to remove the camera in systems with the Touch functionality. 4. Peel the tape that secures the camera off the display back-cover [1]. 5. Lift the camera module from the display back-cover [2].
Installing the camera Steps 1. Connect the camera cable to the camera module [1]. 2. Route the camera cable through the routing channels [2]. 3. Using the alignment post, adhere the camera module on the display back-cover [3].
Following is the procedure to install the camera in systems with the Touch functionality. 4. Align and replace the camera module on the display back-cover [1]. 5. Adhere the tape that secures the camera off the display back-cover [2].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. Replace the display panel. Replace the display bezel. Replace the display assembly. Replace the WLAN. Replace the battery. Replace the base cover. Replace the SD memory card. Follow the procedure in after working inside your computer. Zestaw podparcia dłoni i klawiatury Removing the palmrest and keyboard assembly Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9.
10. 11. 12. 13. 14. 15. 16. 17. Remove the touch pad assembly Remove the VGA daughter board Remove the power button board Remove the speakers Remove the system fan Remove the heatsink Remove the system board Remove the display assembly About this task After performing the preceding steps, you are left with the palmrest and keyboard assembly. NOTE: The power button board is not included with the service replacement palmrest assembly.
5 Troubleshooting Program diagnostyczny ePSA (Enhanced Pre-Boot System Assessment) Informacje na temat zadania Test diagnostyczny ePSA obejmuje pełną kontrolę elementów sprzętowych. Test ePSA jest wbudowany w systemie BIOS i uruchamiany wewnętrznie przez system BIOS. Wbudowana diagnostyka systemu zawiera szereg opcji dotyczących określonych urządzeń i grup urządzeń, które umożliwiają: Test diagnostyczny ePSA można zainicjować, naciskając klawisze Fn+PWR podczas włączania komputera.
Diagnostyka Tabela 5. Diagnostyka M-BIST L-BIST Przeznaczenie narzędzia diagnostycznego Ocenia stan płyty systemowej w celu dokładniejszego ustalenia przyczyn braku zasilania, braku testu POST lub braku obrazu, co pomaga uniknąć ponownego wysyłania części. Sprawdza, czy płyta systemowa dostarcza zasilanie do wyświetlacza LCD, wykonując test szyny zasilania LCD, co umożliwia izolację przyczyn braku sygnału wideo do obrębu płyty głównej, ekranu LCD lub kabla.
NOTE: The diagnostic pattern consists of a two-digit number being represented by a first group of LED blinks (1–9) in amber, followed by a 1.5 s pause with the LED off, and then a second group of LED blinks (1–9) in white. This is then followed by a three second pause, with the LED off, before repeating over again. Each LED blink takes 0.5 s. The system will not shut down when displaying the Diagnostic Error Codes. Diagnostic Error Codes always supersede any other use of the LED.
• • • S0 (WŁĄCZONY) — system jest włączony. S4 — system zużywa najmniej energii w porównaniu ze wszystkimi innymi stanami uśpienia. System jest prawie w stanie WYŁĄCZONY, spodziewaj się poboru prądu. Dane kontekstowe są zapisane na dysku twardym. S5 (WYŁĄCZONY) — system jest w stanie wyłączenia.
6 Uzyskiwanie pomocy Kontakt z firmą Dell Wymagania UWAGA W przypadku braku aktywnego połączenia z Internetem informacje kontaktowe można znaleźć na fakturze, w dokumencie dostawy, na rachunku lub w katalogu produktów firmy Dell. Informacje na temat zadania Firma Dell oferuje kilka różnych form obsługi technicznej i serwisu, online oraz telefonicznych. Ich dostępność różni się w zależności od produktu i kraju, a niektóre z nich mogą być niedostępne w regionie użytkownika.