Dell Latitude 7480 소유자 매뉴얼 규정 모델: P73G 규정 유형: P73G001 October 2020 개정 A04
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2017-2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자의 상표일 수 있습니다.
목차 장 1: 컴퓨터에서 작업하기................................................................................................................. 7 끄기 - Windows..................................................................................................................................................................... 7 컴퓨터 끄기 — Windows 8................................................................................................................................................. 7 컴퓨터 끄기 - Windows 7..............
LED 보드 분리............................................................................................................................................................... 23 LED 보드 설치............................................................................................................................................................... 24 스마트 카드 모듈...............................................................................................................................................................
Intel 소프트웨어 가드 확장 화면 옵션............................................................................................................................ 56 성능 화면 옵션....................................................................................................................................................................56 전원 관리 화면 옵션...........................................................................................................................................................
무선 화면 옵션....................................................................................................................................................................80 유지 보수 화면....................................................................................................................................................................80 시스템 로그............................................................................................................................................................
1 컴퓨터에서 작업하기 주제: • • • • • • 끄기 - Windows 컴퓨터 끄기 — Windows 8 컴퓨터 끄기 - Windows 7 컴퓨터 내부 작업을 시작하기 전에 안전 지침 컴퓨터 내부 작업을 마친 후에 끄기 - Windows 주의: 데이터 손실을 방지하기 위해, 컴퓨터를 끄기 전에 열린 파일을 모두 저장한 후 닫고 열린 프로그램을 모두 종료하거나 . 을 클릭 또는 탭합니다. 1. 2. 을 클릭 또는 탭한 다음, 종료를 클릭하거나 탭합니다. 노트: 컴퓨터 및 연결된 모든 디바이스의 전원이 꺼져 있는지 확인합니다. 운영 체제를 종료할 때 컴퓨터 및 연결된 디바이스 의 전원이 자동으로 꺼지지 않으면 전원 버튼을 6초 정도 눌러 끕니다. 컴퓨터 끄기 — Windows 8 주의: 데이터 손실을 방지하기 위해, 컴퓨터를 끄기 전에 열린 파일을 모두 저장한 후 닫고 열린 프로그램을 모두 종료하십시오. 1. 컴퓨터 전원 끄기: ● Windows 8(터치가 지원되는 장치): a.
컴퓨터 내부 작업을 시작하기 전에 1. 컴퓨터 덮개의 긁힘을 방지하기 위해 작업대 표면이 평평하고 깨끗한지 확인합니다. 2. 컴퓨터를 끕니다. 3. 컴퓨터가 도킹 장치에 연결되어 있으면(도킹된 상태) 도킹을 해제합니다. 4. 컴퓨터에서 모든 네트워크 케이블을 분리합니다(가능한 경우). 주의: 컴퓨터에 RJ45 포트가 있는 경우 먼저 컴퓨터에서 케이블을 뽑아 네트워크 케이블을 분리합니다. 5. 컴퓨터 및 모든 연결된 장치를 전원 콘센트에서 분리하십시오. 6. 디스플레이를 엽니다. 7. 수 초 동안 전원 버튼을 길게 눌러 시스템 보드를 접지합니다. 주의: 감전을 방지하려면 8번 단계를 수행하기 전에 컴퓨터를 전원 콘센트에서 분리합니다. 주의: 정전기 방전을 방지하려면 손목 접지대를 사용하거나 주기적으로 컴퓨터 뒷면의 커넥터와 도색되지 않은 금속 표면을 동시에 만져서 접지하십시오. 8. 설치된 Express 카드 또는 스마트 카드를 해당 슬롯에서 모두 분리합니다.
2. 컴퓨터에 전화선 또는 네트워크 케이블을 연결합니다. 주의: 네트워크 케이블을 연결하려면, 먼저 케이블을 네트워크 장치에 꽂은 다음 컴퓨터에 꽂습니다. 3. 전원 콘센트에 컴퓨터와 연결된 모든 장치를 연결합니다. 4. 컴퓨터를 켭니다.
2 분해 및 재조립 주제: • • • • • • • • • • • • • • • • • • • • • • • • • • 권장 도구 나사 크기 목록 가입자 식별 모듈 SIM 카드 베이스 덮개 배터리 PCIe 솔리드 스테이트 드라이브(SSD) 스피커 코인 셀 배터리 WWAN 카드 WLAN 카드 메모리 모듈 방열판 LED 보드 스마트 카드 모듈 터치패드 전원 커넥터 포트 디스플레이 어셈블리 터치 디스플레이 패널 디스플레이 베젤 비터치 디스플레이 패널 카메라 마이크 모듈 디스플레이 힌지 캡 더미 SIM 카드 트레이 분리 시스템 보드 키보드 격자 및 키보드 손목 보호대 권장 도구 본 설명서의 절차를 수행하는 데 다음 도구가 필요합니다. ● # 0 십자 드라이버 ● # 1 십자 드라이버 ● 소형 플라스틱 스크라이브 나사 크기 목록 표 1. Latitude 7480 - 나사 크기 목록 구성 요소 후면 덮개 M2.5x 6.0 M2.5x5.0 M2.0 x 5.
표 1. Latitude 7480 - 나사 크기 목록 (계속) 구성 요소 M2.5x 6.0 M2.5x5.0 M2.0 x 5.0 M2.5 x 4.0 M2.0x3.0 방열판 모듈 시스템 팬 M2.0 X 2.5 M2.0 X 2.0 4 2 2 WWAN 카드 1 WLAN 카드 1 전원 커넥터 포트 1 ESD 브래킷 EDP 브래킷 2 1 터치패드 버튼 2 지문 판독기 1 LED 보드 1 스마트 카드 판독기 케이지 2 디스플레이 힌지 6 디스플레이 패널 ● ● 키보드 지지판 FHD - 2 HD - 4 18 키보드 시스템 보드 5 3 가입자 식별 모듈 SIM 카드 SIM 카드 또는 SIM 카드 트레이 분리 노트: SIM 카드 또는 SIM 카드 트레이 분리는 WWAN 모듈과 함께 제공되는 시스템에서만 가능합니다. 따라서 분리 절차는 WWAN 모듈과 함께 제공되는 시스템에만 적용할 수 있습니다.
SIM 카드 장착 1. 2. 3. 4. 종이 클립 또는 SIM 카드 분리 도구를 SIM 카드 트레이의 핀홀에 삽입합니다. 스크라이브를 사용하여 SIM 카드 트레이를 잡아당깁니다. SIM 카드를 트레이에 놓습니다. SIM 카드 트레이를 슬롯에 삽입합니다. 더미 SIM 카드 트레이 분리 WWAN 카드와 함께 제공되는 모델의 경우 시스템 보드를 분리하기 전에 먼저 시스템에서 SIM 카드 트레이를 분리해야 합니다. 시스 템에서 SIM 카드 트레이를 분리하려면 분해 섹션에 설명된 단계를 따릅니다. 노트: 무선 카드만 함께 제공되는 모델의 경우 시스템 보드를 분리하기 전에 먼저 시스템에서 더미 SIM 카드 트레이를 분리해야 합니다. 더미 SIM 카드 트레이를 분리하는 단계는 다음과 같습니다. 1. SIM 카드 슬롯의 분리 래치를 안쪽으로 누릅니다. 2. 더미 SIM 카드 트레이를 시스템 밖으로 밉니다.
베이스 덮개 베이스 덮개 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 덮개를 분리하려면: a. 베이스 커버를 컴퓨터에 고정하는 8개의 M2.5 x 6 조임 나사를 풉니다[1]. 노트: 나사를 풀 때 주의하십시오. 나사 헤드가 손상되는 것을 방지하기 위해 나사 헤드의 앞 모서리와 일치하도록 드라이 버를 기울입니다. b. 플라스틱 스크라이브를 사용하여 가장자리에서 베이스 덮개를 분리한 후 컴퓨터에서 들어 올립니다[2]. 주의: 나사를 풀 때 주의하십시오. 나사 헤드가 손상되는 것을 방지하기 위해 나사 헤드(노트북 베이스 커버의 전면 모서리) 와 일치하도록 드라이버를 기울입니다. 3. 컴퓨터에서 베이스 덮개를 들어 올립니다.
베이스 커버 설치 1. 컴퓨터 가장자리에 있는 슬롯에 베이스 덮개 탭을 맞춥니다. 2. 딸깍 소리가 나면서 제자리에 고정될 때까지 덮개의 가장자리를 누릅니다. 3. M2.5 x 6.0 캡티브 나사를 조여 베이스 커버를 컴퓨터에 고정합니다. 노트: 나사를 조일 때 주의하십시오. 나사 헤드의 손상을 방지하기 위해 스크루 드라이버의 각도를 나사 헤드와 일치하도록 조정하십시오. 4. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 배터리 리튬 이온 배터리 예방 조치 주의: ● 리튬 이온 배터리를 다룰 때는 주의하십시오. ● 배터리를 제거하기 전에 완전히 방전시키십시오. 시스템에서 AC 전원 어댑터의 연결을 해제하고 배터리 전원으로만 컴퓨터 를 작동시킵니다. 전원 버튼을 눌렀을 때 컴퓨터가 더 이상 켜지지 않으면 배터리가 완전히 방전된 것입니다. ● 배터리를 찌그러뜨리거나 떨어뜨리거나 훼손하거나 외부 개체로 배터리에 구멍을 뚫지 마십시오. ● 고온에 배터리를 노출하거나 배터리 팩과 셀을 분해하지 마십시오.
