Manual do Proprietário do Dell Latitude E6320 Modelo regulamentar P12S Tipo regulamentar P12S001
Notas, avisos e advertências NOTA: Uma NOTA indica informações importantes para melhor utilizar o computador. AVISO: Um AVISO alerta para a possibilidade de danos no hardware ou de perda de dados, caso as instruções não sejam seguidas. ADVERTÊNCIA: Uma ADVERTÊNCIA indica potenciais danos no equipamento, lesões corporais ou mesmo morte. As informações deste documento estão sujeitas a alteração sem aviso prévio. © 2011 Dell Inc. Todos os direitos reservados.
Índice Notas, avisos e advertências......................................................................2 Capítulo 1: Trabalhar no computador........................................................9 Antes de efectuar qualquer procedimento no interior do computador............................9 Ferramentas recomendadas...........................................................................................11 Desligar o computador..............................................................................
Instalar a unidade óptica................................................................................................25 Capítulo 8: Tampa da base.........................................................................27 Remover a tampa da base...............................................................................................27 Instalar a tampa da base.................................................................................................28 Capítulo 9: Cartão de memória...........
Capítulo 16: Placa Bluetooth.....................................................................47 Retirar a placa Bluetooth................................................................................................47 Instalar a placa Bluetooth...............................................................................................48 Capítulo 17: Placa de LEDs........................................................................49 Retirar a placa de LEDs.......................................
Instalar o painel de entrada/saída..................................................................................81 Capítulo 25: Altifalante................................................................................83 Retirar os altifalantes......................................................................................................83 Instalar os altifalantes.....................................................................................................85 Capítulo 26: Porta DC-in....
Capítulo 33: Contactar a Dell...................................................................121 Contactar a Dell.............................................................................................................
Trabalhar no computador 1 Antes de efectuar qualquer procedimento no interior do computador Utilize as seguintes directrizes de segurança para ajudar a proteger o computador de potenciais danos, e para ajudar a assegurar a sua segurança pessoal. Salvo indicação em contrário, cada procedimento neste documento pressupõe a existência das seguintes condições: • • • Efectuou os passos indicados em Trabalhar no Computador. Leu as informações de segurança fornecidas com o computador.
AVISO: Quando desligar um cabo, puxe pelo respectivo conector ou pela patilha e não pelo próprio cabo. Alguns cabos possuem conectores com patilhas de bloqueio. Se estiver a desligar este tipo de cabo, prima as patilhas de bloqueio antes de desligar o cabo. À medida que puxa os conectores, mantenha-os alinhados para evitar que os pinos do conector dobrem. Do mesmo modo, antes de ligar um cabo, certifique-se de ambos os conectores estão correctamente orientados e alinhados.
AVISO: Antes de tocar em qualquer parte interior do computador, ligue-se à terra tocando numa superfície metálica não pintada, tal como o metal na parte posterior do computador. Enquanto trabalha, toque periodicamente numa superfície metálica não pintada para dissipar a electricidade estática, uma vez que esta pode danificar os componentes internos. 11. Retire qualquer ExpressCard ou Smart Card instalada das respectivas ranhuras.
operativo, mantenha premido o botão de alimentação durante cerca de 4 segundos para os desligar. Após efectuar qualquer procedimento no interior do computador Uma vez concluído o procedimento de reposição de componente, certifique-se de que liga os dispositivos externos, placas e cabos antes de ligar o computador. AVISO: Para evitar danos no computador, utilize apenas a bateria designada para este computador Dell. Não utilize baterias específicas de outros computadores Dell. 1. 2.
ExpressCard 2 Retirar a ExpressCard 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Prima a ExpressCard para a libertar do computador. 3. Faça deslizar a ExpressCard para fora do computador. Instalar a ExpressCard 1. Deslize a ExpressCard para dentro da ranhura até encaixar no local. 2. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Cartão SD (Secure Digital) 3 Retirar o cartão SD (Secure Digital) 2. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Prima o cartão SD para soltá-lo do computador. 3. Deslize o cartão SD para fora do computador. 1.
