Dell Latitude 3500 Servicemanual Forordningsmodel: P86F Forordningstype: P86F001 Maj 2021 rev.
Bemærk, forsigtig og advarsel BEMÆRK: En NOTE angiver vigtige oplysninger, som hjælper dig med at bruge computeren bedre. FORSIGTIG: FORSIGTIG angiver enten en mulig beskadigelse af hardware eller tab af data, og oplyser dig om, hvordan du kan undgå dette problem. ADVARSEL: ADVARSEL angiver risiko for tingskade, legemsbeskadigelse eller død. © 2019 - 2021 Dell Inc. eller dets associerede selskaber. Alle rettigheder forbeholdes. Dell, EMC, og andre varemærker er varemærker tilhørende Dell Inc.
Indholdsfortegnelse Kapitel 1: Sådan arbejder du med computeren................................................................................... 5 Sikkerhedsinstruktioner.........................................................................................................................................................5 Sådan slukker du for computeren — Windows 10............................................................................................................
Håndfladestøtte og tastaturmodul............................................................................................................................ 109 Kapitel 5: Fejlfinding..................................................................................................................... 111 Enhanced Pre-Boot System Assessment – ePSA-diagnosticering.............................................................................. 111 Kørsel af ePSA-diagnosticeringen..................................
1 Sådan arbejder du med computeren Sikkerhedsinstruktioner Forudsætninger Følg sikkerhedsinstruktionerne med henblik på din egen sikkerhed og for at beskytte computeren og arbejdsmiljøet mod mulige skader. Hvis intet andet er angivet bygger hver fremgangsmåde i dette dokument på følgende forudsætninger: ● Du har læst sikkerhedsoplysningerne, som fulgte med computeren. ● En komponent kan genmonteres eller, hvis købt separat, installeres ved at udføre fjernelsesproceduren i omvendt rækkefølge.
BEMÆRK: Sørg for, at computeren og alle tilsluttede enheder er slukket. Hvis computeren og de tilsluttede enheder ikke blev slukket automatisk, da du lukkede operativsystemet, skal du trykke på tænd/sluk-knappen i ca. 6 sekunder for at slukke dem. Før du udfører arbejde på computerens indvendige dele Om denne opgave For at undgå skader på din computer, skal du udføre de følgende trin, inden du får i gang med at arbejde inde i computeren. Trin 1. Sørg for, at du følger Sikkerhedsinstruktionerne. 2.
2 Teknologi og komponenter DDR4 DDR4-hukommelse (Double Data Rate – fjerde generation) er en efterfølger til DDR2- og DDR3-teknologierne, som har højere hastigheder og op til 512 GB i kapacitet, sammenlignet med maksimumkapaciteten for DDR3 på 128 GB pr. DIMM. DDR4 SDRAM (Synchronous Dynamic Random-Access Memory) er affaset anderledes end både SDRAM og DDR for at forhindre brugeren i at installere den forkerte type hukommelse i systemet.
Figur 3. Buet kant Hukommelsesfejl Hukommelsesfejl i systemet viser den nye fejlkode ON-FLASH-FLASH eller ON-FLASH-ON. Hvis al hukommelse fejler, tænder LCD ikke. Fejlfind for muligt hukommelsessvigt ved at afprøve kendte gode hukommelsesmoduler i hukommelsesstikkene på bunden af systemet eller under tastaturet, som i nogle bærbare systemer. BEMÆRK: DDR4-hukommelsen sidder i kortet og er ikke en udskiftelig DIMM, som vist og refereret til.
Hastighed Aktuelt er der 3 hastighedstilstande defineret i de seneste USB 3.0/USB 3.1 Gen 1-specifikationer. Disse er Super-Speed (Superhastighed), Hi-Speed (Højhastighed) og Full-Speed (Fuld hastighed). Den nye SuperSpeed-funktion har en overførselshastighed på 4,8 Gbps. Mens specifikationerne beholder Hi-Speed og Full-Speed USB-tilstandene, almindeligvis kendt som henholdsvis USB 2.0 og 1.
Kompatibilitet Den gode nyhed er, at USB 3.0/USB 3.1 Gen 1 er omhyggeligt planlagt til, fra starten, at kunne sameksistere fredeligt med USB 2.0. Da USB 3.0 specificerer nye fysiske tilslutninger, kræver det således nye kabler, der kan klare de højere hastigheder i den nye protokol. Selve stikket er det samme rektangulære stik med fire USB 2.0 kontakter, på eksakt samme placering som før. Fem nye tilslutninger der kan bære modtage- og senderetning og transmittere data uafhængigt er til stede i USB 3.
