Dell Latitude 5300 서비스 매뉴얼 1 규정 모델: P97G 규정 유형: P97G001 June 2020 개정 A02
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2018-2019 Dell Inc. 또는 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상표일 수 있습니다.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2018-2019 Dell Inc. 또는 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상표일 수 있습니다.
목차 1 컴퓨터에서 작업하기...................................................................................................................... 7 안전 지침................................................................................................................................................................................7 컴퓨터 내부 작업을 시작하기 전에............................................................................................................................. 7 안전 지침..........................................
스피커 분리.................................................................................................................................................................... 41 스피커 설치................................................................................................................................................................... 44 시스템 팬................................................................................................................................................................
디스플레이(eDP) 케이블.................................................................................................................................................109 디스플레이 케이블 제거............................................................................................................................................109 디스플레이 케이블 설치.............................................................................................................................................110 디스플레이 후면 커버 어셈블리....................
1 컴퓨터에서 작업하기 안전 지침 전제조건 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 특별히 언급하지 않는 한 이 문서에 포함된 각 절차 에서는 다음과 같은 조건을 전제하고 있음을 유의하십시오. • • 컴퓨터와 함께 제공된 안전 정보를 읽었습니다. 분리 절차를 역순으로 수행하여 구성요소를 교체하거나 설치(별도로 구입한 경우)할 수 있습니다. 이 작업 정보 노트: 컴퓨터 덮개 및 패널을 열기 전에 전원을 모두 분리합니다. 컴퓨터 내부에서 작업한 후에는 전원을 연결하기 전에 덮개, 패 널 및 나사를 전부 장착합니다. 경고: 컴퓨터 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어보십시오. 추가 안전 모범 사례 정보는 규정 준 수 홈 페이지를 참조하십시오. 주의: 대부분의 수리는 인증받은 서비스 기술자가 수행해야 합니다.
노트: 정전기 방전을 방지하려면 손목 접지대를 사용하거나 주기적으로 컴퓨터 뒷면의 커넥터와 도색되지 않은 금속 표면을 동시에 만져서 접지하십시오. 안전 지침 안전 지침 장에서는 분해 지침을 수행하기 전에 따라야 하는 기본 단계를 자세히 설명합니다. 설치를 진행하거나 분해 또는 재조립 단계를 거치는 고장 수리 절차를 진행하기 전에 다음 안전 지침을 준수하십시오. • • • • • • 시스템 및 장착된 모든 주변 장치를 끕니다. 시스템 및 장착된 모든 주변 장치를 AC 전원에서 분리합니다. 모든 네트워크 케이블, 전화기 및 통신선을 시스템에서 분리합니다. 태블릿노트북 내부에서 작업할 때는 ESD 현장 서비스 키트를 사용하여 정전기 방전(ESD)을 방지해야 합니다. 시스템 구성요소를 분리한 후에는 분리된 구성요소를 정전기 방지 처리된 매트에 조심스럽게 둡니다. 비전도성 고무 밑창이 달린 신발을 신어서 감전 사고를 당할 가능성을 줄입니다.
ESD 현장 서비스 키트 모니터링되지 않는 현장 서비스 키트가 가장 일반적으로 사용되는 서비스 키트입니다. 각 현장 서비스 키트에는 세 가지 기본 구성 요 소인 정전기 방지 매트, 손목 접지대, 본딩 와이어가 포함되어 있습니다. ESD 현장 서비스 키트의 구성 요소 ESD 현장 서비스 키트의 구성 요소는 다음과 같습니다. • • • • • • • 정전기 방지 매트 – 정전기 방지 매트는 소산성이며 서비스 절차 중에 부품을 올려 놓을 수 있습니다. 정전기 방지 매트를 사용할 때 손목 접지대의 착용감이 좋아야 하며, 본딩 와이어가 작동 중인 시스템의 매트와 베어 메탈에 연결되어야 합니다. 적절히 배치 하면 서비스 부품을 ESD 용기에서 분리하여 매트 위에 직접 놓을 수 있습니다. ESD에 민감한 구성 요소는 손 안, ESD 매트 위, 시 스템 내부 또는 용기 안에서 안전합니다.
6. 장비를 내릴 때에는 이 지침의 역순을 따르십시오. 컴퓨터 내부 작업을 마친 후에 이 작업 정보 재장착 절차를 완료한 후 컴퓨터 전원을 켜기 전에 외부 장치, 카드, 케이블 등을 연결했는지 확인합니다. 단계 1. 컴퓨터에 전화선 또는 네트워크 케이블을 연결합니다. 주의: 네트워크 케이블을 연결하려면, 먼저 케이블을 네트워크 장치에 꽂은 다음 컴퓨터에 꽂습니다. 2. 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 3. 컴퓨터를 켭니다. 4. 필요한 경우, ePSA diagnostics(ePSA 진단)를 실행하여 컴퓨터가 올바르게 작동하는지 확인합니다.
2 기술 및 구성 요소 이 장에서는 시스템에서 사용 가능한 기술 및 구성 요소를 자세히 설명합니다. 주제: • • • • USB 기능 USB Type-C HDMI 1.4a 전원 버튼 LED 동작 USB 기능 USB(Universal Serial Bus)라고 불리는 범용 직렬 버스는 1996년에 도입되었습니다. USB는 호스트 컴퓨터와 마우스, 키보드, 외부 드라 이버, 프린터와 같은 주변 기기 간의 연결을 획기적으로 단순화시켰습니다. 아래의 표에서 USB의 진화 과정을 살펴 볼 수 있습니다. 표 1. USB 진화 유형 데이터 전송률 범주 도입 년도 USB 2.0 480Mbps 고속 2000 USB 3.0/USB 3.1 Gen 1 5Gbps 슈퍼 속도 2010 USB 3.1 Gen2 슈퍼 속도 2013 10Gbps USB 3.0/USB 3.1 Gen 1(SuperSpeed USB) 지난 몇 년간 USB 2.
