Dell Latitude 12 Rugged Tablet – 7202 Getting Started Guide Guide de mise en route Handleiding Aan de slag Handbuch zum Einstieg Guida introduttiva Regulatory Model: T03H Regulatory Type: T03H001
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 Finding Information and Resources.................................................................. 4 2 Front and Back View.............................................................................................5 3 Quick Setup............................................................................................................7 4 Removing and Installing Components............................................................. 9 Removing the Battery........................................
Finding Information and Resources See the safety and regulatory documents that shipped with your computer and the regulatory compliance website at www.dell.com/regulatory_compliance for more information on: • Safety best practices • Regulatory certification • Ergonomics See www.dell.com for additional information on: • Warranty • Terms and Conditions (U.S. only) • End User License Agreement Additional information on your product is available at www.dell.
Front and Back View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 2 Microphone Camera status light Camera Camera shutter switch Ambient light sensor Stylus Power button Micro serial port USB 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
Quick Setup 3 WARNING: Before you begin any of the procedures in this section, read the safety information that shipped with your computer. For additional best practices information, see www.dell.com/ regulatory_compliance WARNING: The AC adapter works with electrical outlets worldwide. However, power connectors and power strips vary among countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause fire or equipment damage.
Removing and Installing Components 4 This section provides detailed information on how to remove or install the components from your computer. Removing the Battery WARNING: Using an incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell. The battery is designed to work with your Dell tablet. Do not use a battery from any other tablet with your tablet.
Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Lock the battery by sliding the latch away from it. Installing the SIM Card NOTE: The SIM card slot is located underneath the battery 2 slot. 1. Remove the battery. 2. To install the SIM card: a. Press the SIM latch and pull it in an outward direction. b. Insert the SIM card into the slot. c. Push the SIM release latch inwards to lock it. 3. Install the battery into the battery bay. 4.
Dell Rugged Control Center Application 5 The Dell Rugged Control Center (RCC) is an application designed for your Dell Latitude 12 Rugged Tablet, which enables you to perform several important tasks on the tablet. After you install the Dell Rugged Control Center application on your tablet, you can view all the basic features, such as Wi-Fi, Bluetooth, camera, volume, brightness, and so on. In addition, this application also enables you to add a shortcut of any feature onto it.
Feature Description Allows you to enable or disable the WWAN / Mobile broadband service (if configured). Allows you to enable or disable Bluetooth. Allows you to turn on or off the built-in flashlight. Allows you to enable or disable the Automatic Light Sensor. Launches the camera application. Launches the GPS control panel, which allows you to enable or disable the GPS. If you enable the GPS, the control panel will also show your current location, along with the time, date, latitude, and longitude.
Using the Settings Option in Rugged Control Center You can also touch the options. option from the top-right corner of the RCC application to explore more The following table shows the feature description available in the Settings option of the RCC Application: Feature Description Launches the Windows control panel for pen and touch settings. NOTE: This option is compatible only if you have the optional keyboard accessory for your tablet.
Feature Description Launches a control panel to assign actions to the 3 programmable buttons on the front of the tablet. Launches the Windows control panel for battery settings. Launches the Windows control panel. Launches the control panel to adjust settings of the RCC application. Installing the Dell Rugged Control Center NOTE: 1. • Dell Rugged Control Center is compatible only with Windows 8 or higher versions of operating systems.
Enabling or Disabling the Keyboard Backlight NOTE: This feature can be used only if the tablet is connected to an external keyboard accessory (sold separately). 1. Launch the Rugged Control Center application. 2. Press the Settings 3. Press the Backlit Keyboard button 4. Adjust the required parameters for Backlight settings and Backlight colors. button on the top-right corner. to access the Backlit Keyboard control panel. Changing the Keyboard Backlight Colors 1.
6 Stealth Mode Latitude fully rugged products come equipped with a Stealth mode. Stealth mode allows you to turn off the Display, all the LED lights, internal speakers, the fan and all wireless radios with a single key combination. NOTE: This mode is aimed at using the tablet in covert operations. When the stealth mode is activated, the tablet remains functional but will not emit any light or sound.
3. Set any 3 programmable buttons to enable or disable the Stealth Mode. 4. Use the selected programmable buttons to enable or disable the Stealth Mode. Modifying the Stealth Mode Settings You can also modify your desired features to disable in the stealth mode settings. To modify the stealth mode settings: 1. Launch the Rugged Control Center application on your tablet. 2. From the main screen, press the Settings button 3. Select the features that you want to disable in the stealth mode.
Enabling and Disabling Wireless (WiFi) Feature 7 You can enable or disable the wireless (Wi-Fi) feature, using the optional keyboard accessory and using the programmable buttons in RCC application. NOTE: WiFi can also be enabled/disabled by using the user defined programmable buttons on the tablet. Enabling or Disabling Wireless (WI-Fi) Feature Using Optional Keyboard Accessory 1. Press the + keys to enable wireless feature. 2.
5. Use the programmed button to Enable/Disable Wireless networks on the tablet.
Smart Cards 8 There are two main types of Smart or Common Access Cards (CAC): 1. Enclosed Smart Cards — These cards have a contact area with many gold plated connection pads. When inserted into a card reader, the information from the chip can be read and written Insert the card into the smart card slot with the gold contact pad facing upward and pointing toward the smart card slot. Slide the card into the slot until it is fully seated in its connector. 2.
9 Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view information about your computer.
Communications Network adapter WLAN, LTE, HSPA+ Wireless BT, NFC • Bluetooth 4.0 LE NOTE: The optional I/O expansion module, if purchased with the tablet, comes equipped with an additional Network port (Ethernet). Ports and Connectors Audio one 3.5 mm jack Video one mini HDMI connector USB one USB 3.
