Latitude 3590 Benutzerhandbuch Vorschriftenmodell: P75F Vorschriftentyp: P75F001
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis 1 Arbeiten am Computer................................................................................................................................... 7 Sicherheitsvorkehrungen...................................................................................................................................................7 Standby-Stromversorgung..........................................................................................................................................
Einbauen der SSD-Karte........................................................................................................................................... 27 Lautsprecher.....................................................................................................................................................................27 Entfernen der Lautsprecher......................................................................................................................................
Entfernen der Systemplatine....................................................................................................................................50 Einbauen der Systemplatine..................................................................................................................................... 55 Handballenstütze.............................................................................................................................................................
Bildschirm Optionen......................................................................................................................................................... 81 Optionen des Bildschirms „Security“ (Sicherheit)....................................................................................................... 82 Optionen des Bildschirms „Secure Boot“ (Sicherer Start).........................................................................................
1 Arbeiten am Computer Themen: • Sicherheitsvorkehrungen • Vor der Arbeit an Komponenten im Innern des Computers • Nach der Arbeit an Komponenten im Inneren des Computers Sicherheitsvorkehrungen Im Kapitel zu den Vorsichtsmaßnahmen werden die primären Schritte, die vor der Demontage durchzuführen sind, detailliert beschrieben.
bereits auf eine Weise schädigen, die eventuell nicht offensichtlich ist (z. B. zeitweilige Probleme oder eine verkürzte Produktlebensdauer). Da die Branche auf geringeren Leistungsbedarf und höhere Dichte drängt, ist der ESD-Schutz von zunehmender Bedeutung. Aufgrund der höheren Dichte von Halbleitern, die in aktuellen Produkten von Dell verwendet werden, ist die Empfindlichkeit gegenüber Beschädigungen durch elektrostatische Entladungen inzwischen größer als bei früheren Dell-Produkten.
• Isolatorelemente: Es ist sehr wichtig, ESD-empfindliche Geräte, wie z. B. Kunststoff-Kühlkörpergehäuse, von internen Teilen fernzuhalten, die Isolatoren und oft stark geladen sind. • Arbeitsumgebung: Vor der Bereitstellung des ESD-Service-Kits sollten Sie die Situation am Standort des Kunden überprüfen. Zum Beispiel unterscheidet sich die Bereitstellung des Kits für eine Serverumgebung von der Bereitstellung für eine Desktop-PC- oder mobile Umgebung.
Vor der Arbeit an Komponenten im Innern des Computers 1 Stellen Sie sicher, dass die Arbeitsoberfläche eben und sauber ist, damit die Computerabdeckung nicht zerkratzt wird. 2 Schalten Sie den Computer aus. 3 Falls der Computer mit einem Docking-Gerät verbunden ist, trennen Sie die Verbindung. 4 Trennen Sie alle Netzwerkkabel vom Computer (falls verfügbar). VORSICHT: Wenn der Computer einen RJ45-Anschluss hat, trennen Sie das Netzwerkkabel, indem Sie zuerst das Kabel vom Computer abziehen.
2 Ausbau und Wiedereinbau Empfohlene Werkzeuge Für die in diesem Dokument beschriebenen Verfahren sind folgende Werkzeuge erforderlich: • Kreuzschlitzschraubendreher Nr. 0 • Kreuzschlitzschraubenzieher Nr. 1 • Kunststoffstift ANMERKUNG: Der Schraubenzieher Nr. 0 ist für Schrauben 0-1 und der Schraubenzieher Nr. 1 für Schrauben 2-4 Liste der Schraubengrößen Tabelle 1. Liste der Schraubengrößen Komponente M2 x 2 M2x2OD 5(Ni) Mx3 M2x4 M2.5x2.
Betriebsschalter zu Handballenstütze 1 Netzteilplatine an Handballenstütze 1 VGA-Platine an Handballenstütze 2 WWAN-Platine an Handballenstütze 2 E/A-Platine an Handballenstütze 1 Scharnierhalterung (L + R) an Handballenstütze 6 HDD-Halterung an Handballenstütze 4 Lüfter an Handballenstütze 3 Akku zu Handballenstütze 5 WLAN-Modul an Systemplatine 1 WWAN-Modul an WWANPlatine 1 SSD an Handballenstütze Fingerabdruckhalterung an Handballenstütze 1 1 Basis an Scharnierplatte (L + R) an Ha
3 Setzen Sie die Spitze einer Büroklammer in das Loch des SIM-Kartenfachsteckplatzes ein und ziehen Sie dann das SIM-Kartenfach mithilfe der Büroklammer heraus, um es zu entfernen. Installieren des SIM-Kartenfachs – WWAN-Modelle 1 Richten Sie das SIM-Kartenfach aus und führen Sie es wieder in den SIM-Kartenfachsteckplatz ein. 2 Schließen Sie die Abdeckung des SIM-Kartensteckplatzes. 3 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Installieren der SD-Karte – WWAN-Modelle 1 Drücken Sie die SD-Karte in den Steckplatz, bis die SD-Karte mit einem klickenden Geräusch einrastet. 2 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Abdeckung an der Unterseite Entfernen der Bodenabdeckung 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers 2 Entfernen Sie das SIM-Kartenfach (WWAN-Modelle).
b Hebeln Sie die Bodenabdeckung von der oberen rechten Kante [1] und fahren Sie im Uhrzeigersinn mit den äußeren Kanten der Bodenabdeckung fort [2]. ANMERKUNG: Sie benötigen eventuell einen Kunststoffstift, um die Bodenabdeckung von der Kanten abzuhebeln [1]. 4 Heben Sie die Bodenabdeckung vom Computer ab.
