Dell OpenManage Deployment Toolkit Version 5.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 Introduction........................................................................................................... 8 What is new in this release....................................................................................................................8 Supported Systems................................................................................................................................9 Supported operating systems............................................................
-h or --help................................................................................................................................... 22 -i or --infile....................................................................................................................................23 --ix or --inxmlfile.......................................................................................................................... 23 -l or --logfile........................................................
--hddfailover............................................................................................................................... 124 --hpcmode.................................................................................................................................. 125 --htassist...................................................................................................................................... 125 --idecdrom................................................................
serialchannelinfo......................................................................................................................... 145 serialuseraccess...........................................................................................................................145 solaction.......................................................................................................................................147 solcfgparams..................................................................
Configuring Physical Disk Rebuild.............................................................................................. 195 Configuring Array Disk As RAID ................................................................................................. 196 Configuring Physical Disk State.................................................................................................. 196 Replacing Physical Disk Of A Virtual Disk........................................................................
Introduction 1 Dell OpenManage Deployment Toolkit (DTK) includes a set of utilities, sample scripts, and sample configuration files to deploy and configure your Dell system. You can use DTK to build script-based and RPM-based installation for deploying a large number of systems reliably, without changing their current deployment processes. You can use DTK in a Microsoft Windows Preinstallation Environment (Windows PE) or a Linux environment.
NOTE: Use both DTK and the Server Administrator from the same release version to get complete supported features of Server Administrator. Supported Systems For a complete list of supported Dell PowerEdge systems, see the Dell Systems Software Support Matrix in the required version of OpenManage Software at dell.com/openmanagemanuals Supported operating systems DTK utilities support Windows PE 5.1 (64-bit), Windows PE 4.0 (64-bit), and Windows PE 3.
Additionally, the utilities can be integrated with the sample files provided with the toolkit to fully configure one-to-many target systems in a scripted mass system deployment. System Configuration Utility The SYSCFG utility performs the following tasks: • Reports and sets BIOS configuration options. • Reports and sets BMC/RAC configuration options. • Reports and sets user-configurable states. • Reports system information, including PCI device detection.
If these values do not match the values found on the system, the file input operation fails. The following is the SYSCFG behavior during replication: • Options not available in SYSCFG are termed invalid options. If SYSCFG encounters an invalid option in the syscfg.ini file, the SYSCFG utility terminates. • Unsupported options are options available in SYSCFG but not applicable on certain systems. If SYSCFG encounters an unsupported option, SYSCFG logs this option and continues to the next option.
• The Integrated Dell Remote Access Controller 8 (iDRAC8) Command Line Interface Reference Guide provides information about the RACADM subcommands, supported interfaces, property database groups and object definitions for iDRAC8 and CMC. • The Integrated Dell Remote Access Controller 8 (iDRAC8) User's Guide provides information about configuring and using iDRAC8 for 13th generation rack, tower, and blade servers to remotely manage and monitor your system and its shared resources through a network.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Visit www.dell.com/support . 2. Select your support category. 3. If you are not a U.S customer, select your country code at the bottom of the page, or select All to see more choices. 4. Select the appropriate service or support link based on your need.
Command Syntax Overview 2 Syntax refers to the way a command and its parameters are entered. Dell OpenManage Deployment Toolkit (DTK) Command Line Interface (CLI) commands can be arranged in any order as long as they conform to the basic command line syntax. DTK Utilities General Usage The following table lists the general usage models of the DTK utilities: Table 1. DTK Utilities Utilities Usage SYSCFG syscfg --option1=[arg1] ... --optionX=[argX] or syscfg bmcoption1 --bmcsuboption1=[arg1]...
Command Line Syntax The following table lists the generic command line characters and arguments present in the command line options with a short description of these characters. Table 2. Command Line Options Element Description - Prefix single character options. NOTE: This delimiter is not applicable to Baseboard Management Controller (BMC) sub-options. -- Prefix multi-character options. utilname Indicates the generic designation for a DTK utility name.
• Unless specified otherwise, enter all commands, options, arguments, and command line switches in lowercase letters. Command Line Option Delimiters The following table lists some examples of valid and invalid DTK command lines. Table 3.
Delimiter Example Description A double quotation mark preceded by a backslash (\") is interpreted as a literal double quotation mark ("). syscfg -option="\"argument" considers "argument as the argument. syscfg --option="\ Backslashes are interpreted literally, unless they immediately \"argument" precede a double quotation mark. If an even number of backslashes are followed by a double quotation mark, then one backslash (\) is taken for every pair of backslashes (\\), and the double quotation mark (")
Log Files If the log file already exists, information is appended to the file. This allows multiple tools to use the same log file to record information. Use the -l option to record the output of a utility. The log duplicates all standard output and error information to the specified file. Each log file begins with a time stamp and utility name. For example, YYYY/MM/DD HH:MM:SS < utilname > -
DTK Seamless package 3 The DTK Seamless package is a single installer package that carries Linux DTK RPMs (RHEL, SLES) and its dependency. Seamless package — Downloading and Installing This section describes the downloading and installing of DTK seamless package. The seamless package auto recognizes the OS type and its respective dependency during the installation and installs SYSCFG, RAIDCFG, and RACADM tools on post Linux operating system.
Enter q to quit. Once the DTK tools installation is complete, success message is displayed on the screen. To uninstall the DTK tools, run the command /opt/dell/toolkit/bin/dtktools-uninstall.sh —d Non-interactive mode: In the non-interactive mode, all the available tools are installed by default. Any other option is ignored. Type the following command: ./DTKTOOLS__Linux64_.Bin [—f/--force] Once the DTK tools installation is complete, success message is displayed on the screen.
SYSCFG 4 This section documents the Deployment Toolkit (DTK) system configuration utility. It describes the command line parameters, configuration file format, and individual executables used to configure server BIOS and Baseboard Management Controller (BMC) settings, DTK state settings, and system information including PCI device detection. Features The SYSCFG utility: • Displays help and usage information. • Outputs configuration options to a file or screen.
No Option Valid Arguments NA Description The SYSCFG utility displays the usage information. --envar Valid Arguments Description Stores the environment variable data to a file when used with the – s option. This file can be called from other scripts to set the environment variable. The value of must not be specified if the DTKENVSCR environment variable is set to a valid filename.
Example: A:>syscfg -h lanchannelaccess lanchannelaccess: Reports LAN channel access information. Sub-options: pefalerting: Enable or disable PEF (Platform Event Filter)alerting. Arguments: enable | disable ipmioverlan: Enable or disable IPMI over LAN access. Arguments: disable | alwaysavail channelprivlmt: Sets the maximum privilege level that can be accepted on the LAN channel.