Instalar o cartão SD (Secure Digital) 1. 2. 16 Deslize o cartão SD (Secure Digital) para dentro da ranhura até que encaixe no local. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Bateria 4 Retirar a bateria 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Deslize os trincos de desbloqueio para libertar a bateria. 3. Deslize a bateria para fora e retire-a do computador. Instalar a bateria 1. Deslize a bateria para a respectiva ranhura até que encaixe no local. 2. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Cartão SIM (Subscriber Identity Module) 5 Retirar o cartão SIM (Subscriber Identity Module) 2. 3. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Retire a bateria. Prima o cartão SIM para o libertar do computador. 4. Deslize o cartão SIM do computador. 1.
Instalar o cartão SIM (Subscriber Identity Module) 1. 2. 3. 20 Deslize o cartão SIM para o respectivo compartimento. Instale a bateria. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Unidade de disco rígido 6 Retirar a unidade de disco rígido 2. 3. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Retire a bateria. Retire os parafusos que fixam a unidade de disco rígido ao computador. 4. Deslizar e retire a unidade de disco rígido do computador. 5. Retire o parafuso que fixa o suporte da unidade de disco rígido na respectiva unidade. 1.
6. Puxe e retire o suporte da unidade de disco rígido da respectiva unidade. Instalar a unidade de disco rígido 1. 2. 3. 4. 5. 6. 22 Instale o suporte da unidade de disco rígido à unidade. Aperte os parafusos para fixar o suporte da unidade de disco rígido na unidade. Deslize a unidade de disco rígido para o computador. Volte a colocar e aperte os parafusos que fixam a unidade de disco rígido ao computador. Instale a bateria.
Unidade óptica 7 Retirar a unidade óptica 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Prima e solte o trinco da unidade óptica. 3. Deslize a unidade óptica para fora do computador. 4. Puxe a porta da unidade óptica a partir de um lado para a soltar.
5. Puxe o outro lado da porta da unidade óptica para soltá-la completamente da unidade óptica. 6. Retire o parafuso que fixa o trinco à unidade óptica. 7. Retire o trinco da unidade óptica. 8. Retire os parafusos que fixam o suporte do trinco à unidade óptica.
9. Retire o suporte do trinco da unidade óptica. Instalar a unidade óptica 1. Insira o suporte do trinco da unidade na unidade óptica. 2. Aperte os parafusos para fixar o suporte do trinco da unidade na unidade óptica. 3. Insira o trinco da unidade na unidade óptica. 4. Aperte o parafuso para fixar o trinco da unidade na unidade óptica. 5. Prima a porta da unidade óptica para inseri-la completamente na unidade óptica. 6.
Tampa da base 8 Remover a tampa da base 2. 3. 4. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Retire a bateria. Retire o cartão SD (Secure Digital). Retire os parafusos que fixam a tampa da base ao computador. 5. Levante a tampa da base e retire-a do computador. 1.
Instalar a tampa da base 1. 2. 3. 4. 28 Coloque a tampa da base para alinhar os orifícios dos parafusos correctamente com o computador. Volte a colocar e aperte os parafusos para fixar a tampa da base no computador. Instalar o cartão SD (Secure Digital). Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Cartão de memória 9 Retirar a memória 2. 3. 4. 5. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Retire a bateria. Retire o cartão SD (Secure Digital). Retire a tampa da base. Levante os grampos de retenção do módulo de memória até ele se soltar. 6. Retire o módulo de memória do computador. 1.
Instalar a memória 1. 2. 3. Insira o módulo de memória na respectiva ranhura. Prima os grampos para fixar o módulo de memória na placa de sistema. Instale a tampa da base. 4. 5. 6. Instale o cartão SD (Secure Digital). Instale a bateria Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Bateria de célula tipo moeda 10 Retirar a bateria de célula tipo moeda 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a tampa da base. 5. Desligue o cabo da bateria de célula tipo moeda da placa de sistema. 6. Solte e retire a bateria de célula tipo moeda do computador.
Instalar a bateria de célula tipo moeda 1. Coloque a bateria de célula tipo moeda no respectivo local. 2. 3. 4. 5. 6. Ligue o cabo da bateria tipo moeda à placa de sistema. Instale a tampa da base. Instale o cartão SD (Secure Digital). Instale a bateria Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Placa de rede local sem fios (WLAN) 11 Retirar a placa de rede de área local sem fios (WLAN) 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a tampa da base. 5. Desligue os cabos de antena da placa WLAN. 6. Retire o parafuso que fixa a placa WLAN à placa de sistema.
