Dell Latitude 7210 2-i-1 Servicehandbok Regleringsmodell: T04J Regleringstyp: T04J002
Anmärkningar, försiktighetsbeaktanden och varningar OBS: OBS innehåller viktig information som hjälper dig att få ut det mesta av produkten. CAUTION: VIKTIGT anger antingen risk för skada på maskinvara eller förlust av data och förklarar hur du kan undvika problemet. VARNING: En VARNING visar på en potentiell risk för egendoms-, personskador eller dödsfall. © 2020 Dell Inc. eller dess dotterbolag. Med ensamrätt. Dell, EMC och andra varumärken är varumärken som tillhör Dell Inc. eller dess dotterbolag.
Innehåll 1 Arbeta med datorn........................................................................................................................5 Säkerhetsanvisningar............................................................................................................................................................ 5 Stänga av datorn – Windows 10..........................................................................................................................................
Alternativ på systemloggskärmen................................................................................................................................82 Systemlogg...........................................................................................................................................................................82 Uppdatera BIOS .......................................................................................................................................................
1 Arbeta med datorn Säkerhetsanvisningar Förutsättningar Följ dessa säkerhetsföreskrifter för att skydda datorn och dig själv. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: • • Du har läst säkerhetsinformationen som medföljde datorn. En komponent kan ersättas eller – om du köper den diskret – monteras i omvänd ordning jämfört med borttagningsproceduren. Om denna uppgift OBS: Koppla bort alla strömkällor innan du öppnar datorkåpan eller panelerna.
OBS: Kontrollera att datorn och alla anslutna enheter är avstängda. Om datorn eller någon ansluten enhet inte stängdes av automatiskt när du stängde av operativsystemet trycker du ned strömknappen i 6 sekunder för att stänga av dem. Innan du arbetar inuti datorn Om denna uppgift För att undvika att skada datorn ska du utföra följande åtgärder innan du börjar arbeta i den. Steg 1. Se till att följa säkerhetsföreskrifterna. 2. Se till att arbetsytan är ren och plan så att inte datorkåpan skadas. 3.
2 Isärtagning och ihopsättning Isärtagning och ihopsättning Säkerhetsanvisningar Förutsättningar Följ dessa säkerhetsföreskrifter för att skydda datorn och dig själv. Om inget annat anges förutsätts i varje procedur i det här dokumentet att följande villkor har uppfyllts: • • Du har läst säkerhetsinformationen som medföljde datorn. En komponent kan ersättas eller – om du köper den diskret – monteras i omvänd ordning jämfört med borttagningsproceduren.
Om denna uppgift OBS: Innan du utför något arbete inuti surfplattan ska du läsa säkerhetsinstruktionerna som medföljde plattan. Mer information om bästa praxis gällande säkerhet finns på sidan Regulatory Compliance på www.dell.com/ regulatory_compliance CAUTION: Många reparationer ska endast utföras av certifierade servicetekniker.
Förbindelse Förbindelse är en metod för att ansluta två eller flera jordledare till samma elektriska potential. Detta görs genom användning av ett ESDkit (Field Service Electrostatic discharge). Vid anslutning av en bindningstråd, se alltid till att den är ansluten till bar metall och aldrig till en målade eller icke-metallyta. Handledsremmen ska vara säker och i full kontakt med din hud, och se till att alltid ta bort alla smycken som klockor, armband eller ringar innan du själv och utrustningen förbinds.
• • • • handledsremmens jordningstråd på testverktyget medan det är fastspänt på handleden och trycker på knappen för att testa. En grön LED lyser om testet lyckades, en röd LED tänds och ett larm ljuder om testet misslyckas. Isolatorelement - Det är viktigt att hålla ESD-känsliga enheter, såsom kylflänsens platshöljen, borta från inre delar som är isolatorer och ofta är laddade. Arbetsmiljö - Innan du använder ESD-fältservicekittet ska du utvärdera situationen på kundanläggningen.