NOTE: It is applicable only on 12G and later systems. Example: A:>syscfg --ix filename.xml NOTE: You can modify or use the BIOS configuration captured in xml format from a PowerEdge server for large scale deployment configurations using RACADM or WS-MAN. For more information on using RACADM and WS-MAN refer Integrated Dell Remote Access Controller 8 (iDRAC8) RACADM Command Line Interface Reference Guide and Dell Lifecycle Controller-Remote Services Quick Start Guide respectively available at dell.
NOTE: It is applicable only on 12G and later sytems. Example: A:>syscfg --ox filename.ini --ovrwrt* Valid Arguments NA Description Used with the -o option to cause the output file to be overwritten if a file of the same name already exists. This option cannot be replicated. Example: A:>syscfg -o=filename.ini --ovrwrt The file filename has been overwritten. --px or --pendingxmlfile Valid Arguments Description Prints all the pending BIOS options to a specified xml file.
Example: A:>syscfg --version syscfg Version 4.4 P01(Windows - Jan 29 2014,16:48:48) Copyright (c) 2002-2014 Dell Inc. SYSCFG For BIOS Configuration SYSCFG uses BIOS interfaces to manipulate boot order and BIOS settings. It configures all options available on the BIOS setup screen, including boot order, embedded device configuration, and asset tag management. Consider the following while using the SYSCF options: • On systems prior to 12G, options and arguments are case-sensitive.
Table 6. BIOS options with equivalent RACADM options Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems BIOS Option Settings --BootSeq --bootseq BIOS.BiosBootSettings.BootSeq --HddSeq --devseq BIOS.BiosBootSettings.HddSeq --BootMode --bootmode BIOS.BiosBootSettings.BootMode --BootSeqRetry --bootseqretry BIOS.BiosBootSettings.BootSeqRetry --HddFailover --hddfailover BIOS.BiosBootSettings.HddFailover N/A BIOS.BiosBootSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems -InternalSdCardRedu ndancy -BIOS.IntegratedDevices.InternalSdCar embsdcardredunda dRedundancy ncy --InternalUsb --internalusb BIOS.IntegratedDevices.InternalUsb --InternalUsb1 --internalusbport1 BIOS.IntegratedDevices.InternalUsb1 --InternalUsb2 --internalusbport2 BIOS.IntegratedDevices.InternalUsb2 -OsWatchdogTimer -oswatchdogtimer BIOS.IntegratedDevices.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems --MemOpMode -BIOS.MemSettings.MemOpMode memoperatingmod e --MemOpVoltage --dimmvoltage BIOS.MemSettings.MemOpVoltage --MemTest --memtest BIOS.MemSettings.MemTest --NodeInterleave --nodeinterleave BIOS.MemSettings.NodeInterleave --RedundantMem --redmem BIOS.MemSettings.RedundantMem --SerialDbgOut N/A BIOS.MemSettings.Serialdbgout --SysMemSize* --mem* BIOS.MemSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on 13G and later systems. -N/A InSystemCharacteriz ation BIOS.MiscSettings.InSystemCharacteri zation NOTE: The option is supported only on 13G and later systems. --ReportKbdErr --rptkeyerr BIOS.MiscSettings.ReportKbdErr --PxeDevnEnDis N/A BIOS.NetworkSettings.PxeDevnEnDis --PxeDevnInterface N/A BIOS.PxeDevice1Settings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is not supported on Dell PowerEdge 13G and later systems. Processor Settings ---nextboot OneTimeBootSeqDe v BIOS.OneTimeBoot.OneTimeBootSeq Dev -OneTimeHddSeqDe v BIOS.OneTimeBoot.OneTimeHddSeq Dev N/A -N/A OneTimeUefiBootSe qDev BIOS.OneTimeBoot.OneTimeUefiBoot SeqDev --DataReuse --datareuse BIOS.ProcSettings.DataReuse --DcuIpPrefetcher N/A BIOS.ProcSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems --Proc3L3Cache* N/A BIOS.ProcSettings.Proc3L3Cache --Proc3NumCores* N/A BIOS.ProcSettings.Proc3NumCores --Proc4Brand* N/A BIOS.ProcSettings.Proc4Brand --Proc4Id* N/A BIOS.ProcSettings.Proc4Id --Proc4L2Cache* N/A BIOS.ProcSettings.Proc4L2Cache --Proc4L3Cache* N/A BIOS.ProcSettings.Proc4L3Cache --Proc4NumCores* N/A BIOS.ProcSettings.Proc4NumCores --Proc64bit* N/A BIOS.ProcSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on Dell PowerEdge 13G and later systems. --ProcX2Apic N/A BIOS.ProcSettings.ProcX2Apic --EmbSata --embsataraid BIOS.SataSettings.EmbSata --eSataPort1 N/A BIOS.SataSettings.eSataPort1 -eSataPort1Capacity* N/A BIOS.SataSettings.eSataPort1Capacity -N/A eSataPort1DriveType * BIOS.SataSettings.eSataPort1DriveTyp e --eSataPort1Model* N/A BIOS.SataSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems -SataPortCCapacity* N/A BIOS.SataSettings.SataPortCCapacity -SataPortCDriveType * N/A BIOS.SataSettings.SataPortCDriveType --SataPortCModel* N/A BIOS.SataSettings.SataPortCModel --SataPortD --sata3 BIOS.SataSettings.SataPortD -SataPortDCapacity* N/A BIOS.SataSettings.SataPortDCapacity -SataPortDDriveType * N/A BIOS.SataSettings.SataPortDDriveType --SataPortDModel* N/A BIOS.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on Dell PowerEdge 13G and later systems. -SataPortGDriveType * N/A BIOS.SataSettings.SataPortGDriveType N/A BIOS.SataSettings.SataPortGModel --sata7 BIOS.SataSettings.SataPortH N/A BIOS.SataSettings.SataPortHCapacity NOTE: The option is supported only on Dell PowerEdge 13G and later systems.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on Dell PowerEdge 13G and later systems. -SataPortHDriveType * N/A BIOS.SataSettings.SataPortHDriveType N/A BIOS.SataSettings.SataPortHModel N/A BIOS.SataSettings.SataPortI N/A BIOS.SataSettings.SataPortICapacity NOTE: The option is supported only on Dell PowerEdge 13G and later systems.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems -SataPortIDriveType N/A BIOS.SataSettings.SataPortIDriveType N/A BIOS.SataSettings.SataPortIModel N/A BIOS.SataSettings.SataPortJ N/A BIOS.SataSettings.SataPortJCapacity N/A BIOS.SataSettings.SataPortJDriveType NOTE: The option is supported only on Dell PowerEdge 13G and later systems. --SataPortIModel NOTE: The option is supported only on Dell PowerEdge 13G and later systems.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on Dell PowerEdge 13G and later systems. --SataPortJModel N/A BIOS.SataSettings.SataPortJModel N/A BIOS.SataSettings.SecurityFreezeLock --ConTerrmType --conterm BIOS.SerialCommSettings.ConTermTy pe -ExtSerialConnector --extserial BIOS.SerialCommSettings.ExtSerialCo nnector --FailSafeBaud --fsbr BIOS.SerialCommSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems -SystemBiosVersion* --biosver BIOS.SysInformation.SystemBiosVersi on -N/A SystemManufacturer * BIOS.SysInformation.SystemManufact urer -N/A SystemModelName* BIOS.SysInformation.SystemModelNa me -SystemServiceTag* BIOS.SysInformation.SystemServiceTa g --svctag/-syssvctag* --SystemMeVersion* N/A N/A NOTE: The option is supported only on Dell PowerEdge 13G and later systems.