Latitude 7320 서비스 매뉴얼 규정 모델: P133G/P134G 규정 유형: P133G001/P134G001 January 2021 개정 A00
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자의 상표 일 수 있습니다.
목차 장 1: 컴퓨터에서 작업하기................................................................................................................. 6 안전 지침................................................................................................................................................................................6 서비스 모드......................................................................................................................................................................6 컴퓨터 내부 작업을 시작하기 전에...
오디오 보드 설치.......................................................................................................................................................... 39 스피커...................................................................................................................................................................................40 스피커 제거..........................................................................................................................................................
BIOS 플래싱.........................................................................................................................................................................78 Wi-Fi 전원 주기................................................................................................................................................................... 78 BIOS recovery.............................................................................................................................................
1 컴퓨터에서 작업하기 주제: • 안전 지침 안전 지침 전제조건 컴퓨터의 손상을 방지하고 안전하게 작업하기 위해 다음 안전 지침을 따르십시오. 특별히 언급하지 않는 한 이 문서에 포함된 각 절차 에서는 다음과 같은 조건을 전제하고 있음을 유의하십시오. ● 컴퓨터와 함께 제공된 안전 정보를 읽었습니다. ● 분리 절차를 역순으로 수행하여 구성 요소를 교체하거나 설치(별도로 구입한 경우)할 수 있습니다. 이 작업 정보 노트: 컴퓨터 덮개 및 패널을 열기 전에 전원을 모두 분리합니다. 컴퓨터 내부에서 작업한 후에는 전원을 연결하기 전에 덮개, 패 널 및 나사를 전부 장착합니다. 경고: 컴퓨터 내부 작업을 시작하기 전에 컴퓨터와 함께 제공된 안전 정보를 읽어보십시오. 추가 안전 모범 사례 정보는 규정 준 수 홈페이지를 참조하십시오. 주의: 대부분의 수리는 인증받은 서비스 기술 지원 담당자가 수행해야 합니다.
3. [소유자 태그로 구성된 모델의 경우] 소유자 태그 정보가 화면에 표시되면 아무 키나 눌러서 계속합니다. 노트: 제조업체에 의해 시스템의 소유자 태그가 미리 설정되지 않은 경우 서비스 모드 절차가 이 단계를 자동으로 건너뜁니 다. 4. AC 어댑터가 연결 해제되었는지 확인하고 아무 키나 눌러서 계속합니다.
5. 진행 준비 완료 메시지가 화면에 나타나면 아무 키나 눌러서 계속합니다. 시스템이 세 번의 짧은 비프음을 내고 즉시 종료됩니다. 시스템이 종료되면 배터리 케이블을 시스템 보드에서 연결 해제하지 않고 교체 절차를 수행할 수 있습니다. 서비스 모드를 종료하려면 AC 어댑터를 연결하고 전원 버튼을 눌러 시스템을 켭니다. 시스템이 자동으로 정상 작동 모드로 돌아갑니 다. 컴퓨터 내부 작업을 시작하기 전에 이 작업 정보 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 단계 1. 열려 있는 파일을 모두 저장하고 닫은 다음 사용 중인 응용 프로그램을 모두 종료합니다. 2. 컴퓨터를 종료하십시오. Start > Power > Shut down을 클릭합니다. 노트: 다른 운영 체제를 사용하고 있는 경우 해당 운영 체제의 설명서에서 종료 지침을 참조하십시오. 3. 컴퓨터 및 모든 연결된 디바이스를 전원 콘센트에서 연결 해제하십시오. 4.
대기 전력 대기 전력이 있는 Dell 제품은 케이스를 열기 전에 플러그를 뽑아야 합니다. 대기 전력이 있는 시스템은 기본적으로 시스템을 꺼도 전 력이 공급됩니다. 내부 전원을 사용하면 시스템을 원격으로 켜고(LAN을 통해 재개) 절전 모드로 둘 수 있습니다. 다른 고급 전원 관리 기능도 있습니다. 플러그를 뽑고 전원 버튼을 15초 동안 누르고 있으면 시스템 보드에서 잔여 전력이 방전됩니다. 태블릿에서 배터리를 제거합니다. 결합 결합은 2개 이상의 접지 전도체를 동일한 전위에 연결하는 방법으로, 현장 서비스 정전기 방전(ESD) 키트를 사용하여 수행합니다. 결 합 와이어를 연결할 때는 베어 메탈에 와이어를 연결해야 하며, 페인트를 칠한 표면이나 비금속 표면에 와이어를 연결해서는 안 됩니 다. 또한 손목 스트랩을 피부에 잘 고정하고 본인과 장비를 결합하기 전에 시계, 팔찌 또는 반지와 같은 모든 장신구를 빼야 합니다.
● ● ● ● ● 마모로 인해 손상되기 쉬우며 우발적인 ESD 하드웨어 손상을 방지하기 위해 손목 접지대 테스터를 사용하여 정기적으로 점검해 야 합니다. 손목 접지대와 본딩 와이어는 최소 일주일에 한 번 점검하는 것이 좋습니다. ESD 손목 접지대 테스터 – ESD 스트랩 내부의 전선은 시간이 경과하면 손상되기 쉽습니다. 모니터링되지 않는 키트를 사용하는 경우 각 서비스 콜을 이용하기 전에 최소 일주일에 한 번 스트랩을 정기적으로 검사하는 것이 좋습니다. 손목 접지대 테스터는 이 러한 테스트를 수행하는 가장 효과적인 방법입니다. 손목 접지대 테스터가 없는 경우 지역 사무소에 재고가 있는지 문의하십시 오. 테스트를 수행하려면, 손목 접지대의 본딩 와이어를 테스터에 연결하고 단추를 눌러 테스트를 시작합니다. 녹색 LED가 켜질 경우 테스트가 성공한 것이고, 빨간색 LED가 켜지거나 경고 소리가 나면 테스트에 실패한 것입니다.
2 구성 요소 제거 및 설치 노트: 이 문서의 이미지는 주문한 컴퓨터의 구성에 따라 조금씩 다를 수 있습니다. 주제: • • • • • • • • • • • • • • • • • • • • 권장 툴 나사 목록 주요 시스템 구성 요소 micro-SD 카드 SIM 카드 트레이 베이스 덮개 솔리드 스테이트 드라이브 WWAN 카드 배터리 방열판 조립품 팜레스트 안테나 모듈 디스플레이 어셈블리 오디오 보드 스피커 스마트 카드 판독기 시스템 보드 I/O 보드 지문 판독기가 장착된 전원 버튼 키보드 팜레스트 어셈블리 권장 툴 본 설명서의 절차를 수행하는 데 다음 도구가 필요합니다. ● Phillips #0 스크루 드라이버 ● 플라스틱 스크라이브: 현장 기술 지원 담당자에게 권장됩니다. 나사 목록 다음 표에는 나사 목록과 이미지가 나와 있습니다. 표 1.
표 1. 나사 목록 (계속) 구성 요소 나사 유형 수량 노트: 나사는 베이스 커버의 일부입니다. 솔리드 스테이트 드라이브 M2x2 2 WWAN M2x2.5 1 3셀 배터리 M2.5x4 1 조임 나사 4 방열판 어셈블리 M2x2.5 6 팜레스트 안테나 M2x2 1 M2x2.5 2 M2x2 3 M2.5x5 4 오디오 보드 M2x2.5 1 스마트 카드 리더 M2x2.5 3 시스템 보드 M2x3 9 M2x4 2 I/O 보드 M2x4 2 지문 인식기가 장착된 전원 버튼 M1.6x1.7 2 키보드 M1.6x1.