• • 이전의 USB 2.0에는 4개의 와이어(전원, 접지, 차등 데이터용 1쌍)가 있었으나 USB 3.0/USB 3.1 Gen 1 버전에서는 통합 연결이 가 능한 총 8개의 와이어(전원, 접지, 차등 데이터용 3쌍)가 설치되어 있습니다. USB 3.0/USB 3.1 Gen 1은 USB 2.0의 반이중 배열이 아닌 양방향 데이터 인터페이스를 활용합니다. 이론상으로는 대역폭이 10배 늘어납니다. 오늘날 고화질 비디오 콘텐츠의 데이터 전송, 테라바이트 스토리지 장치, 고등급 메가픽셀 디지털 카메라 등에 대한 기대가 점점 높아 짐에 따라, USB 2.0의 속도는 충분하지 않을 수 있습니다. 게다가 USB 2.0을 연결할 경우 실제 최대 데이터 전송 속도는 320Mbps(40MB/s)로, 이론상 최대 처리량인 480Mbps에 결코 근접할 수 없습니다. 마찬가지로 USB 3.0/USB 3.1 Gen 1 연결 역시 4.8Gbps에 도달할 수 없습니다.
USB Type-C USB Type-C는 새로운 소형 물리적 커넥터입니다. 커넥터 자체에 USB 3.1 및 USB PD(USB Power Delivery)와 같은 다양한 신규 USB 표준 지원 기능이 있습니다. 대체 모드 USB Type-C는 새로운 초소형 커넥터 표준으로, 이전 USB Type-A 플러그의 약 1/3 크기입니다. 이는 모든 디바이스에서 사용할 수 있 는 단일 커넥터 표준입니다. USB Type-C 포트는 "대체 모드"를 사용하여 다양한 프로토콜을 지원할 수 있으므로 이를 통해 해당 단일 USB 포트에서 HDMI, VGA, DisplayPort 또는 다른 유형의 연결 출력이 가능한 어댑터를 확보할 수 있습니다. USB Power Delivery USB PD 사양은 USB Type-C와도 밀접히 연결되어 있습니다. 현재 스마트폰, 태블릿 및 기타 모바일 디바이스는 대체로 USB 연결을 사용하여 충전합니다. USB 2.0 연결은 최대 2.
USB Type-C 사용 Thunderbolt 3 Thunderbolt 3은 최대 속도 40Gbps를 자랑하는 USB Type-C를 지원하여, 모든 일을 처리할 수 있는 하나의 컴팩트한 포트로 Thunderbolt를 향상시켰습니다. 이를 통해 모든 도킹, 디스플레이 또는 외장 하드 드라이브 같은 데이터 장치와 가장 빠르고 다양한 방법의 연결을 제공합니다. Thunderbolt 3은 USB Type-C 커넥터/포트를 사용하여 지원되는 주변 장치와 연결됩니다. 1. 2. 3. 4. Thunderbolt 3은 USB Type-C 커넥터와 케이블을 사용하므로 휴대성이 좋고 방향 전환이 가능합니다. Thunderbolt 3은 최대 40Gbps 속도를 제공합니다. DisplayPort 1.2 - 기존 DisplayPort 모니터, 장치 및 케이블과 호환 USB Power Delivery - 지원되는 컴퓨터에서 최대 130W USB Type-C 사용 Thunderbolt 3의 주요 기능 1. 2. 3. 4. 5.
HDMI 이점 • • • • • 품질 HDMI는 선명한 화질을 위해 비압축된 디지털 오디오 및 비디오를 전송합니다. 저비용 HDMI는 단순하고 비용 효율적인 방식으로 비압축된 비디오 형식을 지원하는 동시에 디지털 인터페이스의 품질과 기능을 제공합니다. 오디오 HDMI는 표준 스테레오부터 멀티채널 서라운드 사운드까지, 다양한 오디오 형식을 지원합니다. HDMI는 비디오와 멀티채널 오디오를 하나의 케이블로 통합하여 현재 A/V 시스템에서 사용되는 많은 케이블로 인해 발생하는 비 용과 복잡성을 감소시킵니다. HDMI의 새 기능은 DVD 플레이어와 같은 비디오 소스와 DTV 간의 통신을 지원합니다. 전원 버튼 LED 동작 특정 Dell Latitude 시스템에서 전원 버튼 LED는 시스템 상태를 표시하는 데 사용되며, 이에 따라 누를 경우 전원 버튼에 불이 켜집니 다.
지문 판독기가 탑재된 전원 버튼은 LED가 없으며 시스템 안에서 사용할 수 있는 LED를 활용하여 시스템 상태를 표시합니다. • 전원 어댑터 LED: • ○ 콘센트에서 전원이 공급되면 전원 어댑터 커넥터의 LED가 흰색으로 켜집니다. 배터리 상태 LED: ○ 컴퓨터가 전원 콘센트에 연결되어 있는 경우, 배터리 표시등은 다음과 같이 동작합니다. 1. 흰색으로 고정 - 배터리를 충전하는 중입니다. 충전이 완료되면 LED가 꺼집니다. ○ 컴퓨터가 배터리로 작동하는 중에는 배터리 표시등이 다음과 같이 동작합니다. • 1. 꺼짐 - 배터리가 충분하게 충전되었습니다(또는 컴퓨터가 꺼진 상태입니다). 2. 주황색으로 고정 - 배터리 잔량이 매우 부족합니다. 배터리 부족 상태는 남은 배터리 지속 시간이 대략 30분 이하임을 나타 냅니다. 카메라 LED • ○ 카메라가 켜지면 흰색 LED가 활성화됩니다.