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems --PowerSaver N/A BIOS.SysProfileSettings.PowerSaver --ProcC1E --cpuc1e BIOS.SysProfileSettings.ProcC1E --ProcCStates --cstates BIOS.SysProfileSettings.ProcCStates --ProcPwrPerf --cpupowermode BIOS.SysProfileSettings.ProcPwrPerf --ProcTurboMode --turbomode BIOS.SysProfileSettings.ProcTurboMo de --SysProfile --profile BIOS.SysProfileSettings.SysProfile -EnergyEfficientTurb o N/A BIOS.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is supported only on Dell PowerEdge 13G and later systems. System Security --AcPwrRcvry --acpower BIOS.SysSecurity.AcPwrRcvry --AcPwrRcvryDelay N/A BIOS.SysSecurity.AcPwrRcvryDelay -N/A AcPwrRcvryUserDela y BIOS.SysSecurity.AcPwrRcvryUserDela y --AesNi N/A BIOS.SysSecurity.Aesni --IntelTxt --inteltxt BIOS.SysSecurity.IntelTxt --NmiButton --nmibutton BIOS.SysSecurity.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems NOTE: The option is not supported on Dell PowerEdge 13G and later systems. --TpmActivation --tpmactivation BIOS.SysSecurity.TpmActivation --tpmclear BIOS.SysSecurity.TpmClear --TpmSecurity --tpmsecurity BIOS.SysSecurity.TpmSecurity --TpmStatus N/A BIOS.SysSecurity.TPMStatus --TpmInfo N/A N/A N/A BIOS.SysProfileSettings.
Group Option on 12G and Later systems Option on Systems Equivalent RACADM Option Prior to 12G Systems -UefiVariableAccess N/A N/A --SecureBoot N/A BIOS.SysSecurity.SecureBoot N/A N/A N/A BIOS.BiosBootSettings.UefiBootSeq NOTE: The option is supported only on Dell PowerEdge 13G and later systems. --SecureBootPolicy NOTE: The option is supported only on Dell PowerEdge 13G and later systems.
location is either slot or embedded (emb), and instance is the numerical position of the device. Some device name examples are shown below. Systems that support a list of device names for boot order can be replicated. Numerical Lists Examples: A:>syscfg --bootseq= 2,3,4,5,1,6 The following devices are set in the boot sequence: Device 2:* usbcdrom.slot.1- USB CD-ROM device Device 3:* virtualcd.slot.1 – VIRTUAL CDROM Device 4:* hdd.emb.0 -Hard drive C: Device 5:* nic.emb.1 - MBA v2.5.
The following devices are set in the boot sequence: Device 4:* nic.emb.1 - IBA GE Slot 0638 v Device 5:* virtual.slot.1 - VIRTUALCDROM DRIVE Device 2: cdrom.emb.0 - IDE CD-ROM device Device 3: hdd.emb.0 - Hard drive C: Device 1: floppy.emb.0 - Diskette drive A: NOTE: The asterisk indicates that the device is enabled in the BIOS.
Example 2: A:>syscfg --devseq= hdd.emb.1,scsiraid.emb.1 The following devices are set in the disk device sequence: Device 1:* hdd.emb.0 - System BIOS boot devices Device 2:* scsiraid.emb.1 - AIC-7899, A:00 Seagate NOTE: The asterisk indicates that the device is enabled in the BIOS. Applicable Systems All PowerEdge systems. Boot Settings You can manage the boot settings using the options in this group.
--HddFailover/--hddfailover Valid Arguments Descriptionoff • On systems prior to 12G: off, on • On 12G and later systems: Enabled, Disabled Specifies the device in the Hard Disk Drive Sequence menu that has not been attempted in the boot sequence. When set to on, all devices are attempted in an order in which they are configured. When set to off, only the first device in the hard disk sequence is attempted. This option can be replicated.
Integrated Devices You can use the options in this group to manage the integrated devices such as internal NIC and integrated USB. --EmbNic1/--embnic1 Valid Arguments Description • On systems prior to 12G: on, off, onnopxe, onwithiscsi • On 12G and later systems: Enabled, EnabledPxe, EnablediScsi, Disabled Turns the first embedded NIC on with PXE on, off, or on without PXE enabled. This option is only valid for supported systems that have a NIC.
order. If the NIC is turned on with PXE, it is placed at the end of the boot order. The onnopxe argument is not supported on all systems. The onwithiscsi argument enables the embedded NIC to boot from the iSCSI server. The embnic1 option can be replicated.
• Description On 12G and later systems: Enabled, EnabledPxe, EnablediScsi, Disabled Turns the fourth embedded NIC on with PXE enabled, off, or on without PXE enabled. This option is only valid for supported systems that have four embedded NICs. If the fourth NIC is enabled without PXE, it is not found in the boot order. If the fourth NIC is turned on with PXE, it is placed at the end of the boot order. The onnopxe argument is not supported on all systems. This option can be replicated.
• Description On 12G and later systems: Enabled, DisabledOs Enables or disables Integrated Network 1. NOTE: If set to DisabledOs, the Integrated NICs may still be available for shared network access by the embedded management controller. This function must be configured through the NIC management utilities provided with your system.
--IntegratedSas/--integratedsas Valid Arguments Description • On systems prior to 12G: enable, disable • On 12G and later systems: Enabled, Disabled Enables or disables the integrated SAS controller. This option can be replicated. Example: A:>syscfg --integratedsas=enable integratedsas=enable Applicable Systems All PowerEdge systems.
--InternalUsb/--internalusb Valid Arguments Description • On systems prior to 12G: off, on • On 12G and later systems: On, Off Turns the internal USB port on or off. Example: A:>syscfg --internalusb=on internalusb=on Applicable Systems All PowerEdge systems. --InternalUsb1/--internalusbport1 Valid Arguments Description • On systems prior to 12G: on, off • On 12G and later systems: On, Off Turns the internal USB port 1on or off.
Example: A:>syscfg --oswatchdogtimer=enable oswatchdogtimer=enable Applicable Systems All PowerEdge systems. --SriovGlobalEnable/--sriov Valid Arguments Description • On systems prior to 12G: enable, disable • On 12G and later systems: Enabled, Disabled Enables or disables support for Single Root I/O Virtualization (SR-IOV) devices. Example: A:>syscfg --sriov=disable sriov=disable Applicable Systems All PowerEdge systems.
