Dell Latitude 5300 Servisni priručnik 1 Model sa regulacijom: P97G Tip sa regulacijom: P97G001 June 2020 Pregl.
Napomene, mere opreza i upozorenja NAPOMENA: Oznaka NAPOMENA ukazuje na važne informacije koje vam pomažu da bolje koristite proizvod. OPREZ: Oznaka OPREZ ukazuje na potencijalno oštećenje hardvera ili gubitak podataka i objašnjava vam kako da izbegnete problem. UPOZORENJE: UPOZORENJE ukazuje na opasnost od oštećenja opreme, telesnih povreda ili smrti. ©2018–2019. Dell Inc. ili njegove podružnice. Sva prava zadržana. Dell, EMC, i drugi žigovi su žigovi Dell Inc. ili njegovih podružnica.
Napomene, mere opreza i upozorenja NAPOMENA: Oznaka NAPOMENA ukazuje na važne informacije koje vam pomažu da bolje koristite proizvod. OPREZ: Oznaka OPREZ ukazuje na potencijalno oštećenje hardvera ili gubitak podataka i objašnjava vam kako da izbegnete problem. UPOZORENJE: UPOZORENJE ukazuje na opasnost od oštećenja opreme, telesnih povreda ili smrti. ©2018–2019. Dell Inc. ili njegove podružnice. Sva prava zadržana. Dell, EMC, i drugi žigovi su žigovi Dell Inc. ili njegovih podružnica.
Sadržaj 1 Rad na računaru............................................................................................................................7 Bezbednosna uputstva..........................................................................................................................................................7 Pre rada u unutrašnjosti računara.................................................................................................................................. 7 Bezbednosne mere...
Uklanjanje zvučnika........................................................................................................................................................42 Montiranje zvučnika...................................................................................................................................................... 45 Ventilator sistema...................................................................................................................................................
Kabl ekrana (eDP).............................................................................................................................................................. 110 Uklanjanje kabla ekrana................................................................................................................................................ 110 Postavljanje kabla ekrana.......................................................................................................................................
1 Rad na računaru Bezbednosna uputstva Preduslovi Koristite sledeće bezbednosne smernice kako biste zaštitili računar od mogućih oštećenja i osigurali ličnu bezbednost. Osim ako je drugačije navedeno, svaka procedura obuhvaćena ovim dokumentom pretpostavlja da postoje slijedeći uslovi: • • Pročitali ste bezbednosne informacije koje ste dobili uz računar. Komponenta se može zameniti ili, ako je kupljena odvojeno, montirati izvođenjem procedure uklanjanja u obrnutom redosledu.
5. Isključite računar i sve priključene uređaje iz pripadajućih električnih utičnica. 6. Pritisnite i zadržite taster za napajanje dok je računar isključen da biste uzemljili matičnu ploču. NAPOMENA: Da biste izbegli elektrostatičko pražnjenje, uzemljite se pomoću trake za uzemljenje ili povremeno dodirujte neobojenu metalnu površinu dok istovremeno dodirujete konektor na zadnjem delu računara.
• • • • Koristite ožičenu narukvicu za zaštitu od elektrostatičkog pražnjenja koja je valjano uzemljena. Upotreba bežičnih antistatičkih traka više nije dozvoljena, pošto ne obezbeđuju odgovarajuću zaštitu. Dodirivanje kućišta pre delova kojim se rukuje ne obezbeđuje odgovaraćuju zaštitu od elektrostatičkog pražnjenja na delovima kod kojih postoji povećan rizik od oštećenja uzrokovanih elektrostatičkim pražnjenjem.
Ukratko o zaštiti od elektrostatičkog pražnjenja Preporučujemo vam da svi tehničari, koji vrše servisiranje na terenu, koriste tradicionalne ožičene ESD narukvice sa uzemljenjem i zaštitnu antistatičku podlogu svaki put kada servisiraju proizvode Dell. Pored toga, veoma je važno da tehničari drže osetljive delove odvojeno od svih izolacionih delova kada vrše servisiranje i da koriste antistatičke kese za transport osetljivih komponenti.
2 Tehnologija i komponente U ovom odeljku su opisane tehnologije i komponente dostupne na sistemu. Teme: • • • • Funkcije USB-a USB tipa C HDMI 1.4a Karakteristike LED indikatora za dugme za napajanje Funkcije USB-a Univerzalna serijska magistrala ili USB je predstavljena 1996. godine. Značajno je pojednostavila vezu između matičnih računara i perifernih uređaja kao što su miševi, tastature, spoljne disk jedinice i štampači. Bacimo kratak pogled na USB evoluciju koji je prikazan u tabeli u nastavku.
