Dell Latitude D500 Service Manual Dell™ Latitude™ D500 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Memory Module, Mini PCI Card, and Devices Memory Module Mini PCI Card Devices System Components Reserve Battery Hard Drive Keyboard Display Assembly and Display Latch Display Assembly Display Bezel Display Panel Display Latch Palm Rest Docking Doors Fan Bluetooth™ Card Microprocessor Thermal-Cooling Assembly System Board Mic
Dell Latitude D500 Service Manual S-Video TV-Out Connector Serial Connector Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Before You Begin: Dell Latitude D500 Service Manual Back to Contents Page Before You Begin Dell™ Latitude™ D500 Service Manual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Before You Begin: Dell Latitude D500 Service Manual NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the computer operating system, press and hold the power button for 4 seconds. 4. If the computer is connected to a docking device (docked), undock it. 5. Disconnect the computer from the electrical outlet. 6. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices. 7.
Before You Begin: Dell Latitude D500 Service Manual 11. Remove any installed memory modules, Mini PCI cards, and devices, including a second battery if one is installed. 12. Remove the hard drive. Recommended Tools The procedures in this manual require the following tools: ● #1 Phillips screwdriver ● ¼-inch flat-blade screwdriver ● Small plastic scribe ● Flash BIOS update program floppy disk or CD file:///F|/Service%20Manuals/Dell/Latitude/d500/begin.
Before You Begin: Dell Latitude D500 Service Manual Computer Orientation 1 back 2 right 3 front 4 left Screw Identification When you are removing and replacing components, photocopy "Screw Identification" as a tool to lay out and keep track of the screws. The placemat provides the number of screws and their sizes. file:///F|/Service%20Manuals/Dell/Latitude/d500/begin.
Before You Begin: Dell Latitude D500 Service Manual Optional Device: Hard Drive: Keyboard: (1 each) (1 each) (2 each) Display Assembly: Display Bezel: Display Panel: (3 each) (display bumpers, 6 each) (4 each) (6 each) file:///F|/Service%20Manuals/Dell/Latitude/d500/begin.
Before You Begin: Dell Latitude D500 Service Manual Display Latch: Palm Rest: Fan: (3 each) (3 each) (2 each) (9 each) System Board: Speakers: Modem: (1 each) (1 each) (1 each) (1 each) (1 each) file:///F|/Service%20Manuals/Dell/Latitude/d500/begin.
Before You Begin: Dell Latitude D500 Service Manual (4 each) Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/begin.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual Back to Contents Page Memory Module, Mini PCI Card, and Devices Dell™ Latitude™ D500 Service Manual Memory Module Mini PCI Card Devices Memory Module CAUTION: Before working inside your Dell™ computer, read the safety instructions in your System Information Guide.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual NOTICE: To prevent damage to the memory module connector, do not use tools to spread the securing clips that secure the memory module. 3. If you are replacing a memory module, remove the existing module. NOTICE: Handle memory modules by their edges, and do not touch the components on a module. a. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "JDIM (Slot 1)" before you install a module in the connector labeled "JDIM2." 4. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of the connector. b. Slide the edge of the module firmly into the connector, and rotate the module down until you feel a click.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual 6. Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet. 7. Turn on the computer. As the computer boots, it detects the additional memory and automatically updates the system configuration information. Mini PCI Card If you ordered a Mini PCI card at the same time that you ordered your computer, Dell has already installed the card for you.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual 3. Place your finger under the cover at the indentation, lift up the cover, and slide the cover open. file:///F|/Service%20Manuals/Dell/Latitude/d500/upgrades.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual 4. If a Mini PCI card is not already installed, go to step 5. If you are replacing a Mini PCI card, remove the existing card: a. Disconnect the Mini PCI card from any attached cables. NOTICE: To prevent damage to the memory module connector, do not use tools to spread the securing clips that secure the memory module. b. Release the Mini PCI card by spreading the securing clips until the card pops up slightly. c.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual 1 antenna cables 2 antenna connectors on card (2) 7. Lower the Mini PCI card toward the inner tabs to approximately a 20-degree angle. 8. Continue lowering the Mini PCI card until it snaps into the inner tabs of the connector. 9. Replace the cover. Devices Your computer ships with an optical drive installed in the module bay. However, the device security screw is not installed in the optical drive but packaged separately.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual 1 device latch release 2. Pull the device by the latch release to remove the device from the module bay. file:///F|/Service%20Manuals/Dell/Latitude/d500/upgrades.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual If the Device Security Screw Is Installed 1. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions. NOTICE: To prevent damage to devices, place them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them. 2. Close the display and turn the computer over. 3.
