Dell Latitude 5300 2-in-1 Service Manual Regulatory Model: P96G Regulatory Type: P96G001 September 2020 Rev.
Märkused, ettevaatusabinõud ja hoiatused MÄRKUS: MÄRKUS tähistab olulist teavet, mis aitab teil toodet paremini kasutada. ETTEVAATUST: ETTEVAATUST tähistab teavet, mis hoiatab võimaliku riistvarakahju või andmekao eest ja annab juhiseid selle probleemi vältimiseks. HOIATUS: HOIATUS tähistab teavet, mis hoiatab võimaliku varakahju või tervisekahjustuse või surma eest. © 2016– 2020 Dell Inc. või selle tütarettevõtted. Kõik õigused on kaitstud. Dell, EMC ja muud kaubamärgid on ettevõtte Dell Inc.
Contents Chapter 1: Arvutiga töötamine.......................................................................................................5 Ohutusjuhised....................................................................................................................................................................... 5 Enne arvuti sees toimetamist.....................................................................................................................................
Kõlarite eemaldamine..................................................................................................................................................39 Kõlarite paigaldamine.................................................................................................................................................. 42 Süsteemi ventilaator........................................................................................................................................................
1 Arvutiga töötamine Teemad: • Ohutusjuhised Ohutusjuhised Eeltingimused Et kaitsta arvutit viga saamise eest ja tagada enda ohutus, kasutage järgmisi ohutusjuhiseid. Kui pole teisiti märgitud, eeldatakse igas selle dokumendi protseduuris, et on täidetud järgmised tingimused. ● Olete lugenud arvutiga kaasas olevat ohutusteavet. ● Komponendi saab asendada või, kui see on eraldi ostetud, paigaldada eemaldamisprotseduurile vastupidises järjekorras.
4. Ühendage arvuti küljest lahti kõik võrgu- ja välisseadmed, nagu klaviatuur, hiir, monitor jne. 5. Kui arvutiga on ühendatud meediumikaarte või optilisi draive, siis eemaldage need. 6. Kui arvuti on vooluvõrgust eemaldatud, vajutage emaplaadi maandamiseks toitenuppu ja hoidke seda 5 sekundit all. ETTEVAATUST: Asetage arvuti puhtale pehmele tasasele pinnale, et ekraani mitte kriimustada. 7. Asetage arvuti pinnale nii, et ekraaniosa oleks suunaga allapoole.
ESD-paneeli eemaldamiseks tehke järgmist. ● Kasutage korralikult maandatud kaabliga ESD-randmerihma. Juhtmeta antistaatiliste rihmade kasutamine ei ole enam lubatud, sest need ei paku piisavat kaitset. Korpuse puudutamine enne osade käsitsemist ei kaitse suurema ESD-tundlikkkusega komponente piisavalt. ● Käsitsege kõiki staatilise elektri suhtes tundlikke komponente antistaatilises piirkonnas. Võimaluse korral kasutage antistaatilisi põranda- ja töölauamatte.
Tundlike komponentide transportimine ESD-tundlike osade, näiteks varuosade või Dellile tagastatavate osade vedamisel tuleb need ohutuse huvides kindlasti asetada antistaatilistesse kottidesse. Tõsteseade Raskete seadmete tõstmisel järgige järgmisi juhiseid. ETTEVAATUST: Ärge tõstke rohkem kui 22,67 kg. Kutsuge abijõude või kasutage mehhaanilist tõsteseadet. 1. Võtke kindel tasakaalustatud jalgade asend. Hoidke jalad lahus, et need oleksid stabiilse aluse eest ja suunake oma varbad välja. 2.
