Latitude 5521 サービスマニュアル 規制モデル: P104F 規制タイプ: P104F003/P104F004 6 月 2021 年 Rev.
メモ、注意、警告 メモ: 製品を使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明しています。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 ©2021 Dell Inc.またはその関連会社。All rights reserved.(不許複製・禁無断転載)Dell、EMC、およびその他の商標は、Dell Inc.
目次 章 1: コンピュータ内部の作業............................................................................................................6 安全にお使いいただくために........................................................................................................................................... 6 コンピューター内部の作業..........................................................................................................................................6 サービス モードの起動.................................................................
セル バッテリーの取り外し................................................................................................................................... 38 4 セル バッテリーの取り付け................................................................................................................................... 39 アセンブリー内部フレーム............................................................................................................................................. 40 アセンブリー内部フレームの取り外し......................................
eDP ケーブルの取り外し........................................................................................................................................... 83 eDP ケーブルの取り付け........................................................................................................................................... 84 センサーボード.................................................................................................................................................................. 86 センサー ボードの取り外し..............
1 コンピュータ内部の作業 トピック: • 安全にお使いいただくために 安全にお使いいただくために 身体の安全を守り、PC を損傷から保護するために、次の安全に関する注意に従ってください。特に記載のない限り、この文書に 記載される各手順は、お使いの PC に付属の「安全にお使いいただくための注意事項」をすでにお読みいただいていることを前提 とします。 警告: PC 内部の作業を行う前に、お使いの PC に付属している「安全にお使いいただくために」をお読みください。安全にお 使いいただくためのベストプラクティスの詳細については、法令遵守ホームページ(www.dell.
2. PC をシャットダウンします。[Start ] > [ Power] > [ Shut down]の順にクリックします。 メモ: 他のオペレーティング システムを使用している場合は、お使いのオペレーティング システムのシャットダウン方法 に関するマニュアルを参照してください。 3. PC および取り付けられているすべてのデバイスをコンセントから外します。 4. キーボード、マウス、モニターなど取り付けられているすべてのネットワークデバイスや周辺機器を PC から外します。 注意: ネットワーク ケーブルを外すには、まずケーブルのプラグを PC から外し、次にケーブルをネットワークデバイスか ら外します。 5.
● ● ● ● ● キットのみを使用してください。ワイヤレスのリストストラップは使用しないでください。リストストラップの内部ワイヤー は、通常の装着によって損傷が発生します。よって、事故による ESD のハードウェア損傷を避けるため、リスト・ストラップ・ テスターを使用して定期的に確認する必要があります。リストストラップとボンディングワイヤーは少なくとも週に一度テス トすることをお勧めします。 ESD リスト・ストラップ・テスター – ESD ストラップの内側にあるワイヤーは、時間の経過に伴って損傷を受けます。監視さ れないキットを使用する場合には、サービスコールのたびに定期的にストラップをテストすることがベストプラクティスです。 最低でも週に一度テストします。テストには、リスト・ストラップ・テスターを使用することが最善です。リスト・ストラッ プ・テスターを所有していない場合には、地域オフィスに在庫を問い合わせてください。テストを実行するには、リストスト ラップを手首に装着した状態で、リストストラップのボンディングワイヤーをテスターに接続し、ボタンを押してテストを行 います。テスト合格の場合には緑の
サービス モードの終了 サービス モードを使用すると、バッテリー ケーブルをシステム ボードから外さなくても、すぐに PC の電源を切って修復を行う ことができます。 サービス モードを終了するには、次のように操作します。 1. AC アダプターを PC の電源アダプター ポートに接続します。 2. 電源ボタンを押してコンピュータの電源をオンにします。PC は自動的に通常機能モードに戻ります。 PC 内部の作業を終えた後に このタスクについて 注意: PC 内部にネジが残っていたり、緩んでいたりすると、PC に深刻な損傷を与える恐れがあります。 手順 1. すべてのネジを取り付けて、PC 内部に外れたネジが残っていないことを確認します。 2. PC での作業を始める前に、取り外したすべての外付けデバイス、周辺機器、ケーブルを接続します。 3. PC での作業を始める前に、取り外したすべてのメディアカード、ディスク、その他のパーツを取り付けます。 4. PC、および取り付けられているすべてのデバイスをコンセントに接続します。 5.
2 コンポーネントの取り外しと取り付け メモ: 本書の画像は、ご注文の構成によってお使いの PC と異なる場合があります。 トピック: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 推奨ツール ネジのリスト システムの主要なコンポーネント SIM カードトレイ Micro Secure Digital(SD)カード ベースカバー ワイヤレスカード WWAN(ワイヤレスワイドエリアネットワーク)カード ソリッドステート ドライブ メモリ ハードドライブアセンブリー バッテリーケーブル バッテリー アセンブリー内部フレーム LED ボード ヒートシンク スピーカー USB Type-C ブラケット システム ボード 電源ボタンボード スマート カード リーダー コイン型電池 キーボード アセンブリー キーボード ブラケット ディスプレイ アセンブリー ディスプレイ ベゼル ディスプレイパネル カメラ/マイクロフォン モジュール eDP/モニター ケーブル センサーボード ディスプレイ ヒンジ ディスプレイ背面カバー パームレ
ネジのリスト メモ: コンポーネントからネジを取り外す際は、ネジの種類、ネジの数量をメモし、その後ネジの保管箱に入れておくことを お勧めします。これは、コンポーネントを交換する際に正しいネジの数量と正しいネジの種類を保管しておくようにするため です。 メモ: 一部のコンピューターには、磁性面があります。コンポーネントを交換する際、ネジが磁性面に取り付けられたままに なっていないことを確認してください。 メモ: ネジの色は、発注時の構成によって異なります。 表 1. ネジのリスト ネジの種類 数 ネジの画像 ベース カバー 拘束ネジ 8 該当なし ワイヤレスカード 拘束ネジ 1 該当なし コンポーネント WWAN(ワイヤレスワイド エリ M2x3 ア ネットワーク)カード 1 M.2 2230 ソリッドステート ド M2x3 ライブ 4 M.
表 1. ネジのリスト (続き) ネジの種類 数 キーボード アセンブリー M2x2 18 キーボード ブラケット M2x2 5 コンポーネント ディスプレイ アセンブリー ディスプレイヒンジ モニター パネル 12 M2.5x5(パームレスト アセン 4 ブリーへのディスプレイ ヒン ジ固定用) M2.5x3(ディスプレイ背面カ バーへのディスプレイ ヒンジ 固定用) 4 M2.
システムの主要なコンポーネント 1.
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
手順 1. ピンをリリース ホールに挿入し、SIM カード トレイを開けます。 2. ピンを押してロックを解除し、SIM カード トレイを取り出します。 3. SIM カード トレイを引き出してシステムのスロットから取り外します。 4. SIM カードを SIM カードトレイから取り外します。 5.
手順 1. SIM カード トレイの穴にピンを差し込み、トレイが解放されるまで内側に押し込みます 2. SIM カード トレイを引き出して PC のスロットから取り外します。 3. 金属製の接触部を上に向けて、SIM カード トレイに SIM カードを配置します。 4. SIM カード トレイを PC のスロットに合わせ、慎重に差し込みます。 5.
手順 1. microSD カードを押して、スロットからリリースします。 2.
手順 1. microSD カードをシステムのスロットに合わせます。 2. 所定の位置にカチッと収まるまで、microSD カードをスライドさせてスロットに差し込みます。 次の手順 1. 「PC 内部の作業を終えた後に」の手順に従います。 ベースカバー ベース カバーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5.
手順 1. ベース カバーをパーム レストとキーボード アセンブリーに固定している 9 本の拘束ネジを緩めます。 2. プラスチック スクライブの平らな端部を使用して、ベース カバー上部の端にある U 字型のくぼみからベース カバーをこじ開 け、側面もこじ開けて、パームレストとキーボード アセンブリーからベース カバーを外します。 3.