• • USB 2.0 interfejs je prethodno imao četiri žice (napajanje, masa i par za diferencijalne podatke); USB 3.0/USB 3.1 Gen 1 dodaje još četiri žice za dva para diferencijalnih signala (prijem i slanje) za kombinovano ukupno osam veza u konektorima i kablovima. USB 3.0/USB 3.1 Gen 1 koristi dvosmerni interfejs za prenos podataka umesto polu-dupleks sistema u interfejsu USB 2.0. Ovo obezbeđuje povećanje teorijskog protoka od 10 puta.
sistemu Windows 7, podrška za SuperSpeed funkciju preći i na sistem Vista. Microsoft je to potvrdio navodeći da većina njihovih partnera deli mišljenje da bi i Vista trebalo da podrži USB 3.0/USB 3.1 Gen 1. USB tipa C USB tipa C je novi fizički konektor malih dimenzija. Konektor može da podrži različite nove USB standarde kao što su USB 3.1 i USB power delivery (USB PD). Alternativni režim USB tipa C je novi standard konektora koji je veoma malih dimenzija. Zauzima trećinu starog priključka za USB tipa A.
Thunderbolt 3 preko USB-a tipa C Thunderbolt 3 donosi Thunderbolt preko USB konektora tipa C, brzine do 40 Gb/s, stvarajući jedan kompaktni port koji može učiniti sve – pruža najbržu, najraznovrsniju vezu sa bilo kojom baznom stanicom, ekranom ili uređajem za podatke kao što je spoljašnji čvrsti disk. Thunderbolt 3 koristi USB konektor / port tipa C za povezivanje sa podržanim perifernim uređajima. 1. 2. 3. 4.
• • • 4K podrška (Podrška za 4k) – Omogućava video rezolucije mnogo veće od 1080 p i na taj način podržava prikaze sledeće generacije koji će parirati sistemima digitalnog bioskopa koji se koriste u mnogim komercijalnim bioskopima HDMI Micro Connector (HDMI mikro konektor) – Novi, manji konektor za telefone i druge prenosive uređaje, koji podržava video rezolucije do 1080p Automotive Connection System (Sistem povezivanja sa vozilom) – Novi kablovi i konektori za video sisteme u vozilima, koji su dizajniran
Dugme za napajanje sa čitačem otiska prste neće imati LED i koristiće dostupni LED sistema kao indikator statusa sistema • LED adaptera za napajanje: • ○ Konektor LED-a na adapteru za napajanje svetli belo kada se napajanje vrši preko utičnice. LED indikatora baterije: ○ Ako je računar priključen na električnu utičnicu, svjetla baterije funkcionišu na slijedeći način: 1. Neprekidno belo svetlo – Baterija se puni. LED se isključuje kada se punjenje dovrši.
3 Najvažnije komponente sistema 1. Poklopac osnove 3. Rashladni element 2. Port za DC ulaz 4.
5. 7. 9. 11. 13. 15. 17. Matična ploča Baterija Ploča čitača pametnih kartica Sklop ekrana LED ploču WLAN kartica Ventilator sistema 6. 8. 10. 12. 14. 16. 18. Solid state disk jedinica Zvučnici Sklop oslonca za dlan Ploča sa tasterima table osetljive na dodir Dugmasta baterija WWAN karticu NAPOMENA: Dell pruža listu komponenata i brojeva njihovih delova za originalnu kupljenu konfiguraciju sistema. Ovi delovi su dostupni u skladu sa pokrivenošću garancije koju je kupio klijent.
4 Rastavljanje i ponovno sastavljanje MicroSD kartica Uklanjanje microSD kartice Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Koraci 1. Gurnite microSD karticu da biste je odvojili od računara [1]. 2. Izvucite microSD karticu iz računara [2]. Postavljanje microSD kartice Koraci 1. Poravnajte microSD karticu sa odgovarajućim slotom na računaru [1]. 2. Umetnite microSD karticu u slot tako da klikne u ležište [2].
3. Sledite procedure u odeljku Posle rada u unutrašnjosti računara. Ležište SIM kartice Uklanjanje ležišta SIM kartice Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Koraci 1. Umetnite iglu u otvor ležišta SIM kartice i gurnite ka unutrašnjosti dok se ležište ne oslobodi [1, 2]. 2. Izvucite ležište SIM kartice iz računara [3].
