Latitude 7490 用户手册 管制型号: P73G 管制类型: P73G002 October 2020 Rev.
注意、小心和警告 注: “注意”表示帮助您更好地使用该产品的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告: “警告”表示可能会导致财产损失、人身伤害甚至死亡。 © 2017-2020 Dell Inc. 或其子公司。保留所有权利。Dell、EMC 和其他商标是 Dell Inc.
目录 章 1: 拆装计算机内部组件.................................................................................................................. 6 安全防范措施........................................................................................................................................................................ 6 静电放电 — ESD 保护................................................................................................................................................... 6 ESD 现场服务套件............................
卸下 LED 板................................................................................................................................................................... 23 安装 LED 板................................................................................................................................................................... 24 智能卡模块.............................................................................................................................................................
热键组合............................................................................................................................................................................... 61 章 5: 系统设置程序......................................................................................................................... 62 引导菜单.............................................................................................................................................................................. 62 导航键........
1 拆装计算机内部组件 主题: • • • 安全防范措施 拆装计算机内部组件之前 拆装计算机内部组件之后 安全防范措施 安全预防措施一章详细介绍了在执行任何拆卸说明之前应采取的主要步骤。 在执行任何涉及拆卸或重新组装的安装或中断/修复过程之前,请遵守以下安全预防措施: ● ● ● ● ● ● 关闭系统和所有连接的外围设备。 断开系统和所有已连接的外围设备与交流电源的连接。 断开所有网络线缆、电话和电信线路与系统的连接。 拆装任何笔记本系统内部组件时,请使用 ESD 现场服务套件,以避免静电放电 (ESD) 损坏。 卸下系统组件后,小心地将卸下的组件放在防静电垫上。 穿戴具有绝缘橡胶鞋底的鞋子以减少产生静电的机会。 备用电源 带有备用电源的戴尔产品必须完全断电,然后才能打开包装。包含备用电源的系统在关闭时实际上会开机。内部电源使系统能够远 程开启(LAN 唤醒)和暂挂进入休眠模式,并且具有其他高级电源管理功能。 拔下电源并按住电源按钮 15 秒应释放系统板中的剩余电量。从笔记本卸下电池。 接合 接合是将两个或多个接地导体连接至同一个电源的一种方法。该操作可以通过使用现场服务静电放电 (ESD) 套件完
● 使用正确接地的 ESD 腕带。不再允许使用无线防静电腕带;它们无法提供充分的保护。随着对 ESD 损坏的敏感度增强,处理部 件之前接触机箱不能确保对部件提供足够的 ESD 保护。 ● 在静电安全的区域处理所有的静电敏感组件。如果可能,使用防静电的地板垫和工作台垫。 ● 在打开对静电敏感的组件的运输纸板箱时,要在准备安装此组件时再将其从防静电包装材料中取下。打开防静电包装之前,请务 必确保释放身体静电。 ● 在运输对静电敏感的组件前,将它置于防静电的容器或包装内。 ESD 现场服务套件 无监控的现场服务套件是最常使用的服务套件。每个现场服务套件包括三个主要部件:防静电垫子、腕带和联结线。 ESD 现场服务套件的组件 ESD 现场服务套件包含以下组件: ● 防静电垫子 – 防静电垫子可耗散电量,在维修过程中可用来放置部件。使用防静电垫子时,应正确佩戴腕带,并应使用联结线将 垫子连接到正在处理的系统上的裸金属。正确部署后,可以从 ESD 包中取出维修部件,然后直接放在垫子上。放置 ESD 敏感部 件的安全地方是您的手中、ESD 垫子上、系统中或包内。 ● 腕带和联结线 – 腕带和联结线可以直接连接您的手腕和
小心: 如果您的计算机具有 RJ45 端口,请首先从计算机上拔下电缆,以断开网络电缆的连接。 5. 断开计算机和所有连接的设备与各自电源插座的连接。 6. 打开显示屏。 7. 按住电源按钮几秒钟以导去系统板上的静电。 小心: 为防止触电,请始终在执行步骤 8 之前断开计算机与电源插座的连接。 小心: 为防止静电放电,请使用接地腕带或不时触摸未上漆的金属表面(例如计算机背面的连接器)以导去身上的静电。 8. 从相应的插槽中卸下所有已安装的 ExpressCard 或智能卡。 拆装计算机内部组件之后 完成所有更换步骤后,请确保在打开计算机前已连接好外部设备、插卡和电缆。 小心: 为避免损坏计算机,请仅使用专为此特定 Dell 计算机而设计的电池。请勿使用专用于其它 Dell 计算机的电池。 1. 连接所有外部设备(例如端口复制器或介质基座)并装回所有插卡(例如 ExpressCard)。 2. 将电话线或网络电缆连接到计算机。 小心: 要连接网络电缆,请先将电缆插入网络设备,然后将其插入计算机。 3. 将计算机和所有已连接设备连接至电源插座。 4.
2 卸下和安装组件 主题: • • • • • • • • • • • • • • • • • • • • • • • • • 建议工具 螺钉大小列表 用户识别模块卡 基座护盖 电池 固态硬盘 扬声器 币形电池 WWAN 卡 WLAN 卡 内存模块 散热器 LED 板 智能卡模块 触摸板按钮板 电源连接器端口 显示屏部件 触摸屏面板 显示屏挡板 非触摸屏面板 摄像机麦克风模块 显示屏铰接部件盖 系统板 键盘 掌垫 建议工具 执行本说明文件中的步骤时可能需要使用以下工具: ● 0 号梅花槽螺丝刀 ● 1 号梅花槽螺丝刀 ● 塑料划片 注: 0 号螺丝刀用于 0-1 螺钉,1 号螺丝刀用于 2-4 螺钉。 螺钉大小列表 表. 1: Latitude 7490 - 螺钉大小列表 组件 后盖 M2.5x 6.0 M2.5x5.0 M2.0 x 5.0 M2.5 x 4.0 M2.0x3.0 M2.0 x 2.5 M2.0 x 2.
表. 1: Latitude 7490 - 螺钉大小列表 (续) 组件 M2.5x 6.0 M2.5x5.0 M2.0 x 5.0 M2.5 x 4.0 固态驱动器 散热器和风扇 M2.0x3.0 M2.0 x 2.0 1 2 4 WWAN 卡 1 WLAN 卡 1 电源连接器端口 1 ESD 支架 EDP 支架 M2.0 x 2.5 2 1 触摸板按钮 2 指纹读取器 1 LED 板 1 智能卡读取器固定框架 2 显示屏铰接 6 显示屏面板 4 键盘支持板 18 键盘 5 系统板 3 USB Type C 支架 2 散热模块 4 DC In 支架 1 K-Lock 支架 1 用户识别模块卡 卸下 SIM 卡或 SIM 卡托盘 注: 卸下 SIM 卡或 SIM 卡托盘仅在附带 WWAN 模块的系统上可用。因此,卸下过程仅适用对于附带 WWAN 模块的系统。 小心: 在系统运行时卸下 SIM 卡可能会导致数据丢失或插卡损坏。确保您的系统处于关闭状态或网络连接已禁用。 1.
装回 SIM 卡 1. 2. 3. 4. 将回形针或 SIM 卡拆卸工具插入 SIM 卡托盘上的针孔。 使用塑料划片拉出 SIM 卡托盘 将 SIM 卡放置在托盘上。 将 SIM 卡托盘插入插槽。 卸下虚拟 SIM 卡托盘 对于附带 WWAN 卡的型号,必须先从系统中卸下 SIM 卡托盘,然后才能卸下系统板。要从系统中卸下 SIM 卡托盘,请按照拆卸部 分列出的步骤执行操作。 注: 对于仅附带无线网卡的型号,必须先从系统中卸下虚拟 SIM 卡托盘,然后才能卸下系统板。以下是卸下虚拟 SIM 卡托盘的步 骤: 1. 向内推动位于 SIM 卡插槽上的释放闩锁。 2.