3 주요 시스템 구성 요소 1. 베이스 커버 3. 방열판 2. DC 입력 포트 4.
5. 7. 9. 11. 13. 15. 17. 시스템 보드 배터리 스마트 카드 판독기 보드 디스플레이 어셈블리 LED 보드 WLAN 카드 시스템 팬 6. 8. 10. 12. 14. 16. 18. 솔리드 스테이트 드라이브 스피커 손목 받침대 어셈블리 터치패드 버튼 보드 코인 셀 배터리 WWAN 카드 노트: Dell은 구매한 원래 시스템 구성의 구성 요소 및 부품 번호 목록을 제공합니다. 이러한 부품은 고객이 구매한 보증 기간에 따라 사용할 수 있습니다. 구매 옵션은 Dell 영업 담당자에게 문의하십시오.
4 분해 및 재조립 microSD 카드 microSD 카드 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 단계 1. MicroSD 카드를 눌러 컴퓨터에서 분리합니다[1]. 2. MicroSD 카드를 밀어 컴퓨터에서 꺼냅니다[2]. microSD 카드 설치 단계 1. microSD 카드를 컴퓨터의 해당 슬롯에 맞춥니다[1]. 2. 딸깍 소리를 내며 제자리에 끼워질 때까지 microSD 카드를 슬롯에 밀어 넣습니다[2].
3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. SIM 카드 트레이 SIM 카드 트레이 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 단계 1. 핀을 SIM 카드 트레이의 구멍에 삽입하고 트레이가 분리될 때까지 안쪽으로 밉니다[1, 2]. 2. SIM 카드 트레이를 밀어 컴퓨터에서 꺼냅니다[3].
SIM 카드 트레이 설치 단계 1. 금색 접촉면이 위를 향하도록 SIM 카드를 SIM 카드 트레이에 놓습니다[1]. 2. SIM 카드 트레이를 컴퓨터의 슬롯에 맞추고 조심스럽게 밀어 넣습니다[2]. 3. 딸깍 소리를 내며 제자리에 끼워질 때까지 SIM 카드 트레이를 해당 슬롯에 밀어 넣습니다[3].
4. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 베이스 덮개 베이스 덮개 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 단계 1. 8개의 조임 나사를 풉니다[1].
2. 플라스틱 스크라이브를 사용하여[1] 베이스 커버를 왼쪽 상단에서 들어 올리고 계속해서 베이스 커버의 측면을 엽니다[2].
3. 베이스 커버를 들어 올려 컴퓨터에서 분리합니다. 베이스 덮개 설치 단계 1. 베이스 커버를 컴퓨터에 맞추어 놓습니다.
2. 딸깍 소리를 내며 제자리에 고정될 때까지 베이스 커버의 가장자리와 측면을 누릅니다.
3. 8개의 조임 나사를 조여 베이스 커버를 컴퓨터에 고정합니다.
다음 단계 1. MicroSD 카드를 장착합니다. 2. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 배터리 리튬 이온 배터리 예방 조치 주의: • 리튬 이온 배터리를 다룰 때는 주의하십시오. • 배터리를 시스템에서 제거하기 전에 최대한 방전합니다. 배터리를 방전하려면 AC 어댑터를 시스템에서 연결 해제하여 배터 리가 방전되도록 만들면 됩니다. • 배터리를 찌그러뜨리거나 떨어뜨리거나 훼손하거나 외부 개체로 배터리에 구멍을 뚫지 마십시오. • 고온에 배터리를 노출하거나 배터리 팩과 셀을 분해하지 마십시오. • 배터리 표면에 압력을 가하지 마십시오. • 배터리를 구부리지 마십시오. • 툴을 사용해 배터리를 꺼내려 하거나 배터리에 힘을 가하지 마십시오. • 우발적인 펑처 또는 배터리 및 기타 시스템 구성 요소에 대한 손상을 방지하기 위해 이 제품을 수리하는 동안 나사가 손실되 지 않도록 하십시오.
3. 배터리를 손목 받침대에 고정하는 2개의 조임 나사를 풉니다[1]. 4. 배터리를 안쪽으로 밀고 손목 받침대에서 들어 올립니다[2].
배터리 설치 단계 1. 배터리를 손목 받침대에 맞추어 밉니다[1]. 2. 2개의 조임 나사를 조여 배터리를 손목 받침대에 고정합니다[2].
3. 배터리 케이블을 시스템 보드의 커넥터에 연결합니다[1]. 4. 접착 테이프를 부착하여 배터리 케이블 커넥터를 고정합니다[2].
다음 단계 1. 베이스 덮개를 장착합니다. 2. MicroSD 카드를 장착합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. WWAN 카드 WWAN 카드 분리 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 2. 3. 4. WWAN 카드 브래킷을 시스템 보드에 고정하는 1개의 M2x3 나사를 제거합니다[1]. WWAN 안테나 케이블을 고정하는 WWAN 카드 브래킷을 제거합니다[2]. WWAN 안테나 케이블을 WWAN 카드의 커넥터에서 연결 해제합니다[3]. WWAN 카드를 밀어서 시스템 보드의 커넥터에서 들어 올립니다[4].
