Dell Latitude 5400 Servis El Kitabı Resmi Model: P98G Resmi Tip: P98G001
Notlar, dikkat edilecek noktalar ve uyarılar NOT NOT, ürününüzü daha iyi kullanmanıza yardımcı olacak önemli bilgiler sağlar. DİKKAT DİKKAT, donanım hasarı veya veri kaybı olasılığını gösterir ve sorunu nasıl önleyeceğinizi bildirir. UYARI UYARI, mülk hasarı, kişisel yaralanma veya ölüm potansiyeline işaret eder. © 2019 Dell Inc. veya bağlı kuruluşları. Tüm hakları saklıdır. Dell, EMC ve diğer ticari markalar, Dell Inc. veya bağlı kuruluşlarının ticari markalarıdır.
İçindekiler 1 Bilgisayarınızda Çalışma................................................................................................................ 6 Güvenlik talimatları.................................................................................................................................................................6 Bilgisayarınızın içinde çalışmadan önce..........................................................................................................................
Katı hal sürücü braketini çıkarma................................................................................................................................. 40 Katı hal sürücü braketini takma.....................................................................................................................................41 İç çerçeve.........................................................................................................................................................................
Ekran (eDP) kablosu...........................................................................................................................................................101 Ekran kablosunu çıkarma..............................................................................................................................................101 Ekran kablosunu takma................................................................................................................................................
1 Bilgisayarınızda Çalışma Güvenlik talimatları Önkosullar Bilgisayarınızı olası hasarlardan korumak ve kendi kişisel güvenliğinizi sağlamak için aşağıdaki güvenlik yönergelerine uyun. Aksi belirtilmedikçe, bu belgede verilen her yordamda aşağıdaki koşulların geçerli olduğu varsayılır: • • Bilgisayarınızla birlikte gelen güvenlik bilgilerini okudunuz. Çıkarma yordamı ters sırayla uygulanarak bir bileşen değiştirilebilir veya (ayrı satın alınmışsa) takılabilir.
5. Bilgisayarınızı ve tüm bağlı aygıtları elektrik prizlerinden çıkarın. 6. Sistem kartını topraklamak için, sistem bağlantısı yokken güç düğmesini basılı tutun. NOT Elektrostatik boşalımı önlemek için bir bilek topraklama kayışı kullanarak ya da bilgisayarın arkasındaki konnektör gibi boyanmamış metal yüzeylere sık sık dokunarak kendinizi topraklayın. Güvenlik önlemleri Güvenlik önlemleri bölümü, herhangi bir sökme talimatını yerine getirmeden önce uygulanması gereken temel adımları anlatmaktadır.
ESD saha servis kiti İzlenmeyen Saha Servis kiti en yaygın kullanılan servis kitidir. Her bir Saha Servis kiti üç ana bileşenden oluşur: anti statik mat, bilek kayışı ve bağlama teli. ESD saha servis kiti bileşenleri Bir ESD saha servis kitinin bileşenleri şunlardır: • • • • • • • Anti-statik Mat – Anti-statik mat dağıtıcıdır ve servis prosedürleri sırasında parçalar matın üzerine yerleştirilebilir.
4. Yüke yakın durun. Omurganıza ne kadar yakın olursa belinize o kadar az yük bindirir. 5. Yükü kaldırırken veya indirirken sırtınızı dik tutun. Vücut ağırlığınızı yüke vermeyin. Vücudunuzu ve sırtınızı döndürmeyin. 6. Yükü yere bırakırken aynı tekniği kullanın. Bilgisayarınızın içinde çalıştıktan sonra Bu görev ile ilgili Herhangi bir parça değiştirme işleminden sonra, bilgisayarınızı açmadan önce harici aygıtları, kartları, kabloları vs. taktığınızdan emin olun. Adimlar 1.
2 Teknoloji ve bileşenler Bu bölümde, sistemde mevcut olan teknoloji ve bileşenlerle ilgili ayrıntılar verilmektedir. Konular: • • • • USB özellikleri C Tipi USB HDMI 1.4a Güç düğmesi LED’i davranışı USB özellikleri Evrensel Seri Veri Yolu veya USB, 1996 yılında tanıtılmıştır. Ana bilgisayarlar ile fare, klavye, harici sürücü ve yazıcı gibi çevresel aygıtlar arasındaki bağlantıyı önemli ölçüde basitleştirdi. Aşağıdaki tabloda USB gelişimine hızlıca göz atabileceğiniz referanslar listelenmiştir. Tablo 1.