Einbauen der Bodenabdeckung 1 Richten Sie die Bodenabdeckung auf die Schraubenhalterungen am Computer aus. 2 Drücken Sie die Ränder der Tastatur, bis sie hörbar einrastet. 3 Ziehen Sie die zehn Schrauben (M2,5) fest, um die Abdeckung am Computer zu befestigen. 4 Installieren Sie das SIM-Kartenfach (WWAN-Modelle). 5 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Entfernen des Akkus 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Entfernen Sie folgende Komponenten: 3 So entfernen Sie den Akku: a Bodenabdeckung a Ziehen Sie das Akkukabel vom Anschluss an der Systemplatine ab . b Entfernen Sie die fünfM2,0x3,0-Schrauben, mit denen der Akku am Computer befestigt ist [1]. c ANMERKUNG: Bei Systemen mit 3-Zellen-Akku müssen Sie nur 3 Schrauben entfernen. Heben Sie den Akku aus dem Computer [2].
Einsetzen des Akkus 1 Setzen Sie den Akku in den Steckplatz im Computer ein. 2 Bringen Sie die fünf Schrauben (M2x3), mit denen der Akku am Computer befestigt wird, wieder an. 3 Schließen Sie das Akkukabel am Anschluss an der Systemplatine an. 4 Bauen Sie folgende Komponenten ein: ANMERKUNG: Der 3-Zellen-Akku hat nur 3 Schrauben. a b 5 Bodenabdeckung SIM-Kartenfach (WWAN-Modelle) Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Einbauen der WLAN-Karte 1 Setzen Sie die WLAN-Karte in den entsprechenden Anschluss auf der Systemplatine. 2 Verstauen Sie die Antennenkabel unterhalb des linken Bildschirmscharniers und verbinden Sie die Antennenkabel mit der WLAN-Karte. 3 Setzen Sie den WLAN-Kartenalter wieder auf die WLAN-Karte. 4 Ziehen Sie die Schraube (M2x3), mit der die WLAN-Karte an der Systemplatine befestigt wird, fest.
c Ziehen Sie die WWAN-Karte aus ihrem Steckplatz auf der Systemplatine [4]. Einbauen der WWAN-Karte 1 Setzen Sie die WWAN-Karte in den entsprechenden Anschluss auf der Systemplatine. 2 Schließen Sie die zwei Antennenkabel an der WWAN-Karte an. 3 Bringen Sie die Metallhalterung an der WWAN-Karte an. 4 Ziehen Sie die M2xL3-Schraube fest, um die WWAN-Karte und die Halterung an der Systemplatine zu befestigen.
Installieren der VGA-Platine 1 Setzen Sie die VGA-Platine im entsprechenden Steckplatz auf der Systemplatine ein. 2 Bringen Sie die beiden Schrauben (M2x3), mit denen die VGA-Platine am System befestigt wird, wieder an. 3 Verbinden Sie das VGA-Tochterplatinenkabel mit der VGA-Tochterplatine. 4 Bauen Sie folgende Komponenten ein: a b 5 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Speichermodul Entfernen des Speichermoduls 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Entfernen Sie folgende Komponenten: a b 3 Bodenabdeckung Akku So entfernen Sie das Speicher-Modul: a b Hebeln Sie die Riegel des Speichermoduls ab [1]. Heben Sie das Speichermodul an und entfernen Sie es von der Systemplatine [2].
Festplattenlaufwerk Entfernen des Festplattenlaufwerks 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Entfernen Sie folgende Komponenten: a b 3 Bodenabdeckung Akku So entfernen Sie das Festplattenlaufwerk (HDD): a Trennen Sie das HDD-Kabel von der Systemplatine . b c Entfernen Sie die vier M3x3-Schrauben, mit denen das HDD an der Handballenstütze befestigt ist [1]. Heben Sie das HDD aus dem Computer [2].
4 Trennen Sie den HDD-Kabel-Interposer. 5 Lösen Sie die M3xL3-Schrauben, um die Halterung vom HDD zu trennen.
6 Heben Sie die Halterung vom Festplattenlaufwerk. Installieren des Festplattenlaufwerks 1 Ziehen Sie die Schrauben (M3x3) fest, um die Halterung am Festplattenlaufwerk zu befestigen. 2 Verbinden Sie den Kabel-Interposer des Festplattenlaufwerks. 3 Setzen Sie das Festplattenlaufwerk in den entsprechenden Stecker im Computer ein. 4 Ziehen Sie die vier Schrauben (M3x3) fest, um das Festplattenlaufwerk am Computer zu befestigen.
6 Bauen Sie folgende Komponenten ein: a b 7 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. SATA-Solid-State-Festplatte (SSD) Entfernen der SSD-Karte 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers.