Memory Module, Mini PCI Card, and Devices: Dell Latitude D500 Service Manual Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/upgrades.
System Components: Dell Latitude D500 Service Manual Back to Contents Page System Components Dell™ Latitude™ D500 Service Manual NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order.
System Components: Dell Latitude D500 Service Manual 1 display assembly 8 speakers 2 center control cover 9 hard drive 3 palm rest 10 microprocessor 4 system board 11 microprocessor thermalcooling assembly 5 computer base 12 fan 6 battery 13 keyboard 7 reserve battery 14 display cable Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/system.
Reserve Battery: Dell Latitude D500 Service Manual Back to Contents Page Reserve Battery Dell™ Latitude™ D500 Service Manual CAUTION: Before working inside your Dell™ computer, read the safety instructions in your System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1.
Reserve Battery: Dell Latitude D500 Service Manual 1 reserve battery cover 4. Pull the reserve battery straight out of the computer base. 5. Disconnect the reserve-battery cable connector from the battery connector. 1 battery connector 2 reserve battery Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/reserve.
Hard Drive: Dell Latitude D500 Service Manual Back to Contents Page Hard Drive Dell™ Latitude™ D500 Service Manual CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before working inside your computer, read the safety instructions in your System Information Guide. NOTICE: To prevent data loss, shut down your computerbefore removing the hard drive.
Hard Drive: Dell Latitude D500 Service Manual 1 M2.5 x 5-mm screw NOTICE: If you do not open the display before you remove your hard drive, you might permanently scratch your display. 3. Open the display approximately 0.5 inch. NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in your System Information Guide. 4. Slide the hard drive out of the computer. file:///F|/Service%20Manuals/Dell/Latitude/d500/hdd.
Hard Drive: Dell Latitude D500 Service Manual 5. Remove the new drive from its packaging. Save the original packaging to use when storing or shipping the hard drive. NOTICE: If you do not open the display before you replace your hard drive, you might permanently scratch your display bezel. 6. Open the display approximately 0.5 inch. NOTICE: Use firm and even pressure to slide the drive into place. If you force the hard drive into place using excessive force, you may damage the connector. 7.
Hard Drive: Dell Latitude D500 Service Manual Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/hdd.
Keyboard: Dell Latitude D500 Service Manual Back to Contents Page Keyboard Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Keyboard: Dell Latitude D500 Service Manual 1 display 2 center control cover 3 palm rest 3. Remove the center control cover: a. Open the display all the way (180 degrees) so that it lies flat against your work surface. b. Starting on the right side of the computer, use a plastic scribe to pry up the center control cover. Lift it away from the computer, and lay it aside. 1 center control cover 4. Remove the keyboard: a. Remove the two M2.5 x 6-mm screws across the top of the keyboard.
Keyboard: Dell Latitude D500 Service Manual NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and timeconsuming to replace. Be careful when removing and handling the keyboard. b. Rotate the keyboard up and slide it forward. c. Hold the keyboard up and slightly forward to allow access to the keyboard connector. d. Pull up on the keyboard connector tab to disconnect the keyboard connector from the system board. 1 M2.
Keyboard: Dell Latitude D500 Service Manual file:///F|/Service%20Manuals/Dell/Latitude/d500/keyboard.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual Back to Contents Page Display Assembly and Display Latch Dell™ Latitude™ D500 Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 1 M2.5 x 6-mm screws (3) 2 display cable connector 3 display 4 computer base 5 pull-tab 6 system board connector 7 captive screw 8 cable-routing clips (4) 5. Pull up on the pull-tab that is attached to the display cable connector to remove the connector from the system board. 6. Remove the three M2.5 x 6-mm screws. file:///F|/Service%20Manuals/Dell/Latitude/d500/display.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 7. Rotate the display assembly to a 90-degree angle, and lift the display assembly up and out of the computer base. 1 display 2 computer base file:///F|/Service%20Manuals/Dell/Latitude/d500/display.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 1 display bumpers (6) 4 display panel file:///F|/Service%20Manuals/Dell/Latitude/d500/display.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 2 M2 x 5-mm screws (6) 5 top cover 3 display bezel 6 M2 x 5-mm screws (4) Display Bezel CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 1 top flex-cable connector 2 display connector 3 pull-tab on bottom flexcable connector 4 inverter connector Display Latch NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 1. Remove the keyboard. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the three M2 x 5-mm screws that secure the display bracket to the top cover. 5. Lift the display bracket out of the top cover, and then remove the display latch. NOTE: Ensure that the display bracket is upright when you replace the display latch. 1 top cover 2 M2 x 5-mm screws (3) file:///F|/Service%20Manuals/Dell/Latitude/d500/display.