Figur 1. Stänga av batteriströmmen Ta bort SD-minneskortet Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Lägg surfplattan på en plan och platt yta, med det utfällbara stödet vänt uppåt. 3. Tryck på SD-kortet för att mata ut det från kortplatsen 4. Ta bort SD-kortet från surfplattan. Ta bort SIM-kortshållaren Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Sätt i ett stift i frigöringshålet för att frigöra SIM-kortshållaren. 3.
2. Ta bort: a) SD-kort b) SIM 3. Ta bort de sex skruvarna (icke-säkerhetskonfiguration)/sex fästskruvarna (säkerhetskonfiguration) som håller fast Latitude 7210 2-i-1 bildskärm i systemets chassi. 4. Använd en plastrits och tryck på de två spärrhålen bredvid gångjärnen för att lossa bildskärmen från bildskärmens bakre kåpa.
5. Vänd på systemet så att bildskärmen är vänd uppåt. 6. Sätt i plastritsen i den lucka som skapades i steg #1 och använd en sugkopp (valfritt) för att bända upp bildskärmen från det nedre vänstra hörnet på systemets framsida. Arbeta runt till bildskärmens högra sida.
7. Arbeta runt till bildskärmens vänstra sida. 8. Vänd försiktigt på bildskärmen från den övre kanten och lägg den med bildskärmen nedåt bredvid bildskärmens bakre kåpa. Dra inte bort bildskärmen från basen. Bildskärmen är fortfarande ansluten till moderkortet på basen via bildskärmskabeln. Vänd försiktigt på bildskärmen och koppla bort bildskärmskabeln.
9. Skjut batteriets strömbrytare på moderkortet till OFF. 10. Ta bort de två skruvarna M2x2,5 [1] som håller fast bildskärmens kabelfäste [2] på moderkortet och ta bort bildskärmens kabelfäste.
11. Koppla bort bildskärmskabeln [3] från moderkortet och ta bort bildskärmspanelen från systemet.
Installera bildskärmspanelen Steg 1. Anslut bildskärmskabeln till kontakten på moderkortet [1]. 2. Sätt tillbaka de två skruvarna M2x2,5 [3] som håller fast bildskärmens kabelfäste på moderkortet och ta sätt tillbaka bildskärmens kabelfäste [2].
3. Skjut batteriets strömbrytare på moderkortet till ON. Anslut försiktigt bildskärmen till moderkortet med bildskärmskabeln och vänd på bildskärmen så att den är vänd uppåt. 4.
5. Sätt tillbaka de sex skruvarna (icke-säkerhetskonfiguration)/sex fästskruvarna (säkerhetskonfiguration) som håller fast Latitude 7210 2-i-1 bildskärm i systemets chassi. 6. Stäng det utfällbara stödet.
7. Installera: a) SD-kort b) SIM 8. Följ anvisningarna i när du har arbetat inuti surfplattan.
SSD-disk Ta bort SSD-disken Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Så här tar du bort SSD-enhetshållaren: OBS: SIM-kortplats är endast tillgänglig på surfplattor med WWAN-modulen. a) Ta bort skruven M2x2,5 som fäster fästet på SSD-disken [1]. b) Ta bort fästet från SSD-disken [2]. 4.
Skjut ut och lyft av SSD-disken från moderkortet. Installera SSD-disken Steg 1.
2. Placera fästet på SSD-disken [1]. OBS: Justera skärmen försiktigt för att undvika skador på klipphuvudena.
3. Sätt tillbaka skruvarna M2x2,5 som håller fast fästet i SSD-disken 4. Installera: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 5. Följ anvisningarna i Innan du arbetar inuti surfplattan. WLAN-kort Ta bort WLAN-kortet Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Ta bort skruvarna M2x2,5 som håller fast WLAN-fästet i WLAN-kortet [1]. 4. Ta bort WLAN-fästet [2]. 5. Koppla bort antennkablarna från WLAN-kortet [3].
6. Skjut ut och ta bort WLAN-kortet från WLAN-kortplatsen [4]. Installera WLAN-kortet Steg 1. Rikta in spåret på WLAN-kortet med fliken på WLAN-kortplatsen och sätt in WLAN-kortet i en vinkel i WLAN-kortplatsen [1]. 2. Anslut antennkablarna till WLAN-kortet. [2] 3.
