Dell Latitude E5440 オーナーズマニュアル 規制モデル: P44G 規制タイプ: P44G001
メモ、注意、警告 メモ: コンピュータを使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その問題を回避するための方法を説明して います。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 著作権 © 2014 Dell Inc. 無断転載を禁じます。この製品は、米国および国際著作権法、ならびに米国および国際知的財産 法で保護されています。Dell™、およびデルのロゴは、米国および / またはその他管轄区域における Dell Inc. の商標です。 本書で使用されているその他すべての商標および名称は、各社の商標である場合があります。 2014 -11 Rev.
目次 1 コンピューター内部の作業................................................................................... 6 コンピュータ内部の作業を始める前に..................................................................................................6 コンピューターの電源を切る................................................................................................................ 7 コンピューター内部の作業を終えた後に.............................................................................................. 8 2 コンポーネントの取り外しと取り付け.............................
コイン型電池の取り付け..................................................................................................................... 25 ディスプレイヒンジの取り外し.......................................................................................................... 25 ディスプレイヒンジの取り付け.......................................................................................................... 26 パームレストの取り外し.....................................................................................................................
6 デルへのお問い合わせ.........................................................................................
1 コンピューター内部の作業 コンピュータ内部の作業を始める前に コンピュータの損傷を防ぎ、ユーザー個人の安全を守るため、以下の安全に関するガイドラインに従ってく ださい。特記がない限り、本書に記載される各手順は、以下の条件を満たしていることを前提とします。 • コンピュータに付属の「安全に関する情報」を読んでいること。 • コンポーネントは交換可能であり、別売りの場合は取り外しの手順を逆順に実行すれば、取り付け可能で あること。 警告: コンピュータ内部の作業を始める前に、コンピュータに付属の「安全に関する情報」に目を通し てください。安全に関するベストプラクティスについては、規制コンプライアンスに関するホームペー ジ(www.dell.
4. コンピュータからすべてのネットワークケーブルを外します。 5. コンピュータおよび取り付けられているすべてのデバイスをコンセントから外します。 6. ディスプレイを閉じ、平らな作業台の上でコンピュータを裏返します。 メモ: システム基板の損傷を防ぐため、コンピュータ内部の作業を行う前にメインバッテリーを取 り外してください。 7. メインバッテリーを取り外します。 8. コンピュータを表向きにします。 9. ディスプレイを開きます。 10. 電源ボタンを押して、システム基板の静電気を除去します。 注意: 感電防止のため、ディスプレイを開く前に、必ずコンセントからコンピュータの電源プラグ を抜いてください。 注意: コンピュータの内部に触れる前に、コンピュータの裏面など塗装されていない金属面に触れ、 静電気を除去します。作業中は定期的に塗装されていない金属面に触れ、内部コンポーネントを損 傷する恐れのある静電気を放出してください。 11.
2. 次に、以下に示す Start(スタート)メニューの右下の矢印をクリックし、Shut Down(シャッ トダウン)をクリックします。 2. コンピューターと取り付けられているデバイスすべての電源が切れていることを確認します。オペレー ティングシステムをシャットダウンしてもコンピューターとデバイスの電源が自動的に切れない場合 は、電源ボタンを約 4 秒間押し続けて電源を切ります。 コンピューター内部の作業を終えた後に 交換(取り付け)作業が完了したら、コンピューターの電源を入れる前に、外付けデバイス、カード、ケー ブルなどを接続したか確認してください。 注意: コンピュータを損傷しないために、この特定の Dell コンピュータのために設計されたバッテリー のみを使用します。他の Dell コンピュータのために設計されたバッテリーは使用しないでください。 1. ポートレプリケーター、バッテリースライス、メディアベースなどの外部デバイスを接続し、ExpressCard などのカードを交換します。 2.
2 コンポーネントの取り外しと取り付け このセクションには、お使いのコンピューターからコンポーネントを取り外し、取り付ける手順についての 詳細な情報が記載されています。 奨励するツール この文書で説明する操作には、以下のツールが必要です。 • 細めのマイナスドライバー • #0 プラスドライバ • #1 プラスドライバ • 小型のプラスチックスクライブ 9
システムの概要 図 1. 内部図 — 背面 1. アイソレーションキャップ付きのハードドライ 2. ブ 3. メモリモジュール 5. WLAN カード 10 4.
図 2. 内部図 — 前面 1. 電源コネクタ 2. I/O ボード(左) 3. システムファン 4. ExpressCard ケージ 5. スピーカ 6. ステータスライトボード 7. システム基板 8. I/O ボード(右) バッテリーの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次の手順を実行します。 a. バッテリーリリースラッチをアンロック位置にスライドさせます。 b.