2 Tehnoloogia ja komponendid Selles peatükis täpsustatakse süsteemi tehnoloogiat ja saadaolevaid komponente. Teemad: • • • • USB omadused C-tüüpi USB HDMI 1.4a Toitenupu LED-i käitumine USB omadused Universal Serial Bus või USB tuli kasutusele 1996. aastal. See lihtsustas oluliselt ühendust hostarvuti ja välisseadmete vahel, nagu hiired, klaviatuurid, välisajamid ja printerid. Tabel 1. USB areng Tüüp Andmeedastuskiirus Kategooria Kasutuselevõtu aasta USB 2.0 480 Mb/s Suur kiirus 2000 USB 3.
USB 3.0 / USB 3.1 1. põlvkond saavutab allpool nimetatud tehniliste muudatustega palju parema jõudluse. ● Täiendav füüsiline siin, mis on lisatud paralleelselt olemasoleva siiniga USB 2.0 (vt allolevat pilti). ● USB 2.0-l oli varem neli juhet (toide, maandus ja paar diferentsiaalandmete jaoks); USB 3.0 / USB 3.1 1. põlvkond lisab veel neli – kaks paari diferentsiaalsignaali (vastuvõtu ja edastuse) jaoks, nii et kokku on liidestes ja juhtmes kaheksa ühendust. ● USB 3.0 / USB 3.1 1.
C-tüüpi USB C-tüüpi USB on uus füüsiline liides. Liides ise toetab erinevaid põnevaid uusi USB-standardeid, näiteks USB 3.1 ja USB toitega varustamine (USB PD). Alternatiivne režiim C-tüüpi USB on uus väga väikese suurusega liidesestandard. See on umbes kolmandik vana A-tüüpi USB kontakti suurusest. See on ühe liidese standard, mida peaks suutma kasutada iga seade.
Thunderbolt 3 C-tüüpi USB kaudu Thunderbolt 3 võtab Thunderboltis kasutusele C-tüüpi USB kiirustel kuni 40 Gbit/s, luues ühe kompaktse pordi, mis teeb kõike – see pakub kiireimat ja mitmekülgseimat ühendust mis tahes doki, kuva- või andmeseadmega (nt väline kõvaketas). Thunderbolt 3 kasutab toetatud välisseadmetega ühenduse loomiseks C-tüüpi USB liidest/porti. 1. 2. 3. 4.
● Auto ühendussüsteemid – uued kaablid ja liidesed auto videosüsteemidele, mis on mõeldud mootorsõidukite keskkonna ainulaadsete nõuete täitmiseks, pakkudes tõelist HD-kvaliteeti. HDMI eelised ● Kvaliteetne HDMI edastab tihendamata digitaalse heli ja video, tagades kõrgeima, teravaima pildikvaliteedi. ● Madalama hinnaga HDMI pakub digitaalse liidese kvaliteeti ja funktsionaalsust, toetades samal ajal ka tihendamata videovorminguid lihtsal ja kulusäästlikul moel.
Sõrmejäljelugejaga toitenupul ei ole LED-i ja sel juhul kasutatakse süsteemi oleku näitamiseks saadaolevaid LED-e. ● Toiteadapteri LED ○ Toiteadapteri pistiku LED süttib valgelt, kui adapter saab toitevõrgust voolu. ● Aku oleku LED ○ Kui arvuti on ühendatud pistikupesaga, töötab aku märgutuli järgmiselt. 1. Pidev valge: aku laeb. LED kustub, kui laadimine on lõppenud. ○ Kui arvuti töötab akutoitel, käitub aku märgutuli järgmiselt. 1. Väljas: aku on piisavalt laetud (või arvuti on välja lülitatud). 2.
3 Süsteemi peamised komponendid 1. Tagakaas 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 16 Jahutusradiaator Mälumoodulid Emaplaat Pooljuhtketas Aku Kõlar Kiipkaardilugeri paneel Randmetugi Ekraanikoost LED-paneel Puuteplaadi nupupaneel Nööppatarei WLAN-kaart WWAN-kaart Süsteemi ventilaator MÄRKUS: Ostetud süsteemi algse konfiguratsiooni komponentide loendi ja komponentide osade numbrid saate Dellilt. Need osad on saadaval kliendi ostetud garantii ulatuse kohaselt. Teabe saamiseks ostmisvõimaluste kohta pöörduge Delli müügiesindaja poole.