7. Retire a placa WLAN da respectiva ranhura na placa de sistema. Instalar a placa de rede local sem fios (WLAN) 1. 2. 3. 4. 5. 6. 7. 34 Insira a placa WLAN no conector com um ângulo de 45 graus. Volte a colocar e aperte o parafuso que fixa a placa WLAN ao computador. Ligue os cabos das antenas de acordo com o código de cores na placa WLAN. Instale a tampa da base. Instale o cartão SD (Secure Digital).
Placa de rede de área alargada sem fios (WWAN) 12 Retirar a placa de rede de área alargada sem fios (WWAN) 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a tampa da base. 5. Desligue os cabos de antena da placa WWAN. 6. Retire o parafuso que fixa a placa WWAN ao computador.
7. Retire a placa WWAN do computador. Instalar a placa de rede de área alargada sem fios (WWAN) 1. 2. 3. 4. 5. 6. 7. 36 Insira a placa WWAN no respectivo conector, com um ângulo de 45 graus. Recoloque e aperte o parafuso para fixar a placa WWAN ao computador. Ligue os cabos das antenas de acordo com o código de cores na placa WLAN. Instale a tampa da base. Instale o cartão SD (Secure Digital).
Borda do teclado 13 Retirar a borda do teclado 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Utilizando um instrumento aguçado, levante a borda do teclado para soltá-lo do computador. 3. Levante a borda do teclado para soltar as patilhas e retire-o do computador.
Instalar a borda do teclado 1. Alinhe a borda com o respectivo teclado e encaixe no lugar. 2. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Teclado 14 Retirar o teclado 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire a borda do teclado. 4. Retire os parafusos que fixam o teclado ao computador. 5. Retire os parafusos que fixam o teclado ao conjunto do apoio de mãos. 6. Volte o teclado e coloque voltado para o ecrã.
7. Levante o grampo para libertar o cabo do teclado e desligue do computador. 8. Retire o teclado do computador.
9. Retire a fita de fixação do cabo do teclado. 10. Desligue e retire o cabo do teclado. Instalar o teclado 1. Ligue o cabo do teclado e fixe-o utilizando a fita. 2. Ligue o cabo do teclado ao respectivo conector na placa de sistema. 3. Vire o teclado ao contrário e coloque-o sobre o apoio de mãos. 4. Recoloque e aperte os parafusos para fixar o teclado no conjunto do apoio de mãos. 5. Recoloque e aperte os parafusos para fixar o teclado no computador. 6. Instale a bateria. 7.
Apoio para mãos 15 Retirar o conjunto do apoio de mãos 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire os parafusos que fixam o conjunto do apoio de mãos ao computador. 11.
12. Retire os parafusos para libertar o conjunto do apoio de mãos da placa de sistema. 13. Levante o conjunto do apoio de mãos ao longo das bordas para desbloquear as patilhas, e retire-o do computador.
Instalar o conjunto do apoio de mãos 1. 2. 3. Alinhe o conjunto do apoio de mãos com o computador e encaixe-o no lugar. Volte a colocar e aperte os parafusos para fixar o conjunto do apoio de mãos na placa de sistema.
• leitor de impressões digitais Volte a colocar e aperte os parafusos para fixar o conjunto do apoio de mãos no computador. 5. Instale o teclado. 6. Instale a borda do teclado. 7. Instale a unidade de disco rígido. 8. Instale a ExpressCard. 9. Instale a tampa da base. 10. Instale a unidade óptica. 11. Instale o cartão SD (Secure Digital). 4. 12. Instale a bateria. 13. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Placa Bluetooth 16 Retirar a placa Bluetooth 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11.
13. Solte e retire o cabo Bluetooth da respectiva placa. Instalar a placa Bluetooth 1. Ligue o cabo de Bluetooth à respectiva placa. 2. Coloque a placa Bluetooth no conjunto do apoio de mãos. 3. Volte a colocar e aperte o parafuso para fixar a placa Bluetooth no conjunto do apoio de mãos. 4. Instale o conjunto do apoio de mãos. 5. Instale o teclado. 6. Instale a borda do teclado. 7. Instale a unidade de disco rígido. 8. Instale a ExpressCard. 9. Instale a tampa da base. 10.
Placa de LEDs 17 Retirar a placa de LEDs 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11. Solte o cabo da placa de LEDs do canal de disposição. 12.