Postavljanje ležišta SIM kartice Koraci 1. Postavite SIM karticu u ležište SIM kartice tako da metalni deo bude okrenut nagore [1]. 2. Poravnajte ležište SIM kartice sa slotom na računaru i pažljivo ga umetnite [2]. 3. Umetnite ležište za SIM karticu u slot tako da klikne u ležište [3].
4. Sledite procedure u odeljku Posle rada u unutrašnjosti računara. Poklopac osnove Uklanjanje poklopca osnove Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara 2. Uklonite microSD karticu. Koraci 1. Olabavite osam neispadajućih zavrtanja [1].
2. Pomoću plastične olovke [1], podignite poklopac osnove iz gornjeg levog ugla i nastavite da podižete stranicu da biste otvorili poklopac osnove [2].
3. Podignite i uklonite poklopac osnove iz računara.
Montiranje poklopca osnove Koraci 1. Poravnajte i postavite poklopac osnove na računaru.
2. Pritisnite ivice i strane poklopca osnove dok se ne smesti u ležište.
3. Pričvrstite osam neispadajućih zavrtanja da biste pričvrstili poklopac osnove za računar.
Sledeći koraci 1. Postavite microSD karticu. 2. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Baterija Bezbednosne mere za litijum-jonsku bateriju OPREZ: • Budite oprezni pri rukovanju litijum-jonskih baterija. • Ispraznite bateriju što je više moguće pre nego što je izvadite iz sistema. To možete da uradite tako što ćete isključiti adapter naizmenične struje sa sistema da biste omogućili da se isprazni baterija.
3. Olabavite dva neispadajuća zavrtnja da biste pričvrstili bateriju za oslonac za dlan [1]. 4. Gurnite bateriju ka unutra i podignite je sa oslonca za dlan [2].
Montiranje baterije Koraci 1. Poravnajte i umetnite bateriju na oslonac za dlan [1]. 2. Pritegnite dva neispadajuća zavrtnja da biste pričvrstili bateriju za oslonac za dlan [2].
3. Povežite kabl baterije sa konektorom na matičnoj ploči [1]. 4. Zalepite lepljivu traku da biste učvrstili konektor kabla baterije [2].
Sledeći koraci 1. Postavite poklopac osnove. 2. Postavite microSD karticu. 3. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara WWAN kartica Uklanjanje WWAN kartice Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. 2. 3. 4. 32 Uklonite jedan (M2x3) zavrtanj koji učvršćuje nosač WWAN kartice za matičnu ploču [1].
Postavljanje WWAN kartice Informacije o ovom zadatku OPREZ: Da biste sprečili oštećenje WWAN kartice, ne postavljajte kablove ispod nje. Koraci 1. 2. 3. 4. Umetnite WWAN karticu u konektor na matičnoj ploči [1]. Povežite WWAN kablove antene sa konektorima na WWAN kartici [2]. Postavite nosač WWAN kartice da biste povezali WWAN kablove antene sa WWAN karticom [3]. Postavite jedan (M2x3) zavrtanj da biste učvrstili nosač WWAN kartice za WWAN karticu [4].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. WLAN kartica Uklanjanje WLAN kartice Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. 2. 3. 4. 34 Uklonite jedan (M2x2) zavrtanj koji učvršćuje nosač WLAN kartice za matičnu ploču [1].
Montiranje WLAN kartice Informacije o ovom zadatku OPREZ: Da biste sprečili oštećenje bežične kartice, ne postavljajte kablove ispod nje. Koraci 1. 2. 3. 4. Ubacite WLAN karticu u konektor na matičnoj ploči [1]. Povežite WLAN kablove antene sa konektorima na WLAN kartici [2]. Postavite nosač WLAN kartice da biste povezali WLAN kablove antene sa WLAN karticom [3]. Postavite jedan (M2x3) zavrtanj da biste učvrstili nosač WLAN kartice za WLAN karticu [4].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Memorijski moduli Uklanjanje memorijskog modula Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. Povucite pričvrsne spone koje učvršćuju memorijski modul tako da memorijski modul iskoči iz ležišta [1]. 2.
Montiranje memorijskog modula Koraci 1. Poravnajte zarez na memorijskom modulu sa držačem na priključku memorijskog modula. 2. Pod uglom i do kraja gurnite memorijski modul u slot [1]. 3. Pritisnite memorijski modul dok ga pričvrsne spone ne učvrste [2]. NAPOMENA: Ako ne čujete klik, uklonite memorijski modul i ponovo ga instalirajte.