--Usb3Setting Valid Arguments • • Description Enables or disables the USB 3.0 port. On systems prior to 13G: NA On 13G and later systems: Auto, Enabled, Disabled • Auto —USB ports operate at USB 2.0 speed. • Enabled—USB ports operates at USB 3.0 speed. • Disabled—USB 3.0 host controller is disabled and the speed is set to USB 2.0.
• Description On 12G and later systems: Enabled, Disabled Enables or disables the Preboot Execution Environment (PXE) device. When enabled, an Unified Extensible Firmware Interface (UEFI) boot option is created for the PXE device. NOTE: The value of n in PxeDevnEnDis can be 1–4.
Example: A:>syscfg --PxeDev1VlanEnDis=Enabled PxeDev1VlanEnDis=Enabled Applicable Systems PowerEdge 12G and later systems --PxeDevnVlanId Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Sets the virtual LAN (VLAN) of the PXE device. NOTE: The value of n in PxeDevnVlanId can be 1–4.
Example: A:>syscfg --CorrEccSmi=Enabled CorrEccSmi=Enabled Applicable Systems PowerEdge 12G and later systems --DynamicCoreAllocation Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Enables or disables the operating system capability to maintain the logical processors in the idle state to reduce power consumption.
• Description On 12G and later systems: AutoVolt, Volt15V Sets the DIMM voltage selection. When set to AutoVolt(default value), the system automatically sets the voltage to the optimal setting based upon the DIMM capability and the installed DIMM population. This option also enables setting the system DIMM voltage to a higher (1.5V) setting if the DIMMs support multiple voltages and have been set to a lower voltage. NOTE: Volt15V represents 1.5 Volt.
--redmem Valid Arguments off, spare, mirror, DDDC Description Allows selection of the required redundant memory mode, or disables redundant memory. This option can be replicated. Example: A:>syscfg --redmem=off redmem=off Applicable Systems PowerEdge systems with Intel Xeon 7500 series processor --SerialDbgOut Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Enables or disables the RC/MRC Serial debug output.
Applicable Systems All PowerEdge systems. --SysMemSpeed* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the clock frequency of the main memory. Example: A:>syscfg --SysMemSpeed Applicable Systems PowerEdge 12G and later systems. --SysMemType* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the type of main memory installed in the system.
--ClusterOnDie Valid Arguments • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Description Enables or disables the Cluster On Die option. When enabled, the feature enhances the performance of the system with two caching agents. A:>syscfg --ClusterOnDie=Enabled ClusterOnDie=Enabled Applicable Systems PowerEdge 12G and later systems Miscellaneous Settings You can manage the miscellaneous settings using the options in this group.
-- InSystemCharacterization Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: FastBoot, OptimizedBoot, Disabled In-System Characterization (ISC) runs during power-on self-test (POST) on detecting relevant changes in the system configuration to optimize power and performance. ISC takes about 20 seconds to run, and a system restart is required to apply the system configuration changes.
-- InSystemCharacterization Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: FastBoot, OptimizedBoot, Disabled In-System Characterization (ISC) runs during power-on self-test (POST) on detecting relevant changes in the system configuration to optimize power and performance. ISC takes about 20 seconds to run, and a system restart is required to apply the system configuration changes.
Applicable Systems PowerEdge 12G and later systems. --OneTimeBootSeqDev/--nextboot Valid Arguments Description • On systems prior to 12G: (from the bootseq option device list) • On 12G and later systems: numerical list separated by commas or list of device names separated by commas Sets the specified device as the first device in the boot order for the next boot cycle only. The device must be a device from the bootseq option device list.
Example: A:>syscfg --OneTimeHddSeqDev= 2,3,4,5,1,6 The following devices are set in the boot sequence: Device 2:* usbcdrom.slot.1- USB CD-ROM device Device 3:* virtualcd.slot.1 – VIRTUAL CDROM Device 4:* hdd.emb.0 -Hard drive C: Device 5:* nic.emb.1 - MBA v2.5.12 Slot 0500 Device 1:* virtualfloppy.slot.1 - VIRTUAL FLOPPY Device 6:* usbfloppy.slot.1 - USB Floppy device NOTE: The asterisk indicates that the device is enabled in the BIOS. Applicable Systems PowerEdge 12G and later systems.
--DataReuse/--datareuse Valid Arguments Description • On systems prior to 12G: enable, disable • On 12G and later systems: Enabled, Disabled Enables (default value) or disables data reuse in cache. Set to enable for High Performance Computing (HPC) applications. Set to disable for energy efficiency. This option can be replicated.
processor per core. Each processor core supports maximum two logical processors. This option is available on all systems that support logical processing (Hyperthreading). This option can be replicated. Example: A:>syscfg --logicproc=enable logicproc=enable Applicable Systems All PowerEdge systems. --Proc1Brand* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the brand text provided by the processor manufacturer.
--Proc1L3Cache* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the amount of memory in the corresponding processor cache. Example: A:>syscfg --Proc1L3Cache Applicable Systems PowerEdge 12G and later systems. --Proc1NumCores* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the number of cores in the processor package..
--Proc2L2Cache* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the amount of memory in the corresponding processor cache. Example: A:>syscfg --Proc2L2Cache Applicable Systems PowerEdge 12G and later systems. --Proc2L3Cache* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the amount of memory in the corresponding processor cache.
--Proc3Id* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the family, model, and stepping values of the processor. Example: A:>syscfg --Proc3Id Applicable Systems PowerEdge 12G and later systems. --Proc3L2Cache* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the amount of memory in the corresponding processor cache.
--Proc4Brand* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the brand text provided by the processor manufacturer. Example: A:>syscfg --Proc4Brand Applicable Systems PowerEdge 12G and later systems. --Proc4Id* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the family, model, and stepping values of the processor.
--Proc4NumCores* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the number of cores in the processor package.. Example: A:>syscfg --Proc4NumCores Applicable Systems PowerEdge 12G and later systems. --Proc64bit* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Specifies if the installed processor supports 64-bit extensions or not..
Applicable Systems PowerEdge 12G and later systems. --ProcCores/--cpucore Valid Arguments Description • On systems prior to 12G: 1, 2, 4, 6, 8, 10, 12, 14, 16, all • On 12G and later systems: single, all, dual, quad, 1, 2, 4, 6, 8, 10, 12, 14, 16, 18 Controls the number of enabled cores in each processor. The default value is set to the maximum number of cores per processor. The number of cores depends on the processor.
• Description On 12G and later systems: Enabled, Disabled Enables or disables the hardware prefetcher. Processor preempts what data might be needed next, when set to enable. When some data is found, it loads several steps in advance. Processor does not preempt, when set to disable. This option can be replicated. Example: A:>syscfg --hwprefetcher=enable hwprefetcher=enable Applicable Systems All PowerEdge systems.