Einbauen der SSD-Karte 1 Setzen Sie die SSD-Karte in den entsprechenden Steckplatz im System ein. 2 Platzieren Sie die SSD-Halterung im entsprechenden Steckplatz am Computer und ziehen Sie die Schrauben fest, um sie am System zu befestigen. 3 Installieren Sie Folgendes: . a b 4 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Einbauen der Lautsprecher 1 Richten Sie die Lautsprecher an den Steckplätzen am Computer aus. 2 Bringen Sie das Klebeband, mit dem das Lautsprecherkabel am Computer befestigt wird, an. 3 Führen Sie das Lautsprecherkabel durch den dafür vorgesehenen Kabelführungskanal. 4 Schließen Sie das Lautsprecherkabel wieder an den Anschluss an der Systemplatine an.
Installieren der Knopfzellenbatterie 1 Setzen Sie die Knopfzellenbatterie in den Steckplatz auf der Systemplatine ein. 2 Verbinden Sie das Batteriekabel mit der Systemplatine. 3 Bauen Sie folgende Komponenten ein: a b 4 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Kühlkörper Entfernen des Kühlkörpers 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers.
b 30 Heben Sie den Kühlkörper aus dem Computer heraus.
Einbauen des Kühlkörpers 1 Setzen Sie den Kühlkörper in den entsprechenden Steckplatz im Computer ein. 2 Ziehen Sie die M2,5x2,5-Schrauben fest und bringen Sie die drei M2x3-Schrauben wieder an, um den Kühlkörper am Computer zu befestigen. ANMERKUNG: Ziehen Sie die Schrauben des Kühlkörpers in der auf dem Kühlkörper angegebene Reihenfolge fest. 3 Bauen Sie folgende Komponenten ein: a Akku b Bodenabdeckung 4 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Einbauen des Systemlüfters 1 Setzen Sie den Lüfter auf den Computer. 2 Ziehen Sie die drei Schrauben (M2,5x5), mit denen der Lüfter am Computer befestigt wird, fest. 3 Schließen Sie das Lüfterkabel an die Systemplatine an. 4 Führen Sie das eDP-Kabel durch die Kabelführung am Systemlüfter. 5 Bauen Sie folgende Komponenten ein: a b 6 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
4 Entfernen Sie die M2x4-Schraube, mit der die E/A-Platine [1] am System befestigt ist, und heben Sie sie aus dem System [2].
Installieren der Eingabe/Ausgabe-Platine 1 Platzieren Sie die Eingabe/Ausgabe-Platine (E/A-Platine) im entsprechenden Steckplatz auf der Handballenstütze. 2 Bringen Sie die Schraube (M2x4), mit denen die E/A-Platine an der Handballenstütze befestigt wird, wieder an. 3 Verbinden Sie das E/A-Platinenkabel mit dem dafür vorgesehenen Anschluss auf der Systemplatine.
c Heben Sie den Fingerabdruckleser aus dem Computer.
Einbauen des Fingerabdrucklesers 1 Setzen Sie die den Fingerabdruckleser in den entsprechenden Steckplatz auf der Handballenstütze ein. 2 Platzieren Sie die Metallhalterung auf dem Fingerabdruckleser und bringen Sie die Schraube wieder an, um den Fingerabdruckleser am System zu befestigen. 3 Befestigen Sie das selbstklebende Kabel sicher an der Handballenstütze. 4 Verbinden Sie den Fingerabdruckleser mit dem Anschluss auf der Systemplatine.
7 Entfernen Sie die vier Schrauben (M2x2), mit denen das Touchpad auf dem Computer befestigt ist [1] und heben Sie das Touchpad aus dem System [2].
Installieren des Touchpads 1 Setzen Sie das Touchpad in den Steckplatz im Computer ein und bringen Sie die vier M2x2-Schrauben an, mit denen es am System befestigt wird. 2 Schließen Sie die Kabel des Touchpads und der Tastaturhintergrundbeleuchtung an ihre jeweiligen Anschlüsse auf der Systemplatine an. 3 Bringen Sie das Klebeband an, um das Touchpad am System zu befestigen. 4 Richten Sie die Metallhalterung an der Kunststofffixierung aus und setzen Sie sie darunter ein.
7 Öffnen Sie die Handballenstützen-Baugruppe dann in einem Winkel von mindestens 90 Grad und stellen Sie das System auf die Kante eines Tischs, sodass die Handauflage flach auf dem Tisch liegt und die Bildschirmbaugruppe über den Rand ragt. VORSICHT: Halten Sie das System fest, während Sie es in dieser Position platzieren.
8 Entfernen Sie die sechs M2,5x2,5-Schrauben [1] und heben Sie die Bildschirmbaugruppe aus dem Computer [2]. VORSICHT: Halten Sie die Bildschirmbaugruppe fest, während Sie sie in einem Winkel von 90 Grad auf der Handballenstütze platzieren, um Beschädigungen an der Bildschirmbaugruppe zu vermeiden. Einbauen der Bildschirmbaugruppe 1 Platzieren Sie die Bildschirmbaugruppe in einem Winkel von 90 Grad auf der Handballenstütze und richten Sie sie an den Schraubenhalterungen an der Handballenstütze aus.
c d 10 Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. DC-In Anschluss Entfernen des DC-In-Anschlusses 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers.