コンポーネントの取り外しと取り付け
手順 1. ベース カバーをパームレストとキーボード アセンブリーの上部にセットします。 2. ベースカバーのネジ穴をパームレストとキーボード アセンブリーのネジ穴に合わせて、ベース カバーを所定の位置にはめ込み ます。 3. ベース カバーをパーム レストとキーボード アセンブリーに固定する 9 本の拘束ネジを締めます。 次の手順 1. 2. 3. 4. microSD カードを取り付けます。 SIM カードを取り付けます。 サービス モードを終了します。 「PC 内部の作業を終えた後に」の手順に従います。 ワイヤレスカード ワイヤレス カードの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5.
手順 1. メモ: WLAN カードをシステムから取り外す際に、WLAN カードを所定の位置に固定している粘着パッドが WLAN カードと 一緒にシステムから取り外されてしまう場合は、粘着パッドをシステムに再度貼り付けます。 ワイヤレスカード ブラケットをワイヤレス カードとシステム ボードに固定している拘束ネジを緩めます。 2. ワイヤレスカードブラケットをワイヤレスカードから取り外します。 3. アンテナケーブルをワイヤレスカードから外します。 4. プラスチック スクライブを使用して、ワイヤレス カードを粘着パッドからこじ開けます。 5.
手順 1. アンテナケーブルをワイヤレスカードに接続します。 次の表に、お使いの PC がサポートするワイヤレス カード用アンテナケーブルの色分けを示します。 表 2. アンテナケーブルの色分け ワイヤレスカードのコ ネクター アンテナケーブルの色 シルクスクリーンのマーク メイン 白色 メイン △(白色の三角形) 補助 黒色 補助 ▲(黒色の三角形) 2. ワイヤレスカードの切り込みをシステム ボードのワイヤレスカード スロットのタブに合わせます。 3. ワイヤレス カードを斜めにして、システム ボードのワイヤレスカード スロットに差し込みます。 4. ワイヤレス カードを粘着パッドに貼り付けます。 5. ワイヤレスカード ブラケットのネジ穴をワイヤレス カードとシステム ボードのネジ穴に合わせます。 6. ワイヤレスカード ブラケットをワイヤレス カードとシステム ボードに固定する拘束ネジを締めます。 次の手順 1. 2. 3. 4.
5. 「PC 内部の作業を終えた後に」の手順に従います。 WWAN(ワイヤレスワイドエリアネットワーク)カード WWAN カードの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 このタスクについて 次の画像は WWAN カードの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. WWAN カード ブラケットを WWAN カードに固定している 1 本のネジ(M2x3)を取り外します。 2. WWAN カード ブラケットを持ち上げてシステムから取り出します。 3. アンテナ ケーブルを WWAN カードのコネクターから外します。 4.
WWAN カードの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 次の画像は WWAN カードの場所を示すもので、取り付け手順を視覚的に表しています。 手順 1. WWAN カードにアンテナケーブルを接続します。 次の表は、アンテナケーブルの色分けを示しています。 表 3. アンテナケーブルの色分け ワイヤレスカードのコ ネクター アンテナケーブルの色 シルクスクリーンのマーク メイン 白色 メイン △(白色の三角形) 補助 黒色 補助 ▲(黒色の三角形) 2. WWAN カードの切り込みの位置を合わせ、WWAN カードを傾けて WWAN カード スロットに差し込みます。 3. WWAN カード ブラケットをシステム ボードと WWAN カードに合わせてセットします。 4.
次の手順 1. microSD カードを取り付けます。 2. SIM カードを取り付けます。 3. ベース カバーを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 ソリッドステート ドライブ 2230 ソリッドステート ドライブの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 メモ: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 2. 3. 4. 5. メモ: データ ロスを防ぐため、PC の電源が入っている状態、またはスリープ状態のときにソリッドステート ドライブを取 り外さないでください。 サービス モードを起動します。 SIM カードを取り外します。 microSD カードを取り外します。 ベース カバーを取り外します。 このタスクについて メモ: 発注時の構成に応じて、PC の M.2 スロットで 2230 ソリッドステート ドライブ、または 2280 ソリッドステート ドライ ブがサポートされる場合があります。 メモ: この手順は、M.
3. ソリッドステート ドライブ ブラケットをスライドさせて、システムから取り外します。 4. ソリッドステート ドライブをスライドさせて、M.2 スロットから取り外します。 2230 ソリッドステート ドライブの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて メモ: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 メモ: 発注時の構成に応じて、PC の M.2 スロットで 2230 ソリッドステート ドライブ、または 2280 ソリッドステート ドライ ブがサポートされる場合があります。 メモ: この手順は、M.2 スロットに 2230 ソリッドステート ドライブを取り付けている場合にのみ適用されます。 次の画像は、M.2 スロットに取り付けられている 2230 ソリッドステート ドライブの位置を示すもので、取り付け手順を視覚的に 表しています。 手順 1.
2230 ソリッドステート ドライブ スロット 2 の取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 メモ: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 2. 3. 4. 5. メモ: データ ロスを防ぐため、PC の電源が入っている状態、またはスリープ状態のときにソリッドステート ドライブを取 り外さないでください。 サービス モードを起動します。 SIM カードを取り外します。 microSD カードを取り外します。 ベース カバーを取り外します。 このタスクについて メモ: 発注時の構成に応じて、PC の M.2 スロットで 2230 ソリッドステート ドライブ、または 2280 ソリッドステート ドライ ブがサポートされる場合があります。 メモ: この手順は、M.2 スロットに取り付けられた 2230 ソリッドステート ドライブが搭載されている PC にのみ適用されま す。 次の画像は、取り付けられている 2230 ソリッドステート ドライブの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1.
このタスクについて メモ: ソリッドステートドライブは非常に壊れやすいものです。取り扱う場合は細心の注意を払ってください。 メモ: 発注時の構成に応じて、PC の M.2 スロットで 2230 ソリッドステート ドライブ、または 2280 ソリッドステート ドライ ブがサポートされる場合があります。 メモ: この手順は、M.2 スロットに 2230 ソリッドステート ドライブを取り付けている場合にのみ適用されます。 次の画像は、M.2 スロットに取り付けられている 2230 ソリッドステート ドライブの位置を示すもので、取り付け手順を視覚的に 表しています。 手順 1. 2230 ソリッドステート ドライブの切り込みをソリッドステート ドライブ スロットのタブに合わせます。 2. 2230 ソリッドステート ドライブを 2230 ソリッドステート ドライブ スロットに差し込みます。 3. ソリッドステート ドライブをソリッドステート ドライブ スロットに固定する 1 本のネジ(M2x2)を取り付けます。 4. サーマル プレートをソリッドステート ドライブにセットします。 5.
4. microSD カードを取り外します。 5. ベース カバーを取り外します。 このタスクについて メモ: 発注時の構成に応じて、PC の M.2 スロットで 2280 ソリッドステート ドライブ、または 2230 ソリッドステート ドライ ブがサポートされる場合があります。 メモ: この手順は、M.2 スロットに取り付けられた 2280 ソリッドステート ドライブが搭載されている PC にのみ適用されま す。 次の画像は、M.2 スロットに取り付けられている 2280 ソリッドステート ドライブの位置を示すもので、取り外し手順を視覚的に 表しています。 手順 1. ソリッドステート ドライブのサーマル プレートをパームレストとキーボード アセンブリーに固定している 2 本のネジ(M2x2) を外します。 2. ソリッドステート ドライブのサーマル プレートをシステムから取り外します。 3. 2280 ソリッドステート ドライブを引き出して持ち上げ、システムの M.