● 배터리가 부풀어 컴퓨터에서 분리되지 않을 경우, 위험할 수 있으니 리튬 이온 배터리에 구멍을 뚫거나 배터리를 구부리거나 찌그러뜨려 분리하려고 하지 마십시오. 이러한 경우 Dell 기술 지원에 문의하여 지원을 받으십시오. www.dell.com/ contactdell을 참조하십시오. ● 항상 www.dell.com 또는 공인 Dell 파트너 및 리셀러로부터 정품 배터리를 구입하십시오. 배터리 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 덮개를 분리합니다. 3. 배터리를 분리하려면: a. 시스템 보드의 커넥터에서 배터리 케이블을 분리합니다[1]. b. 배터리를 컴퓨터에 고정시키는 M2.0 x 5.0 나사를 분리합니다[2]. 노트: 3셀 배터리에는 나사 1개, 4셀 배터리에는 나사 2개가 있습니다. 그러므로 아래에 표시된 그림은 4셀 배터리입니다. c. 컴퓨터에서 배터리를 들어 올립니다[3]. 배터리 설치 1. 배터리를 컴퓨터의 슬롯에 삽입합니다. 2.
5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. PCIe 솔리드 스테이트 드라이브(SSD) PCIe SSD 제거 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 를 제거합니다.. 3. 시스템 보드의 커넥터에서 배터리 케이블을 연결 해제합니다. 4. PCIe SSD를 분리하려면: a. SSD 브래킷을 고정하는 M2 x3 캡티브 나사를 풉니다[1]. b. SSD 브래킷을 분리합니다[2]. c. 시스템 보드의 커넥터에서 PCIe SSD를 제거합니다[3]. PCIe SSD 설치 1. PCIe SSD 카드를 커넥터에 삽입합니다. 2. PCIe SSD 카드 위에 SSD 브래킷을 설치합니다. 노트: SSD 브래킷을 설치할 때 브래킷의 탭이 손목 받침대의 탭에 단단하게 고정되어 있는지 확인합니다. 노트: 시스템에 브래킷이 함께 제공된 경우 브래킷을 설치해야 합니다.
3. M2 x 3 나사를 조여 SSD 브래킷에 고정합니다. 4. 배터리 케이블을 시스템 보드의 커넥터에 연결합니다. 5. 베이스 덮개를 설치합니다. 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 스피커 스피커 모듈 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a. 베이스 덮개 b. 배터리 3. 스피커 모듈을 분리하려면: a. 시스템 보드의 커넥터에서 스피커 케이블을 밀어서 연결 해제합니다[1]. 노트: 라우팅 클립에서 스피커 케이블을 분리해야 합니다. 노트: 플라스틱 스크라이브를 사용하여 케이블을 해당 커넥터에서 분리합니다. 케이블이 파손될 수 있으므로 당기지 마 십시오. b. 라우팅 클립에서 스피커 케이블을 라우팅 해제합니다[2]. c. 스피커 케이블을 터치패드 보드에 고정하는 테이프를 제거합니다[3]. 4. 스피커 모듈을 제거하려면: a. 스피커 모듈을 컴퓨터에 고정하는 4개의 M2.0X3.0 나사를 분리합니다[1]. b.
노트: 라우팅 클립에서 스피커 케이블을 분리해야 합니다. 스피커 모듈 설치 1. 스피커 모듈을 컴퓨터의 슬롯에 끼웁니다. 2. 컴퓨터의 고정 클립을 통해 스피커 케이블을 배선합니다. 3. 스피커 케이블을 시스템 보드의 커넥터에 연결합니다. 4. 다음을 설치합니다: a. 배터리 b. 베이스 덮개 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 코인 셀 배터리 코인 셀 배터리 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 를 제거합니다. a. 베이스 커버 3. 배터리를 연결 해제합니다. 4. 코인 셀 배터리를 분리하려면: a. 시스템 보드의 커넥터에서 코인 셀 배터리 케이블을 분리합니다[1]. b. 코인 셀 배터리를 들어 올려 부착면에서 분리합니다[2].
코인 셀 배터리 설치 1. 코인 셀 배터리를 컴퓨터 내부의 슬롯에 부착합니다. 2. 케이블을 연결하기 전에 코인 셀 배터리 케이블을 라우팅 채널에 통과시켜 라우팅합니다. 3. 코인 셀 배터리 케이블을 시스템 보드의 커넥터에 연결합니다. 4. 배터리를 다시 연결합니다. 5. 를 설치합니다. a. 베이스 커버 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. WWAN 카드 WWAN 카드 제거 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버. 3. 시스템 보드의 커넥터에서 배터리 케이블을 연결 해제합니다. 4. WWAN 카드를 분리하려면: a. 금속 브래킷을 WWAN 카드에 고정하는 M2.0X3.0 나사를 제거합니다. b. WWAN 카드를 고정하는 금속 브래킷을 들어 올립니다. c. 플라스틱 스크라이브로 WWAN 케이블을 WWAN 카드의 커넥터에서 분리합니다. d. .
WWAN 카드 설치 1. WWAN 카드를 시스템 보드의 커넥터에 끼웁니다. 2. WWAN 케이블을 WWAN 카드의 커넥터에 연결합니다. 3. 금속 브래킷을 놓고 M2.0 x 3.0 나사를 조여 컴퓨터에 고정합니다. 4. 배터리 케이블을 시스템 보드의 커넥터에 연결합니다. 5. 베이스 커버. 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 노트: WWAN 카드에서는 IMEI 번호도 확인할 수 있습니다. WLAN 카드 WLAN 카드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버. 3. 시스템 보드의 커넥터에서 배터리 케이블을 연결 해제합니다. 4. WLAN 카드를 분리하려면: a. b. c. d. 20 금속 브래킷을 WLAN 카드에 고정시키는 M2.0 x 3.0 나사를 제거합니다[1]. 금속 브래킷을 들어 올립니다[2]. WLAN 케이블을 WLAN 카드의 커넥터에서 분리합니다[3]. 컴퓨터에서 WLAN 카드를 제거합니다[4].
노트: 핀의 손상을 방지하려면 WLAN 카드를 35°가 넘는 각도로 당기지 마십시오. WLAN 카드 설치 1. WLAN 카드를 시스템 보드의 커넥터에 끼웁니다. 2. WLAN 케이블을 WLAN 카드의 커넥터에 연결합니다. 3. 금속 브래킷을 놓고 M2.0 x 3.0 나사를 조여 컴퓨터에 고정합니다. 4. 배터리 케이블을 시스템 보드의 커넥터에 연결합니다. 5. 를 설치합니다.베이스 커버. 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 메모리 모듈 메모리 모듈 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 베이스 커버. 3. 시스템 보드의 커넥터에서 배터리 케이블을 연결 해제합니다. 4. 메모리 모듈을 분리하려면: a. 모듈이 튀어나올 때까지 메모리 모듈을 고정하는 클립을 잡아당깁니다[1]. b. 시스템 보드의 커넥터에서 메모리 모듈을 제거합니다[2].
메모리 모듈 설치 1. 메모리 모듈이 제자리에 끼워질 때까지 커넥터에 삽입합니다. 2. 배터리 케이블을 시스템 보드의 커넥터에 연결합니다. 3. 베이스 커버. 4. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 방열판 방열판 조립품 분리 방열판 조립품은 방열판 및 시스템 팬으로 구성됩니다. 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다. a. 베이스 덮개 b. 배터리 3. 방열판 조립품을 분리하려면: 노트: 나사 개수를 식별하려면 나사 목록을 참조하십시오. a. 시스템 보드에서 팬 케이블을 분리합니다[1]. 노트: 방열판 어셈블리를 제거한 후 팬 케이블을 연결 해제했는지 확인합니다. b. 방열판 어셈블리를 시스템 보드에 고정시키는 M2.0 x 5.0 나사를 제거합니다[2].
노트: 방열판에 표시된 설명선 번호[1, 2, 3, 4] 순서로 나사를 제거합니다 . c. 시스템 보드에서 방열판 조립품을 들어 올립니다[3]. 방열판 조립품 장착 방열판 조립품은 방열판 및 시스템 팬으로 구성됩니다. 1. 방열판 어셈블리를 시스템 보드의 나사 홀더에 맞추고 . 2. M2.0 x 3.0 나사를 조여 방열판 조립품을 시스템 보드에 고정시킵니다. 노트: 방열판에 표시된 대로 설명선 번호[1, 2, 3, 4]의 순서로 나사를 조입니다 . 3. 시스템 보드의 커넥터에 팬 케이블을 연결합니다. 4. 다음을 설치합니다. a. 배터리 b. 베이스 덮개 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. LED 보드 LED 보드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다. a. 베이스 덮개 b. 배터리 3.
a. LED 보드에서 LED 케이블을 분리합니다[1]. 주의: 케이블 커넥터가 파손될 수 있으므로 케이블을 당기지 않도록 합니다. 대신, 스크라이브를 사용하여 케이블 커넥터 의 가장자리를 밀어 LED 케이블을 분리합니다. b. LED 보드를 컴퓨터에 고정시키는 M2.0 x 3.0 나사를 제거합니다[2]. c. LED 보드를 컴퓨터에서 들어 올립니다[3]. LED 보드 설치 1. LED 보드를 컴퓨터의 슬롯에 삽입합니다. 2. M2.0 x 3.0나사를 조여 LED 보드를 고정합니다. 3. LED 케이블을 시스템 보드에 연결합니다. 4. 다음을 설치합니다. a. 배터리 b. 베이스 덮개 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 스마트 카드 모듈 스마트 카드 케이지 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a. 베이스 덮개 b.
c. PCIe SSD 카드 3. 스마트 카드 케이블을 분리하려면: a. 스마트 카드 케이블을 분리합니다[1]. 노트: 스마트 카드 헤드가 손상되지 않도록 커넥터를 조심스럽게 밀어야 합니다. b. 터치패드 모듈에 부착되어 있는 스마트 케이블 카드를 들어 올립니다[2]. 노트: 접착 테이프로 조심스럽게 당겨서 분리합니다. 4. 스마트 카드 케이지를 분리하려면: 노트: 나사 개수를 식별하려면 나사 목록을 참조하십시오. a. 스마트 카드 케이지를 컴퓨터에 고정시키는 2개의 M2 x 3 나사를 제거합니다[1]. b. 스마트 카드 케이지를 컴퓨터에서 밀어서 들어 올립니다[2].
