Dell Latitude 5400 Servicehandbok Regulatory Model: P98G Regulatory Type: P98G001 February 2021 Rev.
Anmärkningar, försiktighetsbeaktanden och varningar OBS: OBS innehåller viktig information som hjälper dig att få ut det mesta av produkten. CAUTION: VIKTIGT anger antingen risk för skada på maskinvara eller förlust av data och förklarar hur du kan undvika problemet. VARNING: En VARNING visar på en potentiell risk för egendoms-, personskador eller dödsfall. © 2019 -2020 Dell Inc. eller dess dotterbolag. Med ensamrätt. Dell, EMC och andra varumärken är varumärken som tillhör Dell Inc.
Contents Chapter 1: Arbeta med datorn........................................................................................................6 Säkerhetsinstruktioner....................................................................................................................................................... 6 Innan du arbetar inuti datorn...................................................................................................................................... 6 Säkerhetsföreskrifter......
Ta bort M.2 SSD.......................................................................................................................................................... 42 Installera M.2-SSD-kortet......................................................................................................................................... 43 Halvledarenhetsfäste-hållare..........................................................................................................................................
Bildskärmsgångjärnen..................................................................................................................................................... 106 Ta bort bildskärmsgångjärn..................................................................................................................................... 106 Installera bildskärmsgångjärn..................................................................................................................................
1 Arbeta med datorn Ämnen: • Säkerhetsinstruktioner Säkerhetsinstruktioner Förutsättningar Följ dessa säkerhetsföreskrifter för att skydda datorn och dig själv. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: ● Du har läst säkerhetsinformationen som medföljde datorn. ● En komponent kan ersättas eller – om du köper den separat – monteras i omvänd ordning jämfört med borttagningsproceduren.
2. Se till att arbetsytan är ren och plan så att inte datorkåpan skadas. 3. Stäng av datorn. 4. Koppla bort alla externa kablar från datorn. CAUTION: Nätverkskablar kopplas först loss från datorn och sedan från nätverksenheten. 5. Koppla bort datorn och alla anslutna enheter från eluttagen. 6. Tryck och håll ned strömbrytaren när datorn är urkopplad så att moderkortet jordas. OBS: Undvik elektrostatiska urladdningar genom att jorda dig själv.
● Tillfälliga – tillfälliga fel representerar cirka 80 procent av de ESD-relaterade felen. Den höga andelen tillfälliga fel innebär att de flesta gånger som skador uppstår kan de inte identifieras omedelbart. DIMM-minnet utsätts för en statisk stöt, men spårningen försvagas knappt och ger inte omedelbart några symtom utåt som är relaterade till skadan.
● Transport av känsliga komponenter - När du transporterar ESD-känsliga komponenter, såsom reservdelar eller delar som ska returneras till Dell, är det viktigt att placera dessa artiklar i antistatiska påsar för säker transport. Sammanfattning av ESD-skydd Vi rekommenderar att alla servicetekniker använder traditionella trådbundna ESD-jordade handledsremmar och en skyddande antistatisk matta hela tiden när de servar Dell-produkter.
2 Teknik och komponenter I det här kapitlet beskrivs teknik och komponenter som finns i systemet. Ämnen: • • • • USB-funktioner USB Typ-C HDMI 1.4a Strömbrytare LED-beteende USB-funktioner USB (Universal Serial Bus) lanserades 1996. Det förenklade drastiskt anslutningen mellan värddatorer och kringutrustning, till exempel möss, tangentbord, externa drivrutiner och skrivare. Låt oss med hjälp av nedanstående tabell ta en snabb titt på hur USB har utvecklats. Tabell 1.
USB 3.0/USB 3.1 Gen 1 ger en mycket högre prestanda tack vare följande tekniska förändringar: ● En ytterligare fysisk buss har lagts till parallellt med den befintliga USB 2.0-bussen (se bilden nedan). ● USB 2.0 hade tidigare fyra ledningar (ström, jord och ett ledningspar för differentiella data). Med USB 3.0/USB 3.1 Gen 1 tillkommer ytterligare fyra, vilket ger två par för differentialsignaler (för mottagning och sändning) för en kombination av totalt åtta anslutningar i kontakter och kablar. ● USB 3.
USB Typ-C USB typ C är en ny, liten fysisk kontakt. Kontakten kan ge stöd för olika spännande nya USB-standarder, till exempel USB 3.1 och USB power delivery (USB PD). Alternativt läge USB typ C är en ny kontaktstandard som är väldigt liten. Den är omkring en tredje av storleken på en gammal USB typ A-kontakt. Det här är en enkel kontaktstandard som varje enhet ska kunna använda.