13. Retire a placa de LEDs do conjunto do apoio de mãos.
Instalar a placa de LEDs 1. Alinhe a placa de LEDs no apoio de mãos. 2. Volte a colocar e aperte o parafuso que fixa a placa de LEDs ao apoio de mãos. Coloque o cabo da placa de LEDs na posição original. Instale o conjunto do apoio de mãos. Instale o teclado. Instale a borda do teclado. Instale a unidade de disco rígido. Instale a ExpressCard. Instale a tampa da base. Instale a unidade óptica. Instale o cartão SD (Secure Digital). Instale a bateria.
Leitor de cartões Smart Card 18 Remover o leitor de Smart Card 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11.
13. Levante e retire o leitor de Smart Card do computador.
Instalar o leitor de cartões de Smart Card 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Coloque o leitor de cartões de Smart Card na posição original no computador. Volte a colocar e aperte os parafusos para fixar o leitor de Smart Card no computador. Ligue o cabo do leitor de Smart Card à placa de sistema. Volte a colocar e aperte os parafusos para fixar o conjunto do apoio de mãos no computador. Instale o conjunto do apoio de mãos. Instale o teclado. Instale a borda do teclado.
Placa multimédia 19 Retirar a placa multimédia 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11. Desligue o cabo da placa multimédia da placa de sistema. 12.
13. Retire a placa multimédia do computador.
Instalar a placa multimédia 1. Alinhe a placa multimédia na posição original no computador. 2. Volte a colocar e aperte os parafusos para fixar a placa multimédia ao computador. Ligue o cabo da placa multimédia à placa de sistema. Instale o conjunto do apoio de mãos. Instale o teclado. Instale a borda do teclado. Instale a unidade de disco rígido. Instale a ExpressCard. Instale a tampa da base. Instale a unidade óptica. Instale o cartão SD (Secure Digital). Instale a bateria.
Dobradiças do ecrã 20 Retirar as protecções das dobradiças do ecrã 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11.
Instalar as protecções das dobradiças do ecrã 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 62 Coloque as dobradiças do ecrã nas posições apropriadas. Recoloque e aperte os parafusos para fixar as protecções das dobradiças do ecrã ao computador. Instale o conjunto do apoio de mãos. Instale o teclado. Instale a borda do teclado. Instale a unidade de disco rígido. Instale a ExpressCard. Instale a tampa da base. Instale a unidade óptica. Instale o cartão SD (Secure Digital). Instale a bateria.
Conjunto do ecrã 21 Retirar o conjunto do ecrã 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire a tampa da base. 6. Retire a ExpressCard. 7. Retire a unidade de disco rígido. 8. Retire a borda do teclado. 9. Retire o teclado. 10. Retire o conjunto do apoio de mãos. 11. Retire as protecções das dobradiças do ecrã. 12.
14. Puxar os cabos de antena dos respectivos canais de encaminhamento? 15. Retire os parafusos que fixam o suporte do cabo do ecrã na placa de sistema.
16. Retire o suporte do cabo do ecrã do computador. 17. Puxe o cabo do ecrã para o desligar da placa de sistema. 18. Retire o parafuso que fixa o conjunto do ecrã ao computador.
19. Retire o conjunto do ecrã do computador.
Instalar o conjunto do ecrã 1. Alinhe o conjunto do ecrã na posição original no computador. 2. Volte a colocar e aperte o parafuso para fixar o conjunto do ecrã ao computador. 3. Volte a colocar e ligue o cabo do ecrã à placa de sistema. 4. Alinhe o suporte do cabo ecrã na posição original. 5. Volte a colocar e aperte os parafusos para fixar o suporte do cabo do ecrã à placa de sistema. 6. Disponha os cabos de antena através da placa de sistema. 7.
Placa de sistema 22 Retirar a placa de sistema 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire o cartão SIM (Subscriber Identity Module). 6. Retire a tampa da base. 7. Retire a ExpressCard. 8. Retire a unidade de disco rígido. 9. Retire a borda do teclado. 10. Retire o teclado. 11. Retire a placa de rede de área local sem fios (WLAN).
19. Retire os parafusos que fixam a placa de sistema ao computador. 20. Levante a placa de sistema para localizar o cabo da fonte de alimentação. 21. Desligue da placa de sistema o cabo da fonte de alimentação.