Display Assembly and Display Latch: Dell Latitude D500 Service Manual 3 display bracket 4 display latch Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/display.
Palm Rest: Dell Latitude D500 Service Manual Back to Contents Page Palm Rest Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Palm Rest: Dell Latitude D500 Service Manual 1 M2 x 3-mm screws (3) 2 top of the palm rest 5. Disconnect the touch pad connector from the system board. file:///F|/Service%20Manuals/Dell/Latitude/d500/palmrest.
Palm Rest: Dell Latitude D500 Service Manual 1 back center of the palm rest 2 touch pad connector 3 system board connector 4 computer base 6. Turn the computer over and remove the nine M2.5 x 8-mm screws. file:///F|/Service%20Manuals/Dell/Latitude/d500/palmrest.
Palm Rest: Dell Latitude D500 Service Manual 1 M2.5 x 8-mm screws (9) NOTICE: Carefully separate the palm rest from the computer base to avoid damage to the palm rest. 7. Starting at the back center of the palm rest, use your fingers to separate the palm rest from the computer base by lifting the inside of the palm rest while pushing in on the outside. NOTE: When you reinstall the palm rest, attach the right side of the palm rest first.
Docking Doors: Dell Latitude D500 Service Manual Back to Contents Page Docking Doors Dell™ Latitude™ D500 Service Manual Removing the Docking Doors CAUTION: Before working inside your computer, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1.
Docking Doors: Dell Latitude D500 Service Manual 1 docking doors Installing the Docking Doors Slide the side of the docking doors with the spring over the longer posts. 1 docking doors with spring 2 longer post Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/dockdoor.
Docking Doors: Dell Latitude D500 Service Manual file:///F|/Service%20Manuals/Dell/Latitude/d500/dockdoor.
Fan: Dell Latitude D500 Service Manual Back to Contents Page Fan Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3.
Fan: Dell Latitude D500 Service Manual 1 M2.5 x 8-mm screws (2) 2 fan 3 fan cable connector 4 system board connector 6. Remove the two M2.5 x 8-mm screws from the fan, and pull the fan away from the system board. file:///F|/Service%20Manuals/Dell/Latitude/d500/fan.
Fan: Dell Latitude D500 Service Manual Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/fan.
Bluetooth™ Card: Dell Latitude D500 Service Manual Back to Contents Page Bluetooth™ Card Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Bluetooth™ Card: Dell Latitude D500 Service Manual 1 Bluetooth card 2 system board connector Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/blue.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D500 Service Manual Back to Contents Page Microprocessor Thermal-Cooling Assembly Dell™ Latitude™ D500 Service Manual Removing the Microprocessor Thermal-Cooling Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D500 Service Manual 1 microprocessor thermalcooling assembly 2 captive screws (4) 4. Rotate the microprocessor thermal-cooling assembly up toward the side of the computer and away from the system board. Installing the Microprocessor Thermal-Cooling Assembly 1. Place the left side of the microprocessor thermal-cooling assembly under the palm rest and rotate the assembly onto the system board. 2.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D500 Service Manual Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/thermal.
System Board: Dell Latitude D500 Service Manual Back to Contents Page System Board Dell™ Latitude™ D500 Service Manual Removing the System Board CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
System Board: Dell Latitude D500 Service Manual 1 M2.5 x 4-mm screw 2 M2.5 x 8-mm screw 3 system board file:///F|/Service%20Manuals/Dell/Latitude/d500/sysboard.
System Board: Dell Latitude D500 Service Manual 1 M2 x 3-mm screws (4) 8. Remove the four M2 x 3-mm screws labeled "circle B" that secure the system board to the computer base. 9. Pull out the system board starting from the front of the computer. Installing the System Board 1. Follow all of the steps in "Removing the System Board" in reverse order. NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer.