주요 시스템 구성 요소 1.
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 배터리 솔리드 스테이트 드라이브 실드 솔리드 스테이트 드라이브 시스템 보드 키보드 어셈블리 스마트 카드 리더 스피커 팜레스트 어셈블리 LCD 보드 디스플레이 어셈블리 I/O 보드 지문 인식기가 장착된 전원 버튼 WWAN 카드 실드 WWAN 카드 방열판 팜레스트 안테나 오디오 보드 노트: Dell은 구매한 원래 시스템 구성의 구성 요소 및 부품 번호 목록을 제공합니다. 이러한 부품은 고객이 구매한 보증 기간에 따라 사용할 수 있습니다. 구매 옵션은 Dell 영업 담당자에게 문의하십시오. micro-SD 카드 micro-SD 카드 제거 이 작업 정보 다음 이미지는 micro-SD 카드 리더 슬롯의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. micro-SD 카드를 눌러 슬롯에서 꺼냅니다. 2. micro-SD 카드를 컴퓨터에서 제거합니다.
micro-SD 카드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 micro-SD 카드 리더 슬롯의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다. 단계 딸깍 소리를 내며 제자리에 끼워질 때까지 micro-SD 카드를 해당 슬롯에 삽입합니다. SIM 카드 트레이 SIM 카드 트레이 제거 전제조건 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 이 작업 정보 다음 이미지는 SIM 카드 트레이 제거 절차를 시각적으로 보여줍니다.
단계 1. 릴리스 구멍에 핀을 삽입하여 SIM 카드 트레이를 릴리스합니다. 2. 핀을 밀어 잠금 장치를 분리하고 SIM 카드 트레이를 꺼냅니다. 3. SIM 카드 트레이를 밀어 시스템의 슬롯에서 꺼냅니다. 4. SIM 카드 트레이에서 SIM 카드를 제거합니다. 5. SIM 카드 트레이를 슬롯에 다시 밀어 넣습니다. SIM 카드 트레이 설치 전제조건 구성 요소를 교체하는 경우 설치 절차 전에 필수 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 SIM 카드 트레이 설치 절차를 시각적으로 보여줍니다.
단계 1. SIM 카드를 SIM 카드 트레이의 전용 슬롯에 맞추어 넣습니다. 2. SIM 카드 트레이를 시스템의 슬롯에 밀어 넣고[6] 밀어서 제자리에 고정합니다. 다음 단계 컴퓨터 작업을 마친 후에의 절차를 따릅니다. 베이스 덮개 베이스 커버 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 3. 서비스 모드로 전환합니다.
이 작업 정보 18 구성 요소 제거 및 설치
단계 1. 베이스 커버를 컴퓨터에 고정하는 8개의 조임 나사를 풉니다. 2. 플라스틱 스크라이브를 사용하여 베이스 커버를 베이스 커버 상단 가장자리의 힌지 근처에 있는 U자형 리세스부터 들어 올려 엽 니다. 주의: 플라스틱 스크라이브가 베이스 커버 내부의 래치를 손상시키므로 베이스 커버의 상단 가장자리를 통해 플라스틱 스크 라이브를 밀어 넣지 마십시오. 3. 베이스 커버의 좌측 및 우측을 들어 올려 엽니다. 4. 베이스 커버의 하단을 들어 올려 엽니다. 5. 베이스 커버의 왼쪽 및 오른쪽 측면을 잡고 컴퓨터에서 제거합니다. 베이스 커버 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 베이스 커버의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 베이스 커버를 컴퓨터에 맞추어 놓고 베이스 커버 래치를 제자리에 끼워 넣습니다.
2. 베이스 커버를 컴퓨터에 고정하는 8개의 조임 나사를 조입니다. 다음 단계 1. microSD 카드를 설치합니다. 2. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 솔리드 스테이트 드라이브 솔리드 스테이트 드라이브 제거 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 서비스 모드로 전환합니다. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 솔리드 스테이트 드라이브의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. SSD 실드를 고정하는 2개의 나사(M2x2)를 제거하고 실드를 SSD에서 제거합니다. 2. 솔리드 스테이트 드라이브를 밀어 시스템 보드의 M.2 슬롯에서 제거합니다. 노트: SSD 플레이트에 포함된 열 패드는 항상 플레이트에 부착되어 있어야 합니다.
이 작업 정보 다음 이미지는 솔리드 스테이트 드라이브의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. SSD의 노치를 M.2 슬롯의 탭에 맞추고 SSD를 시스템 보드의 M.2 카드 슬롯에 밀어 넣습니다. 2. SSD 실드를 장착하고 단단히 끼워지도록 눌러 SSD를 덮고 2개의 M2x2 나사로 고정합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. WWAN 카드 WWAN 카드 제거 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 서비스 모드로 전환합니다. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 WWAN 카드의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 1. 플라스틱 스크라이브를 사용하여 WWAN 카드를 덮은 WWAN 카드 실드를 들어 올려 제거합니다. 노트: WWAN 카드 실드를 왼쪽 상단의 리세스에서 들어 올려 엽니다. 2. 1개의 M2x2.5 나사를 풀고 WWAN 카드 브래킷을 제거합니다. 3. 안테나 케이블을 WWAN 카드의 커넥터에서 연결 해제합니다. 4. WWAN 카드를 밀어내 시스템 보드의 M.2 슬롯에서 제거합니다.
WWAN 카드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 WWAN 카드의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다. 단계 1. WWAN 카드의 노치를 WWAN 카드 슬롯의 탭에 맞추고 WWAN을 시스템 보드의 M.2 슬롯에 밀어 넣습니다. 2. 안테나 케이블을 WWAN 카드의 커넥터에 연결합니다. 3. WWAN 카드 브래킷을 맞추어 놓고 1개의 M2x2.5 나사를 조여 시스템 보드에 고정합니다. 4. WWAN 카드 실드를 WWAN 카드 위에 장착합니다. 노트: WWAN 카드 실드의 가장자리를 시스템 보드의 클립에 삽입하여 제자리에 고정합니다.
다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 배터리 리튬 이온 배터리 예방 조치 주의: ● 리튬 이온 배터리를 다룰 때는 주의하십시오. ● 배터리를 제거하기 전에 완전히 방전시키십시오. 시스템에서 AC 전원 어댑터의 연결을 해제하고 배터리 전원으로만 컴퓨터 를 작동시킵니다. 전원 버튼을 눌렀을 때 컴퓨터가 더 이상 켜지지 않으면 배터리가 완전히 방전된 것입니다. ● 배터리를 찌그러뜨리거나 떨어뜨리거나 훼손하거나 외부 개체로 배터리에 구멍을 뚫지 마십시오. ● 고온에 배터리를 노출하거나 배터리 팩과 셀을 분해하지 마십시오. ● 배터리 표면에 압력을 가하지 마십시오. ● 배터리를 구부리지 마십시오. ● 툴을 사용해 배터리를 꺼내려 하거나 배터리에 힘을 가하지 마십시오.