基座护盖 卸下基座护盖 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 释放扬声器护盖: a. 拧下将基座护盖固定至系统的八颗 (M2.5 x 6.0) 固定螺钉 [1]。 注: 拧下螺钉时,请务必小心。确定螺丝刀的角度与螺钉(底部两颗)头匹配,以避免可能的螺钉头脱落。 b. 使用塑料划片,以从边缘释放基座护盖 [2]。 3.
安装基座护盖 1. 将基座护盖卡舌与系统机边缘的插槽对齐。 2. 按下护盖边缘,直到卡入到位。 3. 要将基座护盖固定至系统,拧紧八颗 (M2.5 x 6.0) 固定螺钉。 注: 拧紧螺钉时,请务必小心。确定螺丝刀的角度与螺钉头匹配,以避免可能的螺钉头脱落。 4.
● 如果电池因卡入计算机导致膨胀,请勿尝试通过刺穿、弯曲或弄碎锂电池的方式将其取出,因为这十分危险。在此类情况 下,请联系戴尔技术支持以获取帮助。请参阅 www.dell.com/contactdell。 ● 请始终从 www.dell.com 或授权戴尔合作伙伴和经销商购买正版电池。 卸下电池 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下基座盖。 3. 取出电池: a. 断开电池电缆与系统板上的连接器的连接 [1]。 注: Latitude 配备 3 芯或 4 芯电池,需要先取下电池,然后再更换客户可更换单元 (CRU) 部件。因此执行任何拆卸过程 时,应在拆除底盖后立即断开电池连接。为了断开系统的所有电源并防止系统意外接通组件电源和导致组件短路,此步 骤是必需的。 b. 拧下将电池固定至计算机的两颗 (M2.0 x 5.0) 螺钉 [2]。 注: 一个 3 芯电池只有一个螺钉,而 4 芯电池有两个螺钉。因此,下图显示了 4 芯电池。 c. 从系统中提起电池 [3]。 安装电池 1.
注: 小型电池(3 芯)有一颗螺钉,大型电池(4 芯)有两颗螺钉。 4. 安装基座盖。 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 固态硬盘 卸下固态硬盘 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下基座盖。 3. 从系统板上的连接器中断开电池电缆的连接。 4. 要卸下固态硬盘: a. 拧下固定固态硬盘支架的两颗 (M2.0 x 3.0) 固定螺钉 [1]。 b. 卸下固态硬盘支架(可选)[2]。 c. 从系统卸下固态硬盘 [3]。 安装固态硬盘 1. 将固态硬盘插入连接器。 2.
3. 拧紧两颗 (M2.0 x 3.0) 螺钉以将固态硬盘固定到固态硬盘支架,然后翻转掌垫。 4. 将电池电缆连接至系统板上的连接器。 5. 安装基座护盖。 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 扬声器 卸下扬声器模块 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下基座盖。 3. 从系统板上的连接器中断开电池电缆的连接。 4. 要释放扬声器模块,请执行以下操作: a. 断开扬声器电缆与系统板上连接器的连接 [1]。 注: 使用塑料划片以从连接器释放线缆。请勿拉动电缆,因为其可能会导致破裂 b. 从触摸板按钮侧面的两个布线固定夹中抽出扬声器线缆 [2]。 c. 撕下将扬声器线缆固定至触摸板的胶带 [3]。 5.
安装扬声器模块 1. 将扬声器模块放入系统上的插槽中。 2. 将扬声器线缆穿过系统上的固定片布线。 注: 对于 Latitude 7490,必须在掌垫上布线通道的下方正确布置扬声器线缆,并沿触摸板按钮底部边缘布置在布线通道中。 然后,使用附加到扬声器线缆的胶带,将其固定至触摸板按钮。 3. 将扬声器电缆连接到系统板上的连接器。 4. 将电池电缆连接至系统板上的连接器。 5. 安装基座护盖。 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 币形电池 卸下币形电池 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 3. 断开电池的连接。 4. 卸下币形电池: a.
注: 卸下或装回 Latitude 7490 的 RTC 电池或系统板时,必须在布线通道中布置 RTC 电池线缆并将其固定到系统板上的槽 口中。 b. 提起币形电池,以将其从胶带中释放 [2]。 注: 当卸下或装回 Latitude 7290 的 RTC 电池或系统板时,RTC 电池必须放置到位并使用胶带粘到指纹读取器支架。 安装币形电池 1. 将币形电池粘到计算机插槽中。 2. 穿过布线通道布置币形电池线缆,然后连接线缆。 3. 将币形电池线缆连接至系统板上的连接器。 注: 卸下或装回 Latitude 7490 的 RTC 电池或系统板时,必须在布线通道中布置 RTC 电池线缆并将其固定到系统板上的槽口 中。 4. 重新连接电池。 5. 安装以下组件: a. 基座护盖 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 WWAN 卡 卸下 WWAN 卡 1.
2. 卸下基座盖。 3. 从系统板上的连接器中断开电池电缆的连接。 4. 要卸下 WWAN 卡: a. 拧下将 WWAN 支架固定至 WWAN 卡的 M2.0 x 3.0 螺钉 [1]。 b. 提起固定 WWAN 卡的 WWAN 支架 [2]。 c. 断开 WWAN 线缆与 WWAN 卡上连接器的连接 [3]。 注: 系统板的布线垫中有胶粘垫,可固定无线和 WWAN 卡。卸下无线或 WWAN 卡需要少量额外的强制力量,以从胶粘垫上 分离卡。 5. 要卸下 WWAN 卡: 安装 WWAN 卡 1. 将 WWAN 卡插入系统板上的连接器。 2. 将 WWAN 电缆连接到 WWAN 卡上的连接器。 3. 放置金属支架并拧紧 M2.0 x 3.0 螺钉,以将其固定至计算机。 4. 将电池电缆连接至系统板上的连接器。 5. 安装基座护盖。 6.
WLAN 卡 卸下 WLAN 卡 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下基座盖。 3. 从系统板上的连接器中断开电池电缆的连接。 4. 要卸下 WLAN 卡: a. 拧下将金属支架固定至 WLAN 卡的 M2.0 x 3.0 螺钉 [1]。 b. 抬起金属支架 [2]。 c. 断开 WLAN 电缆与 WLAN 卡上连接器的连接 [3]。 注: 系统板的布线垫中有胶粘垫,可固定无线和 WWAN 卡。卸下无线或 WWAN 卡需要少量额外的强制力量,以从胶粘 垫上分离卡。 d. 从系统中卸下 WLAN 卡 [4]。 安装 WLAN 卡 1. 将 WLAN 卡插入系统板上的连接器。 2. 将 WLAN 电缆连接到 WLAN 卡上的连接器。 3. 放置金属支架并拧紧 M2.0 x 3.0 螺钉,以将其固定至 WLAN 卡。 注: 安装无线和 WWAN 天线时,必须在系统板上的布线垫/固定夹中正确布置无线和 WWAN 天线。对于仅附带无线网卡的型 号,技术人员必须始终确保使用保护套来隔离天线连接器,然后再重新装配系统。 4.
5. 安装基座护盖。 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 内存模块 卸下内存模块 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下基座盖。 3. 从系统板上的连接器中断开电池电缆的连接。 4. 要卸下内存模块: a. 拉动固定内存模块的固定夹,直至内存模块弹起 [1]。 b. 将内存模块从系统板上的连接器中卸下 [2]。 安装内存模块 1. 将模块插入连接器,然后将模块向下按压到固定夹上,直至其卡入。 2. 将电池电缆连接至系统板上的连接器。 3. 安装基座护盖。 4.