Thunderbolt 3 via typ-C-USB Thunderbolt 3 innebär Thunderbolt via USB typ C med hastigheter upp till 40 Gbit/s, och skapandet av en kompakt port som gör allt - och levererar den snabbaste, mest mångsidiga anslutningen till alla dockor, bildskärmar eller dataenheter, t.ex. en extern hårddisk. Thunderbolt 3 använder USB typ C- kontakt/port för anslutning till kringutrustning som stöds. 1. 2. 3. 4.
● HDMI Micro-kontakt – En ny, mindre kontakt för mobiltelefoner och andra bärbara enheter som hanterar videoupplösningar på upp till 1080 p ● Automotive Connection System – Nya kablar och kontakter för fordonsvideosystem, utformade för att uppfylla de unika kraven som fordonsmiljön ställer samtidigt som de ger äkta HD-kvalitet Fördelar med HDMI: ● HDMI med hög kvalitet överför okomprimerat digitalt ljud och video för den bästa och skarpaste bildkvaliteten ● HDMI till låg kostnad ger kvaliteten och funktion
Strömbrytare med fingeravtrycksläsare kommer inte att ha någon LED och kommer att utnyttja de lediga LED i systemet för att visa systemstatusen ● Nätadapter LED: ○ LED på nätadaptern lyser vit när strömmen levereras från eluttaget. ● Batteriindikator LED: ○ När datorn är ansluten till ett eluttag har batterilampan följande funktion: 1. Fast vitt sken- batteriet laddas. När laddningen är färdig släcks LED. ○ Om datorn körs på ett batteri fungerar batterilampan enligt följande: 1.
3 Huvudkomponenter i systemet 1. Kåpan 2.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. DC-in-port Systemfläkt Moderkort Batteri Inre ramen Högtalare smartkortläsaren Pekplatta strömbrytarkort LED-kort Handledsstöd Bildskärmsenhet Halvledarenhet Minnesmodulen WLAN-kort Knappcellsbatteri OBS: Dell innehåller en lista över komponenter och tillhörande artikelnummer för den ursprungliga systemkonfigurationen som köpts. Dessa delar är tillgängliga enligt garantitäckningar som kunden har köpt.
4 Isärtagning och ihopsättning Ämnen: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • MicroSD-kort Kåpan Batteriet WWAN-kortet WLAN-kort Knappcellsbatteri Minnesmoduler DC-in-port SSD Halvledarenhetsfäste-hållare Inre ramen smartkortläsaren Pekskivans knappar LED-kort Högtalare Kylflänsmonteringen Moderkort Tangentbord Tangentbordsfäste Strömbrytare Bildskärmsenhet Bildskärmsram Bildskärmspanelen Kamera Gångjärnskåpor Bildskärmsgångjärnen Bildskärmens (EDP)-kabel Bildskärmens bakre höljesmonterin
Installerar microSD-kortet Steg 1. Justera microSD-kortet i dess kortplats på datorn [1]. 2. Skjut in microSD-kortet i kortplatsen tills det klickar på plats [2].
3. Följ anvisningarna i När du har arbetat inuti datorn. Kåpan Ta bort kåpan Förutsättningar 1. Följ anvisningarna i innan du arbetar inuti datorn. 2. Ta bort microSD kort. Steg 1. Lossa de åtta fästskruvarna [1].
2. Använd en plastrits [1] genom att fälla upp baslocket från det övre vänstra hörnet och fortsätt att arbeta på sidorna för att öppna baslocket [2].
3. Lyft och ta bort kåpan från datorn.
Installera kåpan Steg 1. Justera och placera kåpan på datorn.
2.
3. Dra åt de åtta fästskruvarna som håller fast kåpan i datorn.
Nästa Steg 1. Sätt tillbaka microSD-kortet. 2. Följ proceduren i när du har arbetat inuti datorn. Batteriet Försiktighetsåtgärder gällande litiumjonbatterier CAUTION: ● Var försiktig när du hanterar litiumjonbatterier. ● Ladda ur batteriet så mycket som möjligt innan du tar bort det från datorn. Detta kan göras genom att koppla bort nätadaptern från systemet för att låta batteriet laddas ur. ● Undvik att krossa, tappa, skada eller tränga in i batteriet med främmande föremål.
Ta bort batteriet Förutsättningar 1. Följ anvisningarna i innan du arbetar inuti datorn. 2. Ta bort microSD kort. 3. Ta bort kåpan. Steg 1. Koppla loss batterikabeln från kontakten på moderkortet. 2. Lossa den enda fästskruven som håller fast batteriet i handledsstödet [1]. 3. Skjut in batteriet inåt och lyft batteriet bort från handledsstödet [2].
Installera batteriet Steg 1. Justera och skjut batteriet på handledsstödet [1]. 2. Dra åt den enda fästskruven som håller fast batteriet på handledsstödet [2].
