Dell Latitude 5300 2 w 1 Instrukcja serwisowa Model regulacji: P96G Typ regulacji: P96G001 September 2020 Wer.
Uwagi, przestrogi i ostrzeżenia UWAGA: Napis UWAGA oznacza ważną wiadomość, która pomoże lepiej wykorzystać komputer. OSTRZEŻENIE: Napis PRZESTROGA informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu lub utraty danych, i przedstawia sposoby uniknięcia problemu. PRZESTROGA: Napis OSTRZEŻENIE informuje o sytuacjach, w których występuje ryzyko uszkodzenia sprzętu, obrażeń ciała lub śmierci. © 2016– 2020 Dell Inc. lub podmioty zależne. Wszelkie prawa zastrzeżone.
Spis treści Rodzdział 1: Serwisowanie komputera...............................................................................................5 Instrukcje dotyczące bezpieczeństwa................................................................................................................................ 5 Przed przystąpieniem do serwisowania komputera.................................................................................................... 5 Zalecenia dotyczące bezpieczeństwa...................
Wymontowywanie głośników.......................................................................................................................................39 Instalowanie głośników..................................................................................................................................................42 Wentylator systemowy.......................................................................................................................................................
1 Serwisowanie komputera Tematy: • Instrukcje dotyczące bezpieczeństwa Instrukcje dotyczące bezpieczeństwa Wymagania Aby uchronić komputer przed uszkodzeniem i zapewnić sobie bezpieczeństwo, należy przestrzegać następujących zaleceń dotyczących bezpieczeństwa. O ile nie wskazano inaczej, każda procedura opisana w tym dokumencie opiera się na założeniu, że są spełnione następujące warunki: ● Użytkownik zapoznał się z informacjami dotyczącymi bezpieczeństwa, jakie zostały dostarczone z komputerem.
2. Wyłącz komputer. Kliknij kolejno opcje Start > Zasilanie > Wyłącz. UWAGA: Jeśli używasz innego systemu operacyjnego, wyłącz urządzenie zgodnie z instrukcjami odpowiednimi dla tego systemu. 3. Odłącz komputer i wszystkie urządzenia peryferyjne od gniazdek elektrycznych. 4. Odłącz od komputera wszystkie urządzenia sieciowe i peryferyjne, np. klawiaturę, mysz, monitor itd. 5. Wyjmij z komputera wszystkie karty pamięci i dyski optyczne. 6.
● Katastrofalne — zdarzenia tego typu stanowią około 20 procent awarii związanych z wyładowaniami elektrostatycznymi. Uszkodzenie powoduje natychmiastową i całkowitą utratę funkcjonalności urządzenia. Przykładem katastrofalnej awarii może być moduł DIMM, który uległ wstrząsowi elektrostatycznemu i generuje błąd dotyczący braku testu POST lub braku sygnału wideo z sygnałem dźwiękowym oznaczającym niedziałającą pamięć.
zakleić. Należy również użyć tej samej pianki i opakowania, w którym dostarczono nową część. Urządzenia wrażliwe na wyładowania elektrostatyczne należy po wyjęciu z opakowania umieścić na powierzchni roboczej zabezpieczonej przed ładunkami elektrostatycznymi. Nie wolno kłaść części na zewnętrznej powierzchni torby antyelektrostatycznej, ponieważ tylko jej wnętrze jest ekranowane. Części należy zawsze trzymać w ręce albo umieścić na macie antystatycznej, w systemie lub wewnątrz torby antyelektrostatycznej.
2 Technologia i podzespoły Niniejszy rozdział zawiera szczegółowe informacje dotyczące technologii i składników dostępnych w systemie. Tematy: • • • • Funkcje USB USB Type-C HDMI 1.4a Zachowanie diody LED przycisku zasilania Funkcje USB Standard uniwersalnej magistrali szeregowej USB (Universal Serial Bus) został wprowadzony w 1996 r. Interfejs ten znacznie uprościł podłączanie do komputerów hostów urządzeń peryferyjnych, takich jak myszy, klawiatury, napędy zewnętrzne i drukarki. Tabela 1.
