Dell Latitude C610/C510 Service Manual Dell™ Latitude™ C610/C510 Service Manual Before You Begin System Components Hard Drive Memory Modules, Mini PCI Card, and Modem Keyboard Display Assembly, Display Latch, and Hinge Covers Palm Rest Microprocessor Thermal Cooling Assembly Microprocessor Module Hybrid Cooling Fan Reserve Battery Flashing the BIOS Speaker Assemblies System Board Battery and Module Bay Latches Pin Assignments for I/O Connectors Notes, Notices, and Cautions NOTE: A NOTE indicates important
Before You Begin: Dell Latitude C610/C510 Service Manual Back to Contents Page Before You Begin Dell™ Latitude™ C610/C510 Service Manual Preparing to Work Inside the Computer Recommended Tools Screw Identification Preparing to Work Inside the Computer CAUTION: Before working inside your computer, read "Safety and EMC Instructions: Portable Computers" in your System Information Guide. NOTICE: Only a certified service technician should perform repairs on your computer.
Before You Begin: Dell Latitude C610/C510 Service Manual The procedures in this manual require the following tools: #1 magnetized Phillips screwdriver ¼-inch flat-blade screwdriver Small plastic scribe Microprocessor extractor Flash BIOS update program floppy disk or CD Computer Orientation 1 back 2 right 3 front 4 left Screw Identification When you are removing and replacing components, photocopy the placemat as a tool to lay out and keep track of the screws.
Before You Begin: Dell Latitude C610/C510 Service Manual NOTICE: When reinstalling a screw, you must use a screw of the correct diameter and length. Make sure that the screw is properly aligned with its corresponding hole, and avoid over tightening.
Before You Begin: Dell Latitude C610/C510 Service Manual System Board to Bottom Case: (10 each) Modem to System Board: (2 each) Display Latch: Memory Module Cover: (2 each) (2 each) (2 captive screws) (1 each) NOTE: The single screw is one of the five keyboard screws. Back to Contents Page file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/begin.
System Components: Dell Latitude C610/C510 Service Manual Back to Contents Page System Components Dell™ Latitude™ C610/C510 Service Manual Exploded View NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this manual assumes that a part can be replaced by performing the removal procedure in reverse order.
System Components: Dell Latitude C610/C510 Service Manual 9 fan guard Back to Contents Page file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/system.
Hard Drive: Dell Latitude C610/C510 Service Manual Back to Contents Page Hard Drive Dell™ Latitude™ C610/C510 Service Manual Removing the Hard Drive Replacing the Hard Drive Removing the Hard Drive 1. Save and close any open files, exit any open programs, and shut down the computer. NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: The hard drive is very sensitive to shock.
Hard Drive: Dell Latitude C610/C510 Service Manual 4. Lift up the hard drive door until you hear a click. 5. Slide the hard drive out of the computer. Replacing the Hard Drive NOTICE: Use firm and even pressure to slide the hard drive into place. If you force the hard drive into place using excessive force, you may damage the connector. 1. Lift up the hard drive door until you hear a click. Push the hard drive into the drive bay until it is fully seated in the bay. 2. Press the hard drive door down. 3.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual Back to Contents Page Memory Modules, Mini PCI Card, and Modem Dell™ Latitude™ C610/C510 Service Manual Memory Modules Mini PCI Card Modem Memory Modules Removing the Memory Module Cover NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual Removing the Memory Modules NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1. Remove the memory module cover.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual 1. If you only have one memory module, install it in the connector labeled "JDIM1" on the system board. Install a second memory module in the connector labeled "JDIM2." NOTE: Memory modules are keyed, or designed to fit into their sockets, in only one direction. NOTICE: The memory module must be inserted at a 45-degree angle to avoid damaging the connector. 2.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual 1 antenna connectors on card (2) 2 antenna cables (2) Replacing the Mini PCI Card 1. Align the Mini PCI card with the socket at a 45-degree angle, and press the Mini PCI card into the socket. NOTICE: The connectors are keyed for correct insertion; do not force the connections. 2. Lower the Mini PCI card toward the inner tabs to approximately a 20-degree angle. 3.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual NOTICE: Do not pull on the modem cable. Pull from the modem connector to disconnect the cable. 3. Pull straight up on the attached pull tab to lift the modem out of its connector on the system board and disconnect the modem cable. Modem Removal 1 M2 x 3-mm screws (2) 2 modem connector 3 modem cable 4 pull tab Replacing the Modem 1. Connect the modem cable to the modem.