Tabel 2. Specifikationer for Intel Optane-hukommelse Funktion Specifikationer Grænseflade PCIe 3x2 NVMe 1.1 Stik M.2-kortslot (2230/2280) Understøttede konfigurationer ● 7. generation af Intel Core i3/i5/i7 processorer eller højere ● Windows 10 64-bit version eller højere ● Intel Rapid Storage Technology-driver version 15.9.1.1018 eller højere Kapacitet 32 GB eller 64 GB Aktivering af Intel Optane-hukommelse Trin 1. På proceslinjen, klik på søgefeltet, og indtast "Intel Rapid Storage Technology".
Tabel 3. Specifikationer for Intel UHD Graphics 620 (fortsat) Intel UHD-grafikkort 620 Estimeret maksimalt strømforbrug (TDP) 15 W (inkluderet i CPU-strøm) Overdækningsplaner Ja Operativsystemets grafik/ understøttelse af Video API DirectX 12 (Windows 10), OpenGL 4.5 Maksimal vertikal opdateringshastighed Op til 85 Hz afhængigt af opløsningen Understøttelse af flere skærme På systemet: eDP (internt), HDMI Via valgfri USB Type-C-port: VGA, DisplayPort Eksterne stik HDMI 1.
3 Større komponenter i dit system 1. Bunddæksel 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 14 WLAN-kort Hukommelsesmoduler Systemkort M.2 solid state-drev eller Intel Optane – Valgfri Batteri Håndfladestøttemodul Højttalere Pegefeltsmodul Skærmmodul Harddiskmodul IO-kort VGA-udvidelseskort Systemblæser Kølelegeme BEMÆRK: Dell leverer en komponentliste med de tilsvarende komponentnumre for den købte originale systemkonfiguration. Disse dele er tilgængelige i henhold til den garantidækning, som kunden har købt.
4 Sådan fjernes og installeres komponenter Anbefalet værktøj Procedurerne i dette dokument kræver følgende værktøj: ● Phillips #0 skruetrækker ● Phillips #1 skruetrækker ● Plastikpen BEMÆRK: Nr. 0 skruetrækkeren er til skruerne 0-1 og nr. 1 skruetrækkeren er til skruerne 2-4. Secure Digital-kort Fjernelse af Micro Secure Digital-kort Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Trin 1. Tryk på micro Secure Digital-kortet for at frigøre det fra computeren. 2.
Installation af micro Secure Digital-kortet Trin 1. Skub micro Secure Digital-kortet ind i dets slot, indtil det klikker på plads. 2. Følg procedurerne i Efter du har udført arbejde på computerens indvendige dele.
Bunddæksel Sådan fjernes bunddækslet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern SD-hukommelseskortet Trin 1. Løsn de ti fastmonterede skruer, der fastgør bunddækslet til håndfladestøtten og tastaturmodulet.
2. Lirk bunddækslet af, og fortsæt med af åbne højre side af bunddækslet.
3. Løft bunddækslets højre side [1], og tag det af håndfladestøtten og tastaturmodulet [2].
Sådan installeres bunddækslet Trin 1. Placer bunddækslet på håndfladestøtten og tastaturmodulet [1].
2. Stram de ti fastmonterede skruer, der fastgør bunddækslet til håndfladestøtten og tastaturmodulet.
Næste trin 1. Genmonter SD-hukommelseskortet 2. Følg proceduren under Efter du har arbejde på computerens indvendige dele Batteri Forholdsregler for litium-ion-batteri FORSIGTIG: ● Vær forsigtig, når du håndterer lithium-ion-batterier. ● Aflad batteriet så meget som muligt, inden du fjerner det fra systemet. Dette kan gøres ved at koble vekselstrømsadapteren fra systemet for derved at få opbrugt batteriet. ● Man må ikke knuse, smide, beskadige batteriet eller stikke fremmedlegemer ind i det.
Sådan fjernes batteriet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern SD-hukommelseskortet 3. Fjern bunddækslet Trin 1. Frakobl batteriet fra systemkortet. 2. Fjern de fire (M2x3) skruer, der fastgør batteriet til håndfladestøtten og tastaturmodulet [1]. 3. Løft batteriet op fra håndfladestøtten og tastaturmodulet [2].
Sådan installeres batteriet Trin 1. Flugt batteriets skruehuller med håndfladestøttens og tastaturmodulets skruehuller [1]. 2. Genmonter de fire (M2x3) skruer, der fastgør batteriet til håndfladestøtten og tastaturmodulet [2].
3. Tilslut batterikablet til systemkortet.
Næste trin 1. Genmonter bunddækslet 2. Genmonter SD-hukommelseskortet 3. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Harddisk Sådan fjernes harddiskmodulet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet. Trin 1. Kobl kablet til systemblæseren fra systemkortet [1]. 2. Pil tapen af, der fastgør harddiskkablet til håndfladestøtte- og tastaturmodulet [2].