--QpiSpeed Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: MaxDataRate, 9GTps, 8GTps, 7GTps, 6GTps Sets the speed of the processor.
• Description On 13G and later systems: Nominal, Level1, Level2 Configures the Thermal Design Power (TDP). Example: A:>syscfg --ProcConfigTdp=Nominal ProcConfigTdp=Nominal --ProcX2Apic Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Enables or disables the x2APIC mode.
• Description On 12G and later systems: Off, Auto Sets the embedded SATA port1 to auto or off. Example: A:>syscfg --eSataPort1=Off eSataPort1=Off Applicable Systems Dell PowerEdge 12G and later systems. --eSataPort1Capacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive. This option is undefined for removable-media devices such as optical drives.
• Description On 12G and later systems: Off, Auto Sets the drive type of the selected device to off or auto This option can be replicated. Example: A:>syscfg --sata0=auto sata0=auto Applicable Systems All PowerEdge systems --SataPortACapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive. This option is undefined for removable-media devices such as optical drives.
--SataPortB/--sata1 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Auto, Off Turns the SATA port 1 to auto or off. This option can be replicated. Example: A:>syscfg --sata1=auto sata1=auto Applicable Systems All PowerEdge systems --SataPortBCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortC/--sata2 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 2 to auto or off. This option can be replicated. Example: A:>syscfg --sata2=auto sata2=auto Applicable Systems All PowerEdge systems --SataPortCCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortD/--sata3 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Auto, Off Turns the SATA port 3 to auto or off. This option can be replicated. Example: A:>syscfg --sata3=auto sata3=auto Applicable Systems All PowerEdge systems. --SataPortDCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortE/--sata4 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 4 to auto or off. This option can be replicated. Example: A:>syscfg --sata4=auto sata4=auto Applicable Systems All PowerEdge systems. --SataPortECapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortF/--sata5 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 5 to auto or off. This option can be replicated. Example: A:>syscfg --sata5=auto sata5=auto Applicable Systems All PowerEdge systems. --SataPortFCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortG/--sata6 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 6 to auto or off. This option can be replicated. Example: A:>syscfg --sata6=auto sata6=auto Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --SataPortGCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortH/--sata7 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 7 to auto or off. This option can be replicated. Example: A:>syscfg --sata7=auto sata7=auto Applicable Systems All PowerEdge systems. --SataPortHCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortI/--sata7 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 7 to auto or off. This option can be replicated. Example: A:>syscfg --sata7=auto sata7=auto Applicable Systems All PowerEdge systems. --SataPortICapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SataPortJ/--sata7 Valid Arguments Description • On systems prior to 12G: auto, off • On 12G and later systems: Off, Auto Turns the SATA port 7 to auto or off. This option can be replicated. Example: A:>syscfg --sata7=auto sata7=auto Applicable Systems All PowerEdge systems. --SataPortJCapacity* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the total capacity of a hard-disk drive.
--SecurityFreezeLock Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Sends the Security Freeze Lock command to the embedded SATA drives during power-on self-test (POST). The option is applicable only to ATA and AHCI, and not to RAID.
When set to rad , the external serial connector is routed to the remote access device interface. Terminal escape sequences can toggle the external connector between the system (COM2) and the remote access device. This option can be replicated. Example: A:>syscfg --extserial=com1 extserial=com1 The --serialcomm option can be used with the external serial (-extserial) option instead of the --conred (available on systems earlier than PowerEdge 9G systems) option.
• Description On 12G and later systems: OnNoConRedir, OnConRedirCom1, OnConRedirCom2, Off Enables or disables the serial communication devices (Serial Device 1 and Serial Device 2) in BIOS. Example: A:>syscfg --SerialComm=OnNoConRedir SerialComm=OnNoConRedir Applicable Systems All PowerEdge 12G and later systems.
System Information You can view the system configuration details using the options in this group. --SysMfrContactInfo* Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: read-only Displays the information for contacting the Original Equipment Manufacturer (OEM) of this system.
Example: A:>syscfg --SystemModelName Applicable Systems PowerEdge 12G and later systems. --SystemServiceTag/--svctag/--syssvctag* Valid Arguments Description • On systems prior to 12G: read-only • On 12G and later systems: read-only Displays the system service tag (a unique identifier assigned by the Original Equipment Manufacturer (OEM) of this system). NOTE: The syssvctag option reports the system service tag on a Blade system.
--CollaborativeCpuPerfCtrl Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled When set to Enabled, the operating system demand based power management (OS DBPM) and system demand based power management (System DBPM) controls the CPU power management. This feature can be enabled only when CPU power management (ProcPwrPerf) is set to system DBPM in Custom mode.
--MemRefreshRate Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: 1x, 2x Sets the Memory Refresh Rate as 1x or 2x Example: A:>syscfg --MemRefreshRate=1x MemRefreshRate=1x Applicable Systems PowerEdge 12G and later systems. --MemVolt Valid Arguments • On systems prior to 12G: NA • On 12G and later systems: AutoVolt, Volt15V, Volt135V NOTE: Volt15V represents 1.5 Volt and Volt135V represents 1.35 Volt. Description Sets the DIMM voltage selection.
• Description On 13G and later systems: Enabled, Disabled Enables or disables the power saving Dell Active Power Controller (DAPC) algorithm. Example: A:>syscfg --PowerSaver=Enabled PowerSaver=Enabled Applicable Systems PowerEdge 13G and later systems --ProcC1E/--cpucle Valid Arguments Description • On systems prior to 12G: enable, disable • On 12G and later systems: Enabled, Disabled Enables or disables C1-E. By default, it is enabled. This option can be replicated.
Example: A:>syscfg --ProcPwrPerf=OsDbpm ProcPwrPerf=OsDbpm Applicable Systems All PowerEdge systems. --ProcTurboMode/--turbomode Valid Arguments Description • On systems prior to 12G: enable, disable • On 12G and later systems: Enabled, Disabled Enables or disables core-based turbo mode. Turbo mode is a feature on Intel processors that allows one processor core to increase the frequency by one bin whenever the other core has gone into an idle state.
Example: A:>syscfg --EnergyEfficientTurbo=Enabled EnergyEfficientTurbo=Enabled Applicable Systems PowerEdge 13G and later systems --ProcnTurboCoreNum Valid Arguments Description • On systems prior to 13G: NA • On 13G and later systems: All, 1, 2, 4, 6, 8, 10, 12, 14, 16, 18 Sets the number of Turbo Boost-enabled cores for a processor. By default, the maximum number of cores per processor is enabled. NOTE: The value of n in ProcnTurboCoreNum can be 0–3.