스마트 카드 케이지 설치 1. 스마트 카드 케이지를 슬롯에 밀어 넣어 컴퓨터의 탭에 맞춥니다. 2. M2 x 3 나사를 조여 스마트 카드 케이지를 컴퓨터에 고정시킵니다. 3. 스마트 카드 케이블을 부착한 후 이를 컴퓨터의 커넥터에 연결합니다. 4. 다음을 설치합니다: a. PCIe SSD 카드 b. 배터리 c. 베이스 덮개 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 터치패드 터치패드 버튼 보드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a. 베이스 덮개 b. 배터리 c. 스피커 3. 스마트 카드 케이블을 분리하려면: a. 스마트 카드 케이블을 분리합니다[1].
b. 컴퓨터[2]에 부착되어 있는 스마트 카드 케이블을 들어 올려 터치패드 버튼 보드 케이블을 표시합니다. c. 스피커 케이블을 터치패드 패널에 고정시키는 접착 테이프를 떼어냅니다[3]. 노트: 라우팅 클립을 통해 터치패드 버튼에서 스피커 케이블을 라우팅 해제합니다. 4. 터치패드 버튼 보드를 분리하려면: a. 터치패드 버튼 보드 케이블을 터치패드 보드에서 분리합니다[1]. 노트: 터치패드 버튼 보드 케이블은 스마트 카드 케이블 아래에 있습니다. 래치를 들어 올려 터치패드 버튼 보드 케이블을 분리해야 합니다. b. 터치패드 버튼 보드를 고정하는 2개의 M2.0X3.0 나사를 분리합니다[2]. 노트: 나사를 식별하려면 나사 목록을 참조하십시오. c. 터치패드 버튼 보드를 컴퓨터에서 들어 올립니다[3].
터치패드 버튼 보드 설치 1. 터치패드 버튼 보드를 슬롯에 삽입하여 탭을 컴퓨터의 홈에 맞춥니다. 2. M2.0 x 3.0 나사를 조여 터치패드 버튼 보드를 컴퓨터에 고정시킵니다. 3. 터치패드 버튼 보드 케이블을 터치패드 보드의 커넥터에 연결합니다. 4. 스마트 카드 케이블을 부착한 후 이를 컴퓨터의 커넥터에 연결합니다. 5. 다음을 설치합니다: a. 스피커 b. 배터리 c. 베이스 덮개 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 전원 커넥터 포트 전원 커넥터 포트 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 를 분리합니다. a. 베이스 덮개 b. 배터리 3. 전원 커넥터 포트를 분리하려면: a. 시스템 보드에서 전원 커넥터 포트 케이블을 분리합니다[1]. 노트: 커넥터를 덮고 있는 접착 테이프를 떼어내야 합니다.
노트: 플라스틱 스크라이브를 사용하여 케이블을 해당 커넥터에서 분리합니다. 파손될 수 있으므로 케이블을 당기지 마 십시오. b. 1개의 M2.0X3.0 나사를 분리하여 전원 커넥터 포트의 금속 브래킷을 분리합니다[2]. c. 금속 브래킷을 컴퓨터에서 들어 올립니다[3]. d. 컴퓨터에서 전원 커넥터 포트를 [4]. 전원 커넥터 포트 설치 1. 전원 커넥터 포트를 컴퓨터의 슬롯에 설치합니다. 2. 금속 브래킷을 전원 커넥터 포트 위에 놓습니다. 3. M2.0x3.0 나사를 조여 전원 커넥터 포트를 컴퓨터에 고정시킵니다. 4. 시스템 보드의 커넥터에 전원 커넥터 포트 케이블을 연결합니다. 5. 를 설치합니다. a. 배터리 b. 베이스 덮개 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 어셈블리 디스플레이 어셈블리 제거 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a.
b. 배터리 c. WLAN 카드 d. WWAN 카드 노트: 나사 개수를 식별하려면 나사 목록을 참조하십시오. 3. 디스플레이 어셈블리를 제거하려면 다음을 수행합니다. a. b. c. d. e. f. 라우팅 채널에서 WLAN 케이블과 WWAN 케이블을 분리합니다[1]. IR 카메라 케이블을 시스템 보드에서 연결 해제합니다[2]. eDP 브래킷을 고정하는 M2.0x3.0 나사를 제거합니다[3]. eDP 브래킷을 eDP 케이블에서 들어 올립니다[4]. eDP 케이블을 들어 올려 시스템 보드의 커넥터에서 연결 해제합니다[5]. eDP 케이블을 라우팅 채널에서 라우팅 해제합니다[6]. 4. 디스플레이 어셈블리를 제거하려면 다음을 수행합니다. a. 컴퓨터의 디스플레이를 180도로 열어 평평한 표면에 눕혀 놓습니다. b. 디스플레이 힌지를 디스플레이 어셈블리에 고정하는 M2.5 x 4.0 나사를 제거합니다[1]. c. 디스플레이 어셈블리를 컴퓨터에서 들어 올립니다.
디스플레이 어셈블리 설치 1. 컴퓨터의 베이스를 테이블 표면에 놓고 테이블 가장자리 가까이에 배치합니다. 2. 디스플레이 어셈블리를 설치하고 시스템의 디스플레이 힌지 홀더에 맞춥니다. 3. 디스플레이 어셈블리를 잡고 M2.5 x 4.0 나사를 조여 시스템 디스플레이 어셈블리의 디스플레이 힌지를 시스템 유닛에 고정합니 다. 4. 테이프를 부착하여 eDP 케이블(디스플레이 케이블)을 고정합니다. 5. eDP 케이블을 시스템 보드의 커넥터에 연결합니다. 6. eDP 금속 브래킷을 eDP 케이블에 설치하고 M2.0x3.0 나사를 조입니다. 7. IR 카메라 케이블을 시스템 보드에 연결합니다. 8. WLAN 및 WWAN 케이블을 라우팅 채널을 통해 라우팅합니다. 9. 다음을 설치합니다. a. b. c. d. WLAN 카드 WWAN 카드 배터리 베이스 커버 10. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
c. WLAN 카드 d. WWAN 카드 e. 디스플레이 어셈블리 3. 터치 디스플레이 패널을 분리하려면: a. 플라스틱 스크라이브를 사용하여 디스플레이 패널의 가장자리를 풉니다. b. c. d. e. 32 상단에서 디스플레이 화면을 뒤집으십시오. 접착 테이프[1], 마일라 실드[2]를 떼어냅니다. 래치[3]에서 손을 떼고 eDP 케이블[4]을 연결 해제합니다. 접착 테이프를 떼어 내고[5] IR 케이블을 연결 해제합니다[6].
4. 디스플레이 조립품에서 디스플레이 베젤을 분리합니다. 터치 디스플레이 패널 설치 노트: 터치 디스플레이 패널 설치 절차는 터치 디스플레이 구성이 있는 시스템에만 적용됩니다. 1. 디스플레이 패널을 디스플레이 어셈블리에 놓습니다. 2. IR 케이블과 eDP 케이블을 다시 연결합니다. 3. 접착 테이프와 마일라 실드를 교체하십시오. 4. 디스플레이 모서리를 눌러 디스플레이 어셈블리 안으로 딸깍 소리가 날 때까지 누릅니다. 5. 다음을 설치합니다. a. b. c. d. e. 디스플레이 어셈블리 WLAN 카드 WWAN 카드 배터리 베이스 커버 6. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 디스플레이 베젤 디스플레이 베젤(비터치) 제거 노트: 디스플레이 베젤 제거 절차는 비터치 디스플레이 구성에만 적용됩니다.
1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a. b. c. d. e. 베이스 커버 배터리 WLAN 카드 WWAN 카드 디스플레이 어셈블리 3. 디스플레이 베젤을 제거하려면: a. 플라스틱 스크라이브를 사용하여 디스플레이의 하단 가장자리를 풉니다[1]. b. 디스플레이 가장자리의 탭을 풉니다[2]. 노트: 접착제는 디스플레이 베젤을 디스플레이 패널에 고정하는 데 사용합니다. 4. 디스플레이 조립품에서 디스플레이 베젤을 분리합니다. 디스플레이 베젤(비터치) 설치 노트: 디스플레이 베젤 설치 절차는 비터치 디스플레이 구성에만 적용됩니다. 1. 디스플레이 베젤을 디스플레이 어셈블리에 놓습니다. 2. 디스플레이 조립품에 끼워질 때까지 디스플레이 베젤의 모서리를 누릅니다. 노트: 접착제는 디스플레이 베젤을 디스플레이 패널에 고정하는 데 사용합니다. 3. 다음을 설치합니다. a. b. c. d. e.
