Dell Latitude 3570 Sổ tay hướng dẫn chủ sở hữu Dòng máy điều chỉnh: P50F Dòng máy điều chỉnh: P50F001
Ghi chú, thận trọng và cảnh báo GHI CHÚ: GHI CHÚ cho biết thông tin quan trọng giúp cho việc sử dụng máy tính tốt hơn. THẬN TRỌNG: THẬN TRỌNG chỉ báo khả năng xảy ra hư hỏng phần cứng hoặc mất dữ liệu và cho bạn biết cách tránh được sự cố. CẢNH BÁO: CẢNH BÁO cho biết có thể có thiệt hại về tài sản, gây thương tích hoặc tử vong ở người. © 2016 2018 Dell Inc. hoặc các công ty con. Mọi quyền được bảo lưu. Dell, EMC và các nhãn hiệu khác là nhãn hiệu của Dell Inc. hoặc công ty con của Dell Inc.
Nội dung 1 Thao tác trên máy tính.................................................................................................................................6 Hướng dẫn an toàn.................................................................................................................................... 6 Trước khi thao tác bên trong máy tính........................................................................................................6 Tắt máy tính.........................................
Tháo cụm màn hình..................................................................................................................................23 Lắp đặt cụm màn hình.............................................................................................................................. 24 Tháo camera.............................................................................................................................................24 Lắp đặt camera...........................................
Thông số kỹ thuật bàn di chuột.................................................................................................................46 Thông số kỹ thuật pin............................................................................................................................... 46 Thông số kỹ thuật bộ chuyển đổi nguồn AC.............................................................................................47 Thông số kỹ thuật vật lý......................................................
1 Thao tác trên máy tính Hướng dẫn an toàn Sử dụng các hướng dẫn an toàn sau đây để giúp bảo vệ máy tính khỏi bị hư hại cũng như đảm bảo an toàn cá nhân của bạn. Trừ khi có lưu ý khác, mỗi quy trình trong tài liệu này giả định rằng đã có sẵn các điều kiện sau đây: • Bạn đã đọc thông tin an toàn đi kèm với máy tính của mình. • Một thành phần có thể được thay thế hoặc--nếu mua riêng--được lắp đặt bằng cách thực hiện quy trình tháo ra theo thứ tự ngược lại.
Tháo nắp. THẬN TRỌNG: Trước khi chạm vào bất cứ thứ gì bên trong máy tính, hãy nối đất bản thân bạn bằng cách chạm vào một bề mặt kim loại chưa sơn phủ, chẳng hạn như phần kim loại ở mặt sau máy tính. Trong khi thao tác, hãy thường xuyên chạm vào một bề mặt kim loại chưa sơn phủ để khử tĩnh điện có thể gây hư hại cho các thành phần bên trong. Tắt máy tính THẬN TRỌNG: Để tránh mất dữ liệu, hãy lưu và đóng mọi tập tin cũng như thoát khỏi tất cả các chương trình đang mở trước khi tắt máy tính.
2 Tháo và lắp các thành phần Phần này cung cấp thông tin chi tiết cách tháo và lắp đặt các thành phần từ máy tính của bạn. Công cụ được khuyên dùng Các quy trình trong tài liệu này yêu cầu các dụng cụ sau: • Tuốc-nơ-vít lưỡi dẹt loại nhỏ • Tuốc-nơ-vít Phillips #0 • Tuốc-nơ-vít Phillips #1 • Que nhựa mũi nhọn loại nhỏ Những điều cần thận trọng đối với pin Lithiumion THẬN TRỌNG: • Cẩn thận khi xử lý pin Lithium-ion.
Lắp đặt pin 1 Lắp pin vào trong khe cho đến khi khớp vào vị trí. 2 Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo nắp đế 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo pin. 3 Cách tháo nắp đế: a b Nới lỏng các vít cố định đang gắn nắp đế vào máy tính [1]. Sử dụng que nhựa mũi nhọn cạy nắp đế ra và tháo khỏi máy tính [2]. Lắp đặt nắp đế 1 Lắp lại nắp đế trên máy tính cho đến khi khớp vào vị trí. 2 Vặn các vít cố định để giữ chặt nắp đế vào máy tính.