System Security You can manage the system security properties of the BIOS using the options in this group. --AcPwrRcvry/--acpower Valid Arguments Description • On systems prior to 12G: on, off, last • On 12G and later systems: On, Off, Last Sets the behavior for the system after AC power is lost. This option specifies how the system responds to the restoration of AC power and is particularly useful in systems that are turned off using a power strip.
Applicable Systems PowerEdge 12G and later systems --AesNi Valid Arguments Description • On systems prior to 12G: NA • On 12G and later systems: Enabled, Disabled Displays the current status of Intel Processor AES-NI feature.
Example: A:>syscfg --nmibutton=enable nmibutton=enable Applicable Systems PowerEdge 11G and later systems --PasswordStatus/--pwdlock Valid Arguments Description • On systems prior to 12G: lock, unlock • On 12G and later systems: Locked, Unlocked Locks the system password. To prevent the system password from being modified, set this option to lockedand enable setup password. This field also prevents the system password from being disabled by the user while the system boots.
Example: A:>syscfg --setuppwd=asetuppassword The password has been set. Please use a warm reboot to apply the password to the system. Example 2: A:>syscfg --setuppwd=asetuppassword -oldsetuppwd=currentpassword The password has been set. Please use a warm reboot to apply the password to the system. Example 3: A:>syscfg --setuppwd=asetuppassword -oldsetuppwd=currentpassword The old password entered is incorrect. The new password will not be set. Please try again.
• Description On 12G and later systems: read-only Displays the current revision of the Complex Programmable Logic Device (CPLD) of the system. Example: A:>syscfg --SystemCpldVersion Applicable Systems PowerEdge 12G and later systems --TcmActivation/--tcmactivation Valid Arguments Description • On systems prior to 12G: enabled, disabled, and nochange • On 12G systems: NoChange, Activate, Deactivate Allows the user to change the operational state of the Trusted Cryptography Module (TCM).
• On 12G and later systems: On, Off Controls the reporting of the Trusted Cryptography Module (TCM) in the system. Description NOTE: The tcmsecurity option is a sub-option of tcm. Example: A:>syscfg --tcmsecurity=on tcmsecurity=on Applicable Systems All PowerEdge systems.
--TpmSecurity/--tpmsecurity Valid Arguments Description • On systems prior to 12G: off, onwithpbm, onwithoutpbm • On 12G and later systems: Off, OnPbm, OnNoPbm Controls the reporting of the Trusted Platform Module (TPM) in the system. NOTE: The tpmsecurity option is a sub-option of tpm. Example: A:>syscfg --tpmsecurity=off tpmsecurity=off Applicable Systems All PowerEdge systems.
• — Commands are not sent to the TPM. Activate — TPM is enabled. • Deactivate — TPM is disabled. • Clear — All the contents of TPM are cleared. NOTE: This field is read-only when TpmSecurityis set to Off. CAUTION: Clearing TPM results in loss of all keys in the TPM. This could affect booting to operating system.
• Description On 13G and later systems: Standard, Controlled Secures the UEFI variables. When set to Standard, the UEFI variables are accessible from the operating system as per the UEFI specification. When set to Controlled, selected UEFI variables are protected in the operating system and new UEFI boot entries are pushed to the end of the current boot order.
Table 7. DTKTORACADM Command on Windows Operating System Valid Arguments dtktoracadm.exe or dtktoracadm.exe windows_scripts.lst debug Description On systems running Windows operating system, run the command, where windows_scripts.lst is the input file which contains the list of path to run the RACADM scripts and debug is an option which list the file status. Applicable Systems All PowerEdge 12 and later systems. Table 8.
Group SYSCFG Commands Equivalent RACADM Commands --linklocaladdrv6 iDRAC.IPv6.LinkLocalAddress --prefixlengthv6 iDRAC.IPv6.PrefixLength --connectionmode iDRAC.IPMISerial.ConnectionMode --msgcommbitrate iDRAC.IPMISerial.BaudRat --msgcommflowctrl iDRAC.IPMISerial.FlowControl --tmcfghandshakectrl iDRAC.IPMISerial.HandshakeControl --tmcfglineediting iDRAC.IPMISerial.LineEdit --tmcfgnewlineseq iDRAC.IPMISerial.NewLineSeq --solcharaccuminterval iDRAC.IPMISOL.
Group SYSCFG Commands Equivalent RACADM Commands --ErrPrompt BIOS.MiscSettings.ErrPrompt --NumLock BIOS.MiscSettings.NumLock --ForceInt10 BIOS.MiscSettings.ForceInt10 --DcuIpPrefetcher BIOS.ProcSettings.DcuIpPrefetcher --DcuStreamerPrefetcher BIOS.ProcSettings.DcuStreamerPrefetcher --LogicalProc BIOS.ProcSettings.LogicalProc --ProcExecuteDisable BIOS.ProcSettings.ProcExecuteDisable --ProcHwPrefetcher BIOS.ProcSettings.ProcHwPrefetcher --ProcVirtualization BIOS.ProcSettings.
--assignintr Valid Arguments standard, distributed Description Controls the interrupt assignment of PCI devices in the system. This option is set to standard by default, causing standard interrupt routing that uses interrupt A, B, C, and D for all PCIe devices. When set to distributed, the interrupt routing is swizzled at the MCH root ports to minimize sharing of interrupts across all PCIe (and PCI-X in the Programmable Interrupt Controller (PIC) mode) devices.
Applicable Systems All PowerEdge systems prior to PowerEdge 12Gsystems --coreperformanceboost Valid Arguments enable, disable Description Enables or disables the AMD Core Performance Boost feature. When enabled, it allows higher performance power states if additional power is available to the CPU. This option can be replicated.
Example: A:>syscfg --embideraid=on embideraid=on Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems --embnic1pxe Valid Arguments enable, disable Description Enables or disables Preboot Execution Environment (PXE) on the first embedded NIC. If PXE is disabled, the first NIC is not found in the boot order. If PXE is enabled, the first NIC is placed at the end of the boot order. This option is only present on systems that do not support the embnic1 option.
--embscsi1 Valid Arguments on, off Description Turns the first embedded SCSI controller. This option is only valid for supported systems that have an embedded SCSI controller. This option can be replicated. Example: A:>syscfg --embscsi1=on embscsi1=on Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems --embscsi2 Valid Arguments on, off Description Turns the second embedded SCSI controller. This option is only valid for supported systems that have an embedded SCSI controller.
--embscsiraidchb Valid Arguments raid, scsi Description Sets the second channel on an embedded RAID controller to SCSI or RAID. This option is only valid for systems that support RAID/RAID and RAID/SCSI settings for channels A and B. This option can be replicated.
--redmem Valid Arguments off, spare, mirror, DDDC Description Allows selection of the required redundant memory mode, or disables redundant memory. This option can be replicated. Example: A:>syscfg --redmem=off redmem=off Applicable Systems PowerEdge systems with Intel Xeon 7500 series processor power Valid Arguments NA Description For details about the power suboptions and arguments, see Sub Options For Power Option.