散热器 卸下散热器部件 散热器部件由散热器和系统风扇组成。 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 b. 电池 3. 卸下散热器部件: 注: 要确定螺钉的数量,请参阅螺钉列表。 a. 拧下用于固定系统风扇的 2 颗 (M2.0 x 5.0) 螺钉以及将散热器固定至系统板的 4 颗 (M2.0 x 3.0) [2]。 注: 按照插图编号的顺序拧下螺钉 [1、2、3、4](如散热器上所示)。 b. 从系统板中提起并翻转散热器部件。 c. 断开风扇电缆与系统板的连接 [1]。 d. 将散热器部件与系统分离。 安装散热器部件 散热器部件由散热器和系统风扇组成。 1. 将散热器部件与系统板上的螺钉固定器对齐。 2. 将风扇电缆连接至系统板上的连接器。 3. 拧上将散热器部件固定至系统板的 M2.0 x 3.
注: 按照系统板上指示的插图编号顺序拧上螺钉 [1、2、3、4]。 4. 安装以下组件: a. 电池 b. 基座护盖 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 LED 板 卸下 LED 板 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 b. 电池 3. 要卸下 LED 板: a. 断开 LED 电缆与 LED 板的连接 [1]。 小心: 避免拉动电缆,因为它可能会导致电缆连接器损坏。您应使用塑料划片推动电缆连接器的边缘,以释放 LED 电 缆。 b. 拧下将 LED 板固定至系统的 M2.0 x 2.5 螺钉 [2]。 c.
安装 LED 板 1. 将 LED 板插入计算机的插槽。 2. 拧上 M2.0 x 2.5 螺钉以固定 LED 板。 3. 将 LED 板电缆连接到 LED 板。 注: 对于 Latitude 7490,LED 子板缆线必须布置在掌垫上固定闩锁的下方,并且标签应放到系统板下方 4. 安装以下组件: a. 电池 b. 基座护盖 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 智能卡模块 卸下智能卡固定框架 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 b. 电池 c. PCIe SSD 卡 3. 要断开智能卡电缆的连接: a. 断开智能卡电缆的连接 [1]。 b. 提起粘附到触摸板模块的智能卡电缆 [2]。 4.
a. 拧下将智能卡固定框架固定至系统的两颗 (M2.0 x 3.0) 螺钉 [1]。 b. 滑动智能卡固定框架,并将其提离系统 [2]。 安装智能卡固定框架 1. 将智能卡固定框架滑入插槽,以与系统上的卡舌对齐。 2. 拧上将智能卡固定框架固定到系统的两颗 (M2.0 x 3.0) 螺钉。 3. 粘上智能卡电缆并将其连接至系统上的连接器。 4. 安装以下组件: a. PCIe SSD 卡 b. 电池 c. 基座护盖 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 触摸板按钮板 卸下触摸板按钮板 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 b. 电池 c.
d. 智能卡模块 3. 要卸下触摸板按钮板: a. 断开触摸板按钮板电缆与触摸板的连接 [1]。 注: 触摸板按钮板电缆的位置在智能卡电缆下面。 b. 拧下固定触摸板按钮板的两颗 (M2.0 x 3.0) 螺钉 [2]。 注: 要确定螺钉,请参阅螺钉列表。 c. 从系统中提起触摸板按钮板 [3]。 安装触摸板按钮板 1. 将触摸板按钮板插入插槽,以将卡舌与系统上的凹槽对齐。 2. 拧上将触摸板按钮板固定到系统的两颗 (M2.0 x 3.0) 螺钉。 3. 将触摸板按钮板电缆连接至触摸板上的连接器。 4. 安装以下组件: a. b. c. d. 智能卡模块 扬声器 电池 基座护盖 5.
电源连接器端口 卸下电源连接器端口 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 基座护盖 b. 电池 3. 卸下电源连接器端口的方法是: a. 断开电源连接器端口与系统板的连接 [1]。 注: 使用塑料划片以从连接器释放电缆。请勿拉动电缆,因为其可能会导致破裂 b. 拧下 M2.0 x 3.0 螺钉,以释放电源连接器端口上的金属支架 [2]。 c. 从系统中提起金属支架 [3]。 d. 将电源连接器端口从计算机中卸下 [4]。 安装电源连接器端口 1. 将电源连接器端口安装到系统上的插槽中。 2. 将金属支架放在电源连接器端口上。 3. 拧上 M2.0 x 3.0 螺钉以将电源连接器端口固定至系统。 4. 将电源连接器端口电缆连接至系统板上的连接器。 5. 安装以下组件: a.
b. 基座护盖 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 显示屏部件 卸下显示屏部件 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. 基座护盖 电池 WLAN 卡 WWAN 卡 注: 要确定螺钉数量,请参阅螺钉列表 3. 要卸下显示屏部件,请完成下列操作: a. 断开 IR 摄像头线缆与系统板的连接 [1]。 b. 从布线通道中拔下 WLAN 和 WWAN 线缆 [2]。 c. 卸下固定 eDP 支架的 M2.0x3.0 螺钉 [3]。 注: Latitude 7290 的显示屏线缆通过显示屏支架和一片胶带固定,附在系统板上的电源适配器连接器上。卸下显示屏部件 或系统板时,必须卸下显示屏支架,并且必须剥离胶带以便断开显示屏线缆的连接。 d. 从 eDP 线缆提起 eDP 支架 [4]。 e. 提起 eDP 线缆,使其断开与系统板上的连接器的连接 [5]。 f.
4. 要卸下显示屏部件,请完成下列操作: a. 打开计算机显示屏并将其平放(以 180 度角度)在平坦的表面上。 b. 拧下将显示屏转轴固定至显示屏部件的六颗 (M2.5 x 3.5) 螺钉 [1]。 c.
安装显示屏部件 1. 将计算机基座置于干净平坦的表面上。 2. 安装显示屏部件,使其与系统上的显示屏转轴固定器对齐。 3. 握住显示屏部件,拧上六颗 (M2.5 x 3.5) 螺钉,将显示屏转轴固定在包含系统装置的系统显示屏部件。 4. 从布线通道对 eDP 线缆布线。 5. 粘上胶带以将 eDP 线缆(显示屏线缆)固定至系统板。 6. 将 eDP 线缆连接至系统板上的连接器。 注: WLAN 和 WWAN 天线必须正确地布线到系统板上的布线盘中,并且必须使用防护胶套来隔离天线连接器。 7. 将 eDP 金属支架安装在 eDP 线缆上,并拧紧 M2.0 x 3.0 螺钉。 8. 将 IR 摄像头线缆连接至系统板。 9. 穿过布线通道布置 WLAN 和 WWAN 线缆。 10. 安装以下组件: a. b. c. d. WLAN 卡 WWAN 卡 电池 基座护盖 11. 按照“拆装计算机内部组件之后”中的步骤进行操作。 触摸屏面板 卸下触摸屏面板 注: 触摸屏面板卸下步骤仅适用于带有触摸屏配置的系统。 1.
2. 卸下以下组件: a. b. c. d. e. 基座护盖 电池 WLAN 卡 WWAN 卡 显示屏部件 3. 要卸下触摸屏面板,请执行下列操作: a. 使用塑料划片松开显示屏面板的边缘。 b. c. d. e.
4. 将显示屏挡板从显示屏部件卸下。 安装触摸屏面板 注: 触摸屏面板的安装步骤仅适用于带有触摸屏配置的系统。 1. 将显示屏面板置于显示屏部件上。 2. 重新连接 IR 线缆和 eDP 线缆。 3. 装回胶带和聚脂薄膜屏蔽带。 4. 按压显示屏面板的边缘,直至将其卡入显示屏部件。 5. 安装以下组件: a. b. c. d. e. 显示屏部件 WLAN 卡 WWAN 卡 电池 基座护盖 6.