비터치 디스플레이 패널 디스플레이 패널 제거(비터치) 노트: 디스플레이 패널 제거 절차는 비터치 디스플레이 구성에만 적용됩니다. 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음 구성부품을 분리합니다. a. b. c. d. e. f. g. 베이스 커버 배터리 WLAN 카드 WWAN 카드 디스플레이 어셈블리 디스플레이 베젤 힌지 캡 3. 디스플레이 패널을 분리하려면: a. 패널에서 2개의 (M2.0 x 2.0) 나사를 제거합니다[1]. b. 디스플레이 패널의 하단 가장자리를 들어 올립니다[2]. c. 디스플레이 패널을 아래쪽에서 시스템에서 밀어 내고[1] 디스플레이 패널을 뒤집습니다[2].
d. 디스플레이 패널에서 디스플레이 커넥터 접착 스트립을 떼어냅니다[1]. e. 디스플레이 케이블을 디스플레이 패널 후면에 고정하는 마일라 테이프를 떼어냅니다[2]. f. 금속 탭을 들어 올리고 디스플레이 패널 뒷면에서 디스플레이 케이블을 분리합니다[3,4]. g. 디스플레이 패널을 분리합니다. 디스플레이 패널 힌지 설치(비터치) 노트: 디스플레이 패널 설치 절차는 비터치 디스플레이 구성에만 적용됩니다.
1. 디스플레이 패널 뒷면의 디스플레이 케이블을 연결합니다. 2. 디스플레이 패널 뒷면에 디스플레이 케이블을 고정하는 마일라 테이프를 부착합니다. 3. 디스플레이 커넥터 접착 스트립을 디스플레이 패널에 부착합니다. 4. 디스플레이 패널을 뒤집고 디스플레이 패널을 시스템쪽으로 밉니다. 5. 패널에서 2개의 (M2.0 x 2.0) 나사를 장착합니다. 6. 다음을 설치합니다. a. b. c. d. e. f. g. 베젤 힌지 캡 디스플레이 어셈블리 WLAN 카드 WWAN 카드 배터리 베이스 커버 7. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 카메라 마이크 모듈 카메라 마이크 모듈 제거 마이크 카메라 모듈의 제거 절차는 비터치 디스플레이 구성에만 해당됩니다. 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음을 제거합니다: a. b. c. d. e. f. g. 베이스 커버 WLAN 카드 WWAN 카드 배터리 디스플레이 어셈블리 디스플레이 베젤 디스플레이 힌지 3.
카메라 설치 설치 절차는 비터치 디스플레이 구성으로 배송되는 시스템에만 적용됩니다. 1. 카메라 케이블을 연결합니다. 2. 카메라 마이크 모듈을 디스플레이 어셈블리의 슬롯에 삽입합니다. 3. 테이프를 부착하여 카메라 모듈을 고정합니다. 4. 다음을 설치합니다. a. b. c. d. e. f. g. h. 디스플레이 베젤 디스플레이 어셈블리 디스플레이 힌지 디스플레이 패널 WLAN 카드 WWAN 카드 배터리 베이스 커버 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 노트: 카메라 모듈을 교체할 때 두 개의 전도성 테이프 조각을 제거한 다음 다시 부착해야 합니다.
디스플레이 힌지 캡 디스플레이 힌지 캡 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 다음 구성부품을 분리합니다. a. b. c. d. e. 베이스 커버 배터리 WLAN 카드 WWAN 카드 디스플레이 어셈블리 3. 힌지 캡을 왼쪽에서 오른쪽으로 밀어 디스플레이 패널에서 디스플레이 힌지 캡을 분리합니다. 디스플레이 힌지 캡 설치 1. 디스플레이 힌지 캡을 슬롯에 놓고 다시 밀어 디스플레이 어셈블리에 맞 춥니다. 2. 다음을 설치합니다. a. b. c. d. e. 디스플레이 어셈블리 WLAN 카드 WWAN 카드 배터리 베이스 커버 3. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 더미 SIM 카드 트레이 분리 WWAN 카드와 함께 제공되는 모델의 경우 시스템 보드를 분리하기 전에 먼저 시스템에서 SIM 카드 트레이를 분리해야 합니다. 시스 템에서 SIM 카드 트레이를 분리하려면 현장 서비스 설명서의 분해 섹션에 설명된 단계를 따릅니다.
의 경우 시스템 보드를 분리하기 전에 먼저 시스템에서 더미 SIM 카드 트레이를 분리해야 합니다. 더미 SIM 카드 트레이를 분리하는 단계는 다음과 같습니다. 1. SIM 카드 슬롯에 있는 분리 래치를 안쪽으로 누릅니다. 2. 더미 SIM 카드 트레이를 시스템 밖으로 밉니다. 시스템 보드 시스템 보드 분리 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. If your computer is shipped with a WWAN card, then the removal of a blank SIM card tray is a requirement. 2. 다음을 제거합니다: a. b. c. d. e. f. g. h. i. SIM 카드 더미 SIM 카드 트레이 베이스 덮개 배터리 메모리 모듈 PCIe SSD WLAN 카드 WWAN 카드 방열판 조립품 To identify the screws, seescrew list 3. 시스템 보드에 메모리 모듈 브래킷을 고정시키는 M2.0 x 3.
4. eDP 케이블을 분리하려면: a. b. c. d. e. f. 라우팅 채널에서 WLAN 케이블과 WWAN 케이블을 분리합니다[1]. 시스템 보드에서 IR 케이블을 분리합니다[2]. eDP 케이블을 고정시키는 M2.0 x 3.0 나사를 제거합니다[3]. eDP 케이블 브래킷을 분리합니다[4]. eDP 케이블을 시스템 보드에서 분리합니다[5]. 라우팅 클립에서 eDP 케이블을 분리합니다[6].
5. 케이블을 분리하려면: 노트: 스피커, LED 보드, 코인 셀 배터리 및 전원 커넥터 포트 케이블을 분리하려면 플라스틱 스크라이브를 사용하여 커넥터 에서 케이블을 분리합니다. 파손될 수 있으므로 케이블을 당기지 마십시오. a. b. c. d. e.
6. 시스템 보드를 분리하려면: a. USB Type-C 브래킷을 분리합니다. 그림에서는 USB Type-C 브래킷 분리를 표시하지 않습니다. b. 시스템 보드를 고정시키는 M2.0 x 5.0 나사를 분리합니다[1]. c. 시스템 보드를 들어 올려 컴퓨터에서 분리합니다.
7. USB Type-C 브래킷을 고정시키는 M2.0x5.0 나사를 분리합니다. 8. 시스템 보드를 뒤집고 브래킷을 고정시키는 테이프를 떼어내고 시스템 보드에서 USB Type-C 포트를 제거합니다.
시스템 보드 설치 1. USB Type-C 포트를 브래킷과 함께 시스템 보드의 슬롯에 놓습니다. 2. 테이프를 붙여 Type-C 브래킷을 고정시킵니다. 3. 시스템 보드를 뒤집고 M2 x 3 나사를 조여 USB Type-C 포트를 시스템 보드에 고정합니다. 4. 시스템 보드를 컴퓨터의 나사 홀더에 맞춥니다. 5. 시스템 보드를 컴퓨터에 고정시키는 M2 x 3 나사를 조입니다. 6. 스피커, 전원 커넥터, LED 보드, 터치패드, USH 케이블을 시스템 보드의 커넥터에 연결합니다. 7. eDP 케이블을 시스템 보드의 커넥터에 연결합니다. 8. 금속 브래킷을 eDP 케이블 위에 놓고 M2.0 x 5.0 나사를 조여 고정합니다. 9. 제거한 시스템 보드의 메모리 모듈 커넥터에서 금속 브래킷을 제거합니다. 10. 금속 브래킷을 메모리 모듈 커넥터 위에 놓고 M2 x 3 나사를 조여 컴퓨터에 고정시킵니다. 노트: 컴퓨터에 WWAN 카드가 있는 경우 다음 SIM 카드 트레이를 설치해야 합니다. 11.
c. d. e. f. g. h. 메모리 모듈 PCIe SSD WLAN 카드 WWAN 카드 방열판 조립품 시스템 보드 3. 손목 받침대 끝에서 케이블을 분리합니다. a. 키보드 케이블[1] b. 키보드 백라이트 케이블[2] c. 터치패드 및 USH 보드 케이블[3, 4] 4. 키보드 조립품을 분리하려면: 노트: 나사를 식별하려면 나사 목록을 참조하십시오. a. 키보드를 고정시키는 M2.0 x 2.5 나사를 분리합니다[1]. b. 키보드 조립품을 섀시에서 들어 올립니다[2].
키보드 트레이에서 키보드 제거 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2. 키보드 어셈블리를 제거합니다. 3. 키보드를 키보드 어셈블리에 고정하는 5개의 M2.0 x 2.0 나사를 제거합니다. 4. 키보드를 들어 올려 키보드 트레이에서 분리합니다. 키보드 트레이에 키보드 설치 1. 키보드 트레이의 나사 홀더에 키보드를 맞춥니다.