단계 1. 시스템 보드에서 배터리 케이블을 분리합니다. 2. 스피커 케이블을 스피커 보드에서 연결 해제하고 스피커 케이블을 배터리 상단 우측 너머 라우팅 가이드에서 분리합니다. 3. 배터리를 컴퓨터에 고정하는 1개의 M2.5x4 나사와 4개의 캡티브 나사를 제거합니다. 4. 배터리를 들어 올려 컴퓨터에서 제거합니다. 3셀 배터리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 배터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
노트: 배터리가 시스템 보드에서 연결 해제된 경우 컴퓨터가 RTC 재설정을 진행하며 컴퓨터 부팅 중 지연이 발생합니다. 단계 1. 배터리를 컴퓨터에 맞추어 넣습니다. 2. 1개의 M2.5x4 나사와 4개의 캡티브 나사를 설치하여 배터리를 제자리에 고정합니다. 3. 스피커 케이블을 스피커 보드에 연결하고 스피커 케이블을 배터리 상단 우측 너머 해당 라우팅 채널에 다시 라우팅합니다. 4. 배터리 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
4셀 배터리 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 3. 베이스 커버를 제거합니다. 노트: 배터리가 시스템 보드에서 연결 해제된 경우 컴퓨터가 RTC 재설정을 진행하며 컴퓨터 부팅 중 지연이 발생합니다. 이 작업 정보 다음 이미지는 배터리의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 시스템 보드에서 배터리 케이블을 분리합니다. 2. 스피커 케이블을 스피커 보드에서 연결 해제하고 스피커 케이블을 배터리 상단 우측 너머 해당 라우팅 채널에서 라우팅 해제합니 다. 3. 배터리를 컴퓨터에 고정하는 4개의 캡티브 나사를 제거합니다. 4. 배터리를 들어 올리고 배터리를 컴퓨터에서 제거합니다. 4셀 배터리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 배터리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
노트: 배터리가 시스템 보드에서 연결 해제된 경우 컴퓨터가 RTC 재설정을 진행하며 컴퓨터 부팅 중 지연이 발생합니다. 단계 1. 배터리를 컴퓨터에 맞추어 넣습니다. 2. 4개의 캡티브 나사를 설치하여 배터리를 제자리에 고정합니다. 3. 스피커 케이블을 스피커 보드에 연결하고 스피커 케이블을 배터리 상단 우측 너머 해당 라우팅 채널에 다시 라우팅합니다. 4. 배터리 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 방열판 조립품 방열판 어셈블리 제거 전제조건 1. 2. 3. 4. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 서비스 모드로 전환합니다. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 방열판 어셈블리의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 1. 시스템 보드에서 팬 케이블을 분리합니다. 2. 팬 케이스에서 2개의 M2x2.5 나사를 제거하고 방열판을 컴퓨터에 고정하는 4개의 M2x2.5 나사를 4->3->2->1 역순으로 제거합니 다. 3. 방열판 어셈블리를 컴퓨터에서 들어 올립니다. 방열판 어셈블리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 방열판 어셈블리의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다.
단계 1. 방열판 어셈블리를 컴퓨터의 해당 슬롯에 맞추어 넣습니다. 2. 2개의 M2x2.5 나사를 팬 케이스에 장착하고 4개의 M2x2.5 나사를 1->2->3->4 순서로 장착하여 방열판 어셈블리를 컴퓨터에 고정 합니다. 3. 팬 케이블을 시스템 보드에 연결합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 팜레스트 안테나 모듈 팜레스트 안테나 모듈 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 3. 베이스 커버를 제거합니다. 이 작업 정보 다음 이미지는 팜레스트 안테나 모듈의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 1. 팜레스트 브래킷을 시스템 보드에 고정하는 M2x2 나사를 제거합니다. 2. 시스템 보드의 WLAN 모듈에 연결된 안테나 케이블을 연결 해제하고 라우팅 해제합니다. 3. 팜레스트 안테나를 시스템에 고정하는 2개의 M2x2.5 나사를 제거합니다. 4. 팜레스트 안테나 모듈을 들어 올려 시스템에서 분리합니다. 팜레스트 안테나 모듈 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 팜레스트 안테나 모듈의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다.
단계 1. 팜레스트 안테나 모듈을 시스템에 놓고 이를 시스템에 고정하는 2개의 M2x2.5 나사를 장착합니다. 2. 안테나 케이블을 라우팅 채널을 통해 다시 라우팅하고 시스템 보드의 WLAN 모듈에 연결합니다. 3. WLAN 브래킷을 시스템 보드에 고정하는 M2x2 나사를 장착합니다. 다음 단계 1. 베이스 커버를 설치합니다. 2. microSD 카드를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 어셈블리 디스플레이 어셈블리 제거 전제조건 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 서비스 모드로 전환합니다. 베이스 커버를 제거합니다. WWAN 카드를 제거합니다. 이 작업 정보 다음 그림은 디스플레이 어셈블리의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
구성 요소 제거 및 설치
단계 1. 디스플레이 케이블 브래킷을 시스템 보드에 고정하는 2개의 M2x2를 제거합니다. 2. 디스플레이 케이블 브래킷을 들어 올려 컴퓨터에서 제거합니다. 3. 디스플레이, 카메라, 터치스크린, 센서 보드 케이블을 시스템 보드에서 연결 해제하고 케이블 가이드 탭에서 분리합니다. 4. 디스플레이 덮개를 90º도로 열고 힌지를 팜레스트 어셈블리에 고정하는 4개의 M2.5x5 나사를 제거합니다. 5. 컴퓨터에서 디스플레이 조립품을 분리합니다. 노트: 참고: 디스플레이 어셈블리는 HUD(Hinge-Up Design) 어셈블리로, 하단 섀시에서 제거한 후에는 더 이상 분해할 수 없습 니다. 디스플레이 어셈블리의 구성 요소가 제대로 작동하지 않아 교체가 필요하면 전체 디스플레이 어셈블리를 교체하십시 오.
그림 1 . 안테나 케이블이 있는 디스플레이 어셈블리 디스플레이 어셈블리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 이 그림은 디스플레이 어셈블리의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
구성 요소 제거 및 설치 37
단계 1. 디스플레이 어셈블리를 편한 각도로 하단 섀시에 맞추어 놓습니다. 2. 힌지를 하단 섀시에 고정하는 4개의 M2.5x5 나사를 장착합니다. 3. 디스플레이 케이블을 가이드 탭을 따라 라우팅하고 디스플레이, 카메라, 터치스크린, 센서 보드 케이블을 시스템 보드에 연결합니 다. 4. 디스플레이 케이블 브래킷을 시스템 보드의 커넥터에 맞추어 놓습니다. 5. 디스플레이 케이블 브래킷을 시스템 보드에 고정하는 2개의 M2x2 나사를 설치합니다. 다음 단계 1. WWAN 카드를 설치합니다. 2. 베이스 커버를 설치합니다. 3. microSD 카드를 설치합니다. 4. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 오디오 보드 오디오 보드 제거 전제조건 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 서비스 모드로 전환합니다. microSD 카드를 제거합니다. 베이스 커버를 제거합니다. 배터리를 제거합니다.
단계 1. 오디오 보드 FFC를 시스템 보드에서 연결 해제하고 떼어냅니다. 2. 오디오 보드를 컴퓨터에 고정하는 M2x2.5 나사를 제거합니다. 3. 오디오 보드를 들어 올려 컴퓨터에서 제거합니다. 오디오 보드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 그림은 오디오 보드의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다.
단계 1. 오디오 보드를 컴퓨터의 해당 슬롯에 맞추어 장착합니다. 2. M2x2.5 나사를 장착하여 오디오 보드를 컴퓨터에 고정합니다. 3. 오디오 보드 FFC를 시스템 보드에 연결합니다. 다음 단계 1. 배터리를 설치합니다. 2. 베이스 커버를 설치합니다. 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 스피커 스피커 제거 전제조건 1. 2. 3. 4. 40 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 커버를 제거합니다. 배터리를 제거합니다.
이 작업 정보 다음 이미지는 스피커의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 케이블을 팜레스트 어셈블리의 탭에서 분리합니다. 2. 스피커를 들어 올려 컴퓨터 섀시에서 제거합니다. 스피커 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 스피커의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다.