4 Demonteerimine ja kokkupanek MÄRKUS: Käesolevas dokumendis olevad pildid võivad olenevalt tellitud konfiguratsioonist teie arvutist erineda.
MicroSD-kaardi paigaldamine Sammud 1. Joondage microSD-kaart arvutis oleva pesaga [1]. 2. Libistage microSD-kaart pessa, kuni see paika lukustub [2].
Järgmised sammud Järgige protseduure jaotises Pärast arvuti sees toimetamist. SIM-kaardi salv SIM-kaardi salve eemaldamine Eeltingimused Järgige protseduuri jaotises Enne arvuti sees toimetamist Sammud 1. Sisestage varras SIM-kaardi salve avasse ja vajutage seda sissepoole, kuni salv avaneb [1, 2]. 2. Tõmmake SIM-kaardi salv arvutist välja [3].
SIM-kaardi salve paigaldamine Sammud 1. Asetage SIM-kaart SIM-kaardi salve, nii et metallist kontaktid on suunaga ülespoole [1]. 2. Joondage SIM-kaardi salv arvuti pesaga ja libistage see ettevaatlikult sisse [2]. 3. Lükake SIM-kaardi alus pessa, kuni kuulete klõpsu [3].
Järgmised sammud Järgige protseduure jaotises Pärast arvuti sees toimetamist tagakaas Tagakaane eemaldamine Eeltingimused 1. Järgige protseduuri jaotises Enne arvuti sees toimetamist. 2. Eemaldage microSD-kaart. Sammud 1. Keerake lahti kaheksa kruvi, millega tagakaas on kinnitatud arvuti külge.
2. Kangutage plastvarda [1] abil tagakaane vasak ülemine nurk lahti ja seejärel jätkake kangutamist mööda külgi, et avada tagakaas [2].
3. Tõstke tagakaas arvuti küljest ära.
4. Peale tagakaane eemaldamist, eemaldage SIM-kaardi kate. SIM-kaardi katte eemaldamiseks kangutage SIM-kaardi imitatsioon üle süvendpunkti, mis asub SIM-kaardi imitatsiooni ja süsteemi raami vahel. Tagakaane paigaldamine Sammud 1. Paigaldage SIM-kaardi kate ümber uue tagakaane külge. 2. Joondage arvuti tagakaas ja paigaldage see arvuti külge. 3. Vajutage tagakaane servi ja külgi, kuni see kohale klõpsatab.
4. Pingutage kaheksat kinnituskruvi, et tagakaas arvuti külge kinnitada. Järgmised sammud 1. Paigaldage microSD-kaart. 2. Järgige protseduuri jaotises Pärast arvuti sees toimetamist aku Liitiumioonaku ettevaatusabinõud ETTEVAATUST: ● Olge liitiumioonakude käsitsemisel ettevaatlik. ● Enne eemaldamist tühjendage aku täielikult. Ühendage vahelduvvoolu adapter süsteemist lahti ja kasutage arvutit ainult akutoitel – aku on täielikult tühi, kui arvuti ei lülitu enam toitenuppu vajutades sisse.
3. Keerake lahti kaks kinnituskruvi, mis kinnitavad aku randmetoe mooduli külge [1]. 4. Kergitage akut ja libistage see randmetoe moodulist välja. [2].
Aku paigaldamine Sammud 1. Joondage aku sälgud randmetoe mooduli pesadega [1]. 2. Asetage aku akusahtlisse. 3. Pingutage kaht kinnituskruvi, et kinnitada aku randmetoe külge [2].
4. Ühendage akukaabel emaplaadil olevasse pesasse [1]. 5. Kinnitage kleeplindid aku külge [2].
