Dell Latitude E5550 / 5550 Benutzerhandbuch Vorschriftenmodell: P37F Vorschriftentyp: P37F001
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG liefert wichtige Informationen, mit denen Sie den Computer besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Arbeiten am Computer 1 Vor der Arbeit an Komponenten im Innern des Computers Die folgenden Sicherheitshinweise schützen den Computer vor möglichen Schäden und dienen der persönlichen Sicherheit des Benutzers. Wenn nicht anders angegeben, ist bei jedem in diesem Dokument beschriebenen Vorgang darauf zu achten, dass die folgenden Bedingungen erfüllt sind: • Sie haben die im Lieferumfang des Computers enthaltenen Sicherheitshinweise gelesen.
Um Schäden am Computer zu vermeiden, führen Sie folgende Schritte aus, bevor Sie mit den Arbeiten im Computerinneren beginnen. 1. Stellen Sie sicher, dass die Arbeitsoberfläche eben und sauber ist, damit die Computerabdeckung nicht zerkratzt wird. 2. Schalten Sie den Computer aus (siehe Ausschalten des Computers). 3. Falls der Computer mit einem Docking-Gerät verbunden ist, trennen Sie die Verbindung.
– Verwenden einer Maus: a. Fahren Sie mit dem Mauszeiger über die rechte obere Ecke des Bildschirms und klicken Sie auf Einstellungen. b. Klicken Sie auf das Symbol und wählen Sie Herunterfahren. oder * • Klicken Sie auf der Startseite auf das und wählen Sie dann Herunterfahren. Unter Windows 7: 1. Klicken Sie auf Start (Start) 2. Klicken Sie auf Herunterfahren . oder 2. 1. Klicken Sie auf Start (Start) . 2.
Entfernen und Einbauen von Komponenten 2 Dieser Abschnitt bietet detaillierte Informationen über das Entfernen und Einbauen von Komponenten Ihres Computers.
Vorder- und Rückansicht 1. Netzwerkanschluss 2. VGA-Anschluss 3. USB 3.0-Anschluss 4. Mikrofone (optional) 5. Kamera 6. Kamerastatusanzeige 7. HDMI-Anschluss 8. Netzanschluss 9. Mikrofon 10. Betriebsschalter 11. USB 3.0-Anschluss mit PowerShare 12. Speicherkartenleser 13. Kontaktloser SmartCard-Leser (optional) 14.
15. Wireless-Statusanzeige 16. Akkuzustandsanzeige 17. Festplattenaktivitätsanzeige 18. Stromversorgungsanzeige 19. Lautsprecher 20. Touchpad 21. SmartCard-Lesegerät (optional) 22. Headset-Anschluss 23. Sicherheitskabeleinschub 24. Docking-Anschluss (optional) 25. Service-Tag-Nummer Entfernen der Bodenabdeckung 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2.
3. Trennen Sie das Akkukabel von seinem Anschluss [1] und lösen Sie das Kabel aus der Kabelführung [2]. 4. Führen Sie folgende Schritte durch: a. Entfernen Sie die Schraube, mit der der Akku am Computer befestigt ist [1]. b. Heben Sie Sie den Akku an und schieben Sie ihn zur Seite, um ihn vom Computer zu entfernen [2] [3]. Einsetzen des Akkus 1. Bringen Sie den Akku an seiner Position am Computer an. 2. Führen Sie das Akkukabel durch die Kabelführung. 3.
Entfernen der Festplattenbaugruppe 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. Bodenabdeckung b. Akku 3. Führen Sie folgende Schritte durch: a. Trennen Sie das Festplattenlaufwerkkabel von seinem Anschluss auf der Systemplatine [1]. b. Entfernen Sie die Schrauben, mit denen die Festplattenlaufwerksbaugruppe am Computer befestigt ist [2]. 4. Entfernen Sie die Festplattenlaufwerksbaugruppe aus dem Computer. 5.