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Solid state disk jedinica Uklanjanje M.2 SSD diska Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. Uklonite dva (M2x3) zavrtnja koji pričvršćuju oslonac M.2 SSD diska za oslonac za dlan [1]. 2.
3. Uklonite jedan zavrtanj (M2x2) koji učvršćuje M.2 SSD za oslonac za dlan [1]. 4. Podignite M.2 SSD i uklonite ga iz računara [2].
Montiranje M.2 SSD diska Koraci 1. Postavite M.2 SSD u slot na osloncu za dlan [1]. 2. Postavite jedan (M2x2) zavrtanj da biste učvrstili M.2 SSD za oslonac za dlan [2].
3. Poravnajte i postavite oslonac SSD diska iznad M.2 SSD diska [1]. 4. Postavite dva (M2x3) zavrtnja da biste učvrstili oslonac SSD diska za oslonac za dlan [2].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Zvučnici Uklanjanje zvučnika Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. Izvucite kabl zvučnika iz konektora na matičnoj ploči [1]. 2. Odlepite lepljivu traku koja učvršćuje kabl zvučnika za oslonac za dlan [2].
3. Izvucite kabl table osetljive na dodir iz konektora na priključnoj ploči. 4. Odlepite lepljive trake i izvucite kabl zvučnika.
5. Podignite i uklonite zvučnike sa oslonca za dlan.
Montiranje zvučnika Koraci 1. Pomoću stubića za poravnanje i gumenih uvodnica postavite zvučnike u slotove na osloncu za dlan. 2. Provucite kabl zvučnika kroz kanale za usmeravanje.
3. Fiksirajte lepljivu traku koja učvršćuje kabl zvučnika za oslonac za dlan [1]. 4. Povežite kabl zvučnika sa konektorom na matičnoj ploči [2].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Ventilator sistema Uklanjanje ventilatora sistema Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. Izvucite kabl ventilatora sistema iz konektora na matičnoj ploči.
2. Uklonite dva (M2x5) zavrtnja koji učvršćuju ventilator sistema za oslonac za dlan [1]. 3. Podignite i uklonite ventilator sistema iz računara [2].
Montiranje ventilatora sistema Koraci 1. Postavite i poravnajte otvore za zavrtnje na ventilatoru sistema sa otvorima za zavrtnje na osloncu za dlan [1]. 2. Postavite dva (M2x5) zavrtnja koji učvršćuju ventilator sistema za oslonac za dlan [2].
3. Povežite kabl ventilatora sistema sa konektorom na matičnoj ploči.
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Rashladni element Uklanjanje ventilatora rashladnog elementa – UMA Preduslovi 1. 2. 3. 4. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Koraci 1. Postavite četiri neispadajućazavrtnja koji učvršćuju rashladni element za matičnu ploču [1].
Montiranje ventilatora rashladnog elementa – UMA Koraci 1. Postavite rashladni element na matičnu ploču i poravnajte otvore za zavrtnje na rashladnom elementu sa otvorima za zavrtnje na matičnoj ploči [1]. 2. Prema određenom redosledu (naznačenom na rashladnom elementu) pritegnite četiri neispadajuća zavrtnja kojima je rashladni element pričvršćen za matičnu ploču [2]. Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu.
Koraci 1. Uklonite dva zavrtnja (M2x4) kojima je nosač tipa C pričvršćen za matičnu ploču [1]. 2. Podignite i uklonite nosač tipa C iz računara [2]. 3. Isključite kabl za port DC ulaza iz konektora na matičnoj ploči i uklonite port DC ulaza sa računara [1, 2].
Postavljanje porta za DC ulaz Koraci 1. Postavite port za DC ulaz u odgovarajući slot na računaru [1]. 2. Povežite kabl porta za DC ulaz sa konektorom na matičnoj ploči [2].
3. Postavite nosač tipa C u odgovarajući slot na računaru [1]. 4. Postavite dva (M2x4) zavrtnja da biste učvrstili nosač tipa C za oslonac za dlan [2].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. LED ploča Uklanjanje LED ploče Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Koraci 1. Izvucite kabl LED ploče iz konektora na matičnoj ploči [1]. 2. Izvucite kabl LED ploče [2].