22. Levante a placa de sistema e retire-a do computador. NOTA: Os passos 23 e 24 são aplicáveis a computadores fornecidos nos Estados Unidos da América. 23. Volte o sistema e retire o parafuso que fixa a placa TAA.
24. Retire do sistema a placa TAA. Instalar a placa de sistema 1. 72 Coloque a placa TAA na posição original.
NOTA: Os passos 1 e 2 são aplicáveis aos computadores fornecidos nos Estados Unidos da América. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Volte a colocar e aperte o parafuso para fixar a placa TAA no computador. Alinhe a placa de sistema na posição original no computador. Ligue o cabo de alimentação. Volte a colocar e aperte os parafusos para fixar a placa de sistema no computador. Disponha e ligue os cabos da Smart Card e do altifalante na placa de sistema. Instale o conjunto do ecrã.
Dissipador de calor 23 Retirar o conjunto do dissipador de calor 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire o cartão SIM (Subscriber Identity Module). 6. Retire a tampa da base. 7. Retire a ExpressCard. 8. Retire a unidade de disco rígido. 9. Retire a borda do teclado. 10. Retire o teclado. 11.
20. Desaperte os parafusos que fixam o conjunto do dissipador de calor à placa de sistema. 21. Retire o conjunto do dissipador de calor da placa de sistema.
Instalar o conjunto do dissipador de calor 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Alinhe o conjunto do dissipador de calor na posição original na placa de sistema. Aperte os parafusos para fixar o conjunto do dissipador de calor à placa de sistema. Ligue o cabo do dissipador de calor à placa de sistema. Instale o conjunto do dissipador de calor. Instale o conjunto do ecrã. Instale as protecções das dobradiças do ecrã. Instale o conjunto do apoio de mãos. Instale o teclado.
Painel de entrada/saída 24 Retirar o painel de entrada/saída 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire o cartão SIM (Subscriber Identity Module). 6. Retire a tampa da base. 7. Retire a ExpressCard. 8. Retire a unidade de disco rígido. 9. Retire a borda do teclado. 10. Retire o teclado. 11.
19. Retire o painel de E/S do computador.
Instalar o painel de entrada/saída 1. Volte a colocar o painel de E/S no computador. 2. 3. 4. 5. 6. 7. Aperte o parafuso que fixa o painel de E/S ao computador. Instale o conjunto do ecrã. Instale as protecções das dobradiças do ecrã. Instale o conjunto do apoio de mão. Instale o teclado. Instale a borda do teclado. 8. 9. 10. 11. 12. 13. 14. Instale a unidade de disco rígido. Instale a ExpressCard. Instale a tampa da base. Instale a unidade óptica. Instale o cartão SD (Secure Digital).
Altifalante 25 Retirar os altifalantes 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire a tampa da base. 4. Retire o cartão SD (Secure Digital). 5. Retire a unidade óptica. 6. Retire o cartão SIM (Subscriber Identity Module). 7. Retire a ExpressCard. 8. Retire a unidade de disco rígido. 9. Retire a borda do teclado. 10. Retire o teclado. 11. Retire a placa de rede de área local sem fios (WLAN). 12.
20. Retire os parafusos que fixam os altifalantes ao computador. 21. Retire os altifalantes do computador.
Instalar os altifalantes 1. Recoloque os altifalantes na respectiva posição original no computador. 2. Aperte os parafusos que fixam os altifalantes do computador. 3. Encaminhe e ligue o cabo do altifalante. 4. Instale a placa de sistema 5. Instale o conjunto do ecrã. 6. Instale as protecções das dobradiças do ecrã. 7. Instale o conjunto do apoio de mãos. 8. Instale a bateria tipo moeda. 9. Instale a placa de rede de área local sem fios (WLAN) 10.
Porta DC-in 26 Retirar a porta DC-In 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no computador. 2. Retire a bateria. 3. Retire o cartão SD (Secure Digital). 4. Retire a unidade óptica. 5. Retire o cartão SIM (Subscriber Identity Module). 6. Retire a tampa da base. 7. Retire a ExpressCard. 8. Retire a unidade de disco rígido. 9. Retire a borda do teclado. 10. Retire o teclado. 11. Retire a placa de rede de área local sem fios (WLAN). 12.