6. Entfernen Sie die Schrauben, mit denen die Festplattenlaufwerkhalterung am Festplattenlaufwerk [1] befestigt ist, und entfernen Sie das Festplattenlaufwerk von der Halterung [2]. Einbauen der Festplattenbaugruppe 1. Platzieren Sie die Festplattenlaufwerkhalterung auf dem Festplattenlaufwerk, um die Schraubenhalterungen auszurichten und ziehen Sie die Schrauben fest, mit denen die Festplattenlaufwerkhalterung befestigt ist. 2.
6. Bauen Sie folgende Komponenten ein: a. Akku b. Bodenabdeckung 7. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen des Speichers 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. Bodenabdeckung b. Akku 3. Hebeln Sie die Klammern, mit denen das Speichermodul gesichert ist, soweit auf bis der Speicher herausspringt, und entfernen Sie ihn von der Systemplatine.
ANMERKUNG: Sie benötigen möglicherweise ein scharfes Werkzeug, um den Tastaturrahmen an den Kanten anzuhebeln. 3. Entfernen Sie den Tastaturrahmen von der Tastatur. Einsetzen des Tastaturrahmens 1. Drücken Sie den Tastaturrahmen auf die Tastatur, bis dieser einrastet. 2. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Tastatur 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2.
4. Entfernen Sie die Schrauben, mit denen die Tastatur am Computer befestigt ist. 5. Entfernen Sie die Tastatur aus dem Computer.
Einsetzen der Tastatur 1. Platzieren Sie die Tastatur und richten Sie sie mit den Schraubenhalterungen am Computer aus. 2. Verbinden Sie das Tastaturkabel und die Touchpad-Kabel mit ihren entsprechenden Anschlüssen auf der Systemplatine. 3. Ziehen Sie die Schrauben fest, mit denen die Tastatur am Computer befestigt wird. 4. Bauen Sie folgende Komponenten ein: a. Tastaturrahmen b. Akku c. Bodenabdeckung 5. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
5. Drücken Sie auf die Handballenstütze, um sie zu lösen und vom Computer zu entfernen [2]. Einsetzen der Handballenstütze 1. Platzieren Sie die Handballenstütze auf den Computer. 2. Schließen Sie die folgenden Kabel an ihre jeweiligen Anschlüssen auf der Systemplatine an: a. b. c. d. Netzteilplatine LED-Platine USH-Platine Touchpad-Platine 3. Ziehen Sie die Schrauben auf der Vorder- und der Rückseite des Computers an, um die Handballenstütze zu befestigen. 4.
5. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers Entfernen der Betriebsschalterplatine 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. b. c. d. e. 3. Bodenabdeckung Akku Tastaturrahmen Tastatur Handballenstütze Führen Sie folgende Schritte durch, um die Betriebsschalterplatine von der Handballenstütze zu entfernen: a.
Entfernen der Platine des SmartCard-Lesegeräts 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. b. c. d. e. f. 3. Bodenabdeckung Akku Speicher Tastaturrahmen Tastatur Handballenstütze Führen Sie folgende Schritte durch: a. Trennen Sie das Kabeln der Platine des SmartCard-Lesegeräts von der USH-Platine [1] [2]. b. Ziehen Sie das Kabel vom Klebeband ab, um es zu lösen [3]. 4.
5. Entfernen Sie die Platine des SmartCard-Lesegeräts von der Handballenstütze. Einbauen der Platine des SmartCard-Lesegeräts 1. Bringen Sie die Platine des SmartCard-Lesegeräts an ihrem Steckplatz auf der Handballenstütze an. 2. Ziehen Sie die Schrauben fest, um die Platine des SmartCard-Lesegeräts an der Handballenstütze zu befestigen. 3. Befestigen Sie das Kabel des SmartCard-Lesegeräts und verbinden Sie das Kabel des SmartCardLesegeräts mit dem entsprechenden Anschluss auf der USH-Platine. 4.