Järgmised sammud 1. Paigaldage tagakaas. 2. Paigaldage microSD-kaart. 3. Järgige protseduuri jaotises Pärast arvuti sees toimetamist WWAN-kaart Removing the WWAN card Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Disconnect the battery cable from the connector on the system board. Steps 1. Remove the single (M2x3) screw that secures the WWAN card bracket to the WWAN card [1]. 2.
Installing the WWAN card About this task CAUTION: To avoid damage to the WWAN card, do not place any cables under it. Steps 1. Align the notch on the WWAN card with the tab on the WWAN card slot and insert the WWAN card at an angle into the WWAN card slot [1]. 2. Connect the antenna cables to the WWAN card [2]. 3. Place the WWAN card bracket on the WWAN card [3]. 4. Replace the single (M2x3) screw to secure the WWAN card bracket to the WWAN card [4].
Next steps 1. 2. 3. 4. Connect the battery cable to the connector on the system board. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer. WLAN-kaart Removing the WLAN card Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Disconnect the battery cable from the connector on the system board. Steps 1.
Installing the WLAN card About this task CAUTION: To avoid damage to the WLAN card, do not place any cables under it. Steps 1. Insert the WLAN card into the connector on the system board [1]. 2. Connect the WLAN antenna cables to the connectors on the WLAN card [2]. 3. Place the WLAN card bracket to secure the WLAN antenna cables to the WLAN card [3]. 4. Replace the single (M2x3) screw to secure the WLAN card bracket to the WLAN card [4].
Next steps 1. 2. 3. 4. Connect the battery cable to the connector on the system board. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer. Mälumoodulid Removing the memory module Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Disconnect the battery cable from the connector on the system board. Steps 1.
Installing the memory module Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot at an angle [1]. 3. Press the memory module down until the clips secure it [2]. NOTE: If you do not hear the click, remove the memory module and reinstall it.
Next steps 1. 2. 3. 4. Connect the battery cable to the connector on the system board. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer. SSD (pooljuhtketas) Removing the M.2 SSD Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Disconnect the battery cable from the connector on the system board. Steps 1. Remove the two (M2x3) screws that secure the M.
3. Remove the single (M2x2) screw that secures the M.2 SSD to the palmrest [1]. 4. Lift the M.2 SSD away from the computer [2].
Installing the M.2 SSD Steps 1. Place the M.2 SSD into the slot on the palmrest [1]. 2. Replace the single (M2x2) screw to secure the M.2 SSD to the palmrest [2].
3. Align and place the SSD support bracket above the M.2 SSD [1]. 4. Replace the two (M2x3) screws to secure the SSD support bracket to the palmrest [2].
Next steps 1. 2. 3. 4. Connect the battery cable to the connector on the system board. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer. Kõlarid Kõlarite eemaldamine Eeltingimused 1. 2. 3. 4. Järgige protseduuri jaotises Enne arvuti sees toimetamist. Eemaldage microSD-kaart Eemaldage tagakaas. Eemaldage aku. Sammud 1. Eemaldage kõlarikaabel emaplaadil olevast pesast [1]. 2. Eemaldage kleeplint, mis hoiab kõlarikaablit randmetoe [2] küljes.
3. Eemaldage puuteplaadi kaabel alamplaadi pesast. 4. Eemaldage kleeplindid ja eemaldage kõlarikaabel juhikutest.
5. Tõstke ja eemaldage kõlarid randmetoe küljest.
Kõlarite paigaldamine Sammud 1. Asetage joonduspostide ja kummirõngaste abil kõlarid randmetoel asuvatesse pesadesse.
2. Paigaldage kõlarikaabel juhikutesse.
3. Kinnitage kleeplint, et fikseerida kõlarikaabel randmetoe [1] külge. 4. Ühendage kõlarikaabel emaplaadil olevasse pesasse [2].