20. Retire o suporte de DC-In do sistema. 21. Retire a porta de DC-In do sistema.
Instalar a porta DC-In 1. Recoloque a porta DC-In na respectiva posição original no computador. 2. Recoloque o suporte DC-In na respectiva posição original no computador. 3. Aperte o parafuso para fixar o suporte DC-In no computador. 4. Instale a placa de sistema 5. Instale o conjunto do ecrã. 6. Instale as protecções das dobradiças do ecrã. 7. Instale o conjunto do apoio de mãos. 8. Instale a placa multimédia 9. Instale a placa de rede de área local sem fios (WLAN) 10.
Moldura do ecrã 27 Retirar a moldura do ecrã 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Começando a partir de baixo, levante a moldura a partir da parte interior do conjunto do ecrã. 4. Retire a moldura do conjunto do ecrã.
Instalar a moldura do ecrã 1. Coloque a moldura no conjunto do ecrã. 2. 3. 4. 5. Trabalhe ao longo das extremidades superior e inferior da moldura do ecrã. Prima as extremidades esquerda e direita da moldura do ecrã. Instale a bateria. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
Painel do ecrã 28 Retirar o painel do ecrã 1. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. 2. Retire a bateria. 3. Retire a moldura do ecrã. 4. Retire os parafusos que fixam o painel do ecrã no conjunto do ecrã. 5. Vire o painel do ecrã ao contrário.
6. Desligue o cabo de sinal diferencial de baixa voltagem (LVDS) do painel do ecrã. 7. Retire o painel do ecrã do conjunto do ecrã. Instalar o painel do ecrã 1. Alinhe o painel do ecrã na posição original do conjunto do ecrã. 2. Ligue o cabo de sinalização diferencial de baixa tensão (LVDS) ao painel do ecrã. 3. Aperte os parafusos para fixar o painel do ecrã ao conjunto do ecrã. 4. Instale a moldura do ecrã 5. Instale a bateria 6.
Câmara 29 Retirar a câmara 2. 3. 4. 5. Siga os procedimentos indicados em Antes de efectuar qualquer procedimento no interior do computador. Retire a bateria. Retire a moldura do ecrã. Retire o painel do ecrã. Desligue o cabo do módulo da câmara. 6. Retire o parafuso que fixa a câmara e o microfone no conjunto do ecrã. 1.
7. Retire a câmara do conjunto do ecrã. Instalar a câmara 1. Coloque o módulo da câmara na posição original no conjunto do ecrã. 2. Aperte o parafuso que fixa a câmara ao conjunto do ecrã. 3. Ligue o cabo da câmara ao módulo. 4. Instale o painel do ecrã. 5. Instale o bisel do ecrã. 6. Instale a bateria. 7. Siga os procedimentos indicados em Após efectuar qualquer procedimento no interior do computador.
30 Especificações Especificações técnicas NOTA: As ofertas podem variar consoante a região. Nas especificações a seguir, são apresentadas apenas aquelas consideradas obrigatórias por lei para serem fornecidas com o seu computador. Para obter mais informações acerca da configuração do seu computador, clique em Iniciar → Ajuda e Suporte e seleccione a opção para mostrar as informações sobre o seu computador.
Áudio Tipo Áudio de alta definição de quatro canais Controlador IDT 92HD90 Conversão de estéreo 24 bits (analógico para digital e digital para analógico) Interface: Interna áudio de alta definição Externa Conector de entrada do microfone/ auscultadores estéreo/colunas externas Altifalantes dois Amplificador de colunas interno 0,5 W (típico) por canal Controlos de volume teclas de função do teclado, menus do programa Vídeo Tipo integrado na placa de sistema Controlador Intel HD Graphics C
Portas e conectores Leitor de cartões de memória Um leitor de cartões de memória 5 em 1 Smart Card sem contacto Tecnologias/Smart Cards suportados ISO14443A — 106 kbps, 212 kbps, 424 kbps e 848 kbps ISO14443B — 106 kbps, 212 kbps, 424 kbps e 848 kbps ISO15693 HID iClass FIPS201 NXP Desfire Ecrã Tipo díodo emissor de luz branca (WLED) Tamanho 13,3 pol.