手順 1. 2280 ソリッドステート ドライブの切り込みをソリッドステート ドライブ スロットのタブに合わせます。 2. 2280 ソリッドステート ドライブを傾けて、ソリッドステート ドライブ スロットにしっかりと差し込みます。 3. ソリッドステート ドライブのサーマル プレートをソリッドステート ドライブ上にセットします。 4. ソリッドステート ドライブとサーマル プレートのネジ穴を、パームレストとキーボード アセンブリーのネジ穴に合わせます。 5. 2280 ソリッドステート ドライブをパームレストとキーボード アセンブリーに固定する 2 本のネジ(M2x2)を取り付けます。 次の手順 1. microSD カードを取り付けます。 2. SIM カードを取り付けます。 3. ベース カバーを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 メモリ メモリー モジュールの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4.
手順 1. メモリー モジュールが持ち上がるまで、メモリー モジュールを固定している固定クリップを引き上げます。 2.
手順 1. メモリーモジュールの切り込みをメモリーモジュールスロットのタブに合わせます。 2. メモリ モジュールを傾けて、メモリモジュール スロットにしっかりと差し込みます。 3. 所定の位置にカチッと収まるまで、メモリーモジュールを押し込みます。 メモ: カチッという感触がない場合は、メモリーモジュールを取り外して、もう一度差し込んでください。 メモ: 手順 1~4 を繰り返して、PC に他のメモリー モジュールを取り付けます。 次の手順 1. ベース カバーを取り付けます。 2. microSD カードを取り付けます。 3. SIM カードを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 ハードドライブアセンブリー ハード ドライブの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5.
手順 1. PC の HDD の位置を確認します。 2. HDD ケーブルをシステム ボードから外します。 3. HDD をシステム ボードに固定している 4 本のネジ(M2x4)を外します。 4.
手順 1. PC のシステム ボードのスロットの位置を確認します。 2. 位置を合わせて HDD をコンピューターに取り付けます。 3. HDD を PC に固定する 4 本のネジ(M2x4)を取り付けます。 4. HDD ケーブルをシステム ボードのコネクターに接続します。 次の手順 1. ベース カバーを取り付けます。 2. microSD カードを取り付けます。 3. SIM カードを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 バッテリーケーブル バッテリー ケーブルの取り外し 前提条件 1. 2. 3. 4.
手順 1. バッテリーを裏返し、バッテリーのルーティング ガイドからバッテリー ケーブルを外します。 2. バッテリー ケーブルをバッテリーのコネクターから外します。 3.
手順 1. バッテリー ケーブルをバッテリーに合わせて配置します。 2. バッテリー ケーブルをバッテリーの配線ガイドに沿って配線します。 3. バッテリーケーブルをバッテリーのコネクタに接続します。 次の手順 1. 2. 3. 4.
● 膨張によってリチウムイオン バッテリがコンピュータ内で詰まってしまう場合、穴を開けたり、曲げたり、押しつぶした りすると危険なため、無理に取り出そうとしないでください。そのような場合は、デル テクニカル サポートにお問い合わ せください。www.dell.com/contactdell を参照してください。 ● 必ず、www.dell.com または Dell 認定パートナーおよび再販業者から正規のバッテリを購入してください。 4 セル バッテリーの取り外し 前提条件 1. 2. 3. 4. 「PC 内部の作業を始める前に」の手順に従います。 SIM カードを取り外します。 microSD カードを取り外します。 ベース カバーを取り外します。 このタスクについて 次の画像は 4 セル(64 Wh)バッテリーの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. バッテリー ケーブルをシステム ボードのコネクターから外します。 2. 4 セル バッテリーをパームレストとキーボード アセンブリーに固定している 3 本のネジ(M2x4)を外します。 3.
4 セル バッテリーの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 次の画像は 4 セル(64 Wh)バッテリーの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1. 位置合わせポストを使用して、4 セル バッテリーをパームレストとキーボード アセンブリーにスライドさせてセットします。 2. 4 セル バッテリーのネジ穴を、パームレストとキーボード アセンブリーのネジ穴に合わせます。 3. 4 セル バッテリーをパームレストとキーボード アセンブリーに固定する 3 本のネジ(M2x4)を取り付けます。 4. バッテリー ケーブルをシステム ボードのコネクターに接続します。 次の手順 1. 2. 3. 4.
アセンブリー内部フレーム アセンブリー内部フレームの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. SIM カードを取り外します。 3. microSD カードを取り外します。 4. ベース カバーを取り外します。 5. バッテリーを取り外します。 6. ハード ドライブを取り外します。 7. WLAN カードを取り外します。 8.
手順 1. アンテナ ケーブルをアセンブリー内部フレームの配線ガイドから外します。 2. アセンブリー内部フレーム ブラケットを、システム ボードとパームレスト アセンブリーに固定している 2 本のネジ(M2x3) を取り外します。 3. アセンブリー内部フレーム ブラケットを取り外します。 4. アセンブリー内部フレームを、システム ボードとパームレスト アセンブリーに固定している 17 本のネジ(M2x3)を取り外し ます。 5.
アセンブリー内部フレームの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 次の画像はアセンブリー内部フレームの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1.
メモ: アセンブリー内部フレームの左上隅にあるタブがパームレスト アセンブリーのタブの下に取り付けられていること を確認します。 2. アセンブリー内部フレームを、システム ボードとパームレスト アセンブリーに固定する 17 本のネジ(M2x3)を取り付けます。 3. アセンブリー内部フレーム ブラケットを、システム ボードとパームレスト アセンブリーに固定する 2 本のネジ(M2x3)を取 り付けます。 4. スピーカー ケーブルをアセンブリー内部フレームの配線ガイドに沿ってしっかりと配線し、システム ボードのコネクターにス ピーカー ケーブルを接続します。 5. アンテナ ケーブルをアセンブリー内部フレームの配線ガイドに沿って配線します。 次の手順 1. バッテリーを取り付けます。 2. ハード ドライブを取り付けます。 3. WWAN カードを取り付けます。 4. WLAN カードを取り付けます。 5. ベース カバーを取り付けます。 6. microSD カードを取り付けます。 7. SIM カードを取り付けます。 8. サービス モードを終了します。 9.
手順 1. LED ボード ケーブルとタッチパッド ケーブルをシステム ボードのコネクターから外します。 2. LED ボード ケーブルをコイン型電池からはがします。 3. LED ボードをパームレスト アセンブリーに固定している 1 本のネジ(M2x3)を外します。 4.
手順 1. LED ボードのネジ穴をパームレスト アセンブリーのネジ穴の位置に合わせます。 2. LED ボードをパームレスト アセンブリーに固定する 1 本のネジ(M2x3)を取り付けます。 3. LED ボード ケーブルを配線し、そのケーブルをシステム ボードのコネクターに接続します。 注意: コイン型電池の下に LED ボード ケーブルを配線しないでください。LED ボード ケーブルを不適切に配線すると、 LED ボード、LED ボード ケーブル、システム ボードが破損する場合があります。 4. タッチパッドケーブルをシステム ボードのコネクタに接続します。 次の手順 1. アセンブリー内部フレームを取り付けます。 2. バッテリーを取り付けます。 3. ハード ドライブを取り付けます。 4. WWAN カードを取り付けます。 5. WLAN カードを取り付けます。 6. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り付けます。 7. ベース カバーを取り付けます。 8. microSD カードを取り付けます。 9. SIM カードを取り付けます。 10.
