Setup Guide

If a pre–conguration script le downloads successfully, the following SYSLOGs display:
00:03:07: %STKUNIT0-M:CP %BMP-2-BMP_DOWNLOAD_START: The config
file download has started.
00:03:19: %STKUNIT0-M:CP %BMP-5-BMP_DWNLD_FILE_IS_SCRIPT_FILE:
The downloaded file is a script file.
00:03:19: %STKUNIT0-M:CP
%BMP-5-BMP_DWNLD_CONFIG_SCRIPT_SUCCESS: The config/script file
download is successful.
00:03:21: %STKUNIT0-M:CP %BMP-5-BMP_PRE_CONFIG_SCRIPT_BEGIN:
The Pre-Config Script has started to Execute.
After the pre–conguration script executes successfully, the startup conguration le loads.
00:04:30: %STKUNIT0-M:CP %BMP-5-BMP_PRE_CONFIG_SCRIPT_END:
Pre-Config script completed with return status 0.
00:03:03: %STKUNIT0-M:CP %IFMGR-5-ASTATE_DN: Changed interface
Admin state to down: Ma 0/0.
00:03:03: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface
state to down: Ma 0/0.
00:03:03: %STKUNIT0-M:CP %SYS-5-CONFIG_LOAD: Loading
configuration file.
00:03:04: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface
Admin state to up: Ma 0/0.
If a post–conguration script is present in the applied conguration le, it executes and the logs display:
00:04:22: %STKUNIT0-M:CP %BMP-5-BMP_POST_CONFIG_SCRIPT_BEGIN:
The Post-Config Script has started to Execute
..
00:05:15: %STKUNIT0-M:CP %BMP-5-BMP_POST_CONFIG_SCRIPT_END:
Post-Config script completed with return status 0.
If a post–conguration script is not present in the applied conguration le, the logs display:
00:03:03: %STKUNIT0-M:CP %SYS-5-CONFIG_LOAD: Loading
configuration file.
00:03:04: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed interface
Admin state to up: Ma 0/0.
00:03:04: %STKUNIT0-M:CP %BMP-5-BMP_POST_SCRIPT_NOT_PRESENT:
The Post-Config Script is not present.
DHCP Oer Vendor-Specic Option for BMP
To congure FIPS mode for your system, use the vendor-specic DHCP OFFER option (code 231) called fips-mode-enabled so that
BMP can decide to use the non-FIPS-approved algorithms for the image/cong-le download process.
This option accepts the boolean type value TRUE/FALSE to enable or disable FIPS mode. BMP uses this setting temporarily and only for
the image/cong-le download process. BMP never stores this in either the runing-cong or startup-cong. The DHCP OFFER controls
using non-FIPS-approved algorithms by the BMP-initiated le download process. If you have not congured this option, by default BMP
assumes you have disabled FIP mode.
• If the value is set to TRUE, BMP enables FIPS mode and uses the relevant FIPS-approved algorithms for the image/cong-le
download process.
• If the value is set to FALSE, BMP disables FIPS mode and uses the non-FIPS-approved algorithms for the image/cong-le download
process.
DHCP Oer Relay Option 82
Dell EMC Networking OS supports option 82 in DHCP oer. With option 82, the switch appends the interface details while sending the
DHCP discover packet. To support option 82, the congured circuit ID and remote IDs are lled in the DHCP discover packets. The
reload-type command has an option to enable or disable the DHCP oer option 82. By default, the option 82 is disabled. To enable the
option 82, you have to congure the remote ID using the reload-type sub-command relay remote-id "mac/hostname/
custom string
.
24
Bare Metal Provisioning