Memory Modules, Mini PCI Card, and Modem: Dell Latitude C610/C510 Service Manual file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/upgrades.
Keyboard: Dell Latitude C610/C510 Service Manual Back to Contents Page Keyboard Dell™ Latitude™ C610/C510 Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Keyboard: Dell Latitude C610/C510 Service Manual b. Lift the center control cover up and away from the bottom case. Center Control Cover Removal 5. To release the keyboard from the palm rest, use a small, flat-blade screwdriver or plastic scribe to pull up on the scalloped edge of the blank key on the keyboard. Keyboard Removal 1 keyboard 2 track stick 3 scalloped edge of blank key 4 palm rest 6. Lift the keyboard straight up until it clears the keyboard boss support in the bottom case.
Keyboard: Dell Latitude C610/C510 Service Manual 7. Rotate the keyboard forward toward the front of the computer. 8. Rest the key face of the keyboard on the palm rest. NOTICE: Do not pull on the keyboard flex and track stick cables. 9. Pull up on the keyboard connector to disconnect it from the interface connector on the system board. Keyboard Connector Removal 1 boss support (5) 2 track stick cable 3 keyboard flex cable 4 keyboard connector 5 orientation label 10.
Keyboard: Dell Latitude C610/C510 Service Manual snap the right side of the keyboard into place. NOTICE: Position the keyboard flex and track stick cables so that they are not pinched when you replace the keyboard in the bottom case. 4. Check that the keyboard is correctly installed. The keys should be flush with the left and right surfaces of the palm rest. 5. Replace the center control cover, close the display assembly, and turn the computer over. 6. Reinstall the five M2.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual Back to Contents Page Display Assembly, Display Latch, and Hinge Covers Dell™ Latitude™ C610/C510 Service Manual Display Assembly Display Latch Hinge Covers Display Assembly NOTICE: You must remove the display assembly before you remove the palm rest. NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual 1 M2 x 3-mm screws (4) 2 top cover 3 center control cover 4 M2.5 x 5-mm screws (5) 5 bottom case 6 EMI shield bracket 1. Remove the hard drive. 2. Remove the center control cover. 3. Remove the keyboard. 4. Close the display. 5. From the back of the computer, remove the five M2.5 x 5-mm screws labeled "circle D." 6.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual 1 M2 x 3-mm screws (2) 9. Pull up on the pull tab that is attached to the display-feed flex cable connector to remove it from the interface connector on the system board. 10. Lift the display assembly up and out of the bottom case. 14.1-Inch Display Bezel and Panel 1 rubber screw covers (6) 5 M2 x 4-mm screws (5) 2 M2.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1. Remove the hard drive. 2. Remove the display assembly. 3. Use a plastic scribe to pry the six rubber screw covers out of the screw holes located on the front of the bezel. 4.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual 1 display panel connector 2 top flex cable connector 3 pull tab 4 bottom flex cable connector 5 inverter connector 9. Remove the tape that secures the display panel connector and the tape that secures the middle of the display-feed flex cable to the display panel. 10. Pull the top flex cable connector down and away to remove it from the display panel connector. Replacing the 14.1-Inch Display Panel 1.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual Display Latch NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. Removing the Display Latch 1. Remove the hard drive. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the two M2.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual On 14.1-inch SXGA+ panels, align the screw holes and place the display latch and attached bracket in the top cover. 2. Replace the two M2.5 x 5-mm screws and the two M1.7 x 3.5-mm screws that secure the display latch and bracket to the top cover. Hinge Covers Removing the Hinge Covers 1. Remove the display assembly. 2.
Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual 1 right hinge cover 2 left hinge cover Back to Contents Page file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/display.
Palm Rest: Dell Latitude C610/C510 Service Manual Back to Contents Page Palm Rest Dell™ Latitude™ C610/C510 Service Manual Removing the Palm Rest Removing the Palm Rest NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Palm Rest: Dell Latitude C610/C510 Service Manual 1 M2.5 x 12-mm screws (3) 2 M2 x 3-mm screws (2) 3 hard-drive bay door 5. Remove the two M2 x 3-mm screws that are located in the hard-drive bay door labeled "circle P." 6. Turn the computer over, and remove the three M2 x 3-mm screws that secure the palm rest to the bottom case. a. Remove the two M2 x 3-mm screws that are located on the back edge of the bottom case, underneath the display assembly. b.
Palm Rest: Dell Latitude C610/C510 Service Manual 8. Starting at the back center of the palm rest, use your fingers to separate the palm rest from the bottom case by lifting up the inside of the palm rest while pushing in on the outside. Back to Contents Page file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/palmrest.
Microprocessor Thermal Cooling Assembly: Dell Latitude C610/C510 Service Manual Back to Contents Page Microprocessor Thermal Cooling Assembly Dell™ Latitude™ C610/C510 Service Manual Removing the Microprocessor Thermal Cooling Assembly Replacing the Microprocessor Thermal Cooling Assembly Removing the Microprocessor Thermal Cooling Assembly NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.
Microprocessor Thermal Cooling Assembly: Dell Latitude C610/C510 Service Manual 3 right side 4. Lift the microprocessor thermal cooling assembly up and out of the system board. Replacing the Microprocessor Thermal Cooling Assembly 1. Place the right side of the microprocessor thermal cooling assembly under the palm rest and lower the assembly onto the system board. 2. Tighten the four captive screws, labeled 1 through 4, in consecutive order.
Microprocessor Module: Dell Latitude C610/C510 Service Manual Back to Contents Page Microprocessor Module Dell™ Latitude™ C610/C510 Service Manual Removing the Microprocessor Module Replacing the Microprocessor Module Removing the Microprocessor Module NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Microprocessor Module: Dell Latitude C610/C510 Service Manual NOTICE: To ensure maximum cooling for the microprocessor, do not touch the heat transfer areas on the microprocessor thermal cooling assembly. The oils in your skin reduce the heat transfer capability of the thermal pads. 3. Remove the microprocessor thermal cooling assembly. NOTICE: When removing the microprocessor module, pull the module straight up. Be careful not to bend the pins on the microprocessor module. 4.
Hybrid Cooling Fan: Dell Latitude C610/C510 Service Manual Back to Contents Page Hybrid Cooling Fan Dell™ Latitude™ C610/C510 Service Manual Removing the Hybrid Cooling Fan Removing the Hybrid Cooling Fan NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Hybrid Cooling Fan: Dell Latitude C610/C510 Service Manual 1 system-board interface connector 5 M2 x 3-mm screw (1) 2 fan power cable 6 M2.5 x 5-mm screws (2) 3 spring fingers 7 hybrid cooling fan 4 keyboard screw hole 7. Disconnect the fan power cable from the system-board interface connector and remove the hybrid cooling fan. NOTE: The fan power cable is long, and can be pulled out from under the EMI shield to provide access to the connector.
Reserve Battery: Dell Latitude C610/C510 Service Manual Back to Contents Page Reserve Battery Dell™ Latitude™ C610/C510 Service Manual Removing the Reserve Battery Replacing the Reserve Battery Removing the Reserve Battery NOTICE: The reserve battery provides power to the computer's RTC and NVRAM when the computer is turned off. Removing the battery causes the computer to lose the date and time information as well as all user-specified parameters in the BIOS.
Reserve Battery: Dell Latitude C610/C510 Service Manual 3 system board connector 4 reserve battery cable Replacing the Reserve Battery 1. Connect the reserve battery cable to the system board connector. 2. Position the reserve battery above the speaker connector on the system board. 3. Update the BIOS using a flash BIOS update program floppy disk or CD. For instructions on how to flash the BIOS, see "Flashing the BIOS.