バッテリーの取り付け 1. カチッと所定の位置に収まるまで、バッテリーをスロットに挿入します。 2. 「コンピュータ内部の作業の後で」の手順に従います。 SD カードの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. SD カードを押し込んでアンロックします。 3. SD カードをコンピュータから引き出します。 SD カードの取り付け 1. 所定の位置にカチッと収まるまで、SD カードをスロットに押し込みます。 2. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ExpressCard の取り外し 1. 「コンピュータの作業を始める前に」の手順に従います。 2. 次の手順を実行します。 a. ExpressCard カードを押し込んで、コンピュータから解除します [1] 。 b.
ExpressCard の取り付け 1. カチッと所定の位置に収まるまで、ExpressCard をスロットに差し込みます。 2. 「コンピュータ内部の作業を終えた後に」の手順に従います。 SIM カードの取り外し 1. 「コンピュータの作業を始める前に」の手順に従います。 2. バッテリーを取り外します。 3. バッテリーウォールにある SIM カードを押してロックを解除します。 4. SIM カードをコンピュータから引き出します。 メモ: コンピュータの SIM スロットはマイクロ SIM のみサポートしています。 SIM カードの取り付け 1. SIM カードをスロットに差し込みます。 2. バッテリーを取り付けます。 3. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ディスプレイベゼルの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. バッテリーを取り外します。 3. 次の手順を実行します。 a. ディスプレイベゼルの下端を持ち上げます。 b.
4. ディスプレイベゼルをコンピュータから取り外します。 ディスプレイベゼルの取り付け 1. ディスプレイベゼルをディスプレイアセンブリに載せます。 2. ディスプレイベゼルの上端を最初に押し込み、ディスプレイアセンブリに完全にはまるまでベゼル全体 を押し込みます。 3. バッテリーを取り付けます。 4. 「コンピュータ内部の作業の後で」の手順に従います。 ディスプレイパネルの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ディスプレイベゼル 3. ディスプレイパネルを固定しているネジを外して、パネルを裏返します。 4.
a. 透明シートテープを剥し、低電圧差動信号(LVDS)ケーブルをディスプレイパネルの背面から外し ます。 b. ディスプレイパネルをディスプレイアセンブリから取り外します。 ディスプレイパネルの取り付け 1. ディスプレイパネルをディスプレイアセンブリにセットします。 2. ディスプレイパネルを元の位置に合わせます。 3. 低電圧差動信号(LVDS)ケーブルをディスプレイパネルに接続し、テープを取り付けます。 4. ディスプレイパネルを裏返し、ネジを締めてディスプレイパネルを固定します。 5. 次のコンポーネントを取り付けます。 a. ディスプレイベゼル b. バッテリー 6. 「コンピュータ内部の作業を終えた後に」の手順に従います。 カメラの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ディスプレイベゼル 3. 次の手順を実行します。 a. カメラ / マイクモジュールを固定しているネジを外します。 b. カメラケーブルを外します。 c.
カメラの取り付け 1. カメラとマイクモジュールを所定の位置に置きます。 2. カメラケーブルを接続します。 3. ネジを締めてカメラとマイクモジュールを固定します。 4. 次のコンポーネントを取り付けます。 a. ディスプレイベゼル b. バッテリー 5. 「コンピュータ内部の作業を終えた後に」の手順に従います。 キーボードトリムの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. バッテリーを取り外します。 3. 次の手順を実行します。 a. キーボードトリムの両端と上端を取り出します。 b.
キーボードトリムの取り付け 1. キーボードトリムを所定の位置に合わせます。 2. カチッと所定の位置に収まるまで、キーボードトリムの両端を押し込みます。 3. バッテリーを取り付けます。 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 キーボードの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. キーボードトリム 3.
4. キーボードを固定しているネジを外し [1] 、キーボードを持ち上げて [2] 、コンピュータから取り外しま す [3]。 5.
キーボードの取り付け 1. キーボードケーブルをキーボードに接続します。 2. すべての金属製タブが所定の位置に収まるように、キーボードを所定の位置にセットします。 3. キーボードの左右を押し下げて、すべての留め具がコンピュータと完全に噛み合っていることを確認し ます。 4. ネジを取り付けて、キーボードをパームレストに固定します。 5. コンピュータの背面にネジを取り付けます。 6. 次のコンポーネントを取り付けます。 a. キーボードトリム b. バッテリー 7. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ベースカバーの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. バッテリーを取り外します。 3. 次の手順を実行します。 a. ベースカバーを固定しているネジを外します。 b.
ベースカバーの取り付け 1. 所定の位置にカチッと収まるまで、ベースカバーをスロットに差し込みます。 2. ベースカバーをコンピュータに固定するネジを取り付けます。 3. バッテリーを取り付けます。 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 オプティカルドライブの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ベースカバー 3. 次の手順を実行します。 a. オプティカルドライブをコンピュータに固定しているネジを外します。 b.