3. Anslut batterikabeln till kontakten på moderkortet.
Nästa Steg 1. Sätt tillbaka kåpan. 2. Sätt tillbaka microSD-kortet. 3. Följ proceduren i när du har arbetat inuti datorn. WWAN-kortet Ta bort WWAN-kortet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD-kortet. Ta bort baskåpan. Ta bort batteriet. Steg 1. Ta bort den enda skruven (M2x3) som håller fast WWAN-kortet i moderkortet [1]. 2. Ta bort WWAN-kortfästet som håller fast WWAN-antennkablarna [2]. 3.
Installera WWAN-kortet Om denna uppgift CAUTION: Undvik att skada WWAN-kortet genom att se till att inte några kablar placeras under kortet. Steg 1. Sätt i WWAN-kortet i kontakten på moderkortet [1]. 2. Anslut WWAN-antennkablarna till kontakterna på WWAN-kortet[2]. 3. Sätt i WWAN-kortfästet för att fästa WWAN-kablarna till WWAN-kortet [3]. 4. Sätt tillbaka den enda skruven (M2x3) som håller fast WWAN-kortfästet i WWAN-kortet [4].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. WLAN-kort Ta bort WLAN-kortet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Ta bort den enda (M2x3) skruven som håller fast WLAN-kortets fäste i moderkortet [1]. 2. Ta bort WLAN-kortfästet som håller fast WLAN-antennkablarna [2]. 3.
Installera WLAN-kortet Om denna uppgift CAUTION: Undvik att skada WLAN-kortet genom att se till att inte några kablar placeras under kortet. Steg 1. Sätt i WLAN-kortet i kontakten på moderkortet [1]. 2. Anslut WLAN-antennkablarna till kontakterna på WLAN-kortet[2]. 3. Sätt i WLAN-kortfästet för att fästa WLAN-kablarna till WLAN-kortet [3]. 4. Sätt tillbaka den enda skruven (M2x3) som håller fast WLAN-kortfästet i WLAN-kortet [4].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Knappcellsbatteri Ta bort knappcellsbatteriet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Koppla ur knappcellsbatteriets kabel från kontakten på moderkortet [1]. 2. Lyft bort knappcellsbatteriet från moderkortet [2].
Installera knappcellsbatteriet Steg 1. Placera knappcellsbatteriet på moderkortet [1]. 2. Anslut knappcellsbatteriets kabel till kontakten på moderkortet [2].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Minnesmoduler Ta bort minnesmodulen Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Bänd i kvarhållningsklämmorna som håller fast minnesmodulen tills minnesmodulen hoppar upp [1]. 2. Ta bort minnesmodulen från minnesmodulkortplatsen [2].
Installera minnesmodulen Steg 1. Rikta in skåran på minnesmodulen med fliken på minnesmodulplatsen. 2. För in minnesmodulen ordentligt i facket i en vinkel [1]. 3. Tryck sedan minnesmodulen nedåt tills klämmorna håller fast den [2]. OBS: Om du inte hör något klick tar du bort minnesmodulen och försöker igen.
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. DC-in-port Tar bort DC-in port Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Ta bort de två (M2x5) som sätter fast-typ C-fästet på moderkortet [1]. 2. Lyft bort typ-C fästet från datorn [2].
3. Koppla ur DC-in portkabeln från kontakten på moderkortet och ta bort DC-in porten från datorn [1, 2].
Installerar DC-in porten Steg 1. Placera DC-in porten i dess kortplats på datorn [1]. 2. Anslut DC-in portkabeln till kontakten på moderkortet [2].
3. Placera typ-C fästet i dess kortplats på datorn [1]. 4. Byt ut de två (M2x5) för att fästa typ-C fästet på handledsstödet [2].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. SSD Ta bort M.2 SSD Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Ta bort de två skruvarna (M2x3) som håller fast M.2 SSD supportfästet på handledsstödet [1]. 2. Vrid försiktigt och ta bort SSD-stödfästet från M.2 SSD-kortplatsen [2].
3. Ta bort SSD på SSD-värmeplattan. Installera M.2-SSD-kortet Steg 1. Placera M.2 SSD-kortet i kortplatsen på handledsstödet [1]. 2. Justera och placera SSD-stödfästet ovanför M.2 SSD-kortet [2]. 3. Sätt tillbaka de två skruvarna (M2x3) för att fästa SSD-stödfästet på handledsstödet [3].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Halvledarenhetsfäste-hållare Ta bort halvledarenhetsfästet Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD-kortet. Ta bort kåpan. Ta bort batteriet. Ta bort M.2 SSD. Steg 1. Ta bort den enda (M2x3) skruven som håller fast fästet på handledsstödet [1]. 2.
Installera halvledarenhetsfästet Steg 1. Justera fästet och sätt in den i spåret på handledsstödet [1]. 2. Sätt tillbaka den enda (M2x3) skruven för att fästa fästet på handledsstödet [2].