Sådan installeres harddiskmodulet Trin 1. Få skruehullerne på harddiskmodulet til at flugte med håndfladestøttens og tastaturmodulets skruehuller [1]. 2. Sæt de fire (M2x4) skrueri, der fastgør harddiskmodulet på håndfladestøtten og tastaturmodulet [2].
3. Sæt tapen på, der fastgør harddiskkablet til håndfladestøtte- og tastaturmodulet [1]. 4. Tilslut harddiskkablet til systemkortet [2].
Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele IO-kort Sådan fjernes IO-kortet Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Fjern harddiskmodulet. BEMÆRK: Påkrævet for systemer med batterier på 42 wattimer Trin 1.
Sådan installeres IO-kortet Trin 1. Anbring vha. styremærkerne I/O-kortet på håndfladestøtten og tastaturmodulet [1]. 2. Fjern de to (M2x3) skruer, der fastgør I/O-kortet til håndfladestøtten og tastaturmodulet [2].
3. Sæt I/O-kortkablet fast på håndfladestøtten og tastaturmodulet [1]. 4. Forbind I/O-kortets kabel til systemkortet, og luk låsen for at fastgøre kablet [2].
Næste trin 1. Genmonter harddiskmodulet. BEMÆRK: Påkrævet for systemer med batterier på 42 wattimer 2. 3. 4. 5. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Berøringsplade Sådan fjernes pegefeltsmodulet Forudsætninger BEMÆRK: Udelukkende til information. Pegefeltet følger med håndfladestøtten. 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
5. Fjern de fire M2x2-skruer, der fastgør pegefeltet til håndfladestøtte- og tastaturmodulet [1]. 6. Løft pegefeltet af håndfladestøtte- og tastaturmodulet [2].
Sådan installeres pegefeltmodulet Om denne opgave BEMÆRK: Sørg for, at pegefeltet flugter med de tilgængelige vejledere på håndfladestøtten og tastaturmodulet, så mellemrummet på begge sider af pegefeltet er det samme. Trin 1. Placer pegefeltet i dets slot på håndfladestøtten og tastaturmodulet [1]. 2. Genmonter de fire skruer (M2x2), der fastgør pegefeltet på håndfladestøtten og tastaturmodulet [2].
3. Sæt tapen på, der fastgør pegefeltet til håndfladestøtten og tastaturmodulet [1]. 4. Skub pegefeltets kabel ind i dets stik på systemkortet, og luk låsen for at fastgøre kablet [2].
5. Placer pegefeltets bøjle i dets slot på håndfladestøtten og tastaturmodulet [1]. 6. Genmonter de tre skruer (M2x2), der fastgør pegefeltets bøjle til håndfladestøtten og tastaturmodulet [2], og sæt tapen fast, der fastgør bøjlen til håndfladestøtten.
Næste trin 1. 2. 3. 4. Udskift batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Hukommelsesmoduler Sådan fjernes hukommelsesmodulet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet. Trin 1. Lirk klemmerne, der fastgør hukommelsesmodulet, indtil hukommelsesmodulet hopper op [1]. 2.
BEMÆRK: Hvis du ikke hører et klik, skal du fjerne hukommelsesmodulet og sætte det i igen. Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele SIM-kort Sådan fjernes SIM-kortet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Trin 1. Åbn låsen, der dækker SIM-kortets slot for at frigøre det fra systemet [1]. 2.
Sådan installeres SIM-kortet Trin 1. Åbn låsen, der dækker SIM-kortets slot for at frigøre det fra systemet [1]. 2. Sæt en nål ind i slotten, og tryk indad for at udskyde SIM-kortbakken [2]. 3. Træk i SIM-kortbakken, og anbring SIM-kortet i bakken [3] og [4]. 4. Skub SIM-kortbakken ind i slotten, indtil den klikker på plads.
5. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. WLAN-kort Sådan fjernes WLAN-kortet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet. Trin 1. Fjern den enkelte (M2x3) skrue, der fastgør WLAN-kortbøjlen til systemkortet [1]. 2. Skub og fjern WLAN-kortets bøjle, som fastgør WLAN-kablerne [2]. 3. Kobl WLAN-kablerne fra stikkene på WLAN-kortet [3]. 4.
Sådan installeres WLAN-kortet Om denne opgave FORSIGTIG: For at undgå at beskadige WLAN-kortet må du ikke placere kabler under det. Trin 1. Indsæt WLAN-kortet i stikket på systemkortet [1]. 2. Slut WLAN-kablerne til stikkene på WLAN-kortet [2]. 3. Placer bøjlen for WLAN-kortet for at fastgøre WLAN-kablerne til WLAN-kortet [3]. 4. Genmonter skruen (M2x3), der fastgør WLAN-bøjlen til WLAN-kortet [4].