1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 基座护盖 电池 WLAN 卡 WWAN 卡 显示屏部件 3. 要卸下显示屏挡板,请执行下列操作: 小心: LCD 挡板上使用的粘胶可将 LCD 挡板与 LCD 本身密封在一起,当粘胶的粘性很强时,往往会粘牢 LCD 部件,这使得 很难卸下挡板,因此在尝试撬开这两个部件时,可能会将层剥落或者弄碎玻璃。 a. 使用塑料划片,找到凹槽以松开显示屏挡板的底部边缘 [1]。 b. 松开显示屏边缘上的卡舌 [2、3、4]。 小心: LCD 挡板上使用的粘胶可将 LCD 挡板与 LCD 本身密封在一起,在边缘撬动,试着释放挡板。在尝试强力撬开这两个 部件时,密封胶可能会将层剥落或弄碎玻璃。 4. 将显示屏挡板从显示屏部件卸下。 安装显示屏挡板(非触摸) 注: 显示屏挡板的安装步骤仅适用于非触摸屏配置。 1. 将显示屏挡板置于显示屏部件上。 2. 按下显示屏挡板的边缘,直至将其卡入显示屏部件。 注: 使用粘胶将显示屏挡板固定在显示屏面板上。 3. 安装以下组件: a.
b. c. d. e. WLAN 卡 WWAN 卡 电池 基座护盖 4. 按照“拆装计算机内部组件之后”中的步骤进行操作。 非触摸屏面板 卸下显示屏面板(非触摸) 注: 显示屏面板的卸下步骤仅适用于非触摸屏配置。 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. f. g. 基座护盖 电池 WLAN 卡 WWAN 卡 显示屏部件 显示屏挡板 转轴护盖 3. 要卸下显示屏面板,请执行下列操作: a. 拧下面板上的两颗 (M2.0 x 2.0) 螺钉 [1]。 b. 提起显示屏面板的底部边缘 [2]。 c.
d. 将显示屏连接器胶带从显示屏面板中剥下 [1]。 e. 剥下将显示屏线缆固定至显示屏面板背面的聚脂薄膜胶带 [2]。 f. 提起金属卡舌,然后断开显示屏线缆与显示屏面板背面的连接 [3、4]。 g.
安装显示屏面板(非触摸) 注: 显示屏面板的安装步骤仅适用于非触摸屏配置。 1. 将显示屏线缆连接至显示屏面板的背面。 注: 对于 Latitude 7490,LED 子板线缆必须在掌托上的固定闩锁下进行布线,并且应将标签置于系统板下方。 2. 粘上聚脂薄膜胶带,将显示屏线缆固定至显示屏面板的背面。 3. 将显示屏连接器胶带粘到显示屏面板上。 4. 将显示屏面板翻转过来,然后朝向系统滑动显示屏面板。 5. 将两颗 (M2.0 x 2.0) 螺钉装回面板上。 6. 安装以下组件: a. b. c. d. e. f. g. 挡板 转轴护盖 显示屏部件 WLAN 卡 WWAN 卡 电池 基座护盖 7. 按照“拆装计算机内部组件之后”中的步骤进行操作。 摄像机麦克风模块 卸下摄像头麦克风模块 麦克风摄像头模块的卸下步骤仅适用于非触摸屏配置。 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. f. g. 基座护盖 电池 WLAN 卡 WWAN 卡 显示屏部件 挡板 显示屏转轴 3. 要卸下摄像头麦克风模块,请执行下列操作: a.
4. 要卸下摄像头麦克风模块,请执行下列操作: a. 剥下盖在摄像头麦克风模块的两片导电胶带 [1]。 注: 导电胶带是独立于摄像头模块的一个部件,必须先将其剥下,然后在装回摄像头麦克风模块时重新粘上。 b. 提起摄像头麦克风模块 [2]。 c. 断开摄像头 FPC 与摄像头模块的连接 [3]。 d.
安装摄像头 安装步骤仅适用于附带非触摸屏配置的系统。 1. 将摄像头模块插入显示屏部件上的插槽中。 2. 连接摄像头线缆。 3. 安装以下组件: a. b. c. d. e. f. g. h. 显示屏挡板 显示屏部件 显示屏转轴 卸下显示屏面板 WLAN 卡 WWAN 卡 电池 基座护盖 4.
显示屏铰接部件盖 卸下显示屏铰接部件盖 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 基座护盖 电池 WLAN 卡 WWAN 卡 显示屏部件 3. 从左向右滑动铰接部件帽,然后从显示屏面板上释放并卸下显示屏铰接部件帽。 安装显示屏铰接部件护盖 1. 将显示屏铰接部件护帽放到插槽上,然后将其向后滑动以装入显示屏部件。 注: 必须在左侧显示屏铰接部件周围的布线通道中正确布置显示屏缆线、触控传感器缆线(适用于附带触摸屏部件的型号) 和 ASA 天线缆线(适用于附带 Infinity 挡板的型号)。然后,使用附加到扬声器缆线的胶带,将其固定至显示屏后盖。 2. 安装以下组件: a. b. c. d. e. 显示屏部件 WLAN 卡 WWAN 卡 电池 基座护盖 3.
系统板 卸下系统板 1. 按照拆装计算机内部组件之前中的步骤执行操作。 注: 如果您的计算机配有 WWAN 卡,则需要卸下挡片 SIM 卡托盘。 2. 卸下以下组件: a. b. c. d. e. f. g. h. i. SIM 卡 虚拟 SIM 卡托盘 基座护盖 电池 内存模块 PCIe SSD WLAN 卡 WWAN 卡 散热器部件 要确定螺钉,请参阅螺钉列表 3. 卸下内存模块支架: a. 拧下将内存模块支架固定至系统板的两颗 (M2.0 x 3.0) 螺钉 [1]。 b. 从系统板提起内存模块支架 [2]。 4. 断开 eDP 线缆的连接:显示屏部件 5. 要断开线缆的连接: 注: 断开扬声器、LED 板、币形电池和电源连接器端口线缆的连接,然后使用塑料划片从连接器释放线缆。请勿拉动线缆, 因为其可能会导致破裂 a. 扬声器线缆 [1] b.
c. 币形电池线缆 [3] d. 触摸板线缆和 USH 板线缆的连接 [4] e. 电源连接器端口 [5] 6. 要卸下系统板: a. 卸下 USB type-C 支架。 该图未显示如何卸下 USB type-C 支架。 b. 拧下用于固定系统板的三颗(M2.0 x 5.0)螺钉 [1]。 c.
7. 拧下固定 USB Type-C 支架的两颗 (M2.0 x 5.0) 螺钉。 8.
注: 在系统板上卸下或重新安装 USB Type-C 支架时,技术人员必须将系统板放在 ESD 垫上,以免损坏。 安装系统板 1. 将系统板与系统上的螺孔对齐。 2. 拧上 M2.0 x 3.0 螺钉以将系统板固定至系统。 3. 将扬声器、LED 板、币形电池、触摸板和 USH 电缆以及电源连接器和电缆连接至系统板上的连接器。 4. 将 eDP 电缆连接至系统板上的连接器。 5. 将金属支架放到 eDP 缆线上方,然后拧上 M2.0 x 3.0 螺钉以固定。 6. 将金属支架放到内存模块连接器上,然后拧紧将其固定至系统的 M2.0 x 3.0 螺钉。 注: 更换系统板不包括 SIM 卡托盘(如果有)、USB Type-C 支架和 DDR ESD 支架,并且需要转换。 7. 安装以下组件: a. b. c. d. e. f. g. h. i. 散热器 WLAN 卡 WWAN 卡 PCIe SSD 卡 内存模块 电池 基座护盖 虚拟 SIM 卡托盘 SIM 卡 8. 按照“拆装计算机内部组件之后”中的步骤进行操作。 键盘 卸下键盘部件 注: 键盘和键盘托盘合称为键盘部件。 1.