Nästa Steg 1. 2. 3. 4. 5. Sätt tillbaka M.2 SSD. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Inre ramen Ta bort den inre ramen Förutsättningar 1. 2. 3. 4. 5. 6. 7. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort WLAN-kortet. Ta bort M.2 SSD. Ta bort M.2 SSD fästet. Steg 1. Trä av WLAN-antennkablarna.
2. Ta bort de fem (M2x5) skruvarna som håller fast den inre ramen på moderkortet [1]. 3. Ta bort de sex (M2x3) skruvarna som håller fast den inre ramen i systemets chassi [2]. 4. Lyft den inre ramen bort från systemets chassi [3].
Installering av inre ramen Steg 1. Justera och placera den inre ramen på systemets chassi [1]. 2. Sätt tillbaka de sex (M2x3) skruvarna som håller fast den inre ramen i systemets chassi [2]. 3. Sätt tillbaka de fem (M2x5) skruvarna som håller fast den inre ramen på moderkortet [3].
4. Dra om WLAN-antennkablarna.
Nästa Steg 1. 2. 3. 4. 5. 6. 7. Sätt tillbaka M.2 SSD-hållare. Sätt tillbaka M.2 SSD. Sätt tillbaka WLAN-kortet. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. smartkortläsaren Ta bort SmartCard-läsararen Förutsättningar 1. 2. 3. 4. 5. 6. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD-kortet. Ta bort kåpan. Ta bort batteriet. Ta bort WLAN-kortet. Ta bort den inre ramen. Steg 1.
3. Ta bort de tre (M2x3) skruvar som håller fast smartcard-läsaren på handledsstödet [1]. 4. Lyft smartcard läsarkortet bort från handledsstödet [2].
Installera SmartCard-läsararen Steg 1. Placera smartcard-läsarkortet på handledsstödet [1]. 2. Sätt tillbaka de tre (M2x3) skruvar som håller fast smartcard-läsaren på handledsstödet [2].
3. Anslut SmartCard-läsare FFC till kontakten på USH-kortet [1] 4. Sätt smartcard FFC i handledsstödet [2].
Nästa Steg 1. 2. 3. 4. 5. 6. Sätt tillbaka den inre ramen. Sätt tillbaka WLAN-kortet. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Pekskivans knappar Ta bort pekplattans tangentbord Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort högtalaren. Steg 1.
3. Öppna spärren och koppla bort pekplattans kabel från kontakten på pekplattan [1, 2].
4. Ta bort de två skruvarna (M2x3) som håller fast pekplattan på fästet på handledsstödet [1]. 5. Lyft bort pekplattans fäste bort från datorn [2].
Installera pekplattans tangentbord Steg 1. Placera pekplattans tangentbord i spåret på handledsstödet [1]. 2. Sätt tillbaka de två skruvarna (M2x3) för att fästa pekplattans tangentbord på handledsstödet [2].
3. Anslut pekplattans tangentbord till kontakten på pekplattan [1, 2].
4. Anslut SmartCard Reader Flexible Flat Cable (FFC) till USH-kortet [1]. 5. Fäst FFC på handledsstödet [2].
Nästa Steg 1. 2. 3. 4. 5. Sätt tillbaka högtalaren. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. LED-kort Ta bort LED-kortet Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Koppla ur kabeln för LED-kortet från kontakten på moderkortet [1]. 2. Koppla bort LED-kortets kabel [2].
3. Ta bort den enda (M2x3) skruven för att fästa LED-kortet i handledsstödet [1]. 4. Lyft bort LED-kortet från datorn [2].
Installera LED-kortet Steg 1. Placera LED-kortet och justera skruvhålet på LED-kortet med skruvhålet på handledsstödet [1]. 2. Sätt tillbaka den enda (M2x3) skruven för att fästa LED-kortet i handledsstödet [2].
3. Anslut LED-kortets kabel till kontakten på moderkortet och dra LED-kortets kabel [1, 2].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Högtalare Ta bort högtalarna Förutsättningar 1. 2. 3. 4. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Steg 1. Koppla loss högtalarkabeln från kontakten på moderkortet [1]. 2. Dra av tejpen och ta bort högtalarkabeln [2, 3].
3. Lyft och ta bort högtalarna från handledsstödet.
Installera högtalarna Steg 1. Använd justeringstapparna och gummitågringarna för att placera högtalarna i facken på handledsstödet. 2. Dra högtalarkabeln genom kabelhållarna.
3. Sätt dit tejpen för att fästa högtalarkabeln på handledsstödet [1]. 4. Anslut högtalarkabeln till kontakten på moderkortet [2, 3].