2. 5개의 M2.0 x 2.0 나사를 조여서 키보드를 키보드 트레이에 고정합니다. 3. 키보드 어셈블리를 설치합니다. 키보드 조립품 설치 노트: 키보드 및 키보드 트레이를 함께 키보드 조립품이라고 합니다. 노트: 키보드의 격자 측면에는 여러 개의 스냅 지점이 있으며 교체 키보드에 이를 고정하여 맞추기 위해서는 스냅 지점을 세게 눌 러야 합니다. 1. 키보드 조립품을 컴퓨터의 나사 홀더에 맞춥니다. 2. 키보드를 섀시에 고정하는 M2.0 x 2.5 나사를 조입니다. 3. 키보드 케이블, 키보드 백라이트 케이블 및 터치패드 케이블 케이블을 터치패드 버튼 보드의 커넥터에 연결합니다. 4. 다음을 설치합니다: a. b. c. d. e. f. g. h. 시스템 보드 방열판 WLAN 카드 WWAN 카드 SSD 카드 메모리 모듈 배터리 베이스 덮개 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다. 손목 보호대 팜레스트 장착 1. 컴퓨터 내부 작업을 시작하기 전에의 절차를 따릅니다. 2.
i. j. k. l. m. 코인 셀 배터리 스피커 디스플레이 어셈블리 시스템 보드 키보드 남은 구성 요소는 손목 받침대입니다. 3. 손목 받침대를 장착합니다. 4. 다음을 설치합니다. a. b. c. d. e. f. g. h. i. j. k. l. m. 키보드 시스템 보드 디스플레이 어셈블리 스피커 코인 셀 배터리 방열판 전원 커넥터 포트 WLAN 카드 WWAN 카드 PCIe SSD 메모리 배터리 베이스 커버 5. 컴퓨터 내부 작업을 마친 후에의 절차를 따릅니다.
3 시스템 설치 주제: • • • • • • • • • • • • • • • • • • • • 부팅 메뉴 탐색 키 시스템 설치 옵션 일반 화면 옵션 시스템 구성 화면 옵션 비디오 보안 화면 옵션 보안 부팅 화면 옵션 Intel 소프트웨어 가드 확장 화면 옵션 성능 화면 옵션 전원 관리 화면 옵션 POST Behavior(POST 동작) 화면 옵션 관리 기능 가상화 지원 화면 옵션 무선 화면 옵션 유지 보수 화면 시스템 로그 Windows에서 BIOS 업데이트 USB 플래시 드라이브를 사용하는 BIOS 업데이트 시스템 및 설정 암호 부팅 메뉴 시스템에 유효한 부팅 장치 목록이 포함된 원타임 부팅 메뉴를 시작하려면 Dell™ 로고가 나타날 때 키를 누릅니다. 진단 및 BIOS 설정 옵션도 이 메뉴에 포함되어 있습니다. 부팅 메뉴에 나열된 장치들은 시스템의 부팅 가능한 장치에 따라 다릅니다. 이 메뉴 는 특정 장치에 부팅을 시도하거나, 시스템 진단을 할 때 유용합니다.
키 탐색기 위쪽 화살표 이전 필드로 이동합니다. 아래쪽 화살표 다음 필드로 이동합니다. Enter 선택한 필드에서 값을 선택하거나(해당하는 경우) 필드의 링크로 이동합니다. 스페이스바 드롭다운 목록(있는 경우)을 확장하거나 축소합니다. 탭 다음 작업 영역으로 이동합니다. Esc 기본 화면이 보일 때까지 이전 페이지로 이동합니다. 기본 화면에서 Esc 키를 누르면 저장하지 않은 변경 사항 을 저장하고 시스템을 다시 시작하라는 메시지가 표시됩니다. 시스템 설치 옵션 노트: 노트북 컴퓨터 및 장착된 디바이스에 따라 이 섹션에 나열된 항목이 표시되거나 표시되지 않을 수 있습니다. 일반 화면 옵션 이 섹션에는 컴퓨터의 기본 하드웨어 기능이 나열됩니다. 옵션 설명 System information 이 섹션에는 컴퓨터의 기본 하드웨어 기능이 나열됩니다. Battery Information 배터리 수명 및 AC 어댑터가 설치되어 있는지 여부를 표시합니다.
시스템 구성 화면 옵션 옵션 설명 Integrated NIC 내장형 네트워크 컨트롤러를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● Parallel Port 도킹 스테이션의 병렬 포트를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● Serial Port 비활성화됨. AT: 이 옵션은 기본적으로 활성화됩니다. PS2 ECP 내장형 직렬 포트를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● ● SATA Operation 비활성화됨. 활성 상태 Enable UEFI network stack(UEFI 네트워크 스택 활성화): 이 옵션은 기본적으로 활성화되어 있습니다. Enabled w/PXE(PXE와 함께 사용) 비활성화됨. COM1: 이 옵션은 기본적으로 활성화됩니다. COM2 COM3 COM4 내부 SATA 하드 드라이브 컨트롤러를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● 비활성화됨.
옵션 설명 노트: USB 키보드와 마우스는 이러한 설정에 관계 없이 항상 BIOS 설정에서 작동합니다. USB PowerShare 이 필드는 USB PowerShare 기능의 동작을 구성합니다. 이 옵션으로 USB PowerShare 포트를 통해 저장된 시 스템 배터리 전력을 사용하여 외부 장치를 충전할 수 있습니다. 이 옵션은 기본적으로 비활성화되어 있습니 다. 오디오 이 필드는 내장형 오디오 컨트롤러를 활성화 또는 비활성화합니다. Enable Audio(오디오 사용) 옵션은 기본 적으로 선택되어 있습니다. 옵션은 다음과 같습니다. ● 마이크로폰 활성화(기본적으로 활성화) ● Enable Internal Speaker(내부 스피커 활성화) — 기본적으로 활성화 Keyboard Illumination 이 필드에서는 키보드 조명 기능의 작동 모드를 선택할 수 있습니다. 키보드 밝기 레벨은 0%에서 100%까지 설정될 수 있습니다. 옵션은 다음과 같습니다.
비디오 옵션 설명 LCD Brightness 전원에 따라 디스플레이 밝기를 설정할 수 있습니다(배터리 전원 및 AC 전원). LCD 밝기는 배터리 및 AC 어댑 터와 상관없습니다. 슬라이더를 사용하여 설정할 수 있습니다. 노트: 비디오 설정은 비디오 카드가 시스템에 장착되어 있을 때만 나타납니다. 보안 화면 옵션 옵션 설명 Admin Password 관리자 암호를 설정, 변경 또는 삭제할 수 있습니다. 노트: 시스템 암호 또는 하드 드라이브 암호를 설정하기 전에 관리자 암호를 설정해야 합니다. 관리자 암 호를 삭제하면 시스템 암호와 하드 드라이브 암호도 자동으로 삭제됩니다. 노트: 암호를 성공적으로 변경하면 즉시 적용됩니다. 기본 설정: 설정 안 함 System Password 시스템 암호를 설정, 변경 또는 삭제할 수 있습니다. 노트: 암호를 성공적으로 변경하면 즉시 적용됩니다.
옵션 설명 ● ● ● ● ● ● ● ● 지우기. 활성화된 명령의 PPI 무시 비활성화된 명령의 PPI 무시. Attestation enable(검증 사용)—기본적으로 활성화되어 있음 Key storage enable(키 스토리지 사용)—기본적으로 활성화되어 있음 SHA-256—기본적으로 활성화되어 있음 비활성화됨. Enabled(활성화됨) - 기본적으로 활성화되어 있음 노트: TPM 2.0을 업그레이드 또는 다운그레이드하려면 TPM 랩퍼 도구(소프트웨어)를 다운로드하십시 오. Computrace 선택사양의 Computrace 소프트웨어를 사용 또는 사용하지 않도록 설정할 수 있습니다. 옵션은 다음과 같습니 다. ● 비활성화. ● 사용 안 함. ● Activate(활성화)—기본적으로 활성화되어 있음 노트: Activate(활성화) 및 Disable(비활성화) 옵션은 기능을 영구적으로 활성화하거나 비활성화하므로 나 중에 변경할 수 없습니다.
옵션 설명 Custom Mode(사용자 지정 모드)를 활성화하면 PK, KEK, db 및 dbx 관련 옵션이 나타납니다. 옵션은 다음과 같습니다. ● ● ● ● ● ● 파일에 저장 - 키를 사용자가 선택한 파일에 저장합니다 파일의 키로 대체 - 현재 키를 사용자가 선택한 파일의 키로 대체합니다 파일의 키 추가 - 사용자가 선택한 파일의 키를 현재 데이터베이스에 추가합니다 삭제 - 선택한 키를 삭제합니다 모든 키 재설정 - 기본 설정으로 되돌립니다 모든 키 삭제 - 모든 키를 삭제합니다 노트: Custom Mode(사용자 지정 모드)를 비활성화하면, 모든 변경 사항이 삭제되고 키가 기본 설정으로 복원됩니다. Intel 소프트웨어 가드 확장 화면 옵션 옵션 설명 Intel SGX Enable 이 필드를 사용하면 기본 OS에서 코드 실행과 중요 정보 저장을 위한 보안 환경을 지정할 수 있습니다. 옵션은 다음과 같습니다. ● 비활성화됨.