Display Feature Specification Minimum viewing angles: Horizontal • • +/- 40° for HD +/- 60° for FHD Vertical • • +10°/-30° for HD +/-50° for FHD Pixel pitch 0.2265 mm Front camera Type OV 2724 (2 MP) Resolution 1366 x 768 pixels Rear camera Type IMX 134 (8 MP) Resolution 3264 pixels x 2448 pixels Storage Storage M.2 SSD 128 GB / 256 GB / 512 GB Battery Type 2-cell lithium ion (26 WHr) Dimensions Length 103.60 mm (4.08 inches) Height 15.00 mm (0.59 inch) Width 62.70 mm (2.
AC Adapter Input current (maximum) 0.60 A Input frequency 50 Hz to 60 Hz Output power 45 W Output current (45 W) 2.31 A Rated output voltage 19.5 VDC Temperature range: Operating 0 °C to 40 °C (32 °F to 104 °F) Non-operating –40 °C to 70 °C (–40 °F to 158 °F) Physical Typical Width 312.20 mm (12.29 inches) Height 203.00 mm (7.99 inches) Thickness 24.40 mm (0.96 inch) Maximum Width 318.20 mm (12.53 inches) Height 209.00 mm (8.23 inches) Thickness 28.90 mm (1.
Contacting Dell 10 NOTE: If you do not have an active Internet connection, you can find the contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: Go to dell.com/contactdell.
Tablette durcie Dell Latitude 12 – 7202 Guide de mise en route Modèle réglementaire: T03H Type réglementaire: T03H001
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION indique un risque d'endommagement du matériel ou de perte de données et vous indique comment éviter le problème. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessures corporelles ou même de mort. Copyright © 2015 Dell Inc. Tous droits réservés.
Table des matières 1 Où trouver des informations et des ressources supplémentaires............... 4 2 Vues avant et arrière.............................................................................................5 3 Installation et configuration rapides................................................................. 7 4 Retrait et installation des composants............................................................. 9 Retrait de la batterie.............................................................
Où trouver des informations et des ressources supplémentaires 1 Consultez les documents réglementaires et de sécurité livrés avec votre ordinateur et la page Regulatory Compliance (Conformité à la réglementation) à l'adresse www.dell.com/regulatory_compliance pour plus d'informations sur : • Les meilleures pratiques en matière de sécurité • La certification réglementaire • L'ergonomie Consultez le site www.dell.
Vues avant et arrière 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 2 Microphone Voyant d'état de la caméra Caméra Obturateur de l'appareil photo Capteur de lumière ambiante Stylet Bouton d'alimentation Port série micro Connecteur USB 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
Installation et configuration rapides 3 AVERTISSEMENT : vant de commencer à appliquer toute procédure expliquée dans cette section, prenez connaissance des consignes de sécurité fournies avec votre ordinateur. Pour plus d’informations sur les meilleures pratiques, consultez le site www.dell.com/ regulatory_compliance AVERTISSEMENT : L’adaptateur secteur fonctionne avec les prises électriques du monde entier. Mais les connecteurs et les barrettes d’alimentation varient d’un pays à l’autre.
REMARQUE : Il est recommandé d’allumer et d’éteindre l’ordinateur au moins une fois avant d’installer des cartes ou de connecter l’ordinateur à une station d’accueil ou un autre périphérique externe tel qu’une imprimante.
Retrait et installation des composants 4 Cette section fournit des informations détaillées sur le retrait ou l'installation des composants de l'ordinateur. Retrait de la batterie AVERTISSEMENT : L’utilisation d’une batterie non compatible peut accroître le risque d’incendie ou d’explosion. Remplacez la batterie uniquement par une batterie compatible achetée auprès de Dell. La batterie est conçue pour fonctionner avec votre tablette Dell.
Installation de la batterie 1. Faites glisser la batterie dans son emplacement jusqu’à ce que vous l’entendiez s’enclencher. 2. Verrouillez la batterie en faisant glisser le loquet tout en l'éloignant de celle-ci. Installation de la carte SIM REMARQUE : Le logement de la carte SIM est situé en-dessous du compartiment de la batterie 2. 1. Retirez la batterie. 2. Pour installer la carte SIM : a. Appuyez sur le loquet de la carte SIM puis tirez-le en exerçant un mouvement vers l'extérieur. b.
Application Rugged Control Center de Dell. 5 Le Rugged Control Center (RCC) de Dell est une application conçue pour votre tablette durcie Latitude 12 de Dell, qui vous permet d'effectuer plusieurs tâches importantes sur la tablette. Après avoir installé l'application Rugged Control Center de Dell sur votre tablette, vous pouvez visualiser toutes les fonctionnalités de base, telles que le Wi-Fi, le Bluetooth, l’appareil photo, le volume, la luminosité et ainsi de suite.
Fonction Description REMARQUE : Pour vous connecter au WLAN, assurez-vous que votre réseau soit configuré. Vous permet d’activer ou de désactiver le mode WWAN / service mobile à large bande (si configuré). Vous permet d'activer ou de désactiver le Bluetooth. Vous permet d'allumer ou d'éteindre la lampe de poche intégrée. Vous permet d'activer ou de désactiver l'émulation WWAN. Lance l'application de l’appareil photo. Lance le panneau de commande GPS, qui vous permet d'activer ou de désactiver le GPS.
Utiliser l'option Paramètres dans l'application Rugged Control Center Vous pouvez également toucher d’explorer davantage d'options. option depuis le coin supérieur droit de l'application RCC afin Le tableau suivant montre la description de la fonctionnalité disponible dans l'option Paramètres de l'application RCC : Fonction Description Lance le panneau de configuration Windows pour les paramètres d’utilisation avec stylet et tactile.
Fonction Description Lance un panneau de configuration afin d’attribuer des actions aux 3 touches programmables situées sur le devant de la tablette. Lance le panneau de configuration Windows pour les paramètres de la batterie. Lance le panneau de configuration de Windows. Lance le panneau de configuration afin d'ajuster les paramètres de l'application RCC. Installation du Rugged Control Center de Dell REMARQUE : 1.