3 Führen Sie das DC-In-Kabel durch die Klammern am System. 4 Schließen Sie das DC-In-Kabel an den Anschluss auf der Systemplatine an. 5 Bauen Sie folgende Komponenten ein: a Bildschirmbaugruppe b WLAN c WWAN d Akku e Bodenabdeckung 6 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Betriebsschalterplatine Entfernen der Betriebsschalterplatine 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers.
Installieren der Betriebsschalterplatine 1 Setzen Sie die Betriebsschalterplatine in den entsprechenden Steckplatz. 2 Ziehen Sie die Schraube (M2x2), mit der die Betriebsschalterplatine am System befestigt wird, wieder fest. 3 Bringen Sie das Klebeband, mit dem die Betriebsschalterplatine am System befestigt wird, wieder an. 4 Befestigen Sie das selbstklebende Kabel der Betriebsschalterplatine am System und verbinden Sie dann das Kabel mit dem entsprechenden Stecker auf der Systemplatine.
Installieren der LCD-Blende 1 Setzen Sie die Blende wieder ein und drücken Sie vorsichtig auf die Ränder, bis die Blende einrastet. 2 Bauen Sie folgende Komponenten ein: a b c d e 3 Bildschirmbaugruppe Einbauen der WWAN-Karte Einbauen der WLAN-Karte Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Kamera Entfernen der Kamera 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers.
Einbauen der Kamera 1 Platzieren Sie die Kamera auf der rückseitigen LCD-Abdeckung. 2 Verbinden Sie das Kamerakabel mit dem entsprechenden Anschluss. 3 Bringen Sie das Klebeband an, um die Kamera an der LCD-Abdeckung zu befestigen. 4 Bauen Sie folgende Komponenten ein: a b c d e f 5 LCD-Blende Bildschirmbaugruppe WWAN WLAN Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
a b c d e Bodenabdeckung WLAN-Karte WWAN-Karte Bildschirmbaugruppe LCD-Blende 3 Ziehen Sie das Klebeband ab, mit dem der LCD-Bildschirm an der hinteren LCD-Abdeckung befestigt ist [1]. 4 Entfernen Sie die vier M2x2-Schrauben, mit denen der LCD-Bildschirm an der hinteren LCD-Abdeckung befestigt ist [2], und drehen Sie den Bildschirm um, damit der eDP-Kabelanschluss sichtbar ist [3].
Installieren des LCD-Bildschirms 1 Verbinden Sie das LCD-Kabel mit dem entsprechenden Stecker auf der Rückseite des LCD-Bildschirms. 2 Bringen Sie den Aufkleber an. 3 Setzen Sie den LCD-Bildschirm auf die hintere LCD-Bildschirmabdeckung und richten Sie den LCD-Bildschirm auf die Schraubenhalterungen an der hinteren LCD-Bildschirmabdeckung aus. 4 Bringen Sie die vier Schrauben (M2x2), mit denen der LCD-Bildschirm an der hinteren LCD-Bildschirmabdeckung befestigt ist, wieder an.
c d e f WWAN-Karte Bildschirmbaugruppe LCD-Blende LCD-Bildschirm 3 Entfernen Sie die acht M2,5x2,5M2x2-Schrauben, mit denen die Metallhalterungen an der hinteren LCD-Abdeckung befestigt sind [1]. 4 Entfernen Sie das LCD-Scharnier aus dem System [2]. Installieren des LCD-Scharniers 1 Positionieren Sie die linke und die rechte Scharnierhalterung auf der hinteren LCD-Abdeckung und richten Sie sie auf die Sperrlaschen an der Seite der hinteren LCD-Abdeckung aus.
eDP- und Kamerakabel Entfernen des eDP-Kabels und des Kamerakabels 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Entfernen Sie folgende Komponenten: a b c d e f Bodenabdeckung WLAN-Karte WWAN-Karte Bildschirmbaugruppe LCD-Blende LCD-Bildschirm 3 Entfernen Sie das Klebeband, mit dem das Kamera- und eDP-Kabel befestigt sind [1].
Installieren des eDP-Kabels und des Kamerakabels 1 Führen Sie das Bildschirmkabel durch die Kabelführung und befestigen Sie das Bildschirmkabel mithilfe der Klebestreifen an der rückseitigen LCD-Abdeckung. 2 Verbinden Sie das Kamerakabel mit dem entsprechenden Stecker auf der rückseitigen LCD-Abdeckung. 3 Bringen Sie die Schrauben, mit denen die rechte Scharnierhalterung an der LCD-Abdeckung befestigt wird, wieder an.
d e 3 Trennen Sie die folgenden Kabel und Anschlüsse: a b c d e 4 WWAN-Karte Bildschirmbaugruppe VGA-Kabel [1] Entfernen Sie das VGA-Kabel aus der Kabelführung [2].