4. M2x3,0 som håller fast WLAN-fästet i WLAN-kortet. 5. Installera: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan.
WWAN-kort Ta bort WWAN-kortet Om denna uppgift Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Ta bort skruvarna M2x2,5 som håller fast WWAN-fästet i WWAN-kortet [1]. 4. Ta bort WWAN-fästet [2]. 5. Koppla bort antennkablarna från WWAN-kortet [3]. 6. Skjut ut och ta bort WLAN-kortet från WWAN-kortplatsen [4].
Installera WWAN-kortet Om denna uppgift Steg 1. Rikta in spåret på WWAN-kortet med fliken på WWAN-kortplatsen och sätt in WWAN-kortet i en vinkel i WWAN-kortplatsen [1]. 2. Anslut antennkablarna till WWAN-kortet. [2] 3. Placera WWAN-fästet på WWAN-kortet [3] 4. M2x3,0 som håller fast WWAN-fästet i WWAN-kortet. 5. Installera: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan.
• Ladda ur batteriet så mycket som möjligt innan du tar bort det från datorn. Detta kan göras genom att koppla bort nätadaptern från systemet för att låta batteriet laddas ur. • Undvik att krossa, tappa, skada eller tränga in i batteriet med främmande föremål. • Utsätt inte batteriet för höga temperaturer eller montera isär batteripaketen och -cellerna. • Tryck inte på batteriets yta. • Böj inte batteriet. • Använd inte verktyg av något slag för att bända på eller mot batteriet.
c) Ta bort skruvarna M2x4 som håller fast batteriet i chassit [1]. d) Lyft bort batteriet från chassit [2]. Installera batteriet Steg 1. Rikta in skruvhålen på batteriet med skruvhålen på chassit [1] 2.
3.
4. Sätt fast tejpen på batterikontakten [2]. 5. Installera: a) SD-kort b) SIM 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Kylfläns Ta bort kylflänsenheten Steg 1. Följ anvisningarna i Innan du arbetar inuti din surfplatta. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Ta bort kylflänsskyddet så här a) Lyft upp det vänstra kylflänsskyddet [1] och det högra kylflänsskyddet [2] från kylflänsen. b) Dra bort WLAN-kortkablarna från kabelstyrningarna [2].
c) Lossa i rätt ordning (anges på kylflänsen) fästskruvarna som håller fast kylflänsen i moderkortet 4. Ta bort kylflänsenheten: a) Lossa M2 x 2,5-fästskruvarna (4) som håller fast kylflänsenheten i plattan [1]. OBS: Ta bort skruvarna i samma ordning som bildtextnumren [1, 2, 3, 4] som anges tryckt på kylflänsen. b) Lyft bort kylflänsenheten från plattan [2].
Installera kylflänsen Steg 1.
b) Passa in skruvhålen på kylflänsen med skruvhålen på moderkortet c) Dra i rätt ordning åt fästskruvarna (anges på kylflänsen) som håller fast kylflänsen i moderkortet [2] Isärtagning och ihopsättning 35
d) e) f) g) 36 Passa in skruvhålen på kylflänsfläkten med skruvhålen på moderkortet Sätt tillbaka fästskruvarna M2x2,5 som håller fast kylflänsfläkten på moderkortet [3] För in kylflänsens fläktkabel i kontakten på moderkortet och stäng spärren så att kabeln sitter fast [2] Dra WLAN-antennkablarna genom kabelhållarna på moderkortet [3] Isärtagning och ihopsättning
h) Placera avskärmningen på kylflänsen 2. Installera: a) b) c) d) bildskärmspanelen SD-kort SIM batteri Högtalare Ta bort högtalarna Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Så tar du bort högtalarna: a) Koppla loss högtalarkabeln från kontakten på moderkortet [1].
b) Dra bort tejpbitarna som håller fast högtalarkabeln i chassit [2] c) Ta bort högtalarkabeln från kabelhållarna på chassit.
d) Lyft högtalarna från chassit Installera högtalarna Steg 1.