3. Odlepite lepljivu traku koja pričvršćuje konektor kabla LED ploče za LED ploču [1]. 4. Odlepite sivu lepljivu traku koja pričvršćuje LED ploču [2].
5. Uklonite jedan (M2x2,5) zavrtanj koji pričvršćuje LED ploču za oslonac za dlan [1]. 6. Podignite LED ploču i uklonite je iz računara [2].
Montiranje LED ploče Koraci 1. Postavite LED ploču i poravnajte otvor za zavrtanj na LED ploči sa otvorom za zavrtanj na osloncu za dlan [1]. 2. Postavite jedan (M2x2,5) zavrtanj da biste učvrstili LED ploču za oslonac za dlan [2].
3. Zalepite sivu lepljivu traku da biste učvrstili LED ploču [1]. 4. Zalepite lepljivu traku da biste učvrstili LED ploču [2].
5. Povežite kabl LED ploče sa konektorom na matičnoj ploči i provucite kabl LED ploče [1, 2].
Sledeći koraci 1. 2. 3. 4. 5. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Ploča sa tasterima table osetljive na dodir Uklanjanje ploče sa tasterima table osetljive na dodir Preduslovi 1. 2. 3. 4. 5. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Koraci 1.
Montiranje ploče sa tasterima table osetljive na dodir Koraci 1. Postavite ploču sa tasterima table osetljive na dodir u slot na osloncu za dlan [1]. 2. Postavite dva (M2x3) zavrtnja da biste pričvrstili ploču sa tasterima table osetljive na dodir za sistem [2].
3. Povežite kabl ploče sa tasterima table osetljive na dodir sa konektorom na ploči table osetljive na dodir.
Sledeći koraci 1. 2. 3. 4. 5. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Matična ploča Uklanjanje matične ploče Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Uklonite rashladni element. Uklonite ventilator sistema. Uklonite DC ulaz .
2. Uklonite jedan (M2,5x4) zavrtanj koji učvršćuje nosač čitača otiska prsta za matičnu ploču [1]. 3. Podignite i uklonite nosač čitača otiska prista iz računara [2]. 4. Izvucite port čitača otiska prsta [3].
5. 6. 7. 8. Odlepite lepljivu traku i izvucite kabl iz konektora na matičnoj ploči [1]. Uklonite jedan (M2x4) zavrtanj koji učvršćuje nosač eDP kabla za matičnu ploču [2]. Uklonite nosač eDP kabla i izvucite ga iz računara [3]. Podignite rezu i izvucite eDP kabl iz konektora na matičnoj ploči [4].
9. Uklonite dugmastu bateriju sa oslonca za dlan.
10. Uklonite tri (M2x2) zavrtnja i jedan (M2,5x4) zavrtanj da biste pričvrstili matičnu ploču za oslonac za dlan [1]. 11. Podignite i uklonite matičnu ploču iz računara [2].
Montiranje matične ploče Koraci 1. Poravnajte i postavite matičnu ploču na oslonac za dlan [1]. 2. Postavite tri (M2x2) zavrtnja i jedan (M2,5x4) zavrtanj da biste pričvrstili matičnu ploču za oslonac za dlan [2].
3. Postavite dugmastu bateriju u odgovarajući slot na osloncu za dlan.
4. 5. 6. 7. 72 Povežite kabl sa konektorom na matičnoj ploči i zalepite lepljivu traku [1]. Povežite eDP kabl sa konektorom na matičnoj ploči [2]. Postavite oslonac eDP kabla iznad eDP konektora [3]. Postavite zavrtanj (M2x4) da biste pričvrstili nosač eDP kabla za matičnu ploču [4].
8. Povežite kabl čitača otiska prsta sa konektorom na matičnoj ploči [1]. 9. Postavite oslonac čitača otiska prsta [2]. 10. Postavite jedan zavrtanj (M2,5x4) da biste pričvrstili nosač čitača otiska prsta za matičnu ploču [3].