4. オプティカルドライブブラケットを取り外してから、次の手順を実行します。 a. オプティカルドライブブラケットを固定しているネジを外します[1]。 b. オプティカルドライブブラケットをオプティカルドライブから取り外します[2]。 5. オプティカルドライブベゼルのタブを外して、オプティカルドライブベゼルをオプティカルドライブか ら離します。 6. オプティカルドライブベゼルを取り外します。 オプティカルドライブの取り付け 1. オプティカルドライブベゼルのタブをはめ込み、オプティカルドライブに取り付けます。 2. オプティカルドライブブラケットを取り付けます。 3. オプティカルドライブブラケットを固定するネジを締めます。 4. オプティカルドライブをコンピュータに挿入します。 5. ネジを締めて、オプティカルドライブを所定の位置に固定します。 6. 次のコンポーネントを取り付けます。 a. ベースカバー b. バッテリー 7.
ハードドライブの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ベースカバー 3. 次の手順を実行します。 a. ハードドライブブラケットを所定の位置に固定しているネジを外します。 b. ハードドライブを引き出して、コネクタから取り外します。 4. ハードドライブアイソレーションのキャップをハードドライブから取り外します。 ハードドライブの取り付け 1.
2. ハードドライブを所定のコネクタにセットします。 3. ハードドライブブラケットをハードドライブに置き、ネジを締めてハードドライブブラケットを所定の 位置に固定します。 4. 次のコンポーネントを取り付けます。 a. ベースカバー b. バッテリー 5. 「コンピュータ内部の作業を終えた後に」の手順に従います。 メモリモジュールの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ベースカバー 3. メモリモジュールが持ち上がるまで、固定クリップを引き出します。 4. メモリモジュールを持ち上げてコンピュータから取り出します。 メモリモジュールの取り付け 1. メモリをメモリソケットに挿入します。 2. クリップを押して、メモリモジュールをシステム基板に固定します。 3. 次のコンポーネントを取り付けます。 a. ベースカバー b.
4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 WLAN カードの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ベースカバー 3. 次の手順を実行します。 a. アンテナケーブルを WLAN カードから外します。 b. WLAN カードをコンピュータに固定しているネジを外します。 c. WLAN カードをシステム基板上のスロットから取り外します。 WLAN カードの取り付け 1. WLAN カードをシステム基板の所定のコネクタに差し込みます。 2. WLAN カードに記された対応コネクタにアンテナケーブルを接続します。 3. WLAN カードをコンピュータに固定するネジを締めます。 4. 次のコンポーネントを取り付けます。 a. ベースカバー b. バッテリー 5. 「コンピュータ内部の作業を終えた後に」の手順に従います。 コイン型電池の取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a.
コイン型電池の取り付け 1. 粘着剤が付いている側を下向きにしてコイン型電池をシステム基板に載せます。 2. コイン型電池ケーブルをシステム基板に接続します。 3. 次のコンポーネントを取り付けます。 a. ベースカバー b. バッテリー 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ディスプレイヒンジの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. バッテリー b. ベースカバー c. キーボードトリム d. キーボード 3.
4. ディスプレイヒンジをコンピュータの前面に固定しているネジを外します。ディスプレイヒンジを押し て、コンピュータから取り外します。 ディスプレイヒンジの取り付け 1. ディスプレイヒンジをコンピュータに置きます。 2. ネジを締めて、ディスプレイヒンジをコンピュータの前面と背面に固定します。 3. 次のコンポーネントを取り付けます。 a. b. c. d. キーボード キーボードトリム ベースカバー バッテリー 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 パームレストの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. 3.
4. 次のケーブルを外します。 a. b. c. d. 5. メディアボタンケーブル タッチパッドケーブル 指紋スキャナーケーブル 電源ボタンケーブル 次の手順を実行します。 a. パームレストをコンピュータに固定しているネジを外します。 b.
パームレストの取り付け 1. パームレストアセンブリをコンピュータの元の位置に合わせ、そこにはめ込みます。 2. 以下のケーブルをシステム基板に接続します。 a. b. c. d. 電源ボタンケーブル 指紋スキャナーケーブル タッチパッドケーブル メディアボタンケーブル 3. ネジを締めてパームレストをコンピュータの前面と背面に固定します。 4. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. ディスプレイヒンジ ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 5. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ディスプレイアセンブリの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. SD カード b. バッテリー c.
d. e. f. g. キーボードトリム キーボード ディスプレイヒンジ パームレスト 3. WLAN ケーブルを外して、配線チャネルから取り外します。 4. 次の手順を実行します。 a. ディスプレイケーブルコネクタを固定しているネジを外し、システム基板から取り外します。 b. システム基板からディスプレイケーブルを外します。 5.