注意: プロセッサーの冷却効果を最大にするために、ヒート シンクの放熱部分には触れないでください。皮脂が付着する と、サーマルグリースの放熱機能が低下する場合があります。 2. 3. 4. 5. メモ: 通常のオペレーション中に、ヒート シンクが高温になる場合があります。温度が十分に下がりヒート シンクが冷え るのを待って、触ってください。 サービス モードを起動します。 SIM カードを取り外します。 microSD カードを取り外します。 ベース カバーを取り外します。 このタスクについて 次の画像は、UMA 構成のシステムでのヒート シンクとファン アセンブリーの位置を示すもので、取り外し手順を視覚的に表して います。 手順 1. システム ファンをフレームに固定している 2 本のネジ(M2x4)を外します。 2. ヒート シンク上の表示とは逆の順序で、ヒート シンクとファン アセンブリーをシステム ボードに固定している 4 本の拘束ネ ジを緩めます。 3.
ヒート シンクとファン アセンブリーの取り付け:UMA 構成 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 注意: ヒート シンクの位置が正しく合っていないと、システム ボードとプロセッサーを損傷する可能性があります。 メモ: システム ボードまたはヒート シンクのいずれかを取り付ける場合は、熱伝導性を確保するために、キット内のサーマル パッド/ペーストを使用してください。 このタスクについて 次の画像は、UMA 構成のシステムでのヒート シンクとファン アセンブリーの位置を示すもので、取り付け手順を視覚的に表して います。 手順 1. ヒート シンクとファン アセンブリーのネジ穴をシステム ボードのネジ穴に合わせます。 2. ヒート シンク上に表示されているシーケンシャルな順序で、ヒート シンクとファン アセンブリーをシステム ボードに固定す る 4 本の拘束ネジを締めます。 3. ファンケーブルをシステム ボード上のコネクタに接続します。 4.
次の手順 1. microSD カードを取り付けます。 2. SIM カードを取り付けます。 3. ベース カバーを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 ヒート シンクとファン アセンブリーの取り外し:専用構成 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 注意: プロセッサーの冷却効果を最大にするために、ヒート シンクの放熱部分には触れないでください。皮脂が付着する と、サーマルグリースの放熱機能が低下する場合があります。 2. 3. 4. 5.
手順 1. システム ファンをフレームに固定している 2 本のネジ(M2x4)を外します。 2. ヒート シンク上の表示とは逆の順序で、ヒート シンクとファン アセンブリーをシステム ボードに固定している 6 本のネジ (M2x3)を緩めます。 3. ファン ケーブルをシステム ボード上のコネクタから外します。 4.
手順 1. ヒート シンクとファン アセンブリーのネジ穴をシステム ボードのネジ穴に合わせます。 2. ヒート シンク上に表示されているシーケンシャルな順序で、ヒート シンクをシステム ボードに固定する 6 本のネジ(M2x3) を締めます。 3. ファンケーブルをシステム ボード上のコネクタに接続します。 4. システム ファンをフレームに固定する 2 本のネジ(M2x4)を取り付けます。 次の手順 1. microSD カードを取り付けます。 2. SIM カードを取り付けます。 3. ベース カバーを取り付けます。 4. サービス モードを終了します。 5.
スピーカー スピーカーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. SIM カードを取り外します。 3. microSD カードを取り外します。 4. ベース カバーを取り外します。 5. バッテリーを取り外します。 6. ハード ドライブを取り外します。 このタスクについて 次の画像はスピーカーの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. スピーカー ケーブルをパームレストとキーボード アセンブリーに固定しているテープをはがします。 2. スピーカー ケーブルのルーティングをメモしてから、スピーカー ケーブルをパームレストとキーボード アセンブリーのルーテ ィング ガイドから外します。 3. スピーカー ケーブルをシステム ボードから外します。 4.
手順 1. 位置合わせポストとゴム製グロメットを使用して、スピーカーをパームレストとキーボード アセンブリーのスロットにセット します。 2. システム ボードにスピーカー ケーブルを接続します。 3. システムの左下隅に沿ってスピーカー ケーブルを配線し、内部フレームのルーティング チャネルにしっかりと配線されている ことを確認します。 次の手順 1. バッテリーを取り付けます。 2. ハード ドライブを取り付けます。 3. ベース カバーを取り付けます。 4. microSD カードを取り付けます。 5. SIM カードを取り付けます。 6. 「PC 内部の作業を終えた後に」の手順に従います。 USB Type-C ブラケット USB Type-C ブラケットの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5.
手順 1. USB Type-C ブラケットをシステム ボードに固定している 3 本のネジ(M2x5)を外します。 2.
手順 1. USB Type-C ブラケットをシステム ボードにセットして、ブラケットとシステム ボードの穴の位置を合わせます。 2. 3 本のネジ(M2x5)を取り付けて、USB Type-C ブラケットをシステム ボードに固定します。 次の手順 1. ベース カバーを取り付けます。 2. microSD カードを取り付けます。 3. SIM カードを取り付けます。 4. サービス モードを終了します。 5. 「PC 内部の作業を終えた後に」の手順に従います。 システム ボード システム ボードの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. メモリー モジュールを取り外します。 7. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り外します。 8. WLAN カードを取り外します。 9. WWAN カードを取り外します。 10. バッテリーを取り外します。 11.
このタスクについて 次の画像はシステム ボードの位置を示すもので、取り外し手順を視覚的に表しています。 コンポーネントの取り外しと取り付け 55
手順 メモ: システム ボードは、ヒート シンクを取り付けた状態で取り外したり取り付けたりできます。そうすることで、手順をシ ンプルにし、システム ボードとヒートシンクの間のヒート シンクを保持できます。そうするためには、技術者がシステム フ ァンをシステム ボードに固定している 2 本のネジ(M2x5)を外すことも必要です。 メモ: 指紋認証リーダー搭載のモデルでは、システム ボードをパームレスト アセンブリーとキーボード アセンブリーから取り 外す前に、指紋認証リーダー ケーブルをシステム ボードのコネクターから外します。 1. 指紋認証リーダー ケーブルをシステム ボードのコネクターから外します。 2. マイラー テープをはがして、センサー ケーブルを外します。 3. USB Type-C ブラケットをシステム ボードに固定している 3 本のネジ(M2x4)を外します。 4. USB Type-C ブラケットを持ち上げて、システム ボードから取り外します。 5. eDP/モニター ケーブル ブラケットをシステム ボードに固定している 2 本のネジ(M2x3)を外します。 6.
コンポーネントの取り外しと取り付け 57
手順 メモ: システム ボードは、サーマル モジュールを取り付けた状態で取り外したり取り付けたりできます。そうすることで、手 順をシンプルにし、システム ボードとヒートシンクの間のサーマル ボンドを保持できます。そうするためには、技術者がシ ステム ファンをシステム ボードに固定している 2 本のネジ(M2x5)を外すことも必要です。 1. USB Type-C コネクターが先端に入り込むまでシステム ボードをヒンジ サドルに差し込み、システム ボードのネジ穴をパーム レスト アセンブリーとキーボード アセンブリーのネジ穴に合わせます。 2. システム ボードをパームレスト アセンブリーとキーボード アセンブリーに固定する 3 本のネジ(M2x3)を取り付けます。 3. 指紋認証リーダーをシステム ボードのコネクターに接続します。 4. センサー ケーブルをシステム ボードのコネクターに接続し、マイラー テープをその上に貼り付けます。 5. USB Type-C ブラケットをシステム ボードに合わせて配置します。 6.
9. バッテリーを取り外します。 10. アセンブリー内部フレームを取り外します。 11. システム ボードを取り外します。 このタスクについて 次の画像は電源ボタン ボードの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. 電源ボタン ボードをパームレスト アセンブリーに固定している 2 本のネジ(M2x2)を外します。 2.
手順 1. 電源ボタン ボードをパームレスト アセンブリーの位置に合わせて配置します。 2. 電源ボタン ボードをパームレスト アセンブリーに固定する 2 本のネジ(M2x2)を取り付けます。 次の手順 1. システム ボードを取り付けます。 2. アセンブリー内部フレームを取り付けます。 3. バッテリーを取り付けます。 4. WWAN カードを取り付けます。 5. WLAN カードを取り付けます。 6. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り付けます。 7. メモリ モジュールを取り付けます。 8. ベース カバーを取り付けます。 9. microSD カードを取り付けます。 10. SIM カードを取り付けます。 11. 「PC 内部の作業を終えた後に」の手順に従います。 スマート カード リーダー スマート カード リーダーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5.