Activation ou désactivation du rétroéclairage clavier REMARQUE : Cette fonctionnalité peut être utilisée uniquement si la tablette est connectée à un accessoire clavier externe (vendu séparément). 1. Lancez l'application Rugged Control Center. 2. Appuyez sur Réglages 3. Appuyez sur le bouton Clavier rétroéclairé rétroéclairé. 4. Ajustez les paramètres requis pour les réglages et les couleurs du rétroéclairage. bouton dans le coin supérieur droit.
2.
Mode Stealth 6 Les produits tout terrain Latitude sont équipés d’un mode Stealth. Le mode Stealth vous permet d’éteindre l’écran, tous les voyants LED, les haut-parleurs internes, le ventilateur et les communications sans fil avec une seule combinaison de touches. REMARQUE : Ce mode est destiné à utiliser la tablette dans des opérations de couverture. Lorsque le mode furtif est activé, l’ordinateur continue de fonctionner, mais n’émet pas de lumière ou d'audio.
Mettre en marche et arrêter le mode furtif en utilisant le RCC 1. Lancez l'application Rugged Control Center sur votre tablette. 2. À partir de l'écran principal, appuyez sur le bouton Réglages 3. Définissez 3 touches programmables afin d'activer ou de désactiver le mode furtif. 4. Utilisez les touches programmables sélectionnées afin d’activer ou de désactiver le mode furtif. > Touches programmables.
7 Activation et désactivation de la fonction sans fil (WiFi) Vous pouvez activer ou désactiver la fonction de sans fil (Wi-Fi) en utilisant l'accessoire clavier en option et les touches programmables dans l'application RCC. REMARQUE : La WiFi peut également être activée/désactivée en utilisant les touches programmables définies par l'utilisateur sur la tablette. Activer ou désactiver la fonctionnalité sans fil (WI-Fi) avec l'accessoire clavier en option 1.
5. 20 Utilisez la touche programmée pour activer/désactiver les réseaux sans fil sur la tablette.
Cartes à puce 8 Il existe deux types principaux de cartes à puce ou de cartes d'accès commune (CAC) : 1. Cartes à puce jointes : ces cartes ont une zone de contact avec de nombreux points de connexion en or plaqué. Lorsqu’elles sont insérées dans un lecteur de carte, les informations peuvent aisément être lues et écrites Insérez la carte dans le logement de carte à puce avec le point de contact métallique face vers le haut pointant vers le logement de carte à puce.
Caractéristiques 9 REMARQUE : Les offres proposées peuvent varier selon les pays. Les caractéristiques qui suivent se limitent à celles que la législation impose de fournir avec l'ordinateur. Pour plus d'informations concernant la configuration de votre ordinateur, cliquez sur Aide et support dans votre système d'exploitation Windows, puis sélectionnez l'option qui permet d'afficher les informations relatives à votre ordinateur.
Communications Carte réseau WLAN, LTE, HSPA+ Sans fil Bluetooth, NFC • Bluetooth 4.0 LE REMARQUE : Le module d'extension I/O en option, si acheté avec la tablette, est livré avec un port réseau supplémentaire (Ethernet). Ports et connecteurs Audio Une prise jack de 3,5 mm Vidéo un connecteur mini HDMI USB Un connecteur USB 3.
Écran Fonction Spécification Fréquence de rafraîchissement 60 Hz Angles minimums de visualisation : Horizontal • • +/- 40° pour la HD +/- 60° pour la FHD Vertical • • +10°/-30° pour la HD +/- 50° pour la FHD Pas de pixel 0,2265 mm Caméra avant Type OV 2724 (2 MP) Résolution 1366 x 768 pixels Caméra arrière Type IMX 134 (8 MP) Résolution 3264 × 2448 pixels Stockage Stockage M.
Adaptateur secteur Type Tension d’entrée de 100 VCA à 240 VCA Courant d’entrée (maximal) 0,60 A Fréquence en entrée 50 Hz à 60 Hz Puissance de sortie 45 W Courant de sortie (45 W) 2,31 A Tension de sortie nominale 19,5 VCC Plage de températures : En fonctionnement de 0 °C à 40 °C (de 32 °F à 104 °F) Hors fonctionnement de –40° C à 70° C (de –40° F à 158° F) Caractéristiques physiques Par défaut Largeur 312,20 mm (12,29 pouces) Hauteur 203,00 mm (7,99 pouces) Profondeur 24,40 mm (0,96 po
26
Contacter Dell 10 REMARQUE : Si vous ne disposez pas d'une connexion Internet, les informations de contact figurent sur la facture d'achat, le borderau de colisage, la facture le catalogue des produits Dell. Dell propose diverses options d'assistance et de maintenance en ligne et téléphonique. Ces options varient en fonction du pays et du produit et certains services peuvent ne pas être disponibles dans votre région Pour contacter le service commercial, technique ou client de Dell : Rendez-vous sur dell.
Dell Latitude 12 Rugged Tablet – 7202 Handleiding Aan de slag Regelgevingsmodel: T03H Regelgevingstype: T03H001
Opmerkingen, voorzorgsmaatregelen,en waarschuwingen OPMERKING: Een OPMERKING duidt belangrijke informatie aan voor een beter gebruik van de computer. WAARSCHUWING: EEN WAARSCHUWING duidt potentiële schade aan hardware of potentieel gegevensverlies aan en vertelt u hoe het probleem kan worden vermeden. GEVAAR: Een GEVAAR-KENNISGEVING duidt op een risico op schade aan eigendommen, lichamelijk letsel of overlijden. Copyright © 2015 Dell Inc. Alle rechten voorbehouden.
Inhoudsopgave 1 Informatie en bronnen vinden............................................................................4 2 Voor- en achterkant............................................................................................. 5 3 Snelle installatie.................................................................................................... 7 4 Het verwijderen en installeren van onderdelen..............................................9 De batterij verwijderen................................
Informatie en bronnen vinden 1 Raadpleeg de documentatie over veiligheid en regelgeving die bij uw computer is meegeleverd en de website over wet- en regelgeving op www.dell.com/regulatory_compliance voor meer informatie over: • Beste veiligheidsmaatregelen • Certificering • Ergonomie Zie www.dell.com voor extra informatie over: • Garantie • Algemene voorwaarden (alleen V.S.) • Gebruiksrechtovereenkomst Kijk voor meer informatie over uw product op www.dell.com/support/manuals .