2. 卸下: a. b. c. d. e. f. g. h. 基座护盖 电池 内存模块 PCIe SSD WLAN 卡 WWAN 卡 散热器部件 系统板 3. 断开电缆与在掌垫端的连接: a. 键盘电缆 [1] b. 键盘背光缆线 [2]、USH 板缆线(可选) c. 触摸板和 USH 板电缆 [3、4] 4. 卸下键盘部件: 注: 要确定螺钉,请参阅螺钉列表 a. 拧下固定键盘的 18 颗 (M2.0 x 2.5) 螺钉 [1]。 b.
从键盘托盘卸下键盘 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下键盘部件。 3. 拧下将键盘固定至键盘部件的五颗 M2.0 x 2.0 螺钉。 4. 将键盘从键盘托盘中提起。 将键盘安装至键盘托盘 1.
2. 拧紧五颗 M2.0 x 2.0 螺钉,以将键盘固定至键盘托盘。 3. 安装键盘部件。 安装键盘部件 注: 键盘和键盘托盘合称为键盘部件。 注: 键盘的格架侧面有多个卡点,必须在卡点稳固地向下按压,以便固定并匹配到更换键盘。 1. 将键盘部件与计算机上的螺钉固定器对齐。 2. 拧紧将键盘固定至机箱的 M2.0 x 2.5 螺钉。 3. 将键盘线缆、USH 板线缆(可选)、键盘背光线缆和触摸板线缆连接至触摸板按钮板上的连接器。 4. 安装以下组件: a. b. c. d. e. f. g. h. 系统板 散热器 WLAN 卡 WWAN 卡 PCIe SSD 卡 内存模块 电池 基座护盖 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 掌垫 装回掌垫 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. f. g. h.
i. 电源连接器端口 j. 币形电池 k. 扬声器 剩下的组件是掌垫。 3. 装回掌垫。 4. 安装以下组件: a. b. c. d. e. f. g. h. i. j. k. 扬声器 币形电池 电源连接器端口 系统板 散热器 WLAN 卡 WWAN 卡 PCIe SSD 卡 内存模块 电池 基座护盖 5.
3 技术和组件 本章详细介绍系统中提供的技术和组件。 主题: • • • • • DDR4 HDMI 1.4 USB 功能 USB Type-C 带 USB Type-C 的 Thunderbolt DDR4 DDR4(双倍数据速率第四代)内存是 DDR2 和 DDR3 技术的后继产品,其速度更快,并且最高支持 512 GB 容量,而 DDR3 的最大 内存仅 128 GB/DIMM。DDR4 同步动态随机存取内存的键位与 SDRAM 和 DDR 不同,以避免用户在系统中安装错误的内存类型。 DDR4 所需电压低 20%,仅为 1.2 V,而 DDR3 需要 1.
DDR4 模块具有弧形边缘,有助于插入并缓解内存安装期间对 PCB 的挤压。 图 3: 弧形边缘 内存错误 系统上的内存错误将显示新的 ON-FLASH-FLASH 或 ON-FLASH-ON 故障代码。如果所有内存出现故障,则 LCD 不会打开。针对可 能的内存故障进行故障排除的方法如下:在系统底部或键盘下(适用于某些便携式系统)的内存连接器中,试用已知的运行良好的 内存模块。 注: DDR4 内存嵌入在板上,并且不是所示的可更换 DIMM。 HDMI 1.4 此主题介绍 HDMI 1.4 及其功能和优势。 HDMI(高保真多媒体接口)是一个业界支持的、未压缩的全数字音频/视频接口。HDMI 在任何兼容数字音频/视频源之间提供接 口,例如 DVD 播放器、音频/视频接收器和兼容的数字音频/视频显示器,如数字电视 (DTV)。HDMI 电视和 DVD 播放器的意向用 于。主要优势是电缆缩减和内容保护配置。HDMI 支持标准的、增强的或高保真视频,以及单个电缆上的多信道数字音频。 注: HDMI 1.4 将提供 5.1 声道音频支持。 HDMI 1.
表. 2: USB 的演变 类型 数据传输速率 类别 推出年份 USB 2.0 480 Mbps 高速 2000 USB 3.0/USB 3.1 第 1 代 5 Gbps 超高速 2010 USB 3.1 Gen 2 10 Gbps 超高速 2013 USB 3.0/USB 3.1 Gen 1(超高速 USB) 多年来,USB 2.0 一直稳定地作为 PC 界的实际接口标准,相关设备已售出 60 亿台,而且在空前快速的计算硬件和空前巨大的带宽 需求下,其需要更大的速度提升。USB 3.0/USB 3.1 Gen 1 凭借理论上比其前代产品快 10 倍的速度,最终满足了消费者的需求。简而 言之,USB 3.1 Gen 1 功能如下所示: ● ● ● ● ● ● 更高的传输速率(高达 5 Gbps) 增加了最大总线功率以及增加了设备电流引出,更好地适应耗电设备 新的电源管理功能 全双工数据传输和新传输类型支持 向后 USB 2.0 兼容性 新连接器和电缆 下述主题介绍了有关 USB 3.0/USB 3.1 Gen 1 的一些最常见问题。 速度 当前,最新的 USB 3.
值。同样,USB 3.0/USB 3.1 Gen 1 连接也绝不会实现 4.8 Gbps 的速率。我们很可能在现实世界的开销方面看到高达 400 MB/s 的速 率。USB 3.0/USB 3.1 Gen 1 的这一速率比 USB 2.0 提高了 10 倍。 应用程序 USB 3.0/USB 3.1 Gen 1 提高了速度,使设备能够提供更好的整体体验。以前,几乎无法支持 USB 视频(从最大分辨率、延迟和视频 压缩的角度来看都是如此),不难想象到,将带宽增加 5-10 倍后,USB 视频解决方案的性能会显著提升。单链路 DVI 需要将近 2 Gbps 吞吐量。当限制为 480 Mbps 时,5 Gbps 更具前景。通过承诺的 4.8 Gbps 速度,之前未进入 USB 范围的某些产品(例如,外 部 RAID 存储系统)将采用此标准。 下面列出了部分可用的超高速 USB 3.0/USB 3.1 Gen 1 产品: ● ● ● ● ● ● ● ● ● ● 外部台式机 USB 3.0/USB 3.1 Gen 1 硬盘 便携式 USB 3.0/USB 3.1 Gen 1 硬盘 USB 3.0/USB 3.
USB Type-C 和 USB 3.1 USB 3.1 是新的 USB 标准。USB 3 的理论带宽为 5 Gbps,而 USB 3.1 第 2 代为 10 Gbps。带宽倍增,速度堪比第一代 Thunderbolt 连 接器。USB Type-C 与 USB 3.1 不同。USB Type-C 仅仅是接口类型,其基础即使可能仅仅是 USB 2 或 USB 3.0。实际上,Nokia 的 N1 Android 平板电脑使用 USB Type-C 连接器,但其基础技术是 USB 2.0 — 甚至不是 USB 3.
4 系统规格 主题: • • 技术规格 热键组合 技术规格 注: 所提供的配置可能会因地区的不同而有所差异。以下仅是依照法律规定随计算机附带的规格。有关计算机配置的详情,请转 至 Windows 操作系统中的帮助和支持,然后选择选项以查看有关计算机的信息。 表. 3: 规格 类型 功能 处理器系列 英特尔酷睿 i5-8250U(四核,3.4GHz,6M 高速缓存,15 W) 英特尔酷睿 i5-8350U(四核,3.6GHz,6M 高速缓存,15 W)博锐 英特尔酷睿 i7-8650U(四核,3.9 GHz,8M 高速缓存,15 W)博锐 英特尔酷睿 i3-7130U(双核,2.7 GHz,3 M 高速缓存,15 W) 英特尔酷睿 i5-7300U(双核,3.5 GHz,3M 高速缓存,15 W)博锐 系统 ● ● ● ● ● 操作系统 ● Microsoft Windows 10 Home ● Microsoft Windows 10 Pro 64 位 ● Ubuntu 16.