7. 8. 9. 10. WLAN カードを取り外します。 WWAN カードを取り外します。 バッテリーを取り外します。 アセンブリー内部フレームを取り外します。 このタスクについて 以下の画像はスマート カード リーダーの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. ラッチを開いて、スマート カード リーダー ケーブルを USH ボードのコネクターから外します。 2. スマート カード リーダーから粘着テープをはがします。 3. スマート カード リーダーをパームレスト アセンブリーに固定している 3 本のネジ(M2x3)を取り外します。 4.
このタスクについて 次の画像はスマート カード リーダーの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1. スマート カード リーダーをパームレスト アセンブリーに合わせて配置します。 2. スマート カード リーダーをパームレスト アセンブリーに固定する 3 本のネジ(M2x3)を取り付けます。 3. 粘着テープをスマート カード リーダーの裏に貼り付けます。 4. スマート カード リーダー ケーブルを USH ボードのコネクターに接続します。 次の手順 1. 2. 3. 4. 5. 6. 7. 8. 9.
10.「PC 内部の作業を終えた後に」の手順に従います。 コイン型電池 コイン型電池の取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 注意: コイン型電池を取り外すと、BIOS セットアッププログラムの設定がデフォルト状態にリセットされます。コイン型 電池を取り外す前に、BIOS セットアッププログラムの設定を書き留めておくことをお勧めします。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. メモリー モジュールを取り外します。 7. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り外します。 8. WLAN カードを取り外します。 9. WWAN カードを取り外します。 10. バッテリーを取り外します。 11. システム構成に基づいて、UMA または専用ヒート シンクを取り外します。 12.
コイン型電池の取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて 次の図は、コイン型電池の場所を示すもので、取り付け手順を視覚的に表しています。 手順 1. コイン型電池をパームレスト アセンブリーのスロットに貼り付けます。 2. コイン型電池ケーブルをコネクターに接続します。 次の手順 1. アセンブリー内部フレームを取り付けます。 2. バッテリーを取り付けます。 3. WWAN カードを取り付けます。 4. WLAN カードを取り付けます。 5. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り付けます。 6. メモリ モジュールを取り付けます。 7. ベース カバーを取り付けます。 8. microSD カードを取り付けます。 9. SIM カードを取り付けます。 10. サービス モードを終了します。 11.
キーボード アセンブリー キーボードアセンブリーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. メモリー モジュールを取り外します。 7. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り外します。 8. WLAN カードを取り外します。 9. WWAN カードを取り外します。 10. バッテリーを取り外します。 11. システム構成に基づいて、UMA または専用ヒート シンクを取り外します。 12. アセンブリー内部フレームを取り外します。 13.
手順 1. メモ: USH モジュールが付属しているモデルの場合は、USH ケーブルをキーボード ブラケットから外します。 ラッチを持ち上げて、キーボード ケーブルとキーボード バックライト ケーブル(キーボード バックライト付属モデルの場合) をタッチパッドから外します。 2. キーボード アセンブリーをパームレストに固定している 27 本のネジ(M2x2)を外します。 3. パームレストからキーボード アセンブリーを慎重に持ち上げます。 4.
次の画像はキーボード アセンブリーの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1. キーボード アセンブリーをパームレスト アセンブリーに合わせて配置します。 2. キーボード アセンブリーをパームレストに固定する 27 本のネジ(M2x2)を取り付けます。 3. キーボード ケーブルとキーボード バックライト ケーブルをタッチパッド上のコネクターに接続します。 メモ: USH モジュールが付属しているモデルの場合は、USH ケーブルをキーボード ブラケットに接続します。 次の手順 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
11. SIM カードを取り付けます。 12. サービス モードを終了します。 13.「PC 内部の作業を終えた後に」の手順に従います。 キーボード ブラケット キーボード ブラケットの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. メモリー モジュールを取り外します。 7. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り外します。 8. WLAN カードを取り外します。 9. WWAN カードを取り外します。 10. バッテリーを取り外します。 11. システム構成に基づいて、UMA または専用ヒート シンクを取り外します。 12. アセンブリー内部フレームを取り外します。 このタスクについて 次の画像はキーボード ブラケットの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1.
キーボード ブラケットの取り付け 前提条件 コンポーネントを交換する場合、取り付け手順を実行する前に、既存のコンポーネントを取り外してください。 このタスクについて メモ: システム ボードはヒート シンクを取り付けたままで取り付けることができます。そうすることで、手順をシンプルにす るとともに、システム ボードとヒート シンクの間のサーマル ボンドを保持できます。 次の画像はキーボード ブラケットの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1. キーボードをキーボード ブラケットに合わせてセットします。 2. 14 本のネジ(M2x2)を取り付けてキーボードをキーボード ブラケットに固定します。 次の手順 1. キーボードアセンブリー を取り付けます。 2. システム ボードを取り付けます。 3. アセンブリー内部フレームを取り付けます。 4. スピーカーを取り付けます。 5. システム構成に基づいて、UMA または専用ヒート シンクを取り付けます。 6. バッテリーを取り付けます。 7. WWAN カードを取り付けます。 8. WLAN カードを取り付けます。 9.
ディスプレイ アセンブリー ディスプレイ アセンブリーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. WLAN カードを取り外します。 7.
コンポーネントの取り外しと取り付け 71
手順 1. 粘着テープを部分的にはがして、WLAN アンテナ ケーブルと WWAN アンテナ ケーブルをシステム ボードの配線ガイドから外 します。 2. eDP ケーブル ブラケットをシステム ボードに固定している 2 本のネジ(M2x3)を外します。 3. eDP ケーブル ブラケットを持ち上げてシステムから取り外します。 4. モニター ケーブルをシステム ボードに固定しているテープを剥がします。 5. プル タブを使用して、モニター ケーブルをシステム ボードのコネクターから外します。 6. eDP ケーブルをシステム ボードのコネクターから外し、配線ガイドから外します。 7. (IR カメラ搭載モデルの場合)IR カメラ ケーブルをシステム ボード上のコネクターから外します。 8. (タッチスクリーン搭載モデルの場合)タッチスクリーン ケーブルをシステム ボード上のコネクターから外します。 9. ディスプレイ ヒンジをシステム ボードに固定している 6 本のネジ(M2.5x5)を外します。 10.
コンポーネントの取り外しと取り付け 73
手順 1. ディスプレイ アセンブリーをシステムに配置します。ディスプレイ ヒンジのネジ穴とパームレスト アセンブリーのネジ穴の 位置を合わせます。 2. ディスプレイ ヒンジをパームレスト アセンブリーに固定する 6 本のネジ(M2.5x5)を取り付けます。 3. ディスプレイを閉じます。 4. ディスプレイおよび eDP のケーブルをシステム ボードの配線ガイドに沿って配線します。 5. eDP ケーブルをシステム ボードのコネクタに接続します。 6. モニター ケーブルをシステム ボードのコネクタに接続します。 7. モニター ケーブルをシステム ボードに固定するテープを貼り付けます。 8. (IR カメラ搭載モデルの場合)IR カメラ ケーブルをシステム ボード上のコネクターに接続します。 9. (タッチスクリーン搭載モデルの場合)タッチスクリーン ケーブルをシステム ボード上のコネクターに接続します。 10. eDP ケーブル ブラケットのネジ穴をシステム ボードのネジ穴に合わせます。 11. eDP ケーブル ブラケットをシステム ボードに固定する 2 本のネジ(M2x3)を取り付けます。 12.