5 Entfernen Sie die Schraube (M2x4), mit der die Systemplatine am System befestigt ist.
• Für Systeme mit WWAN-Karte und Fingerabdrucksensor: 1 Heben Sie vorsichtig die rechte Seite der Systemplatine an und drehen Sie sie um. 2 Trennen Sie das WWAN-Tochterplatine-FPC [1] und das VGA-Kabel der Tochterplatine [2] von den Steckern auf der 3 Heben Sie die Systemplatine aus dem System. Unterseite der Systemplatine.
• 7 Heben Sie bei anderen Konfigurationen die Systemplatine heraus. Entfernen Sie die Schraube, mit der die USB-Typ-C-Halterung an der Systemplatine befestigt ist [1] und heben Sie die USB-Typ-CHalterung von der Systemplatine ab [2].
Einbauen der Systemplatine 1 Verbinden Sie die Kabel für WWAN und Fingerabdruckleser mit den Steckern auf der Unterseite der Systemplatine. ANMERKUNG: Dieser Schritt gilt nur für Systeme mit WWAN-Karte und Fingerabdruckleser. 2 Richten Sie die Systemplatine an den Schraubenhalterungen am Computer aus. 3 Ziehen Sie die Schraube (M2x4) fest, um die Systemplatine am Computer zu befestigen.
Handballenstütze Entfernen der Handballenstütze 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Entfernen Sie folgende Komponenten: a b c d e f g h i j k l m n o Bodenabdeckung Akku Kühlkörper Lüfter WLAN-Karte WWAN-Karte Speichermodul HDD (Festplatte) DC-In-Port E/A-Platine Knopfzellenbatterie Lautsprecher Touchpad Bildschirmbaugruppe Systemplatine ANMERKUNG: Die letzte Komponente ist die Handballenstütze.
e f g h i j k l m n o 4 Knopfzellenbatterie E/A-Platine DC-In-Port Speichermodul WWAN-Karte WLAN-Karte HDD (Festplatte) Lüfter Kühlkörper Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
3 Technische Daten ANMERKUNG: Die angebotenen Konfigurationen können je nach Region variieren. Weitere Informationen zur Konfiguration Ihres Computers: • Windows 10: Klicken oder tippen Sie auf Start > Settings > System > About.
Speicher Ihr Computer unterstützt maximal 32 GB Speicher, sofern Sie zwei DIMM-Module von je 16 GB verwenden. Allerdings können 32-BitBetriebssysteme, wie zum Beispiel die 32-Bit-Version von Microsoft Windows 10 lediglich einen maximalen Adressraum von 4 GB verwenden. Außerdem erfordern bestimmte Komponenten im Computer Adressraum im Bereich von 4 GB. Adressen, die für diese Komponenten reserviert sind, können vom Computerspeicher nicht genutzt werden.
Video Tabelle 3. Die Tabelle gibt die Videospezifikationen an Funktion Technische Daten Typ Auf Systemplatine integriert, hardwarebeschleunigt Controller UMA : • • Sky Lake: Intel HD-Grafikkarte 520 Kaby Lake: Intel HD Gafikkarte 610\620, Intel UHD-Grafikkarte 620 Separat: • Unterstützung für externe Anzeigen AMD Radeon 530 VGA, HDMI 1.4 Webcam – Technische Daten Dieser Abschnitt enthält detaillierte technische Daten der Kamera.
Datenraten 10/100/1000 MBit/s Controller-Bus-Architektur PCIe V1.1x1 Leistungsaufnahme (vollständiger Betrieb pro Datenverbindungsgeschwindigkeit) 1 000 Mbit/s: 828 mW 100 Mbit/s: 441,77 mW 10 Mbit/s: 387,94 mW Stromverbrauch (Standby-Betrieb) WOL deaktiviert: 10 mW (über Treiber deaktiviert) Keine Verbindung (mit WOL): 51,89 mW (Kabel getrennt) 10 Mbit/s im Leerlauf (mit WOL): 68 mW 100 Mbit/s im Leerlauf (mit WOL): 176 mW Konformität mit IEEE-Standards 802.3, 802.3ab, 802.3u, 802.
Attribut Technische Daten 802.11g/a: –72 dBm bei 54 Mbit/s 802.
Attribut Technische Daten Dual-Diversity-Antennenumschaltung Dual-Diversity-Antennenumschaltung für Systeme mit Haupt- und Zusatzantennen. 2x2-MIMO-Vorgang bei 802.11n-Modus mit 2x2 oder höherem Zugangspunkt. Datenübertragungsrate 802.11ac – bis zu 867 Mbit/s, 802.11n – bis zu 450 Mbit/s, 802.11a/g – bis zu 54 Mbit/s 802.11b – bis zu 11 Mbit/s Empfangsempfindlichkeit 802.11ac: –59 dBm bei 400 Mbit/s, –57dBm bei 866,7 Mbit/s 802.11n/a: –67 dBm bei 300 Mbit/s, –70 dBm bei 144,4 Mbit/s 802.
Tabelle 8. Intel® Dual Band Wireless-AC 8265 802.11AC 2x2 Wi-Fi + BT 4.2 LE-M.2-Wireless-Karte Attribut Technische Daten Hostschnittstelle M.2 2230-Formfaktor (WiFi – PCIe, Bluetooth – USB) Netzwerkstandard IEEE 802.11a/b/g/n/ac MU-MIMO RX Wi-Fi-Alliance-Zertifizierung 802.