WWAN 카드 장착 이 작업 정보 주의: WWAN 카드의 손상을 방지하려면 카드 아래에 케이블을 두지 마십시오. 단계 1. 2. 3. 4. 32 WWAN 카드를 시스템 보드의 커넥터에 삽입합니다[1]. WWAN 안테나 케이블을 WWAN 카드의 커넥터에 연결합니다[2]. WWAN 카드 브래킷을 놓아 WWAN 안테나 케이블을 WWAN 카드에 고정합니다[3]. 1개의 M2x3 나사를 장착하여 WWAN 카드 브래킷을 WWAN 카드에 고정합니다[4].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. WLAN 카드 WLAN 카드 제거 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 2. 3. 4. WLAN 카드 브래킷을 시스템 보드에 고정하는 1개의 M2x2 나사를 제거합니다[1]. WLAN 안테나 케이블을 고정하는 WLAN 카드 브래킷을 제거합니다[2]. WLAN 안테나 케이블을 WLAN 카드의 커넥터에서 연결 해제합니다[3]. WLAN 카드를 밀어서 시스템 보드의 커넥터에서 들어 올립니다[4].
WLAN 카드 장착 이 작업 정보 주의: WLAN 카드의 손상을 방지하려면 카드 아래에 케이블을 두지 마십시오. 단계 1. 2. 3. 4. 34 WLAN 카드를 시스템 보드의 커넥터에 삽입합니다[1]. WLAN 안테나 케이블을 WLAN 카드의 커넥터에 연결합니다[2]. WLAN 카드 브래킷을 놓아 WLAN 안테나 케이블을 WLAN 카드에 고정합니다[3]. 1개의 M2x3 나사를 장착하여 WLAN 카드 브래킷을 WLAN 카드에 고정합니다[4].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 메모리 모듈 메모리 모듈 분리 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 메모리 모듈이 튀어나올 때까지 메모리 모듈을 고정하는 보존 클립을 들어 올립니다[1]. 2. 메모리 모듈을 메모리 모듈 슬롯에서 제거합니다[2].
메모리 모듈 설치 단계 1. 메모리 모듈의 노치를 메모리 모듈 슬롯의 탭에 맞춥니다. 2. 메모리 모듈을 일정한 각도로 슬롯에 단단히 밀어 넣습니다[1]. 3. 클립에 의해 고정될 때까지 메모리 모듈을 아래로 누릅니다[2]. 노트: 소리가 나지 않으면 메모리 모듈을 분리했다가 다시 설치합니다.
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. SSD M.2 SSD 제거 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. M.2 SSD 지지 브래킷을 손목 받침대에 고정하는 2개의 M2x3 나사를 제거합니다[1]. 2. SSD 지지 브래킷을 살짝 돌려서 M.2 SSD 슬롯에서 제거합니다[2].
3. M.2 SSD를 손목 받침대에 고정하는 1개의 M2x2 나사를 제거합니다[1]. 4. M.2 SSD를 들어 올려 컴퓨터에서 분리합니다[2].
M.2 SSD 설치 단계 1. M.2 SSD를 손목 받침대의 슬롯에 놓습니다[1]. 2. 1개의 M2x2 나사를 장착하여 M.2 SSD를 손목 받침대에 고정합니다[2].
3. SSD 지지 브래킷을 M.2 SSD 위에 맞추어 놓습니다[1]. 4. 2개의 M2x3 나사를 장착하여 SSD 지지 브래킷을 손목 받침대에 고정합니다[2].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 스피커 스피커 분리 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 스피커 케이블을 시스템 보드의 커넥터에서 연결 해제합니다[1]. 2. 스피커 케이블을 손목 받침대에 고정하는 접착 테이프를 떼어냅니다[2].
3. 터치패드 케이블을 도터보드의 커넥터에서 연결 해제합니다. 4. 접착 테이프를 떼어내고 스피커 케이블을 라우팅 해제합니다.
5. 스피커를 들어 올려 손목 받침대에서 제거합니다.
스피커 설치 단계 1. 정렬 포스트 및 고무 그로밋을 사용하여 스피커를 손목 받침대의 슬롯에 놓습니다. 2. 스피커 케이블을 라우팅 가이드에 통과시켜 배선합니다.
3. 접착 테이프를 부착하여 스피커 케이블을 손목 받침대에 고정합니다[1]. 4. 스피커 케이블을 시스템 보드의 커넥터에 연결합니다[2].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 시스템 팬 시스템 팬 분리 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 시스템 팬 케이블을 시스템 보드의 커넥터에서 연결 해제합니다.
2. 시스템 팬을 손목 받침대에 고정하는 2개의 M2x5 나사를 제거합니다[1]. 3. 시스템 팬을 들어 올려 컴퓨터에서 분리합니다[2].
시스템 팬 설치 단계 1. 시스템 팬의 나사 구멍을 손목 받침대의 나사 구멍에 맞추어 놓습니다[1]. 2. 2개의 M2x5 나사를 장착하여 시스템 팬을 손목 받침대에 고정합니다[2].
3. 시스템 보드의 커넥터에 시스템 팬 케이블을 연결합니다.
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 방열판 방열판 제거 - UMA 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 단계 1. 방열판을 시스템 보드에 고정하는 4개의 조임 나사를 풉니다[1]. 노트: 방열판에 표시된 설명선 번호[1, 2, 3, 4] 순서로 나사를 풉니다. 2. 방열판을 들어올려 시스템 보드에서 분리합니다[2].
