Dell Latitude E6320-brukermanual Forskriftsmessig modell P12S Forskriftmessig type P12S001
Merknader, forholdsregler og advarsler MERK: En MERKNAD angir viktig informasjon som hjelper deg med å bruke datamaskinen bedre. FORSIKTIG: En FORHOLDSREGEL angir potensiell fare for maskinvaren eller tap av data hvis du ikke følger instruksjonene. ADVARSEL: En ADVARSEL angir potensiell fare for skade på eiendom, personskade eller død. Informasjonen i dette dokumentet kan endres uten varsel. © 2011 Dell Inc. Med enerett.
Innholdsfortegnelse Merknader, forholdsregler og advarsler...................................................2 Kapittel 1: Arbeide inne i datamaskinen....................................................9 Gjør følgende før du foretar arbeid inne i datamaskinen:.................................................9 Anbefalte verktøy............................................................................................................10 Slå av datamaskinen......................................................
Sette inn den optiske stasjonen......................................................................................25 Kapittel 8: Hoveddeksel..............................................................................27 Ta av bunndekslet...........................................................................................................27 Sette på bunndekslet.......................................................................................................28 Kapittel 9: Minnekort............
Kapittel 16: Bluetooth-kort.........................................................................47 Ta ut Bluetooth-kortet.....................................................................................................47 Sette inn Bluetooth-kortet...............................................................................................48 Kapittel 17: LED-kort....................................................................................49 Removing The LED Board............................
Sette på inn- og utgangspanelet.....................................................................................79 Kapittel 25: Høyttaler...................................................................................81 Ta av høyttalerne.............................................................................................................81 Sette på høyttalerne........................................................................................................
Kapittel 33: Kontakte Dell.........................................................................117 kontakte Dell..................................................................................................................
Arbeide inne i datamaskinen 1 Gjør følgende før du foretar arbeid inne i datamaskinen: Følg disse sikkerhetsreglene for å beskytte datamaskinen mot mulig skade og bidra til din egen sikkerhet. Hvis ikke annet er anmerket, forutsetter hver av prosedyrene i dette dokumentet følgende: • • • Du har utført trinnene i Arbeide på datamaskinen. Du har lest sikkerhetsanvisningene som fulgte med datamaskinen.
MERK: Fargen på datamaskinen og enkelte komponenter kan se annerledes ut enn i dette dokumentet. For å unngå å skade datamaskinen må du utføre trinnene nedenfor før du begynner å arbeide inne i datamaskinen. 1. Pass på at arbeidsunderlaget er plant og rent, slik at du unngår riper i datamaskindekselet. 2. Slå av datamaskinen (se Slå av datamaskinen). 3. Hvis datamaskinen er koblet til en forankringsenhet, for eksempel mediebasen eller batterimodulen, kobler du dette fra.
• • Liten plasspiss CD med BIOS-oppdateringsprogram Slå av datamaskinen FORSIKTIG: Lagre og lukk alle åpne filer og avslutt åpne programmer før du slår av datamaskinen så du unngår å miste data. 1. Slå av operativsystemet: • I Windows Vista: , og klikk deretter på pilen nederst til høyre på StartKlikk på Start menyen som vist nedenfor og deretter på Slå av. • 2. I Windows XP: Klikk Start → Slå av datamaskinen → Slå av .
ExpressCard 2 Ta ut ExpressCard-kortet 1. 2. Følg fremgangsmåten i Før du arbeider på datamaskinen. Trykk på ExpressCard-kortet for å løsne det fra datamaskinen. 3. Skyv kortet ut av datamaskinen. Sette inn ExpressCard-kortet 1. 2. Skyv ExpressCard-kortet inn i sporet til det klikker på plass. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Secure Digital-kort (SD-kort) 3 Ta ut SD-kortet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Trykk på SD-kortet for å løsne det fra datamaskinen. 3. Skyv SD-kortet ut av datamaskinen. Sette inn SD-kortet 1. Skyv SD-kortet inn i sporet til det klikker på plass. 2. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Batteri 4 Ta ut batteriet 1. 2. Følg fremgangsmåten i Før du arbeider på datamaskinen. Bruk skyvelåsene for å løsne batteriet. 3. Skyv ut batteriet, og ta det ut av datamaskinen. Sette inn batteriet 1. 2. Skyv batteriet inn i sporet til det klikker på plass. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
SIM-kort 5 Ta ut SIM-kortet 1. 2. 3. Følg fremgangsmåten i Før du arbeider på datamaskinen. Ta ut batteriet. Trykk på SIM-kortet for å løsne det fra datamaskinen. 4. Skyv SIM-kortet ut av datamaskinen.