Attribut Technische Daten Temperatur Betriebstemperatur: 0 °C bis +50 °C (volle Leistung bei abgeschirmten Temperaturen bis zu 80 °C) Lagertemperatur: –40 °C bis +70 °C Luftfeuchtigkeit Bis zu 90 % relative Luftfeuchtigkeit, nicht kondensierend (bei Temperaturen zwischen 25 °C und 35 °C) Tabelle 9.
Träger Allgemein China / Indonesien Auffangnetzwerk HSPA+ HSPA+ Auffanggeschwindigkeit HSPA+ 42 Mbit/s HSPA+ 42 Mbit/s Frequenzbänder Band 1, 2, 3, 4, 5, 8, HSPA+ Band 1, 2, 3, 4, 5, 8, HSPA+ SIM-Karte Ja Ja LTE/WWAN-Antenne Hauptantenne (Tx/Rx) + Zusatzantenne (Rx/GNSS) Hauptantenne (Tx/Rx) + Zusatzantenne (Rx/GNSS) Betriebssystemunterstützung Windows 8.1 (32/64 Bit) Windows 8.
Tabelle 12.
Fn + F8 Anzeige umschalten (Win + P) Fn + F9 Suchen Fn + F10 Helligkeit der Tastaturbeleuchtung erhöhen Fn + F11 Helligkeit erhöhen Fn + F12 Helligkeit verringern Fn + Drucktaste Wireless • Primäres Verhalten bedeutet Tasten F1–F12, sekundäres Verhalten bedeutet Medientasten. • Fn-Sperre ändert nur zwischen primärem und sekundärem Verhalten der Tasten F1–F12 • F7 verhält sich identisch, es gibt kein sekundäres Verhalten Touchpad Tabelle 14.
Akku Dieser Abschnitt enthält detaillierte technische Daten des Akkus. Tabelle 16.
Ausgangsstrom 3,34A (Dauerstrom) 3,34A (Dauerstrom) Ausgangsnennspannung 19,5 V Gleichspannung 19,5 V Gleichspannung Gewicht (kg): 0,23 0,29 Abmessungen (HxBxT in Zoll) 1,1 x 1,9 x 4,3 1,1 x 1,9 x 4,3 Abmessungen (HxBxT in mml) 28 x 47 x 108 28 x 47 x 108 Temperaturbereich: 0 °C bis 40 °C 0 °C bis 40 °C Betrieb 32 °F bis 104 °F 32 °F bis 104 °F Bei Lagerung –40 °C bis 70 °C –40 °C bis 70 °C –40 °F bis 158 °F –40 °F bis 158 °F Abmessungen des Systems Dieses Thema enthält eine detail
4 Technologie und Komponenten Dieses Kapitel erläutert die in dem System verfügbare Technologie und Komponenten. Themen: • DDR4 • USB-Funktionen • HDMI 1.4 • USB Typ-C DDR4 DDR4-Speicher (Double Data Rate der vierten Generation) ist der schnellere Nachfolger der DDR2- und DDR3-Technologie und ermöglicht bis zu 512 GB Kapazität im Vergleich zu der maximalen Kapazität von 128 GB pro DIMM bei DDR3-Speicher.
Abbildung 2. Stärkenunterschied Gebogene Kante DDR4-Module haben eine gebogene Kante zur Unterstützung beim Einsetzen und zur Verringerung der Beanspruchung der PCB während der Arbeitsspeicherinstallation. Abbildung 3. Gebogene Kante Speicherfehler Bei Speicherfehlern im System wird der neue Fehlercode EIN-BLINKEN-BLINKEN oder EIN-BLINKEN-EIN angezeigt. Wenn der gesamte Speicher ausfällt, schaltet sich die LCD-Anzeige nicht ein.
Nachfrage nach größerer Bandbreiten gestiegen. Der USB 3.0/USB 3.1 Gen 1 hat endlich die Antwort auf die Anforderungen der Verbraucher. Er ist theoretisch 10 mal schneller als sein Vorgänger. Eine Übersicht der USB 3.
Anwendungen USB 3.0 /USB-3.1 Gen 1 öffnet Wege und bietet Geräten mehr Raum für bessere Gesamtfunktionalität. USB-Video war zuvor was maximale Auflösung, Latenz und Videokomprimierung anbelangt nicht akzeptabel. Aufgrund der 5 bis 10 mal größeren Bandbreite lassen sich nun weitaus bessere USB-Videolösungen vorstellen. Single-link-DVI erfordert einen Durchsatz von nahezu 2 Gbit/s. 480 Mbit/s legte Beschränkungen auf, 5 Gbit/s ist mehr als vielversprechend.
Funktionen von HDMI 1.
Geräte verwenden. Sie können Ihren Laptop an ein externes Display anschließen, das an ein Stromkabel angeschlossen ist, und dieses externe Display lädt Ihren Laptop auf, während Sie ihn als externes Display verwenden – alles über den kleinen USB-Typ-C-Anschluss. Dazu müssen das Gerät und das Kabel USB Power Delivery unterstützen. Allein ein USB-Typ-C-Anschluss bedeutet nicht unbedingt, dass sie das tun. USB Typ C und USB 3.1 USB 3.1 ist ein neuer USB-Standard. Die theoretische Bandbreite von USB 3.