단계 1. 스피커를 컴퓨터의 슬롯에 장착합니다. 2. 스피커 케이블을 팜레스트 어셈블리의 케이블 가이드를 따라 라우팅합니다. 노트: 스피커 교체 시 스피커 케이블을 팜레스트 어셈블리 하단을 따라 라우팅 채널 안으로 라우팅하십시오. 스피커 케이블을 LED 보드 FFC 너머로 라우팅하고 팜레스트 및 터치패드에 부착된 테이프로 제자리에 고정합니다. 다음 단계 1. 2. 3. 4. 42 배터리를 설치합니다. 베이스 커버를 설치합니다. microSD 카드를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
스마트 카드 판독기 스마트 카드 리더 제거 전제조건 1. 2. 3. 4. 5. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. 베이스 커버를 제거합니다. 배터리를 제거합니다. 스피커를 분리합니다. 이 작업 정보 다음 이미지는 스마트 카드 리더의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 터치패드 모듈을 연결 해제하고 FFC 케이블을 터치패드 모듈 위에서 떼어냅니다. 2. 스마트 카드 리더 및 NFC 모듈 케이블을 USH 보드에서 연결 해제합니다.
3. 3개의 M2x2.5 나사를 제거하고 스마트 카드 리더를 섀시의 해당 슬롯에서 밀어냅니다. 스마트 카드 리더 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 스마트 카드 리더의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다. 단계 1. 스마트 카드 리더를 컴퓨터 섀시의 해당 슬롯에 밀어 넣고 3개의 M2x2.5 나사를 사용하여 고정합니다. 2. 스마트 카드 리더와 NFC 모듈 케이블을 연결하고 USH 보드에 연결합니다. 3. 터치패드 FFC 케이블을 터치패드 모듈의 측면을 따라 연결하고 시스템 보드에 연결합니다. 다음 단계 1. 스피커를 설치합니다. 2. 배터리를 설치합니다.
3. 베이스 커버를 설치합니다. 4. microSD 카드를 설치합니다. 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 시스템 보드 시스템 보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 서비스 모드로 전환합니다. microSD 카드를 제거합니다. SIM 카드를 제거합니다. 베이스 커버를 제거합니다. 솔리드 스테이트 드라이브를 제거합니다. 배터리를 제거합니다. WWAN 카드를 제거합니다. 방열판 어셈블리를 제거합니다. 주의: 시스템 보드를 컴퓨터에 고정하는 2개의 M2x3 나사가 방열판 아래에 있으므로 시스템 보드를 제거하기 전에 방열판 어셈블리를 제거하십시오. 노트: 탄소섬유 팜레스트가 있고 WWAN 안테나가 없는 구성의 경우 시스템 보드를 제거하기 전에 더미 SIM 카드 트레이를 시스템에서 제거해야 합니다. 더미 SIM 카드 트레이를 제거하려면 릴리스 래치를 안으로 민 다음 더미 카드 트레이를 컴퓨터에서 밀어냅니다.
구성 요소 제거 및 설치
단계 1. M2x2.5 나사를 제거하고 WWAN 안테나 케이블 브래킷을 들어 올립니다. 2. WWAN 안테나 케이블을 연결 해제하고 케이블을 시스템 보드의 고무 가이드에서 분리합니다. 3. 1개의 M2x2.5 나사를 지문 인식기 브래킷에서 제거하고 브래킷을 컴퓨터에서 제거합니다. 4. 지문 인식기 FPC를 시스템 보드에서 연결 해제합니다. 5. 1개의 M2x2 나사를 제거하고 브래킷을 안테나 케이블에서 들어 올립니다. 6. WLAN 안테나 케이블을 시스템 보드의 WLAN 모듈에서 연결 해제합니다. 7. 디스플레이 케이블 브래킷을 시스템 보드에 고정하는 2개의 M2x2 나사를 제거합니다. 8. 디스플레이 케이블 브래킷을 들어 올려 컴퓨터에서 제거합니다. 9. 디스플레이, 카메라, 터치스크린, 센서 보드 케이블을 시스템 보드에서 연결 해제하고 가이드 탭에서 라우팅 해제합니다. 10.
단계 1. 시스템 보드를 컴퓨터 섀시에 장착하고 1개의 M2x2.5나사(전원 버튼에 지문 인식기가 있는 컴퓨터 구성) 또는 2개의 M2x2.5 나사 (지문 인식기가 없는 컴퓨터 구성), 2개의 M2x4 나사 및 2개의 M2x3 나사로 조여 시스템 보드를 제자리에 고정합니다. 2. 스피커 보드 FPC, 트위터 케이블, 오디오 보드 FFC, 터치패드 FFC, USH 보드 FFC 및 LED 보드 FFC를 시스템 보드에 연결합니다. 3. 디스플레이, 카메라, 터치스크린, 센서 보드 케이블을 시스템 보드에 연결하고 가이드 탭을 따라 라우팅합니다. 4. 디스플레이 케이블 브래킷을 시스템 보드에 장착하고 2개의 M2x2 나사로 고정합니다. 5. WLAN 안테나 케이블을 시스템 보드의 WLAN 모듈에 연결합니다. 6. WLAN 안테나 브래킷을 장착하고 1개의 M2x2 나사를 사용하여 시스템 보드에 고정합니다. 7. 지문 인식기 FPC를 시스템 보드에 연결합니다. 8. 지문 인식기 브래킷을 장착하고 1개의 M2x2.
8. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. I/O 보드 I/O 보드 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 서비스 모드로 전환합니다. microSD 카드를 제거합니다. SIM 카드를 제거합니다. 베이스 커버를 제거합니다. 솔리드 스테이트 드라이브를 제거합니다. WWAN 카드를 제거합니다. 배터리를 제거합니다. 방열판 어셈블리를 제거합니다. 시스템 보드를 제거합니다. 이 작업 정보 다음 이미지는 I/O 보드의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. I/O 보드를 컴퓨터에 고정하는 2개의 M2x4 나사를 제거합니다. 2. I/O 보드를 들어 올려 컴퓨터에서 제거합니다.
I/O 보드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 I/O 보드의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. I/O 보드를 컴퓨터의 해당 슬롯에 장착합니다. 2. 2개의 M2x4 나사를 사용하여 I/O 보드를 컴퓨터에 고정합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 시스템 보드를 설치합니다. 방열판 어셈블리를 설치합니다. 배터리를 설치합니다. WWAN 카드를 설치합니다. 솔리드 스테이트 드라이브를 설치합니다. 베이스 커버를 설치합니다. SIM 카드를 설치합니다. microSD 카드를 설치합니다. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
지문 판독기가 장착된 전원 버튼 지문 인식기가 탑재된 전원 버튼 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 서비스 모드로 전환합니다. microSD 카드를 제거합니다. SIM 카드를 제거합니다. 베이스 커버를 제거합니다. 솔리드 스테이트 드라이브를 제거합니다. WWAN 카드를 제거합니다. 배터리를 제거합니다. 방열판 어셈블리를 제거합니다. 시스템 보드를 제거합니다. 이 작업 정보 다음 이미지는 지문 인식기가 탑재된 전원 버튼의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다. 단계 1. 지문 인식기가 탑재된 전원 버튼을 컴퓨터에 고정하는 2개의 M1.6x1.7 나사를 제거합니다. 2. 지문 인식기가 탑재된 전원 버튼을 들어 올려 컴퓨터에서 제거합니다. 지문 인식기가 장착된 전원 버튼 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다.