Einsetzen der USH-Platine 1. Platzieren Sie die USH-Platine auf der Handballenstütze. 2. Ziehen Sie die Schrauben fest, um die USH-Platine an der Handballenstütze zu befestigen. 3. Verbinden Sie alle Kabel mit der USH-Platine. 4. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. 5. Handballenstütze Tastatur Tastaturrahmen Festplattenbaugruppe Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
Einbauen der Platine des Fingerabdrucklesers 1. Bringen Sie die Platine des Fingerabdrucklesers an ihrer Position an der Handballenstütze an. 2. Verbinden Sie das Kabel des Fingerabdrucklesers mit der Platine des Fingerabdrucklesers. 3. Platzieren Sie die Metallhalterung an der Platine des Fingerabdrucklesers und ziehen Sie die Schraube fest, mit der die Platine des Fingerabdrucklesers befestigt ist. 4. Bauen Sie folgende Komponenten ein: a. b. c. d. e. 5.
Installieren der LED-Platine 1. Bringen Sie die LED-Platine an ihrem Steckplatz auf der Handballenstütze an. 2. Ziehen Sie die Schraube fest, mit der die LED-Platine an der Handballenstütze befestigt ist. 3. Verbinden Sie das Kabel der LED-Platine mit seinem Anschluss auf der LED-Platine. 4. Bauen Sie folgende Komponenten ein: a. b. c. d. e. 5. Handballenstütze Tastatur Tastaturrahmen Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
4. Führen Sie folgende Schritte durch: a. Entfernen Sie die Schraube, um die Metallhalterung am Stromversorgungsanschluss zu lösen [1] [2]. b. Heben Sie den Stromversorgungsanschluss an und entfernen Sie ihn aus dem Computer [3]. Einbauen des Stromversorgungsanschlusses 1. Bringen Sie den Stromversorgungsanschluss an seiner Position am Computer an. 2.
Entfernen der WLAN-/WiGig-Karte ANMERKUNG: WiGig-Karte ist optional. 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie die Abdeckung an der Unterseite. 3. Führen Sie folgende Schritte durch, um die WLAN-Karte zu entfernen: a. Trennen Sie die WLAN-Kabel von ihren Anschlüssen auf der WLAN-Karte [1]. b. Entfernen Sie die Schraube, mit der die WLAN-Karte am Computer befestigt ist [2]. 4. Entfernen Sie die WLAN-Karte aus dem Computer.
4. Bringen Sie die Abdeckung an der Unterseite an. 5. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der WWAN-Karte 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie die Abdeckung an der Unterseite. 3. Führen Sie folgende Schritte durch, um die WWAN-Karte zu entfernen: a. Trennen Sie die WWAN-Kabel von ihren Anschlüssen auf der WWAN-Karte [1]. b.
4. Bringen Sie die Abdeckung an der Unterseite an. 5. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Bildschirmscharnierhalterungen 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. b. c. d. e. f. g. Bodenabdeckung Akku Speicher Festplattenbaugruppe Tastaturrahmen Tastatur Handballenstütze 3.
Einbauen der Bildschirmscharnierhalterungen 1. Bringen Sie die Bildschirmscharnierhalterungen in ihren Steckplätzen am Computer an. 2. Ziehen Sie die Schrauben auf der Vorder- und der Rückseite des Computers an, um den Bildschirmscharnierhalterungen zu befestigen. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. 4.
4. Trennen Sie das Bildschirmkabel von der Systemplatine. So trennen Sie das Bildschirmkabel: a. Entfernen Sie die Schraube, mit der die Bildschirmkabelhalterung am Computer befestigt ist [1]. b. Entfernen Sie die Bildschirmkabelhalterung, um auf das Bildschirmkabel zugreifen zu können [2]. c. Trennen Sie das Bildschirmkabel von der Systemplatine [3]. 5. 28 Lösen Sie das Bildschirmkabel aus der Kabelführung.