Næste trin 1. 2. 3. 4. Frakobl batterikablet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele WWAN-kort Sådan fjernes WWAN-kortet Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern SIM-kortet. Fjern bunddækslet Frakobl batterikablet. Trin 1. Fjern den enkelte M2x3-skrue, der fastgør WWAN-kortbøjlen til WWAN-kortet [1]. 2.
Sådan installeres WWAN-kortet Om denne opgave FORSIGTIG: For at undgå skader på WWAN-kortet må der ikke anbringes kabler under det. Trin 1. Indsæt WWAN-kortet i stikket på WWAN-udvidelseskortet [1]. 2. Tilslut WWAN-kablerne til stikkene på WWAN-kortet [2]. 3. Anbring WWAN-kortets bøjle for at fastgøre WWAN-kablerne til WWAN-kortet [3]. 4. Genmonter den ene M2x3-skrue for at fastgøre WWAN-bøjlen til WWAN-kortet [4].
Næste trin 1. 2. 3. 4. 5. Monter batteri-kablet. Genmonter bunddækslet. Genmonter SIM-kortet Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele WWAN-udvidelseskort Sådan fjernes WWAN-udvidelseskortet Forudsætninger 1. 2. 3. 4. 5. 6. 44 Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern SIM-kortet. Fjern bunddækslet. Frakobl batterikablet. Fjern WWAN-kortet.
Trin 1. Åbn låsen og frakobl WWAN-udvidelseskortets kabel fra WWAN-udvidelseskortet.
2. Fjern de to M2x3-skruer, der fastgør WWAN-udvidelseskortet til håndfladestøtte- og tastaturmodulet [1], og løft derefter WWAN udvidelseskortet væk fra håndfladestøtte- og tastaturmodulet [2]. Sådan installeres WWAN-udvidelseskortet Om denne opgave FORSIGTIG: For at undgå skader på WWAN-kortet må der ikke anbringes kabler under det. Trin 1. Anvend styremærkerne til at placere WWAN-kortet på håndfladestøtte- og tastaturmodulet [1] 2.
3. Sæt WWAN-udvidelseskortets kabel til stikket på WWAN-udvidelseskortet, og luk låsen for at fastgøre kablet [1].
Næste trin 1. 2. 3. 4. 5. 6. Genmonter WWAN-kortet Monter batteri-kablet. Genmonter bunddækslet. Genmonter SIM-kortet Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Solid-state-drev/Intel Optane-hukommelsesmodul Sådan fjernes M.2 2280 solid state-drev eller Intel Optane – Valgfri Forudsætninger BEMÆRK: Deaktiver Intel Optane-hukommelsen, før du fjerner Intel Optane-hukommelsesmodulet fra din computer.
4. Fjern den ene M2x2-skrue, der fastgør solid-state-drevet/Intel Optane-kortet til håndfladestøtte- og tastaturmodulet [1. 5. Skub og løft solid state-drevet/Intel Optane-kortet af håndfladestøtte- og tastaturmodulet [2].
Sådan installeres M.2 2280 solid state-drev eller Intel Optane - Valgfri Trin 1. Skub og indsæt tappen på solid state-drevet/Intel Optane-kortet i slotten for solid state-drevet/Intel Optane-kortet [1]. 2. Genmonter den ene M2x2-skrue, der fastgør solid state-drevet/Intel Optane-kortet til håndfladestøtte- og tastaturmodulet [2]. 3. Tilpas og genmonter den termiske plade på slotten til solid state-drevet/Intel Optane-kortet [1,2]. 4.
Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Sådan fjernes M.2 solid-state-drevbeslaget Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet Trin 1. Fjern M2x3-skruen, der fastgør solid state-drevbeslaget til håndfladestøtte- og tastaturmodulet [1]. 2.
Sådan installeres solid-state-drevbeslaget Trin 1. Anbring og genmonter solid-state-drevbeslaget på håndfladestøtte- og tastaturmodulet [1]. 2. Genmonter M2x3-skruen, der fastgør solid-state-drevets beslag til håndfladestøtte- og tastaturmodulet [2].
Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Sådan fjernes M.2 2230 solid-state-drevet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet Trin 1. Fjern den enkelte M2x3-skrue, der fastgør den termiske plade til håndfladestøtte- og tastaturmodulet [1]. 2.
4. Fjern M2x2-skruen, som fastgør solid-state-drevet til solid-state-drevets beslag [1]. 5. Træk i solid-state-drevet, og fjern det fra solid-state-drevets slot [2].