이 작업 정보 다음 그림은 지문 판독기가 장착된 전원 버튼의 위치를 나타내고 설치 절차를 시각적으로 보여 줍니다. 단계 1. 지문 인식기가 장착된 전원 버튼을 컴퓨터의 해당 슬롯에 장착합니다. 2. 2개의 M1.6x1.7 나사를 사용하여 지문 인식기가 장착된 전원 버튼을 컴퓨터에 고정합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 시스템 보드를 설치합니다. 방열판 어셈블리를 설치합니다. 배터리를 설치합니다. WWAN 카드를 설치합니다. 솔리드 스테이트 드라이브를 설치합니다. 베이스 커버를 설치합니다. SIM 카드를 설치합니다. microSD 카드를 설치합니다. 노트: 컴퓨터를 켜기 전에 AC 전원을 연결합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 키보드 키보드 제거 전제조건 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. microSD 카드를 제거합니다. 3. 베이스 커버를 제거합니다.
4. 5. 6. 7. 8. 9. 10. 솔리드 스테이트 드라이브를 제거합니다. WWAN 카드를 제거합니다. 배터리를 제거합니다. 방열판 어셈블리를 제거합니다. 오디오 보드를 제거합니다. 시스템 보드를 제거합니다. I/O 보드를 분리합니다. 이 작업 정보 다음 이미지는 키보드의 위치를 나타내고 제거 절차를 시각적으로 보여줍니다.
단계 1. LED 보드 FFC, USH 보드 FFC, 터치패드 FFC 및 스마트 카드 리더 FFC를 키보드 후면에서 떼어냅니다. 2. 키보드 FPC 및 키보드 백라이트 FPC 를 터치패드 모듈에서 연결 해제합니다. 3. 키보드 어셈블리를 컴퓨터에 고정하는 18개의 M1.6x1.7 나사를 제거합니다. 4. 키보드 어셈블리를 조심스럽게 들어 올려 컴퓨터에서 제거합니다. 5. 키보드를 키보드 지지판에 고정하는 2개의 M2x2 나사를 제거합니다. 6. 키보드를 키보드 지지판에서 분리합니다. 키보드 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다. 이 작업 정보 다음 이미지는 키보드의 위치를 나타내고 설치 절차를 시각적으로 보여줍니다.
구성 요소 제거 및 설치 55
단계 1. 키보드를 키보드 지지판에 맞추어 놓고 2개의 M2x2 나사를 사용하여 고정합니다. 2. 키보드 어셈블리르 컴퓨터의 해당 슬롯에 장착합니다. 3. 키보드 FPC 및 키보드 백라이트 FPC를 터치패드 모듈에 연결합니다. 4. 키보드 어셈블리를 컴퓨터에 고정하는 18개의 M1.6x1.7 나사를 장착합니다. 5. LED 보드 FFC, USH 보드 FFC, 터치패드 FFC 및 스마트 카드 리더 FFC를 키보드 후면에 연결합니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 56 I/O 보드를 설치합니다. 시스템 보드를 설치합니다. 오디오 보드를 설치합니다. 방열판 어셈블리를 설치합니다. 배터리를 설치합니다. WWAN 카드를 설치합니다. 솔리드 스테이트 드라이브를 설치합니다. 베이스 커버를 설치합니다. microSD 카드를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
팜레스트 어셈블리 손목 받침대 어셈블리 제거 전제조건 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. microSD 카드를 제거합니다. SIM 카드를 제거합니다. 베이스 커버를 제거합니다. 솔리드 스테이트 드라이브를 제거합니다. WWAN 카드를 제거합니다. 배터리를 제거합니다. 방열판 어셈블리를 제거합니다. 디스플레이 어셈블리를 제거합니다. 스피커를 분리합니다. 스마트 카드 리더를 제거합니다. 오디오 보드를 제거합니다. 시스템 보드를 제거합니다. I/O 보드를 분리합니다. 지문 인식기가 장착된 전원 버튼을 제거합니다. 키보드를 분리합니다. 단계 사전 요구 단계를 수행하고 나면 팜레스트 어셈블리가 남습니다. 팜레스트 어셈블리 설치 전제조건 구성 요소를 교체하는 경우 설치 절차를 수행하기 전에 기존 구성 요소부터 제거합니다.
단계 1. 팜레스트 어셈블리를 평평한 표면에 놓습니다. 2. 구성 요소를 새 팜레스트 어셈블리로 옮깁니다. 다음 단계 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 58 키보드를 설치합니다. 지문 인식기가 장착된 전원 버튼을 설치합니다. I/O 보드를 설치합니다. 시스템 보드를 설치합니다. 오디오 보드를 설치합니다. 스마트 카드 리더를 설치합니다. 스피커를 설치합니다. 디스플레이 어셈블리를 설치합니다. 방열판 어셈블리를 설치합니다. 배터리를 설치합니다. WWAN 카드를 설치합니다. 솔리드 스테이트 드라이브를 설치합니다. 베이스 커버를 설치합니다. SIM 카드를 설치합니다. microSD 카드를 설치합니다. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
3 소프트웨어 이 장에서는 드라이버 설치 방법에 대한 지침과 함께 지원되는 운영 체제를 자세하게 설명합니다. 주제: • Windows 드라이버 다운로드 Windows 드라이버 다운로드 단계 1. 노트북의 전원을 켭니다. 2. Dell.com/support로 이동합니다. 3. 제품 지원을 클릭해 노트북의 서비스 태그를 입력한 후 제출을 클릭합니다. 노트: 서비스 태그가 없는 경우 자동 감지 기능을 사용하거나 수동으로 노트북 모델을 찾습니다. 4. Drivers and Downloads(드라이버 및 다운로드)를 클릭합니다. 5. 노트북에 설치된 운영 체제를 선택합니다. 6. 페이지 아래로 스크롤해서 설치할 드라이버를 선택합니다. 7. 파일 다운로드를 클릭하여 노트북용 드라이버를 다운로드합니다. 8. 다운로드가 완료된 후 드라이버 파일을 저장한 폴더로 이동합니다. 9. 드라이버 파일 아이콘을 두 번 클릭하고 화면의 지침을 따릅니다.
4 시스템 설정 주의: 컴퓨터 전문가가 아닌 경우 BIOS 설정 프로그램의 설정을 변경하지 마십시오. 일부 변경 시 컴퓨터가 올바르게 작동하지 않을 수 있습니다. 노트: BIOS 설정 프로그램을 변경하기 전에 나중에 참조할 수 있도록 BIOS 설정 프로그램 화면 정보를 기록해 두는 것이 좋습니 다. BIOS 설정 프로그램은 다음과 같은 용도로 사용합니다. ● 컴퓨터에 설치된 하드웨어의 정보 찾기(예: RAM 용량, 하드 드라이브 크기 등) ● 시스템 구성 정보를 변경합니다.
탐색 키 노트: 대부분의 변경한 시스템 설정 옵션과 변경 사항은 기록되지만, 시스템을 다시 시작하기 전까지는 적용되지 않습니다. 키 탐색기 위쪽 화살표 이전 필드로 이동합니다. 아래쪽 화살표 다음 필드로 이동합니다. Enter 선택한 필드에서 값을 선택하거나(해당하는 경우) 필드의 링크로 이동합니다. 스페이스바 드롭다운 목록(있는 경우)을 확장하거나 축소합니다. 탭 다음 작업 영역으로 이동합니다. Esc 기본 화면이 보일 때까지 이전 페이지로 이동합니다. 기본 화면에서 Esc 키를 누르면 저장하지 않은 변경 사항 을 저장하고 시스템을 다시 시작하라는 메시지가 표시됩니다. Boot Sequence 부팅 순서를 사용하여 시스템 설치가 정의하는 부트 디바이스 순서를 생략하고 직접 특정 디바이스(예: 옵티컬 드라이브 또는 하드 드라이브)로 부팅할 수 있습니다. POST(Power-on Self Test) 중에 Dell 로고가 나타나면 다음 작업을 수행할 수 있습니다.