Järgmised sammud 1. 2. 3. 4. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Süsteemi ventilaator Süsteemi ventilaatori eemaldamine Eeltingimused 1. 2. 3. 4. Järgige protseduuri jaotises Enne arvuti sees toimetamist. Eemaldage microSD-kaart Eemaldage tagakaas. Eemaldage aku. Sammud 1. Eemaldage süsteemi ventilaatori kaabel emaplaadil olevast pesast.
2. Eemaldage kaks (M2 × 5) kruvi, mis hoiavad süsteemi ventilaatorit randmetoe [1] küljes. 3. Tõstke süsteemi ventilaator arvuti küljest ära [2].
Süsteemi ventilaatori paigaldamine Sammud 1. Joondage süsteemi ventilaatori kruviaugud randmetoel [1] olevate kruviaukudega. 2. Paigaldage kaks (M2 × 5) kruvi, et kinnitada süsteemi ventilaator randmetoe külge [2].
3. Ühendage süsteemi ventilaatori kaabel emaplaadil olevasse pesasse.
Järgmised sammud 1. 2. 3. 4. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Jahutusradiaator Jahutusradiaatori eemaldamine Eeltingimused 1. 2. 3. 4. Järgige protseduuri jaotises Enne arvuti sees toimetamist. Eemaldage microSD-kaart. Eemaldage tagakaas. Eemaldage aku. Sammud 1. Keerake lahti neli küljespüsivat kruvi, mis hoiavad jahutusradiaatorit emaplaadi küljes [1].
Jahutusradiaatori paigaldamine Sammud 1. Asetage jahutusradiaator emaplaadile ja joondage selle kruviaugud emaplaadi kruviaukudega [1]. 2. Keerake jahutusradiaatorit emaplaadiga ühendavad neli küljespüsivatkruvi järjestikku kinni, nagu jahutusradiaatoril on näidatud [2].
Järgmised sammud 1. 2. 3. 4. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist alalisvoolusisendi port Removing the DC-in port Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Remove the battery. Steps 1. Remove the two (M2x4) screws that secure the Type-C bracket to the system board [1]. 2. Lift the Type-C bracket away from the computer [2].
3. Press the DC-in port cable and then pull the cable horizontally to disconnect the DC-in port cable from the connector on the system board [1]. Lift the DC-in port away from the computer [2].
Installing the DC-in port Steps 1. Place the DC-in port to its slot on the computer [1]. 2. Connect the DC-in port cable to the connector on the system board [2].
3. Place the Type-C bracket on its slot on the computer [1]. 4. Replace the two (M2x4) screws to secure the Type-C bracket to the palmrest [2].
Next steps 1. 2. 3. 4. Replace the battery. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer. LED-paneel Removing the LED board Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Remove the battery. Steps 1. Disconnect the LED board cable from the connector on the system board [1]. 2. Unroute the LED board cable [2].
3. Peel the adhesive tape that secures the LED board cable connector to the LED board [1]. 4. Peel the grey adhesive tape that secures the LED board [2].
5. Remove the single (M2x2.5) screw that secures the LED board to the palmrest [1]. 6. Lift the LED board away from the computer [2].
LED-paneeli paigaldamine Sammud 1. Paigaldage LED-paneel ning joondage LED-paneeli kruviauk randmetoel oleva kruviauguga [1]. 2. Paigaldage üks (M2 × 2,5) kruvi, mis hoiab LED-paneeli randmetoe [2] küljes.
3. Paigaldage LED-paneeli kinnitamiseks hall kleeplint [1]. 4. Kinnitage kleeplint, et fikseerida LED-paneel [2].
5. Ühendage LED-paneeli kaabel emaplaadi pistikupessa ja paigaldage LED-paneeli kaabel juhikutesse [1, 2].