7. WWAN カードを取り外します。 8. ディスプレイ アセンブリーを取り外します。 このタスクについて 次の画像はディスプレイ ベゼルの位置を示すもので、取り外し手順を視覚的に表しています。 手順 メモ: ディスプレイ ベゼルは、粘着テープでモニター パネルに取り付けられています。プラスチック スクライブを両方のヒン ジ キャップ付近のくぼみに挿入し、この位置からディスプレイ ベゼルをこじ開けます。ディスプレイ ベゼルの外側の端に沿 ってこじ開け、ディスプレイ ベゼルがディスプレイ カバーから外れるまでディスプレイ ベゼルの周り全体を外していきます。 注意: モニター パネル損傷のリスクを最小限にするために、ディスプレイ ベゼルを慎重に持ち上げて取り外します。 1. プラスチック スクライブを両方のヒンジ キャップ付近のくぼみに挿入し、この位置からディスプレイ ベゼルをこじ開けます。 2. ディスプレイ ベゼルの外側の端に沿ってこじ開け、ディスプレイ ベゼルがディスプレイ カバーから外れるまでディスプレイ ベゼルの周り全体を外していきます。 3.
手順 1. 位置を合わせてディスプレイ ベゼルをディスプレイ アセンブリーにセットします。 2. ディスプレイ ベゼルを慎重に所定の位置へはめ込みます。 次の手順 1. ディスプレイ アセンブリーを取り付けます。 2. WWAN カードを取り付けます。 3. WLAN カードを取り付けます。 4. ベース カバーを取り付けます。 5. microSD カードを取り付けます。 6. SIM カードを取り付けます。 7. サービス モードを終了します。 8. 「PC 内部の作業を終えた後に」の手順に従います。 ディスプレイパネル モニター パネルの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. WLAN カードを取り外します。 7. WWAN カードを取り外します。 8. ディスプレイ アセンブリーを取り外します。 9.
このタスクについて 次の画像はモニター パネルの位置を示すもので、取り外し手順を視覚的に表しています。 コンポーネントの取り外しと取り付け 77
コンポーネントの取り外しと取り付け
手順 メモ: モニター パネルは、1 個のサービス パーツとしてディスプレイ ブラケットと一緒に事前に組み立てられています。スト レッチ リリース(SR)テープを引き出さないでください。また、ブラケットをモニター パネルから分離することはできませ ん。 1. モニター パネルをディスプレイ背面カバーに固定している 4 本のネジ(M2.5x3.5)を外します。 メモ: モニター パネルを取り外す時には、モニター パネルのタブをディスプレイ カバーから外した後に、モニター パネル を裏返してください。 2. モニター パネルを持ち上げて開き、モニター ケーブルを取り出せるようにします。 3. モニター ケーブル コネクタの導電テープをはがします。 4. モニター ケーブル コネクターを覆っている透明なテープをはがします。 5. ラッチを開いて、モニター パネルのコネクターからケーブルを外します。 6.
コンポーネントの取り外しと取り付け
手順 1. モニター ケーブルをモニター パネルのコネクタに接続し、ラッチを閉じます。 2. 透明なテープを貼り付けてモニター ケーブル コネクターを覆います。 3. 導電テープを貼り付けてモニター ケーブルをモニター パネルに固定します。 4. モニター パネルを閉じてディスプレイ背面カバーと合わせます。 メモ: モニター パネルのタブがディスプレイ カバーのスロットに挿入されていることを確認してください。 5. モニター パネルをディスプレイ背面カバーに固定する 4 本のネジ(M2.5x3.5)を取り付けます。 次の手順 1. ディスプレイ ベゼルを取り付けます。 2. ディスプレイ アセンブリーを取り付けます。 3. WWAN カードを取り付けます。 4. WLAN カードを取り付けます。 5. ベース カバーを取り付けます。 6. microSD カードを取り付けます。 7. SIM カードを取り付けます。 8. サービス モードを終了します。 9.
カメラ/マイクロフォン モジュール カメラの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. ディスプレイ アセンブリーを取り外します。 7. ディスプレイ ベゼルを取り外します。 8. モニター パネルを取り外します。 9. ディスプレイヒンジを取り外します。 このタスクについて 次の画像はカメラ モジュールの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. カメラ ケーブルを固定しているテープをはがします。 メモ: 雑にはがしてしまうと、ディスプレイ ベゼルからカメラ用シャッターが外れたり、カメラ用シャッターが損傷したり する可能性があります。 2. ラッチを持ち上げて、カメラ モジュールのコネクターからカメラ ケーブルを外します。 3. カメラ モジュールの一番下の端にある持ち上げポイントから、カメラ モジュールを慎重にこじ開けます。 4.
このタスクについて 以下の画像はカメラの位置を示すもので、取り付け手順を視覚的に表しています。 手順 1. カメラ モジュールをディスプレイ背面カバーのスロットに合わせて配置します。 2. カメラケーブルをカメラモジュールのコネクタに接続します。 3. テープを貼り付けて、カメラ ケーブルを所定の位置に固定します。 次の手順 1. ディスプレイ ヒンジを取り付けます。 2. モニター パネルを取り付けます。 3. ディスプレイ ベゼルを取り付けます。 4. ディスプレイ アセンブリーを取り付けます。 5. ベース カバーを取り付けます。 6. microSD カードを取り付けます。 7. SIM カードを取り付けます。 8. サービス モードを終了します。 9. 「PC 内部の作業を終えた後に」の手順に従います。 eDP/モニター ケーブル eDP ケーブルの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6.
このタスクについて 次の画像は、eDP ケーブルの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. eDP/モニター ケーブルをカメラ/マイクロフォン モジュールのコネクターから外します。 2.
手順 1. eDP/モニター ケーブルをカメラのコネクターに接続します。 2. eDP/モニター ケーブルをディスプレイ背面カバーに貼り付けます。 3. ディスプレイ背面カバーに導電テープを貼り付け、eDP/モニター ケーブルを配線します。 次の手順 1. モニター パネルを取り付けます。 2. ディスプレイ ベゼルを取り付けます。 3. ディスプレイ アセンブリーを取り付けます。 4. WWAN カードを取り付けます。 5. WLAN カードを取り付けます。 6. ベース カバーを取り付けます。 7. microSD カードを取り付けます。 8. SIM カードを取り付けます。 9. サービス モードを終了します。 10.
センサーボード センサー ボードの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. WLAN カードを取り外します。 7. WWAN カードを取り外します。 8. ディスプレイ アセンブリーを取り外します。 9. ディスプレイ ベゼルを取り外します。 10. モニター パネルを取り外します。 このタスクについて メモ: この手順はセンサー ボードが搭載されている PC にのみ適用されます。 次の画像はセンサー ボードの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. ラッチを開いて、LED ケーブルをセンサー ボードのコネクターから外します。 2.
手順 1. センサー ボードをディスプレイ背面カバーに合わせて配置します。 2. LED ケーブルをセンサー ボードのコネクターに接続し、ラッチを閉じます。 次の手順 1. モニター パネルを取り付けます。 2. ディスプレイ ベゼルを取り付けます。 3. ディスプレイ アセンブリーを取り付けます。 4. WWAN カードを取り付けます。 5. WLAN カードを取り付けます。 6. ベース カバーを取り付けます。 7. microSD カードを取り付けます。 8. SIM カードを取り付けます。 9. サービス モードを終了します。 10.「PC 内部の作業を終えた後に」の手順に従います。 ディスプレイ ヒンジ ディスプレイ ヒンジの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. WLAN カードを取り外します。 7. WWAN カードを取り外します。 8. ディスプレイ アセンブリーを取り外します。 9.