Nästa Steg 1. 2. 3. 4. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Kylflänsmonteringen Tar bort kylflänsmonteringen Förutsättningar 1. 2. 3. 4. 5. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD-kortet. Ta bort kåpan. Ta bort batteriet. Ta bort den inre ramen. Steg 1. Koppla bort systemfläktkabeln från kontakten på moderkortet.
2. Ta bort de sex skruvarna (M2x3) som håller fast kylflänsmonteringen i moderkortet [1]. OBS: Ta bort skruvarna i samma ordning som på bildtext nummer [1, 2, 3, 4, 5, 6] som anges på kylflänsen. 3. Ta bort de två skruvarna (M2x3) som håller fast fläkten på kylflänsmonteringen till moderkortet och lyft kylflänsmonteringen [2].
Installera kylflänsmonteringen Steg 1. Placera kylflänsmonteringen på moderkortet och rikta in skruvhålen på kylflänsen med skruvhålen på moderkortet [1]. 2. Byt ut de två skruvarna (M2x3) som håller fast fläktdelen på kylflänsmonteringen på moderkortet. 3. Dra i rätt ordning (så som anges på kylflänsen), åt de sex skruvarna(M2x3) som håller fast kylflänsen till moderkortet [2].
4. Anslut systemfläktkabeln från kontakten på moderkortet.
Nästa Steg 1. 2. 3. 4. 5. Sätt tillbaka den inre ramen. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Moderkort Ta bort moderkortet Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 72 Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort minnesmodulen. Ta bort WLAN-kortet. Ta bort knappcellsbatteriet. Ta bort DC-in . Ta bort M.2 SSD . Ta bort kylflänsmonteringen.
Steg 1. Lyft haken och koppla bort följande kablar från moderkortet. a. b. c. d. Högtalarkabel [1] LED-kortkabel [2]. USH FFC [3]. Pekplatta FFC [4]. 2. Ta bort den enkla (M2x3) skruven som håller fast stödfäste för fingeravtrycksläsaren på moderkortet [1]. 3. Lyft fingeravtrycksläsaren stödfäste bort från datorn [2]. 4. Koppla bort porten för fingeravtrycksläsaren [3].
5. Dra av tejpen på eDP-kabeln som är ansluten till moderkortet [1]. 6. Ta bort de två (M2x3) skruvarna som säkrar eDP-hållaren på moderkortet [2]. 7. Ta bort eDP-fästet bort från [3]. 8. Lyft bort eDP-kabeln från kontakten på moderkortet [4]. 9. Koppla loss kabeln från kontakten på moderkortet [5].
10. Ta bort de två (M2x3) skruvarna för att fästa moderkortet på handledsstödet [1]. 11. Lyft bort moderkortet från datorn [2].
Installera moderkortet Steg 1. Justera och placera systemkortet på handledsstödet [1]. 2. Sätt tillbaka de två (M2x3) skruvarna för att fästa moderkortet på handledsstödet [2].
3. Anslut-kabeln till kontakten på moderkortet [1]. 4. Anslut eDP-kabeln till kontakten på moderkortet [2]. 5. Placera eDP-supportfästet ovanför eDP-kontakten [3]. 6. Sätt tillbaka de två (M2x3) skruvarna som säkrar eDP-kabelhållaren på moderkortet [4]. 7. Sätt fast tejpen på eDP-kabeln som är ansluten till moderkortet [5].
8. Anslut fingeravtrycksläsarkabeln till kontakten på moderkortet [1]. 9. Sätt dit fingeravtrycksläsarens supportfäste [2]. 10. Byt ut den enda (M2x3) skruven för att fästa stödfästet för fingeravtrycksläsaren på moderkortet [3].
11. Anslut följande kablar till moderkortet: a. b. c. d. Högtalarkabel [1] LED-kortets kabel [2] USH FFC [3] Pekplatta FFC [4].
Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Sätt tillbaka kylflänsmonteringen. Sätt tillbaka M.2 SSD. Sätt tillbaka DC-in. Sätt tillbaka knappcellsbatteriet Sätt tillbaka WLAN-kortet. Sätt tillbaka minnesmodulen. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Tangentbord Ta bort tangentbordet Förutsättningar 1. Följ anvisningarna i innan du arbetar inuti datorn. 2. Ta bort microSD kort. 3. Ta bort kåpan.
4. 5. 6. 7. 8. 9. Ta Ta Ta Ta Ta Ta bort bort bort bort bort bort batteriet. högtalaren. minnesmodulen. DC-in . WLAN-kortet. moderkortet. OBS: Systemkortet kan tas bort med kylfläns enhet fastsatt. 10. Ta bort knappcellsbatteriet. Steg 1. Lyft haken och koppla ur bakgrundsljuskabeln och tangentbordskablarna från kontakterna på pekplattan. 2. Ta bort 18 (M2x2.5) skruvarna som håller tangentbordet i handledsstödet [1]. 3.