6. Entfernen Sie die Schrauben, mit denen die Bildschirmbaugruppe befestigt ist [1], und heben Sie die Bildschirmbaugruppe an und entfernen Sie sie aus dem Computer [2]. Einsetzen der Bildschirmbaugruppe 1. Platzieren Sie die Bildschirmbaugruppe und richten Sie sie mit den Schraubenhalterungen am Computer aus. 2. Führen Sie das WWAN-, WLAN- und das Bildschirmkabel durch die Kabelführungen. 3. Ziehen Sie die Schrauben fest, um die Bildschirmbaugruppe am Computer zu befestigen. 4.
b. c. d. e. f. 7. Handballenstütze Tastatur Tastaturrahmen Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Bildschirmblende 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Hebeln Sie die Kanten an, um die Bildschirmblende von der Bildschirmbaugruppe zu lösen. 3. Entfernen Sie die Bildschirmblende von der Bildschirmbaugruppe. Einsetzen der Bildschirmblende 1.
3. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen des Bildschirms 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. Bodenabdeckung b. Akku c. Bildschirmblende 3. Entfernen Sie die Schrauben, mit denen der Bildschirm an der Bildschirmbaugruppe befestigt ist [1], heben sie sie an und drehen Sie den Bildschirm um, um auf das eDP-Kabel zugreifen zu können [2]. 4.
Einsetzen des Bildschirms 1. Verbinden Sie das eDP-Kabel mit seinem Anschluss und bringen Sie das Klebeband wieder an. 2. Platzieren Sie den Bildschirm und richten Sie ihn mit den Schraubenhalterungen an der Bildschirmbaugruppe aus. 3. Ziehen Sie die Schrauben fest, um den Bildschirm an der Bildschirmbaugruppe zu befestigen. 4. Bauen Sie folgende Komponenten ein: a. Bildschirmblende b. Akku c. Bodenabdeckung 5.
b. Entfernen Sie die Bildschirmscharniere von der Bildschirmbaugruppe [2]. Einbauen der Bildschirmsscharniere 1. Setzen Sie die Bildschirmscharniere an ihren Steckplätzen an der Bildschirmbaugruppe ein. 2. Ziehen Sie die Schrauben fest, mit denen die Bildschirmscharniere auf beiden Seiten der Bildschirmbaugruppe befestigt sind. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. j. 4.
Einbauen der Kamera 1. Bringen Sie die Kamera an der vorgesehenen Position an der Bildschirmbaugruppe an. 2. Verbinden Sie das Kamerakabel mit dem entsprechenden Anschluss. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. 4. Bildschirm Bildschirmblende Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen des eDP-Kabels 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2.
Einbauen des eDP-Kabels 1. Befestigen Sie das eDP-Kabel an seiner Position an der Bildschirmbaugruppe. 2. Verbinden Sie das eDP-Kabel mit dem entsprechenden Anschluss. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. j. k. 4. Bildschirm Bildschirmblende Bildschirmbaugruppe Bildschirmscharnierhalterungen Handballenstütze Tastatur Tastaturrahmen Festplattenbaugruppe Speicher Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
4. Entfernen Sie den Systemlüfter aus dem Computer. Einsetzen des Systemlüfters 1. Platzieren Sie den Systemlüfter im entsprechenden Steckplatz auf dem Computer. 2. Verbinden Sie das Kabel des Systemlüfters mit dem entsprechenden Anschluss auf der Systemplatine. 3. Bauen Sie folgende Komponenten ein: a. b. c. d. e. 4. Handballenstütze Tastatur Tastaturrahmen Akku Bodenabdeckung Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Audioplatine 1.
a. b. c. d. e. 3. Bodenabdeckung Akku Tastaturrahmen Tastatur Handballenstütze Führen Sie folgende Schritte durch, um die Audioplatine vom Computer zu entfernen: a. b. c. d. Trennen Sie das Kabel der Audioplatine von seinem Anschluss auf der Systemplatine [1] [2]. Lösen Sie das Lautsprecherkabel von der Audioplatine [3]. Entfernen Sie die Schrauben, mit denen die Audioplatine am Computer befestigt ist [4]. Heben Sie die Audioplatine an und entfernen Sie sie aus dem Computer [5].
d. e. f. g. h. i. j. Festplattenbaugruppe Tastaturrahmen Tastatur Handballenstütze Bildschirmscharnierhalterungen Bildschirmbaugruppe Systemlüfter 3. Trennen Sie das Lautsprecherkabel [1] und das Stromversorgungskabel [2] von der Systemplatine. 4. Trennen Sie das Kabel der Audioplatine [1] [2] und entfernen Sie die Schrauben, mit denen die Systemplatine am Computer befestigt ist [3]. 5. Entfernen Sie die Systemplatine aus dem Gehäuse.