Painel táctil Área activa: Eixo X 80,00 mm Eixo Y 40,70 mm Bateria Tipo • • • Bateria de iões de lítio com ExpressCharge (30 Wh) de 3 células Bateria de iões de lítio com ExpressCharge (60 Wh) de 6 células Bateria de iões de lítio (58Wh) de 6 células Dimensões: 3 células Profundidade 29,97 mm Altura 19,80 mm Largura 208,00 mm 6 células Profundidade 54,10 mm Altura 20,85 mm Largura 214,00 mm Peso: 3 células 177,00 g 6 células 349,00 g Tempo de carregamento com o computador desligado: 3
Bateria Desligado Bateria de célula tipo moeda –40 °C a 65 °C Célula de lítio tipo moeda CR2032 de 3 V Adaptador de CA Tipo 65 W e 90 W Tensão de entrada 100 VCA a 240 VCA Corrente de entrada (máxima) 1,50 A/1,60 A/1,70 A Frequência de entrada 50 Hz a 60 Hz Potência de saída 65 W e 90 W Corrente de saída 3,34 A e 4,62 A (contínua) Tensão de saída nominal 19,5 +/– 1,0 VCC Amplitude térmica: Em funcionamento 0 °C a 40 °C Desligado –40 °C a 70 °C Características físicas Altura 25,40 mm a 3
Características ambientais Armazenamento 5% a 95% (sem condensação) Altitude (máxima): Em funcionamento –15,24 m a 3048 m Desligado –15,24 m a 10.668 m Nível de contaminação pelo ar 102 G1, conforme definido pela norma ISA-S71.
Configuração do sistema 31 Descrição geral A Configuração do Sistema permite-lhe: • • • alterar as informações de configuração do sistema depois de adicionar, alterar ou remover qualquer hardware no seu computador; definir ou alterar uma opção seleccionável pelo utilizador, tal como a palavra-passe do utilizador; ler a quantidade de memória actual ou definir o tipo de unidade de disco rígido instalado.
General (Geral) Opção Descrição Informação sobre o sistema Esta secção lista as principais funcionalidades de hardware do seu computador. • • • • Informação sobre o sistema Memory Information (Informações da memória) Processor Information (Informações do processador) Device Information (Informações de dispositivos) Battery Information (Informações sobre a bateria) Apresenta o estado da bateria e o tipo de adaptador CA ligado ao computador.
System Configuration (Configuração do sistema) Opção Descrição NOTA: A Configuração do sistema contém opções e definições relacionadas com os dispositivos de sistema integrados. Dependendo do computador e dos dispositivos instalados, os itens listados nesta secção podem, ou não, aparecer. Integrated NIC (NIC integrado) Permite-lhe activar ou desactivar o controlador de rede integrado.
Opção Descrição SATA Operation (Operação de SATA) Permite configurar o controlador da unidade de disco rígido SATA. As opções são: • • • • Disabled (Desactivado) ATA AHCI RAID On (RAID ligado) Predefinição: RAID On (RAID ligado) NOTA: SATA é configurada para suportar o modo RAID. USB Controller (Controlador USB) Permite controlar o controlador USB.
Opção Descrição • Câmara Também pode activar ou desactivar a placa multimédia e 1394 em conjunto. Predefinição: todos os dispositivos estão activados. Keyboard illumination (Iluminação do teclado) Permite configurar a funcionalidade de iluminação do teclado.
Opção Descrição NOTA: Antes de definir a palavra-passe de sistema ou de disco rígido, deverá definir a palavra-passe de administrador. NOTA: As alterações bem sucedidas da palavra-passe têm efeito imediato. NOTA: Se eliminar a palavra-passe de administrador, as palavras-passe de sistema e da unidade de disco rígido também serão eliminadas. NOTA: As alterações bem sucedidas da palavra-passe têm efeito imediato.
Opção Descrição palavra-passe de administrador está definida. Predefinição: a opção Allow Non-Admin Password Changes (Permitir alterações de palavra-passe não de administrador) está seleccionada Strong Password (Palavra-passe segura) Permite forçar a opção de definir sempre palavras-passe seguras. Predefinição: a opção Enable Stron Password (Activar palavra-passe segura) não está seleccionada.