Tháo bàn phím 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo pin. 3 Lật máy tính lên và mở màn hình để tiếp cận bàn phím. 4 Cách tháo bàn phím: a b Sử dụng que nhựa mũi nhọn tháo bàn phím khỏi các mép cạnh [1] và nhấc khỏi máy tính [2]. Nhả chốt và ngắt đấu nối dây cáp bàn phím ra khỏi các đầu nối trên bo mạch hệ thống [3, 4]. Lắp đặt bàn phím 1 Đấu nối dây cáp bàn phím vào các đầu nối trên bo mạch hệ thống.
Lắp đặt cụm ổ đĩa cứng 1 Lắp lại cụm ổ đĩa cứng vào trong khe trên máy tính. 2 Đấu nối cáp cụm ổ đĩa cứng vào đầu nối trên bo mạch hệ thống. 3 Vặn các vít để giữ chặt cụm ổ đĩa cứng vào máy tính. 4 Lắp đặt: a b 5 pin nắp đế Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo tấm đậy ổ đĩa cứng 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính.
Lắp đặt tấm đậy ổ đĩa cứng 1 Đấu nối cáp ổ đĩa cứng vào đầu nối trên ổ đĩa cứng. 2 Đặt tấm đậy ổ đĩa cứng lên ổ đĩa cứng để căn chỉnh các lỗ bắt vít trên cả hai mặt của ổ đĩa cứng. 3 Vặn các vít để giữ chặt tấm đậy ổ đĩa cứng vào ổ đĩa cứng. 4 Lắp đặt: a b c 5 cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo card WLAN 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính.
Tháo mô-đun bộ nhớ 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo: a b 3 pin nắp đế Cách tháo mô-đun bộ nhớ: a b Nhả các nẹp giữ ra khỏi mô-đun bộ nhớ cho đến khi mô-đun bộ nhớ bật lên [1]. Ngắt đấu nối mô-đun bộ nhớ khỏi đầu nối để tháo khỏi máy tính [2]. Lắp đặt mô-đun bộ nhớ 1 Lắp mô-đun bộ nhớ vào trong đầu nối và nhấn cho đến khi khớp vào vị trí. 2 Lắp đặt: a b 3 nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính.
4 Cách tháo chỗ dựa tay: a b c Mở màn hình và nhả chốt để ngắt đấu nối các dây cáp nút nguồn, đầu đọc dấu vân tay, bàn di chuột và đèn LED khỏi các đầu nối trên bo mạch hệ thống [1, 2]. Tháo các vít đang giữ chặt chỗ dựa tay vào máy tính [3]. Sử dụng que nhựa mũi nhọn nhả chỗ dựa tay khỏi các mép cạnh và tháo ra khỏi máy tính [4]. Lắp đặt chỗ dựa tay 1 Đặt chỗ dựa tay lên trên máy tính và nhấn dọc theo các mép cạnh cho tới khi khớp vào vị trí.
c d e f 3 cụm ổ đĩa cứng bàn phím chỗ dựa tay bo mạch hệ thống Cách tháo pin dạng đồng xu: a b Ngắt đấu nối dây cáp pin dạng đồng xu ra khỏi đầu nối trên bo mạch hệ thống. Nhấc lên và tháo pin dạng đồng xu ra khỏi lớp keo dính trên bo mạch hệ thống. Lắp đặt pin dạng đồng xu 1 Đặt pin dạng đồng xu vào trong ổ pin trên bo mạch hệ thống. 2 Đấu nối pin dạng đồng xu vào đầu nối trên bo mạch hệ thống.
Lắp đặt bo mạch USB 1 Đặt bo mạch USB vào trong khe trên máy tính. 2 Vặn con vít để giữ chặt bo mạch USB vào máy tính. 3 Đấu nối dây cáp bo mạch USB vào đầu nối trên bo mạch USB. 4 Lắp đặt: a b c d e 5 chỗ dựa tay bàn phím cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo bo mạch VGA 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính.