옵션 설명 HyperThread Control(하이퍼 스 레딩 제어) 프로세서의 Hyper-Threading 기능을 사용하거나 사용하지 않도록 설정합니다. ● 비활성화됨 ● 활성 상태 기본 설정: Enabled(사용)가 선택됩니다. 전원 관리 화면 옵션 옵션 설명 AC Behavior AC 어댑터가 연결되어 있을 때 컴퓨터가 자동으로 켜지도록 하는 기능을 활성화 또는 비활성화할 수 있습니 다. 기본 설정: AC 절전 모드 해제가 선택되지 않습니다. Auto On Time 컴퓨터가 자동으로 켜지는 시간을 설정할 수 있습니다. 옵션은 다음과 같습니다: ● ● ● ● 비활성화됨 매일 평일 날짜 선택 기본 설정: 비활성 상태 USB Wake Support USB 장치가 시스템을 대기 모드로부터 재개하도록 설정할 수 있습니다. 노트: 이 기능은 AC 전원 어댑터가 연결되어 있을 때만 작동합니다.
옵션 설명 노트: 모든 배터리에 대해 충전 모드를 모두 이용할 수 있는 것은 아닙니다. 이 옵션을 활성화하려면 Advanced Battery Charge Configuration(고급 배터리 충전 구성) 옵션을 비활성화하십시오. 절전 모드 ● OS 자동 선택(기본적으로 활성화됨) Force S3 Type-C 커넥터 전 원 ● 7.5와트 ● 15와트(기본적으로 활성화됨) POST Behavior(POST 동작) 화면 옵션 옵션 설명 Adapter Warnings 특정 전원 어댑터 사용 시 시스템 설정(BIOS) 경고 메시지를 활성화 또는 비활성화할 수 있습니다. 기본 설정: 어댑터 경고 사용. Keypad (Embedded) 내장 키보드에 포함된 키패드를 활성화하는 두 가지 방법 중 하나를 선택할 수 있습니다. ● Fn 키만(기본값) ● Numlock으로 노트: 설치를 실행 중인 경우 이 옵션은 적용되지 않습니다. "Fn Key Only(Fn 키만)" 모드에서 설정할 수 있 습니다.
옵션 설명 MEBX Hotkey 시스템 부팅 시 MEBx 핫키 기능 사용 여부를 지정할 수 있습니다. enabled by default ● 비활성화됨 ● 활성 상태 기본 설정: 비활성 상태 가상화 지원 화면 옵션 옵션 설명 VT for Direct I/O 직접 I/O를 위해 Intel® Virtualization Technology가 제공하는 추가 하드웨어 기능을 활용하는 VMM(Virtual Machine Monitor)을 활성화하거나 비활성화합니다. 직접 I/O용 Intel VT 사용(기본값). Trusted Execution 이 옵션은 MVMM(Virtual Machine Monitor)이 Intel 가상화 기술이 제공하는 추가 하드웨어 기능을 활용할지 여 부를 지정합니다. 이 기능을 사용하려면 TPM 가상화 기술 및 직접 I/O용 가상화 기술을 활성화해야 합니다. Trusted Execution - 기본적으로 비활성화됩니다.
옵션 설명 Data Wipe 이 필드를 사용하면 모든 내부 스토리지 장치에서 데이터를 안전하게 지울 수 있습니다. 'Wipe on Next boot(다음 부팅 시 삭제)' 옵션은 기본적으로 활성화되어 있지 않습니다. 영향을 받는 장치 목록은 다음과 같습 니다. ● ● ● ● BIOS Recovery 내부 SATA HDD/SSD 내부 M.2 SATA SDD 내부 M.2 PCIe SSD 내장 eMMC 이 필드를 사용하면 사용자의 기본 하드 드라이브 또는 외부 USB 키의 복구 파일을 통해 손상된 BIOS 조건을 복구할 수 있습니다. ● BIOS Recovery from Hard Drive(하드 드라이브에서 BIOS 복구)—기본적으로 활성화되어 있음 ● Always perform integrity check(항상 무결성 검사 수행)—기본적으로 비활성화되어 있음 시스템 로그 옵션 설명 BIOS Events 시스템 설정(BIOS) POST 이벤트를 보거나 지울 수 있습니다.
USB 플래시 드라이브를 사용하는 BIOS 업데이트 시스템을 Windows에 로드할 수 없지만 BIOS를 업그레이드해야 하는 경우 다른 시스템을 사용하여 BIOS 파일을 다운로드하고 이것 을 부팅 가능한 USB 플래시 드라이브에 저장합니다. 1. BIOS 업데이트 .EXE 파일을 다른 시스템에 다운로드합니다. 2. Example: O9010A12.exe 파일을 부팅 가능한 USB 플래시 드라이브로 복사합니다. 3. USB 플래시 드라이브를 BIOS 업데이트가 필요한 시스템에 삽입합니다. 4. 시스템을 다시 시작하고 Dell 로고가 나타날 때 키를 눌러 부팅 메뉴를 표시합니다. 5. 화살표 키를 사용하여 USB 스토리지 장치를 선택하고 키를 누릅니다. 6. 시스템이 Diag C:\> 프롬프트로 부팅됩니다. 7. 전체 파일 이름 Example: O9010A12.exe을 입력하여 파일을 실행하고 키를 누릅니다. 8.
기존 시스템 설정 암호 삭제 또는 변경 기존 시스템 및 설정 암호를 삭제하거나 변경하려 시도하기 전에 암호 상태가 시스템 설정에서 잠금 해제인지 확인합니다. 암호 상태 가 잠금인 경우에는 기존 시스템 또는 설정 암호를 삭제하거나 변경할 수 없습니다. 시스템 설정에 들어가려면 전원이 켜진 직후 또는 재부팅 직후에 키를 누릅니다. 1. 시스템 BIOS 또는 시스템 설정 화면에서 시스템 보안을 선택하고 키를 누릅니다. System Security(시스템 보안) 화면이 표시됩니다. 2. System Security(시스템 보안) 화면에서 Password Status(암호 상태)를 Unlocked(잠금 해제)합니다. 3. System Password를 선택하고, 기존 시스템 암호를 변경 또는 삭제한 후 키 또는 키를 누릅니다. 4. Setup Password를 선택하고, 기존 설정 암호를 변경 또는 삭제한 후 키 또는 키를 누릅니다.
4 시스템:사양 노트: 제품은 지역에 따라 다를 수 있습니다. 다음은 현지 법률에 따라 컴퓨터와 함께 제공되어야 하는 사양입니다. 컴퓨터 구성 에 대한 자세한 정보를 보려면 Windows 운영 체제에서 도움말 및 지원으로 이동한 후 컴퓨터에 대한 정보를 보는 옵션을 선택하 십시오. 주제: • • • • • • • • • • • • • • • • • 지원되는 운영 체제 프로세서 사양 시스템:사양 메모리 사양 스토리지 사양 비디오 사양 오디오 사양 배터리 사양 AC 어댑터 사양 도킹 옵션 포트 및 커넥터 사양 통신 사양 카메라 사양 터치패드 사양 디스플레이 사양 외관 사양 환경 사양 지원되는 운영 체제 이 항목에서는 Latitude 7480 시스템에서 지원되는 운영 체제를 나열합니다. 표 3.
시스템:사양 기능 사양 칩셋 DRAM 버스 폭 64비트 플래시 EPROM SPI 128Mbits PCIe 버스 100MHz 외부 버스 주파수 DMI 3.0 - 8GT/s 메모리 사양 기능 사양 메모리 커넥터 SoDIMM 슬롯 2개 메모리 용량 4GB, 8GB, 16GB 및 32GB 메모리 종류 DDR4 SDRAM—2133MHz 최소 메모리 4GB 최대 메모리 32GB 스토리지 사양 이 노트북은 M.2 SATA SSD 및 M.2 PCIe NVMe SSD를 지원합니다. 옵션은 다음과 같습니다: ● M.2 SATA SSD ○ 128GB ○ 256GB ○ 512GB ○ 1TB ● M.2 PCIe NVMe SSD ○ ○ ○ ○ 128GB 256GB 512GB 1TB 비디오 사양 표 5.
노트: 도킹 스테이션을 통해 1개의 VGA, DisplayPort, HDMI를 지원합니다. 오디오 사양 기능 사양 종류 4채널 HD 오디오 컨트롤러 Realtek ALC3246 스테레오 변환 24비트—아날로그 대 디지털, 디지털 대 아날로그 내부 인터페이스 HD 오디오 외부 인터페이스 마이크 입력, 스테레오 헤드폰 및 헤드셋 콤보 커넥터 스피커 2개 내부 스피커 증폭기 채널당 2W(RMS) 볼륨 조절 단축키 배터리 사양 기능 사양 유형 ● 3셀 리튬 각형 배터리(ExpressCharge) ● 4셀 리튬 각형 배터리(ExpressCharge) 42Whr(3셀): 길이 200.5mm(7.89인치) 폭 95.9mm(3.78인치) 높이 5.7mm(0.22인치) 무게 185.0g(0.41파운드) 전압 11.4 VDC 60WHr(4셀): 길이 238mm(9.37인치) 폭 95.9mm(3.78인치) 높이 5.7mm(0.22인치) 무게 270g(0.