表. 3: 规格 (续) ● 14.0 英寸 HD (1366 x 768) 防眩光,高清摄像头/麦克风,WLAN/ WWAN,镁合金后盖,非触摸屏 ● 14.0 英寸 FHD (1920 x 1080) 防眩光,HD 摄像头/麦克风,支持 WLAN, 镁合金后盖,非触摸屏 ● 14.0 英寸 FHD (1920 x 1080) 防眩光,高清摄像头/麦克风,WLAN/ WWAN,镁合金后盖,非触摸屏 ● 14.0 英寸 HD (1920 x 1080) 防眩光,仅麦克风,支持 WLAN,镁合金后 盖,非触摸屏 ● 14.0 英寸 FHD (1920 x 1080) 防眩光,超低功耗面板 (SLP),高清摄像 头/麦克风,WLAN 和 ASA,窄边框镁合金后盖,非触摸屏 ● 14.0 英寸 FHD (1920 x 1080) 防眩光,超低功耗面板 (SLP),IR 摄像头/ 麦克风,WLAN 和 ASA,窄边框镁合金后盖,非触摸屏 ● 140 英寸 FHD (1920 x 1080),防眩光,高清摄像头/麦克风,WLAN/ WWAN,镁合金后盖,On-cell 触摸屏 ● 14.
表. 3: 规格 (续) ● 重量:185.00 克(0.41 磅) ● 电池容量:3.68 毫安时 60 WHr(4 芯): ● ● ● ● ● 长度:95.9 毫米(3.78 英寸) 宽度:5.70 毫米(0.22 英寸) 高度:18.50 毫米(0.71 英寸) 重量:270.00 克(0.6 磅) 电池容量:7.89 毫安时 60 WHr 长寿命电池(聚合物): ● ● ● ● ● 最大运行时配置 长度:95.9 毫米(3.78 英寸) 宽度:5.70 毫米(0.22 英寸) 高度:18.50 毫米(0.71 英寸) 重量:270.00 克(0.6 磅) 电池容量:7.
表. 3: 规格 (续) ● 可选的智能卡 ● Noble 锁 wedge 插槽 ● DC-in 摄像头 ● ● ● ● 触摸板 显示区域 ● ● ● ● 类型:高清定焦 传感器类型:CMOS 传感器技术 映像率:每秒最多 30 帧 视频分辨率:1280 x 720 像素 (0.92 MP) X 轴 — 99.50 毫米 Y 轴 — 53.0 毫米 X/Y 位置分辨率 — X:1048cpi;Y:984cpi 多点触控 — 可配置单手指和多手指手势 内部键盘 ● 14.1 英寸单指点,非背景光 ● 14.1 英寸双指点,背景光 物理规格 ● ● ● ● 环境规格 温度规格 正面到背面高度(非触摸屏):0.69 至 0.70 英寸;7.47 到 17.9 宽度:13.03 英寸;331.0 毫米 厚度:8.70 英寸;220.9 毫米 起始重量:1.4 千克;3.
表. 4: 14.0 英寸 (16:9) AG HD (1366 x 768) WLED 200 尼特(类型)eDP 1.2,高清摄像头/麦克风,支持 WLAN,镁 合金后盖,非触摸屏 (续) 响应时间(最大值) 25 毫秒上升/下降 刷新率 60 Hz 水平查看角度(最小值) +/- 40 度 垂直查看角度(最小值) +10/-30 度 像素点距 0.2265 毫米 功耗(最大值) 2.8 W 表. 5: 14.0 英寸 (16:9) AG HD (1366 x 768) WLED 200 尼特(类型)eDP 1.2,HHD 摄像头/麦克风,支持 WLAN, 镁合金后盖,非触摸屏 功能 规格 类型 高清防眩光 亮度(典型值) 200 尼特 尺寸(有效区域) ● 高度:173.95 毫米(最大值) ● 宽度:309.4 毫米(最大值) ● 对角线:14.0 英寸 Native Resolution 1366 x 768 百万像素 1.
表. 6: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,高清摄像头/麦克风,支持 WLAN, 镁合金后盖,非触摸屏 (续) 水平查看角度(最小值) +/- 80 度 垂直查看角度(最小值) +/- 80 度 像素点距 0.161 x 0.161 毫米 功耗(最大值) 3.8 瓦 表. 7: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,高清摄像头/麦克风,WWAN/ WLAN,镁合金后盖,非触摸屏 功能 规格 类型 全高清防眩光 亮度(典型值) 300 尼特 尺寸(有效区域) ● 高度:173.95 毫米(最大值),不含金属卡舌的毫米值 ● 宽度:309.4 毫米(最大值) ● 对角线:14.0 英寸 Native Resolution 1920 x 1080 百万像素 2.
表. 8: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,仅麦克风,支持 WLAN,镁合金后 盖,非触摸屏 (续) 像素点距 0.161 x 0.161 毫米 功耗(最大值) 3.8 瓦 表. 9: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,超低功耗面板 (SLP),高清摄像头/ 麦克风,WWAN 和 ASA,窄边框镁合金后盖,非触摸屏 功能 规格 类型 全高清防眩光 亮度(典型值) 300 尼特 尺寸(有效区域) ● 高度:173.95 毫米(最大值),不含金属卡舌 ● 宽度:309.4 毫米(最大值) ● 对角线:14.0 英寸 Native Resolution 1920 x 1080 百万像素 2.
表. 11: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,高清摄像头/麦克风,WWAN/ WLAN,镁合金后盖,On-cell 触摸屏 功能 规格 类型 全高清防眩光 亮度(典型值) 300 尼特 尺寸(有效区域) ● 高度:173.95 毫米(最大值) ● 宽度:309.4 毫米(最大值) ● 对角线:14.0 英寸 Native Resolution 1920 x 1080 百万像素 2.07 每英寸像素 (PPI) 157 对比度(最小值) 600:1 响应时间(最大值) 35 毫秒黑色到白色 刷新率 60 Hz 水平查看角度(最小值) +/- 80 度 垂直查看角度(最小值) +/- 80 度 像素点距 0.161 x 0.161 毫米 功耗(最大值) 4.1 W 表. 12: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.
表. 13: 14.0 英寸 (16:9) AG FHD (1920 x 1080) 300 尼特,eDP 1.3 和 PSR,IPS,IR 摄像头/麦克风,WLAN 和 ASA,窄边框镁合金后盖,On-cell 触摸屏 (续) 亮度(典型值) 300 尼特 尺寸(有效区域) ● 高度:173.95 毫米(最大值) ● 宽度:309.4 毫米(最大值) ● 对角线:14.0 英寸 Native Resolution 1920 x 1080 百万像素 2.07 每英寸像素 (PPI) 157 对比度(最小值) 600:1 响应时间(最大值) 35 毫秒黑色到白色 刷新率 60 Hz 水平查看角度(最小值) +/- 80 度 垂直查看角度(最小值) +/- 80 度 像素点距 0.161 x 0.161 毫米 功耗(最大值) 4.1 W 热键组合 表.