2. Dra högtalarkablarna genom kabelhållarna på handledsstödet 3.
4. Anslut högtalarkabeln till kontakten på moderkortet 5. Installera: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Framåtvänd kamera Ta bort den framåtvända kameran Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Ta bort den främre kameran så här: a) Använd en plastrits, var försiktig upp och ta av det vänstra skärmskyddet från kanten markerad med en pil.
d) Ta bort M1.6 x 3 skruvarna som håller den främre kameramodulen till systemets chassi. e) Dra av och lyft den främre kameramodulen från surfplattan. Installera den framåtvända kameran Steg 1. Sätt i kameramodulen i spåret på surfplattan. 2. Byt ut M1.6 x 3 skruvarna för att fästa den främre kameramodulen.
3. Anslut den främre kamerakabeln till moderkortet. 4. Placera avskärmningsskyddet för att fästa den främre kameramodulen. OBS: Hantera täckskyddet med försiktighet annars kan det gå sönder. 5. Installera: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Bakåtvänd kamera Ta bort den bakre kameran Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3.
b) Ta bort skruven M1,6x3 (1) som säkrar den bakre kameramodulen [2] c) Ta bort M1.6 x 3 skruven som säkrar den bakre kameramodulen. d) Lyft kameramodulen från surfplattan [3].
Installera bakre kamera Steg 1. För att installera den bakre kameran: a) Sätt i den bakre kameramodulen i urtaget på surfplattan b) Sätt tillbaka skruvarna M1,6x3 för att fästa den bakre kameramodulen c) Anslut den bakre kamerakabeln till moderkortet.
Isärtagning och ihopsättning
2. Installera: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 3. Följ anvisningarna i Innan du arbetar inuti surfplattan. Smartkortlåda Ta bort smart card-hållaren Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) e) f) g) h) i) j) SD-kort SIM batteri M.2 2230 SSD WWAN-kort Bakåtvänd kamera Kylflänsmontering Huvudmodul för WWAN-antenn Moderkort bildskärmspanelen 3.
Isärtagning och ihopsättning
Installera smart card-hållaren Steg 1. Sätt in smart-hållaren i spåret på surfplattan. 2. Byt ut M2x2,5-skruvarna [2] för att fästa smart card-hållaren på surfplattan [1]. 3. Anslut smartkabeln till smart card-modulen.
4. Sätt tillbaka: a) b) c) d) e) f) g) h) Moderkort Huvudmodul för WWAN-antenn Kylflänsmontering Bakåtvänd kamera bildskärmspanelen SD-kort SIM batteri 5. Följ anvisningarna i Innan du arbetar inuti surfplattan. Dockningskortskontakt Ta bort dockningsstationskontakten Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3.
b) Ta bort skruvarna M2x2,5 som fäster dockningsplattans fäste på dockningskortet. c) Ta bort dockningskontakten tillsammans med dess FPC från systemet.
Installera dockningskortet Steg 1. Sätt i dockningsplattan och dockningsfäste i spåret på surfplattan.
2. Sätt tillbaka M2 x 2 skruvarna för att fästa dockningsplattan på surfplattan. 3.
4. Anslut dockningskortskabeln till kontakten på moderkortet. 5. Sätt tillbaka: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Strömbrytarkort Ta bort strömbrytar-dotterkortet Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Lossa alla trådlösa antenner som täcker strömknappens dotterkort FPC.
Figur 2. Ta bort trådlösa antenner 4. Koppla från och dra tillbaka strömknappens dotterkort FPC från moderkortet. 5. Koppla ur och ta bort fingeravtrycksläsaren FFC från strömbrytarens dotterkort. 6. Ta bort de två skruvarna M2x3 som håller strömknappens dotterkort på plats.
Figur 3. Ta bort FFC 7. Använd en plastrits genom att bända på strömknappssensorn vid den övre kanten av strömbrytarens dotterkort ur dess fack. 8. Ta bort strömbrytarens dotterkort tillsammans med dess FPC från bildskärmens baksida. 9. Koppla från strömbrytarens dotterkort FPC från strömbrytarens dotterbräda.
Figur 4. Koppla bort och ta bort strömbrytarkortet Installera strömbrytarkortet Steg 1. Sätt fast dotterkortet tillsammans med dess FPC från bildskärmens baksida.