Voor- en achterkant 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 2 Microfoon Statuslampje voor camera Camera Sluiterknop van de camera Sensor voor omgevingslicht Pen Aan-/uitknop Micro seriële poort USB 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
Snelle installatie 3 GEVAAR: Lees de veiligheidsinformatie die bij uw computer wordt geleverd, voordat u de procedures in deze sectie uitvoert. Zie www.dell.com/regulatory_compliance voor meer informatie over beste praktijken GEVAAR: De netadapter is geschikt voor stopcontacten wereldwijd. Stroomaansluitingen en stekkerblokken kunnen echter per land verschillen.
OPMERKING: Het wordt aanbevolen om uw computer ten minste een keer aan en uit te zetten voordat u een kaart gaat installeren of de computer op een dockingstation aansluit of een ander extern apparaat zoals een printer.
Het verwijderen en installeren van onderdelen 4 Deze paragraaf beschrijft gedetailleerd hoe de onderdelen moeten worden verwijderd uit, of worden geïnstalleerd in uw computer. De batterij verwijderen GEVAAR: Wanneer u een batterij gebruikt die niet geschikt is, kunt u het risico op brand of explosie vergroten. Vervang de batterij alleen door een compatibele batterij van Dell die speciaal voor uw computer van Dell ontwikkeld is. Gebruik geen batterij uit een andere tablet.
De batterij plaatsen 1. Schuif de batterij in de houder totdat deze op zijn plaats klikt. 2. Vergrendel de batterij door de vergrendeling van de batterij af te schuiven. De SIM-kaart plaatsen OPMERKING: De sleuf voor de SIM-kaart bevindt zich onder de sleuf van batterij 2. 1. Verwijder de batterij. 2. Doe het volgende om de SIM-kaart te plaatsen: a. Druk op de vergrendeling van de SIM-kaart en trek de kaart naar buiten. b. Steek de SIM-kaart in de sleuf. c.
Dell Rugged Control Center Toepassing 5 De Dell Rugged Control Center (RCC) is een toepassing voor uw Dell Latitude 12 Rugged tablet, waarmee u op de tablet een aantal belangrijke taken kunt uitvoeren. Na dat u de toepassing Dell Rugged Control Center op uw tablet geïnstalleerd heeft, kunt u alle basisfuncties bekijken, zoals Wi-Fi , Bluetooth, camera, volume, helderheid, enz. Daarnaast kunt u met deze toepassing ook hierop ook een snelkoppeling van een functie toevoegen.
Functie Beschrijving Hiermee kunt u de service WWAN in- of uitschakelen (indien geconfigureerd). Hiermee kunt u Bluetooth in- of uitschakelen. Hiermee kunt u de ingebouwde zaklamp in- of uitschakelen. Hiermee kunt u de automatische lichtsensor in- of uitschakelen. Hiermee opent u de toepassing Camera. Hiermee opent u het GPS-configuratiescherm, waarmee u de GPS-functie kunt in- of uitschakelen.
Met de optie Instellingen in Rugged Control Center U kunt ook tikken op de verkennen. optie in de rechterbovenhoek van de toepassing RCC om meer opties te De volgende tabel toont de functiebeschrijving beschikbaar in de optie Instellingen van de toepassing RCC: Functie Beschrijving Hiermee opent u het configuratiescherm van Windows voor instellingen voor pen en aanraken. OPMERKING: Deze optie is alleen compatibel als u voor uw tablet het optionele toetsenbord heeft.
Functie Beschrijving Hiermee opent u een bedieningspaneel om voor de 3 programmeerbare toetsen op de voorzijde van de tablet functies te definiëren. Hiermee opent u het configuratiescherm van Windows voor batterij-instellingen. Hiermee opent u het configuratiescherm in Windows. Hiermee opent u het configuratiescherm om de instellingen van de toepassing RCC aan te passen. De Dell Rugged Control Center installeren OPMERKING: 1. • Dell Rugged Control Center is alleen compatibel met Windows 8 of hoger.
De toetsenbordverlichting aan- of uitzetten OPMERKING: Deze functie kan alleen worden gebruikt als de tablet is aangesloten op een extern toetsenbord (afzonderlijk verkrijgbaar). 1. Start de toepassing Rugged Control Center. 2. Druk op de Instellingen 3. Druk op de knop Toetsenbordverlichting. toetsenbordverlichting te openen. 4. Pas de benodigde parameters voor de instellingen en de kleuren van de verlichting aan. knop in de rechterbovenhoek.
2. 16 Druk op de toetsen + < F10> om de helderheid aan te passen.
6 Stealth-modus De uiterst robuuste Latitude-producten worden geleverd met een Stealth-modus. In deze modus kunt u het beeldscherm, alle LED-lampjes, de ingebouwde luidsprekers, de ventilator en alle draadloze radiosystemen met één toetsencombinatie uitschakelen. OPMERKING: De modus is handig wanneer u geheime taken moet uitvoeren. Wanneer de Stealthmodus is ingeschakeld, blijft de tablet gewoon werken. Licht en geluid zijn echter uitgeschakeld.
3. Stel een van de 3 programmeerbare toetsen in om de Stealth-modus in of uit te schakelen. 4. Gebruik de geselecteerde programmeerbare toetsen om de Stealth-modus in- of uit te schakelen. De instellingen van de Stealth-modus aanpassen In de Stealth-modus kunt u uw favoriete functies ook uitschakelen. Doe het volgende om de instellingen van de Stealth-modus te wijzigen: 1. Start de toepassing Rugged Control Center op uw tablet. 2. Druk op het hoofdscherm op de knop Instellingen 3.