Sådan installeres M.2 2230 solid-state-drevet Trin 1. Sæt solid-state-drevet ind i solid-state-drevets slot på systemkortet [1]. 2. Genmonter M2x3-skruen, der fastgør solid-state-drevet til solid-state-drevets beslag [2].
3. Tilpas og genmonter den termiske plade på solid state-drevet [1,2]. 4. Genmonter (M2x3) skruen, der fastgør kølepladen til håndfladestøtten og tastaturmodulet [3].
Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Højttalere Sådan fjernes højtalerne Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batterikablet. Trin 1. Frakobl højtalerkablet fra systemkortet [1]. 2.
4. Løft højttalerne og dets kabel af håndfladestøtte- og tastaturmodulet.
Sådan installeres højttalerne Om denne opgave BEMÆRK: Hvis gummimanchetterne skubbes ud, når højttalerne fjernes, skal de skubbes tilbage, før højtalerne genmonteres. Trin 1. Brug styremærkerne og gummimanchetterne til at anbringe højtalerne i åbningerne på håndfladestøtte- og tastaturmodulet .
2. Før højttalerkablet gennem håndfladestøtte- og tastaturmodulets kabelkanaler [1]. 3. Klæb tapen fast, der fastgør højtalerkablerne til håndfladestøtte- og tastaturmodulet [2]. 4. Tilslut højttalerkablet til systemkortet [3].
Næste trin 1. 2. 3. 4. Udskift batterikablet. Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Systemblæser Sådan fjernes systemblæseren Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Trin 1. Kobl VGA-kortets kabel [1] og skærmkablet [2, 3] fra systemkortet.
2. Frigør VGA-kortkablet fra kabelkanalerne på blæseren [1]. 3. Kobl blæserkablet fra systemkortet [2]. 4. Fjern de to (M2x3) skruer, der fastgør blæseren til håndfladestøtten og tastaturkortmodulet [1].
5. Løft blæseren op fra håndfladestøtten og tastaturkortmodulet [2]. Sådan installeres systemblæseren Trin 1. Få skruehullerne på blæseren til at flugte med skruehullerne på håndfladestøtten og tastaturmodulet [1]. 2. Genmonter de to M2x3-skruer i, der fastgør blæseren til håndfladestøtte- og tastaturmodulet [2].
3. Før VGA-kortets kabel og skærmkablet gennem kabelkanalerne på blæseren [1]. 4. Tilslut blæserkablet til systemkortet [2].
5. Tilslut VGA-kortets kabel [1] og skærmkablet [2, 3] til systemkortet. Næste trin 1. 2. 3. 4. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Varme-sink Sådan fjernes kølelegemet – UMA Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Trin 1.
Sådan installeres kølelegemet - UMA Trin 1. Placer kølelegemet på systemkortet, og få skruehullerne på kølelegemet til at flugte med skruehullerne på systemkortet [1]. 2. Spænd de fire fastmonterede skruer, der fastgør kølelegemet til systemkortet i rækkefølge (som angivet på kølelegemet) [2]. Næste trin 1. 2. 3. 4.
2. Løft kølelegemet af systemkortet [2]. Sådan installeres kølelegemet - separat Trin 1. Placer kølelegemet på systemkortet, og få skruehullerne på kølelegemet til at flugte med skruehullerne på systemkortet [1]. 2. Spænd de fire fastmonterede skruer, der fastgør kølelegemet til systemkortet i rækkefølge (som angivet på kølelegemet) [2].
Næste trin 1. 2. 3. 4. Udskift batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren i Efter du har udført arbejde på computerens indvendige dele VGA-udvidelseskort Sådan fjernes VGA-udvidelseskortet Forudsætninger 1. 2. 3. 4. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Trin 1. Frakobl VGA-udvidelseskortets kabel [1] og skærmkablet fra systemkortet [2, 3].
2. Frigør VGA-kortkablet fra kabelkanalerne på blæseren. 3. Sæt de to skruer (M2x3) skruer i, der fastgør VGA-datterkortet til håndfladestøtten og tastaturmodulet [1]. 4. Løft VGA-udvidelseskortet væk fra systemet [2].
Sådan monteres VGA-udvidelseskortet Trin 1. Placer VGA-udvidelseskortet, og få skruehullerne på VGA-udvidelseskortet til at flugte med skruehullerne i håndledsstøtte- og tastaturmodulet [1]. 2. Genmonter de to skruer (M2x3), der fastgør VGA-udvidelseskortet til håndledsstøtte- og tastaturmodulet [2].
3. Før VGA-kortets kabel og skærmkablet gennem kabelkanalerne på blæseren. 4. Slut VGA-kortets kabel [1] og skærmkablet [2] til bundkortet.