Znacznie wyższa wydajność złącza USB 3.0/3.1 pierwszej generacji jest możliwa dzięki następującym zmianom technologicznym: ● Dodatkowa fizyczna magistrala istniejącą równolegle do bieżącej magistrali USB 2.0 (patrz zdjęcie poniżej). ● Złącze USB 2.0 miało cztery przewody (zasilania, uziemienia oraz parę przewodów do danych różnicowych); złącze USB 3.0/3.
generacji znajduje się pięć nowych połączeń odpowiedzialnych za niezależny odbiór i nadawanie danych, które są aktywowane po podłączeniu do odpowiedniego złącza SuperSpeed USB. USB Type-C USB Type-C to nowe, małe złącze fizyczne. Obsługuje ono różne nowe standardy USB, takie jak USB 3.1 i USB Power Delivery (USB PD). Tryb alternatywny USB Type-C to nowe, bardzo małe złącze. Jest mniej więcej trzy razy mniejsze od dawnych złączy USB Type-A.
1. Thunderbolt 1 i Thunderbolt 2 (ze złączem miniDP) 2. Thunderbolt 3 (ze złączem USB Type-C) Thunderbolt 3 przez USB Type-C Standard Thunderbolt 3 dodaje technologię Thunderbolt do złącza USB Type-C, pozwalając przesyłać dane z szybkością nawet 40 Gb/s. W ten sposób staje się pojedynczym, uniwersalnym portem, który zapewnia najszybsze i najbardziej wszechstronne połączenie ze stacjami dokującymi, wyświetlaczami czy urządzeniami do przechowywania danych, takimi jak zewnętrzne dyski twarde.
● Dodatkowe przestrzenie barw – wprowadza obsługę dodatkowych modeli barw stosowanych w fotografii cyfrowej i grafice komputerowej. ● Obsługa standardu 4K — umożliwia przesyłanie obrazu w rozdzielczości znacznie wyższej niż 1080p do wyświetlaczy nowej generacji, które dorównują jakością systemom Digital Cinema stosowanym w wielu komercyjnych kinach. ● Złącze HDMI Micro — nowe, mniejsze złącze dla telefonów i innych urządzeń przenośnych, obsługujące rozdzielczość do 1080p.
Przycisk zasilania z czytnikiem linii papilarnych w przycisku zasilania nie ma diody LED, więc informacje o systemie są wskazywane przez inne dostępne diody ● Wskaźnik zasilacza: ○ Wskaźnik na złączu zasilacza świeci kolorem białym, gdy jest podłączone zasilanie z gniazdka elektrycznego. ● Wskaźnik baterii: ○ Jeśli komputer jest podłączony do gniazdka elektrycznego, lampka stanu akumulatora zachowuje się w następujący sposób: 1. Ciągłe białe światło: trwa ładowanie akumulatora.
3 Główne elementy systemu 1. Pokrywa dolna 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 16 Radiator Moduły pamięci Płyta systemowa Dysk SSD Akumulator Głośnik Płyta czytnika kart smart Podpórka na nadgarstek Zestaw wyświetlacza płyta wskaźników LED Płyta przycisków tabliczki dotykowej Bateria pastylkowa Karta sieci WLAN karta WWAN Wentylator systemowy UWAGA: Firma Dell udostępnia listę elementów i ich numery części w zakupionej oryginalnej konfiguracji systemu. Dostępność tych części zależy od gwarancji zakupionych przez klienta.
4 Demontowanie i montowanie UWAGA: W zależności od zamówionej konfiguracji posiadany komputer może wyglądać nieco inaczej niż na ilustracjach w tym dokumencie.
Instalowanie karty microSD Kroki 1. Włóż kartę microSD do gniazda w komputerze [1]. 2. Wsuń kartę microSD do gniazda, aż zatrzyma się z kliknięciem [2].
Kolejne kroki Wykonaj procedury przedstawione w rozdziale Po zakończeniu serwisowania komputera. Uchwyt karty SIM Wymontowywanie tacy karty SIM Wymagania Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Kroki 1. Włóż szpilkę do otworu tacy karty SIM i wepchnij ją, aż obsada zostanie zwolniona [1, 2]. 2. Wyjmij obsadę karty SIM z komputera [3].
Instalowanie tacy karty SIM Kroki 1. Włóż kartę SIM do obsady karty SIM metalowymi stykami do góry [1]. 2. Ostrożnie wsuń obsadę karty SIM do gniazda w komputerze [2]. 3. Wsuń obsadę karty SIM do gniazda, aż usłyszysz kliknięcie [3].
Kolejne kroki Wykonaj procedury przedstawione w rozdziale Po zakończeniu serwisowania komputera. pokrywa dolna Wymontowywanie pokrywy dolnej Wymagania 1. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. 2. Wyjmij kartę microSD. Kroki 1. Poluzuj osiem śrub mocujących pokrywę dolną do komputera.