De functie Wi-Fi in- en uitschakelen 7 U kunt de draadloze verbinding (Wi-Fi) in- of uitschakelen met behulp van het optionele toetsenbord en met de programmeerbare toetsen in toepassing RCC. OPMERKING: Wi-Fi kan ook worden in- en uitgeschakeld met behulp van de door de gebruiker gedefinieerde programmeerbare toetsen op de tablet. Het in- of uitschakelen van draadloze functie (Wi-Fi) met het optionele toetsenbord 1. Druk op de toetsen + om de Wi-Fi in te schakelen. 2.
5. 20 Gebruik de geprogrammeerde toets om draadloze netwerken op de tablet in/uit te schakelen.
Smart cards 8 Er zijn twee soorten Smart cards of Common Access Cards (CAC): 1. Ingebouwde Smart cards — Deze kaarten hebben een gedeelte met vergulde contactpunten. Wanneer u deze kaarten in een kaartlezer plaatst, kunt u informatie uitlezen en wegschrijven. Plaats de kaart in de smart card-sleuf. Zorg dat het vergulde gedeelte omhoog en in de richting van de sleuf wijst. Schuif de kaart in de sleuf tot goed zit. 2.
Technische gegevens 9 OPMERKING: Aanbiedingen kunnen per regio verschillen. De volgende specificaties worden in naleving van de wet bij de computer meegeleverd. Ga voor meer informatie over de configuratie van uw computer naar Help en ondersteuning in uw Windows-besturingssysteem en selecteer de optie om informatie over uw computer te bekijken.
Communicatie Netwerkadapter WLAN, LTE, HSPA+ Wireless (Draadloos) BT, NFC • Bluetooth 4.0 LE OPMERKING: De optionele I/O-uitbreidingsmodule, mits gelijktijdig met de tablet aangeschaft, is uitgerust met een extra netwerkaansluiting (Ethernet). Poorten en connectoren Audio één 3,5 mm ingang Video één mini HDMI-aansluiting USB één USB 3.
Beeldscherm Functie Specificatie Minimale kijkhoeken: Horizontaal • • +/- 40° voor HD +/- 60° voor FHD Verticaal • • +10°/-30° voor HD +/- 50° voor FHD Pixel pitch 0,2265 mm Camera voorzijde Type OV 2724 (2 MP) Resolutie 1366 x 768 pixels Camera achterzijde Type IMX 134 (8 MP) Resolutie 3264 x 2448 pixels Opslag Opslag M.
Netadapter ingangsstroom (maximum) 0,60 A Inputfrequentie 50 Hz tot 60 Hz Uitgangsvermogen 45 W Uitgangsstroom (45 W) 2,31 A Nominale uitgangsspanning 19,5 VDC Temperatuurbereik: Operationeel 0 °C tot en met 40 °C (32 °F tot en met 104 °F) Niet in gebruik -40 °C tot en met 70 °C (-40 °F tot en met 158 °F) Fysiek Normaal Breedte 312,20 mm (12,29 inches) Hoogte 203,00 mm (7,99 inches) Dikte 24,40 mm (0,96 inch) Maximaal Breedte 318,20 mm (12,53 inches) Hoogte 209,00 mm (8,23 inches) Di
Contact opnemen met Dell 10 OPMERKING: Als u geen actieve internetverbinding hebt, kunt u de contactgegevens vinden op de factuur, de pakbon of in de productcatalogus van Dell. Dell biedt diverse online en telefonische ondersteunings- en servicemogelijkheden. De beschikbaarheid verschilt per land en product en sommige services zijn mogelijk niet beschikbaar in uw regio. Wanneer u met Dell contact wilt opnemen voor vragen over de verkoop, technische ondersteuning of de klantenservice: Ga naar dell.
Dell Latitude 12 Rugged Tablet – 7202 Handbuch zum Einstieg Vorschriftenmodell: T03H Vorschriftentyp: T03H001
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG liefert wichtige Informationen, mit denen Sie den Computer besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis 1 Informationen und Ressourcen......................................................................... 4 2 Vorder- und Rückansicht.................................................................................... 5 3 Setup-Kurzanleitung............................................................................................ 7 4 Entfernen und Einbauen von Komponenten...................................................9 Entfernen des Akkus...............................................
Informationen und Ressourcen 1 Weitere Informationen zu folgenden Themen finden Sie in den Dokumenten mit Sicherheitshinweisen und Betriebsbestimmungen im Lieferumfang Ihres Computers sowie auf der Homepage zur Einhaltung gesetzlicher Vorschriften unter www.dell.com/regulatory_compliance: • Bestmögliche Einhaltung der Sicherheitsbestimmungen • Kontrollzertifikat • Ergonomie Unter www.dell.
Vorder- und Rückansicht 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 2 Microphone Kamerastatusanzeige Kamera Kameraauslöseschalter Umgebungslichtsensor Stift Netzschalter Serieller Micro-Anschluss USB 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
Setup-Kurzanleitung 3 WARNUNG: Bevor Sie gemäß den in diesem Abschnitt beschriebenen Anleitungen verfahren, lesen Sie zunächst die Sicherheitshinweise in der entsprechenden Dokumentation im Lieferumfang Ihres Computers. Weitere Informationen zu empfohlenen und bewährten Praktiken finden Sie unter www.dell.com/regulatory_compliance WARNUNG: Der Netzadapter funktioniert mit allen Steckdosen weltweit. Die Stecker oder Steckdosenleisten können jedoch unterschiedlich sein.
Abbildung 3. Netzschalter ANMERKUNG: Es wird empfohlen, den Computer mindestens einmal einzuschalten und herunterzufahren, bevor Sie Karten installieren oder den Computer mit einem Docking-Gerät oder einem anderen externen Gerät wie einem Drucker verbinden.
Entfernen und Einbauen von Komponenten 4 Dieser Abschnitt bietet detaillierte Informationen über das Entfernen und Einbauen von Komponenten Ihres Computers. Entfernen des Akkus WARNUNG: Bei Verwendung ungeeigneter Akkus besteht Brand- oder Explosionsgefahr. Ersetzen Sie den Akku nur durch einen kompatiblen Akku von Dell. Der Akku wurde für den Einsatz in Tablets von Dell konzipiert. Setzen Sie keine Akkus von anderen Tablets in Ihr Tablet ein.