• • USB 2.0, daha önce dört tele sahipti (güç, topraklama ve diferansiyel verileri için bir çift kablo); USB 3.0/USB 3.1 Gen 1'de ise konektörler ve kablolama içindeki toplam sekiz bağlantı kombinasyonu için iki çift diferansiyel sinyali (alıcı ve verici) için dört kablo daha eklenir. USB 2.0'ın yarım dupleks düzenlemesi yerine USB 3.0/USB 3.1 Gen 1'de çift yönlü veri arabirim kullanılır. Bu da teorik olarak bant genişliğine 10 kat artış getirir.
C Tipi USB C Tipi USB yeni, çok küçük bir fiziksel konnektördür. Konnektörün kendisi USB 3.1 ve USB güç dağıtımı (USB PD) gibi ilgiyle karşılanan çeşitli yeni USB standartlarını destekleyebilmektedir. Alternatif Mod C Tipi USB çok küçük olan yeni bir konnektör standardıdır. Eski A Tipi USB fişinin boyutunun üçte biri kadardır. Bu, her cihazın kullanabilmesi gereken tek bir konnektör standardıdır.
USB Tip C üzerinden Thunderbolt 3 Thunderbolt 3 tüm bunları sağlayan kompakt bir bağlantı noktası oluşturur ve en fazla 40 Gb/Sn hızda Thunderbolt C Tipi USB'ye getirilir herhangi dock, görüntüleme veya bir harici sabit sürücü gibi veri aygıtı için en hızlı, en çok yönlü bağlantı sunulur. Thunderbolt 3 desteklenen çevre birimlere bağlanmak için C Tipi USB konnektörü/bağlantı noktası kullanır. 1. 2. 3. 4.
HDMI'ın Avantajları • • • • • Kaliteli HDMI, sıkıştırılmamış dijital ses ve videoyu en yüksek, en canlı görüntü kalitesinde aktarır Düşük maliyetli HDMI hem dijital arabirimin kalite ve işlevselliğini sağlarken hem de sıkıştırılmamış video formatlarını basit ve uygun maliyetli biçimde sunar Ses HDMI standart stereodan çok kanallı surround sese kadar pek çok ses formatını destekler HDMI, video ve çok kanallı sesi tek bir kabloda birleştirerek şu anda A/V sistemlerinde kullanılan çok sayıda kablonun neden ol
Parmak izi okuyuculu güç düğmesinde LED yoktur ve sistem durumunu göstermek için sistemdeki var olan LED'ler kullanılır • Güç Adaptörü LED'i: • • Güç elektrik prizinden sağlandığında güç adaptörü konnektöründeki LED beyaz yanar. Pil Göstergesi LED'i: • Bilgisayar bir elektrik prizine bağlıysa, pil durum ışığı aşağıdaki gibi yanar: • 1. Kesintisiz beyaz - pil şarj oluyor. Şarj tamamlandığında LED söner. Bilgisayar pille çalışıyorsa pil ışığı aşağıdaki gibi yanar: • 1.
3 Sisteminizin ana bileşenleri 1. Taban kapağı 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. DC girişi bağlantı noktası Sistem fanı Sistem kartı Pil İç çerçeve Hoparlörler Akıllı Kart okuyucu Dokunmatik yüzey düğmesi kartı LED Kartı Avuç içi dayanağı aksamı Ekran aksamı Katı-hal sürücüsü Bellek modülü WLAN kartı Düğme pil NOT Dell, satın alınan orijinal sistem yapılandırması için bileşenlerin ve parça numaralarının bir listesini sağlar. Bu parçalar, müşteri tarafından satın alınan garanti kapsamları doğrultusunda kullanılabilir.
4 Sökme ve Takma MicroSD kart microSD Kartını Çıkarma Önkosullar 1. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedüre uyun. Adimlar 1. MicroSD kartı ittirerek bilgisayardan serbest bırakın [1]. 2. MicroSD kartı kaydırarak bilgisayarın dışına çıkarın [2]. microSD kartını takma Adimlar 1. MicroSD kartı bilgisayarın üzerindeki yuvasına yerleştirin [1]. 2. MicroSD kartı kaydırarak yerine oturtun [2].
3. Bilgisayarınızda çalıştıktan sonra bölümündeki prosedürü takip edin. Taban kapağı Alt kapağın çıkarılması Önkosullar 1. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin 2. MicroSD kartı çıkarın. Adimlar 1. Sekiz tutucu vidayı gevşetin [1].
2. Plastik bir çubukla [1] alt kapağı üst sol köşesinden kanırtarak kaldırın ve alt kapağı açmak üzere yanlardan kaldırmaya devam edin [2].
3. Alt kapağı kaldırarak bilgisayardan çıkarın. Alt kapağı takma Adimlar 1. Alt kapağı bilgisayara hizalayıp yerleştirin.