Lắp đặt bo mạch VGA 1 Đặt bo mạch VGA vào trong khe trên máy tính. 2 Đấu nối dây cáp bo mạch VGA vào đầu nối trên bo mạch VGA và đóng chốt. 3 Vặn con vít để giữ chặt bo mạch VGA vào máy tính. 4 Lắp đặt: a b c d e 5 chỗ dựa tay bàn phím cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo loa 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính.
b c d e 5 bàn phím cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo quạt hệ thống 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo: a b c d e 3 pin nắp đế cụm ổ đĩa cứng bàn phím chỗ dựa tay Cách tháo quạt hệ thống: a b c Ngắt đấu nối dây cáp quạt hệ thống khỏi đầu nối trên bo mạch hệ thống [1]. Tháo các vít đang giữ chặt quạt hệ thống vào máy tính [2]. Nhấc lên và tháo quạt hệ thống ra khỏi máy tính [3].
c d e 3 cụm ổ đĩa cứng bàn phím chỗ dựa tay Cách tháo dây cáp màn hình: a b c d Tháo con vít để nhả mấu kim loại đang giữ chặt dây cáp màn hình [1]. Nhấc mấu kim loại lên để tiếp cận dây cáp màn hình [2]. Lột lớp băng dính đang giữ chặt dây cáp màn hình [3]. Ngắt đấu nối dây cáp màn hình ra khỏi đầu nối trên bo mạch hệ thống [4]. Lắp đặt dây cáp màn hình 1 Đấu nối dây cáp màn hình vào đầu nối trên bo mạch hệ thống. 2 Dán lớp băng dính để giữ chặt dây cáp màn hình.
Lắp đặt cổng đầu nối nguồn 1 Lắp cổng đầu nối nguồn vào trong khe trên máy tính. 2 Luồn dây cáp cổng đầu nối nguồn xuyên qua các rãnh đi dây. 3 Đấu nối dây cáp cổng đầu nối nguồn vào đầu nối trên bo mạch hệ thống. 4 Vặn con vít để giữ chặt cổng đầu nối nguồn vào máy tính. 5 Lắp đặt: a b c d e f 6 cáp màn hình hiển thị chỗ dựa tay bàn phím cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính.
b c Tháo con vít đang giữ chặt bo mạch hệ thống vào máy tính [1]. Nhấc lên và tháo bo mạch hệ thống ra khỏi máy tính [2]. Lắp đặt bo mạch hệ thống 1 Đặt bo mạch hệ thống vào trong khe trên máy tính. 2 Đấu nối dây cáp cổng nguồn, dây cáp bo mạch VGA, dây cáp bo mạch I/O và dây cáp loa vào các đầu nối trên bo mạch hệ thống 3 Vặn vít để giữ chặt bo mạch hệ thống vào máy tính.
e f g h i 5 bộ nhớ card WLAN cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo tản nhiệt 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo: a b c d e f g h i j 3 pin nắp đế cụm ổ đĩa cứng card WLAN bộ nhớ bàn phím chỗ dựa tay cáp màn hình hiển thị quạt hệ thống bo mạch hệ thống Cách tháo tản nhiệt: a b Tháo các vít đang giữ chặt tản nhiệt vào bo mạch hệ thống [1, 2, 3, 4, 5, 6]. Nhấc lên và tháo tản nhiệt ra khỏi máy tính [7].
i j 4 nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính. Tháo cụm màn hình 1 Làm theo quy trình trong Trước khi thao tác bên trong máy tính. 2 Tháo: a b c d e f g h i j k 3 pin nắp đế cụm ổ đĩa cứng card WLAN bộ nhớ bàn phím chỗ dựa tay cáp màn hình hiển thị cổng đầu nối nguồn quạt hệ thống bo mạch hệ thống Cách tháo cụm màn hình: a Rút đấu nối và tháo dây cáp màn hình và dây cáp ăng ten WLAN ra khỏi hệ thống [1,2]. b c d Tháo đệm cao su ở cả hai bên của máy tính [1].