방열판 설치 - UMA 단계 1. 방열판을 시스템 보드에 놓고 방열판의 나사 구멍을 시스템 보드의 나사 구멍에 맞춥니다[1]. 2. 방열판을 시스템 보드에 고정하는 4개의 조임 나사를 방열판에 표시된 순서대로 조입니다[2]. 다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. DC 입력 포트 DC 입력 포트 분리 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다.
단계 1. Type-C 브래킷을 시스템 보드에 고정하는 2개의 M2x4 나사를 제거합니다[1]. 2. Type-C 브래킷을 들어 올려 컴퓨터에서 분리합니다[2]. 3. DC 입력 포트 케이블을 시스템 보드의 커넥터에서 연결 해제하고 DC 입력 포트를 컴퓨터에서 제거합니다[1, 2].
DC 입력 포트 설치 단계 1. DC 입력 포트를 컴퓨터의 해당 슬롯에 놓습니다[1]. 2. DC 입력 포트 케이블을 시스템 보드의 커넥터에 연결합니다[2].
3. Type-C 브래킷을 컴퓨터의 해당 슬롯에 놓습니다[1]. 4. Type-C 브래킷을 손목 받침대에 고정하는 2개의 M2x4 나사를 장착합니다[2].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. LED 보드 LED 보드 분리 전제조건 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 단계 1. LED 보드 케이블을 시스템 보드의 커넥터에서 연결 해제합니다[1]. 2. LED 보드 케이블을 라우팅 해제합니다[2].
3. LED 보드 케이블 커넥터를 LED 보드에 고정하는 접착 테이프를 떼어냅니다[1]. 4. LED 보드를 고정하는 회색 접착 테이프를 떼어냅니다[2].
5. LED 보드를 손목 받침대에 고정하는 1개의 M2x2.5 나사를 제거합니다[1]. 6. LED 보드를 들어 올려 컴퓨터에서 분리합니다[2].
LED 보드 설치 단계 1. LED 보드를 놓고 LED 보드의 나사 구멍을 손목 받침대의 나사 구멍에 맞춥니다[1]. 2. 1개의 M2x2.5 나사를 장착하여 LED 보드를 손목 받침대에 고정합니다[2].
3. 회색 접착 테이프를 부착하여 LED 보드를 고정합니다[1]. 4. 접착 테이프를 부착하여 LED 보드를 고정합니다[2].
5. LED 보드 케이블을 시스템 보드의 커넥터에 연결하고 LED 보드 케이블을 라우팅합니다[1, 2].
다음 단계 1. 2. 3. 4. 5. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 터치패드 버튼 보드 터치패드 버튼 보드 제거 전제조건 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 단계 1. 래치를 열고 터치패드 버튼 보드 케이블을 터치패드 보드의 커넥터에서 연결 해제합니다. 2. 터치패드 버튼 브래킷을 손목 받침대에 고정하는 2개의 M2x3 나사를 제거합니다[1]. 3. 터치패드 버튼 보드 브래킷을 들어 올려 컴퓨터에서 분리합니다[2].
터치패드 버튼 보드 설치 단계 1. 터치패드 버튼 보드를 손목 받침대의 슬롯에 놓습니다[1]. 2. 2개의 M2x3 나사를 장착하여 터치패드 버튼 보드를 손목 받침대에 고정합니다[2].
3. 터치패드 버튼 보드 케이블을 터치패드 보드의 커넥터에 연결합니다.
다음 단계 1. 2. 3. 4. 5. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 시스템 보드 시스템 보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 방열판을 제거합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다. WWAN 카드를 제거합니다. 단계 1. 래치를 들어 올려 다음 케이블을 연결 해제합니다. a. USH 케이블[1]. b. LED 보드 케이블[2]. c. 터치패드 케이블[3].
2. 지문 지지 브래킷을 시스템 보드에 고정하는 1개의 M2.5x4 나사를 제거합니다[1]. 3. 지문 지지 브래킷을 들어 올려 컴퓨터에서 분리합니다[2]. 4. 지문 포트를 연결 해제합니다[3].
5. 6. 7. 8. 66 접착 테이프를 떼어내고 케이블을 시스템 보드의 커넥터에서 연결 해제합니다[1]. eDP 브래킷을 시스템 보드에 고정하는 1개의 M2x4 나사를 제거합니다[2]. eDP 브래킷을 컴퓨터에서 제거합니다[3]. 래치를 들어 올리고 eDP 케이블을 시스템 보드의 커넥터에서 연결 해제합니다[4].
9. 손목 받침대에서 코인 셀 배터리를 분리합니다.
10. 시스템 보드를 손목 받침대에 고정하는 3개의 M2x2 나사와 1개의 M2.5x4 나사를 제거합니다[1]. 11. 시스템 보드를 들어 올려 컴퓨터에서 분리합니다[2].
시스템 보드 설치 단계 1. 시스템 보드를 손목 받침대에 맞추어 놓습니다[1]. 2. 3개의 M2x2 나사와 1개의 M2.5x4 나사를 장착하여 시스템 보드를 손목 받침대에 고정합니다[2].
3. 코인 셀 배터리를 손목 받침대의 해당 슬롯에 놓습니다.
4. 5. 6. 7. 케이블을 시스템 보드의 커넥터에 연결하고 접착 테이프를 부착합니다[1]. eDP 케이블을 시스템 보드의 커넥터에 연결합니다[2]. eDP 지지 브래킷을 eDP 커넥터 위에 놓습니다[3]. 1개의 M2x4 나사를 장착하여 eDP 브래킷을 시스템 보드에 고정합니다[4].
8. 지문 케이블을 시스템 보드의 커넥터에 연결합니다[1]. 9. 지문 지지 브래킷을 놓습니다[2]. 10. 1개의 M2.5x4 나사를 장착하여 지문 지지 브래킷을 시스템 보드에 고정합니다[3].