Figur 5. Fäst dotterkortet med FPC 2. Fäst de två M2 X 2.5 skruvarna som håller strömknappens dotterkort på plats. 3. Installera fingeravtrycksläsaren FFC från strömbrytarens dotterkort.
Figur 6. Installera FPC 4. Sätt dit alla trådlösa antenner som täcker strömknappens dotterkort FPC.
Figur 7. Sätt dit den trådlösa antennen 5. Sätt tillbaka: a) b) c) d) e) Kylflänsmontering bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Moderkort Ta bort moderkortet Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) e) f) g) h) i) SD-kort SIM batteri bildskärmspanelen M.2 2230 SSD WWAN-kort Bakåtvänd kamera Kylflänsmontering Huvudmodul för WWAN-antenn 3.
a) Skjut frigöringshaken på SIM-korthållaren inåt för att släppa dummy SIM-korthållaren. b) Ta bort dummy SIM-korthållare. c) Koppla från strömknappens dotterkort FPC, USB-dotterkort FPC, USH FFC (som levereras med en USH-modul), dockningsanslutning FPC och en högtalarkabel. 4. Dra bort antennkablarna från kabelhållarna.
5. Ta bort moderkortet genom att a) Ta bort de två fästskruvarna M2x3 som håller fast USB Type C-fästet.
b) Ta bort typ-C USB fästet. c) Ta bort den enda skruven M2x3 som håller ljuduttaget på plats.
e) Lyft upp moderkortet från surfplattan [2]. Installera moderkortet Steg 1. Rikta in moderkortet med skruvhållarna i surfplattan. 2. Dra åt de sju skruvarna M2x2 för att fästa moderkortet på surfplattan. OBS: Kom ihåg att justera typ-C-porten och dra åt de två skruvarna för att fästa porten på systemets chassi.
3. Dra åt den enda skruven M2x3 som håller ljuduttaget på plats och placera USB Type C-fästet. 4. Dra åt de två fästskruvarna M2x3 som håller fast USB Type C-fästet.
5.
b) c) d) e) f) g) Kylflänsmontering Bakåtvänd kamera bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. WWAN-antenn Ta bort WWAN-antennmodulen Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Ta bort antennmodulen så här: a) b) c) d) Ta bort WWAN huvudantenn från moderkortet.
Isärtagning och ihopsättning
Installera WWAN-antennmodulen Steg 1. Sätt i antennmodulen i spåret på baksidan av surfplattan. 2. Vänd över antennmodulen WWAN för att fästa den på moderkortet.
3. Dra åt klämmorna på vänster och höger sida av WWAN antennmodul som säkrar den till systemet. 4. Sätt dit WWAN huvudantenn på moderkortet. 5. Sätt tillbaka: a) b) c) d) bildskärmspanelen SD-kort SIM batteri 6. Följ anvisningarna i Innan du arbetar inuti surfplattan. Mikrofon Ta bort mikrofonen Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) SD-kort b) SIM c) bildskärmspanelen 3. Ta bort SD-minneskortet och bildskärmspanelen. 4.
Installera mikrofonen Steg 1. Sätt tillbaka mikrofonens modul-B 2. Skjut ut och sätt tillbaka mikrofonmodulen i facket 3. Anslut mikrofonkabeln till modul-B 4. Installera: a) bildskärmspanelen b) SD-kort c) SIM Bildskärmskabel Ta bort bildskärmskabeln Steg 1. Följ anvisningarna i Innan du arbetar inuti surfplattan. 2. Ta bort: a) b) c) d) SD-kort SIM bildskärmspanelen batteri 3. Dra bort tejpen som täcker (1) bildskärmskontakten och (2) pekskärmsmodulens kontakt. 4.
3 Systeminstallationsprogram Systemkonfigurationen gör det möjligt att hantera maskinvaran för din surfplattastationära datorbärbara dator och ange BIOS-alternativ.
Alternativ Beskrivning Battery Information Visar batteristatus och typ av nätadapter som är ansluten till datorn. Startsekvens Startsekvens Här kan du ändra ordningen som datorn använder när den försöker hitta ett operativsystem. Alternativen är: • Windows Boot Manager Alla alternativ är som standard markerade. Boot List Options Här kan du ändra alternativet för startlistan: • UEFI (Alternativet är aktiverat som standard) Advanced Boot Options Gör att du kan du läsa in äldre ROM.