Option Sub-option Arguments Description If power profiles are not available on the platform, an error message is displayed. A:>syscfg power-profile=maxperformance -setuppwdoverride custom Creates the custom profile. Reboot the system for the settings to take effect. A:>syscfg power --profile=custom --setuppwdoverride --cpupowermode min, max, osdbpm, Allows you to set the CPU power and performance management to minimum systemdbpm power, maximum performance, operating system DBPM, or system DBPM mode.
Option Sub-option Arguments Description is the limit for power consumption in Watts, or btuphr, or percent. The value of must be between the maximum and minimum threshold values, else an error is displayed. If the value is less than the minimum threshold value, a warning message appears. is the unit of the value and can be watt, or btuphr, or percent. If the unit is btuphr, it is converted in to Watts using the formula Watt = BTU/hr /3.413.
Sub Options And Arguments For tcm Option Option Sub-option Arguments Description tcm --tcmsecurity off Does not report the presence of TCM to the operating system. on Reports the presence of TCM to the operating system. Example: A:>syscfg tcm --tcmsecurity=off -tcmactivation enabled Enables and activates the TCM feature. disabled Disables and deactivates the TCM feature. nochange Does not alter the operational state of the TCM feature.
Option Sub-option Arguments Description onwithoutpbm Directs the BIOS to bypass the preboot measurements. Example: A:>syscfg tpm -tpmsecurity=onwithoutpbm --setuppwdoverride -tpmactivation enabled Enables and activates the TPM feature. disabled Disables and deactivates the TPM feature. nochange Does not alter the operational state of the TPM feature. Example: A:>syscfg tpm -tpmactivation=enabled -setuppwdoverride NOTE: You cannot set tpmactivation when tpmsecurity is set to off.
Option Sub-option Arguments Description Example: A:>syscfg tpm -tpmactivation=enabled -undotpmclear --setuppwdoverride --valsetuppwd Validates the setup password for TPM authentication. If you try to change DTK settings, you are prompted to enter this password to access the settings. For more information on delimiters, see Command Line Option Delimiters.
bmcversion Table 10. bmcversion options Option Sub-option Valid Arguments Description Displays the version information for the BMC and the BMC firmware. This option cannot be replicated. bmcversion --devid NA Reports the BMC device ID. --devrevision NA Reports the BMC device revision. -majorfwversion NA Reports the BMC device major firmware revision. -minorfwversion NA Reports the BMC device minor firmware revision.
controlpanelaccess Option Sub-option Valid Arguments Description --controlpanelaccess NA viewandmodify , viewonly, disabled Sets or gets the access level for the Liquid Crystal Display (LCD). Example: A:>syscfg -controlpanelaccess= viewandmodify controlpanelaccess= viewandmodify deviceguid* Option Sub-option Valid Arguments Description --deviceguid* NA NA Displays the GUID for the BMC. This option cannot be replicated.
Example: A:>syscfg --fiberchannel=enable fiberchannel=enable Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --floppy Option --floppy Valid Arguments auto, off, readonly Description Sets the diskette drive controller to auto, off, or readonly. This option is available on all supported systems that have a supported diskette drive.
Example: A:>syscfg --hddfailover=on hddfailover=on Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --hpcmode Valid Arguments enable, disable Description Enables or disables the High Performance Computing (HPC) Mode. When set to enable, the HPC is enabled utilizing only the high frequency P-State settings. When set to disable (default value), all PStates inherent to the CPU are used.
Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --idracgui Valid Arguments enable, disable Description Enables and disables the iDRAC GUI. This option can be replicated. Example: A:>syscfg --idracgui=disable idracgui=disable Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --lpt Valid Arguments lpt1, lpt2, lpt3, disable Description Configures or reports the I/O address of the LPT (parallel) port.
Example: A:>syscfg --memintleave=enable memintleave=enable NOTE: The memintleave option is same as Nodeinterleave option. For more information, see Memory Settings group. Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --memremap Valid Arguments off, auto Description Sets the memory remapping to off or auto. Example: A:>syscfg --memremap=off memremap=off Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems.
CAUTION: When changing a RAID controller from SCSI to RAID or from RAID to SCSI, data is lost on the affected hard drives. The warning message for this data is not displayed if you use the --noraidprompt option. To avoid data loss, back up any information on the hard drives before changing the type of controller used with the drives Example: A:>syscfg --embscsiraid=raid --noraidprompt embscsiraid=raid Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems.
Example 2: A:>syscfg --syspwd= -oldsyspwd= The old password entered is incorrect. The new password will not be set. Please try again. Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --opticaldrivectrl Valid Arguments enable, disable Description Enables or disables the optical CD-ROM controller. Example: A:>syscfg --opticaldrivectrl=enable opticaldrivectrl=enable Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems.
--serial1 Valid Arguments disable, com1, com3, com1_bmc, bmcserial, bmclan, rac Description Configures or reports the first serial port communication port. This option can be replicated. • • • • bmcserial — maps serial port 1 to BMC Serial. bmclan — routes the serial traffic destined for serial1 out to NIC1. com1_bmc — maps serial port 1 to COM port 1 BMC. rac — maps serial port 1 to the RAC device.
Example: A:>syscfg --sma=disable sma=disable Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --sysrev* Valid Arguments read-only Description Reports the system revision. Applicable Systems All PowerEdge systems prior to PowerEdge 12G systems. --usb Valid Arguments on, legacy, off Description Sets or reports the status of the USB port. When set to on, USB keyboards and mice function only for systems with operating systems that have native USB support.
--vflash Valid Arguments enable, disable Description Enables or disables vflash on iDRAC. Example: A:>syscfg --vflash=enable vflash=enable Applicable Systems All PowerEdge 11G systems or systems with iDRAC6 identify Valid Arguments 0–254 Description Flashes the identification LED for a specified number of seconds. NOTE: Use 0 to stop the blinking of the LED.
kvmstatusonlcd Option Suboption -NA kvmstatusonlc d Valid Description Arguments active, inactive Applicable Systems Configures the Dell Virtual KVM (vKVM) session status on the LCD. PowerEdge 11G systems Example: A:>syscfg -kvmstatusonlcd=active kvmstatusonlcd=active lancfgparams Option Sub-option Valid Arguments Description Configures and displays LAN configuration parameters. This option can be replicated.
Option Sub-option Valid Arguments Description NOTE: FQDN is applicable only for destipaddr option and is supported only on PowerEdge 12G systems. Example 1 (to set the destination IP address): A:>syscfg lcp --alertdest=1 --destipaddr=192.168.100.15 Example 2 (to set the destination IP address as FQDN): A:>syscfg lcp --alertdest=1 --destipaddr=xxx.yyy.com --alertdest 1, 2, 3, 4 Sets the destination for the LAN alert. This sub-option can be replicated.