표 2. 시스템 설치 옵션- 시스템 정보 메뉴 (계속) 개요 기본 주 배터리를 표시합니다. 배터리 레벨 시스템의 배터리 잔량을 표시합니다. 배터리 상태 시스템의 배터리 상태를 표시합니다. 상태 시스템의 배터리 노화 상태를 표시합니다. AC 어댑터 AC 어댑터의 연결 여부를 표시합니다. 배터리 유형 배터리의 유형을 표시합니다. 프로세서 정보 프로세서 유형 프로세서 유형을 표시합니다. 최대 클록 속도 프로세서의 최대 클록 속도를 표시합니다. 최소 클록 속도 프로세서의 최소 클록 속도를 표시합니다. 현재 클록 속도 프로세서의 현재 클록 속도를 표시합니다. 코어 개수 프로세서의 코어 수를 표시합니다. Processor ID 프로세서 확인 코드를 표시합니다. 프로세서 L2 캐시 프로세서 L2 캐시 크기를 표시합니다. 프로세서 L3 캐시 프로세서 L3 캐시 크기를 표시합니다. 마이크로코드 버전 마이크로코드 버전을 표시합니다.
표 3. 시스템 설정 옵션 - 부팅 구성 메뉴 부팅 구성 부트 순서 Boot Mode(부팅 모드) 부팅 모드를 표시합니다. 부트 순서 부트 순서를 표시합니다. 보안 디지털(SD) 카드 부팅 SD 카드 읽기 전용 부팅을 활성화하거나 비활성화합니다. 기본적으로 SD(Secure Digital) 카드 부팅 옵션은 활성화되어 있지 않습니다. 보안 부팅 보안 부팅 활성화 보안 부팅 기능을 활성화 또는 비활성화합니다. 기본적으로 이 옵션은 활성화되어 있지 않습니다. 보안 부팅 모드 보안 부팅 모드 옵션 변경을 활성화하거나 비활성화합니다. 기본적으로 배포 모드는 활성화되어 있습니다. Expert Key Management Enable Custom Mode 사용자 지정 모드를 활성화 또는 비활성화합니다. 기본적으로 사용자 지정 모드 옵션은 활성화되어 있지 않습니다. 사용자 지정 모드 키 관리 전문 키 관리에 대한 사용자 지정 값을 선택합니다. 표 4.
표 4. 시스템 설정 옵션 - 내장형 디바이스 메뉴 (계속) 내장형 디바이스 Type-C 포트의 비디오/전원 전용 Type-C 포트 기능을 비디오 또는 전원 전용으로 활성화하거나 비활성화합니다. 기본적으로 Type-C 포트의 비디오/전원 전용 옵션은 비활성화되어 있습니다. Type-C 도크 재정의 외부 USB 포트가 비활성화된 상태로 연결된 Type-C Dell Dock를 사용하여 데이터 스트림을 제공하도록 활성화합니다. Type-C 도크 재정의를 활성화하면 비디오/오 디오/LAN 하위 메뉴가 활성화됩니다. 기본적으로 Type-C 도크 재정의 옵션은 활성화되어 있습니다. 비디오 Dell Dock 외부 포트의 비디오 사용을 활성화하거나 비활성화합니다. 기본적으로 비디오 옵션은 비활성화되어 있습니다. 오디오 Dell Dock 외부 포트의 오디오 사용을 활성화하거나 비활성화합니다. 기본적으로 오디오 옵션은 활성화되어 있습니다.
표 6. 시스템 설정 옵션 - 디스플레이 메뉴 디스플레이 디스플레이 밝기 배터리 전원 밝기 배터리 전원으로 작동하는 중인 시스템의 화면 밝기를 설정할 수 있습니다. AC 전원 밝기 AC 전원으로 작동하는 중인 시스템의 화면 밝기를 설정할 수 있습니다. 전체 화면 로고 전체 화면 로고를 활성화하거나 비활성화합니다. 기본적으로 이 옵션은 활성화되어 있지 않습니다. 표 7. 시스템 설정 옵션 - 연결 메뉴 연결 무선 디바이스 활성화 WWAN/GPS 내부 WWAN/GPS 디바이스를 활성화하거나 비활성화합니다. 이 옵션은 기본적으로 활성화되어 있습니다. WWAN 버스 모드 WWAN(Wireless Wan) 카드의 인터페이스 유형을 설정합니다. 기본적으로 버스 모드 PCIe 옵션은 활성화되어 있습니다. WLAN 내부 WLAN 디바이스를 활성화하거나 비활성화합니다. 이 옵션은 기본적으로 활성화되어 있습니다. Bluetooth 내부 Bluetooth 디바이스를 활성화하거나 비활성화합니다.
표 8. 시스템 설정 옵션 - 전원 메뉴 (계속) 전원 기본적으로 적응 옵션이 활성화되어 있습니다. 고급 구성 고급 배터리 충전 구성 활성화 고급 배터리 충전 구성을 활성화하거나 비활성화합니다. 기본적으로 고급 배터리 충전 구성 활성화 옵션은 비활성화되어 있습니다. Peak Shift 피크 전원 사용 시간 동안 시스템을 배터리로 작동할 수 있습니다. Enable Peak Shift(피크 전이 활성화) 기본적으로 피크 전이 활성화 옵션은 비활성화되어 있습니다. USB PowerShare USB PowerShare 사용 USB PowerShare를 활성화하거나 비활성화합니다. 기본적으로 USB PowerShare 활성화 옵션은 비활성화되어 있습니다. 열 관리 팬을 냉각하고 프로세서 열 관리를 활성화하여 시스템 성능, 소음 및 온도를 조정 합니다. 기본적으로 최적화 옵션이 활성화되어 있습니다.
표 9. 시스템 설치 옵션—보안 메뉴 (계속) 보안 기본적으로 지우기 명령의 PPI 무시 옵션은 비활성화되어 있습니다. 인텔 TME(Total Memory Encryption) TME(Total Memory Encryption) 냉각제, 주기를 읽기 위한 DDR 프로빙 등을 포함한 물리적 공격에서 메모리를 보 호하거나 보호하지 않을 수 있습니다. 기본적으로 TME(Total Memory Encryption) 옵션은 비활성화되어 있습니다. 섀시 침입 섀시 침입 기능을 제어합니다. 기본적으로 온사일런트 옵션이 활성화되어 있습니다. 침입 경고 해제 기본적으로 이 옵션은 비활성화되어 있습니다. SMM Security Mitigation SMM Security Mitigation을 활성화 또는 비활성화합니다. 이 옵션은 기본적으로 활성화되어 있습니다. 다음 부팅 시 데이터 지우기 데이터 지우기 시작 다음 부팅 시 데이터 지우기를 활성화하거나 비활성화합니다.