5 Optionen des System-Setup ANMERKUNG: Abhängig von Ihrem Computer und den installierten Geräten werden manche der in diesem Abschnitt beschriebenen Elemente möglicherweise nicht angezeigt.
• Diagnose ANMERKUNG: Bei Auswahl von Diagnostics (Diagnose) wird der ePSA diagnostics (ePSA-Diagnose)-Bildschirm angezeigt. Der Startreihenfolgebildschirm zeigt auch die Optionen zum Zugriff auf den System-Setup-Bildschirm an. Navigationstasten ANMERKUNG: Bei den meisten Optionen im System-Setup werden Änderungen zunächst nur gespeichert und erst beim Neustart des Systems wirksam. Tasten Navigation Pfeil nach oben Zurück zum vorherigen Feld. Pfeil nach unten Weiter zum nächsten Feld.
Option Beschreibung System Information In diesem Abschnitt werden die primären Hardwarefunktionen des Computers aufgelistet. • System Information (Systeminformationen): Angezeigt werden BIOS Version, Service Tag, Asset Tag, Ownership Date, Manufacture Date und der Express Service Code (BIOS-Version, Service-Tag-Nummer, Systemkennnummer, Besitzkennnummer, Besitzdatum, Herstellungsdatum und der Express-Servicecode).
Option Beschreibung SATA Operation Ermöglicht die Konfiguration des Betriebsmodus des integrierten SATA-Festplatten-Controllers. Drives • Deaktiviert • AHCI • RAID On (RAID Ein) – Standardeinstellung Bietet Ihnen die Möglichkeit, verschiedene Laufwerke zu aktivieren bzw. zu deaktivieren: • SATA-0 (Standardeinstellung) • SATA-2 (Standardeinstellung) • M.
Option Beschreibung Keyboard Backlight Timeout on AC Die Optionen sind: Keyboard Backlight Timeout on Battery • 5 seconds (5 Sekunden) • 10 seconds (10 Sekunden) (Standardeinstellung) • 15 seconds (15 Sekunden) • 30 seconds (30 Sekunden) • 1 minute (1 Minute) • 5 minutes (5 Minuten) • 15 minutes (15 Minuten) • Never (Nie) Diese Funktion legt den Timeout-Wert für die Tastaturbeleuchtung fest, wenn das System nur mit Akkustrom versorgt wird.
Optionen des Bildschirms „Security“ (Sicherheit) Option Beschreibung Admin Password Ermöglicht das Einrichten, Ändern oder Löschen des Administratorkennworts (Admin). ANMERKUNG: Vor dem Einrichten des System- und Festplattenkennworts müssen Sie das Administratorkennwort festlegen. Durch Löschen des Administratorkennworts werden auch das Systemkennwort und das Festplattenkennwort automatisch gelöscht. ANMERKUNG: Erfolgreiche Kennwortänderungen werden sofort wirksam.
Option Beschreibung UEFI Capsule Firmware Updates Ermöglicht Ihnen das Aktivieren und Deaktivieren. Diese Option steuert, ob das System BIOS-Aktualisierungen über UEFI Capsule-Aktualisierungspakete zulässt. Die Optionen sind: • TPM 2.0 Security Enable UEFI Capsule Firmware (UEFI Capsule Firmware aktivieren) – standardmäßig aktiviert Ermöglicht das Aktivieren des TPM (Trusted Platform Module, vertrauenswürdiges Plattformmodul) während des POST.
Optionen des Bildschirms „Secure Boot“ (Sicherer Start) Option Beschreibung Secure Boot Enable Diese Option aktiviert oder deaktiviert die Funktion Secure Boot (Sicherer Start). Expert Key Management (Erweiterte Schlüsselverwalltun g) • Deaktiviert • Enabled (Aktiviert) (Standardeinstellung) Die Sicherheitsschlüssel-Datenbanken können nur bearbeitet werden, wenn sich das System im benutzerdefinierten Modus befindet.
Optionen des Bildschirms „Performance“ (Leistung) Option Beschreibung Multi Core Support In diesem Feld wird angegeben, ob einer oder alle Cores des Prozesses aktiviert sind. Die Leistung mancher Anwendungen verbessert sich mit zusätzlichen Cores. Diese Option ist standardmäßig aktiviert. Hiermit können Sie die Multi Core-Unterstützung für den Prozessor aktivieren oder deaktivieren. Der installierte Prozessor unterstützt zwei Cores.
Option Beschreibung Auto On Time Ermöglicht das Festlegen der Zeit zum automatischen Einschalten des Computers. Die Optionen sind: • Deaktiviert • Every Day (Jeden Tag) • Weekdays (Wochentags) • Select Days (Tage auswählen) Standardeinstellung: Disabled (Deaktiviert) USB Wake Support Ermöglicht die Aktivierung von USB-Geräten, um das System aus dem Standby-Modus zu holen. ANMERKUNG: Diese Funktion kann nur dann verwendet werden, wenn ein Netzadapter angeschlossen ist.