AC 어댑터 사양 기능 사양 유형 7.4mm 배럴 유형 65W 또는 90W 노트: 시스템은 65W 어댑터와 함께 제공되며 빠른 충전을 위해 90W 어댑터도 지원합니다. 입력 전압 100V AC ~ 240V AC 입력 전류—최대 1.7A/A 입력 주파수 50 ~ 60Hz 출력 전류 3.34A 및 4.62A 정격 출력 전압 19.5V DC 무게 치수 22 x 66 x 106mm(65W) 및 22 x 66 x 130(90W) 온도 범위—작동 시 0~40°C(32~104°F) 온도 범위—비 작동 -40°C ~ 70°C(-40°F ~ 158°F) 시 도킹 옵션 노트: 도킹 스테이션은 별도로 판매됩니다. 옵션 ● Dell Dock WD15 ● Dell Dock 스탠드 DS1000 ● Dell Thunderbolt Dock TB16 포트 및 커넥터 사양 표 6.
표 6. 온도 사양 (계속) 기능 사양 Express 카드 없음 AC 어댑터 E5 65W E5 65W 러그(인도만 해당) E5 90W E4 65W HF(BFR/PVC 프리) Power Companion 45W(Dura Ace) 하이브리드 파워 뱅크 및 어댑터(45W)(12"만, 14/15" 아님)(고속 충전 없음) 스마트 카드 리더 1개(옵션) 비디오 HDMI 1.4 통신 사양 기능 사양 네트워크 어댑터 인텔 i219LM 기가비트 이더넷 컨트롤러 10/100/1000Mb/s(RJ-45) 카메라 사양 노트: FHD 디스플레이를 포함하는 시스템은 또한 Windows Hello 기능을 지원하는 IR 카메라 옵션과 함께 제공됩니다. 기능 사양 유형 HD 고정 포커스 센서 유형 CMOS 센서 기술 이미징 속도 초당 최대 30 프레임 비디오 해상도 1280 x 720픽셀(0.
기능 사양 휘도 200니트 높이 205.6mm(8.09인치) 폭 320.9mm(12.63인치) 대각선 355.6mm(14.0인치) 최대 해상도 1366 x 768 메가픽셀 1.05 인치 당 픽셀(PPI) 112 대비율(최소) 300:2 재생률 60Hz 최대 가시 각도—가 +/- 40° 로 최대 가시 각도—세 +10/-30° 로 픽셀 피치 0.2265 x 0.2265mm 유형 - 14.0인치: 눈부심 방지 FHD - 비터치 휘도 300니트 높이 205.6mm(8.09인치) 폭 302.9mm(12.63인치) 대각선 355.6mm(14.0인치) 최대 해상도 1920 x 1080 메가픽셀 2.07 인치 당 픽셀(PPI) 157 대비율(최소) 600:1 재생률 60Hz 최대 가시 각도—가 +/-80° 로 최대 가시 각도—세 +/-80° 로 픽셀 피치 0.161 x 0.161mm 기능 사양 유형 - 14.
기능 사양 최대 가시 각도—가 +/-80° 로 최대 가시 각도—세 +/-80° 로 픽셀 피치 0.161 x 0.161mm 유형 - 14.0인치: QHD 눈부심 방지 - 터치 휘도 270 높이 206.6mm(8.13인치) 폭 327.8mm(12.90인치) 대각선 355.6mm—14.0인치 최대 해상도 2560 x 1440 메가픽셀 3.68 인치 당 픽셀(PPI) 210 대비율(최소) 600:1 재생률 60Hz 최대 가시 각도—가 +/-80° 로 최대 가시 각도—세 +/-80° 로 픽셀 피치 0.1209 × 0.1209mm 외관 사양 기능 사양 전면 높이—비터치 11.58mm(0.45인치) 후면 높이—비터치 18.41mm(0.72인치) 후면 높이—터치 18.41mm(0.72인치) 폭 331.0mm(13.03인치) 깊이 220.9mm(8.69인치) 무게—비터치 3셀 배터리 포함 1.36kg(3.01파운드) 환경 사양 표 7.
표 8. 상대 습도 - 사양 온도 사양 작동 시 10%~90%(비응축) 스토리지 5% ~ 95%(비응축) 표 9. 고도 - 최대 사양 온도 사양 작동 시 -15.2m~3,048m(-50~10,000ft) 비작동 시 -15.24m~10,668m(-50ft~35,000ft) 스토리지 5%~95%(비응축) 공기 중 오염 물질 수준 ISA S71.
5 시스템 설치 주제: • • • • • • • • • • • • • • • • • • • Boot Sequence 탐색 키 시스템 설치 옵션 일반 화면 옵션 시스템 구성 화면 옵션 비디오 보안 화면 옵션 보안 부팅 화면 옵션 Intel 소프트웨어 가드 확장 화면 옵션 성능 화면 옵션 전원 관리 화면 옵션 POST Behavior(POST 동작) 화면 옵션 관리 기능 가상화 지원 화면 옵션 무선 화면 옵션 유지 보수 화면 시스템 로그 Windows에서 BIOS 업데이트 시스템 및 설정 암호 Boot Sequence 부팅 순서를 사용하여 시스템 설치가 정의하는 부트 디바이스 순서를 생략하고 직접 특정 디바이스(예: 옵티컬 드라이브 또는 하드 드라이브)로 부팅할 수 있습니다. POST(Power-on Self Test) 중에 Dell 로고가 나타나면 다음 작업을 수행할 수 있습니다. ● F2 키를 눌러 시스템 설정에 액세스 ● 키를 눌러 1회 부팅 메뉴를 실행합니다.
키 탐색기 아래쪽 화살표 다음 필드로 이동합니다. Enter 선택한 필드에서 값을 선택하거나(해당하는 경우) 필드의 링크로 이동합니다. 스페이스바 드롭다운 목록(있는 경우)을 확장하거나 축소합니다. 탭 다음 작업 영역으로 이동합니다. Esc 기본 화면이 보일 때까지 이전 페이지로 이동합니다. 기본 화면에서 Esc 키를 누르면 저장하지 않은 변경 사항 을 저장하고 시스템을 다시 시작하라는 메시지가 표시됩니다. 시스템 설치 옵션 노트: 노트북 컴퓨터 및 장착된 디바이스에 따라 이 섹션에 나열된 항목이 표시되거나 표시되지 않을 수 있습니다. 일반 화면 옵션 이 섹션에는 컴퓨터의 기본 하드웨어 기능이 나열됩니다. 옵션 설명 System information 이 섹션에는 컴퓨터의 기본 하드웨어 기능이 나열됩니다. Battery Information 배터리 수명 및 AC 어댑터가 설치되어 있는지 여부를 표시합니다.
시스템 구성 화면 옵션 옵션 설명 Integrated NIC 내장형 네트워크 컨트롤러를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● Parallel Port 도킹 스테이션의 병렬 포트를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● Serial Port 비활성화됨. AT: 이 옵션은 기본적으로 활성화됩니다. PS2 ECP 내장형 직렬 포트를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● ● ● ● ● SATA Operation 비활성화됨. 활성 상태 Enable UEFI network stack(UEFI 네트워크 스택 활성화): 이 옵션은 기본적으로 활성화되어 있습니다. Enabled w/PXE(PXE와 함께 사용) 비활성화됨. COM1: 이 옵션은 기본적으로 활성화됩니다. COM2 COM3 COM4 내부 SATA 하드 드라이브 컨트롤러를 구성할 수 있습니다. 옵션은 다음과 같습니다. ● 비활성화됨.
옵션 설명 노트: USB 키보드와 마우스는 이러한 설정에 관계 없이 항상 BIOS 설정에서 작동합니다. USB PowerShare 이 필드는 USB PowerShare 기능의 동작을 구성합니다. 이 옵션으로 USB PowerShare 포트를 통해 저장된 시 스템 배터리 전력을 사용하여 외부 장치를 충전할 수 있습니다. 이 옵션은 기본적으로 비활성화되어 있습니 다. 오디오 이 필드는 내장형 오디오 컨트롤러를 활성화 또는 비활성화합니다. Enable Audio(오디오 사용) 옵션은 기본 적으로 선택되어 있습니다. 옵션은 다음과 같습니다. ● 마이크로폰 활성화(기본적으로 활성화) ● Enable Internal Speaker(내부 스피커 활성화) — 기본적으로 활성화 Keyboard Illumination 이 필드에서는 키보드 조명 기능의 작동 모드를 선택할 수 있습니다. 키보드 밝기 레벨은 0%에서 100%까지 설정될 수 있습니다. 옵션은 다음과 같습니다.
비디오 옵션 설명 LCD Brightness 전원에 따라 디스플레이 밝기를 설정할 수 있습니다(배터리 전원 및 AC 전원). LCD 밝기는 배터리 및 AC 어댑 터와 상관없습니다. 슬라이더를 사용하여 설정할 수 있습니다. 노트: 비디오 설정은 비디오 카드가 시스템에 장착되어 있을 때만 나타납니다. 보안 화면 옵션 옵션 설명 Admin Password 관리자 암호를 설정, 변경 또는 삭제할 수 있습니다. 노트: 시스템 암호 또는 하드 드라이브 암호를 설정하기 전에 관리자 암호를 설정해야 합니다. 관리자 암 호를 삭제하면 시스템 암호와 하드 드라이브 암호도 자동으로 삭제됩니다. 노트: 암호를 성공적으로 변경하면 즉시 적용됩니다. 기본 설정: 설정 안 함 System Password 시스템 암호를 설정, 변경 또는 삭제할 수 있습니다. 노트: 암호를 성공적으로 변경하면 즉시 적용됩니다.