メモ: 上記のディスプレイアセンブリの取り外し手順は、コンピュータのタッチパネルおよびノンタッ チパネルのどちらのバージョンにも適用できます。 ディスプレイアセンブリの取り付け 1. ディスプレイアセンブリを所定の位置に固定するネジを締めます。 2. WLAN ケーブルをシャーシの穴に差し込みます。 3. ディスプレイケーブルをコンパートメントに沿って配線し、システム基板のコネクタに接続します。 4. WLAN ケーブルをコネクタに接続します。 5. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. パームレスト ディスプレイヒンジ キーボード キーボードトリム ベースカバー バッテリー SD カード 6. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ExpressCard ケージの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e.
f. ディスプレイヒンジ g. パームレスト 3. 次の手順を実行します。 a. ExpressCard ケージを固定しているネジを外します。 b. ExpressCard ケージを持ち上げてコンピュータから取り外します。 ExpressCard ケージの取り付け 1. ExpressCard ケージをコンピュータの元の位置に合わせ、そこにはめ込みます。 2. ExpressCard ケージをシステム基板に固定するネジを取り付けます。 3. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. パームレスト ディスプレイヒンジ キーボード キーボードトリム ベースカバー バッテリー SD カード 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 システムファンの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i.
j. 3. パームレスト 次のケーブルを外します。 a. システムファンケーブル b. I/O ボードケーブル 4. システムファンを固定しているねじ外し、システムファンを持ち上げてコンピュータから取り外します。 システムファンの取り付け 1. システムファンをコンピュータ上にセットします。 2. システムファンケーブルをシステム基板に接続します。 3. I/O ボードケーブルをコネクタに接続します。 4. ネジを締めてシステムファンをコンピュータに固定します。 5. 次のコンポーネントを取り付けます。 a. b. c. d.
e. f. g. h. i. j. オプティカルドライブ キーボード キーボードトリム ベースカバー バッテリー SD カード 6. 「コンピュータ内部の作業を終えた後に」の手順に従います。 システム基板の取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. j. k. l. m. 3. SD カード バッテリー ベースカバー キーボードトリム キーボード メモリ オプティカルドライブ ハードドライブ WLAN カード ディスプレイヒンジ パームレスト システムファン ExpressCard ケージ 次のケーブルを外します。 a. コイン型電池ケーブル b. スピーカケーブル 4. コンピュータを裏返して次のケーブルを外します。 a. 電源ケーブル b. ステータスライトボードケーブル c.
5. 次の手順を実行します。 a. ディスプレイケーブルコネクタを固定しているネジを外し、システム基板から取り外します。 b. ディスプレイケーブルと電源コネクタケーブルをシステム基板から外します。 6.
システム基板の取り付け 1. システム基板をコンピュータの元の位置に合わせます。 2. システム基板をコンピュータに固定するネジを取り付けて締めます。 3. 以下のケーブルを接続します。 a. I/O ボードケーブル b. 電源コネクタケーブル c. ステータスライトボードケーブル 4. コンピュータを裏返して、コイン型電池ケーブルとスピーカケーブルをシステム基板に接続します。 5. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. j. k. l. m. ExpressCard ケージ システムファン パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 6.
ヒートシンクの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. 3. SD カード バッテリー ベースカバー キーボードトリム キーボード メモリ オプティカルドライブ ハードドライブ WLAN カード ディスプレイヒンジ パームレスト システムファン ExpressCard ケージ システム基板 次の手順を実行します。 a. ヒートシンクを所定の位置に固定しているネジを外します。 b. ヒートシンクを持ち上げて、コンピュータから取り外します。 ヒートシンクの取り付け 1. システム基板にヒートシンクをセットします。 2. ネジを締めてヒートシンクをコンピュータに固定します。 3. 次のコンポーネントを取り付けます。 a. システム基板 b.
c. d. e. f. g. h. i. j. k. l. m. n. システムファン パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 I/O ボード(左)の取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. 3. SD カード バッテリー ベースカバー キーボードトリム キーボード メモリ オプティカルドライブ ハードドライブ WLAN カード ディスプレイヒンジ パームレスト システムファン ExpressCard ケージ システム基板 次の手順を実行します。 a. 左 I/O ボードをコンピュータに固定しているネジを外します。 b.
I/O ボード(左)の取り付け 1. I/O ボードをコンピュータに置きます。 2. ネジを締めて I/O ボードをコンピュータに固定します。 3. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. システム基板 ExpressCard ケージ システムファン パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 I/O ボード(右)の取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. 3.
I/O ボード(右)の取り付け 1. I/O ボードをコンピュータに置きます。 2. ネジを締めて I/O ボードをコンピュータに固定します。 3. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. システム基板 ExpressCard ケージ システムファン パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 電源コネクタの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h.
i. j. k. l. m. n. 3. WLAN カード ディスプレイヒンジ パームレスト ExpressCard ケージ システムファン システム基板 次の手順を実行します。 a. 電源コネクタケーブルを配線チャネルから外します。 b. 電源コネクタを持ち上げて、コンピュータから取り外します。 電源コネクタの取り付け 1. 電源コネクタをコンピュータの所定の位置にセットします。 2. 電源コネクタケーブルを配線チャネルに配線します。 3. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. システム基板 システムファン ExpressCard ケージ パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 4. 「コンピュータ内部の作業を終えた後に」の手順に従います。 スピーカの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a.