Einsetzen des Akkus 1. Schieben Sie den Akku in den Steckplatz, bis er hörbar einrastet. 2. Verriegeln Sie den Akku, indem Sie den Riegel vom Akku wegschieben. Einbauen der SIM-Karte ANMERKUNG: Der SIM-Kartensteckplatz befindet sich unterhalb des Akku 2-Steckplatzes. 1. Entfernen Sie den Akku. 2. So installieren Sie die SIM-Karte: a. Drücken Sie auf die SIM-Kartenverriegelung und ziehen Sie sie nach außen. b. Einsetzen der SIM-Karte in das Fach. c.
11
5 Dell Rugged Control Center-Anwendung Das Dell Rugged Control Center (RCC) ist eine für Ihr Dell Latitude 12 Rugged Tablet entwickelte Anwendung, die Ihnen die Ausführung mehrerer wichtiger Aufgaben auf dem Tablet ermöglicht. Nachdem Sie die Dell Rugged Control Center-Anwendung auf Ihrem Tablet installiert haben, können Sie alle grundlegenden Funktionen, wie Wi-Fi, Bluetooth, Kamera, Lautstärke, Helligkeit usw. anzeigen.
Funktion Beschreibung Ermöglicht die Aktivierung oder Deaktivierung des WWAN/Mobiles Breitband-Dienstes. Ermöglicht die Aktivierung oder Deaktivierung von Bluetooth. Ermöglicht die Aktivierung oder Deaktivierung der integrierten Taschenlampe. Ermöglicht die Aktivierung oder Deaktivierung des Automatic Light Sensor. Starte die Kameraanwendung. Startet die GPS-Systemsteuerung, die Ihnen die Aktivierung oder Deaktivierung des GPS ermöglicht.
Verwenden der Einstellungsoption im Rugged Control Center Sie können auch die Option über die rechte obere Ecke der RCC-Anwendung berühren, um weitere Optionen zu durchsuchen. Die folgende Tabelle zeigt die in der Option Einstellungen der RCC-Anwendung verfügbare Funktionsbeschreibung: Funktion Beschreibung Startet die Windows-Systemsteuerung für die Stiftund Touch-Einstellungen. ANMERKUNG: Diese Option ist nur kompatibel, wenn Sie über die optionale Tastatur für Ihre Tablet verfügen.
Funktion Beschreibung Startet eine Systemsteuerung zum Anpassen des Stealth-Modus. Die Systemsteuerung ermöglicht es Ihnen außerdem, festzulegen, welche Funktionalität deaktiviert ist, wenn Sie den StealthModus starten. Startet eine Systemsteuerung zum Zuweisen von Aktionen zu den 3 programmierbaren Schaltflächen auf der Vorderseite des Tablets. Startet die Windows-Systemsteuerung für Akkueinstellungen. Startet die Windows-Systemsteuerung.
5. Klicken Sie auf Yes (Ja), um die Administratorrechte zum Starten des Installationsvorgangs zu erteilen. Der Installationsvorgang wird jetzt gestartet. 6. Wenn die Installation erfolgreich ist, klicken Sie auf Fertigstellen. Sie können nun das Rugged Control Center-Symbol auf Ihrem Desktop sehen. Aktivieren oder Deaktivieren der Tastaturhintergrundbeleuchtung ANMERKUNG: Diese Funktion kann nur verwendet werden, wenn das Tablet an eine externe Tastatur angeschlossen ist (separat erhältlich). 1.
2. Drücken Sie die Tastenkombination + < F10>, um die Helligkeit anzupassen.
Stealth-Modus 6 Die robusten Latitude-Produkte sind mit dem Stealth-Modus ausgestattet. Mit dem Stealth-Modus können Sie den Bildschirm, alle LED-Anzeigen, interne Lautsprecher, den Lüfter und alle Wireless-Sender mit einer einzigen Tastenkombination ausschalten. ANMERKUNG: Diese Betriebsart eignet sich für die Verwendung des Tablets in verborgenen Abläufen. Wenn der Stealth-Modus aktiviert ist, arbeitet das Tablet weiter, gibt jedoch kein Licht und keinen Ton von sich.
Aktivieren/Deaktivieren des Stealth-Modus mithilfe von RCC 1. Starten Sie die Rugged Control Center-Anwendung auf Ihrem Tablet. 2. Drücken Sie auf dem Hauptbildschirm die Schaltfläche Settings (Einstellungen) Buttons (Programmierbare Schaltflächen). 3. Legen Sie 3 beliebige programmierbare Schaltflächen fest, um den Stealth-Modus zu aktivieren oder zu deaktivieren. 4. Verwenden Sie die ausgewählten programmierbaren Schaltflächen, um den Stealth-Modus zu aktivieren oder zu deaktivieren.
7 Aktivieren und Deaktivieren der WirelessFunktion (Wi-Fi) Sie können die Wireless (Wi-Fi)-Funktion mithilfe der optionalen Tastatur und der programmierbaren Schaltflächen in der RCC-Anwendung aktivieren oder deaktivieren. ANMERKUNG: WiFi kann auch über die programmierbaren Schaltflächen auf dem Tablet aktiviert/ deaktiviert werden. Aktivieren oder Deaktivieren der Wireless (WI-Fi)Funktion mithilfe der optionalen Tastatur 1.
5. Verwenden Sie die programmierten Schaltflächen, um Wireless-Netzwerke auf dem Tablet zu aktivieren oder zu deaktivieren.
Smart Cards 8 Es gibt zwei Haupttypen von Smart – oder Common Access Cards (CACs): 1. Eingeschlossene Smart Cards – Diese Karten haben einen Kontaktbereich mit zahlreichen vergoldeten Anschlusskonsolen. Wenn Sie den Chip in ein Kartenlesegerät einfügen, können die auf ihm vorhandenen Informationen gelesen und geschrieben werden. Setzen Sie die Karte in den Steckplatz für die Smartcard ein, wobei die goldene Kontaktfläche nach oben und zum Steckplatz der Smartcard zeigt.