Næste trin 1. 2. 3. 4. Genmonter batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har udført arbejde på computerens indvendige dele Strømknapkort Fjernelse af tænd/sluk-knapkortet med valgfri fingeraftrykslæser Forudsætninger 1. 2. 3. 4. 5. 6. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Fjern systemblæseren. Fjern skærmmodulet. Trin 1.
3. Fjern de to M2x3-skruer, der fastgør tænd/sluk-knappens kort til håndfladestøtte- og tastaturmodulet [1]. 4. Løft tænd/sluk-knappens kort og dets kabel af håndfladestøtte- og tastaturmodulet [2].
Sådan installeres tænd/sluk-knappen med den valgfri fingeraftrykslæser Trin 1. Placer strømknapkortet i dets slot på håndfladestøtten og tastaturmodulet [1]. 2. Genmonter de to (M2x3) skruer, der fastgør tænd/sluk-knappens kort til håndfladestøtten og tastaturmodulet [2]. 3. Sæt tænd/sluk-knappens kabel fast på håndfladestøtten og tastaturmodulet [1]. 4. Skub tænd/sluk-knappens og fingeraftryksaflæserens kabel på systemkortet, og luk låsen for at fastgøre kablet [2].
Næste trin 1. 2. 3. 4. 5. 6. Genmonter skærmmodulet. Genmonter systemblæseren. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Systemkort Sådan fjernes systemkortet Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet. Fjern bunddækslet. Fjern batteriet. Fjern WLAN. Fjern hukommelsen. Fjern SSD'et.
a. b. c. d. e. f. Strømknapkort [1]. Fingeraftrykslæser (valgfrit tilbehør) [2]. IO-kort [3]. HDD [4]. Pegefelt [5]. Tastatur [6]. 2. Fjern følgende kabler fra systemkortet: a. DC-indgang [1, 2]. b. Højtaler [3].
3. Fjern de to M2x3- og de to M2x2-skruer, der fastgør systemkortet til håndfladestøtte- og tastaturmodulet [1]. 4. Løft systemkortet op fra håndfladestøtten og tastaturmodulet [2].
Sådan installeres systemkortet Trin 1. Flugt systemkortets skruehul med håndfladestøttens og tastaturmodulets skruehul [1]. 2. Genmonter de to M2x3- og to M2x2-skruer, der fastgør systemkortet til håndfladestøtte- og tastaturmodulet [2].
3. Tilslut følgende kabler til systemkortet: a. DC-indgang [1, 2]. b. Højtaler [3].
4. Tilslut følgende kabler til systemkortet: a. b. c. d. e. f. 80 Strømknapkort [1]. Fingeraftrykslæser (valgfrit tilbehør) [2]. IO-kort [3]. HDD [4]. Pegefelt [5]. Tastatur [6].
Næste trin 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Genmonter skærmmodulet. Genmonter kølelegemet. Genmonter systemblæseren. Genmonter SSD’en. Genmonter hukommelsen Genmonter WLAN’en. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Skærmmodul Sådan fjernes skærmmodulet Forudsætninger 1. 2. 3. 4. 5. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet.
3. Frigør skærmkablet fra kabelkanalerne i håndfladestøtten og tastaturmodulet [1]. 4. Fjern de fire M2.5x5-skruer, der fastgør venstre og højre hængsler til systemkortet samt hånddladestøtte- og tastaturmodulet [2].
5. Løft håndfladestøtte- og tastaturmodulet skråt [1]. 6. Fortsæt med at løfte håndfladestøtte- og tastaturmodulet, indtil det går fri af hængslerne [2].
7. Træk og fjern håndfladestøtte- og tastaturmodulet af skærmmodulet.
8. Efter udførelse af alle foregående trin har du skærmmodulet tilbage.
Sådan installeres skærmmodulet Om denne opgave BEMÆRK: Sørg for, at hængslerne åbnes til maks. position, før skærmmodulet genmonteres på håndfladestøtten og tastaturmodulet. Trin 1. Flugt og placer håndfladestøtten og tastaturmodulet under hængslerne på skærmmodulet.
2. Sæt håndfladestøtte- og tastaturmodulet på plads på skærmmodulet [1]. 3. Tryk hængslerne ned på systemkortet samt håndfladestøtten og tastaturmodulet [2].
4. Før skærmkablet igennem håndfladestøtte- og tastaturmodulets kabelkanaler [1]. 5. Genmonter de fire (M2,5x5) skruer, der fastgør venstre og højre hængsler til systemkortet samt håndfladestøtten og tastaturmodulet [2].