Einbauen der Systemplatine 1. Platzieren Sie die Systemplatine und richten Sie sie mit den Schraubenhalterungen am Computer aus. 2. Ziehen Sie die Schrauben fest, um die Systemplatine am Computer zu befestigen. 3. Schließen Sie die folgenden Kabel an ihre jeweiligen Anschlüssen auf der Systemplatine an: a. Audioplatine b. Lautsprecher c. Netzanschluss 4. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. j. 5.
e. f. g. h. i. j. k. 3. Tastaturrahmen Tastatur Handballenstütze Bildschirmscharnierhalterungen Bildschirmbaugruppe Systemlüfter Systemplatine Führen Sie folgende Schritte durch, um die Knopfzellenbatterie aus dem Computer zu entfernen: a. Trennen Sie das Kabel der Knopfzellenbatterie von seinem Anschluss auf der Systemplatine [1]. b. Hebeln Sie die Knopfzellenbatterie an, um sie vom Klebeband zu lösen und entfernen Sie sie von der Systemplatine [2]. Einsetzen der Knopfzellenbatterie 1.
Entfernen des Kühlkörpers 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. b. c. d. e. f. g. h. i. j. 3. Bodenabdeckung Akku Speicher Tastaturrahmen Tastatur Handballenstütze Bildschirmscharnierhalterungen Bildschirmbaugruppe Systemlüfter Systemplatine Führen Sie folgende Schritte durch, um den Kühlkörper von der Systemplatine zu entfernen: a.
i. Speicher j. Akku k. Bodenabdeckung 4. Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers. Entfernen der Lautsprecher 1. Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Innern des Computers. 2. Entfernen Sie folgende Komponenten: a. b. c. d. e. f. g. h. i. j. k. Bodenabdeckung Akku Speicher Festplattenbaugruppe Tastaturrahmen Tastatur Handballenstütze Bildschirmscharnierhalterungen Bildschirmbaugruppe Systemlüfter Systemplatine 3.
Einbauen der Lautsprecher 1. Platzieren Sie die Lautsprecher in ihre Steckplätze auf dem Computer. 2. Ziehen Sie die Schrauben fest, mit denen die Lautsprecher am Computer befestigt werden. 3. Führen Sie die Lautsprecherkabel durch die Kabelführungen. 4. Bauen Sie folgende Komponenten ein: a. b. c. d. e. f. g. h. i. j. k. 5.
Optionen des System-Setup 3 ANMERKUNG: Je nach Computer und installierten Geräten werden die in diesem Abschnitt aufgeführten Elemente möglicherweise gar nicht oder anders als aufgeführt angezeigt. Tabelle 1. Allgemein Option Beschreibung System Information In diesem Abschnitt werden die primären Hardwarefunktionen Ihres Computers beschrieben.
Option Beschreibung deaktivieren oder die Startreihenfolge ändern. Boot List Option Hiermit können Sie die Startlistenoption ändern. • • Legacy UEFI Advanced Boot Options Diese Option bietet Ihnen die Möglichkeit, die Legacy-Option-ROMs zu laden. Standardmäßig ist die Option Enable Legacy Option ROMs (Legacy-Option-ROMs aktivieren) deaktiviert. Date/Time Ermöglicht das Ändern von Datum und Uhrzeit. Tabelle 2.
Option Beschreibung • • • • SMART Reporting Dieses Feld steuert, ob Festplattenfehler für integrierte Laufwerke während des Systemstarts gemeldet werden. Diese Technologie ist Teil der SMART-Spezifikation (Self Monitoring Analysis and Reporting Technology - System zur Selbstüberwachung, Analyse und Statusmeldung). Diese Option ist standardmäßig deaktiviert.