2. Rysikiem z tworzywa sztucznego [1] podważ pokrywę dolną, zaczynając w lewym górnym rogu i kontynuując wzdłuż boków, aby otworzyć pokrywę dolną [2].
3. Zdejmij pokrywę dolną z komputera.
4. Po wymontowaniu pokrywy dolnej zdejmij pokrywę karty SIM. Aby wymontować pokrywę karty SIM, podważ zaślepkę karty w zagłębieniu między zaślepką a obudową systemu. Instalowanie pokrywy dolnej Kroki 1. Przenieś pokrywę karty SIM do nowej pokrywy dolnej. 2. Załóż pokrywę dolną na komputer. 3. Dociśnij krawędzie i boki pokrywy dolnej, aby ją osadzić na miejscu.
4. Dokręć osiem śrub mocujących pokrywę dolną do komputera. Kolejne kroki 1. Zainstaluj kartę microSD. 2. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Akumulator Środki ostrożności dotyczące baterii litowo-jonowej OSTRZEŻENIE: ● Podczas obsługi baterii litowo-jonowej zachowaj ostrożność. ● Przed wymontowaniem baterii należy ją całkowicie rozładować. Odłącz zasilacz prądu zmiennego od komputera i pracuj z komputerem wyłącznie na zasilaniu bateryjnym.
3. Poluzuj dwie śruby mocujące baterię do zestawu podpórki na nadgarstek [1]. 4. Wysuń baterię z zestawu podpórki na nadgarstek [2].
Instalowanie baterii Kroki 1. Dopasuj zaczepy baterii do szczelin w zestawie podpórki na nadgarstek [1]. 2. Umieść baterię w kieszeni baterii. 3. Wkręć dwie śruby mocujące baterię do podpórki na nadgarstek [2].
4. Podłącz kabel baterii do płyty systemowej [1]. 5. Przymocuj baterię taśmami samoprzylepnymi [2].
Kolejne kroki 1. Zamontuj pokrywę dolną. 2. Zainstaluj kartę microSD. 3. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Karta sieci WWAN Wymontowywanie karty sieci WWAN Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Odłącz kabel baterii od złącza na płycie głównej. Kroki 1. Wykręć śrubę (M2x3) mocującą klamrę karty sieci WWAN do samej karty [1]. 2.
Instalowanie karty sieci WWAN Informacje na temat zadania OSTRZEŻENIE: Aby uniknąć uszkodzenia karty sieci WWAN, nie należy umieszczać pod nią żadnych kabli. Kroki 1. Dopasuj wycięcie na karcie sieci WWAN do wypustki w gnieździe karty sieci WWAN i wsuń kartę do gniazda pod kątem [1]. 2. Podłącz kable antenowe do karty sieci WWAN [2]. 3. Załóż metalową klamrę na moduł karty sieci WWAN [3]. 4. Wkręć śrubę (M2x3), aby zamocować klamrę karty sieci WWAN do karty sieci WWAN [4].
Kolejne kroki 1. 2. 3. 4. Podłącz kabel baterii do złącza na płycie głównej. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Karta sieci WLAN Wymontowywanie karty sieci WLAN Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Odłącz kabel baterii od złącza na płycie głównej. Kroki 1.
Instalowanie karty sieci WLAN Informacje na temat zadania OSTRZEŻENIE: Aby uniknąć uszkodzenia kart sieci WLAN, nie należy umieszczać pod kartą żadnych kabli. Kroki 1. Umieść kartę WLAN w złączu na płycie głównej [1]. 2. Podłącz kable antenowe WLAN do złączy na karcie sieci WLAN [2]. 3. Załóż klamrę karty sieci WLAN, aby przymocować do tej karty kable antenowe WLAN [3]. 4. Wkręć śrubę (M2x3), aby zamocować klamrę karty sieci WLAN do karty sieci WLAN [4].
Kolejne kroki 1. 2. 3. 4. Podłącz kabel baterii do złącza na płycie głównej. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Moduły pamięci Wymontowywanie modułu pamięci Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Odłącz kabel baterii od złącza na płycie głównej. Kroki 1.