c. d. e. f. g. h. i. j. k. l. m. n. 3. ベースカバー キーボードトリム キーボード メモリ オプティカルドライブ ハードドライブ WLAN カード ディスプレイヒンジ パームレスト システムファン ExpressCard ケージ システム基板 次の手順を実行します。 a. スピーカケーブルを配線チャネルから外します。 b. スピーカをコンピュータに固定しているネジを外します。 c. スピーカを持ち上げて、コンピュータから取り外します。 スピーカの取り付け 1. スピーカをコンピュータに置きます。 2. スピーカケーブルを配線チャンネルに固定します。 3. ネジを締めてスピーカをコンピュータに固定します。 4. 次のコンポーネントを取り付けます。 a. b. c. d. e. f.
g. h. i. j. k. l. m. n. ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 5. 「コンピュータ内部の作業を終えた後に」の手順に従います。 ステータスライトボードの取り外し 1. 「コンピュータ内部の作業を始める前に」の手順に従います。 2. 次のコンポーネントを取り外します。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. o. 3. SD カード バッテリー ベースカバー キーボードトリム キーボード メモリ オプティカルドライブ ハードドライブ WLAN カード ディスプレイヒンジ パームレスト システムファン ExpressCard ケージ システム基板 スピーカ 次の手順を実行します。 a. LED カバーを取り外します。 b. ステータスライトボードケーブルを外して、ステータスライトボードを固定しているネジを外しま す。 c.
ステータスライトボードの取り付け 1. ステータスライトボードをコンピュータの所定の位置にセットします。 2. ステータスライトボードケーブルをコネクタに接続します。 3. ネジを締めて、ステータスライトボードをコンピュータに固定します。 4. LED カバーをステータスライトボードに置きます。 5. 次のコンポーネントを取り付けます。 a. b. c. d. e. f. g. h. i. j. k. l. m. n. o. スピーカ システム基板 システムファン ExpressCard ケージ パームレスト ディスプレイヒンジ WLAN カード ハードドライブ オプティカルドライブ メモリ キーボード キーボードトリム ベースカバー バッテリー SD カード 6.
3 システムセットアップ システムセットアップでコンピューターのハードウェアを管理し BIOS レベルのオプションを指定すること ができます。システムセットアップで以下の操作が可能です: • ハードウェアの追加または削除後に NVRAM 設定を変更する。 • システムハードウェアの構成を表示する。 • 統合されたデバイスの有効 / 無効を切り替える。 • パフォーマンスと電力管理のしきい値を設定する。 • コンピューターのセキュリティを管理する。 起動順序 起動順序ではシステムセットアップで定義された起動デバイスの順序および起動ディレクトリを特定のデバ イス(例: オプティカルドライブまたはハードドライブ)にバイパスすることができます。パワーオンセルフ テスト(POST)中に、Dell のロゴが表示されたら、以下の操作が可能です: • を押してシステムセットアップにアクセスする • を押して 1 回限りの起動メニューを立ち上げる 1 回限りの起動メニューでは診断オプションを含むオプションから起動可能なデバイスを表示します。起動 メニューのオプションは以下の通り
表 1. ナビゲーションキー キー ナビゲーション 上矢印 前のフィールドに移動します。 下矢印 次のフィールドへ移動します。 選択したフィールドに値を入力するか(該当する場合)、フィールド内のリンクに移動 することができます。 スペースバー ドロップダウンリストがある場合は、展開したり折りたたんだりします。 次のフォーカス対象領域に移動します。 メモ: 標準グラフィックブラウザ用に限られます。 メイン画面が表示されるまで、前のページに戻ります。メイン画面で を押すと、 未保存の変更を保存するプロンプトが表示され、システムが再起動します。 セットアップユーティリティ のヘルプファイルを表示します。 セットアップユーティリティのオプション メモ: お使いのコンピューターおよび取り付けられているデバイスによっては、本項に一覧表示された 項目の一部がない場合があります。 表 2.