このタスクについて 次の画像はディスプレイ ヒンジの位置を示すもので、取り外し手順を視覚的に表しています。 手順 1. 右のヒンジをディスプレイ背面カバーに固定している 1 本のネジ(M2.5x3.5)を外します。 2. 右のヒンジを持ち上げて、ディスプレイ背面カバーから取り外します。 3. 左のヒンジをディスプレイ背面カバーに固定している 1 本のネジ(M2.5x3.5)を外します。 4.
手順 1. 左のヒンジのネジ穴をディスプレイ背面カバーのネジ穴に合わせます。 2. 1 本のネジ(M2.5x3.5)を取り付けて、左のヒンジをディスプレイ背面カバーに固定します。 3. 右のヒンジのネジ穴をディスプレイ背面カバーのネジ穴に合わせます。 4. 1 本のネジ(M2.5x3.5)を取り付けて、右のヒンジをディスプレイ背面カバーに固定します。 次の手順 1. モニター パネルを取り付けます。 2. ディスプレイ ベゼルを取り付けます。 3. ディスプレイ アセンブリーを取り付けます。 4. WWAN カードを取り付けます。 5. WLAN カードを取り付けます。 6. ベース カバーを取り付けます。 7. microSD カードを取り付けます。 8. SIM カードを取り付けます。 9. サービス モードを終了します。 10.
ディスプレイ背面カバー ディスプレイ背面カバーの取り外し 前提条件 1. 「PC 内部の作業を始める前に」の手順に従います。 2. サービス モードを起動します。 3. SIM カードを取り外します。 4. microSD カードを取り外します。 5. ベース カバーを取り外します。 6. WLAN カードを取り外します。 7. WWAN カードを取り外します。 8. ディスプレイ アセンブリーを取り外します。 9. ディスプレイ ベゼルを取り外します。 10. モニター パネルを取り外します。 11. カメラ/マイクロフォン モジュールを取り外します。 12. eDP/モニター ケーブルを取り外します。 13. センサーボードを取り外します。 14.
このタスクについて 次の画像はディスプレイ背面カバーの位置を示すもので、取り付け手順を視覚的に表しています。 手順 ディスプレイ背面カバーを平らな場所に置きます。 次の手順 1. ディスプレイ ヒンジを取り付けます。 2. センサー ボードを取り付けます。 3. eDP/モニター ケーブルを取り付けます。 4. カメラ/マイクロフォン モジュールを取り付けます。 5. モニター パネルを取り付けます。 6. ディスプレイ ベゼルを取り付けます。 7. ディスプレイ アセンブリーを取り付けます。 8. WWAN カードを取り付けます。 9. WLAN カードを取り付けます。 10. ベース カバーを取り付けます。 11. microSD カードを取り付けます。 12. SIM カードを取り付けます。 13. サービス モードを終了します。 14.「PC 内部の作業を終えた後に」の手順に従います。 パームレスト アセンブリー パームレスト アセンブリーの取り外し 前提条件 1. 2. 3. 4.
5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
このタスクについて 次のイメージは、パームレスト アセンブリーの場所を示すもので、取り付け手順を視覚的に表しています。 手順 1. パームレストアセンブリーを平らな面に置きます。 2. 非 WWAN LTE 構成用のダミー SIM カード フィラーを取り外します。 次の手順 1. ディスプレイ アセンブリーを取り付けます。 2. キーボードアセンブリー を取り付けます。 3. スマート カード リーダーを取り付けます。 4. LED ボードを取り付けます。 5. 電源ボタン ボードを取り付けます。 6. システム ボードを取り付けます。 7. アセンブリー内部フレームを取り付けます。 8. スピーカーを取り付けます。 9. システム構成に基づいて、UMA または専用ヒート シンクを取り付けます。 10. バッテリーを取り付けます。 11. WWAN カードを取り付けます。 12. WLAN カードを取り付けます。 13. 2280 ソリッドステート ドライブまたは 2230 ソリッドステート ドライブを取り付けます。 14. メモリ モジュールを取り付けます。 15. ベース カバーを取り付けます。 16.
3 ドライバおよびダウンロード この章では、サポート対象のオペレーティング システムとドライバーのインストール方法を説明します。 トピック: • ドライバーのダウンロード ドライバーのダウンロード 手順 1. PC の電源を入れます。 2. www.dell.com/support にアクセスします。 3. お使いの PC のサービス タグを入力して、[Submit(送信)] をクリックします。 メモ: サービス タグがない場合は、自動検出機能を使用するか、お使いの PC のモデルを手動で参照してください。 4. [Drivers & Downloads(ドライバーとダウンロード)]をクリックします。 5. [Detect Drivers(ドライバーの検出)] ボタンをクリックします。 6. [SupportAssist] の利用規約を確認のうえ同意し、[Continue(続ける)] をクリックします。 7. 必要に応じて、お使いの PC が [SupportAssist] のダウンロードとインストールを開始します。 メモ: ブラウザー固有の手順については画面の指示を確認してください。 8.
4 セットアップユーティリティ 注意: コンピューターに詳しい方以外は、BIOS セットアップ プログラムの設定を変更しないでください。特定の変更でコンピ ュータが誤作動を起こす可能性があります。 メモ: BIOS セットアップ プログラムを変更する前に、後で参照できるように、BIOS セットアップ プログラム画面の情報を控 えておくことをお勧めします。 BIOS セットアップ プログラムは次の目的で使用します。 ● RAM の容量やハード ドライブのサイズなど、コンピューターに取り付けられているハードウェアに関する情報の取得。 ● システム設定情報の変更。 ● ユーザー パスワード、取り付けられたハード ドライブの種類、基本デバイスの有効化または無効化など、ユーザー選択可能オ プションの設定または変更。 トピック: • • • • • • • • • BIOS の概要 BIOS セットアッププログラムの起動 ナビゲーションキー ブート シーケンス 高度な設定またはエンジニアリング設定 SupportAssist システムの解決策 システム セットアップのオプション Windows での BIOS のアッ
キー ナビゲーション メイン画面が表示されるまで、前のページに戻ります。メイン画面で Esc を押すと、未保存の変更の保存を 促すメッセージが表示され、システムが再起動します。 ブート シーケンス ブート シーケンスを利用すると、セットアップ ユーティリティで定義されたデバイス起動順序をバイパスし、特定のデバイス(例: 光学ドライブまたはハード ドライブ)から直接起動することができます。電源投入時の自己テスト(POST)中に Dell のロゴが表 示されたら、以下が可能になります。 ● F2 キーを押してセットアップ ユーティリティにアクセスする ● F12 キーを押してワンタイム ブート メニューを立ち上げる ワンタイム ブート メニューでは診断オプションを含むオプションから起動可能なデバイスを表示します。起動メニューのオプシ ョンは以下のとおりです。 ● ● ● ● ● Windows ブートマネージャー UEFI HTTPS 起動 UEFI RST Micron 2300 NVMe 512 GB 20502C1A4567 オンボード NIC(IPv4) オンボード NIC(IPv6
システム セットアップのオプション メモ: お使いの PC および取り付けられているデバイスによっては、このセクションに記載されている項目の一部が表示されな い場合があります。 表 6.
表 6.
表 8.
表 8. システム セットアップのオプション:内蔵デバイス メニュー (続き) 内蔵デバイス Enable Unobtrusive Mode(Unobtrusive Mode を有効にする) PC のすべてのライトとサウンドを有効または無効にします。 デフォルトでは、[控えめモードを有効にする]オプションは無効になっていま す。 表 9. システム セットアップのオプション:ストレージ メニュー ストレージ [SMART レポート] Enable SMART Reporting(SMART レポート PC 起動中の Self-Monitoring, Analysis, and Reporting Technology(SMART)を有効 を有効にする) または無効にします。 デフォルトでは、 [SMART レポートを有効にする]オプションは無効になってい ます。 [ドライブ情報] [SATA-1] タイプ PC の SATA-1 タイプ情報を表示します。 デバイス コンピュータの SATA-1 デバイス情報を表示します。 [M.2 PCIe SSD-1] タイプ PC の M.