Sette inn SIM-kortet 1. 2. 3. 20 Skyv SIM-kortet på plass. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Harddisk 6 Ta ut harddisken 1. 2. 3. Følg fremgangsmåten i Før du arbeider på datamaskinen. Ta ut batteriet. Skru ut skruene som holder harddisken til datamaskinen. 4. Skyv og ta harddisken ut av datamaskinen. 5. Skru ut skruen som holder harddiskholderen til harddisken.
6. Trekk og ta harddiskholderen ut av harddisken. Installere harddisken 1. 2. 3. 4. 5. Fest harddiskholderen til harddisken. Stram til skruene for å feste harddiskholderen til harddisken. Skyv harddisken inn i datamaskinen. Skru inn igjen, og stram til skruene som holder harddisken til datamaskinen. Sett inn batteriet. 6. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Optisk stasjon 7 Ta ut den optiske stasjonen 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Trykk og løsne låsen på den optiske stasjonen. 3. Skyv den optiske stasjonen ut av datamaskinen. 4. Skyv luken på den optiske stasjonen fra én side for å løsne den. 5. Skyv den andre siden av luken på den optiske stasjonen for å løsne den helt fra den optiske stasjonen.
6. Skru ut skruen som holder stasjonslåsen til den optiske stasjonen. 7. Ta stasjonslåsen av den optiske stasjonen. 8. Skru ut skruene som holder stasjonslåsbraketten til den optiske stasjonen.
9. Ta stasjonslåsbraketten av den optiske stasjonen. Sette inn den optiske stasjonen 1. Sett låsebraketten til stasjonen inn i den optiske stasjonen. 2. Stram til skruene for å feste låsebraketten til stasjonen til den optiske stasjonen. 3. Sett stasjonslåsen inn i den optiske stasjonen. 4. Stram til skruen for å feste stasjonslåsen til den optiske stasjonen. 5. Skyv luken på den optiske stasjonen til den sitter helt inn i den optiske stasjonen. 6.
Hoveddeksel 8 Ta av bunndekslet 1. 2. 3. 4. Følg fremgangsmåten i Før du arbeider på datamaskinen. Ta ut batteriet. Ta ut SD-kortet. Skru ut skruene som holder bunndekslet til datamaskinen. 5. Løft bunndekslet opp og bort fra datamaskinen.
Sette på bunndekslet 1. Plasser bunndekslet for å flukte skruhullene riktig med datamaskinen. 2. 3. 4. Skru inn igjen, og stram til skruene for å feste bunndekslet til datamaskinen. Sett inn SD-kortet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Minnekort 9 Ta ut minnet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta av bunndekslet. 5. Vri utløsertappene bort fra minnemodulen til de spretter opp. 6. Ta minnemodulen ut av datamaskinen.
Sette inn minnet 1. Sett minnemodulen inn i minnesporet. 2. 3. 4. 5. 6. Trykk på klipsene for å feste minnemodulen til hovedkortet. Sett på bunndekslet. Sett inn SD-kortet. Sett inn batteriet Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Klokkebatteri 10 Ta ut klokkebatteriet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta av bunndekslet. 5. Koble klokkebatterikabelen fra hovedkortet. 6. Løsne og ta klokkebatteriet ut av datamaskinen.
Sette inn klokkebatteriet 1. Plasser klokkebatteriet på plass. 2. 3. 4. 5. 6. Koble klokkebatterikabelen til hovedkortet. Sett på bunndekslet. Sett inn SD-kortet. Sett inn batteriet Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Kort for trådløst lokalnettverk (WLAN) 11 Ta ut kortet for trådløst lokalnettverk (WLAN) 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta av bunndekslet. 5. Koble antennekablene fra WLAN-kortet. 6. Skru ut skruen som holder WLAN-kortet til hovedkortet. 7. Ta WLAN-kortet ut av sporet på hovedkortet.
Sette inn kortet for trådløst lokalnettverk (WLAN) 1. 2. 3. 4. 5. 6. Sett WLAN-kortet inn i koblingen ved en 45–graders vinkel. Skru inn igjen, og stram til skruen som holder WLAN-kortet til datmaskinen. Koble til antennekablene i samsvar med fargekodingen på WLAN-kortet. Sett på bunndekslet. Sett inn SD-kortet. Sett inn batteriet. 7. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Kort for trådløst fjernnettverk (WWAN) 12 Ta ut kortet for trådløst fjernnettverk (WWAN) 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta av bunndekslet. 5. Koble antennekablene fra WWAN-kortet. 6. Skru ut skruen som holder WWAN-kortet til hovedkortet. 7. Ta WWAN-kortet ut av datamaskinen.