11. Priključite sledeće kablove: a. USH kabl [1]. b. Kabl LED ploče [2]. c. kabl table osetljive na dodir [3].
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Postavite WWAN karticu. Postavite WLAN karticu. Postavite DC ulaz. Postavite memorijski modul. Postavite ventilator sistema. Postavite rashladni element. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Dugmasta baterija Uklanjanje dugmaste baterije Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Uklonite rashladni element. Uklonite memorijski modul. Uklonite ventilator sistema. Uklonite DC ulaz. Uklonite WLAN karticu. Uklonite WWAN karticu. Uklonite matičnu ploču. Koraci Okrenite matičnu ploču i izvucite kabl dugmaste baterije iz konektora na matičnoj ploči. Montiranje dugmaste baterije Koraci Okrenite matičnu ploču i povežite kabl dugmaste baterije sa konektorom na matičnoj ploči.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Postavite matičnu ploču. Postavite WWAN karticu. Postavite WLAN karticu. Postavite DC ulaz. Postavite memorijski modul. Postavite ventilator sistema. Postavite rashladni element. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Sklop ekrana Uklanjanje sklopa ekrana Preduslovi 1. 2. 3. 4.
Koraci 1. 2. 3. 4. Odlepite lepljivu traku i izvucite kabl iz konektora na matičnoj ploči [1]. Uklonite jedan (M2x4) zavrtanj koji učvršćuje nosač eDP kabla za matičnu ploču [2]. Podignite i uklonite nosač eDP kabla sa matične ploče [3]. Isključite i izvucite eDP kabl [4]. 5. Otvorite sklop ekrana pod uglom od 180 stepeni i okrenite sistem, pa postavite sistem na ravnu površinu.
6. Postavite četiri (M2,5x3) zavrtnja koji pričvršćuju sklop ekrana za kućište sistema [1]. 7. Uklonite sklop ekrana iz sistema [2].
Montiranje sklopa ekrana Informacije o ovom zadatku NAPOMENA: Vodite računa da su zglobovi otvoreni do maksimuma pre nego što postavite sklop ekrana na sklop oslonca za dlan i tastature. Koraci 1. Poravnajte i postavite kućište sistema ispod zglobova sklopa ekrana [1]. 2. Postavite četiri (M2,5x3) zavrtnja koji pričvršćuju sklop ekrana za kućište sistema [2].
3. Postavite kućište sistema na sklop ekrana.
4. 5. 6. 7. 82 Povežite kabl sa konektorom na matičnoj ploči i zalepite lepljivu traku [1]. Ponovo provucite eDP kabl i povežite ga sa eDP konektorom [2]. Postavite nosač eDP kabla na matičnu ploču [3]. Uklonite jedan (M2x4) zavrtanj koji učvršćuje nosač eDP kabla za matičnu ploču [4].
Sledeći koraci 1. 2. 3. 4. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Tastatura Uklanjanje tastature Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Uklonite memorijski modul. Uklonite ventilator sistema. Uklonite DC ulaz . Uklonite WLAN karticu.
10. Uklonite WWAN karticu. 11. Uklonite matičnu ploču. NAPOMENA: Matična ploča može da se ukloni sa pričvršćenim rashladnim elementom. 12. Uklonite dugmastu bateriju. Koraci 1. Uklonite lepljivu traku koja pričvršćuje tastaturu i čitač pametne kartice. 2. Podignite rezu i izvucite kabl pozadinskog osvetljenja i kabl tastature iz konektora na tabli osetljivoj na dodir.
3. Uklonite 19 (M2x2) zavrtanja koji pričvršćuju tastaturu za oslonac za dlan [1]. 4. Uklonite tastaturu iz računara [2].
Postavljanje tastature Koraci 1. Poravnajte i postavite tastaturu na sklop oslonca za dlan [1]. 2. Postavite 19 (M2x2) zavrtanja da biste pričvrstili tastaturu za oslonac za dlan [2].
3. Povežite kabl pozadinskog osvetljenja i kabl tastature sa konektorima na tabli osetljivoj na dodir.
4. Pričvrstite lepljivu traku koja pričvršćuje tastaturu i ploču pametne kartice.
Sledeći koraci 1. Postavite dugmastu bateriju. 2. Postavite matičnu ploču. NAPOMENA: Matična ploča može da se postavi sa pričvršćenim rashladnim elementom. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Postavite WWAN karticu. Postavite WLAN karticu. Postavite DC ulaz. Postavite ventilator sistema. Postavite memorijski modul. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara.
Montiranje nosača tastature Koraci 1. Poravnajte i postavite tastaturu na nosač tastature [1]. 2. Postavite četiri (M2x2) zavrtanja koji pričvršćuju tastaturu za nosač tastature [2].
Sledeći koraci 1. Postavite tastaturu. 2. Postavite dugmastu bateriju. 3. Postavite matičnu ploču. NAPOMENA: Matična ploča može da se postavi sa pričvršćenim rashladnim elementom. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Postavite WWAN karticu. Postavite WLAN karticu. Postavite DC ulaz. Postavite memorijski modul. Postavite ventilator sistema. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara.