Lắp đặt cụm màn hình 1 Đặt cụm màn hình vào để căn chỉnh với các lỗ bắt vít trên khung máy. 2 Vặn các vít để giữ chặt cụm màn hình vào khung máy. 3 Đặt đệm cao su vào cả hai bên của máy tính. 4 Luồn và đấu nối các dây cáp màn hình và WLAN vào khung máy. 5 Lắp đặt: a b c d e f g h i j k 6 bo mạch hệ thống quạt hệ thống cáp màn hình hiển thị cổng đầu nối nguồn chỗ dựa tay bàn phím bộ nhớ card WLAN cụm ổ đĩa cứng nắp đế pin Làm theo quy trình trong Sau khi thao tác bên trong máy tính.
3 Cách tháo camera: a b Ngắt kết nối dây cáp camera khỏi đầu nối trên cụm màn hình [1]. Nhấc và tháo camera khỏi cụm màn hình [2]. Lắp đặt camera 1 Lắp camera vào trong khe cắm trên cụm màn hình. 2 Đấu nối dây cáp camera vào đầu nối trên cụm màn hình.
k cổng đầu nối nguồn l cụm màn hình m khung bezel màn hình 3 Cách tháo panel màn hình: a b c Tháo các vít đang gắn panel màn hình vào cụm màn hình hiển thị [1]. Tháo panel màn hình ra khỏi cụm màn hình [2]. Lột lớp băng dính [3] và ngắt đấu nối dây cáp LVDS ra khỏi đầu nối trên panel màn hình [4]. Lắp đặt panel màn hình 1 Đấu nối dây cáp LVDS vào đầu nối trên panel màn hình. 2 Dán lớp băng dính để giữ chặt dây cáp LVDS. 3 Đặt panel màn hình để căn chỉnh với các lỗ bắt vít trên cụm màn hình.
e f g h i j k l 3 bộ nhớ bàn phím chỗ dựa tay cáp màn hình hiển thị quạt hệ thống bo mạch hệ thống cổng đầu nối nguồn cụm màn hình Cách tháo khung bezel màn hình: THẬN TRỌNG: Có một lớp băng dính chặt trên khung bezel, hãy cẩn thận hơn khi tháo khung bezel màn hình lần đầu tiên. a b Sử dụng que nhựa mũi nhọn tháo khung bezel màn hình khỏi phần cuối của cụm màn hình [1]. Nhả khung bezel màn hình khỏi các mép cạnh và tháo khung bezel màn hình khỏi cụm màn hình [2, 3, 4].
3 Thiết lập hệ thống System Setup (Thiết lập Hệ thống) cho phép bạn quản lý các phần cứng máy tính của bạn và xác định các tùy chọn mức BIOS.
• Ổ đĩa quang • Chẩn đoán GHI CHÚ: Chọn Diagnostics (Chẩn đoán), sẽ hiển thị màn hình ePSA diagnostics. Màn hình trình tự khởi động cũng hiển thị tùy chọn truy cập màn hình System Setup (Thiết lập Hệ thống). Các phím điều hướng Bảng dưới đây hiển thị các phím điều hướng thiết lập hệ thống. GHI CHÚ: Đối với hầu hết các tùy chọn System Setup (Thiết lập Hệ thống), những thay đổi mà bạn thực hiện sẽ được ghi nhận nhưng chưa có hiệu lực tới khi bạn khởi động lại hệ thống. Bảng 1.
Các tùy chọn màn hình General (Tổng quan) Mục này liệt kê các tính năng phần cứng chính yếu của máy tính. Tùy chọn Mô tả System Information • System Information (Thông tin hệ thống): Hiển thị BIOS Version (Phiên bản BIOS), Service Tag (Thẻ dịch vụ), Asset Tag (Thẻ tài sản), Ownership Tag (Thẻ sở hữu), Ownership Date (Ngày sở hữu), Manufacture Date (Ngày sản xuất) và Express Service Code (Mã dịch vụ nhanh).