Instalowanie modułu pamięci Kroki 1. Dopasuj wycięcie w module pamięci do wypustki w gnieździe. 2. Wsuń moduł pamięci do gniazda pod kątem [1]. 3. Dociśnij moduł pamięci, aby zatrzaski mocujące zabezpieczyły moduł [2]. UWAGA: Jeśli nie usłyszysz kliknięcia, wyjmij moduł pamięci i zainstaluj go ponownie.
Kolejne kroki 1. 2. 3. 4. Podłącz kabel baterii do złącza na płycie głównej. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Dysk SSD Wymontowywanie karty SSD M.2 Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Odłącz kabel baterii od złącza na płycie głównej. Kroki 1.
3. Wykręć śrubę (M2x2) mocującą kartę SSD M.2 do podpórki na nadgarstek [1]. 4. Wyjmij kartę SSD M.2 z komputera [2].
Instalowanie dysku M.2 SSD Kroki 1. Włóż kartę SSD M.2 do gniazda w podpórce na nadgarstek [1]. 2. Wkręć śrubę (M2x2) mocującą kartę SSD M.2 do podpórki na nadgarstek [2].
3. Umieść klamrę karty SSD M.2 na samej karcie [1]. 4. Wkręć dwie śruby (M2x3) mocujące klamrę karty SSD do podpórki na nadgarstek [2].
Kolejne kroki 1. 2. 3. 4. Podłącz kabel baterii do złącza na płycie głównej. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Głośniki Wymontowywanie głośników Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Kroki 1. Odłącz kabel głośnikowy od płyty systemowej [1]. 2.
3. Odłącz kabel tabliczki dotykowej od złącza na płycie rozszerzenia. 4. Odklej taśmy samoprzylepne i wyjmij kabel głośnikowy .
5. Wyjmij głośniki z podparcia dłoni.
Instalowanie głośników Kroki 1. Umieść głośniki w gniazdach w podpórce na nadgarstek, dopasowując je do wypustek i gumowych krążków.
2. Umieść kabel głośników w prowadnicach.
3. Przyklej taśmę mocującą kabel głośnikowy do podpórki na nadgarstek [1]. 4. Podłącz kabel głośnikowy do płyty głównej [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj baterię. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Wentylator systemowy Wymontowywanie wentylatora systemowego Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Kroki 1. Odłącz kabel wentylatora systemowego od płyty systemowej.
2. Wykręć dwie śruby (M2x5) mocujące wentylator systemowy do podparcia dłoni [1]. 3. Wyjmij wentylator systemowy z komputera [2].
Instalowanie wentylatora systemowego Kroki 1. Wyrównaj otwory na śruby w wentylatorze systemowym z otworami w podparciu dłoni [1]. 2. Wkręć dwie śruby (M2x5) mocujące wentylator systemowy do podparcia dłoni [2].
3. Podłącz kabel wentylatora systemowego do płyty systemowej.
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Radiator Wymontowywanie radiatora Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Kroki 1. Poluzuj cztery śruby mocujące radiator do płyty systemowej [1].
Instalowanie radiatora Kroki 1. Umieść radiator na płycie systemowej i dopasuj otwory na śruby w radiatorze do otworów w płycie systemowej [1]. 2. W kolejności wskazanej na radiatorze dokręć cztery śruby mocujące radiator do płyty systemowej [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Złącze zasilania prądem stałym Wymontowywanie portu zasilania prądem stałym Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wyjmij baterię. Kroki 1.
3. Naciśnij kabel portu zasilania prądem stałym, a następnie pociągnij kabel w poziomie, aby odłączyć kabel portu zasilania prądem stałym od złącza na płycie głównej [1]. Wyjmij port zasilania prądem stałym z komputera [2].
Instalowanie portu zasilania prądem stałym Kroki 1. Włóż złącze zasilania do gniazda w komputerze [1]. 2. Podłącz kabel złącza zasilania do złącza na płycie głównej [2].
3. Umieść wspornik portu Type-C w gnieździe w komputerze [1]. 4. Wkręć dwie śruby (M2x4) mocujące wspornik portu Type-C do podpórki na nadgarstek [2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj baterię. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Płyta wskaźników LED Wymontowywanie płyty wskaźników LED Wymagania 1. 2. 3. 4. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wyjmij baterię. Kroki 1. Odłącz kabel płyty wskaźników LED od płyty głównej [1]. 2.
3. Odklej taśmę mocującą złącze kabla płyty wskaźników LED do samej płyty [1]. 4. Odklej szarą taśmę mocującą płytę wskaźników LED [2].