Sette inn kortet for trådløst fjernnettverk (WWAN) 1. 2. 3. 4. 5. 6. Sett inn WWAN-kortet i koblingen ved en 45–graders vinkel. Sett tilbake og stram til skruen som holder WWAN-kortet til datamaskinen. Koble til antennekablene i samsvar med fargekodingen på WLAN-kortet. Sett på bunndekslet. Sett inn SD-kortet. Sett inn batteret. 7. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Tastaturramme 13 Ta av tastaturrammen 1. 2. Følg fremgangsmåten i Før du arbeider på datamaskinen. Bruk et plastverktøy for å vri under tastaturrammen for å løsne den datamaskinen. 3. Løft tastaturrammen for å løsne tastene og fjerne den fra datamaskinen.
Sette på tastaturrammen 1. 2. 38 Juster tastaturrammen i forhold til tastaturet, og la den klikke på plass. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Tastatur 14 Ta av tastaturet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta av tastaturrammen. 4. Skru ut skruene som holder tastaturet til datamaskinen. 5. Skru ut skruene som holder tastaturet til håndstøtten. 6. Snu tastaturet, og legg det mot skjermen.
7. Løft klipsen for å løsne tastaturkabelen, koble den fra datamaskinen. 8. Ta av tastaturet fra datamaskinen. 9. Fjern teipen som holder tastaturkabelen til tastaturet.
10. Koble fra tastaturkabelen, og fjern den fra tastaturet. Sette på tastaturet 1. Koble tastaturkabelen, og fest den til tastaturet med teip. 2. Koble tastaturkabelen til koblingen på hovedkortet. 3. Snu tastaturet, og legg det på håndstøtten. 4. Skru på igjen, og stram til skruene for å feste tastaturet til håndstøtten. 5. Skru på igjen, og stram til skruene for å feste tastaturet til datamaskinen. 6. Sett inn batteriet. 7. Sett på tastaturrammen 8.
Håndleddstøtte 15 Ta av håndstøtten 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Skru ut skruene som holder håndstøtten til datamaskinen. 11. Snu datamaskinen, og koble fra følgende kabler fra hovedkortet.
12. Skru ut skruene for å løsne håndstøtten fra hovedkortet. 13. Løft håndstøtten langs kantene for å låse opp tastene, og ta den ut av håndstøtten.
Sette på håndstøtten 1. Tilpass håndstøtten til datamaskinen, og lås den på plass. 2. 3. Sett inn igjen, og stram skruene for å feste håndstøtten til hovedkortet. Koble følgende kabler til hovedkortet: 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. • LED-kort • styreplate • Bluetooth • kontaktfri Smart Card-leser • Express Card-kort • fingeravtrykksleser Skru inn igjen, og stram til skruene for å feste håndstøtten til datamaskinen. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken.
Bluetooth-kort 16 Ta ut Bluetooth-kortet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Ta av håndstøtten. 11. Skru ut skruene som holder Bluetooth-kortet til håndstøtten. 12. Ta Bluetooth-kortet ut av håndstøtten.
13. Løsne og fjern Bluetooth-kabelen fra Bluetooth-kortet. Sette inn Bluetooth-kortet 1. Koble Bluetooth-kabelen til Bluetooth-kortet. 2. Plasser Bluetooth-kortet på håndstøtten. 3. Skru inn igjen, og stram til skruen for å feste Bluetooth-kortet til håndstøtten. 4. Sett på håndstøtten. 5. Sett på tastaturet. 6. Sett på tastaturrammen. 7. Sett på harddisken. 8. Sett inn ExpressCard-kortet. 9. Sett på bunndekslet. 10. Sett på den optiske stasjonen. 11. Sett inn SD-kortet. 12.
LED-kort 17 Removing The LED Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Release the LED board cable from the routing channel. 12. Remove the screw that secures the LED board to the palm rest assembly.
13. Remove the LED board from the palm rest assembly.
Sette inn LED-kortet 1. Plasser LED-kortet på håndstøtten. 2. 3. 4. 5. 6. 7. Skru inn igjen, og stram til skruen som holder LED-kortet til håndstøtten. Før LED-kortkabelen frem til det opprinnelige stedet. Sett på håndstøtten. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken. 8. 9. 10. 11. 12. 13. Sett inn ExpressCard-kortet. Sett på bunndekslet. Sett på den optiske stasjonen. Sett inn SD-kortet. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Smartkortleser 18 Ta ut Smart Card-leseren 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Ta av håndstøtten. 11. Koble Smart Card-leserkabelen fra hovedkortet. 12. Ta ut skruene som holder Smart Card-leseren til datamaskinen.