Option Beschreibung Keyboard Backlight with AC Die Option „Keyboard Backlight with AC“ (Tastaturbeleuchtung mit Wechselstrom) wirkt sich nicht auf die eigentliche Tastaturbeleuchtung aus. Die Tastaturbeleuchtung unterstützt auch weiterhin die verschiedenen Beleuchtungsstufen. Dieses Feld hat Einfluss, wenn die Hintergrundbeleuchtung aktiviert ist. Unobtrusive Mode Wenn diese Option aktiviert ist, werden beim Drücken der Tasten Fn+F7 alle Licht- und Tonausgaben im System ausgeschaltet.
Option Beschreibung Standardeinstellung: Not set (Nicht eingestellt) System Password Ermöglicht das Einrichten, Ändern oder Löschen des Systemkennworts. ANMERKUNG: Erfolgreiche Kennwortänderungen werden sofort wirksam. Standardeinstellung: Not set (Nicht eingestellt) Internal HDD-1 Password Ermöglicht das Einrichten, Ändern oder Löschen des Kennworts der internen Festplatte. ANMERKUNG: Erfolgreiche Kennwortänderungen werden sofort wirksam.
Option Beschreibung Standardeinstellung: Die Option ist deaktiviert. Computrace Ermöglicht das Aktivieren oder Deaktivieren der optionalen Computrace-Software. Die Optionen sind: • • • Deactivate (Deaktivieren) Disable (Deaktivieren) Activate (Aktivieren) ANMERKUNG: Mit den Optionen „Activate“ (Aktivieren) und „Disable“ (Deaktivieren) wird die Funktion dauerhaft aktiviert oder deaktiviert. Dann sind keine weiteren Änderungen zulässig.
Option Beschreibung • • db dbx Wenn der benutzerdefinierte Modus aktiviert ist, werden die entsprechenden Optionen für PK, KEK, db und dbx angezeigt. Die Optionen sind: • • • • • • Save to File (In Datei speichern) – Speichert den Schlüssel in einer vom Benutzer ausgewählten Datei. Replace from File (Aus Datei ersetzen) – Ersetzt den aktuellen Schlüssel durch einen Schlüssel aus einer vom Benutzer ausgewählten Datei.
Option Beschreibung Hyper-Thread Control Ermöglicht das Aktivieren oder Deaktivieren von Hyper-Threading im Prozessor. • • Deaktiviert Aktiviert Standardeinstellung: Die Option ist aktiviert. Tabelle 7. Stromverwaltung Option Beschreibung AC Behavior Ermöglicht die Aktivierung oder Deaktivierung des automatischen Einschaltens des Computers, wenn der Netzadapter angeschlossen ist. Standardeinstellung: Wake on AC (Bei Netzanschluss reaktivieren) ist nicht aktiviert.
Option Beschreibung • Block Sleep LAN or WLAN (LAN oder WLAN) Mit dieser Option kann das Eintreten in den Ruhemodus (S3-Modus) in einer Betriebssystemumgebung blockiert werden. Block Sleep (S3 state) (Ruhezustand blockieren (S3-Modus)) – Diese Option ist standardmäßig deaktiviert. Peak Shift Mit dieser Option können Sie den Stromverbrauch während der Spitzenauslastungszeiten minimieren.
Option Beschreibung Standardeinstellung: Enable Adapter Warnings (Netzteilwarnungen aktivieren) Keypad (Embedded) Ermöglicht die Auswahl einer von zwei Methoden zum Aktivieren des numerischen Tastenblocks, der in die interne Tastatur eingebettet ist. • • Fn Key Only (Nur Fn-Taste): Diese Option ist standardmäßig aktiviert. By Numlock (Durch Num-Sperre) ANMERKUNG: Wenn das Setup ausgeführt wird, ist diese Option nicht wirksam. Das Setup funktioniert nur im Modus „Fn Key Only“ (Nur Fn-Taste).
Option Beschreibung • • • 0 seconds (0 Sekunden). Diese Option ist standardmäßig aktiviert. 5 seconds (5 Sekunden) 10 seconds (10 Sekunden) Tabelle 9. Unterstützung der Virtualisierung Option Beschreibung Virtualization Ermöglicht das Aktivieren oder Deaktivieren der Intel Virtualization Technology (Intel-Virtualisierungstechnologie).