表 11.
表 12.
表 13.
表 14.
表 16.
表 18. システム セットアップのオプション:起動前の作動メニュー (続き) 起動前作動 [警告およびエラー] 警告またはエラーが発生した場合に実行するアクションを有効または無効にし ます。 デフォルトでは、[警告とエラー時のプロンプト]オプションは有効になってい ます。 [ファストブート] 起動プロセスのスピードを設定できます。 デフォルトでは、[最短]オプションが有効になっています。 [BIOS POST 時間の延長] BIOS の POST 時間を設定します。 デフォルトでは、[0 秒]オプションが有効になっています。 [MAC Address Pass- Through] 外部の NIC MAC アドレスを PC から選択した MAC アドレスに置き換えます。 デフォルトでは、 [システム特有の MAC アドレス]オプションが有効になってい ます。 表 19.
表 20.
BitLocker が有効なシステムでの BIOS のアップデート 注意: BitLocker を一時停止せずに BIOS をアップデートすると、次回システムを再起動した際、BitLocker キーが認識されま せん。その後、続行するためにはリカバリー キーの入力を求められ、これは再起動のたびに要求されるようになります。リカ バリー キーが不明な場合は、データ ロスの原因となったり、本来必要のないオペレーティング システムの再インストールが 必要になったりする可能性があります。この件の詳細については、ナレッジベース記事を参照してください。 「BitLocker が有 効になっている Dell システムでの BIOS のアップデート(英語)」https://www.dell.
手順 1. [システム BIOS]画面または[システム セットアップ]画面で、[セキュリティ]を選択し、Enter を押します。 [セキュリティ]画面が表示されます。 2. [システム/管理者パスワード]を選択し、[新しいパスワードを入力]フィールドでパスワードを作成します。 以下のガイドラインに従ってシステムパスワードを設定します。 ● パスワードの文字数は 32 文字までです。 ● 0 から 9 までの数字を含めることができます。 ● 小文字のみ有効です。大文字は使用できません。 ● 特殊文字は、次の文字のみが利用可能です:スペース、(”)、(+)、(,)、(-)、(.)、(/)、(;)、([)、(\)、(])、(`)。 3. [新しいパスワードの確認]フィールドで以前入力したシステムパスワードを入力し、[OK] をクリックします。 4. Esc を押すと、変更の保存を求めるメッセージが表示されます。 5.
5 トラブルシューティング トピック: Dell SupportAssist 起動前システム パフォーマンス チェック診断 システム診断ライト オペレーティング システムのリカバリー BIOS のフラッシュ(USB キー) BIOS のフラッシュ Wi-Fi 電源の入れ直し 待機電力の放出 • • • • • • • Dell SupportAssist 起動前システム パフォーマンス チェ ック診断 このタスクについて SupportAssist 診断(システム診断とも呼ばれる)ではハードウェアの完全なチェックを実行します。Dell SupportAssist 起動前シス テム パフォーマンス チェック診断は BIOS に組み込まれており、BIOS によって内部で起動します。組み込み型システム診断プロ グラムには、特定のデバイスまたはデバイス グループ用の一連のオプションが用意されており、以下の処理が可能です。 ● テストを自動的に、または対話モードで実行 ● テストの繰り返し ● テスト結果の表示または保存 ● 詳細なテストで追加のテストオプションを実行し、障害の発生したデバイスに関する詳しい情報を得
システム診断ライト バッテリーステータスライト 電源およびバッテリー充電ステータスを示します。 ソリッド ホワイト:電源アダプターが接続され、バッテリーの充電量は 5% 以上です。 橙色 — コンピュータがバッテリーで動作しており、バッテリーの充電量は 5% 未満です。 消灯 ● 電源アダプターが接続されバッテリーがフル充電されています。 ● PC がバッテリーで動作しており、バッテリーの充電量が 5% 以上です。 ● PC がスリープ状態、休止状態、または電源オフです。 電源およびバッテリーステータスライトが障害を示すビープコードと合わせて橙色に点滅します。 例えば、電源およびバッテリーステータスライトが、橙色に 2 回点滅して停止し、次に白色に 3 回点滅して停止します。この 2,3 のパターンは、PC の電源が切れるまで続き、メモリーまたは RAM が検出されないことを示しています。 次の表には、さまざまな電源およびバッテリーステータスライトのパターンと関連する問題が記載されています。 点滅パターン 問題の内容 推奨される処置 1 1 TPM 検出エラー システム ボードを取り付けま す。
点滅パターン 問題の内容 推奨される処置 LCD コントローラモジュール を交換してください。 2 7 LCD の障害(SBIOS メッセー ジ) 2 8 LCD の障害(母線の障害が EC システム ボードを取り付けま で検出) す。 3 1 CMOS バッテリーの障害です 3 2 PCI またはビデオ カード/チッ システム ボードを取り付けま プの障害です す。 3 3 BIOS のリカバリイメージが見 つかりません 3 4 検出された BIOS のリカバリイ BIOS の最新バージョンをフラ メージは無効です ッシュします。問題が解決し ない場合は、システム ボード を交換します。 3 5 母線の障害です システム ボードを取り付けま す。 3 6 SBIOS によってフラッシュの 破損が検出されました。 システム ボードを取り付けま す。 3 7 ME が HECI メッセージへの返 信を待機している間にタイム アウトしました。 システム ボードを取り付けま す。 CMOS バッテリー接続をリセ ットします。問題が解決しな い場合は、
2. 起動可能な USB ドライブを作成します。詳細については、www.dell.com/support でナレッジ ベース記事 000145519 を参照して ください。 3. BIOS セットアップ プログラム ファイルを起動可能な USB ドライブにコピーします。 4. 起動可能な USB ドライブを BIOS のアップデートを必要とするコンピューターに接続します。 5. コンピュータを再起動し、Dell のロゴが画面に表示されたら F12 を押します。 6. ワン タイム ブート メニューから USB ドライブを起動します。 7. BIOS セットアップ プログラムのファイル名を入力し、Enter を押します。 8. BIOS アップデート ユーティリティが表示されます。画面の指示に従って、BIOS のアップデートを完了します。 BIOS のフラッシュ このタスクについて 更新がある場合やシステム ボードを取り付ける場合に、BIOS のフラッシュ(更新)を行う必要があります。 次の手順に従って BIOS をフラッシュします。 手順 1. PC の電源を入れます。 2. www.dell.
待機電力の放出 このタスクについて 待機電力とは、コンピュータの電源をオフにしてバッテリを取り外した後もコンピュータに残っている余分な静電気のことを指し ます。次の手順は、待機電力の放出方法を説明したものです。 手順 1. コンピュータの電源を切ります。 2. 電源アダプタをコンピュータから外します。 3. 電源ボタンを 15 秒間長押しして、待機電力を逃がします。 4. 電源アダプタをコンピュータに接続します。 5.
6 ヘルプ トピック: Dell へのお問い合わせ • Dell へのお問い合わせ 前提条件 メモ: インターネットにアクセスできない場合には、注文書、配送伝票、請求書、または Dell 製品カタログにある、お問い合 わせ情報をご利用ください。 このタスクについて Dell では、オンラインおよび電話によるサポートとサービスオプションをいくつかご用意しています。これらのサービスは国およ び製品によって異なり、お住まいの地域では一部のサービスがご利用いただけない場合があります。Dell のセールス、テクニカル サポート、またはカスタマー サービスへは、次の手順でお問い合わせいただけます。 手順 1. [Dell.com/support] にアクセスしてください。 2. サポートカテゴリを選択します。 3. ページの下部にある [国 / 地域の選択] ドロップダウンリストで、お住まいの国または地域を確認します。 4.