Flashing the BIOS: Dell Latitude C610/C510 Service Manual Back to Contents Page Flashing the BIOS Dell™ Latitude™ C610/C510 Service Manual Flashing the BIOS Flashing the BIOS To update the basic input/output system (BIOS): 1. Make sure that the AC adapter is plugged in and that the main battery is installed properly. 2. Turn on the computer. The following error message appears: System hardware failures: #0010 Strike the F1 key to shutdown 3.
Speaker Assemblies: Dell Latitude C610/C510 Service Manual Back to Contents Page Speaker Assemblies Dell™ Latitude™ C610/C510 Service Manual Removing the Speaker Assemblies Replacing the Speaker Assemblies Removing the Speaker Assemblies NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Speaker Assemblies: Dell Latitude C610/C510 Service Manual 1 right speaker 2 palm-rest screw post 3 bottom case holders (2) 4 left speaker Speaker Assemblies file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/speakers.
Speaker Assemblies: Dell Latitude C610/C510 Service Manual 1 antenna cable 6 antenna cable 2 in-line connector 7 right speaker holder 3 left speaker 8 mounting ring 4 mounting ring 9 right speaker 5 left speaker holder 1. Remove the hard drive. 2. Remove the keyboard. 3. Remove the display assembly. 4. Remove the palm rest. 5. Disconnect the speaker interface cable connectors. file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/speakers.
Speaker Assemblies: Dell Latitude C610/C510 Service Manual NOTICE: Do not pull the antenna wire when removing the speaker (see "Speaker Orientation"). NOTICE: Handle the speaker assemblies and speakers with care to avoid damaging the speaker cones. 6. Remove the speaker assemblies by pulling them straight up and out of the bottom case. NOTE: The left speaker has an in-line connector, and its antenna cable is longer than the antenna cable of the right speaker. Replacing the Speaker Assemblies 1.
System Board: Dell Latitude C610/C510 Service Manual Back to Contents Page System Board Dell™ Latitude™ C610/C510 Service Manual Removing the System Board Replacing the System Board Removing the System Board The system board's BIOS chip contains the service tag sequence, which is also visible on a barcode label on the bottom of the computer. The replacement kit for the system board includes a CD that provides a utility for transferring the service tag sequence to the replacement system board.
System Board: Dell Latitude C610/C510 Service Manual 1 fan guard 2 M2.5 x 5-mm screws (9) 10. Turn the computer over and remove the M2.5 x 5-mm screw, which is labeled "circle B" with an arrow on the front center of the system board by the battery connector (see "System Board Removal"). System Board Removal 1 M2.5 x. 5-mm screw (1) file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/sysboard.
System Board: Dell Latitude C610/C510 Service Manual 11. Remove the speakers from the bottom case. 12. Pull the right side of the bottom case, next to the external headphone and microphone connectors, away from the system board as you simultaneously lift the front of the system board out and away from the bottom case. Replacing the System Board 1. Install the microprocessor on the replacement system board. 2. Connect the right and left speakers to the replacement system board. 3.
Battery and Module Bay Latches: Dell Latitude C610/C510 Service Manual Back to Contents Page Battery and Module Bay Latches Dell™ Latitude™ C610/C510 Service Manual Removing the Battery and Module Bay Latches Replacing the Battery and Module Bay Latches Removing the Battery and Module Bay Latches NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.
Battery and Module Bay Latches: Dell Latitude C610/C510 Service Manual 1 bumps (2 per latch) 5 latch buttons (2) 2 slider 6 snap tabs (2 per latch button) 3 spring 7 wear rib 4 bottom case Replacing the Battery and Module Bay Latches 1. Snap in the new latch button from behind the bottom case, making certain that the snap tabs are fully engaged in the latch. To prevent the latch assembly from coming loose, apply pressure to the latch and spring while replacing the latch button. 2.