5. Wykręć śrubę (M2x2,5) mocującą płytę wskaźników LED do podpórki na nadgarstek [1]. 6. Wyjmij płytę wskaźników LED z komputera [2].
Instalowanie płyty wskaźników LED Kroki 1. Umieść płytę LED i wyrównaj otwory na śruby w płycie z otworami w podparciu dłoni [1]. 2. Wkręć jedną śrubę (M2x2,5) mocującą płytę LED do podparcia dłoni [2].
3. Przyklej szarą taśmę mocującą płytę LED [1]. 4. Przyklej taśmę mocującą płytę LED [2].
5. Podłącz kabel płyty LED do złącza na płycie systemowej i poprowadź go odpowiednio [1, 2].
Kolejne kroki 1. 2. 3. 4. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Płyta przycisków tabliczki dotykowej Wymontowywanie płyty przycisków tabliczki dotykowej Wymagania 1. 2. 3. 4. 5. 6. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj głośnik. Wymontuj płytę LED.
2. Wykręć dwie śruby (M2x3) mocujące wspornik płyty przycisków tabliczki dotykowej do podparcia dłoni [1]. 3. Zdejmij wspornik płyty przycisków tabliczki dotykowej z komputera [2].
Instalowanie płyty przycisków touchpada Kroki 1. Umieść płytę przycisków touchpada w gnieździe w podpórce na nadgarstek [1]. 2. Wkręć dwie śruby (M2x3) mocujące płytę przycisków touchpada do podpórki na nadgarstek [2].
3. Podłącz kabel płyty przycisków touchpada do złącza na touchpadzie .
Kolejne kroki 1. 2. 3. 4. 5. 6. Zainstaluj płytę wskaźników LED. Zainstaluj głośnik. Zainstaluj akumulator. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Płyta główna Wymontowywanie płyty głównej Wymagania 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wyjmij baterię. Wymontuj głośnik.
Kroki 1. Wykręć trzy śruby (M2x3) mocujące ramkę modułu pamięci do płyty głównej [1]. 2. Wyjmij klamrę modułu pamięci z komputera [2]. 3. Odłącz następujące kable: a. kabel USH [1] b. kabel płyty LED [2]. c. kabel touchpada [3].
4. Wykręć śrubę (M2,5x4) mocującą klamrę czytnika linii papilarnych do płyty głównej [1]. 5. Wyjmij klamrę czytnika linii papilarnych z komputera [2]. 6. Odłącz złącze czytnika linii papilarnych [3].
7. Odklej taśmę samoprzylepną i odłącz kabel od złącza na płycie głównej [1]. 8. Odklej taśmę mocującą klamrę eDP [2]. 9. Wykręć śrubę (M2x4) mocującą klamrę eDP do płyty głównej [3]. 10. Wyjmij klamrę eDP z komputera [4]. 11. Otwórz zatrzask i odłącz kabel eDP od płyty głównej [5].
12. Odłącz kabel płyty czujników od płyty głównej [1]. 13. Wyjmij baterię pastylkową z podpórki na nadgarstek [2].
14. Wykręć śrubę (M2,5x4) mocującą płytę główną do podpórki na nadgarstek [1]. 15. Wyjmij płytę główną z komputera [2].
Instalowanie płyty głównej Kroki 1. Dopasuj i umieść płytę główną w podpórce na nadgarstek [1]. 2. Wkręć jedną śrubę (M2,5x4) mocującą płytę główną do podpórki na nadgarstek [2].
3. Podłącz kabel czujnika do złącza na płycie głównej [1]. 4. Włóż baterię pastylkową do gniazda w podpórce na nadgarstek [2].
5. Podłącz kabel do złącza na płycie głównej i przyklej mocującą go taśmę [1]. 6. Podłącz kabel eDP do złącza na płycie głównej [2]. 7. Umieść klamrę kabla eDP nad złączem eDP [3]. 8. Wkręć śrubę (M2x4) mocującą klamrę kabla eDP do płyty głównej [4]. 9. Przyklej taśmę mocującą klamrę kabla eDP [5].
10. Podłącz kabel czytnika linii papilarnych do złącza na płycie głównej [1]. 11. Załóż klamrę czytnika linii papilarnych [2]. 12. Wkręć śrubę (M2,5x4) mocującą klamrę czytnika linii papilarnych do płyty głównej [3].