13. Løft og ta Smart Card-leseren ut av datamaskinen.
Sette inn Smart Card-leseren 1. Plasser Smart Card-leseren på det opprinnelige stedet i datamaskinen. 2. Sett inn igjen og stram til skruene for å feste Smart Card-leseren til datamaskinen. Koble Smart Card-leserkabelen til hovedkortet. Skru inn igjen, og stram til skruene for å feste håndstøtten til datamaskinen. Sett på håndstøtten. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken. Sett inn ExpressCard-kortet. Sett på bunndekslet. Sett på den optiske stasjonen. Sett inn SD-kortet.
Mediekort 19 Ta ut mediekortet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Ta av håndstøtten. 11. Koble mediekortkabelen fra hovedkortet. 12. Skru ut skruene som holder mediekortet til datamaskinen.
13. Ta ut mediekortet fra datamaskinen.
Sette inn mediekortet 1. Plasser mediekortet der det befant seg opprinnelig på datamaskinen. 2. Skru inn igjen, og stram til skruene som holder mediekortet til datamaskinen. Koble mediekortkabelen til hovedkortet. Sett på håndstøtten. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken. Sett inn ExpressCard-kortet. Sett på bunndekslet. Sett på den optiske stasjonen. Sett inn SD-kortet. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. 3. 4. 5. 6. 7. 8. 9.
Skjermhengsler 20 Ta av skjermhengseldekslene 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Ta av håndstøtten. 11. Skru ut skruene som holder skjermhengseldekslene til datamaskinen. 12. Ta skjermhengseldekslene av datamaskinen.
Sette på skjermhengseldekslene 1. 2. 3. Plasser skjermhengslene på de aktuelle stedene. Skru inn igjen, og stram til skruene for å feste skjermhengseldekslene til datamaskinen. Sett på håndstøtten. 4. 5. 6. 7. 8. 9. 10. 11. 12. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken. Sett inn ExpressCard-kortet. Sett på bunndekslet. Sett på den optiske stasjonen. Sett inn SD-kortet. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Skjermenhet 21 Ta av skjermenheten 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta av bunndekslet. 6. Ta ut ExpressCard-kortet. 7. Ta ut harddisken. 8. Ta av tastaturrammen. 9. Ta av tastaturet. 10. Ta av håndstøtten. 11. Ta av skjermhengseldekslene. 12. Løsne antennekablene fra datamaskinen. 13. Skru ut skruene som holder skjermenheten til datamaskinen.
14. Trekk antennekablene ut av føringskanalene? 15. Skru ut skruene som holder skjermkabelbraketten til hovedkortet.
16. Ta skjermkabelbraketten av datamaskinen. 17. Skyv skjermkabelen for å koble den fra hovedkortet. 18. Skru ut skruen som holder skjermenheten til datamaskinen.
19. Ta skjermenheten ut av datamaskinbasen.
Sette på skjermenheten 1. Sett skjermenheten tilbake i den opprinnelige stillingen på datamaskinen. 2. Skru inn igjen, og stram til skruen som holder skjermenheten til datamaskinen. 3. Sett på igjen, og koble skjermkabelen til hovedkortet. 4. Sett skjermkabelbraketten tilbake på det opprinnelige stedet. 5. Skru inn igjen, og stram til skruene som holder skjermkabelbraketten til hovedkortet. 6. Før antennekablene gjennom hovedkortet: 7.
Hovedkort 22 Ta ut hovedkortet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta ut SIM-kortet. 6. Ta av bunndekslet. 7. Ta ut ExpressCard-kortet. 8. Ta ut harddisken. 9. Ta av tastaturrammen. 10. Ta av tastaturet. 11. Ta ut kortet for trådløst lokalnettverk (WLAN). 12. Ta ut kortet for trådløst fjernnettverk (WWAN). 13. Ta ut klokkebatteriet. 14. Ta ut mediekortet. 15. Ta av håndstøtten. 16.
19. Skru ut skruene som holder hovedkortet til datamaskinen. 20. Løft hovedkortet for å finne strømkabelen. 21. Koble strømkabelen fra hovedkortet.
22. Løft og ta ut hovedkortet fra datamaskinen. MERK: Trinn 23 og 24 gjelder datamaskiner som leveres i USA. 23. Snu systemet, og ta ut skruen som holder TAA-kortet. 24. Ta TAA-kortet ut av systemet.