Tùy chọn Mô tả SATA Operation Cho phép bạn cấu hình bộ điều khiển ổ đĩa cứng SATA gắn trong. Các tùy chọn gồm: • Disabled (Tắt) • AHCI :Tùy chọn này được bật theo mặc định. Drives Cho phép bạn cấu hình các ổ đĩa cứng SATA trên bo mạch. Tất cả các ổ đĩa đều được bật theo mặc định. Các tùy chọn gồm: • SATA-0 SMART Reporting Trường này sẽ kiểm soát xem có báo cáo các lỗi ổ đĩa cứng đối với các ổ đĩa tích hợp hay không trong quá trình khởi động hệ thống.
Tùy chọn Mô tả GHI CHÚ: Tất cả các thiết bị được bật theo mặc định. Các tùy chọn màn hình video Tùy chọn Mô tả LCD Brightness Cho phép bạn cài độ sáng màn hình tùy thuộc vào nguồn điện (khi dùng Pin và khi dùng nguồn AC). Switchable Graphics Cho phép bạn bật hoặc tắt các công nghệ đồ họa chuyển đổi được, ví dụ như NVIDIA, Optimus và AMD PowerExpress/X99. GHI CHÚ: Cài đặt video sẽ chỉ được hiển thị khi lắp đặt card video vào hệ thống.
Tùy chọn Mô tả Cài đặt mặc định: Allow Non-Admin Password Changes (Cho phép thay đổi mật khẩu không phải của quản trị viên) được chọn. Non-Admin Setup Changes Cho phép bạn xác định xem có được phép thay đổi các tùy chọn thiết lập hay không khi đang cài Mật khẩu quản trị viên. Nếu bị tắt, các tùy chọn thiết lập sẽ bị khóa bằng mật khẩu quản trị. TPM Security Cho phép bạn kích hoạt Trusted Platform Module (TPM) trong quá trình khởi động POST.
Tùy chọn Mô tả • Enabled (Bật) Cài đặt mặc định: Enabled (Bật). Expert Key Management Chỉ cho phép bạn thao tác cơ sở dữ liệu khóa bảo mật khi hệ thống ở Chế độ tùy chỉnh. Tùy chọn Enable Custom Mode (Bật chế độ tùy chỉnh) được tắt theo mặc định. Các tùy chọn gồm: • PK • KEK • db • dbx Nếu bạn bật Custom Mode (Chế độ tùy chỉnh), các tùy chọn liên quan cho PK, KEK, db và dbx sẽ xuất hiện.
Tùy chọn Mô tả • Enabled (Bật) Cài đặt mặc định: Enabled (Bật). Các tùy chọn màn hình Power Management (Quản lý Nguồn điện) Tùy chọn Mô tả AC Behavior Cho phép bạn kích hoạt hoặc vô hiệu hóa tính năng tự động bật máy tính khi đấu nối bộ chuyển đổi nguồn AC. Cài đặt mặc định: Wake on AC (Đánh thức khi có nguồn AC) không được chọn. Auto On Time Cho phép bạn cài giờ mà máy tính phải tự động bật lên.
Tùy chọn Mô tả Cài đặt mặc định: Tùy chọn này được tắt Advanced Battery Tùy chọn này cho phép bạn tối đa hóa tuổi thọ pin. Bằng cách bật tùy chọn này, hệ thống sẽ sử dụng giải Charge thuật sạc pin tiêu chuẩn và các kỹ thuật khác, trong suốt thời gian không làm việc nhằm cải thiện tuổi thọ Configuration pin. Disabled (Tắt) Cài đặt mặc định: Disabled (Tắt) Primary Battery Charge Configuration Cho phép bạn chọn chế độ sạc cho pin.
Tùy chọn Mô tả Extended BIOS POST Time Cho phép bạn tạo thêm trì hoãn trước khi khởi động. Các tùy chọn gồm: • 0 seconds (0 giây). Tùy chọn này được bật theo mặc định. • 5 seconds (5 giây) • 10 seconds (10 giây) Các tùy chọn màn hình Virtualization support (Hỗ trợ ảo hóa) Tùy chọn Mô tả Virtualization Cho phép bạn bật hoặc tắt tính năng Intel Virtualization Technology (Công nghệ ảo hóa Intel). Enable Intel Virtualization Technology (Bật Công nghệ ảo hóa Intel) (mặc định).