Alternativ Beskrivning Keyboard Illumination I det här fältet kan du välja operativsystemsläge för tangentbordets belysningsfunktion. Ljusstyrkan för tangentbordet kan ställas in på mellan 0 % och 100 %. Alternativen är: • • Ljus (standard) Dimning (50 %) Keyboard Keyboard Backlight Timeout (tidsgräns för tangentbordets bakgrundsbelysning) tonar ned belysningen med Backlight Timeout batteridriftsalternativet. Den huvudsakliga funktionen för tangentbordsbelysning påverkas inte.
Alternativ Beskrivning SMART Reporting Det här fältet styr huruvida fel på inbyggda hårddiskar ska rapporteras när systemet startar. Den här tekniken är en del av SMART-specifikationen (Self-Monitoring Analysis and Reporting Technology). Det här alternativet är inaktiverat som standard. • Enable SMART Reporting (aktivera SMART-rapportering) USB Configuration Det här är en tillvalsfunktion. Med hjälp av det här fältet konfigurerar du den inbyggda USB-styrenheten.
Alternativ Beskrivning • • • • • • Keyboard Backlight Timeout on Battery Låter dig definiera Tidsgränsen för bakgrundsbelysning för utdimning med batterialternativet. Den huvudsakliga funktionen för tangentbordsbelysning påverkas inte. Tangentbordsbelysningen har fortsatt stöd för de olika belysningsnivåerna. Detta fält har en effekt när bakgrundsbelysningen är aktiverad.
Alternativ Beskrivning Password Configuration Här kan du ange min- och maxlängd för administratörs- och systemlösenorden. Password Bypass Här kan du aktivera eller inaktivera tillståndet att förbigå systemlösenordet och lösenordet för den interna hårddisken när de är inställda. Alternativen är: • • Password Change Disabled (inaktiverat). Det här alternativet är valt som standard.
Alternativ Beskrivning Enable Admin Setup Lockout (aktivera utelåsning från administratörs-BIOS) Det här alternativet är inte valt som standard. SSM Security Gör att du kan aktivera eller inaktivera ytterligare UEFI SMM-säkerhetsskydd. Operativsystemet kan använda Mitigation (SIMM- funktionen för att skydda den säkra miljön som skapas genom virtualiseringsbaserad säkerhet. säkerhetsbegräns SSM Security Mitigation (SSM-säkerhetsbegränsning) – Det här alternativet är inaktiverat som standard.
Alternativ Beskrivning • • • • Intel SpeedStep All (alla)Det här alternativet är aktiverat som standard. 1 2 3 Här kan du aktivera eller inaktivera processorläget Intel SpeedStep. • Enable Intel SpeedStep (aktivera Intel SpeedStep) Standardinställning: Alternativet är aktiverat. C-States Control Här kan du aktivera eller inaktivera de extra strömsparlägena för processorn. • C States (C-lägen) Standardinställning: Alternativet är aktiverat.
Alternativ Beskrivning • • Peak Shift Detta gör det möjligt att minimera strömförbrukningen under de mest strömslukande perioderna på dagen. När du har aktiverat det här alternativet drivs systemet endast med batteri även om nätsladden är ansluten. • Advanced Battery Charge Configuration Aktivera toppskiftDet här alternativet är inte valt som standard. Med det här alternativet kan du maximera batteritillståndet.
Alternativ Beskrivning Prompt on Warnings and Error (visa meddelande vid varningar och fel). Det här alternativet är aktiverat som standard. Continue on Warnings (fortsätt vid varningar) Sign of Life Indication Alternativ för virtualiseringsstöd Alternativ Beskrivning Virtualization Här kan du aktivera eller inaktivera Intel Virtualization-tekniken. Enable Intel Virtualization Technology (aktivera Intel Virtualization-tekniken) Det här alternativet är valt som standard.