オプション 説明 Boot Sequence Boot Sequence コンピュータがオペレーティングシステム を認識する順序を変更することができま す。オプションは次の通りです。 • • • • • Diskette Drive(ディスケットドライブ) Internal HDD USB Storage Device(USB ストレージ デバイス) CD/DVD/CD-RW Drive(CD/DVD/CDRW ドライブ) Onboard NIC(オンボード NIC) デフォルトでは、すべてのオプションがチ ェックされています。また、オプションの 選択を解除または起動順序を変更できま す。 Boot List Option 起動リストオプションを変更することがで きます。 • • Legacy(レガシー) UEFI Advanced Boot Options このオプションを使用すると、レガシーオプション ROM をロードできます。Enable Legacy Option ROM(レガシーオプション ROM を有効にする)はデフォルトでチェッ クが外されています。 Date/Time
オプション 説明 • • • SATA Operation 内蔵 SATA ハードドライブコントローラを設定することができます。オプ ションは次の通りです。 • • • Drives SATA-0 SATA-1 SATA-2 SATA-3 このフィールドにより、システム起動時に内蔵ドライブのハードドライブ エラーを報告するかどうかを決めます。このテクノロジは、SMART(Self Monitoring Analysis and Reporting Technology)仕様の一部です。このオ プションはデフォルトで無効に設定されています。 • USB Configuration 無効 AHCI RAID On(RAID オン) :このオプションはデフォルトで有効に設定され ています。 オンボードの SATA ドライブを設定することができます。すべてのドライ ブがデフォルトで有効に設定されています。オプションは以下のとおりで す。 • • • • SMART Reporting COM2 COM3 COM4 Enable SMART Reporting(SMART レポートを有効にする)
オプション 説明 キーボードの輝度レベルは 25 ~ 100 パーセントの間で設定できます。 • • • • • Disabled(無効) Level is 25%(レベル 25%) Level is 50%(レベル 50%) Level is 75%(レベル 75%) Level is 100%(レベル 100%):このオプションはデフォルトでは有効 になっています Unobtrusive Mode このオプションが有効になっている場合、Fn+B を押すと、システム内のす べてのライトとサウンドエミッションがオンになります。通常の操作を再 開するには、Fn+B を再度押します。このオプションはデフォルトでは無効 になっています。 Miscellaneous Devices 以下のデバイスの有効 / 無効を切り替えることができます。 • • • • • • Enable Microphone(マイクを有効にする) Enable Camera(カメラを有効にする) Enable Express card(Express カードを有効にする) Enable Hard Drive Free Fall
オプション 説明 デフォルト設定:Not set(未設定) System Password システムパスワードを設定、変更、または削除することができます。 メモ: パスワードが正常に変更されると、すぐに反映されます。 デフォルト設定:Not set(未設定) Internal HDD-1 Password システムの内蔵ハードディスクドライブを設定または変更することができ ます。 メモ: パスワードが正常に変更されると、すぐに反映されます。 デフォルト設定:Not set(未設定) Strong Password 強力なパスワードを設定するオプションを常に強制することができます。 デフォルト設定:Enable Strong Password(強力なパスワードを有効にす る) は選択されません。 メモ: Strong Password(強力なパスワード)を有効に設定すると、 Admin パスワードとシステムパスワードに大文字と小文字をそれぞ れ少なくとも 1 文字使い、8 文字以上の長さにしなければなりません。 Password Configuration Administrator パスワー
オプション 説明 • • 無効 Activate(アクティブ化) メモ: Activate(起動) および Disable(無効) オプションでは、機能 を永久的に起動または無効にします。その後の変更はできません。 Deactivate(非アクティブ化)(デフォルト) CPU XD Support プロセッサの Execute Disable(実行無効)モードを有効にすることができ ます。 Enable CPU XD Support(CPU XD サポートを有効にする)(デフォルト) OROM Keyboard Access 起動中にホットキーを使用して、Option ROM Configuration(オプション ROM 設定)画面を表示するオプションを設定することができます。オプシ ョンは以下のとおりです。 • • • 有効 One Time Enable(1 回のみ有効) 無効 デフォルト設定:Enable(有効) Admin Setup Lockout 管理者パスワードが設定されている場合、ユーザーによるセットアップユ ーティリティの起動を防止することができます。 Default S
オプション 説明 • • • • • Replace from File(ファイルから交換)- 現在のキーをユーザーが選択 したファイルのキーと交換します。 Append from File(ファイルから追加)- ユーザーが選択したファイル から現在のデータベースにキーを追加します。 Delete(削除)- 選択したキーを削除します。 Reset All Keys(すべてのキーをリセット)- デフォルト設定にリセッ トします。 Delete All Keys(すべてのキーを削除)- すべてのキーを削除します。 メモ: Custom Mode(カスタムモード)を無効にすると、すべての変 更が消去され、キーはデフォルト設定に復元されます。 表 7.
表 8.
オプション 説明 Peak Shift このオプションでは、1 日のピーク時の AC 消費を最小限に抑えることがで きます。このオプションを有効にすると AC が搭載されていてもバッテリ ーでのみ作動します。 Advanced Battery Charge Configuration このオプションでは、バッテリーの性能を最大限に高めることができます。 標準充電アルゴリズムと他のテクニックを使用して、非作業時間にバッテ リーの性能を最大限に高めます。 無効(デフォルト) Primary Battery Charge Configuration バッテリーの充電モードを選択することができます。オプションは以下の とおりです。 • • • • • 適応 標準 Express Charge(高速充電):このオプションはデフォルトで有効に設 定されています。 Primarily AC use(主に AC を使用) カスタム Custom Charge(カスタム充電)が選択されている場合は、Custom Charge Start(カスタム充電開始)と Custom Charge Stop(カスタム充電
オプション 説明 デフォルト設定:Enable Adapter Warnings(アダプタ警告を有効にする) Keypad (Embedded) 内蔵キーボードに組み込まれているキーパッドを有効にする 2 つの方法の うち、1 つを選択することができます。 • • Fn Key Only(Fn キーのみ):このオプションはデフォルトで有効に設 定されています。 By Numlock(Numlock を使用) メモ: キーボード (Embedded) オプションは、Latitude E 5540 ではサ ポートされていません。 Mouse/Touchpad マウスとタッチパッドからの入力をシステムがどう処理するかを定義する ことができます。オプションは以下のとおりです。 • • • Numlock Enable Serial Mouse(シリアルマウス) PS2 Mouse(PS2 マウス) Toushpad/PS-2 Mouse(タッチパッド /PS-2 マウス) :このオプション はデフォルトで有効に設定されています。 コンピュータの起動時に Numlock オプションを有効にすることがで
表 10.