System Board: Dell Latitude D500 Service Manual NOTE: After replacing the system board, enter the computer Service Tag into the BIOS of the replacement system board. 3. Insert the floppy disk or CD that accompanied the replacement system board into the appropriate drive. Follow the instructions that appear on the screen. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/sysboard.
Microprocessor Module: Dell Latitude D500 Service Manual Back to Contents Page Microprocessor Module Dell™ Latitude™ D500 Service Manual Removing the Microprocessor Module CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Microprocessor Module: Dell Latitude D500 Service Manual 1 screwdriver (perpendicular to microprocessor) 2 ZIF-socket cam screw 3 ZIF socket 4 pin-1 corner NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw. 5. Lift out the microprocessor module. file:///F|/Service%20Manuals/Dell/Latitude/d500/cpu.
Microprocessor Module: Dell Latitude D500 Service Manual Installing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force. NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket. 1.
Flashing the BIOS: Dell Latitude D500 Service Manual Back to Contents Page Flashing the BIOS Dell™ Latitude™ D500 Service Manual 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. NOTE: If you use a BIOS update program CD to flash the BIOS, set up the computer to boot from a CD before inserting the CD. 2. Insert the BIOS update program floppy disk or CD, and turn on the computer. Follow the instructions that appear on the screen.
Speakers: Dell Latitude D500 Service Manual Back to Contents Page Speakers Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard.
Speakers: Dell Latitude D500 Service Manual 1 speaker 5 M2.5 x 4-mm screw 2 speaker connector 6 computer base 3 system board connector 7 M2.5 x 8-mm screw 4 reserve battery Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/speakers.
Base Latch: Dell Latitude D500 Service Manual Back to Contents Page Base Latch Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Base Latch: Dell Latitude D500 Service Manual 1 base latch 2 computer base Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/latch.
Modem: Dell Latitude D500 Service Manual Back to Contents Page Modem Dell™ Latitude™ D500 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3.
Modem: Dell Latitude D500 Service Manual 1 modem 4 system board connector 2 pull-tab 5 modem cable 3 M2 x 3-mm screw 6. Disconnect the modem cable from the modem. NOTICE: Do not disconnect the modem cable from the system board. 7. Pull up on the pull-tab to disconnect the modem from the system board connector. NOTICE: Ensure that the modem cable is routed correctly when you replace the modem. file:///F|/Service%20Manuals/Dell/Latitude/d500/modem.
Modem: Dell Latitude D500 Service Manual 1 modem 2 modem cable Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/modem.
Pin Assignments for I/O Connectors: Dell Latitude D500 Service Manual Back to Contents Page Pin Assignments for I/O Connectors Dell™ Latitude™ D500 Service Manual USB Connector Video Connector Parallel Connector S-Video TV-Out Connector Serial Connector USB Connector Pin Signal 1 USB5V+ 2 USBP– 3 USBP+ 4 GND file:///F|/Service%20Manuals/Dell/Latitude/d500/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D500 Service Manual Video Connector Pin Signal Pin Signal 1 CRT_R 9 5V+ 2 CRT_G 10 GND 3 CRT_B 11 MONITOR_DETECT– 4 NC 12 DDC_DATA 5 GND 13 CRT_HS 6 GND 14 CRT_VS 7 GND 15 DDC_CLK 8 GND Parallel Connector file:///F|/Service%20Manuals/Dell/Latitude/d500/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D500 Service Manual Pin Signal Pin Signal 1 STROBE– 10 ACK– 2 PD0 11 BUSY 3 PD1 12 PE 4 PD2 13 SLCT 5 PD3 14 AFD/3M– 6 PD4 15 ERROR– 7 PD5 16 INIT– 8 PD6 17 SLIN– 9 PD7 18–25 GND S-Video TV-Out Connector file:///F|/Service%20Manuals/Dell/Latitude/d500/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D500 Service Manual S-Video Pin Signal 1 GND 2 GND 3 DLUMA-L 4 DCRMA-L Composite Video Pin Signal 5 NC 6 DCMPS-L 7 GND Serial Connector file:///F|/Service%20Manuals/Dell/Latitude/d500/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D500 Service Manual Pin Signal Pin Signal 1 DCD 6 DSR 2 RXDA 7 RTS 3 TXDA 8 CTS 4 DTR 9 RI 5 GND Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d500/pinouts.