Tùy chọn Mô tả BIOS Downgrade Mục này kiểm soát việc flash firmware hệ thống trở về các bản sửa đổi trước đó. Các tùy chọn màn hình System Log (Nhật ký Hệ thống) Tùy chọn Mô tả BIOS Events Cho phép bạn xem và xóa các sự kiện POST của Thiết lập hệ thống (BIOS). Cập nhật BIOS Khuyến cáo nên cập nhật BIOS (Thiết lập hệ thống) của bạn, khi lắp lại bo mạch hệ thống hoặc nếu có bản cập nhật.
THẬN TRỌNG: Bất cứ ai cũng có thể truy cập dữ liệu được lưu trữ trên máy tính của bạn nếu máy không khóa và không ai để ý đến. GHI CHÚ: Máy tính của bạn được gửi cùng hệ thống và tính năng mật khẩu cài đặt bị vô hiệu hóa. Gán mật khẩu hệ thống và mật khẩu cài đặt Bạn có thể đặt Mật khẩu Hệ thống và/hoặc Mật khẩu Cài đặt mới hoặc thay Mật khẩu Hệ thống và/hoặc Mật khẩu Cài đặt hiện có chỉ khi Trạng thái Mật khẩu là Mở khóa. Nếu Trạng thái Mật khẩu là Khóa, bạn không thể thay đổi Mật khẩu Hệ thống.
5 Nhấn Esc và một thông báo sẽ nhắc bạn lưu các thay đổi. 6 Nhấn Y để lưu các thay đổi và thoát khỏi Thiết lập Hệ thống. Máy tính khởi động lại.
4 Chẩn đoán Nếu bạn gặp sự cố với máy tính, hãy chạy chẩn đoán ePSA trước khi liên hệ với Dell để được hỗ trợ về kỹ thuật. Mục đích của việc chạy chẩn đoán là kiểm tra phần cứng của máy tính mà không cần có thêm thiết bị hoặc có nguy cơ mất dữ liệu. Nếu bạn không thể tự khắc phục sự cố, nhân viên dịch vụ và hỗ trợ có thể sử dụng kết quả chẩn đoán để giúp bạn khắc phục sự cố.
Đèn trạng thái thiết bị Bảng 2. Đèn trạng thái thiết bị Biểu tượng Mô tả Bật sáng khi bạn bật máy tính và nhấp nháy khi máy tính đang ở chế độ quản lý nguồn điện. Bật sáng đều hoặc nhấp nháy để chỉ báo tình trạng pin. Đèn trạng thái pin Nếu máy tính được kết nối với ổ cắm điện, đèn báo pin sẽ hoạt động như sau: Đèn màu hổ Bộ chuyển đổi nguồn AC không phải của Dell chưa được xác thực hoặc chưa được hỗ trợ đang được gắn phách và đèn màu vào máy tính xách tay của bạn.
5 Thông số kỹ thuật GHI CHÚ: Các đề xuất sản phẩm có thể thay đổi theo từng khu vực. Để biết thêm thông tin về cấu hình máy tính của bạn trong: • Windows 10, hãy nhấp hoặc nhấn Start > Settings > System > About. • Windows 8.1 và Windows 8, hãy nhấp hoặc nhấn Start • Windows 7, hãy nhấp Start > PC Settings > PC and devices > PC Info. , nhấp phải My Computer, và sau đó chọn Properties.