13. Podłącz następujące kable: a. kabel USH [1] b. kabel płyty LED [2]. c. kabel touchpada [3].
14. Umieść wspornik modułu pamięci w gnieździe na płycie głównej [1]. 15. Wkręć trzy śruby (M2x3) mocujące wspornik modułu pamięci do płyty głównej [2].
Kolejne kroki 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Zainstaluj kartę sieci WWAN. Zainstaluj kartę sieci WLAN. Zainstaluj złącze zasilania. Zainstaluj moduł pamięci. Zainstaluj wentylator systemowy. Zainstaluj radiator. Zainstaluj głośnik. Zainstaluj baterię. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
Bateria pastylkowa Wymontowywanie baterii pastylkowej Wymagania 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj głośnik. Wymontuj radiator. Wymontuj moduł pamięci. Wymontuj wentylator systemowy. Wymontuj złącze zasilania. Wymontuj kartę sieci WLAN. Wymontuj kartę sieci WWAN. Wymontuj płytę systemową.
Kolejne kroki 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Zainstaluj płytę systemową. Zainstaluj kartę sieci WWAN. Zainstaluj kartę sieci WLAN. Zainstaluj złącze zasilania. Zainstaluj moduł pamięci. Zainstaluj wentylator systemowy. Zainstaluj radiator. Zainstaluj głośnik. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera. Zestaw wyświetlacza Wymontowywanie zestawu wyświetlacza Wymagania 1. 2. 3. 4.
Kroki 1. Odklej taśmę samoprzylepną i odłącz kabel od złącza na płycie systemowej [1]. 2. Wykręć śrubę (M2x4) mocującą wspornik kabla eDP do płyty systemowej [2]. 3. Wyjmij wspornik kabla eDP z płyty systemowej [3]. 4. Odłącz i wyjmij kabel eDP [4]. 5. Rozłóż zestaw wyświetlacza pod kątem 180 stopni i odwróć system, a następnie umieść go na płaskiej powierzchni.
6. Wykręć cztery śruby (M2,5x4) mocujące zestaw wyświetlacza do obudowy systemu [1]. 7. Wyjmij zestaw wyświetlacza z komputera [2].
Instalowanie zestawu wyświetlacza Informacje na temat zadania UWAGA: Przed zainstalowaniem zestawu wyświetlacza na zestawie podpórki na nadgarstek i klawiatury upewnij się, że zawiasy są otwarte pod maksymalnym kątem. Kroki 1. Umieść obudowę systemu pod zawiasami zestawu wyświetlacza [1]. 2. Wkręć cztery śruby (M2,5x4) mocujące zestaw wyświetlacza do obudowy systemu [2].
3. Umieść obudowę systemu na zestawie wyświetlacza.
4. Podłącz kabel do złącza na płycie głównej i przyklej mocującą go taśmę [1]. 5. Poprowadź kabel eDP i podłącz go do złącza eDP [2]. 6. Umieść klamrę kabla eDP na płycie głównej [3]. 7. Wykręć śrubę (M2x4) mocującą klamrę kabla eDP do płyty głównej [4].
Kolejne kroki 1. 2. 3. 4. Zainstaluj baterię. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera. Klawiatura Wymontowywanie klawiatury Wymagania 1. 2. 3. 4. 5. 6. 7. 8. 9. Wykonaj procedurę przedstawioną w sekcji Przed przystąpieniem do serwisowania komputera. Wyjmij kartę microSD. Wymontuj pokrywę dolną. Wymontuj akumulator. Wymontuj głośnik. Wymontuj moduł pamięci. Wymontuj wentylator systemowy. Wymontuj złącze zasilania.
10. Wymontuj kartę sieci WWAN. 11. Wymontuj płytę systemową. UWAGA: Płytę systemową można wyjąć bez demontowania radiatora. 12. Wymontuj baterię pastylkową. Kroki 1. Odklej taśmę mocującą klawiaturę i czytnik kart Smart Card. 2. Otwórz zatrzask i odłącz kabel podświetlenia oraz kabel klawiatury od touchpada.
3. Wykręć 19 śrub (M2x2), które mocują klawiaturę do podpórki na nadgarstek [1]. 4. Wyjmij klawiaturę z komputera [2].
Instalowanie klawiatury Kroki 1. Dopasuj i umieść klawiaturę w podpórce na nadgarstek [1]. 2. Wkręć 19 śrub (M2x2), które mocują klawiaturę do podpórki na nadgarstek [2].