2. Alt kapak yerine oturana kadar kenarlarına ve yanlarına bastırın.
3. Alt kapağı bilgisayara sabitlemek için sekiz tutucu vidayı sıkın.
Sonraki Adimlar 1. MicroSD kartı yerine takın. 2. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Pil Lityum-iyon pil önlemleri DİKKAT • Lityum iyon pilleri kullanırken dikkatli olun. • Pili sistemden çıkarmadan önce olabildiğince boşaltın. Bu işlem, pilin boşalması için AC adaptörü sistemden ayırarak yapılabilir. • Pili ezmeyin, düşürmeyin, kesmeyin veya yabancı nesnelerle delmeyin.
2. Pili avuç içi dayanağına sabitleyen tek tutucu vidayı gevşetin [1]. 3. Pili içeri doğru kaydırarak avuç içi dayanağından kaldırın [2].
Pili takma Adimlar 1. Pili avuç içi dayanağına hizalayın ve kaydırın [1]. 2. Pili avuç içi dayanağına sabitlemek için tek tutucu vidayı sıkın [2].
3. Pil kablosunu sistem kartındaki konnektöre takın.
Sonraki Adimlar 1. Alt kapağı yerine takın. 2. MicroSD kartı yerine takın. 3. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü takip edin WLAN kartı WLAN Kartını Çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. WLAN kartı braketini sistem kartına sabitleyen tek (M2x3) vidayı çıkarın [1]. 2. WLAN anten kablolarını sabitleyen WLAN kartı braketini çıkarın [2]. 3.
WLAN Kartını Takma Bu görev ile ilgili DİKKAT WLAN kartının hasar görmesini önlemek için altına herhangi bir kablo yerleştirmeyin. Adimlar 1. WLAN kartını sistem kartındaki konnektöre takın [1]. 2. WLAN anten kablolarını WLAN kartındaki konnektörlere takın [2]. 3. WLAN anten kablolarını WLAN kartına sabitlemek için WLAN kartı braketini yerleştirin [3]. 4. WLAN kartı braketini WLAN kartına sabitlemek için tek (M2x3) vidayı yerine takın [4].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Düğme pil Düğme pili çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. Düğme pil kablosunu sistem kartındaki konnektörden çıkarın [1]. 2. Düğme pili sistem kartından kaldırın [2].
Düğme pili takma Adimlar 1. Düğme pili sistem kartına yerleştirin [1]. 2. Düğme pil kablosunu sistem kartındaki konnektöre takın [2].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Bellek modülleri Bellek modülünü çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. Bellek modülü yerinden çıkana kadar modülü sabitleyen klipsleri kaldırın [1]. 2.
Bellek modülünü takma Adimlar 1. Bellek modülünün üstündeki çentiği, bellek modülü yuvasındaki tırnakla hizalayın. 2. Bellek modülünü yuvanın içine eğik olarak sıkıca oturtun [1]. 3. Bellek modülü klipsler ile sabitleninceye kadar aşağıya doğru bastırın [2]. NOT Tık sesi duymazsanız, bellek modülünü çıkarıp yeniden takın.
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. DC girişi bağlantı noktası DC girişi bağlantı noktasını çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. Tip C braketi sistem kartına sabitleyen iki (M2x5) vidayı sökün [1]. 2.
3. DC girişi bağlantı noktası kablosunu sistem kartındaki konnektörden ayırın ve DC girişi bağlantı noktasını bilgisayardan çıkarın [1, 2].
DC girişi bağlantı noktasını takma Adimlar 1. DC girişi bağlantı noktasını bilgisayardaki yuvasına yerleştirin [1]. 2. DC girişi bağlantı noktası kablosunu sistem kartındaki konnektöre takın [2].
3. Tip C braketini bilgisayardaki yuvasına yerleştirin [1]. 4. Tip C braketini avuç içi dayanağına sabitleyen iki (M2x5) vidayı yerine takın [2].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Katı hal sürücü M.2 SSD'yi çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. M.2 SSD destek braketini avuç içi dayanağına sabitleyen iki (M2x3) vidayı çıkarın [1]. 2. SSD destek braketini hafifçe döndürüp M.
3. SSD'yi SSD termal plakasından çıkarın. M.2 SSD takma Adimlar 1. M.2 SSD'yi avuç içi dayanağındaki yuvasına yerleştirin [1]. 2. SSD destek braketini M.2 SSD'nin üzerine hizalayıp yerleştirin [2]. 3. SSD destek braketini avuç içi dayanağına sabitlemek için iki (M2x3) vidayı yerine takın [3].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Katı hal sürücü braketi Katı hal sürücü braketini çıkarma Önkosullar 1. 2. 3. 4. 5. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. microSD kartını çıkarın. Alt kapağı çıkarın. Pili çıkarın. M.2 SSD'yi çıkarın Adimlar 1. Braketi avuç içi dayanağına [1] sabitleyen tek (M2x3) vidayı sökün. 2.