표 10. 시스템 설정 옵션 - 암호 메뉴 (계속) 암호 비관리자 암호 변경 활성화 관리자 암호 없이 시스템 및 하드 드라이브 암호를 변경하도록 활성화하거나 비활 성화합니다. 기본적으로 이 옵션은 비활성화되어 있습니다. Admin Setup Lockout Enable Admin Setup Lockout(관리자 설정 잠금 사용) 사용자의 BIOS 설정에 대한 액세스 가능 여부를 관리자가 제어할 수 있습니다. 기본적으로 이 옵션은 비활성화되어 있습니다. 마스터 암호 잠금 Enable Master Password Lockout(마스터 암 활성화 시 마스터 암호 지원이 비활성화됩니다. 호 잠금 활성화) 기본적으로 이 옵션은 비활성화되어 있습니다. 관리자 외 PSID 되돌리기 허용 관리자 외 PSID 되돌리기 허용을 활성화합 니다. Dell Security Manager 프롬프트에서 NVMe 하드 드라이브의 PSID(Physical Security ID) 되돌리기에 대한 액세스를 제어합니다.
표 12. 시스템 설정 옵션 - 시스템 관리 메뉴 (계속) 시스템 관리 기본적으로 이 옵션은 비활성화되어 있습니다. Wake on LAN Wake on LAN WLAN에서 절전 해제 신호를 받을 때 특수 LAN 신호에 의해 시스템이 켜지는 것을 활성화하거나 비활성화합니다. 기본적으로 Disabled(사용 안 함) 옵션이 선택되어 있습니다. Auto On Time 매일 또는 미리 선택한 날짜 및 시간에 시스템이 자동으로 켜지도록 설정할 수 있 습니다. 이 옵션은 Auto On Time(자동 켜짐 시간)이 매일, 평일 또는 선택한 요일에 설정된 경우에만 구성할 수 있습니다. 기본적으로 이 옵션은 비활성화되어 있습니다. Intel AMT Capability 인텔 AMT 기능 활성화 기본적으로 MEBx 액세스 제한 옵션은 활성화되어 있습니다. MEBx Hotkey MEBx 핫키 활성화 활성화 시 핫키를 사용하여 MEBx에 액세스할 수 있습니다.
표 14. 시스템 설정 옵션 - 사전 부팅 동작 메뉴 (계속) 사전 부팅 동작 USB-C Warnings 도킹 경고 메시지 활성화 이 옵션은 기본적으로 활성화되어 있습니다. Fastboot 부팅 프로세스의 속도를 설정합니다. 기본적으로 최소 옵션이 활성화되어 있습니다. Extend BIOS POST Time BIOS POST 시간을 설정합니다. 기본적으로 0초 옵션이 활성화되어 있습니다. MAC 주소 Pass-Through 외부 NIC MAC 주소를 시스템에서 선택한 MAC 주소로 교체합니다. 기본적으로 시스템 고유 MAC 주소 옵션이 활성화되어 있습니다. 마우스/터치패드 기본적으로 터치패드 및 PS/2 마우스 옵션은 활성화되어 있습니다. 표 15.
표 16. 시스템 설치 옵션—성능 메뉴 (계속) 성능 인텔 하이퍼 스레딩 기술 인텔 하이퍼 스레딩 기술 활성화 프로세서의 하이퍼 스레딩을 활성화 또는 비활성화합니다. 이 옵션은 기본적으로 활성화되어 있습니다. 동적 튜닝:머신 러닝 동적 튜닝 활성화:머신 러닝 탐지된 워크로드에 따라 동적 전원 튜닝 기능을 향상시키는 운영 체제 기능을 활성 화합니다. 기본적으로 이 옵션은 비활성화되어 있습니다. 표 17. 시스템 설치 옵션—시스템 로그 메뉴 시스템 로그 BIOS 이벤트 로그 BIOS 이벤트 로그 지우기 BIOS 이벤트를 표시합니다. 기본적으로 유지 옵션이 활성화되어 있습니다. 열 이벤트 로그 열 이벤트 로그 지우기 열 이벤트를 표시합니다. 기본적으로 유지 옵션이 활성화되어 있습니다. Power Event Log 전원 이벤트 로그 지우기 전원 이벤트를 표시합니다. 기본적으로 유지 옵션이 활성화되어 있습니다. 라이센스 정보 시스템의 라이선스 정보를 표시합니다.
8. BIOS 버전을 보려면 BIOS를 클릭합니다. 9. 최신 BIOS 파일을 찾고 다운로드를 클릭합니다. 10. 아래에서 선호하는 다운로드 방법을 선택하십시오 창에서 선호하는 다운로드 방법을 선택하고 파일 다운로드를 클릭합니다. 파일 다운로드 창이 나타납니다. 11. 파일을 바탕 컴퓨터에 저장하려면 Save(저장)를 클릭합니다. 12. Run(실행)를 클릭하여 업데이트 된 BIOS 설정을 컴퓨터에 설치합니다. 화면의 지시사항을 따르십시오. BitLocker가 활성화된 시스템에서 BIOS 업데이트 주의: BIOS를 업데이트하기 전에 BitLocker가 일시 중지되지 않으면 다음에 시스템을 재부팅 때 BitLocker 키가 인식되지 않습 니다. 이 경우 계속 진행하려면 복구 키를 입력하라는 메시지가 표시되며 시스템에서는 재부팅할 때마다 이 메시지를 표시합니 다. 복구 키를 모르는 경우 데이터가 손실되거나 운영 체제를 불필요하게 다시 설치해야 할 수 있습니다.
시스템 및 설정 암호 표 18. 시스템 및 설정 암호 암호 유형 설명 시스템 암호 시스템 로그온하기 위해 입력해야 하는 암호. 설정 암호 컴퓨터의 BIOS 설정에 액세스하고 변경하기 위해 입력해야 하는 암호. 컴퓨터 보안을 위해 시스템 및 설정 암호를 생성할 수 있습니다. 주의: 암호 기능은 컴퓨터 데이터에 기본적인 수준의 보안을 제공합니다. 주의: 컴퓨터가 잠겨 있지 않고 사용하지 않는 경우에는 컴퓨터에 저장된 데이터에 누구라도 액세스할 수 있습니다. 노트: 시스템 및 설정 암호 기능은 비활성화되어 있습니다. 시스템 설정 암호 할당 전제조건 설정 안 됨 상태일 때만 새 시스템 또는 관리자 암호를 할당할 수 있습니다. 이 작업 정보 시스템 설정에 들어가려면 전원이 켜진 직후 또는 재부팅 직후에 키를 누릅니다. 단계 1. 시스템 BIOS 또는 시스템 설정 화면에서 보안을 선택하고 키를 누릅니다. Security (보안) 화면이 표시됩니다. 2.
2. System Security(시스템 보안) 화면에서 Password Status(암호 상태)를 Unlocked(잠금 해제)합니다. 3. System Password를 선택하고, 기존 시스템 암호를 변경 또는 삭제한 후 키 또는 키를 누릅니다. 4. Setup Password를 선택하고, 기존 설정 암호를 변경 또는 삭제한 후 키 또는 키를 누릅니다. 노트: 시스템 및/또는 설정 암호를 변경하는 경우 프롬프트가 나타나면 새 암호를 다시 입력합니다. 시스템 및 설정 암호를 삭제하는 경우 프롬프트가 나타나면 삭제를 확인합니다. 5. 키를 누르면 변경 내용을 저장하라는 메시지가 표시됩니다. 6. 변경 내용을 저장하고 시스템 설정에서 나가려면 Y를 누릅니다. 컴퓨터가 다시 시작됩니다.