11. 다음 케이블을 연결합니다. a. USH 케이블[1]. b. LED 보드 케이블[2]. c. 터치패드 케이블[3].
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 메모리 모듈을 장착합니다. 시스템 팬을 장착합니다. 방열판을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 코인 셀 배터리 코인 셀 배터리 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 방열판을 제거합니다. 메모리 모듈을 분리합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다. WWAN 카드를 제거합니다. 시스템 보드를 분리합니다. 단계 시스템 보드를 뒤집고 코인 셀 배터리 케이블을 시스템 보드의 커넥터에서 연결 해제합니다. 코인 셀 배터리 설치 단계 시스템 보드를 뒤집고 코인 셀 배터리 케이블을 시스템 보드의 커넥터에 연결합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 시스템 보드를 장착합니다. WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 메모리 모듈을 장착합니다. 시스템 팬을 장착합니다. 방열판을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 어셈블리 디스플레이 조립품 분리 전제조건 1. 2. 3. 4. 76 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다.
단계 1. 2. 3. 4. 접착 테이프를 떼어내고 케이블을 시스템 보드의 커넥터에서 연결 해제합니다[1]. eDP 케이블 브래킷을 시스템 보드에 고정하는 1개의 M2x4 나사를 제거합니다[2]. eDP 케이블 브래킷을 시스템 보드에서 들어 올립니다[3]. eDP 케이블을 연결 및 라우팅 해제합니다[4]. 5. 디스플레이 어셈블리를 180도로 열고 시스템을 뒤집은 다음 시스템을 평평한 표면에 놓습니다.
6. 디스플레이 어셈블리를 시스템 섀시에 고정하는 4개의 M2.5x3 나사를 제거합니다[1]. 7. 디스플레이 어셈블리를 시스템에서 제거합니다[2].
디스플레이 조립품 설치 이 작업 정보 노트: 디스플레이 어셈블리를 손목 받침대 및 키보드 어셈블리에 장착하기 전에 힌지가 최대한 열려 있는지 확인하십시오. 단계 1. 시스템 섀시를 디스플레이 어셈블리의 힌지 아래에 맞추어 놓습니다[1]. 2. 디스플레이 어셈블리를 시스템 섀시에 고정하는 4개의 M2.5x3 나사를 장착합니다[2].
3. 시스템 섀시를 디스플레이 어셈블리에 장착합니다.
4. 5. 6. 7. 케이블을 시스템 보드의 커넥터에 연결하고 접착 테이프를 부착합니다[1]. eDP 케이블을 다시 라우팅라고 eDP 커넥터에 연결합니다[2]. eDP 케이블 브래킷을 시스템 보드에 놓습니다[3]. eDP 케이블 브래킷을 시스템 보드에 고정하는 1개의 M2x4 나사를 장착합니다[4].
다음 단계 1. 2. 3. 4. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 키보드 키보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 82 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 메모리 모듈을 분리합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다.
10. WWAN 카드를 제거합니다. 11. 시스템 보드를 분리합니다. 노트: 시스템 보드는 방열판이 부착된 상태로 제거할 수 있습니다. 12. 코인 셀 배터리를 제거합니다. 단계 1. 키보드와 스마트 카드 판독기를 고정하는 접착 테이프를 떼어냅니다. 2. 래치를 들어 올리고 백라이트 케이블과 키보드 케이블을 터치패드의 커넥터에서 연결 해제합니다.
3. 키보드를 손목 받침대에 고정하는 19개의 M2x2 나사를 제거합니다[1]. 4. 컴퓨터에서 키보드를 제거합니다[2].
키보드 설치 단계 1. 키보드를 손목 받침대에 맞추어 놓습니다[1]. 2. 키보드를 손목 받침대에 고정하는 19개의 M2x2 나사를 장착합니다[2].
3. 백라이트 케이블과 키보드 케이블을 터치패드의 커넥터에 연결합니다.
4. 키보드와 스마트 카드 보드를 고정하는 접착 테이프를 부착합니다.
다음 단계 1. 코인 셀 배터리를 장착합니다. 2. 시스템 보드를 장착합니다. 노트: 시스템 보드는 방열판이 부착된 상태로 장착할 수 있습니다. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 시스템 팬을 장착합니다. 메모리 모듈을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 키보드 브래킷 키보드 브래킷 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 메모리 모듈을 분리합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다. WWAN 카드를 제거합니다.
키보드 브래킷 설치 단계 1. 키보드를 키보드 브래킷에 맞추어 놓습니다[1]. 2. 4개의 M2x2 나사를 장착하여 키보드를 키보드 브래킷에 고정합니다[2].
다음 단계 1. 키보드를 장착합니다. 2. 코인 셀 배터리를 장착합니다. 3. 시스템 보드를 장착합니다. 노트: 시스템 보드는 방열판이 부착된 상태로 장착할 수 있습니다. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 90 WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 메모리 모듈을 장착합니다. 시스템 팬을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
스마트 카드 판독기 보드 스마트 카드 판독기 보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 메모리 모듈을 분리합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다. WWAN 카드를 제거합니다. 시스템 보드를 분리합니다. 코인 셀 배터리를 제거합니다. 키보드를 분리합니다. 단계 1. 스마트 카드 판독기 보드 케이블을 라우팅 해제합니다. 2. 스마트 카드 판독기를 손목 받침대에 고정하는 2개의 M2x2.5 나사를 제거합니다[1]. 3. 스마트 카드 판독기 보드를 들어 올려 컴퓨터에서 분리합니다[2].