Järgmised sammud 1. 2. 3. 4. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Puuteplaadi nupupaneel Puuteplaadi nupupaneeli eemaldamine Eeltingimused 1. 2. 3. 4. 5. 6. Järgige protseduuri jaotises Enne arvuti sees toimetamist. Eemaldage microSD-kaart Eemaldage tagakaas. Eemaldage aku. Eemaldage kõlar. Eemaldage LED-paneel. MÄRKUS: Puuteplaadi nupupaneeli eemaldamiseks ei ole emaplaadi ega jahutusradiaatori eemaldamine vajalik.
2. Eemaldage kaks kruvi (M2 × 3), mis kinnitavad puuteplaadi nupupaneeli klambri randmetoe [1] külge. 3. Tõstke puuteplaadi nupupaneeli klamber arvuti küljest ära [2].
Puuteplaadi nupupaneeli paigaldamine Sammud 1. Asetage puuteplaadi nupupaneel randmetoel olevasse pesasse [1]. 2. Paigaldage kaks kruvi (M2 × 3), mis kinnitavad puuteplaadi nupupaneeli randmetoe [2] külge.
3. Ühendage puuteplaadi nupupaneeli kaabel puuteplaadi paneeli pesasse .
Järgmised sammud 1. 2. 3. 4. 5. 6. Paigaldage LED-paneel. Paigaldage kõlar. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Emaplaat Removing the system board Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Remove the battery. Remove the speaker. Remove the heatsink. Remove the memory module. Remove the system fan.
Steps 1. Remove the three (M2x3) screws that secure the memory module frame to the system board [1]. 2. Remove the memory module frame away from the computer [2]. 3. Disconnect the following cables: a. USH cable [1]. b. LED board cable [2]. c. touchpad cable [3].
4. Remove the single (M2.5x4) screw that secures the fingerprint support bracket to the system board [1]. 5. Lift the fingerprint support bracket away from the computer [2]. 6. Disconnect the fingerprint port [3].
7. Peel the adhesive tape and disconnect the cable from the connector on the system board [1]. 8. Peel the adhesive tape that secures the eDP bracket [2]. 9. Remove the single (M2x4) screw that secures the eDP bracket to the system board [3]. 10. Remove the eDP bracket away from the computer [4]. 11. Lift the latch and disconnect the eDP cable from the connector on the system board [5].
12. Disconnect the sensor board cable from the connector on the system board [1]. 13. Release the coin cell battery from the palmrest [2].
14. Remove the single (M2.5x4) screw that secures the system board to the palmrest [1]. 15. Lift the system board away from the computer [2].
Installing the system board Steps 1. Align and place the system board to the palmrest [1]. 2. Replace the single (M2.5x4) screw to secure the system board to the palmrest [2].
3. Connect the sensor cable to the connector on the system board [1]. 4. Place the coin cell battery into its slot on the plamrest [2].
5. Connect the cable to the connector on the system board and adhere the adhesive tape [1]. 6. Connect the eDP cable to the connector on the system board [2]. 7. Place the eDP support bracket above the eDP connector [3]. 8. Replace the single (M2x4) screw to secure the eDP bracket to the system board [4]. 9. Adhere the adhesive tape to secure the eDP support bracket [5].
10. Connect the fingerprint cable to the connector on the system board [1]. 11. Place the fingerprint support bracket [2]. 12. Replace the single (M2.5x4) screw to secure the fingerprint support bracket to the system board [3].
13. Connect the following cables: a. USH cable [1]. b. LED board cable [2]. c. touchpad cable [3].
14. Align and place the memory module frame in its slot on the system board [1]. 15. Replace the three (M2x3) screws to secure the memory module frame to the system board [2].
Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Replace the WWAN card. Replace the WLAN card. Replace the Dc-in. Replace the memory module. Replace the system fan. Replace the heatsink. Replace the speaker. Replace the battery. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer.