Katı hal sürücü braketini takma Adimlar 1. Braketi hizalayın ve avuç içi dayanağı [1] üzerindeki yuvaya yerleştirin. 2. Braketi avuç içi dayanağına [2] sabitlemek için tek (M2x3) vidayı yerine takın.
Sonraki Adimlar 1. 2. 3. 4. 5. M.2 SSD'yi yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. İç çerçeve İç çerçeveyi çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. microSD kartını çıkarın. Alt kapağı çıkarın. Pili çıkarın. WLAN kartını çıkarın. M.2 SSD'yi çıkarın M.2 SSD braketini çıkarın. Adimlar 1.
2. İç çerçeveyi sistem kartına [1] sabitleyen beş (M2x5) vidayı çıkarın. 3. İç çerçeveyi sistem kasasına [2] sabitleyen altı (M2x3) vidayı çıkarın. 4. İç çerçeveyi sistem kasasından [3] kaldırın.
İç çerçeveyi takma Adimlar 1. İç çerçeveyi sistem kasasına hizalayarak yerleştirin [1]. 2. İç çerçeveyi sistem kasasına [2] sabitlemek için altı (M2x3) vidayı yerine takın. 3. İç çerçeveyi sistem kasasına [3] sabitlemek için beş (M2x5) vidayı yerine takın.
4. WLAN anten kablolarını yeniden yönlendirin.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. M.2 SSD kızağını yerine takın. M.2 SSD'yi yerine takın. WLAN kartını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Akıllı Kart okuyucu SmartCard okuyucuyu çıkarma Önkosullar 1. 2. 3. 4. 5. 6. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. microSD kartını çıkarın. Alt kapağı çıkarın. Pili çıkarın. WLAN kartını çıkarın.
3. Akıllı kart okuyucusunu avuç içi dayanağına sabitleyen üç (M2x3) vidayı sökün [1]. 4. Akıllı kart okuyucu kartını avuç içi dayanağından kaldırın [2].
SmartCard okuyucuyu takma Adimlar 1. Akıllı kart okuyucu kartını avuç içi dayanağına yerleştirin [1]. 2. Akıllı kart okuyucusunu avuç içi dayanağına [2] sabitlemek için üç (M2x3) vidayı yerine takın.
3. SmartCard okuyucu FFC'sini USH kartındaki konektöre bağlayın [1]. 4. Akıllı kart FFC'sini avuç içi dayanağına [2] yapıştırın.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. İç çerçeveyi yerine takın. WLAN kartını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Dokunmatik yüzey düğmeleri Dokunmatik yüzey düğme kartını çıkarma Önkosullar 1. 2. 3. 4. 5. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Hoparlörü çıkarın. Adimlar 1.
3. Mandalı açın ve dokunmatik yüzey düğme kartı kablosunu dokunmatik yüzey kartındaki konnektörden ayırın [1, 2].
4. Dokunmatik yüzey düğme braketini avuç içi dayanağına sabitleyen iki vidayı (M2x3) sökün [1]. 5. Dokunmatik yüzey düğme kartı braketini bilgisayardan kaldırın [2]. Dokunmatik yüzey düğme kartını takma Adimlar 1. Dokunmatik yüzey düğme kartını avuç içi dayanağındaki yuvaya yerleştirin [1]. 2. Güç düğmesi kartını avuç içi dayanağı ve klavye aksamına sabitleyen iki (M2x3) vidayı yerine takın [2].
3. Dokunmatik yüzey düğme kartı kablosunu dokunmatik yüzey kartındaki konnektöre takın [1, 2].
4. Smartcard okuyucu Esnek Düz Kablosunu (FFC) USH kartına takın [1]. 5. FFC'yi avuç içi dayanağına yapıştırın [2]. Sonraki Adimlar 1. 2. 3. 4. 5. Hoparlörü yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. LED Kartı LED kartını çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın.
3. LED kartını avuç içi dayanağına sabitleyen tek (M2x3) vidayı çıkarın [1]. 4. LED kartını kaldırarak bilgisayardan çıkarın [2].
LED kartını takma Adimlar 1. LED kartını yerleştirin ve LED kartındaki vida deliklerini avuç içi dayanağındaki vida deliğiyle hizalayın [1]. 2. LED kartını avuç içi dayanağına sabitlemek için (M2x3) vidayı yerine takın [2].
3. LED kartı kablosunu sistem kartındaki konnektöre takın ve LED kartı kablosunu yönlendirin [1, 2].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Hoparlörler Hoparlörleri çıkarma Önkosullar 1. 2. 3. 4. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Adimlar 1. Hoparlör kablosunu sistem kartındaki konnektörden ayırın [1]. 2. Yapışkan bantları sökün ve hoparlör kablosunu yolundan ayırın [2, 3].