6. Tilslut den trådløse antennes kabler, og sæt tapen fast, som fastgør dem til systemkortet [1]. 7. Tilslut skærmkablet til stikket på systemkortet [2, 3].
Næste trin 1. 2. 3. 4. 5. Genmonter WLAN’en. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele Skærmfacet Sådan fjernes skærmrammen Forudsætninger 1. 2. 3. 4. 5. 6. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Frakobl batteriet Fjern WLAN Fjern skærmmodulet Trin 1.
FORSIGTIG: Løft forsigtigt rammen, da den er fastgjort til skærmmodulet med et stærkt klæbemiddel. 3. Løft rammen af skærmmodulet.
Sådan monteres skærmrammen Trin 1. Juster skærmrammen efter skærmens bagdæksel.
2. Klik forsigtigt skærmrammen på plads.
Næste trin 1. 2. 3. 4. 5. 6. Genmonter skærmmodulet Genmonter WLAN Tilslut batteriet igen Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har udført arbejde på computerens indvendige dele Skærmpanel Sådan fjernes skærmpanelet Forudsætninger 1. 2. 3. 4. 5. 6. 7. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Fjern SD-hukommelseskortet Fjern bunddækslet Fjern batteriet Fjern WLAN Fjern skærmmodulet Fjern skærmfacetten Trin 1.
5. Løft skærmpanelet ud af skærmens bagdæksel [3]. BEMÆRK: Træk og fjern ikke Stretch-tapestykkerne (SR) fra skærmpanelet. Der er ikke behov for at adskille bøjlerne fra skærmpanelet. 6. Efter udførelse af alle ovennævnte trinnene er der kun skærmmodulet tilbage.
Sådan installeres skærmpanelet Trin 1. Placer skærmpanelet på en ren plan overflade.
2. Tilslut skærmkablet til stikket bagpå skærmpanelet, og luk låsen for at fastgøre kablet [1]. 3. Påsæt tapen, der fastgør skærmkablet til bagsiden af skærmpanelet [2]. 4. Vend skærmpanelet om, og anbring det forsigtigt på skærmens bagdæksel [3].
5. Ret skruehullerne i skærmpanelet ind med skruehullerne i skærmens bagdæksel og antennemodulet [1]. 6. Genmonter de fire (M2x2,5) skruer, der fastgør skærmpanelet til skærmens bagdæksel [2].
Næste trin 1. 2. 3. 4. 5. 6. 7. Genmonter skærmfacetten Genmonter skærmmodulet Genmonter WLAN Udskift batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Skærmhængsler Sådan fjernes skærmhængslerne Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
Sådan monteres skærmhængslerne Trin 1. Ret skruehullerne på hængslerne og beslagene ind med skruehullerne i skærmens bagdæksel og antennemodul [1]. 2. Genmonter de seks skruer (M2,5x2,5) og de to skruer (M2x2,5), der fastgør hængslerne til skærmens bagdæksel [2].
Næste trin 1. 2. 3. 4. 5. 6. 7. 8. Genmonter skærmpanelet Genmonter skærmfacetten Genmonter skærmmodulet Genmonter WLAN Udskift batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har udført arbejde på computerens indvendige dele Skærmkabel Sådan fjernes skærmkablet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. 2. Fjern SD-hukommelseskortet 3.
4. 5. 6. 7. 8. Fjern batteriet Fjern WLAN Fjern skærmmodulet Fjern skærmfacetten Fjern skærmpanelet Trin 1. Fjern kamerakablet og skærmkablet fra kabelkanalerne på skærmens bagdæksel og antennemodulet [1,2]. 2. Træk klæbemidlet af, der fastgør kamerakablet 3,4,5. 3. Løft kamerakablet og skærmkablet væk fra skærmens bagdæksel.
Sådan installeres skærmkablet Trin 1. Placer skærmkablet og kamerakablet på skærmens bagdæksel.
2. Før skærmkablet og kamerakablet igennem kabelkanalerne på skærmens bagdæksel og antennemodul [1,2]. 3. Sæt klæbemidlet på, der fastgør kamerakablet [3,4,5].
Næste trin 1. 2. 3. 4. 5. 6. 7. 8. Genmonter skærmpanelet Genmonter skærmfacetten Genmonter skærmmodulet Genmonter WLAN Udskift batteriet Genmonter bunddækslet Genmonter SD-hukommelseskortet Følg proceduren under Efter du har arbejde på computerens indvendige dele Kamera Sådan fjernes kameraet Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
Trin 1. Brug en plastikpen til forsigtigt at lirke kameraet af skærmens bagdæksel og antennemodulet [1]. 2. Frakobl kamerakablet fra kameramodulet [2]. 3. Løft kameramodulet op fra skærmens bagdæksel og antennemodulet [3]. Følg nedenstående procedure til at fjerne kameraet i systemer med touchfunktionalitet. 4. Pil tapen af, der fastgør kameraet på skærmens bagdæksel [1]. 5. Løft mikrofon-kameramodulet op fra skærmmodulet [2].