Tính năng Thông số kỹ thuật L3 cache Tối đa 4 MB Thông số kỹ thuật bộ nhớ Tính năng Thông số kỹ thuật Đầu nối bộ nhớ hai đầu nối DDR3L có thể tiếp cận bên trong Dung lượng bộ nhớ 4 GB và 8 GB Loại bộ nhớ 1600 MHz (cấu hình DDR3L kênh đôi) Bộ nhớ tối thiểu 4 GB Bộ nhớ tối đa 16 GB (8x2) GB Thông số kỹ thuật âm thanh Tính năng Thông số kỹ thuật Loại Âm thanh chất lượng cao 4 kênh Bộ điều khiển Realtek ALC3234 Chuyển đổi âm thanh stereo 24-bit (analog-to-digital và digital-to-analog) Gi
Tính năng Thông số kỹ thuật GHI CHÚ: Camera RBG + IR chỉ dành cho ứng dụng Windows Hello và các ứng dụng khác không thể sử dụng camera này. Thông số kỹ thuật giao tiếp Tính năng Thông số kỹ thuật Bộ điều hợp mạng 10/100/1000 Mbps Ethernet LAN trên bo mạch chủ (LOM) Không dây Wi-Fi 802.11 b/g/n và 802.
Tính năng Thông số kỹ thuật Góc hoạt động 0° (đóng) đến tối thiểu 135° Tốc độ làm mới 60 Hz Góc nhìn ngang tối thiểu 40°/40° Góc nhìn dọc tối thiểu 10°/30° Độ lớn điểm ảnh 0,265 mm x 0,265 mm Màn hình ngoài VGA Thông số kỹ thuật bàn phím Tính năng Thông số kỹ thuật Số phím Hoa Kỳ 101, Brazil 104, Anh Quốc 102 và Nhật Bản 105 Thông số kỹ thuật bàn di chuột Tính năng Thông số kỹ thuật Vùng hoạt động: Trục X 104,00 mm (4,09 inch) Trục Y 64,00 mm (2,52 inch) Thông số kỹ thuật pin Tính nă
Tính năng Thông số kỹ thuật • Tuổi thọ tối đa 6–cell — 11,1 VDC 300 chu kỳ xả/sạc điện Nhiệt độ: Hoạt động 0 °C đến 50 °C (32 °F đến 122 °F) Không hoạt động -20 °C đến 65 °C (-4 °F đến 149 °F) Pin dạng đồng xu pin lithium dạng đồng xu 3 V CR2032 Thông số kỹ thuật bộ chuyển đổi nguồn AC Tính năng Thông số kỹ thuật Loại 65 W và 90 W Điện áp đầu vào 100 V AC đến 240 V AC Dòng đầu vào (tối đa) 1,50 A/1,60 A/1,70 A/2,50 A Tần số đầu vào 50 Hz đến 60 Hz Dòng điện ra 3,34 A / 4,62 A Điện áp
Tính năng Thông số kỹ thuật Trọng lượng tối thiểu (có cảm ứng) 2,06 kg (4,54 pound) Thông số kỹ thuật môi trường Nhiệt độ Thông số kỹ thuật Hoạt động 0°C đến 35°C (32°F đến 95°F) Bảo quản –40°C đến 65°C (–40°F đến 149°F) Độ ẩm tương đối (tối đa) Thông số kỹ thuật Hoạt động 10% đến 90% (không ngưng tụ) Bảo quản 10% đến 95% (không ngưng tụ) Độ cao (tối đa) Thông số kỹ thuật Hoạt động –15,2 m đến 3.048 m (–50 foot đến 10.000 foot) Không hoạt động –15,2 m đến 10.668 m (–50 foot đến 35.
6 Liên hệ Dell GHI CHÚ: Nếu bạn không có kết nối internet đang hoạt động, bạn có thể tìm thấy thông tin liên hệ trên hóa đơn mua hàng, phiếu gói hàng, hóa đơn, hoặc danh mục sản phẩm của Dell. Dell cung cấp một số tùy chọn dịch vụ và hỗ trợ trực tuyến và qua điện thoại. Dịch vụ có sẵn khác nhau tùy theo quốc gia và sản phẩm, và một số dịch vụ có thể không có sẵn trong khu vực của bạn. Để liên hệ với Dell để bán hàng, hỗ trợ kỹ thuật, hoặc các vấn đề dịch vụ khách hàng: 1 Truy cập vào Dell.com/support.