Option Beschreibung Primary Battery Charge Configuration Ermöglicht die Auswahl des Lademodus für den Akku. Die Optionen sind: • Adaptive (Adaptiv) – standardmäßig aktiviert. • Standard – Lädt den Akku mit einer Standardrate vollständig auf. • ExpressCharge (Schnelllademodus) – Der Akku wird innerhalb eines kurzen Zeitraums mit der Dell-Technologie zum schnellen Aufladen geladen. Diese Option ist standardmäßig aktiviert. • Primarily AC use (Primäre Wechselstromverwendung). • Benutzerdefiniert.
Option Beschreibung Full Screen Logo Warnings and Errors Sign of Life Indication (Aktivitätsanzeige) • 10 seconds (10 Sekunden) • Enable Full Screen Logo (Vollbildschirmlogo aktivieren) – deaktiviert Diese Option bewirkt, dass der Startvorgang nur angehalten wird, wenn Warnungen oder Fehler erkannt werden, anstatt zu stoppen, zu Eingaben aufzufordern und auf Eingaben vom Benutzer zu warten.
Optionen des Bildschirms „Maintenance“ (Wartung) Option Beschreibung Service Tag Zeigt die Service-Tag-Nummer des Computers an. Asset Tag Ermöglicht es, eine Systemkennnummer zu definieren, wenn noch keine festgelegt wurde. Diese Option ist standardmäßig nicht aktiviert. BIOS Downgrade Dieses Feld steuert den Flash-Vorgang der Systemfirmware auf frühere Versionen. Die Option „Allow BIOSDowngrade“ (BIOS-Downgrade gestatten) ist standardmäßig aktiviert.
SupportAssist System Resolution (SupportAssistSystemproblemlösung) Option Beschreibung Auto OS Recovery Threshold Die Einrichtungsoption „Auto OS Recovery Threshold“ (Schwellenwert für automatische Wiederherstellung des Betriebssystems) steuert den automatischen Startfluss für die SupportAssist-System-Auflösungskonsole und für das Dell OS Recovery-Tool.
Aktualisieren Ihres System-BIOS unter Verwendung eines USB-Flash-Laufwerks Falls das System nicht in Windows geladen werden kann, muss trotzdem das BIOS aktualisiert, die BIOS-Datei mit einem anderen System heruntergeladen und auf einen startfähigen USB-Flashlaufwerk gespeichert werden. ANMERKUNG: Dazu muss ein startfähiges USB-Flashlaufwerk verwendet werden. Weitere Informationen hierzu erhalten Sie im folgenden Artikel: http://www.dell.
VORSICHT: Wenn Ihr Computer nicht gesperrt und unbeaufsichtigt ist, kann jede Person auf die auf dem System gespeicherten Daten zugreifen. ANMERKUNG: System- und Setup-Kennwortfunktionen sind deaktiviert Zuweisen eines System- und Setup-Kennworts Sie können ein neues Systemkennwort nur zuweisen, wenn der Zustand Nicht festgelegt ist. Um das System-Setup aufzurufen, drücken Sie unmittelbar nach einem Einschaltvorgang oder Neustart die Taste F2.
6 Software Dieses Kapitel listet die unterstützten Betriebssysteme sowie die Anweisungen für die Installation der Treiber auf. Themen: • Konfiguration des Betriebssystems • Herunterladen von Treibern Konfiguration des Betriebssystems Dieser Abschnitt listet die Betriebssysteme auf, die unterstützt werden von Tabelle 20.
• Treiber für Intel Dynamic Platform and Thermal Framework • Intel serieller E/A-Treiber • Management Engine • Realtek PCI-E-Speicherkarte Serieller E/A-Treiber Überprüfen Sie, ob die Treiber für Touchpad, IR-Kamera und Tastatur installiert sind. Abbildung 5. Serieller E/A-Treiber Treiber für Grafikcontroller Überprüfen Sie, ob der Treiber für den Grafikcontroller bereits auf dem Computer installiert ist. Tabelle 21.
USB-Treiber Überprüfen Sie, ob die USB-Treiber bereits auf dem Computer installiert sind. Realtek Audio Überprüfen Sie, ob die Realtek Audiotreiber bereits auf dem Computer installiert sind. Tabelle 22. Realtek Audio Vor der Installation Nach der Installation Serieller ATA-Treiber Installieren Sie den neuesten Intel Rapid Storage Treiber, um optimale Leistung sicherzustellen. Die Verwendung der standardmäßigen Windows Speichertreiber wird nicht empfohlen.
Software
7 Fehlerbehebung Zurücksetzen der Echtzeituhr Mit der Funktion zum Zurücksetzen der Echtzeituhr (Real Time Clock) können Sie oder der Servicetechniker das kürzlich eingeführten Systeme Dell Latitude und Precision in bestimmten No POST/No Boot/No Power (Kein POST/Kein Start/Kein Strom) -Situationen wiederherstellen. Sie können die RTC-Zurücksetzung im ausgeschalteten Systemzustand nur initiieren, wenn das System an den Netzstrom angeschlossen ist.