Administrator Guide

NOTE: The CLI output may be incorrectly displayed as 0 (zero) for the Rx/Tx power values. To obtain the correct
power information, perform a simple network management protocol (SNMP) query.
The following example shows the configuration and status information for one interface.
DellEMC#show interfaces gigabitethernet 1/1
GigabitEthernet 1/1 is up, line protocol is up
Hardware is Force10Eth, address is 00:01:e8:05:f3:6a
Current address is 00:01:e8:05:f3:6a
Pluggable media present, XFP type is 10GBASE-LR.
Medium is MultiRate, Wavelength is 1310nm
XFP receive power reading is -3.7685
Interface index is 67436603
Internet address is 65.113.24.238/28
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed 10000 Mbit, Mode full duplex, Master
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 00:09:54
Queueing strategy: fifo
Input Statistics:
0 packets, 0 bytes
0 Vlans
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output Statistics:
3 packets, 192 bytes, 0 underruns
3 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 3 Broadcasts, 0 Unicasts
0 Vlans, 0 throttles, 0 discarded, 0 collisions
Rate info (interval 299 seconds):
Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 00:00:31
DellEMC#
To view which interfaces are enabled for Layer 3 data transmission, use the show ip interfaces brief command in EXEC
Privilege mode. In the following example, TenGigabitEthernet interface 1/6 is in Layer 3 mode because an IP address has been assigned to
it and the interface’s status is operationally up.
DellEMC#show ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet 1/1 unassigned NO Manual administratively down down
GigabitEthernet 1/2 unassigned NO Manual administratively down down
GigabitEthernet 1/3 unassigned YES Manual up up
GigabitEthernet 1/4 unassigned YES Manual up up
GigabitEthernet 1/5 unassigned YES Manual up up
GigabitEthernet 1/6 10.10.10.1 YES Manual up up
GigabitEthernet 1/7 unassigned NO Manual administratively down down
GigabitEthernet 1/8 unassigned NO Manual administratively down down
GigabitEthernet 1/9 unassigned NO Manual administratively down down
To view only configured interfaces, use the show interfaces configured command in the EXEC Privilege mode.
To determine which physical interfaces are available, use the show running-config command in EXEC mode. This command displays
all physical interfaces available on the system.
DellEMC#show running
Current Configuration ...
!
interface GigabitEthernet 2/6
no ip address
shutdown
!
interface GigabitEthernet 2/7
no ip address
shutdown
!
Interfaces
303