Sette inn hovedkortet 1. Plasser TAA-kortet på det opprinnelige stedet. MERK: Trinn 1 og 2 gjelder datamaskiner som leveres i USA. 2. 3. 4. 5. 6. 7. Sett inn igjen og, stram til skruen for å feste TAA-kortet til datamaskinen. Plasser hovedkortet tilbake i den opprinnelige stillingen på datamaskinen. Koble til strømkabelen. Sett inn igjen og, stram til skruene for å feste TAA-kortet til datamaskinen. Plasser og koble Smart Card og høyttalerkablene til hovedkortet. Sett på skjermenheten. 8. 9. 10. 11.
Varmeavleder 23 Ta ut varmeavlederenhet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta ut SIM-kortet. 6. Ta av bunndekslet. 7. Ta ut ExpressCard-kortet. 8. Ta ut harddisken. 9. Ta av tastaturrammen. 10. Ta av tastaturet. 11. Ta ut kortet for trådløst lokalnettverk (WLAN). 12. Ta ut kortet for trådløst fjernnettverk (WWAN). 13. Ta ut klokkebatteriet. 14. Ta ut mediekortet. 15. Ta av håndstøtten. 16.
20. Løsne skruene som holder varmeavlederenheten til hovedkortet. 21. Fjern varmeavlederenhet fra hovedkortet.
Sette inn varmeavlederenheten 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Plasser varmeavlederenheten tilbake i den opprinnelige stillingen på hovedkortet. Stram skruene jevnt for å feste varmeavlederenheten til hovedkortet. Koble varmeavlederkabelen til hovedkortet. Sett på varmeavlederenheten. Sett på skjermenheten. Sett på skjermhengseldekslene. Sett på håndstøtten. Sett på tastaturet. Sett på tastaturrammen. Sett på harddisken. Sett inn ExpressCard-kortet. Sett på bunndekslet.
Inn- og utgangspanel 24 Ta ut inn- og utgangspanelet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta ut SIM-kortet. 6. Ta av bunndekslet. 7. Ta ut ExpressCard-kortet. 8. Ta ut harddisken. 9. Ta av tastaturrammen. 10. Ta av tastaturet. 11. Ta ut kortet for trådløst lokalnettverk (WLAN). 12. Ta ut kortet for trådløst fjernnettverk (WWAN). 13. Ta ut klokkebatteriet. 14. Ta ut mediekortet. 15.
19. Ta I/U-panelet av datamaskinen.
Sette på inn- og utgangspanelet 1. Sett I/U-panelet på plass igjen i datamaskinen. 2. 3. 4. 5. 6. 7. Stram til skruene som holder I/U-panelet til datamaskinen. Sett på skjermenheten. Sett på skjermhengseldekslene. Sett på håndstøtten. Sett på tastaturet. Sett på tastaturrammen. 8. 9. 10. 11. 12. 13. 14. Sett på harddisken. Sett inn ExpressCard-kortet. Sett på bunndekslet. Sett på den optiske stasjonen. Sett inn SD-kortet. Sett inn batteriet.
Høyttaler 25 Ta av høyttalerne 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta av bunndekslet. 4. Ta ut SD-kortet. 5. Ta ut den optiske stasjonen. 6. Ta ut SIM-kortet. 7. Ta ut ExpressCard-kortet. 8. Ta ut harddisken. 9. Ta av tastaturrammen. 10. Ta av tastaturet. 11. Ta ut kortet for trådløst lokalnettverk (WLAN). 12. Ta ut kortet for trådløst fjernnettverk (WWAN). 13. Ta ut klokkebatteriet. 14. Ta ut mediekortet. 15. Ta av håndstøtten. 16.
20. Skru ut skruene som holder høyttalerne til datamaskinen. 21. Ta høyttalerne av datamaskinen.
Sette på høyttalerne 1. Sett høyttalerne tilbake på det opprinnelige stedet på datamaskinen. 2. Stram til skruene for å feste høyttalerne til datamaskinen. 3. Legg på plass, og koble til høyttalerkabelen. 4. Sett inn hovedkoret. 5. Sett på skjermenheten. 6. Sett på skjermhengseldekslene. 7. Sett på håndstøtten. 8. Sett inn klokkebatteriet. 9. Sett inn kortet for trådløst lokalnettverk (WLAN). 10. Sett inn kortet for trådløst fjernnettverk (WWAN). 11. Sett på tastaturet. 12.