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual Back to Contents Page Pin Assignments for I/O Connectors Dell™ Latitude™ C610/C510 Service Manual USB Connector Pin Signal 1 VCC 2 -Data 3 +Data 4 Ground Serial Connector Pin Signal Pin Signal 1 DCD 6 DSR 2 RXDA 7 RTS 3 TXDA 8 CTS 4 DTR 9 RI 5 GND file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual Parallel Connector Pin Signal Pin Signal 1 STRB#/5V 11 BUSY/MTR# 2 PD0/INDEX# 12 PE/WDATA# 3 PD1/TRK0# 13 SLCT/WGATE# 4 PD2/WP# 14 AFDF# 5 PD3/RDATA# 15 ERROR#HDSEL# 6 PD4/DSKCHG# 16 INIT#/DIR# 7 PD5F 17 SLCT_IN#STEP# 8 PD6F 18-23 GND 9 PD7F 24 DFDD/LPT# 10 ACK#/DRV# 25 GND Video Connector Pin Signal Pin Signal 1 RED 9 CRT_VCC 2 GREEN 10 GND 3 BLUE 11 MSEN# 4 NC 12 DAT_DDC2 5
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual 6 GND 14 VSYNC 7 GND 15 CLK_DDC2 8 GND PS/2 Connector Pin Signal 1 DAT_KBD 2 DAT_SM1 3 GND 4 PS2VCC 5 CLK_KBD 6 CLK_SM1 S-Video TV-Out Connector S-Video Pin Signal 1 GND 2 GND 3 DLUMA-L file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual 4 DCRMA-L Composite Video Pin Signal 5 NC 6 DCMPS-L 7 GND Docking Connector Pin Signal Pin Signal 1 STRB#/5V 101 VGA_GRN 2 PD0 102 GND 3 PD1 103 VGA_RED 4 PD2 104 GND 5 PD3 105 VGA_BLU 6 PD4 106 DOCK_SD/MODE 7 PD5 107 D_IRTX 8 PD6 108 D_IRRX 9 PD7 109 GND 10 GND 110 SPIRQB# 11 DOCK_SPKR 111 SPIRQC# 12 DOCK_MIC 112 DAT_DDC2 13 DOCK_LINE 113 CLK_DDC2 14 DOCK_CDROM 114 SPAR 15 GND
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual 21 GND 121 GND 22 NC 122 SDEVSEL# 23 NC 123 STRDY# 24 D_ATCTLED 124 SIRDY# 25 D_PWRLED 125 SFRAME# 26 DOCK_PWR_SRC 126 SCLKRUN# 27 DOCK_PWR_SRC 127 GND 28 DOCK_PWR_SRC 128 SGNTA# 29 GND 129 SREQA# 30 +5VDOCK 130 SGNT0# 31 +5VDOCK 131 SREQ0# 32 +5VDOCK 132 SPCIRST# 33 +5VDOCK 133 SH1SEL# 34 +5VDOCK 134 GND 35 GND 135 SWRPRT# 36 DOCK_PWR_SRC 136 SDSKCHG#/DRQ 37 DOCK_PWR_SRC 137 SDIR# 38 DO
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual 61 RUN_ON# 161 GND 62 GND 162 SAD7 63 NC 163 SAD8 64 DOCK_SCLK 164 SC/BE0# 65 DOCK_LRCK 165 SAD9 66 DOCK_MCLK 166 SAD10 67 GND 167 SAD11 68 +12V 168 SAD12 69 AFD# 169 GND 70 ERROR# 170 SAD13 71 ACK# 171 SAD14 72 GND 172 SAD15 73 INIT# 173 SAD16 74 SLCT_IN# 174 SC/BE1# 75 BUSY 175 CD/BE2# 76 PE 176 GND 77 SLCT 177 SAD17 78 GND 178 SAD18 79 DAT_SMB 179 SAD19 80 DCLK_SMB 180 SAD
Pin Assignments for I/O Connectors: Dell Latitude C610/C510 Service Manual Back to Contents Page file:///C|/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/pinouts.