Technische Daten 9 ANMERKUNG: Die angebotenen Konfigurationen können je nach Region variieren. Die folgenden Angaben enthalten nur die technischen Daten, die laut Gesetz im Lieferumfang Ihres Computers enthalten sein müssen. Weitere Informationen über die Konfiguration Ihres Computers finden Sie im Abschnitt Help and Support (Hilfe und Support) des Windows-Betriebssystems. Wählen Sie die Option zur Anzeige von Informationen über Ihren Computer aus.
Kommunikation Netzwerkadapter WLAN, LTE, HSPA+ Wireless BT, NFC • Bluetooth 4.0 LE ANMERKUNG: Das optionale E/A-Erweiterungsmodul ist, wenn mit dem Tablet gekauft, mit einem zusätzlichen Netzwerkanschluss (Ethernet) ausgestattet. Anschlüsse und Stecker Audio Eine 3,5-mm-Buchse Video 1 Mini-HDMI-Anschluss USB Ein USB 3.
Anzeige Funktion Technische Daten Mindestbetrachtungswinkel: Horizontal • • +/-40° für HD +/-60° für FHD Vertikal • • +10°/-30° für HD +/-50° für FHD Bildpunktgröße 0,2265 mm Kamera an der Vorderseite Typ OV 2724 (2 MP) Lösung 1366 x 768 Pixel Kamera an der Rückseite Typ IMX 134 (8 MP) Lösung 3264 x 2448 Pixel Bei Lagerung Bei Lagerung M.
Netzadapter Eingangsstrom (maximal) 0,6 A Eingangsfrequenz 50 bis 60 Hz Ausgangsleistung 45 W Ausgangsstrom (45 W) 2,31 A Ausgangsnennspannung 19,5 V Gleichspannung Temperaturbereich: Betrieb 0 °C bis 40 °C (32 °F bis 104 °F) Nicht in Betrieb -40 °C bis 70 °C (-40 °F bis 158 °F) Abmessungen und Gewicht Standard Breite 312,20 mm (12,29 Zoll) Höhe 203,00 mm (7,99 Zoll) Dicke 24,40 mm (0,96 Zoll) Maximal Breite 318,20 mm (12,53 Zoll) Höhe 209,00 mm (8,23 Zoll) Dicke 28,90 mm (1,14 Zoll
Kontaktaufnahme mit Dell 10 ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit. Da die Verfügbarkeit dieser Optionen je nach Land und Produkt variiert, stehen einige Services in Ihrer Region möglicherweise nicht zur Verfügung.
Tablet Dell Latitude 12 Rugged Tablet – 7202 Guida introduttiva Modello normativo: T03H Tipo normativo: T03H001
Messaggi di N.B., Attenzione e Avvertenza N.B.: Un messaggio di N.B. indica informazioni importanti che contribuiscono a migliorare l'utilizzo del computer. ATTENZIONE: Un messaggio di ATTENZIONE indica un danno potenziale all'hardware o la perdita di dati, e spiega come evitare il problema. AVVERTENZA: Un messaggio di AVVERTENZA indica un rischio di danni materiali, lesioni personali o morte. Copyright © 2015 Dell Inc. Tutti i diritti riservati.
Sommario 1 Individuare informazioni e risorse..................................................................... 4 2 Vista anteriore e posteriore.................................................................................5 3 Installazione rapida...............................................................................................7 4 Rimozione e installazione dei componenti..................................................... 9 Rimozione della batteria.........................................
Individuare informazioni e risorse 1 Consultare i documenti sulla sicurezza e normativi spediti con il computer e il sito Web sulla conformità normativa all'indirizzo www.dell.com/regulatory_compliance per maggiori informazioni su: • Best practice sulla sicurezza • Certificazione normativa • Ergonomia Consultare www.dell.
Vista anteriore e posteriore 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 2 Microfono Indicatore di stato della fotocamera Webcam Interruttore dell'otturatore della fotocamera Sensore di luminosità ambientale Stilo Accensione Porta micro a seriale connettore USB 3.
13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
Installazione rapida 3 AVVERTENZA: Prima di iniziare le procedure descritte in questa sezione, leggere le informazioni sulla sicurezza fornite assieme al computer. Per maggiori informazioni sulle best practice, consultare il sito Web www.dell.com/regulatory_compliance AVVERTENZA: L'adattatore c.a. è compatibile con le prese elettriche di tutto il mondo. I connettori di alimentazione e le prese multiple variano in base al paese.
N.B.: È consigliabile accendere il computer ed arrestare il sistema almeno una volta prima di installare eventuali schede o collegare il computer ad una periferica di alloggiamento, oppure ad un'altra periferica esterna, quale una stampante.
4 Rimozione e installazione dei componenti La seguente sezione fornisce informazioni dettagliate su come rimuovere o installare i componenti dal computer. Rimozione della batteria AVVERTENZA: L'utilizzo di batterie non compatibili potrebbe aumentare il rischio di incendi o esplosioni. Sostituire la batteria solo con una batteria compatibile acquistata da Dell. La batteria è progettata per funzionare con il tablet Dell. Non utilizzare una batteria proveniente da altri tablet.
Installazione della batteria 1. Far scorrere la batteria nel relativo slot finché non scatta in posizione. 2. Bloccare la batteria facendo scorrere il dispositivo di chiusura a scatto. Installazione della scheda SIM N.B.: Lo slot della scheda SIM si trova sotto lo slot della batteria 2. 1. Rimuovere la batteria. 2. Per installare la scheda SIM: a. Premere il fermo della SIM e tirarlo verso l'esterno. b. Inserire la scheda SIM nell'alloggiamento. c. Spingere il fermo della SIM per bloccarlo. 3.
5 Applicazione Dell Rugged Control Center Rugged Control Center (RCC) di Dell è un'applicazione progettata per il tablet Latitude 12 Rugged di Dell, che consente di eseguire sul tablet diverse attività importanti. Dopo aver installato l'applicazione Rugged Control Center sul tablet, è possibile visualizzare tutte le principali funzioni, tra cui connessione Wi-Fi, Bluetooth, fotocamera, volume, luminosità e molto altro.