옵션 설명 ● ● ● ● ● ● ● ● 지우기. 활성화된 명령의 PPI 무시 비활성화된 명령의 PPI 무시. Attestation enable(검증 사용)—기본적으로 활성화되어 있음 Key storage enable(키 스토리지 사용)—기본적으로 활성화되어 있음 SHA-256—기본적으로 활성화되어 있음 비활성화됨. Enabled(활성화됨) - 기본적으로 활성화되어 있음 노트: TPM 2.0을 업그레이드 또는 다운그레이드하려면 TPM 랩퍼 도구(소프트웨어)를 다운로드하십시 오. Computrace 선택사양의 Computrace 소프트웨어를 사용 또는 사용하지 않도록 설정할 수 있습니다. 옵션은 다음과 같습니 다. ● 비활성화. ● 사용 안 함. ● Activate(활성화)—기본적으로 활성화되어 있음 노트: Activate(활성화) 및 Disable(비활성화) 옵션은 기능을 영구적으로 활성화하거나 비활성화하므로 나 중에 변경할 수 없습니다.
옵션 설명 Custom Mode(사용자 지정 모드)를 활성화하면 PK, KEK, db 및 dbx 관련 옵션이 나타납니다. 옵션은 다음과 같습니다. ● ● ● ● ● ● 파일에 저장 - 키를 사용자가 선택한 파일에 저장합니다 파일의 키로 대체 - 현재 키를 사용자가 선택한 파일의 키로 대체합니다 파일의 키 추가 - 사용자가 선택한 파일의 키를 현재 데이터베이스에 추가합니다 삭제 - 선택한 키를 삭제합니다 모든 키 재설정 - 기본 설정으로 되돌립니다 모든 키 삭제 - 모든 키를 삭제합니다 노트: Custom Mode(사용자 지정 모드)를 비활성화하면, 모든 변경 사항이 삭제되고 키가 기본 설정으로 복원됩니다. Intel 소프트웨어 가드 확장 화면 옵션 옵션 설명 Intel SGX Enable 이 필드를 사용하면 기본 OS에서 코드 실행과 중요 정보 저장을 위한 보안 환경을 지정할 수 있습니다. 옵션은 다음과 같습니다. ● 비활성화됨.
옵션 설명 HyperThread Control(하이퍼 스 레딩 제어) 프로세서의 Hyper-Threading 기능을 사용하거나 사용하지 않도록 설정합니다. ● 비활성화됨 ● 활성 상태 기본 설정: Enabled(사용)가 선택됩니다. 전원 관리 화면 옵션 옵션 설명 AC Behavior AC 어댑터가 연결되어 있을 때 컴퓨터가 자동으로 켜지도록 하는 기능을 활성화 또는 비활성화할 수 있습니 다. 기본 설정: AC 절전 모드 해제가 선택되지 않습니다. Auto On Time 컴퓨터가 자동으로 켜지는 시간을 설정할 수 있습니다. 옵션은 다음과 같습니다: ● ● ● ● 비활성화됨 매일 평일 날짜 선택 기본 설정: 비활성 상태 USB Wake Support USB 장치가 시스템을 대기 모드로부터 재개하도록 설정할 수 있습니다. 노트: 이 기능은 AC 전원 어댑터가 연결되어 있을 때만 작동합니다.
옵션 설명 노트: 모든 배터리에 대해 충전 모드를 모두 이용할 수 있는 것은 아닙니다. 이 옵션을 활성화하려면 Advanced Battery Charge Configuration(고급 배터리 충전 구성) 옵션을 비활성화하십시오. 절전 모드 ● OS 자동 선택(기본적으로 활성화됨) Force S3 Type-C 커넥터 전 원 ● 7.5와트 ● 15와트(기본적으로 활성화됨) POST Behavior(POST 동작) 화면 옵션 옵션 설명 Adapter Warnings 특정 전원 어댑터 사용 시 시스템 설정(BIOS) 경고 메시지를 활성화 또는 비활성화할 수 있습니다. 기본 설정: 어댑터 경고 사용. Keypad (Embedded) 내장 키보드에 포함된 키패드를 활성화하는 두 가지 방법 중 하나를 선택할 수 있습니다. ● Fn 키만(기본값) ● Numlock으로 노트: 설치를 실행 중인 경우 이 옵션은 적용되지 않습니다. "Fn Key Only(Fn 키만)" 모드에서 설정할 수 있 습니다.
옵션 설명 MEBX Hotkey 시스템 부팅 시 MEBx 핫키 기능 사용 여부를 지정할 수 있습니다. enabled by default ● 비활성화됨 ● 활성 상태 기본 설정: 비활성 상태 가상화 지원 화면 옵션 옵션 설명 VT for Direct I/O 직접 I/O를 위해 Intel® Virtualization Technology가 제공하는 추가 하드웨어 기능을 활용하는 VMM(Virtual Machine Monitor)을 활성화하거나 비활성화합니다. 직접 I/O용 Intel VT 사용(기본값). Trusted Execution 이 옵션은 MVMM(Virtual Machine Monitor)이 Intel 가상화 기술이 제공하는 추가 하드웨어 기능을 활용할지 여 부를 지정합니다. 이 기능을 사용하려면 TPM 가상화 기술 및 직접 I/O용 가상화 기술을 활성화해야 합니다. Trusted Execution - 기본적으로 비활성화됩니다.
옵션 설명 Data Wipe 이 필드를 사용하면 모든 내부 스토리지 장치에서 데이터를 안전하게 지울 수 있습니다. 'Wipe on Next boot(다음 부팅 시 삭제)' 옵션은 기본적으로 활성화되어 있지 않습니다. 영향을 받는 장치 목록은 다음과 같습 니다. ● ● ● ● BIOS Recovery 내부 SATA HDD/SSD 내부 M.2 SATA SDD 내부 M.2 PCIe SSD 내장 eMMC 이 필드를 사용하면 사용자의 기본 하드 드라이브 또는 외부 USB 키의 복구 파일을 통해 손상된 BIOS 조건을 복구할 수 있습니다. ● BIOS Recovery from Hard Drive(하드 드라이브에서 BIOS 복구)—기본적으로 활성화되어 있음 ● Always perform integrity check(항상 무결성 검사 수행)—기본적으로 비활성화되어 있음 시스템 로그 옵션 설명 BIOS Events 시스템 설정(BIOS) POST 이벤트를 보거나 지울 수 있습니다.
시스템 및 설정 암호 표 10. 시스템 및 설정 암호 암호 유형 설명 시스템 암호 시스템 로그온하기 위해 입력해야 하는 암호. 설정 암호 컴퓨터의 BIOS 설정에 액세스하고 변경하기 위해 입력해야 하는 암호. 컴퓨터 보안을 위해 시스템 및 설정 암호를 생성할 수 있습니다. 주의: 암호 기능은 컴퓨터 데이터에 기본적인 수준의 보안을 제공합니다. 주의: 컴퓨터가 잠겨 있지 않고 사용하지 않는 경우에는 컴퓨터에 저장된 데이터에 누구라도 액세스할 수 있습니다. 노트: 시스템 및 설정 암호 기능은 비활성화되어 있습니다. 시스템 설정 암호 할당 설정 안 됨 상태일 때만 새 시스템 또는 관리자 암호를 할당할 수 있습니다. 시스템 설정에 들어가려면 전원이 켜진 직후 또는 재부팅 직후에 키를 누릅니다. 1. 시스템 BIOS 또는 시스템 설정 화면에서 보안을 선택하고 키를 누릅니다. Security (보안) 화면이 표시됩니다. 2.
6 문제 해결 주제: • ePSA(Enhanced Pre-Boot System Assessment) 진단 ePSA(Enhanced Pre-Boot System Assessment) 진단 ePSA 진단(시스템 진단이라고도 함) 프로그램은 하드웨어에 대해 완전한 검사를 수행합니다. ePSA는 BIOS에 내장되어 있으며 BIOS 에 의해 내부적으로 실행됩니다. 내장형 시스템 진단 프로그램은 특정 장치 그룹 또는 장치에 대해 일련의 옵션을 제공하여 사용자가 다음을 수행할 수 있게 합니다. ePSA 진단은 컴퓨터를 켜는 동안 버튼을 눌러 시작할 수 있습니다. ● ● ● ● ● ● 자동으로 테스트 또는 상호 작용 모드를 실행합니다. 테스트를 반복합니다. 테스트 결과를 표시 또는 저장합니다. 오류가 발생한 장치에 대한 추가 정보를 제공하기 위해 추가 테스트 옵션으로 세부 검사를 실행합니다. 테스트가 성공적으로 완료되었음을 알리는 상태 메시지를 봅니다.
7 Dell에 문의하기 노트: 인터넷에 연결되어 있지 않은 경우 구매 송장, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 확인할 수 있습니다. Dell은 다양한 온라인 및 전화 기반 지원과 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 1. Dell.com/support로 이동합니다. 2. 지원 카테고리를 선택합니다. 3. 페이지 맨 아래에 있는 Choose a Country/Region(국가/지역 선택) 드롭다운 메뉴에서 국가 또는 지역을 확인합니다. 4. 필요에 따라 해당 서비스 또는 지원 링크를 선택합니다.