Hoparlörleri takma Adimlar 1. Hizalama direklerini ve lastik rondelaları kullanarak hoparlörleri avuç içi dayanağındaki yuvalara yerleştirin. 2. Hoparlör kablosunu yönlendirme kılavuzlarından geçirin.
3. Hoparlör kablosunu avuç içi dayanağına sabitlemek için yapışkan bandı yapıştırın [1]. 4. Hoparlör kablosunu sistem kartındaki konnektöre bağlayın [2, 3].
Sonraki Adimlar 1. 2. 3. 4. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Isı emici aksamı Isı emici aksamını çıkarma Önkosullar 1. 2. 3. 4. 5. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. microSD kartını çıkarın. Alt kapağı çıkarın. Pili çıkarın. İç çerçeveyi çıkarın. Adimlar 1. Sistem fanı kablosunu sistem kartındaki konnektörden ayırın.
2. Isı emici aksamını sistem kartına sabitleyen altı (M2x3) vidayı sökün [1]. NOT Vidaları ısı emici üzerinde gösterilen numaralara [1, 2, 3, 4, 5, 6) göre sökün. 3. Isı emicinin fan bölümünü sistem kartına sabitleyen iki (M2x3) vidayı sökün ve ısı emici aksamını [2] kaldırın.
Isı emici aksamını takma Adimlar 1. Isı emiciyi sistem kartının üzerine yerleştirin ve ısı emicideki vida deliklerini sistem kartındaki vida delikleriyle hizalayın [1]. 2. Isı emici aksamının fan bölümünü sistem kartına sabitleyen iki (M2x3) vidayı yerine takın. 3. Sırayla (ısı emicide belirtildiği şekilde), ısı emici aksamını sistem kartına [2] sabitleyen altı (M2x3) vidayı sıkın.
4. Sistem kartındaki konektörden gelen sistem fan kablosunu bağlayın.
Sonraki Adimlar 1. 2. 3. 4. 5. İç çerçeveyi yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Sistem kartı Sistem kartını çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. microSD kartını çıkarın. Alt kapağı çıkarın. Pili çıkarın. Bellek modülünü çıkarın. WLAN kartını çıkarın. Düğme pili çıkarın. DC girişini çıkarın. M.
Adimlar 1. Mandalı kaldırın ve aşağıdaki kabloları sistem kartından çıkarın: a) b) c) d) Hoparlör kablosu [1]. LED kartı kablosu [2]. USH FFC [3]. Dokunmatik yüzey FFC [4]. 2. Parmak izi destek braketini sistem kartına sabitleyen tek (M2x3) vidayı çıkarın [1]. 3. Parmak izi destek braketini bilgisayardan kaldırın [2]. 4. Parmak izi bağlantı noktasının bağlantısını kesin [3].
5. Sistem kartına [1] bağlı eDP kablosundaki yapışkan bandı çıkarın. 6. eDP desteğini sistem kartına sabitleyen iki M2x3 vidayı çıkarın [2]. 7. eDP braketini bilgisayardan çıkarın [3]. 8. Mandalı kaldırın ve eDP kablosunu sistem kartındaki konnektörden ayırın [4]. 9. Kablonun sistem panelindeki [5] konektör ile bağlantısını kesin.
10. Sistem kartını bilgisayara sabitleyen iki (M2x3) vidayı sökün [1]. 11. Sistem kartını kaldırarak bilgisayardan çıkarın [2].
Sistem kartını takma Adimlar 1. Sistem kartını avuç içi dayanağına hizalayıp yerleştirin [1]. 2. Sistem kartını avuç içi dayanağına sabitleyen iki (M2x3) vidayı yerine takın [2].
3. Kabloyu sistem kartındaki konektöre bağlayın [1]. 4. eDP kablosunu sistem kartındaki konektöre bağlayın [2]. 5. eDP destek braketini eDP konektörünün üstüne yerleştirin [3]. 6. eDP braketini sistem kartına sabitleyen iki (M2x3) vidayı yerine takın [4]. 7. Sistem kartına [5] bağlı eDP kablosundaki yapışkan bandı yapıştırın.
8. Parmak izi okuyucusunun kablosunu sistem panelindeki konnektöre bağlayın [1]. 9. Parmak izi destek braketini yerleştirin [2]. 10. Parmak izi okuyucusu destek braketini sistem kartına sabitlemek için tek (M2x3) vidayı yerine takın [3].
11. Aşağıdaki kabloları sistem kartına bağlayın. a) b) c) d) 72 Hoparlör kablosu [1]. LED kartı kablosu [2]. USH FFC’si [3] Dokunmatik Yüzey FFC'si [4].
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Isı emici aksamını yerine takın. M.2 SSD'yi yerine takın. DC girişini yerine takın. Düğme pili yerine takın. WLAN kartını yerine takın. Bellek modülünü yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Klavye Klavyeyi çıkarma Önkosullar 1. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. 2. MicroSD kartı çıkarın. 3.