Funzione Descrizione Consente di attivare o disattivare il servizio a banda larga WWAN/Mobile (se configurato) Consente di attivare o disattivare la connessione Bluetooth. Consente di accendere e spegnere il flash incorporato. Consente di attivare o disattivare il Sensore di luce automatico. Consente di avviare l'applicazione della fotocamera. Consente di avviare il pannello di controllo GPS con il quale è possibile attivare o disattivare il GPS.
Utilizzando l'opzione Impostazioni in Rugged Control Center È anche possibile toccare altre opzioni. un'opzione dall'angolo in alto a destra dell'applicazione RCC per esplorare La tabella di seguito contiene una descrizione delle funzioni disponibili nell'opzione Impostazioni per l'applicazione RCC: Funzione Descrizione Consente di avviare il pannello di controllo di Windows per le impostazioni penna e tocco. N.B.: Questa opzione è compatibile solo se si possiede la tastiera opzionale per il tablet.
Funzione Descrizione Consente di avviare un pannello di controllo per assegnare azioni ai 3 pulsanti programmabili sulla parte anteriore del tablet. Consente di avviare il pannello di controllo di Windows per le impostazioni della batteria. Consente di avviare il pannello di controllo di Windows. Consente di avviare il pannello di controllo per regolare le impostazioni dell'applicazione RCC: Installazione di Rugged Control Center N.B.: 1.
Attivazione/Disattivazione della retroilluminazione della tastiera N.B.: Questa funzione può essere utilizzata solo se il tablet è collegato una tastiera esterna (in vendita separatamente). 1. Avviare l'applicazione Rugged Control Center. 2. Premere Impostazioni 3. Premere il pulsante Tastiera retroilluminata Tastiera retroilluminata. 4. Regolare i parametri richiesti per le impostazioni di retroilluminazione e i colori di retroilluminazione. nell'angolo in alto a destra.
2. 16 Premere i tasti + < F10> per regolare la luminosità.
Modalità invisibile 6 I prodotti Latitude Rugged vengono forniti dotati della modalità invisibile. La modalità invisibile consente di spegnere il display, tutti gli indicatori LED, gli altoparlanti interni, la ventola e le radio wireless con una singola combinazione di tasti. N.B.: Questa modalità ha lo scopo di utilizzare il computer in operazioni segrete. Quando è attivata la modalità invisibile, il computer rimane funzionale ma non emette alcuna luce o alcun suono.
Attivare/Disattivare la modalità invisibile utilizzando RCC 1. Avviare l'applicazione Rugged Control Center sul tablet. 2. Dalla schermata iniziale, premere il pulsante Impostazioni 3. Impostare uno dei 3 pulsanti programmabili per attivare o disattivare la modalità invisibile. 4. Utilizzare il pulsante programmabile per attivare o disattivare la modalità invisibile. > Pulsanti programmabili.
Attivazione e disattivazione della funzione senza fili (WiFi) 7 È possibile attivare o disattivare la funzione senza fili (Wi-Fi), utilizzando la tastiera opzionale e mediante i pulsanti programmabili nell'applicazione RCC. N.B.: La funzione WiFi può anche essere attivata/disattivata utilizzando i tasti programmabili dall'utente presenti sul tablet. Attivazione o disattivazione della funzione senza fili (WiFi) utilizzando la tastiera opzionale 1.
5. 20 Utilizzare il pulsante programmato per Attivare/Disattivare le reti senza fili sul tablet.
Schede smart 8 Ci sono due tipi di schede Smart o Common Access Cards (CAC): 1. Schede Smart incorporate: queste schede possiedono un'area di contatto con strisce di contatto dorate. Quando le si inserisce in un lettore di schede, le informazioni da un chip possono essere lette e scritte. Inserire la scheda nello slot per scheda Smart con la striscia di contatto dorata rivolta verso l'alto e verso lo slot per smart card.
9 Specifiche N.B.: Le offerte possono variare in base alla regione. Le seguenti specifiche sono esclusivamente quelle richieste dalla legge per la spedizione del computer. Per maggiori informazioni sulla configurazione del computer, fare clic su Guida e supporto e selezionare l'opzione per visualizzare le informazioni sul computer.
Comunicazioni Adattatore di rete WLAN, LTE, HSPA+ Wireless BT, NFC • Bluetooth 4.0 a basso consumo energetico N.B.: Il modulo di espansione I/O opzionale, se acquistato con il tablet, è dotato di una porta di rete aggiuntiva (Ethernet). Porte e connettori Audio un jack da 3,5 mm Video connettore singolo per mini HDMI USB un connettore USB 3.
Schermo Caratteristica Specifiche Frequenza d'aggiornamento 60 Hz Angolo di visualizzazione minimo: Orizzontale • • +/- 40° per HD +/- 60° per FHD Verticale • • +10°/-30° per HD +/- 50° per FHD Passo pixel 0,2265 mm fotocamera anteriore Tipo OV 2724 (2 MP) Risoluzione 1366 x 768 pixel Fotocamera posteriore Tipo IMX 134 (8 MP) Risoluzione 3264 x 2448 pixel Storage Storage SSD M.
Adattatore c.a. Tipo Tensione d'ingresso da 100 V c.a. a 240 V c.a. Corrente d'ingresso (massima) 0,60 A Frequenza d'entrata da 50 Hz a 60 Hz Alimentazione di uscita 45 W Corrente di uscita (45 W) 2,31 A Tensione nominale di uscita 19,5 V c.c.
26
Come contattare Dell 10 N.B.: Se non si dispone di una connessione Internet attiva, è possibile trovare i recapiti sulla fattura di acquisto, sulla distinta di imballaggio, sulla fattura o sul catalogo dei prodotti Dell. Dell offre diverse opzioni di servizio e assistenza telefonica e online. La disponibilità varia per paese e prodotto, e alcuni servizi potrebbero non essere disponibili nella vostra zona.