5 系统设置程序 借助系统设置程序,可以管理笔记本硬件并指定 BIOS 级选项。通过 System Setup(系统设置),您可以: ● ● ● ● ● 在添加或删除硬件后更改 NVRAM 设置 查看系统硬件配置 启用或禁用集成设备 设置性能和电源管理阈值 管理计算机安全保护 主题: • • • • • • • • • • • • • • • • • • • 引导菜单 导航键 系统设置选项 常规屏幕选项 系统配置屏幕选项 视频屏幕选项 安全性屏幕选项 安全引导屏幕选项 Intel Software Guard Extensions 屏幕选项 性能屏幕选项 电源管理屏幕选项 POST 行为屏幕选项 Manageability(可管理性) 虚拟化支持屏幕选项 无线屏幕选项 维护屏幕选项 系统日志屏幕选项 管理员和系统密码 在 Windows 中更新 BIOS 引导菜单 出现 Dell™ 徽标时按下 以启动一次性引导菜单,其中包含系统的有效引导设备的列表。此菜单中还包含诊断程序和 BIOS 设置 程序选项。引导菜单中列出的设备取决于系统中的可引导设备。当您尝试引导至特定设备或调出系统的诊断程序时
导航键 注: 对于大多数系统设置程序选项,您所做的任何更改都将被记录下来,但要等到重新启动系统后才能生效。 键 导航 上箭头键 移至上一字段。 下箭头键 移至下一字段。 Enter 在所选字段(如适用)中选择值或单击字段中的链接。 空格键 展开或折叠下拉列表(如适用)。 选项卡 移到下一个目标区域。 注: 仅适用于标准图形浏览器。 Esc 键 移至上一页直到显示主屏幕。在主屏幕中按 Esc 会显示一条消息,提示您保存所有未保存的更改并重新启动 系统。 系统设置选项 注: 根据笔记本电脑及其安装的设备,本部分列出的项目不一定会出现。 常规屏幕选项 此部分列出了计算机的主要硬件特性。 选项 说明 系统信息 此部分列出了计算机的主要硬件特性。 ● System Information(系统信息):显示 BIOS Version(BIOS 版本)、Service Tag(服务标签)、Asset Tag(资产标签)、Ownership Tag(所有权标签)、Ownership Date(所有权日期)、Manufacture Date (生产日期)、Express Service
选项 说明 ● CD/DVD/CD-RW Drive(CD/DVD/CD-RW 驱动器) ● Onboard NIC(机载 NIC) UEFI Boot option(UEFI 引导选项) ● Windows Boot Manager(Windows 引导管理器)(默认) Boot List Options(引导列表选项) ● Legacy(传统) ● UEFI — 默认已选择 Advanced Boot Options 此选项允许您加载传统选项 ROM。默认情况下,Enable Legacy Option ROMs(启用传统选项 ROM)已禁 用。Enable Attempt Legacy Boot(启用尝试传统引导)默认已禁用。 UEFI Boot Path Security(UEFI 引 导路径安全性) ● Always, except internal HDD(始终,内部 HDD 除外) ● Always(始终) ● Never(从不) Date/Time 允许您更改日期和时间。 系统配置屏幕选项 选项 说明 Integrated NIC 允许您配置集成的网络控制器。选项包括:
选项 说明 Thunderbolt 适配 器配置 ● ● ● ● ● ● ● USB PowerShare 此字段可配置 USB PowerShare 功能的行为。此选项允许您使用存储的系统电池电源通过 USB PowerShare 端 口为外部设备充电。此选项在默认设置下已禁用。 音频 该字段启用或禁用集成音频控制器。默认情况下,将选中 Enable Audio(启用音频)选项。选项包括: Enable Thunderbolt Technology Support(启用 Thunderbolt 技术支持)- 此选项默认已启用。 Enable Thunderbolt Adaptor Boot Support(启用 Thunderbolt 适配器引导支持) Enable Thunderbolt Adaptor Pre-boot Modules(启用 Thunderbolt 适配器预引导模块) Security level — No Security(安全级别 — 无安全) Security level—User Authorization(安全级别 — 用户授权)。此选项默认已启用。 Secur
视频屏幕选项 选项 说明 LCD Brightness 允许您根据电源(On Battery [使用电池] 和 On AC [使用交流电])设置显示屏亮度。LCD 的亮度与电池和交 流适配器无关。它可以使用滑块设置。 注: 仅当系统安装了视频卡后,才能看到视频设置。 安全性屏幕选项 选项 说明 Admin Password 允许您设置、更改或删除管理员 (admin) 密码。 注: 在设置系统或硬盘驱动器密码之前,您必须先设置管理员密码。删除管理员密码也会自动删除系统密 码和硬盘驱动器密码。 注: 密码更改成功后会立即生效。 默认设置:Not set(未设置) System Password 允许您设置、更改或删除系统密码。 注: 密码更改成功后会立即生效。 默认设置:Not set(未设置) Strong Password 允许您将此选项强制设置为一律设置增强密码。 默认设置:未选择 Enable Strong Password(启用增强密码)。 注: 如果启用强密码,管理员密码和系统密码中都必须至少包含一个大写字母、一个小写字母且必须至少 包含 8 个字符。 Password C
选项 说明 ● ● ● ● ● ● PPI Bypass for Disabled Commands(PI 绕过已禁用命令) Attestation Enable(证明启用)— 默认已启用 Key Storage Enable(密钥存储启用)— 默认已启用 SHA-256 — 默认已启用 Disabled(已禁用) Enabled(已启用)— 默认已启用 注: 要升级或降级 TPM 2.
选项 说明 ● ● ● ● ● ● Save to File(保存到文件)— 将密钥保存到用户选择的文件 Replace from File(从文件替换)— 使用用户选择的文件中的密钥替换当前密钥 Append from File(从文件附加)— 从用户选择的文件将密钥添加到当前数据库 Delete(删除)— 删除选择的密钥 Reset All Keys(重设所有密钥)— 重设为默认设置 Delete All Key(删除所有密钥)— 删除所有密钥 注: 如果禁用 Custom Mode(自定义模式),所有更改都会被删除,并且密钥会恢复为默认设置。 Intel Software Guard Extensions 屏幕选项 选项 说明 Intel SGX Enable 该字段允许您为在主操作系统环境中运行代码/存储敏感信息提供安全的环境。选项包括: ● Disabled(已禁用) ● Enabled(已启用) ● Software controlled(软件控制) 默认设置:Software controlled(软件控制) Enclave Memory Size 该选项设置 SGX Encla
电源管理屏幕选项 选项 说明 AC Behavior 允许您在已连接交流适配器时启用或禁用自动开机的功能。 默认设置:Wake on AC(唤醒 AC)未选定。 Enable Intel Speed 此选项用于启用或禁用 Intel speed shift 技术。 Shift Technology 默认设置:“Enable Intel Speed Shift Technology”(启用 Intel Speed Shift Technology)已启用。 Auto On Time 允许您设置计算机必须自动开机的时间。选项包括: ● ● ● ● Disabled(已禁用) Every Day(每天) Weekdays(工作日) Select Days(选择天数) 默认设置:Disabled(已禁用)。 USB Wake Support 允许您启用 USB 设备将系统从待机状态唤醒。 注: 此功能仅在连接交流电源适配器的情况下可用。如果交流电源适配器在待机过程中被卸下,则系统设 置程序会断开所有 USB 端口的电源,以节省电池电源。 ● Enable USB Wake Support(启用 USB
选项 说明 Primary Battery Charge Configuration 允许您选择电池的充电模式。选项包括: ● Adaptive(自适应)— 默认已启用 ● Standard(标准)— 以标准速度对电池充分充电。 ● ExpressCharge(快速充电)— 电池使用 Dell 的快速充电技术在较短的一段时间内完成充电。此选项在默 认设置下已启用 ● Primarily AC use(主交流电使用) ● 自定义 如果选择 Custom Charge(自定义充电),您还可以配置 Custom Charge Start(自定义充电启动)和 Custom Charge Stop(自定义充电停止)。 注: 并非所有充电模式都适用于所有电池。要启用该选项,请禁用 Advanced Battery Charge Configuration(高级电池充电配置)选项。 睡眠模式 ● OS Automatic selection(操作系统自动选择)— 默认已启用 Force S3(强制 S3) Type-C connector ● 7.5 Watts(7.