4. 5. 6. 7. 8. 9. Pili çıkarın. Hoparlörü çıkarın. Bellek modülünü çıkarın. DC girişini çıkarın. WLAN kartını çıkarın. Sistem kartını çıkarın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı çıkarılabilir. 10. Düğme pili çıkarın. Adimlar 1. Mandalı kaldırın ve arkadan aydınlatma kablosu ile klavye kablosunu dokunmatik yüzeydeki konnektörlerden ayırın. 2. Klavyeyi avuç içi dayanağına sabitleyen 18 (M2x2.5) vidayı sökün [1]. 3.
Klavyeyi takma Adimlar 1. Klavyeyi hizalayıp avuç içi dayanağına yerleştirin [1]. 2. Klavyeyi avuç içi dayanağına sabitleyen 18 (M2x2.5) vidayı yerine takın [2].
3. Arkadan aydınlatma ve klavye kablosunu dokunmatik yüzeydeki konnektörlere bağlayın.
Sonraki Adimlar 1. Düğme pili yerine takın. 2. Sistem kartını yerine takın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı yerine takılabilir. 3. 4. 5. 6. 7. 8. 9. 10. WLAN kartını yerine takın. DC girişini yerine takın. Bellek modülünü yerine takın. Hoparlörü yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Klavye bağlantı aparatı Klavye braketini çıkarma Önkosullar 1. 2. 3. 4. 5. 6.
7. DC girişini çıkarın. 8. WLAN kartını çıkarın. 9. Sistem kartını çıkarın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı çıkarılabilir. 10. Düğme pili çıkarın. 11. Klavyeyi çıkarın. Adimlar 1. Klavyeyi klavye braketine sabitleyen altı (M2x2) vidayı çıkarın [1]. 2. Klavyeyi klavye braketinden çıkarın [2]. Klavye braketini takma Adimlar 1. Klavyeyi hizalayıp klavye braketine yerleştirin [1]. 2. Klavyeyi klavye braketine sabitleyen altı (M2x2) vidayı yerine takın [2].
Sonraki Adimlar 1. Klavyeyi yerine takın. 2. Düğme pili yerine takın. 3. Sistem kartını yerine takın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı yerine takılabilir. 4. 5. 6. 7. 8. 9. 10. 11. WLAN kartını yerine takın. DC girişini yerine takın. Bellek modülünü yerine takın. Hoparlörü yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın.
4. 5. 6. 7. 8. 9. Pili çıkarın. Hoparlörü çıkarın. Bellek modülünü çıkarın. DC girişini çıkarın. WLAN kartını çıkarın. Sistem kartını çıkarın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı çıkarılabilir. 10. Düğme pili çıkarın. 11. Klavyeyi çıkarın. Adimlar 1. Parmak izi okuyuculu güç düğmesini avuç içi dayanağına sabitleyen iki (M2x3) vidayı çıkarın [1]. 2. Parmak izi okuyucu kartlı güç düğmesini kaldırarak avuç içi dayanağından çıkarın [2]. Parmak izi okuyuculu güç düğmesini takma Adimlar 1.
Sonraki Adimlar 1. Klavyeyi yerine takın. 2. Düğme pili yerine takın. 3. Sistem kartını yerine takın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı yerine takılabilir. 4. 5. 6. 7. 8. 9. 10. 11. WLAN kartını yerine takın. DC girişini yerine takın. Bellek modülünü yerine takın. Hoparlörü yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran aksamı Ekran aksamını çıkarma Önkosullar 1. 2.
Adimlar 1. Kablosuz anteni, sistem kartındaki yönlendirme kılavuzlarından çıkarın [1]. 2. EDP kablo braketini [2] sabitleyen bandı çıkarın. 3. eDP kablo braketini sistem kartına sabitleyen iki M2x3 vidayı çıkarın [3]. 4. eDP kablo braketini sistem kartından kaldırın [4]. 5. eDP kablosunun bağlantısını kesip kabloyu yolundan ayırın [5, 6]. 6. Ekran aksamını 180 derece olacak şekilde açın ve sistemi ters çevirip düz bir yüzeye koyun.
7. Ekran aksamını sistem kasasına [1] sabitleyen dört (M2.5x5) vidayı sökün. 8. Ekran aksamını sistemden çıkarın [2].
Ekran aksamını takma Bu görev ile ilgili NOT Ekran aksamını avuç içi dayanağına takmadan önce menteşelerin olabildiğince açıldığından emin olun. Adimlar 1. Sistem kasasını ekran aksamının menteşelerin altına hizalayıp yerleştirin [1]. 2. Ekran aksamını sistem kasasına [2] sabitleyen dört (M2.5x5) vidayı yerine takın.