Likestrøm inn-port 26 Ta av inngangsporten til strøm 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta ut SD-kortet. 4. Ta ut den optiske stasjonen. 5. Ta ut SIM-kortet. 6. Ta av bunndekslet. 7. Ta ut ExpressCard-kortet. 8. Ta ut harddisken. 9. Ta av tastaturrammen. 10. Ta av tastaturet. 11. Ta ut kortet for trådløst lokalnettverk (WLAN). 12. Ta ut kortet for trådløst fjernnettverk (WWAN). 13. Ta ut klokkebatteriet. 14. Ta ut mediekortet. 15.
20. Ta strømbraketten av systemet. 21. Ta strømporten av systemet.
Sette på inngangsporten til strøm 1. Sett inngangsporten til strøm tilbake på det opprinnelige stedet på datamaskinen. 2. Sett strømbraketten tilbake på det opprinnelige stedet på datamaskinen. 3. Stram til skruen for å feste strømbraketten til datamaskinen. 4. Sett inn hovedkortet. 5. Sett på skjermenheten. 6. Sett på skjermhengseldekslene. 7. Sett på håndstøtten. 8. Sett inn mediekortet. 9. Sett inn kortet for trådløst lokalnettverk (WLAN) 10.
Skjermramme 27 Ta av skjermrammen 1. 2. 3. Følg fremgangsmåten i Før du arbeider på datamaskinen. Ta ut batteriet. Begynn i bunnen, og vri rammen fra innsiden av skjermenheten. 4. Ta skjermrammen av skjermenheten.
Sette på skjermrammen 1. Plasser skjermrammen på skjermenheten. 2. 3. 4. 5. Trykk langs kantene på toppen og bunnen av skjermrammen. Trykk langs kantene til venstre og høyre på skjermrammen. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Skjermpanel 28 Ta av skjermpanelet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta av skjermrammen. 4. Ta ut skruene som holder skjermpanelet til skjermenheten. 5. Snu skjermpanelet. 6. Koble LVDS-kabelen fra skjermpanelet.
7. Ta av skjermpanelet fra skjermenheten. Sette på skjermpanelet 1. Sett skjermpanelet tilbake på det opprinnelige stedet på skjermenheten. 2. Koble LVDS-kabelen til skjermpanelet. 3. Stram til skruene for å feste skjermpanelet til skjermenheten. 4. Sett på skjermrammen. 5. Sett inn batteriet. 6. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Kamera 29 Ta ut kameraet 1. Følg fremgangsmåten i Før du arbeider på datamaskinen. 2. Ta ut batteriet. 3. Ta av skjermrammen. 4. Ta av skjermpanelet. 5. Koble kabelen fra kameramodulen. 6. Skru ut skruen som holder kameraet og mikrofonen til skjermenheten.
7. Ta kameraet ut av skjermenheten. Sette inn kameraet 1. 2. 3. 4. 5. 6. 7. 94 Plasser kameramodulen på det opprinnelige stedet i skjermenheten. Stram til skruen for å feste kameraet til skjermenheten. Koble kamerakabelen til kameraet. Sett på visningsskjermen. Sett på skjermrammen. Sett inn batteriet. Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
30 Spesifikasjoner Tekniske spesifikasjoner MERK: Tilbudet kan variere fra sted til sted. Følgende spesifikasjoner er bare dem som loven krever at skal følge med datamaskinen. Hvis du vil ha mer informasjon om datamaskinens konfigurasjon, klikker du på Start → Hjelp og støtte, og velger alternativet for å vise informasjon om datamaskinen.