Ploča čitača pametne kartice Uklanjanje ploče čitača pametne kartice Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Uklonite memorijski modul. Uklonite ventilator sistema. Uklonite DC ulaz. Uklonite WLAN karticu. Uklonite WWAN karticu. Uklonite matičnu ploču. Uklonite dugmastu bateriju. Uklonite tastaturu. Koraci 1.
Montiranje ploče čitača pametne kartice Koraci 1. Poravnajte i postavite ploču čitača pametne kartice na oslonac za dlan [1]. 2. Postavite dva zavrtnja (M2x2,5) koji učvršćuju ploču čitača pametne kartice za oslonac za dlan [2].
3. Ponovo provucite kabl čitača pametne kartice.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Postavite tastaturu. Postavite dugmastu bateriju. Postavite matičnu ploču. Postavite WWAN karticu. Postavite WLAN karticu. Postavite DC ulaz. Postavite memorijski modul. Postavite ventilator sistema. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Okno ekrana Uklanjanje okvira ekrana Preduslovi 1. 2. 3. 4. 5.
Koraci 1. NAPOMENA: Okvir ekrana ne može ponovo da se koristi nakon uklanjanja. Koristite plastičnu olovku da biste pažljivo otvorili žlebove blizu levih i desnih zglobova pri donjoj ivici okvira ekrana [1]. 2. Pažljivo otvorite unutrašnju ivicu okvira ekrana, a zatim otvorite unutrašnju ivicu leve i desne strane okvira ekrana [2]. 3. Podignite okvir ekrana sa sklopa ekrana.
Montiranje okvira ekrana Koraci Poravnajte okvir ekrana sa sklopom ekrana i pažljivo umetnite okvir ekrana u ležište.
Rastavljanje i ponovno sastavljanje
Sledeći koraci 1. 2. 3. 4. 5. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Poklopci zglobova Uklanjanje poklopaca zglobova Preduslovi 1. 2. 3. 4. 5. 6. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite sklop ekrana. Uklonite okvir ekrana. Koraci 1.
Montiranje poklopaca zglobova Koraci 1. Postavite poklopce zglobova i gurnite ka spolja na zglobovima ekrana [1]. 2. Postavite dva (M2x3) zavrtnja da biste pričvrstili poklopce zglobova za zglobove ekrana.
Sledeći koraci 1. 2. 3. 4. 5. 6. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Zglobovi ekrana Uklanjanje zgloba ekrana Preduslovi 1. 2. 3. 4. 5. 6. 7. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite sklop ekrana. Uklonite okvir ekrana. Uklonite poklopce zglobova.
Koraci 1. Uklonite četiri zavrtnja (M2,5x3) da biste pričvrstili zglob ekrana za sklop ekrana [1]. 2. Uklonite zglobove ekrana sa zadnjeg poklopca ekrana [2]. Postavljanje zgloba ekrana Koraci 1. Postavite zglob ekrana na sklop ekrana. 2. Postavite četiri zavrtnja (M2,5x3) da biste pričvrstili zglob ekrana za sklop ekrana.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. Postavite poklopce zglobova. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Ploča ekrana Uklanjanje ploče ekrana Preduslovi 1. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. 2. Uklonite microSD karticu. 3. Uklonite poklopac osnove.
4. 5. 6. 7. 8. Uklonite bateriju. Uklonite sklop ekrana. Uklonite okvir ekrana. Uklonite poklopce zglobova. Uklonite zglobove ekrana. Koraci 1. Uklonite dva (M2x2) zavrtnja koji pričvršćuju ploču ekrana za sklop ekrana [1] i podignite i okrenite ploču ekrana da biste pristupili kablu ekrana [2]. 2. Zalepite izolir traku [1] da biste pričvrstili konektor kabla ekrana. 3. Podignite rezu i izvucite kabl ekrana sa konektora na ploči ekrana [2, 3].
Rastavljanje i ponovno sastavljanje 105
Postavljanje ploče ekrana Koraci 1. Povežite kabl ekrana sa konektorom i zatvorite rezu [1, 2]. 2. Zalepite lepljivu traku da biste pričvrstili konektor kabla ekrana [3]. 3. Postavite dva (M2x2) zavrtnja da biste pričvrstili ploču ekrana za sklop ekrana.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. Postavite zglobove ekrana. Postavite poklopce zglobova. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Kamera Uklanjanje kamere Preduslovi 1. 2. 3. 4. 5. 6. 7. Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove. Uklonite bateriju. Uklonite sklop ekrana.