オプション 説明 すべてのオプションがデフォルトで有効に設定されています。 表 12. メンテナンス オプション 説明 Service Tag お使いのコンピューターのサービスタグが表示されます。 Asset Tag アセットタグがまだ設定されていない場合、システムアセットタグを作成 することができます。このオプションはデフォルトでは設定されていませ ん。 表 13.
10. 希望のダウンロード方法を以下から選択してくださいウィンドウで希望のダウンロード方法を選択し、 Download File(ファイルのダウンロード)をクリックします。 ファイルのダウンロードウィンドウが表示されます。 11. ファイルをコンピュータに保存する場合は、保存をクリックします。 12.
4. 入力したシステムパスワードをもう一度入力し、OK をクリックします。 5. セットアップパスワードを選択してシステムパスワードを入力し、 または を押します。 セットアップパスワードの再入力を求めるメッセージが表示されます。 6. 入力したセットアップパスワードをもう一度入力し、OK をクリックします。 7. を押すと、変更の保存を求めるメッセージが表示されます。 8. を押して変更を保存します。 コンピューターが再起動します。 既存のシステムパスワードおよび / またはセットアップパスワードの削除または 変更 既存のシステムパスワードおよび/またはセットアップパスワードを削除または変更する前にパスワード状 態がロック解除(システムセットアップで)になっていることを確認します。パスワード状態がロックされて いる場合、既存のシステムパスワードまたはセットアップパスワードを削除または変更することはできませ ん。 システムセットアップを入力するには、電源投入または再起動の直後に を押します。 1.
4 診断 コンピューターに問題が起こった場合、デルのテクニカルサポートに電話する前に ePSA 診断を実行してく ださい。診断プログラムを実行する目的は、特別な装置を使用せず、データが失われる心配をすることなく コンピューターのハードウェアをテストすることです。お客様がご自分で問題を解決できない場合でも、サ ービスおよびサポート担当者が診断プログラムの結果を使って問題解決の手助けを行うことができます。 ePSA(強化された起動前システムアセスメント)診断 ePSA 診断 (システム診断としても知られている) ではハードウェアの完全なチェックを実施します。ePSA には BIOS が埋め込まれており、内部的に BIOS によって起動されます。埋め込まれたシステム診断では以下 のことが可能な特定のデバイスまたはデバイスグループにオプションのセットを提供します: • テストを自動的に、または対話モードで実行 • テストの繰り返し • テスト結果の表示または保存 • 詳細なテストで追加のテストオプションを実行し、障害の発生したデバイスに関する詳しい情報を得る • テストが問題なく終了したかどうかを
デバイスステータスライト アイコ ン 説明 コンピュータに電源を入れると点灯し、コンピュータが省電力モードの場合は点滅します。 コンピュータがデータを読み取ったり、書き込んだりしている場合に点灯します。 点灯、または点滅してバッテリーの充電状態を示します。 ワイヤレスネットワークが有効の場合、点灯します。 バッテリーステータスライト コンピューターがコンセントに接続されている場合、バッテリーライトは次のように動作します。 黄色と白色が交 互に点滅 認定されていない、またはサポートされていないデル以外の AC アダプターがラップ トップに接続されている。 黄色が短く、白 色が長く交互に 点滅 AC アダプターに接続されており、一時的なバッテリーの不具合が発生した。 黄色が連続的に 点滅 AC アダプターに接続されており、致命的なバッテリーの不具合が発生した。 消灯 AC アダプターに接続されており、バッテリーがフル充電モードになっている。 白色点灯 AC アダプターに接続されており、バッテリーが充電モードになっている。 60
5 仕様 メモ: 提供される内容は地域により異なる場合があります。コンピュータの構成の詳細を確認するに (スタートアイコン) → ヘルプとサポート の順にクリックし、お使いのコンピュー は、スタート タに関する情報を表示するオプションを選択してください。 表 14. システム情報 機能 仕様 DRAM バス幅 64 ビット フラッシュ EPROM SPI 32Mbits + 64Mbits PCIe Gen1 バス 100 MHz 外付けバスの周波数 DMI(5GT/秒) 表 15. プロセッサ 機能 仕様 タイプ • • • L3 キャッシュ 最大 8 MB Intel Core i3 シリーズ Intel Core i5 シリーズ Intel Core i7 シリーズ 表 16.