3. Sistem kasasını ekran aksamına oturtun.
4. Kablosuz anteni, sistem kartındaki yönlendirme kılavuzlarından yeniden geçirin [1]. 5. Kabloyu sistem kartındaki konektöre bağlayın [2]. 6. eDP kablosunu sistem kartındaki eDP konektörüne bağlayın [3]. 7. eDP kablo braketini sistem kartına yerleştirin [4]. 8. eDP kablo braketini sistem kartına sabitleyen iki (M2x3) vidayı yerine takın [5]. 9. EDP kablo braketini sistem kartına [6] sabitleyen bandı yapıştırın.
Sonraki Adimlar 1. 2. 3. 4. 5. WLAN kartını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran çerçevesi Ekran çerçevesini çıkarma Önkosullar 1. 2. 3. 4. 5. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Ekran aksamını çıkarın.
Adimlar 1. NOT Ekran çerçevesi çıkarıldıktan sonra tekrar kullanılamaz. Ekran çerçevesinin alt kenarında bulunan sol ve sağ menteşelerin yanındaki girintileri plastik bir çubukla dikkatli bir şekilde kanırtarak açın [1]. 2. DİKKAT Ekran çerçevesini kaldırarak açarken, ekran çerçevesin dış kenarından ellerinizi veya plastik çubuklar kullanarak kaldırdığınızdan emin olun; tornavida veya başka keskin nesneler kullanmak ekran kapağına zarar verebilir.
Ekran çerçevesini takma Adimlar Ekran çerçevesini ekran aksamıyla hizalayın, ardından yumuşak bir hareketle ekran çerçevesini yerine oturtun.
Sökme ve Takma
Sonraki Adimlar 1. 2. 3. 4. 5. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran paneli Ekran panelini çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. 8. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Ekran aksamını çıkarın. Ekran çerçevesini çıkarın. Menteşe başlıklarını çıkarın.
2. Ekran kablosu konnektöründeki iletken bandı [1] sökün. 3. Ekran kablosu konnektörünü sabitleyen yapışkan şeridi çıkarın [2]. 4. Mandalı kaldırın ve ekran kablosunu ekran panelindeki konnektörden ayırın[3, 4]. NOT Streç (SR) Bantları ekran panelinden çekmeyin ve serbest bırakmayın. Destekleri ekran panelinden ayırmaya gerek yoktur.
Sökme ve Takma 93
Ekran panelini takma Adimlar 1. Ekran kablosunu konnektöre takın ve mandalı kapatın [1, 2]. 2. Ekran kablosu konnektörünü sabitlemek için yapıştırıcı kordonu yapıştırın [3]. 3. Ekran kablosu konnektörünü sabitlemek için iletken bandı yapıştırın [4]. 4. NOT LCD Panel, önce içe takılması gereken iki (SOL+SAĞ) braketle gelir; ardından LCD panelin tabanında bulunan iki vidayı sıkın. Ekran panelini ekran aksamına sabitleyen iki (M2.5x3) vidayı yerine takın.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. 8. Ekran menteşelerini yerine takın. Menteşe başlıklarını yerine takın. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Kamera Kamerayı çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın.
8. Ekran menteşelerini çıkarın. 9. Ekran panelini çıkarın. Adimlar 1. Kamerayı yerine sabitleyen iki iletken bandı sökün [1]. 2. Kamera modülünü ekran arka kapağından dikkatli bir şekilde kaldırarak çıkarın [2]. 3. Kamera kablosunu kamera modülü üzerindeki konnektörden çıkarın [3]. Kamerayı takma Adimlar 1. Kamera kablosunu kamera modülündeki konnektöre takın [1]. 2. Kamerayı ekranın arka kapağındaki yuvaya takın [2]. 3. İki adet iletken bandı kameranın üzerine yapıştırın [3].
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. 8. 9. Ekran panelini yerine takın. Ekran menteşelerini yerine takın. Menteşe başlıklarını yerine takın. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Menteşe başlıkları Menteşe başlıklarını çıkarma Önkosullar 1. 2. 3. 4. 5. 6. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin.
Adimlar 1. Menteşe başlıklarını kasaya sabitleyen iki (M2x3) vidayı sökün [1]. 2. Menteşe başlıklarını sıkıştırarak başlıkları ekran arka kapağındaki kirişlerden serbest bırakın, ardından bunları içeri doğru kaydırarak başlıkları ekran menteşesinden çıkarın [2]. Menteşe başlıklarını takma Adimlar 1. Menteşe başlıklarını yerleştirin ve ekran menteşeleri üzerinde dışa doğru kaydırın [1]. 2. Menteşe başlıklarını ekran menteşesine sabitleyen iki (M2x3) vidayı yerine takın.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran menteşeleri Ekran menteşesini çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın. Ekran aksamını çıkarın. Ekran çerçevesini çıkarın.