Opção Descrição Predefinição: A opção Enable CPU XD Support (Activar suporte de CPU XD) está seleccionada. Non-Admin Setup Changes (Alterações à configuração não de administrador) Permite determinar se são permitidas alterações às opções de configuração quando está definida uma palavra-passe de administrador. Se desactivada, as opções de configuração ficam bloqueada pela palavra-passe de administrador.
Opção Descrição C States Control (Controlo C States) Permite activar ou desactivar os estados adicionais de pausa do processador. Predefinição: As opções C states (Estados C), C3, C6, Enhanced C-states (Estados C melhorados) e C7 estão seleccionadas/ activadas. Limit CPUID (Limite do CPUID) Permite limitar o valor máximo suportado pela função CPUID padrão do processador. Predefinição: A opção Enable Intel CPUID (Activar Intel SpeedStep) está seleccionada.
Opção Descrição USB Wake Support (Suporte para activação por USB) Permite activar os dispositivos USB para reactivar o sistema do modo de espera. Predefinição: A opção Enable USB Wake Support (Activar suporte de activação de USB) não está seleccionada. NOTA: Esta função só é funcional quando o adaptador de corrente CA está ligado. Se o adaptador de corrente CA for removido durante o modo de espera, a configuração do sistema retirará energia de todas as portas USB para conservar a carga da bateria.
POST Behavior (Comportamento POST) Opção Descrição Adapter Warnings (Avisos do adaptador) Permite-lhe activar ou desactivar as mensagens de aviso da configuração do sistema (BIOS) quando utilizar determinados adaptadores de corrente. Predefinição: A opção Enable Adapter Warnings (Activar advertências do adaptador) está seleccionada. Teclado numérico (integrado) Permite-lhe escolher um ou dois métodos para activar o teclado numérico que está integrado no teclado interno.
Opção Descrição indicando a sequência de combinações de teclas para aceder ao menu de opções da Configuração do Sistema Sistema. Predefinição:A opção Enable F12 Boot Option Menu (Activar menu de opções de arranque F12) está seleccionada). Fastboot (Arranque rápido) Permite definir a opção para acelerar o processo de arranque.
Opção Descrição Predefinição: todas as opções estão seleccionadas. Wireless Device Enable (Activação de dispositivos sem fios) Permite-lhe activar ou desactivar os dispositivos sem fios. Predefinição: todas as opções estão seleccionadas. Maintenance (Manutenção) Opção Descrição Service Tag (Etiqueta de serviço) Apresenta a etiqueta de serviço do computador. Asset Tag (Etiqueta de inventário) Apresenta a etiqueta de identificação do activo.
32 Diagnóstico Luzes de estado do dispositivo Acende ao ligar o computador e fica intermitente quando o computador se encontrar no modo de gestão de energia. Acende quando o computador lê ou grava dados. Acende fixa ou fica intermitente para indicar o estado de carga da bateria. Acende quando é activado o funcionamento em rede sem fios.
Aspecto Descrição Inter mitent e Fixo Fixo Erro do processador Fixo Inter miten te Fixo A memória foi detectada mas tem erros Passo seguinte Volte a colocar a placa de sistema. 1. Reinstale a memória. 2. Se estiverem instalados dois módulos, remova um e teste. Tente o outro módulo na mesma ranhura e teste. Teste a outra ranhura com ambos os módulos. 3. Volte a colocar a memória. 4. Volte a colocar a placa de sistema. Inter Inter Inter Erro da placa de Volte a colocar a placa de sistema.
Aspecto Inter mitent e Fixo Descrição Inter Erro do painel do miten ecrã te Apag Inter Inter Erro do modem ada miten miten te te Passo seguinte 1. Reinstale o cabo do ecrã. 2. Volte a colocar o painel do ecrã. 3. Volte a colocar o cabo de vídeo/placa de sistema. 1. Reinstale o modem. 2. Substitua o modem. 3. Volte a colocar a placa de sistema.
Contactar a Dell 33 Contactar a Dell NOTA: Se não tiver uma ligação activa à Internet, pode encontrar as informações de contacto na sua factura, na nota de encomenda ou no catálogo de produtos Dell. A Dell disponibiliza várias opções de serviço e suporte online e através de telefone. A disponibilidade varia de acordo com o país e produto, e alguns serviços podem não estar disponíveis na sua área. Para contactar a Dell relativamente a vendas, suporte técnico ou apoio a clientes: 1. 2. 3. 4.