Tabelle 11. Wartung Option Beschreibung Service Tag Zeigt die Service-Tag-Nummer des Computers an. Asset Tag Ermöglicht das Erstellen einer Systemkennnummer, wenn diese noch nicht festgelegt wurde. Diese Option ist standardmäßig nicht aktiviert. Tabelle 12. Systemprotokolle Option Beschreibung BIOS Events Ermöglicht das Anzeigen und Löschen von POST-Ereignissen des System-Setup-Programms (BIOS). Thermal Events Ermöglicht das Anzeigen und Löschen der Ereignisse des System-Setup (Temperatur).
4 Technische Daten ANMERKUNG: Die angebotenen Konfigurationen können je nach Region variieren. Um weitere Informationen zur Konfiguration des Computers zu erhalten, klicken Sie auf Start (Start icon) → Help and Support (Hilfe und Support) und wählen Sie dann die Option zur Anzeige der Informationen über Ihren Computer aus. ANMERKUNG: Navigieren Sie in Windows 8.1 zu Help and Support (Hilfe und Support), um Informationen über Ihren Computer anzuzeigen. Tabelle 13.
Funktion Technische Daten Speichertyp DDR3L-SDRAM (1600 MHz) Speicher (Minimum) 4 GB Speicher (Maximum) Intel Prozessoren der 4. Generation 8 GB Intel Prozessoren der 5. Generation 16 GB Tabelle 16. Audio Funktion Technische Daten Typ High-Definition-Audio Controller Realtek ALC3235 Stereo-Konvertierung Digitale Audioausgabe über HDMI – bis zu 7.
Funktion Technische Daten Unterstützung für externe Anzeigen • • 19-poliger HDMI-Anschluss 15-poliger DSUB-VGA-Anschluss Tabelle 18. Kamera Funktionen Technische Daten Kameraauflösung 1280 x 720 Pixel Videoauflösung (Maximum) 1280 x 720 Pixel Diagonaler Betrachtungswinkel 74° Tabelle 19.
Tabelle 22.
Funktion Technische Daten Y-Achse 53,00 mm Tabelle 25.
Tabelle 27.
Diagnostics (Diagnose) 5 Führen Sie bei Problemen mit dem Computer die ePSA-Diagnose durch, bevor Sie Dell zwecks technischer Unterstützung kontaktieren. Der Zweck der Diagnose ist es, die Hardware des Computers ohne zusätzliche Ausrüstung und ohne das Risiko von Datenverlust zu testen. Wenn Sie ein Problem nicht selbst beheben können, können Service- und Supportmitarbeiter die Diagnoseergebnisse zur Lösung des Problems verwenden.
Notieren Sie sich den Fehlercode und wenden Sie sich an Dell. ODER 1. Fahren Sie den Computer herunter. 2. Drücken und halten Sie die Taste und den Betriebsschalter und lassen Sie beide Tasten los. Das Fenster ePSA Pre-boot System Assessment (ePSA-Systemtests vor Hochfahren des Computers) wird angezeigt und listet alle im System erkannte Geräte auf. Die Diagnose beginnt mit der Ausführung der Tests für alle erkannten Geräte. 3.
Speicher-LED Betriebsanz eige-LED Wireless-LED Fehlerbeschreibung Blinkend Blinkend Aus Systemfehler bei der Initialisierung des Festplattenlaufwerks ODER Systemfehler bei der Initialisierung von Option ROM Blinkend Aus Blinkend Während der Initialisierung ist ein USB-ControllerFehler aufgetreten. Stetig Blinkend Blinkend Keine Speichermodule installiert/erkannt. Blinkend Stetig Blinkend Während der Initialisierung des Bildschirms ist ein Problem aufgetreten.
Kontaktaufnahme mit Dell 6 ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit. Da die Verfügbarkeit dieser Optionen je nach Land und Produkt variiert, stehen einige Services in Ihrer Region möglicherweise nicht zur Verfügung.