选项 说明 Full Screen Logo (全屏徽标) ● Enable Full Screen Logo(启用全屏徽标)— 未启用 Warnings and errors(警告和错 误) ● Prompt on warnings and errors(出现警告和错误时提示)— 默认已启用 ● 继续显示警告 ● Continue on warnings and errors(出现警告和错误时继续) Manageability(可管理性) 选项 说明 USB provision Enable USB provision(启用 USB 配置)默认未选择 MEBX Hotkey (MEBX 热键)— 默认已启用 允许您指定是否在系统引导期间启用 MEBx 热键功能。 ● Disabled(已禁用) ● Enabled(已启用) 默认设置:Enabled(已启用) 虚拟化支持屏幕选项 选项 说明 Virtualization 此字段指定虚拟机监控程序 (VMM) 是否可以使用 Intel Virtualization 技术所提供的附加硬件功能。 Enable Intel Virtua
注: 在外包装或 WWAN 卡上可以找到 WWAN 的 IMEI 编号。 维护屏幕选项 选项 说明 Service Tag 显示计算机的服务标签。 Asset Tag 允许您在尚未设置资产标签时创建系统资产标签。此选项默认未设置。 BIOS Downgrade 此字段控制将系统固件刷新为以前的修订版本。选项“Allow BIOS downgrade”(允许 BIOS 降级)默认已启 用。 Data Wipe 此字段允许用户安全地擦除所有内部存储设备中的数据。选项“Wipe on Next boot”(下次引导时擦除)默 认未启用。以下是受影响的设备列表: ● ● ● ● BIOS Recovery (BIOS 恢复) 内部 SATA HDD/SSD 内部 M.2 SATA SDD 内部 M.
1. 在系统 BIOS 或系统设置屏幕中,选择安全并按 Enter 键。 系统将显示安全屏幕。 2. 选择系统/管理员密码并在输入新密码字段中创建密码。 采用以下原则设定系统密码: ● ● ● ● 一个密码最多可包含 32 个字符。 密码可包含数字 0 至 9。 仅小写字母有效,不允许使用大写字母。 只允许使用以下特殊字符:空格、(”)、(+)、(,)、(-)、(.)、(/)、(;)、([)、(\)、(])、(`)。 3. 键入先前在确认新密码字段中输入的系统密码,然后单击确定。 4. 按 Esc 将出现一条消息,提示您保存更改。 5. 按 Y 保存更改。 计算机将重新引导。 删除或更改现有的系统设置密码 在尝试删除或更改现有系统密码和设置密码之前,确保“密码状态”为“已锁定”(在系统设置中)。如果,“密码状态”为“已 锁定”,则不能删除或更改现有系统密码或设置密码。 要进入系统设置程序,请在开机或重新引导后立即按 F2。 1. 在系统设置 BIOS 或系统设置屏幕中,选择系统安全保护并按 Enter 键。 将会显示系统安全保护屏幕。 2. 在系统安全保护屏幕中,验证密码状态为已解锁。 3.
屏幕上将显示文件下载窗口。 11. 单击保存,将文件保存到计算机中。 12. 单击运行,将更新的 BIOS 设置安装到计算机上。 请遵循屏幕上的说明操作。 在已启用 BitLocker 的系统上更新 BIOS 小心: 如果在更新 BIOS 之前未暂挂 Bitlocker,则在下一次重新引导系统时,它将不会识别 BitLocker 密钥。然后,系统将提示 您输入恢复密钥以继续,并且系统将在每次重新引导都要求提供密钥。如果恢复密钥未知,这可能会导致数据丢失或不必要的操 作系统重新安装。有关此主题的详细信息,请参阅知识库文章:在已启用 BitLocker 的戴尔系统上更新 BIOS 使用 USB 闪存盘更新您的系统 BIOS 如果系统无法加载到 Windows 但仍需要更新 BIOS,则使用其他系统下载 BIOS 文件并将其保存到可引导的 USB 闪存盘。 注: 您将需要使用可引导的 USB 闪存盘。请参阅以下文章,了解如何使用戴尔诊断部署程序包 (DDDP) 创建可引导 USB 闪存盘 的更多详细信息 1. 将 BIOS 更新 .EXE 文件下载到另一个系统。 2. 将文件(示例:O9010A12.
从 F12 一次性引导菜单快擦写 BIOS 使用复制到 FAT32 USB 闪存盘的 BIOS 更新 .
4. 选择外部 USB 设备 5.
6. 单击 Update BIOS(更新 BIOS),然后系统将重新引导以刷新 BIOS。 7.
6 软件 本章详细介绍支持的操作系统和驱动程序安装说明。 主题: 支持的操作系统 下载 Windows 驱动程序 芯片组驱动程序 视频驱动程序 音频驱动程序 网络驱动程序 USB 驱动程序 存储驱动程序 其他驱动程序 • • • • • • • • • 支持的操作系统 该主题列出了 系统支持的操作系统。 表. 15: 支持的操作系统 支持的操作系统 说明 Windows 10 ● Microsoft Windows 10 Pro 64 位 ● Microsoft Windows 10 家庭版 64 位 其它 ● Ubuntu 16.04 LTS SP1 64 位 ● NeoKylin v6.0 64 位(中国) 下载 Windows 驱动程序 1. 打开笔记本电脑。 2. 访问 Dell.com/support。 3. 单击产品支持,输入您的笔记本电脑的服务标签,然后单击提交。 注: 如果您没有服务标签,请使用自动检测功能,或者手动浏览找到您的笔记本电脑的型号。 4. 单击驱动程序和下载。 5. 选择您的笔记本电脑上安装的操作系统。 6. 向下滚动页面并选择要安装的驱动程序。 7.
软件 79
视频驱动程序 验证是否系统中已安装视频驱动程序。 音频驱动程序 验证系统中是否已安装音频驱动程序。 80 软件
网络驱动程序 系统配有 LAN 和 WiFi 驱动程序并能够检测到 LAN 和 WiFi,而不必通过安装驱动程序。 USB 驱动程序 验证系统中是否已安装 USB 驱动程序。 存储驱动程序 验证系统中是否已安装存储控制器驱动程序。 其他驱动程序 本节列出了适用于设备管理器中所有其他组件的驱动程序详情。 安全保护设备驱动程序 验证系统中是否已安装安全保护设备驱动程序。 软件 81
HID 验证系统中是否已安装 HID 驱动程序。 Control Vault 设备 验证系统中是否已安装 control vault 设备驱动程序。 近接设备 验证系统中是否已安装近接设备驱动程序。 智能卡读取器 验证系统中是否已安装智能卡读取器驱动程序。 生物信息设备 验证系统中是否已安装生物信息设备驱动程序 映像设备驱动程序 验证系统中是否已安装映像设备驱动程序。 82 软件
软件 83
7 故障排除 主题: • • 戴尔增强型启动前系统评估 — ePSA Diagnostic 3.0 实时时钟重置 戴尔增强型启动前系统评估 — ePSA Diagnostic 3.
8 联系戴尔 注: 如果您不能连接至 Internet,您可以在您的购买发票、装箱单、账单或戴尔产品目录中找到联系信息。 戴尔提供多种联机和基于电话的支持和服务选项。具体的服务随您所在国家/地区以及产品的不同而不同,某些服务在您所在的地区 可能不提供。如要联系戴尔解决有关销售、技术支持或客户服务问题: 1. 访问 Dell.com/support。 2. 选择您的支持类别。 3. 在页面底部的选择国家/地区下拉列表中,确认您所在的国家或地区。 4.