스마트 카드 판독기 보드 설치 단계 1. 스마트 카드 판독기 보드를 손목 받침대에 맞추어 놓습니다[1]. 2. 스마트 카드 판독기 보드를 손목 받침대에 고정하는 2개의 M2x2.5 나사를 장착합니다[2].
3. 스마트 카드 판독기 케이블을 다시 라우팅합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 키보드를 장착합니다. 코인 셀 배터리를 장착합니다. 시스템 보드를 장착합니다. WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 메모리 모듈을 장착합니다. 시스템 팬을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 커버를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 베젤 디스플레이 베젤 제거 전제조건 1. 2. 3. 4. 5. 94 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다.
단계 1. 노트: 디스플레이 베젤은 제거한 후 재사용할 수 없습니다. 플라스틱 스크라이브를 사용하여 디스플레이 베젤 하단 가장자리 왼쪽 및 오른쪽 힌지 주변의 리세스를 조심스럽게 들어 올려 엽 니다[1]. 2. 디스플레이 베젤의 안쪽 가장자리를 조심스럽게 들어 올려 연 다음 디스플레이 베젤 왼쪽 및 오른쪽의 안쪽 가장자리를 들어 올 려 엽니다[2]. 3. 디스플레이 베젤을 디스플레이 어셈블리에서 들어 올립니다.
디스플레이 베젤 설치 단계 디스플레이 베젤을 디스플레이 어셈블리에 맞춘 다음 조심스럽게 디스플레이 베젤을 제자리에 끼워 넣습니다.
분해 및 재조립 97
다음 단계 1. 2. 3. 4. 5. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 힌지 캡 힌지 캡 제거 전제조건 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 단계 1. 힌지 캡을 섀시에 고정하는 2개의 M2x3 나사를 제거합니다[1]. 2. 힌지 캡을 꼭 집어서 디스플레이 후면 커버의 리브에서 분리한 다음 안쪽으로 밀어서 힌지 캡을 디스플레이 힌지에서 제거합니다 [2].
힌지 캡 설치 단계 1. 힌지 캡을 놓고 디스플레이 힌지에서 바깥쪽으로 밉니다[1]. 2. 힌지 캡을 디스플레이 힌지에 고정하는 2개의 M2x3 나사를 장착합니다.
다음 단계 1. 2. 3. 4. 5. 6. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 힌지 디스플레이 힌지 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 횐지 캡을 제거합니다.
단계 1. 디스플레이 힌지를 디스플레이 어셈블리에 고정하는 4개의 M2.5x3 나사를 제거합니다[1]. 2. 디스플레이 힌지를 디스플레이 후면 커버에서 제거합니다[2]. 디스플레이 힌지 설치 단계 1. 디스플레이 힌지를 디스플레이 어셈블리에 놓습니다. 2. 디스플레이 힌지를 디스플레이 어셈블리에 고정하는 4개의 M2.5x3 나사를 장착합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 횐지 캡을 장착합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 패널 디스플레이 패널 분리 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 3. 베이스 덮개를 분리합니다.
4. 5. 6. 7. 8. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 횐지 캡을 제거합니다. 디스플레이 힌지를 분리합니다. 단계 1. 디스플레이 패널을 디스플레이 어셈블리에 고정하는 2개의 M2x2 나사를 제거하고[1] 디스플레이 패널을 들어 올린 후 뒤집어 디 스플레이 케이블에 액세스합니다[2]. 2. 디스플레이 케이블 커넥터에서 전도성 테이프를 떼어냅니다[1]. 3. 래치를 들어 올리고 디스플레이 케이블을 디스플레이 패널의 커넥터에서 연결 해제합니다[2, 3]. 노트: 디스플레이 패널에서 SR(Stretch Release) 테이프를 당기지 말고 분리합니다. 디스플레이 패널에서 브래킷을 분리할 필요가 없습니다.
분해 및 재조립
디스플레이 패널 설치 단계 1. 디스플레이 케이블을 커넥터에 연결하고 래치를 닫습니다[1, 2]. 2. 전도성 테이프를 부착하여 디스플레이 케이블 커넥터를 고정합니다[3]. 3. 디스플레이 패널을 디스플레이 어셈블리에 고정하는 2개의 M2x2 나사를 장착합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 디스플레이 힌지를 장착합니다. 횐지 캡을 장착합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 카메라 카메라 분리 전제조건 1. 2. 3. 4. 5. 6. 7. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 횐지 캡을 제거합니다.
8. 디스플레이 힌지를 분리합니다. 9. 디스플레이 패널을 분리합니다. 단계 카메라 케이블을 카메라 모듈의 커넥터에서 연결 해제합니다. 카메라 설치 단계 1. 카메라를 디스플레이 후면 커버의 슬롯에 삽입합니다.
2. 카메라 케이블을 커넥터에 연결하고 카메라 커넥터 위에 접착 테이프를 부착합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 디스플레이 패널을 장착합니다. 디스플레이 힌지를 장착합니다. 횐지 캡을 장착합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이(eDP) 케이블 디스플레이 케이블 제거 전제조건 1. 2. 3. 4. 5. 6. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다.
7. 8. 9. 10. 횐지 캡을 제거합니다. 디스플레이 힌지를 분리합니다. 디스플레이 패널을 분리합니다. 카메라를 분리합니다. 단계 전도성 테이프를 떼어내고 디스플레이 케이블을 라우팅 해제하여 접착면에서 분리하고 디스플레이 후면 커버에서 디스플레이 케이 블을 들어 올립니다. 디스플레이 케이블 설치 단계 1. 디스플레이 케이블을 디스플레이 후면 커버에 부착합니다. 2. 전도성 테이프를 부착하고 디스플레이 케이블을 디스플레이 후면 커버에 라우팅합니다.