Lyd Type firekanals høydefinisjonslyd Kontroller IDT 92HD90 Stereokonvertering 24-biters (analog-til-digital og digital-til-analog) Grensesnitt: Internt High Definition-lyd Eksternt mikrofoninngang / kontakt for stereohodetelefoner / eksterne høyttalerkobling Høyttalere To Intern høyttalerforsterker 0,5 W (typisk) per kanal Volumkontroller funksjonstaster på tastaturet og programmeny Video Type integrert på hovedkortet Kontroller Intel HD Graphics Kommunikasjon Nettverksadapter 10/100/1
Kontaktløst smartkort Støttede Smart Cards / teknologier ISO14443A — 106 kbps, 212 kbps, 424 kbps og 848 kbps ISO14443B — 106 kbps, 212 kbps, 424 kbps og 848 kbps ISO15693 HID iClass FIPS201 NXP Desfire Skjerm Type WLED-skjerm (white Light Emitting Diode) Størrelse 13,3-tommers HD (high definition) Aktivt område (X/Y) 293,42 mm x 164,97 mm Dimensjoner: Høyde 189,00 mm (7,44") Bredde 314,00 mm (12,36") Diagonal 337,82 mm (13,30") Maksimal oppløsning 1366 x 768 piksler med 263 000 farger Maksi
Styreplate X-akse 80,00 mm Y-akse 40,70 mm Batteri Type • • • 3-cellers (30 Watt-timer) litiumionbatteri med ExpressCharge 6-cellers (60 Watt-timer) litiumionbatteri med ExpressCharge 6-cellers (58 Watt-timer) litiumionbatteri Dimensjoner: 3-cellers Dybde 29,97 mm (1,18") Høyde 19,80 mm (0,78") Bredde 208,00 mm (8,19") 6-cellers Dybde 54,10 mm (2,13") Høyde 20,85 mm (0,82") Bredde 214,00 mm (8,43") Vekt: 3-cellers 177,00 g (0,39 lb) 6-cellers 349,00 g (0,77 lb) Ladetid med datamaskine
Batteri Klokkebatteri 3 V CR2032-litiumbatteri Strømadapter Type 65 W og 90 W Inngangsspenning 100 VAC til 240 VAC Inngangsstrøm (maks.
Omgivelser Ved bruk –15,24 m til 3048 m (–50 fot til 10 000 fot) Ikke i bruk –15,24 m til 10 668 m (–50 fot til 35 000 fot) Luftforurensningsnivå 100 G1 som definert i ISA-S71.
Systemoppsett 31 Oversikt I System Setup-programmet kan du: • • • endre systemkonfigurasjonen etter at du har lagt til, endret eller fjernet maskinvare på datamaskinen velge eller endre brukertilgjengelige alternativer, for eksempel brukerpassordet se hvor mye minne som er tilgjengelig, eller angi hvilken type harddisk som er installert Før du bruker System Setup (Systemoppsett) anbefaler vi at du skriver informasjon i skjermen System Setup (Systemoppsett) som referansemateriale i fremtiden.
Generelt Valg Beskrivelse System Information (systeminformasjon) Denne delen inneholder en oversikt over de viktigste maskinvarefunksjonene på datamaskinen. • • • • System Information (systeminformasjon) Memory Information (minneinformasjon) Processor Information (prosessorinformasjon) Device Information (enhetsinformasjon) Battery Information (batteriinformasjon) Viser batteristatusen og hvilken type strømadapter som er koblet til datamaskinen.
System Configuration (systemkonfigurasjon) Valg Beskrivelse MERK: System Configuration (Systemkonfigurasjon) inneholder valg og innstillinger i forbindelse med integrerte systemenheter. Hva som står oppført i denne delen vil være avhengig av datamaskinen og enheter som er installert. Integrated NIC (integrert nettverkskort) Her kan du konfigurere den integrerte nettverkskontrolleren.
Valg Beskrivelse SATA Operation (SATA-funksjon) Her kan du konfigurere den interne SATAharddiskkontrolleren. Alternativene er: • • • • Disabled (Deaktivert) ATA AHCI RAID On (På) Standard innstilling: RAID On (På) MERK: SATA er konfigurert til å støtte RAID-modus. USB Controller (USB-kontroller) Her kan du styre USB-kontrolleren.
Valg Beskrivelse Du kan også aktivere eller deaktivere mediekort og 1394 sammen. Standardinnstilling: Alle enheter er aktivert. Keyboard illumination (tastaturlys) Her kan du konfigurere funksjonen for tastaturlys.
Valg Beskrivelse MERK: Passordendringer trer i kraft umiddelbart. MERK: Hvis du sletter administratorpassordet, slettes system- og harddiskpassordet automatisk. MERK: Passordendringer trer i kraft umiddelbart. Standardinnstilling: Ikke angitt System Password (systempassord) Her kan du angi, endre eller slette systempassordet. MERK: Passordendringer trer i kraft umiddelbart.
Valg Beskrivelse Strong Password (sterkt passord) Her kan du få hjelp til alltid å angi sterke passord. Standardinnstilling: Enable Strong Password (Aktiver sterkt passord) er ikke valgt. OROM Keyboard Access (OROM tastaturtilgang) Her kan du angi et alternativ for å få tilgang til alternativ ROM-konfigurasjon ved hjelp av hurtigtaster under oppstart.