表 17. mSATA サポート 機能 仕様 Express カード I/O および外付けグラフィッ クスの設定 Latitude E5440 および Latitude E5540 の両方で mSATA サ ポートなし。 他の構成 Latitude E5440 および Latitude E5540 の両方で mSATA サ ポート。 外付けグラフィックスおよびすべての UMA • グラフィックス設定で Express カード I/O な • し Latitude E5440 の mSATA および WWAN をサポート Latitude E5540 の mSATA をサポート 表 18.
表 21. ポートとコネクタ 機能 仕様 オーディオ(オプション) マイクコネクタ/ステレオヘッドフォン/スピーカーコネク タ(1) ビデオ • • ネットワークアダプタ RJ-45 コネクタ(1) USB 2.0 • • 15 ピン VGA コネクタ(1) 19 ピン HDMI コネクタ 4 ピン USB 2.0 準拠コネクタ(E5440)(1) 4 ピン USB 2.0 準拠コネクタ(E5540)(2) メモ: Latitude E 5540 コンピュータがドッキングステ ーションに接続されると、Latitude E 5540 コンピュー タの背面にある USB 2.0 コネクタが無効になります。 USB 3.0 USB 3.0 準拠コネクタ(2) メモリカードリーダー 8-in-1 メモリカードリーダー(1) ドッキングポート (1) 加入者識別モジュール(SIM)ポート (1)(E5440 のみ) 表 22.
機能 仕様 最大輝度 200 ニット Latitude E5540: 高さ 210 mm(8.26 インチ) 幅 360 mm(14.17 インチ) 対角線 394.24 mm(15.60 インチ) 有効領域(X/Y) 344.23 mm x 193.54 mm 最大解像度 • • 最大輝度 HD が 220 ニット、FHD が 300 ニット 1366 x 768 ピクセル 1920 x 1080 ピクセル 動作角度 0°(閉じた状態) ~ 135° リフレッシュレート 60 Hz 最小視角: 水平方向 • • HD が +/- 40° FHD が +/- 60° 垂直方向 • • HD が +10°/-30° FHD が +/-50° ピクセルピッチ: Latitude E5440 0.2265 mm x 0.2265 mm Latitude E5540 • • HD が 0.2520 mm x 0.2520 mm FHD が 0.1790 x 0.1790 表 23.
表 25. バッテリー 機能 仕様 タイプ 4 セル、6 セル、または 9 セル「スマート」リチウム イオン 寸法: 高さ 4 セル、6 セル、および 9 セル 20.00 mm(0.79 インチ) 4 セルおよび 6 セル 208.00 mm(8.18 インチ) 9 セル 214.00 mm(8.43 インチ) 幅 奥行き 4 セルおよび 6 セル 48.08 mm(1.89 インチ) 9 セル 71.79 mm(2.83 インチ) 重量 4 セル 240.00 g(0.53 ポンド) 6 セル 344.73 g(0.76 ポンド) 9 セル 508.20 g(1.12 ポンド) 電圧 4 セル 14.8 VDC 6 セルおよび 9 セル 11.
機能 Latitude E5440 Latitude E5540 出力電力 65 W 90 W 出力電流 3.34 A(連続稼動時) 4.62 A(連続稼働時) 定格出力電圧 19.5 +/– 1.0 VDC 19.5 +/– 1.0 VDC 稼働時 0 °C ~ 40 °C(32 °F ~ 104 °F) 0 °C ~ 40 °C(32 °F ~ 104 °F) 非動作時 –40 °C ~ 70 °C(–40 °F ~ 158 °F) –40 °C ~ 70 °C(–40 °F ~ 158 °F) 温度範囲: 表 27. 物理的仕様 Latitude E5440 物理的仕様 タッチ 高さ Latitude E5540 非タッチ 前面 - 27.70 mm (1.09 インチ) 前面 - 25.20 mm (0.99 インチ) 背面 - 32.20 mm (1.27 インチ) 背面 - 28.65 mm (1.13 インチ) タッチ 非タッチ 前面 - 28.25 mm(1.11 前面 - 26.00 mm (1.
6 デルへのお問い合わせ メモ: お使いのコンピュータがインターネットに接続されていない場合は、購入時の納品書、出荷伝票、 請求書、またはデルの製品カタログで連絡先をご確認ください。 デルでは、オンラインまたは電話によるサポートとサービスのオプションを複数提供しています。サポート やサービスの提供状況は国や製品ごとに異なり、国 / 地域によってはご利用いただけないサービスもござい ます。デルのセールス、テクニカルサポート、またはカスタマーサービスへは、次の手順でお問い合わせい ただけます。 1. dell.com/support にアクセスします。 2. サポートカテゴリを選択します。 3. ページの下部にある 国 / 地域の選択 ドロップダウンリストで、お住まいの国または地域を確認します。 4.