다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 카메라를 장착합니다. 디스플레이 패널을 장착합니다. 디스플레이 힌지를 장착합니다. 횐지 캡을 장착합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 후면 커버 어셈블리 디스플레이 후면 커버 교체 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 디스플레이 어셈블리를 분리합니다. 디스플레이 베젤을 분리합니다. 횐지 캡을 제거합니다. 디스플레이 힌지를 분리합니다. 디스플레이 패널을 분리합니다.
10. 카메라를 분리합니다. 11. 디스플레이 케이블을 분리합니다. 이 작업 정보 앞 단계를 모두 수행하고 나면 디스플레이 후면 커버가 남습니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 디스플레이 케이블을 장착합니다. 카메라를 장착합니다. 디스플레이 패널을 장착합니다. 디스플레이 힌지를 장착합니다. 횐지 캡을 장착합니다. 디스플레이 베젤을 장착합니다. 디스플레이 어셈블리를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 손목 받침대 어셈블리 손목 받침대 및 키보드 어셈블리 교체 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다.
3. 4. 5. 6. 7. 8. 9. 10. 11. 베이스 덮개를 분리합니다. 배터리를 분리합니다. 스피커를 분리합니다. 메모리 모듈을 분리합니다. 시스템 팬을 제거합니다. DC 입력을 제거합니다. WLAN 카드를 제거합니다. WWAN 카드를 제거합니다. 시스템 보드를 분리합니다. 노트: 시스템 보드는 방열판이 부착된 상태로 제거할 수 있습니다. 12. 코인 셀 배터리를 제거합니다. 13. 키보드를 분리합니다. 14. 스마트 카드 판독기 보드를 제거합니다. 이 작업 정보 앞 단계를 모두 수행하고 나면 손목 받침대와 키보드 어셈블리가 남습니다. 다음 단계 1. 2. 3. 4. 스마트 카드 판독기 보드를 장착합니다. 키보드를 장착합니다. 코인 셀 배터리를 장착합니다. 시스템 보드를 장착합니다. 노트: 시스템 보드는 방열판이 부착된 상태로 장착할 수 있습니다. 5. 6. 7. 8. WWAN 카드를 장착합니다. WLAN 카드를 장착합니다. DC 입력을 장착합니다. 메모리 모듈을 장착합니다.
9. 10. 11. 12. 13. 14. 114 시스템 팬을 장착합니다. 스피커를 장착합니다. 배터리를 장착합니다. 베이스 덮개를 장착합니다. MicroSD 카드를 장착합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
5 문제 해결 강화된 사전 부팅 시스템 평가(ePSA) 진단 이 작업 정보 ePSA 진단(시스템 진단이라고도 함) 프로그램은 하드웨어에 대해 완전한 검사를 수행합니다. ePSA는 BIOS에 내장되어 있으며 BIOS 에 의해 내부적으로 실행됩니다. 내장형 시스템 진단 프로그램은 특정 장치 그룹 또는 장치에 대해 일련의 옵션을 제공하여 사용자가 다음을 수행할 수 있게 합니다. • • • • • • 자동으로 테스트 또는 상호 작용 모드를 실행합니다. 테스트를 반복합니다. 테스트 결과를 표시 또는 저장합니다. 오류가 발생한 장치에 대한 추가 정보를 제공하기 위해 추가 테스트 옵션으로 세부 검사를 실행합니다. 테스트가 성공적으로 완료되었음을 알리는 상태 메시지를 봅니다. 테스트 중 발생하는 문제를 알리는 오류 메시지를 봅니다. 노트: 특정 장치를 위한 일부 테스트는 사용자 상호 작용을 요구합니다. 진단 테스트를 수행할 때는 항상 컴퓨터 터미널 앞을 지 켜야 합니다. ePSA 진단 실행 단계 1. 2. 3.
다음 표는 전원 및 배터리 상태 표시등 패턴과 관련한 문제를 설명합니다. 표 3. LED 코드 진단 표시등 코드 문제 설명 2,1 프로세서 오류 2,2 시스템 보드: BIOS 또는 ROM(읽기 전용 메모리) 장애 2,3 메모리 또는 RAM(Random-Access Memory)이 감지되지 않음 2,4 메모리 또는 RAM(Random-Access Memory) 장애 2,5 잘못된 메모리 설치 2,6 시스템 보드 또는 칩셋 오류 2,7 디스플레이 오류 2,8 LCD 전원 레일 오류 시스템 보드 교체 3,1 코인 셀 배터리 장애 3,2 PCI/비디오 카드/칩 장애 3,3 복구 이미지를 찾을 수 없음 3,4 복구 이미지를 찾았지만 유효하지 않음 3,5 전원 레일 장애 3,6 시스템 BIOS 플래시 불완전 3,7 ME(Management Engine) 오류 카메라 상태 표시등: 카메라가 사용 중인지 여부를 나타냅니다.
6 도움말 보기 주제: • Dell에 문의하기 Dell에 문의하기 전제조건 노트: 인터넷에 연결되어 있지 않은 경우 구매 송장, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. 이 작업 정보 Dell은 다양한 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 단계 1. 2. 3. 4. Dell.com/support로 이동합니다. 지원 카테고리를 선택합니다. 페이지 맨 아래에 있는 국가/지역 선택 드롭다운 메뉴에서 국가 또는 지역을 확인합니다. 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다.