Installera tangentbordet Steg 1. Justera och placera tangentbordet på handledsstödet [1]. 2. Byt ut de 18 (M2x2.5) skruvarna som håller tangentbordet i handledsstödet [2].
3. Anslut den bakgrundsbelysta kabeln och tangentbordskablarna till kontakterna på pekplattan.
Nästa Steg 1. Sätt tillbaka knappcellsbatteriet 2. Sätt tillbaka moderkortet. OBS: Systemkortet kan bytas ut med kylflänsen enhet fastsatt. 3. 4. 5. 6. 7. 8. 9. 10. Sätt tillbaka WLAN-kortet. Sätt tillbaka DC-in. Sätt tillbaka minnesmodulen. Sätt tillbaka högtalaren. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Tangentbordsfäste Ta bort tangentbordsfästet Förutsättningar 1. 2. 3. 4. 5. 6.
7. Ta bort DC-in . 8. Ta bort WLAN-kortet. 9. Ta bort moderkortet. OBS: Systemkortet kan tas bort med kylfläns enhet fastsatt. 10. Ta bort knappcellsbatteriet 11. Ta bort tangentbordet. Steg 1. Ta bort de sex (M2x2) skruvarna som håller fast tangentbordet på tangentbordsfästet [1]. 2. Ta bort tangentbordet från tangentbordsfästet [2]. Installera tangentbordsfästet Steg 1. Rikta in och placera tangentbordet på tangentbordets fäste [1]. 2.
Nästa Steg 1. Sätt tillbaka tangentbordet. 2. Sätt tillbaka knappcellsbatteriet 3. Sätt tillbaka moderkortet. OBS: Systemkortet kan bytas ut med kylflänsen enhet fastsatt. 4. 5. 6. 7. 8. 9. 10. 11. Sätt tillbaka WLAN-kortet. Sätt tillbaka DC-in. Sätt tillbaka minnesmodulen. Sätt tillbaka högtalaren. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Strömbrytare Ta bort strömbrytaren med med fingeravtrycksläsare Förutsättningar 1.
4. 5. 6. 7. 8. 9. Ta Ta Ta Ta Ta Ta bort bort bort bort bort bort batteriet. högtalaren. minnesmodulen. DC-in . WLAN-kortet. moderkortet. OBS: Systemkortet kan tas bort med kylfläns enhet fastsatt. 10. Ta bort knappcellsbatteriet. 11. Ta bort tangentbordet. Steg 1. Ta bort de två (M2x3) som säkrar strömbrytaren med fingeravtrycksläsare på handledsstödet [1]. 2. Lyft strömbrytaren med fingeravtrycksläsare från handledsstödet [2]. Installera strömbrytaren med med fingeravtrycksläsare Steg 1.
Nästa Steg 1. Sätt tillbaka tangentbordet. 2. Sätt tillbaka knappcellsbatteriet 3. Sätt tillbaka moderkortet. OBS: Systemkortet kan bytas ut med kylflänsen enhet fastsatt. 4. 5. 6. 7. 8. 9. 10. 11. Sätt tillbaka WLAN-kortet. Sätt tillbaka DC-in. Sätt tillbaka minnesmodulen. Sätt tillbaka högtalaren. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Bildskärmsenhet Ta bort bildskärmsenheten Förutsättningar 1. 2. 3. 4. 5.
Steg 1. Ta bort den trådlösa antennen från routingstyrningarna på moderkortet [1]. 2. Dra av tejpen som säkrar eDP-kabelhållaren [2]. 3. Ta bort de två (M2x3) skruvarna som säkrar eDP-kabelhållaren på moderkortet [3]. 4. Lyft eDP-kabelfästet från moderkortet [4]. 5. Koppla ur och ta bort eDP-kabeln [5, 6]. 6. Öppna bildskärmsmonteringen till en 180 graders vinkel och vänd över systemet, placera sedan systemet på en plan yta.
7. Ta bort de fyra (M2.5x5) skruvarna som säkrar bildskärmsenheten på systemets chassi [1]. 8. Ta bort bildskärmsenheten från systemet [2].
Installera bildskärmsenheten Om denna uppgift OBS: Se till att gångjärnen är öppna maximalt innan du sätter tillbaka bildskärmsenheten på handledsstödet. Steg 1. Justera och placera systemets chassi under gångjärnen på bildskärmsenheten [1]. 2. Sätt tillbaka de fyra (M2.5x5) skruvarna som säkrar bildskärmsenheten på systemets chassi [2].
3. Sätta systemets chassi på bildskärmsenheten. OBS: Se till att du ser hur kabeln placeras under LCD installationen och även när du stänger LCD:n så att kablarna mellan LCD-enheten och chassit inte kläms.