Nööppatarei Nööppatarei eemaldamine Eeltingimused 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Järgige protseduuri jaotises Enne arvuti sees toimetamist. Eemaldage microSD-kaart. Eemaldage tagakaas. Eemaldage aku. Eemaldage kõlar. Eemaldage jahutusradiaator. Eemaldage mälumoodul. Eemaldage süsteemi ventilaator. Eemaldage alalisvoolusisend. Eemaldage WLAN-kaart. Eemaldage WWAN-kaart. Eemaldage emaplaat. Sammud Pöörake emaplaati ja eemaldage nööppatarei kaabel emaplaadil olevast pesast.
Järgmised sammud 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Ühendage emaplaat. Paigaldage WWAN-kaart. Paigaldage WLAN-kaart. Paigaldage alalisvoolusisend. Ühendage mälumoodul. Paigaldage süsteemi ventilaator. Paigaldage jahutusradiaator. Paigaldage kõlar. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Ekraanisõlm Ekraanisõlme eemaldamine Eeltingimused 1. 2. 3. 4. Järgige protseduuri jaotises Enne arvuti sees toimetamist.
Sammud 1. Eemaldage kleeplint ja eemaldage kaabel emaplaadil olevast pesast [1]. 2. Eemaldage üks (M2 × 4) kruvi, mis kinnitab eDP-kaabli klambri emaplaadi [2] külge. 3. Tõstke eDP-kaabli klamber emaplaadilt ära [3]. 4. Eemaldage ja vabastage eDP-kaabel [4]. 5. Avage ekraanisõlm 180-kraadise nurga all, keerake süsteem teistpidi ning asetage see tasasele pinnale.
6. Eemaldage neli (M2,5 × 4) kruvi, mis kinnitavad ekraanisõlme süsteemi raami [1] külge. 7. Eemaldage ekraanisõlm süsteemi [2] küljest.
Ekraanisõlme paigaldamine See ülesanne MÄRKUS: Veenduge, et hinged oleksid maksimaalselt avatud, enne kui paigaldate ekraanisõlme randmetoe- ja klaviatuurimooduli külge. Sammud 1. Joondage süsteemi raam ja asetage see ekraanisõlme hingede alla [1]. 2. Paigaldage neli (M2,5 × 4) kruvi, mis kinnitavad ekraanisõlme süsteemi raami [2] külge.
3. Paigaldage süsteemi raam ekraanisõlme külge.
4. Ühendage kaabel emaplaadi pistikupesasse ja kinnitage kleeplint [1]. 5. Paigaldage eDP-kaabel juhikutesse ja ühendage see eDP-pistikupessa [2]. 6. Paigaldage eDP-kaabli klamber emaplaadi [3] külge. 7. Paigaldage üks (M2 × 4) kruvi, mis hoiab eDP-kaardi klambrit emaplaadi küljes [4].
Järgmised sammud 1. 2. 3. 4. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist Klaviatuur Removing the keyboard Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. Follow the procedure in before working inside your computer. Remove the microSD card. Remove the base cover. Remove the battery. Remove the speaker. Remove the memory module. Remove the system fan. Remove the DC-in . Remove the WLAN card.
10. Remove the WWAN card. 11. Remove the system board. NOTE: System board can be removed with heatsink attached. 12. Remove the coin cell battery. Steps 1. Peel the adhesive tape securing the keyboard and the smartcard reader. 2. Lift the latch and disconnect the backlit cable and the keyboard cables from the connectors on the touchpad.
3. Remove the 19 (M2x2) screws that secure the keyboard to the palmrest [1]. 4. Remove the keyboard away from the computer [2].
Installing the keyboard Steps 1. Align and place the keyboard on the palmrest [1]. 2. Replace the 19 (M2x2) screws to secure the keyboard to the palmrest [2].