Alternativ Beskrivning BIOS Recovery from Hard Drive (BIOS-återställning från hårddisken) – Det här alternativet är inställt som standard. Alternativ på systemloggskärmen Alternativ Beskrivning BIOS Events Här kan du visa och rensa BIOS-händelser under självtest. Thermal Events Här kan du visa och rensa termohändelser under självtest. Power Events Här kan du visa och rensa strömhändelser under självtest.
Nästa Steg OBS: Vi rekommenderar inte att du uppdaterar BIOS-versionen i större steg än tre revisioner i taget. Till exempel: Om du vill uppdatera BIOS från 1.0 till 7.0 ska du först installera version 4.0 och därefter version 7.0. Uppdatera system-BIOS med hjälp av en USBflashenhet Om denna uppgift Om systemet inte kan läsas in i Windows, men du ändå behöver uppdatera BIOS, hämtar du BIOS-filen med hjälp av ett annat system och sparar den på en startbar USB-flashenhet.
Du kan skapa ett systemlösenord och ett installationslösenord för att skydda datorn. CAUTION: Lösenordsfunktionerna ger dig en grundläggande säkerhetsnivå för informationen på datorn. CAUTION: Vem som helst kan komma åt informationen som är lagrad på datorn om den inte är låst och lämnas utan tillsyn. OBS: Funktionen för system- och installationslösenord är inaktiverad.
OBS: Om du ändrar system- och/eller installationslösenordet anger du det nya lösenordet igen när du uppmanas till det. Om du tar bort ett system- och installationslösenordet ska du bekräfta borttagningen när du uppmanas göra det. 5. Tryck på Esc så blir du ombedd att spara ändringarna. 6. Tryck på Y för att spara ändringarna och avsluta systeminstallationsprogrammet. Datorn startar om.
4 Felsökning Förbättrad systemutvärdering före start – eDiags2.0 eDiags 2.0 är ett diagnostiskt verktyg som är tillgängligt på surfplattan. Verktyget inkluderar en serie tester av surfplattans maskinvara. Kunder kan köra testerna även om datorn saknar media (hårdisk, CD-enhet etc.). Om en eDiags 2.0-testad komponent havererar visar systemet en felkod och genererar en ljudkod. Funktioner: • • • • • • • • • Grafiskt användargränssnitt.
Ström- och batteristatuslampa blinkar till exempel orange två gånger följt av en paus och blinkar sedan vitt tre gånger följt av en paus. Det här 2-3-mönstret upprepas tills datorn stängs av och indikerar att inget minne eller RAM detekteras. I följande tabell visas ljusmönster för olika ström- och batteristatus samt tillhörande problem. Tabell 2.
Driftsekvens 1 – utfällbart stöd Strömstatusändring 2 – Folio KB S0 MS S4 **G3/S5 övergå till öppen. I annat fall återgår systemet till systemvila/avstängt läge. Flash-uppdatera BIOS (USB-minne) Steg 1. Följ proceduren från steg 1 till steg 7 i "Uppdatera BIOS" om du vill hämta senaste BIOSinstallationsprogramfilen. 2. Skapa ett startbart USB-minne. Det finns mer information i kunskapsbas-artikeln SLN143196 på www.dell.com/support. 3.
Steg 1. Stäng av datorn. 2. Stäng av modemet. 3. Stäng av den trådlösa routern. 4. Vänta 30 sekunder. 5. Slå på den trådlösa routern. 6. Slå på modemet. 7. Starta datorn. Ladda ur väntelägesström Om denna uppgift Väntelägesström är statisk elektricitet som ligger kvar i datorn även efter att den har stängts av och batteriet har tagits bort. Följande procedur innehåller instruktioner för hur du laddar ur väntelägesströmmen: Steg 1. Stäng av datorn. 2. Koppla bort strömadaptern från datorn. 3.
5 Få hjälp Ämnen: • Kontakta Dell Kontakta Dell Förutsättningar OBS: Om du inte har en aktiv Internet-anslutning kan du hitta kontaktinformationen på ditt inköpskvitto, förpackning, faktura eller i Dells produktkatalog. Om denna uppgift Dell erbjuder flera alternativ för support och service online och på telefon. Tillgängligheten varierar beroende på land och produkt och vissa tjänster kanske inte finns i ditt område.