Adimlar 1. Ekran menteşesini ekran aksamına sabitleyen dört (M2.5x3) vidayı sökün [1]. 2. Ekran menteşelerini ekranın arka kapağından çıkarın [2]. Ekran menteşesini takma Adimlar 1. Ekran menteşesini ekran aksamına yerleştirin. 2. Ekran menteşesini ekran aksamına sabitlemek için dört (M2.5x3) vidayı yerine takın.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. Menteşe başlıklarını yerine takın. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran (eDP) kablosu Ekran kablosunu çıkarma Önkosullar 1. 2. 3. 4. 5. 6. 7. 8. Bilgisayarınızın içinde çalışmadan önce bölümündeki prosedürü takip edin. MicroSD kartı çıkarın. Alt kapağı çıkarın. Pili çıkarın.
9. Ekran panelini çıkarın. 10. Kamerayı çıkarın. Adimlar İletken bandı sökün ve ekran kablosunu yolundan ayırıp yapışkan banttan kurtarın, ardından ekran kablosunu ekran arka kapağından kaldırarak çıkarın. Ekran kablosunu takma Adimlar 1. Ekran kablosunu ekran arka kapağına yapıştırın. 2. İletken bandı yapıştırıp ekran kablosunu ekran arka kapağından geçirin.
Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Kamerayı yerine takın. Ekran panelini yerine takın. Ekran menteşelerini yerine takın. Menteşe başlıklarını yerine takın. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın. Ekran arka kapağı aksamı Ekran arka kapağını yerine takma Önkosullar 1. 2. 3. 4. 5. 6. 7. 8. 9.
10. Kamerayı çıkarın. 11. Ekran kablosunu çıkarın. Bu görev ile ilgili Yukarıdaki adımları gerçekleştirdikten sonra, sıra ekran arka kapağına gelir. Sonraki Adimlar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Ekran kablosunu yerine takın. Kamerayı yerine takın. Ekran panelini yerine takın. Ekran menteşelerini yerine takın. Menteşe başlıklarını yerine takın. Ekran çerçevesini yerine takın. Ekran aksamını yerine takın. Pili yerine takın. Alt kapağı yerine takın. MicroSD kartı yerine takın.
3. 4. 5. 6. 7. 8. 9. Alt kapağı çıkarın. Pili çıkarın. Hoparlörü çıkarın. Bellek modülünü çıkarın. DC girişini çıkarın. WLAN kartını çıkarın. Sistem kartını çıkarın. NOT Isı emicisi aksamı takılı durumdayken sistem kartı çıkarılabilir. 10. Düğme pili çıkarın. 11. Klavyeyi çıkarın. 12. SmartCard okuyucuyu çıkarın. Bu görev ile ilgili Yukarıdaki adımları uyguladıktan sonra, geriye avuç içi dayanağı ve klavye aksamı kalır. Sonraki Adimlar 1. 2. 3. 4. SmartCard okuyucuyu yerine takın. Klavyeyi yerine takın.
11. MicroSD kartı yerine takın. 12. Bilgisayarınızın içinde çalıştıktan sonra bölümündeki prosedürü uygulayın.
5 Sorun Giderme Gelişmiş Yükleme Öncesi Sistem Değerlendirmesi (ePSA) tanılamaları Bu görev ile ilgili ePSA tanılamaları (sistem tanılamaları olarak da bilinir) donanımınızın tam bir kontrolünü gerçekleştirir. ePSA, BIOS ile tümleşiktir ve BIOS tarafından dahili olarak başlatılır.
Örneğin, belli bir aradan sonra güç ve pil durum ışığı sarı renkte iki kez belli bir aradan sonra yanıp söner, ve ardından belli bir aradan sonra beyaz renkte üç kez yanıp söner. Bu 2,3 modeli, bilgisayar belleğin veya RAM'ın tespit edilmediğini gösterecek şekilde kapanana kadar devam eder. Aşağıdaki tablo, farklı güç ve pil durum ışığı modellerini ve ilgili sorunları göstermektedir. Tablo 3.
6 Yardım alma Konular: • Dell'e Başvurma Dell'e Başvurma Önkosullar NOT Etkin bir Internet bağlantınız yoksa, başvuru bilgilerini satış faturanızda, irsaliyede, fişte veya Dell ürün kataloğunda bulabilirsiniz. Bu görev ile ilgili Dell birden fazla çevrimiçi ve telefon tabanlı destek ve servis seçeneği sunar. Kullanılabilirlik ülkeye ve ürüne göre değişir ve bazı hizmetler bulunduğunuz bölgede olmayabilir. Satış, teknik destek veya müşteri hizmetleri ile ilgili konularda Dell'e başvurmak için: Adimlar 1.