Valg Beskrivelse Hvis alternativet er deaktivert, er oppsettalternativene låst av administratorpassordet. Standard innstilling: Allow Wireless Switch Changes (Tillate at trådløs bryter endres) er ikke valgt. Password Configuration (passordkonfigurering) Her kan du fastsette minimum og maksimum lengde på administrator- og systempassord. Utestengning fra oppsett ved angitt administratorpassord Gjør at du kan hindre brukere i å komme inn i oppsettet når det er angitt et administratorpassord.
Valg Beskrivelse Limit CPUID (Begrens CPU-ID) Her kan du begrense maksimumverdien som prosessorens standard CP-UIDfunksjon vil støtte. Standard innstilling: Enable Intel CPUID (Aktiver Intel CPUID) er valgt. Intel TurboBoost Her kan du aktivere eller deaktivere prosessormodusen Intel TurboBoost. Standard innstilling: Enable Intel TurboBoost (Aktiver Intel TurboBoost) er valgt. HyperThread Control (Hypertrådstyring) Her kan du aktivere eller deaktivere hypertrådkjøring i prosessoren.
Valg Beskrivelse MERK: Denne funksjonen fungerer bare hvis systemet er koblet til strøm. Hvis strømadapteren fjernes i ventemodus, vil systemoppsettet stenge strømmen fra alle USB-porter for å spare på batteriet. Wireless Radio Control (trådløs radiostyring) Her kan du aktivere eller deaktivere funksjonen som automatisk veksler mellom kablede eller trådløse nettverk uten å være avhengig av den fysiske tilkoblingen.
Valg Beskrivelse Mouse/Touchpad (mus/berøringsplate) Her kan du definere hvordan systemet skal håndtere inndata for mus og berøringsplate. Alternativene er: • • • Serial Mouse (seriell mus) PS2 Mouse (PS2-mus) Berøringsplate/PS-2-mus Standard innstilling: Touchpad/PS-2 On (Berøringsplate / PS-2 På) Numlock Enable (Aktiver NumLock) Her kan du aktivere alternativet NumLock når du starter datamaskinen. Standard innstilling: Enable Numlock (Aktiver Numlock) er valgt.
Virtualization Support (virtualiseringsstøtte) Valg Beskrivelse Virtualization (virtualisering) Her kan du aktivere eller deaktivere funksjonen Intel Virtualization Technology. Standard innstilling: Enable Intel Virtualization Technology (Aktiver Intel Virtualization Technology) er valgt. VT for Direct I/O (VT for direkte I/O) Her kan du aktivere eller deaktivere Virtualization Technology for Direkte I/O. Standard innstilling: Enable VT I/O Support (Aktivert VT I/O-støtte) er valgt.
System Logs (systemlogger) Valg Beskrivelse BIOS Events (BIOS-hendelser) Her kan du vise og fjerne (BIOS) POSThendelsene i systemoppsettet. DellDiag Events (DellDiag-hendelser) Her kan du vise og fjerne DellDiaghendelsene. Thermal Events (varmehendelser) Her kan du vise og fjerne varmehendelsene. Power Events (strømhendelser) Her kan du vise og fjerne strømhendelsene. BIOS Progress Events (fremdriftshendelser for BIOS) Her kan du vise og fjerne fremdriftshendelsene for BIOS.
32 Diagnostikk Enhetsstatuslamper Slås på når du slår på datamaskinen og blinker når datamaskinen er i en strømstyringsmodus. Slås på når datamaskinen leser eller skriver data. Slås på og lyser konstant eller blinker for å angi batteriets ladestatus. Slås på når trådløst nettverk er aktivert.
Utseende Fast Blink er Beskrivelse Fast Minnet er funnet,men har feil. Neste trinn 1. Sett tilbake minnet. 2. Ta ut én modul og test den dersom to moduler er satt inn. Forsøk den andre modulen i samme spor og test. Test det andre sporet med begge modulene. 3. Sett på plass minnemodulen. 4. Sett inn hovedkortet igjen. Blinke Blink r er Blink Feil på er hovedkortet Sett inn hovedkortet igjen. Blinke Blink r er Fast Feil på videokortet Sett inn hovedkortet igjen.
Kontakte Dell 33 kontakte Dell MERK: Hvis du ikke har en aktiv Internett-tilkobling, kan du finne kontaktinformasjon på fakturaen, følgeseddelen, regningen eller i Dells produktkatalog. Dell tilbyr flere nettbaserte og telefonbaserte støtte- og servicealternativer. Tilgjengeligheten varierer etter land og produkt. Det kan hende at enkelte tjenester ikke er tilgjengelige i ditt område. For å kontakte Dell for spørsmål om salg, teknisk støtte eller kundeservice: 1. 2. 3. 4. Gå til support.dell.com.