3. Connect the backlit cable and the keyboard cables to the connectors on the touchpad.
4. Adhere the adhesive tape securing the keyboard and the smartcard board.
Next steps 1. Replace the coin cell battery. 2. Replace the system board. NOTE: System board can be replaced with heatsink attached. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Replace the WWAN card. Replace the WLAN card. Replace the DC-in. Replace the system fan. Replace the memory module. Replace the speaker. Replace the battery. Replace the base cover. Replace the microSD card. Follow the procedure in after working inside your computer.
2. Eemaldage kaks (M2 × 2,5) kruvi, mis kinnitavad kiipkaardilugeja randmetoe [1] külge. 3. Tõstke kiipkaardilugeja paneel arvutist [2] välja.
Kiipkaardilugeja paneeli paigaldamine Sammud 1. Joondage kiipkaardilugeja paneel ja asetage see randmetoe [1] külge. 2. Paigaldage kaks (M2 × 2,5) kruvi, mis kinnitavad kiipkaardilugeja randmetoe [2] külge.
3. Paigaldage kiirkaardilugeja kaabel juhikutesse.
Järgmised sammud 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Paigaldage nööppatarei. Ühendage emaplaat. Paigaldage WWAN-kaart. Paigaldage WLAN-kaart. Paigaldage alalisvoolusisend. Ühendage mälumoodul. Paigaldage süsteemi ventilaator. Paigaldage kõlar. Paigaldage aku. Paigaldage tagakaas. Paigaldage microSD-kaart. Järgige protseduuri jaotises Pärast arvuti sees toimetamist. Randmetoe koost Replacing the palmrest and keyboard assembly Prerequisites 1. 2. 3. 4. 5. 6.
7. 8. 9. 10. 11. Remove Remove Remove Remove Remove the the the the the system fan. DC-in . WLAN card. WWAN card. system board. NOTE: System board can be removed with heatsink attached. 12. Remove the coin cell battery. 13. Remove the SmartCard reader board. About this task After performing the preceding steps, you are left with the palmrest and keyboard assembly. Next steps 1. Replace the SmartCard reader board. 2. Replace the coin cell battery. 3. Replace the system board.
5 Tõrkeotsing Teemad: • • • Dell SupportAssisti algkäivituseelse süsteemi toimivuse kontrolli diagnostika Süsteemi diagnostika märgutuled Wi-Fi-toitetsükkel Dell SupportAssisti algkäivituseelse süsteemi toimivuse kontrolli diagnostika See ülesanne SupportAssisti tugidiagnostika (nimetatakse ka süsteemidiagnostikaks) teeb täieliku riistvarakontrolli. SupportAssisti algkäivituseelse süsteemi toimivuse kontrolli diagnostika on manustatud BIOS-i ja BIOS käivitab selle sisemiselt.
Toite ja aku oleku märgutuli näitab arvuti toite ja aku olekut. Toite olekud on järgmised: Ühtlane valge: toiteadapter on ühendatud ja aku laetuse tase on üle 5%. Merevaigukollane: arvuti töötab akutoitel ja aku laetuse tase on alla 5%. Väljas ● Toiteadapter on ühendatud ja aku on täielikult laetud. ● Arvuti töötab akutoitel ja aku laetuse tase on alla 5%. ● Arvuti on unerežiimis, talveunerežiimis või välja lülitatud.
5. Lülitage traadita ruuter sisse. 6. Lülitage modem sisse. 7. Lülitage arvuti sisse.
6 Abi saamine Teemad: • Delli kontaktteave Delli kontaktteave Eeltingimused MÄRKUS: Kui teil pole aktiivset Interneti-ühendust, võite leida kontaktteavet oma ostuarvelt, saatelehelt, tšekilt või Delli tootekataloogist. See ülesanne Dell pakub mitmeid veebipõhiseid ja telefonipõhiseid tugi- ning teenusevõimalusi. Saadavus võib riigi ja toote järgi erineda, mõned teenused ei pruugi olla teie piirkonnas saadaval. Delliga müügi, tehnilise toe või klienditeeninduse küsimustes ühenduse võtmiseks tehke järgmist.