8. Uklonite zglobove ekrana. 9. Uklonite ploču ekrana. Koraci Izvucite kabl kamere sa konektora na modulu kamere . Postavljanje kamere Koraci 1. Umetnite kameru u slot na zadnjem poklopcu ekrana .
2. Povežite kabl kamere sa konektorom i zalepite traku iznad konektora kamere.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. Postavite ploču ekrana. Postavite zglobove ekrana. Postavite poklopce zglobova. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Kabl ekrana (eDP) Uklanjanje kabla ekrana Preduslovi 1. 2. 3. 4. 5. 6. 110 Sledite proceduru u odeljku Pre rada u unutrašnjosti računara. Uklonite microSD karticu. Uklonite poklopac osnove.
7. 8. 9. 10. Uklonite poklopce zglobova. Uklonite zglobove ekrana. Uklonite ploču ekrana. Uklonite kameru. Koraci Odlepite izolir traku i izvucite kabl ekrana da biste ga odvojili od lepljive trake i podignite ga sa zadnjeg poklopca ekrana. Postavljanje kabla ekrana Koraci 1. Pričvrstite kabl ekrana na zadnji poklopac ekrana. 2. Zalepite izolir traku i pričvrstite kabl ekrana za zadnji poklopac ekrana.
Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Postavite kameru. Postavite ploču ekrana. Postavite zglobove ekrana. Postavite poklopce zglobova. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara. Sklop zadnjeg poklopca ekrana Postavljanje zadnjeg poklopca ekrana Preduslovi 1. 2. 3. 4. 5. 6. 7. 8. 9. 112 Sledite proceduru u odeljku Pre rada u unutrašnjosti računara.
10. Uklonite kameru. 11. Uklonite kabl ekrana. Informacije o ovom zadatku Nakon obavljanja prethodno navedenih koraka ostaje vam zadnji poklopac ekrana. Sledeći koraci 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Postavite kabl ekrana. Postavite kameru. Postavite ploču ekrana. Postavite zglobove ekrana. Postavite poklopce zglobova. Postavite okvir ekrana. Postavite sklop ekrana. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara.
3. 4. 5. 6. 7. 8. 9. 10. 11. Uklonite poklopac osnove. Uklonite bateriju. Uklonite zvučnik. Uklonite memorijski modul. Uklonite ventilator sistema. Uklonite DC ulaz . Uklonite WLAN karticu. Uklonite WWAN karticu. Uklonite matičnu ploču. NAPOMENA: Matična ploča može da se ukloni sa pričvršćenim rashladnim elementom. 12. Uklonite dugmastu bateriju. 13. Uklonite tastaturu. 14. Uklonite ploču čitača pametne kartice.
9. 10. 11. 12. 13. 14. Postavite ventilator sistema. Postavite zvučnik. Postavite bateriju. Postavite poklopac osnove. Postavite microSD karticu. Sledite proceduru u odeljku Posle rada u unutrašnjosti računara.
5 Rešavanje problema Poboljšana procena sistema pre pokretanja (ePSA) - dijagnostika Informacije o ovom zadatku ePSA dijagnostika (takođe se naziva dijagnostika sistema) vrši sveobuhvatnu proveru hardvera. ePSA je ugrađen u BIOS i BIOS ga pokreće interno.
Na primer, svetlo za status napajanja i baterije treperi žuto dva puta nakon čega sledi pauza, a zatim treperi belo tri puta nakon čega sledi pauza. Ovaj šablon 2,3 se nastavlja dok se računar ne isključi, što pokazuje da memorija ili RAM memorija nisu detektovane. Tabela u nastavku pokazuje različite svetlosne šablone za status napajanja i baterije, kao i povezane probleme. Tabela 3.
6 Dobijanje pomoći Teme: • Kontaktiranje kompanije Dell Kontaktiranje kompanije Dell Preduslovi NAPOMENA: Ako nemate aktivnu vezu sa Internetom, kontakt informacije možete pronaći na fakturi, otpremnici, računu ili katalogu Dell proizvoda. Informacije o ovom zadatku Dell nudi nekoliko opcija za onlajn i telefonsku podršku i servis. Dostupnost zavisi od zemlje i proizvoda, a neke usluge možda neće biti dostupne u vašoj oblasti.