4. Dra om den trådlösa antennen genom routingstyrningarna på moderkortet [1]. 5. Anslut-kabeln till kontakten på moderkortet [2]. 6. Anslut eDP-kabeln till kontakten på moderkortet [3]. 7. Placera eDP-kabelfästet på moderkortet [4]. 8. Sätt tillbaka de två (M2x3) skruvarna som säkrar eDP-kabelhållaren på moderkortet [5]. 9. Sätt fast tejpen som håller fast eDP-kabelhållaren på moderkortet [6].
Nästa Steg 1. 2. 3. 4. 5. Sätt tillbaka WLAN-kortet. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Bildskärmsram Ta bort bildskärmsramen Förutsättningar 1. 2. 3. 4. 5. 94 Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort bildskärmsenheten.
Steg 1. OBS: Bildskärmsramen kan inte återanvändas efter att ha tagits bort. Använd en plastrits för att försiktigt bända ut urtagen nära vänster och höger gångjärn på undersidan av bildskärmsramen [1]. 2. CAUTION: När man har bänt upp skärmens ram är det viktigt att bända längs utsidan av bildskärmens ram med händerna eller plastritsen – användning av en skruvmejsel eller andra skarpa föremål kan skada displaypanelen.
Installera bildskärmsramen Steg Justera bildskärmsramen med bildskärmsenheten och tryck bildskärmsramen försiktigt på plats.
Isärtagning och ihopsättning 97
Nästa Steg 1. 2. 3. 4. 5. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Bildskärmspanelen Ta bort bildskärmspanelen Förutsättningar 1. 2. 3. 4. 5. 6. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort bildskärmsenheten. Ta bort bildskärmsramen. Steg 1. Ta bort de två (M2.
2. Dra av den ledande tejpen [1] på bildskärmens kontakt. 3. Ta bort klisterremsan som håller fast skärmkabelns kontakt [2]. 4. Lyft haken och koppla bort bildskärmskabeln från kontakten på bildskärmspanelen [3, 4]. OBS: Dra inte och lossa stretchtejpen från bildskärmspanelen. Det finns ingen anledning att separera fästena från bildskärmspanelen.
Isärtagning och ihopsättning
Installera bildskärmspanelen Steg 1. Anslut bildskärmens kabel till kontakten och stäng haken [1, 2]. 2. Klistra fast klisterremsan för att fästa bildskärmens kabelkontakt [3]. 3. Klistra fast den ledande tejpen för att fästa bildskärmskabelns kontakt [4]. 4. OBS: LCD-panelen levereras med två (L+R) fästen som måste tåla först och sedan fästa två skruvar på basen av LCD-panelen. Sätt tillbaka de två (M2.5x3) skruvarna som håller fast bildskärmspanelen på handledsstödet.
Nästa Steg 1. 2. 3. 4. 5. 6. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn. Kamera Ta bort kameran Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. 9. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort bildskärmsenheten. Ta bort bildskärmsramen. Ta bort gångjärnskåporma. Ta bort bildskärmsgångjärnen.
Steg 1. Vik tillbaka de två ledande tejpremsorna som håller fast kameran [1]. 2. Lyft försiktigt bort kameramodulen från baksidan av bildskärmen [2]. 3. Koppla bort kamerakabeln från kontakten på kameramodulen [3]. Installera kameran Steg 1. Anslut kamerakabeln till kontakten på kameramodulen [1]. 2. Sätt in kameran i kortplatsen på bildskärmen bakre kåpa [2]. 3. Fäst de två ledande tejpremsorna ovanför kameran [3].
Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. Sätt tillbaka bildskärmspanelen. Sätt tillbaka bildskärmsgångjärnen. Sätt tillbaka gångjärnskåporma. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Gångjärnskåpor Ta bort gångjärnskåporna Förutsättningar 1. 2. 3. 4. 5. 6. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan.
Steg 1. Ta bort de två (M2x3) som fäster gångjärnskåpan på chassit [1]. 2. Kläm fast gångjärnskåporna så att gångjärnskåporna lossnar från hållarna på baksidan av bildskärmen och skjut inåt för att ta bort gångjärnskåporna från bildskärmsgångjärnet [2]. Installera gångjärnskåporna Steg 1. Placera gångjärnskåporna och skjut utåt på skärmens gångjärn [1]. 2. Sätt tillbaka de två (M2x3) skruvarna för att fästa gångjärnskåporna på skärmens gångjärn.
Nästa Steg 1. 2. 3. 4. 5. 6. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Bildskärmsgångjärnen Ta bort bildskärmsgångjärn Förutsättningar 1. 2. 3. 4. 5. 6. 7. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort bildskärmsenheten. Ta bort bildskärmsramen. Ta bort gångjärnskåporma.