Sådan monteres kameraet Trin 1. Tilslut kamerakablet til kameramodulet [1]. 2. Før eDP-kablet gennem kabelkanalen [2]. 3. Brug styremærkerne til at sætte kameramodulet fast på skærmens bagdæksel og antennemodulet [3].
Følgende procedure er til montering af kameraet i systemer med touchfunktionalitet. 4. Anbring og genmonter kameramodulet på skærmens bagdæksel [1]. 5. Påsæt tapen, der fastgør kameraet på skærmens bagdæksel [2].
Næste trin 1. 2. 3. 4. 5. 6. 7. 8. Genmonter skærmpanelet. Genmonter skærmrammen. Genmonter skærmmodulet. Genmonter WLAN’en. Genmonter batteriet. Genmonter bunddækslet. Genmonter SD-hukommelseskortet. Følg proceduren i Efter du har udført arbejde på computerens indvendige dele. Håndfladestøtte og tastaturmodul Sådan fjernes håndfladestøtten og tastaturmodulet Forudsætninger 1. 2. 3. 4. 5. 6. 7. 8. 9. Følg proceduren i Før du udfører arbejde på computerens indvendige dele.
10. 11. 12. 13. 14. 15. 16. 17. Sådan fjernes pegefeltsmodulet Sådan fjernes VGA-udvidelseskortet. Fjern strømknapkortet Fjern højtalerne Fjern systemblæseren Fjern kølelegemet Fjern systemkortet Fjern skærmmodulet Om denne opgave Efter at have udført de foregående trin, står du tilbage med håndfladestøtten og tastaturmodulet. BEMÆRK: Tænd/sluk-knappens kort følger ikke med håndfladestøttemodulet (servicereservedel).
5 Fejlfinding Enhanced Pre-Boot System Assessment – ePSAdiagnosticering Om denne opgave ePSA-diagnostik (også kendt som systemdiagnostik) udfører et fulstændigt tjek af din hardware. ePSA er indlejret med BIOS og er lanceret af BIOS internt. Den indlejrede systemdiagnostik leverer en række muligheder til særlige enheder eller enhedsgrupper, der tillader dig at: ePSA-diagnostik kan startes ved hjælp af knapperne FN+PWR, mens computeren startes op.
Diagnostics (Diagnosticering) Tabel 5. Diagnostics (Diagnosticering) M-BIST L-BIST Diagnosticeringsværtøjets formål Evaluerer sundhedstilstanden af systemkortet for at få yderligere løsninger på symptomerne "No Power", "No Post" og "No Video" samt at reducerer gentagne rapporteringer. Kontrollerer, om systemkortet forsyner LCD-skærmen med strøm ved at udfører LCD-strømskinnetest, der kan isolere symptomet "No Video" til bundkortet, LCDskærmen eller kablet.
I stedet for bip-koder indikeres fejl med den tofarvede batteriopladnings-/status-LED. Et specifikt blinkende mønster følges af et mønster af blink i ravgul fulgt af hvid. Mønsteret gentages så. BEMÆRK: Det diagnostiske mønster består at et tocifret tal, som repræsenteres af den første gruppe af ravgule LED-blink (1-9), der efterfølges af en 1,5 sekunds pause med slukket LED og derefter en anden gruppe af hvide LED-blink (1-9).
Tabel 7. Batteristatus LED (fortsat) Strømkilde LED-adfærd Strømtilstand for systemet Batteriopladningsniveau Batteri Off (Fra) S0 > 10% Batteri Off (Fra) S4/S5 0-100% ● S0 (ON) — Systemet tændt ● S4— Systemet forbruger mindst strøm i forhold til alle andre dvaletilstande. Systemet er næsten i en OFF-tilstand, bortset fra en sivestrøm. Kontekstdata registreres på harddisk. ● S5 (OFF) — Systemet er i nedlukningstilstand.
6 Sådan får du hjælp Kontakt Dell Forudsætninger BEMÆRK: Hvis du ikke har en aktiv internetforbindelse, kan du finde kontaktoplysninger på købskvitteringen, pakkeslippen, fakturaen eller i Dells produktkatalog. Om denne opgave Dell giver flere muligheder for online- og telefonbaseret support og service. Tilgængeligheden varierer for de enkelte lande og produkter, og nogle tjenester findes muligvis ikke i dit område. Sådan kontakter du Dell omkring salg, teknisk support eller kundeservice: Trin 1.