5 문제 해결 주제: • • • • • • • • • • • 운영 체제 복구 백업 미디어 및 복구 옵션 Dell SupportAssist 사전 부팅 시스템 성능 검사 진단 진단 LED 동작 실시간 클럭(RTC 재설정) BIOS 플래시(USB 키) BIOS 플래싱 Wi-Fi 전원 주기 BIOS recovery M-BIST LCD BIST(Built-in Self Test) 운영 체제 복구 컴퓨터가 반복 시도 후에도 운영 체제로 부팅할 수 없는 경우, Dell SupportAssist OS 복구를 자동으로 시작합니다. Dell SupportAssist OS 복구는 Windows 10 운영 체제와 함께 설치되는 모든 Dell 컴퓨터에 사전 설치되어 있는 독립 실행형 툴입니다. 컴퓨터가 운영 체제로 부팅하기 전에 발생할 수 있는 문제를 진단하고 해결할 수 있는 툴로 구성됩니다. 이 툴을 통해 하드웨어 문제 를 진단하거나, 컴퓨터를 수리하거나, 파일을 백업하거나, 출하 시 상태로 컴퓨터를 복원할 수 있습니다.
SupportAssist 사전 부팅 시스템 성능 검사 실행 단계 1. 컴퓨터를 켭니다. 2. 컴퓨터가 부팅될 때 Dell 로고가 나타나면 F12 키를 누릅니다. 3. 부팅 메뉴 화면에서 Diagnostics(진단) 옵션을 선택합니다. 4. 왼쪽 하단의 화살표를 클릭합니다. 진단 전면 페이지가 표시됩니다. 5. 오른쪽 하단 모서리의 화살표를 클릭하여 페이지 목록으로 이동합니다. 감지된 항목이 나열됩니다. 6. 특정 디바이스에서만 진단 테스트를 실행하려면 Esc를 누른 다음 Yes(예)를 눌러 진단 테스트를 중지합니다. 7. 왼쪽 창에서 장치를 선택하고 Run Tests(테스트 실행)을 클릭합니다. 8. 문제가 발생하면 오류 코드가 표시됩니다. 오류 코드와 검증 번호를 메모해둔 후 Dell에 문의하십시오. 진단 LED 동작 표 19. 진단 LED 동작 깜박임 패턴 주황색 흰색 문제 설명 권장 조치사항 1 1 TPM 탐지 장애 시스템 보드를 장착합니다.
표 19. 진단 LED 동작 (계속) 깜박임 패턴 주황색 흰색 문제 설명 권장 조치사항 2 7 LCD 장애(SBIOS 메시지) LCD 모듈을 교체합니다. 2 8 LCD 장애(전원 레일 장애의 EC 감지) 시스템 보드를 장착합니다. 3 1 CMOS 배터리 오류 ● ● CMOS 배터리 연결을 재설 정합니다, 문제가 지속되면 RTS 배터 리를 교체합니다. 3 2 PCI 또는 비디오 카드/칩 장애 3 3 BIOS 복구 이미지를 찾을 수 없 ● 음 ● 최신 BIOS 버전 플래시 문제가 지속되면 시스템 보 드를 교체합니다. 3 4 BIOS 복구 이미지를 찾았지만 유효하지 않음 최신 BIOS 버전 플래시 문제가 지속되면 시스템 보 드를 교체합니다. 3 5 전원 레일 장애 시스템 보드를 장착합니다. 3 6 SBIOS에서 감지한 플래시 손상 시스템 보드를 장착합니다. 3 7 ME에서 HECI 메시지에 대한 회 신을 기다리다 시간 초과되었 습니다.
BIOS 플래싱 이 작업 정보 사용 가능한 업데이트가 있거나 시스템 보드 교체 후 BIOS를 플래싱(업데이트)해야 할 수 있습니다. BIOS를 업데이트하려면 다음 단계를 따릅니다. 단계 1. 컴퓨터를 켭니다. 2. www.dell.com/support로 이동합니다. 3. 제품 지원을 클릭해 제품의 서비스 태그를 입력한 후 Submit(제출)을 클릭합니다. 노트: 서비스 태그가 없는 경우 수동으로 자동 검색 기능을 사용하여 컴퓨터 모델을 찾습니다. 4. Drivers & Downloads(드라이버 및 다운로드) > Find it myself(직접 찾기)를 클릭합니다. 5. 컴퓨터에 설치된 운영 체제를 선택합니다. 6. 페이지를 아래로 스크롤하여 BIOS를 확장할 수 있습니다. 7. Download(다운로드)을 클릭하여 컴퓨터 BIOS의 최신 버전을 다운로드합니다. 8. 다운로드가 완료된 후 BIOS 업데이트 파일을 저장한 폴더로 이동합니다. 9.
이전 버전은 이미 하드 드라이브에 저장되어 있습니다. BIOS는 하드 드라이브에 새 버전을 추가하고 이전 버전을 유지 관리하며 기타 기존 버전을 삭제합니다. 예를 들어 A00 및 A02 버전은 이미 하드 드라이브에 있으며 A02는 실행 중인 BIOS입니다. BIOS는 A04를 추 가하고 A02를 유지하며 A00을 삭제합니다. 두 가지 BIOS 버전을 사용하면 BIOS 롤백 기능을 사용할 수 있습니다. 복구 파일을 저장할 수 없는 경우(하드 드라이브 공간이 부족한 경우) BIOS는 이 상태를 나타내는 플래그를 설정합니다. 나중에 복구 파일을 저장할 수 있게 되는 경우 플래그가 재설정됩니다. POST 및 BIOS 설정 중에 BIOS가 사용자에게 알림을 표시하고 BIOS 복구가 저하됩니다. 하드 드라이브를 통한 BIOS 복구는 불가능하지만 USB 플래시 드라이브를 통한 BIOS 복구는 여전히 가능합니다. USB 키: 루트 디렉토리 또는 "\" BIOS_IMG.rcv: 복구 이미지가 USB 키에 저장됩니다.
USB 드라이브를 사용하여 BIOS 복구 이 작업 정보 노트: 운영 체제에 표시되는 파일 유형의 확장자인지 확인합니다. 노트: Dell 지원 사이트에서 최신 BIOS를 다운로드했는지 확인하고 시스템에 저장합니다. 단계 1. 다운로드한 BIOS 업데이트 실행(.exe) 파일의 위치를 찾습니다. 2. 파일 이름을 BIOS_IMG.rcv로 변경합니다. 예를 들어, 파일 이름이 PowerEdge_T30_0.0.5.exe이면 BIOS_IMG.rcv로 변경합니다. 3. BIOS_IMG.rcv 파일을 USB 키의 루트 디렉토리로 복사합니다. 4. 아직 연결하지 않은 경우 USB 드라이브를 연결하고 시스템을 재시작하고 F2 키를 눌러 System Setup으로 들어간 다음 전원 버튼 을 눌러 시스템을 종료합니다. 5. 시스템을 시작합니다. 6. 시스템 시작 중에 BIOS Recovery Menu 대화 상자가 표시될 때까지 전원 버튼을 누른 채로 Ctrl+Esc 키를 누릅니다. 7.
5. 화면에 여러 색상 막대가 표시되고 화면 전체가 빨간색, 초록색, 파란색으로 변합니다. 6. 화면을 자세히 살펴보며 이상이 없는지 확인합니다. 7. Esc 키를 눌러 종료합니다. 노트: Dell SupportAssist 사전 부팅 진단이 실행되면 사용자가 개입하여 LCD 기능을 확인할 것을 기다리며 LCD BIST를 먼저 시작 합니다.
6 도움말 보기 주제: • Dell에 문의하기 Dell에 문의하기 전제조건 노트: 인터넷에 연결되어 있지 않은 경우 구매 송장, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. 이 작업 정보 Dell은 다양한 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 단계 1. Dell.com/support로 이동합니다. 2. 지원 카테고리를 선택합니다. 3. 페이지 맨 아래에 있는 Choose a Country/Region(국가/지역 선택) 드롭다운 메뉴에서 국가 또는 지역을 확인합니다. 4. 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다.