Steg 1. Ta bort de fyra (M2.5x3) skruvarna som håller fast bildskärmsgångjärnen på bildskärmsenheten [1]. 2. Ta bort bildskärmsgångjärnen från bildskärmens bakre kåpa [2]. Installera bildskärmsgångjärn Steg 1. Placera bildskärmsgångjärnet på bildskärmsenheten. 2. Sätt tillbaka fyra (M2.5x3) skruvarna som håller fast bildskärmens gångjärn vid bildskärmsenheten.
Nästa Steg 1. 2. 3. 4. 5. 6. 7. Sätt tillbaka gångjärnskåporma. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Bildskärmens (EDP)-kabel Ta bort bildskärmskabeln Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. Följ anvisningarna i innan du arbetar inuti datorn. Ta bort microSD kort. Ta bort kåpan. Ta bort batteriet. Ta bort bildskärmsenheten. Ta bort bildskärmsramen.
9. Ta bort bildskärmspanelen. 10. Ta bort kameran. Steg Dra av den ledande tejpen och dra om bildskärmens kabel för att lossa den från tejpen och lyft upp bildskärmskabeln från bildskärmens bakre kåpa. Installera bildskärmskabeln Steg 1. Sätt fast skärmkabeln på skärmens bakre kåpa. 2. Fäst det ledande tejpen och rikta bildskärmens kabel till bildskärmens bakre kåpa.
Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Sätt tillbaka kameran. Sätt tillbaka bildskärmspanelen. Sätt tillbaka bildskärmsgångjärnen. Sätt tillbaka gångjärnskåporma. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ proceduren i när du har arbetat inuti datorn. Bildskärmens bakre höljesmontering Sätta tillbaka bildskärmens bakre kåpa Förutsättningar 1. 2. 3. 4. 5. 6. 7. 8. 9.
10. Ta bort kameran. 11. Ta bort bildskärmskabeln. Om denna uppgift Efter att man har utfört de föregående stegen lämnas man med bildskärmens bakre kåpa. Nästa Steg 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Sätt tillbaka bildskärmskabeln. Sätt tillbaka kameran. Sätt tillbaka bildskärmspanelen. Sätt tillbaka bildskärmsgångjärnen. Sätt tillbaka gångjärnskåporma. Sätt tillbaka bildskärmsramen. Sätt tillbaka bildskärmsenheten. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet.
3. 4. 5. 6. 7. 8. 9. Ta Ta Ta Ta Ta Ta Ta bort bort bort bort bort bort bort kåpan. batteriet. högtalaren. minnesmodulen. DC-in . WLAN-kortet. moderkortet. OBS: Systemkortet kan tas bort med kylfläns enhet fastsatt. 10. 11. 12. 13. Ta Ta Ta Ta bort bort bort bort knappcellsbatteriet. tangentbordet. strömbrytaren med fingeravtrycksläsare. SmartCard-läsararen. Om denna uppgift När du har utfört alla förhandsåtgärder återstår handledsstöds- och tangentbordsmonteringen Nästa Steg 1. 2. 3. 4. 5.
10. 11. 12. 13. Sätt tillbaka batteriet. Sätt tillbaka kåpan. Sätt tillbaka microSD-kortet. Följ anvisningarna i när du har arbetat inuti datorn.
5 Felsökning Ämnen: • • • Dell SupportAssist-diagnostik för kontroll av systemprestanda före start Systemets diagnosindikatorer WiFi-cykel Dell SupportAssist-diagnostik för kontroll av systemprestanda före start Om denna uppgift SupportAssist-diagnostiken (även kallad systemdiagnostik) utför en fullständig kontroll av din maskinvara. Dell SupportAssistdiagnostik för kontroll av systemprestanda före start är inbäddad med BIOS och startas av BIOS internt.
Vitt ljus — Nätadaptern är ansluten och batteriet har mer än 5 procent laddning. Gult sken — Datorn drivs med batteriet och batteriet har mindre än 5 procent laddning. Släckt ● Nätadaptern är ansluten och batteriet är fulladdat. ● Datorn drivs med batteriet och batteriet har mer än 5 procent laddning. ● Datorn är i strömsparläge, viloläge, eller avstängd. Ström- och statuslampa för batteri blinkar orange tillsammans med pipkoder som indikerar ett fel.
2. Stäng av modemet. 3. Stäng av den trådlösa routern. 4. Vänta 30 sekunder. 5. Slå på den trådlösa routern. 6. Slå på modemet. 7. Starta datorn.
6 Få hjälp Ämnen: • Kontakta Dell Kontakta Dell Förutsättningar OBS: Om du inte har en aktiv Internet-anslutning kan du hitta kontaktinformationen på ditt inköpskvitto, förpackning, faktura eller i Dells produktkatalog. Om denna uppgift Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område.