3. Podłącz kabel podświetlenia oraz kabel klawiatury do złączy na touchpadzie.
4. Przyklej taśmę mocującą klawiaturę i płytę czytnika kart Smart Card.
Kolejne kroki 1. Zainstaluj baterię pastylkową. 2. Zainstaluj płytę systemową. UWAGA: Płytę systemową można zainstalować bez demontowania radiatora. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Zainstaluj kartę sieci WWAN. Zainstaluj kartę sieci WLAN. Zainstaluj złącze zasilania. Zainstaluj wentylator systemowy. Zainstaluj moduł pamięci. Zainstaluj głośnik. Zainstaluj akumulator. Zamontuj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę przedstawioną w sekcji Po zakończeniu serwisowania komputera.
2. Wykręć dwie śruby (M2x2,5) mocujące płytę czytnika kart Smart Card do podparcia dłoni [1]. 3. Wyjmij płytę czytnika kart Smart Card z komputera [2].
Instalowanie płyty czytnika kart Smart Card Kroki 1. Dopasuj i umieść płytę czytnika kart Smart Card w podparciu dłoni [1]. 2. Wkręć dwie śruby (M2x2,5) mocujące płytę czytnika kart Smart Card do podparcia dłoni [2].
3. Poprowadź kabel czytnika kart Smart Card.
Kolejne kroki 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Zainstaluj baterię pastylkową. Zainstaluj płytę systemową. Zainstaluj kartę sieci WWAN. Zainstaluj kartę sieci WLAN. Zainstaluj złącze zasilania. Zainstaluj moduł pamięci. Zainstaluj wentylator systemowy. Zainstaluj głośnik. Zainstaluj akumulator. Zainstaluj pokrywę dolną. Zainstaluj kartę microSD. Wykonaj procedurę opisaną w części Po zakończeniu serwisowania komputera.
7. 8. 9. 10. 11. Wymontuj wentylator systemowy. Wymontuj złącze zasilania. Wymontuj kartę sieci WLAN. Wymontuj kartę sieci WWAN. Wymontuj płytę systemową. UWAGA: Płytę systemową można wyjąć bez demontowania radiatora. 12. Wymontuj baterię pastylkową. 13. Wykonaj następujące czynności, aby wymontować płytę czytnika kart Smart Card. Informacje na temat zadania Po wykonaniu powyższych czynności pozostanie zestaw podpórki na nadgarstek i klawiatury. Kolejne kroki 1. Zainstaluj płytę czytnika kart Smart Card.
5 Rozwiązywanie problemów Tematy: • • • Dell SupportAssist — przedrozruchowy test diagnostyczny wydajności systemu Systemowe lampki diagnostyczne Wyłączanie i włączanie karty Wi-Fi Dell SupportAssist — przedrozruchowy test diagnostyczny wydajności systemu Informacje na temat zadania Test diagnostyczny SupportAssist obejmuje całościowe sprawdzenie elementów sprzętowych.
Systemowe lampki diagnostyczne Lampka zasilania i stanu baterii Lampka stanu zasilania i baterii: wskazuje stan zasilania i baterii komputera. Możliwe stany zasilania są następujące: Ciągłe białe światło — zasilacz jest podłączony, a poziom naładowania baterii wynosi powyżej 5%. Bursztynowe światło — komputer jest zasilany z baterii, której poziom naładowania wynosi poniżej 5%. , wyłączone ● Komputer jest podłączony do zasilacza, a bateria jest w pełni naładowana.
UWAGA: Niektórzy dostawcy usług internetowych (ISP) zapewniają urządzenie łączące funkcje routera i modemu. Kroki 1. Wyłącz komputer. 2. Wyłącz modem. 3. Wyłącz router bezprzewodowy. 4. Odczekaj 30 sekund. 5. Włącz router bezprzewodowy. 6. Włącz modem. 7. Włącz komputer.
6 Uzyskiwanie pomocy Tematy: • Kontakt z firmą Dell Kontakt z firmą Dell Wymagania UWAGA: Jeśli nie masz aktywnego połączenia z Internetem, informacje kontaktowe możesz znaleźć na fakturze, w dokumencie dostawy, na rachunku lub w katalogu produktów firmy Dell. Informacje na temat zadania Firma Dell oferuje kilka różnych form obsługi technicznej i serwisu, online oraz telefonicznych. Ich dostępność różni się w zależności od produktu i kraju, a niektóre z nich mogą być niedostępne w regionie użytkownika.