Option Sub-option Valid Arguments Description -nicselectionfailover none, lom1, lom2, lom3, lom4, all Sets the operating mode of the NIC selection failover to none, lom1, lom2, lom3, lom4, or all. Some of these options are not applicable on certain systems. due to underlying hardware. NOTE: This option is available only with the appropriate installed license. NOTE: This option is applicable on PowerEdge 12G systems.
Option Sub-option Valid Arguments Description Example 1 (to display the current LAN configuration settings): A:>syscfg --lancfgparams destipaddr=192.168.100.15 vlantag=enable vlanid=1000 vlanpriority=7 macaddress=0:6:5b:fb:c8:a7 commstring=public ipaddrsrc=static ipaddress=192.168.100.10 subnetmask=255.255.255.0 gateway=192.168.100.1 Example 2 (to set the LAN configuration parameters): A:>syscfg --lancfgparams --destipaddr=192.168.100.
Option Sub-option Valid Arguments Description --ipmioverlan disable, alwaysavail Sets the LAN channel access mode. This sub-option can be replicated. --channelprivlmt user, operator, administrator Sets the maximum privilege level accepted for the LAN channel. This sub-option can be replicated.
Option Sub-option Valid Arguments Description Example 1 (to enable User ID 2 on the LAN channel with administrator privileges): A:>syscfg lanuseraccess -userid=2 -usrprivlmt=administrator Example 2 (to enable User ID 4 on the LAN channel with user privileges): A:>syscfg lanuseraccess -userid=4 --usrprivlmt=user lcd1 Option Sub-option Valid Arguments Description --lcd1 NA Sets the first line of user-defined text on the system LCD. This option can be replicated.
Option Sub-option Valid Arguments Description Example: A:>syscfg --loaddefaults Loading defaults... nextboot Option Sub-option Valid Arguments Description --nextboot or -OneTimeBootSeqDev NA valid device name (from the bootseq option device list) Sets the specified device as the first device in the boot order for the next boot cycle only. The device must be a device from the bootseq option device list. Run the bootseq option to see a list of available device names.
passwordaction Option Sub-option Valid Arguments Description Configures and tests the password for the specified User ID. This option cannot be replicated. All three suboptions, action, userid, and password must be included in the command line. passwordaction NOTE: This option does not support 20 byte passwords. --userid 2–16, if your Specifies the BMC User ID. This subsystem has a DRAC option cannot be replicated.
Option Sub-option Valid Arguments Description redundegraded ,redunlost, procwarn, procfail, powerwarn, powerfail, hardwarelogfa il, autorecovery, batterywarn, batteryfail, powerabsent, procabsent, systempowerwa rn, systempowerfa il --filteraction powercycle, reset, powerdown, power reduction, none Sets the event filter action for the filter specified using the filter suboption. This sub-option depends on the filter sub-option. This suboption can be replicated.
Option Sub-option Valid Arguments Description Example 1 (To configure the PEF so that the system is powered down in response to a fan failure event): A:>syscfg pefcfgparams -filter= fanfail-filteraction=powerdown pefcfgparams filter=fanfail filteraction=powerdown Example 2 (To configure the PEF so that a PEF alert is not sent to the destination IP address in response to a chassis intrusion event): A:>syscfg pefcfgparams -filter= intrusion-filteralert=disable pefcfgparams filter= intrusion filteralert=dis
Option Sub-option Valid Arguments Description NOTE: This option applies only to PowerEdge systems that are configured with a BMC. NOTE: This argument requires ACPI support to function properly. racreset* Option Sub-option Valid Arguments Description --racreset* NA NA Resets the RAC. It cannot be accompanied with any other option. This option cannot be replicated. serialcfgparams Option Sub-option Valid Arguments Description Configures and displays serial configuration parameters.
Option Sub-option Valid Arguments Description --tmcfgnewlineseq noterm, crlf, null, cr, lfcr,1f Sets the new line sequence value for terminal mode configuration. This sub-option can be replicated. -cr, null tmcfginputnewline seq Sets the input new line sequence value for terminal mode configuration. This sub-option can be replicated.
Option Sub-option Valid Arguments Description privilege level set to administrator): A:>syscfg serialchannel access -ipmioverserial=disable -channelprivlmt=administra tor serialchannelaccess ipmioverserial=disable channelprivlmt=administra tor serialchannelinfo Option Sub-option Valid Arguments Description Displays media and protocol information about the serial channel. This option cannot be replicated. -serialchannelinfo or sci --mediumtype NA Displays the medium type for the serial channel.
Option Sub-option Valid Arguments Description ID for the serial channel. This option can be replicated. --userid 2–16, if your Sets the User ID. This subsystem has a DRAC option can be replicated. 5 controller --usrprivlmt user, operator, administrator, noaccess Sets the maximum BMC user privilege level for the serial channel for the User ID specified using the userid sub-option. This sub-option can be replicated. This suboption is dependent on the userid sub-option.
solaction Option Sub-option Valid Arguments Description This option enables or disables SerialOver- LAN (SOL) access for a particular user. This option can be replicated. solaction Example: A:>syscfg solaction --userid=2 --action=disable solaction userid=2 action=disable --userid 2–16, if your Specifies the BMC user ID. This subsystem has a DRAC option can be replicated. 5 controller --action enable, disable Enables or disables the user ID specified using the userid sub-option.
Option Sub-option Valid Arguments Description --solbitrate 9600, 19200 Sets the serial channel communication bit rate (in bps) with the BMC when SOL is activated. This option can be replicated. NOTE: The arguments for solbitrate vary with various Dell systems. If an argument valid for a particular Dell system is entered for another system, the Parameter out of range error is displayed.
Option Sub-option Valid Arguments Description -currentactivessns NA Displays the number of currently active sessions on all channels of the BMC. This sub-option cannot be replicated. Example: A:>syscfg ssninfo currentactivessns=1 maxactivessns=4 useraction Option Sub-option Valid Arguments Description Enables and disables BMC, sua, and lua user IDs. This option can be replicated. useraction --userid 2–16, if your Specifies the BMC user ID. This subsystem has a DRAC option can be replicated.
Option Sub-option Valid Arguments Description Example 1( to configure User ID 3 with a user name ): A:>syscfg username --userid=3 --name=bmcmaster username userid=3 name=bmcmaster Example 2 (to display the username for User ID 3): A:>syscfg username --userid=3 --name username userid=3 name=bmcmaster version* Option Sub-option Valid Arguments Description --version* NA NA Displays the version information for the SYSCFG utility.
Option Valid Arguments Description -b or --byte Specifies a value to write to state data. The format of the argument must be in decimal format unless the -x option is given. If the -x option is given, the value is interpreted as hexadecimal format. The value can optionally contain 0x. The decimal range is 0–255, and the hexadecimal range is 0x00– 0xFF. Example: A:>syscfg -b 1 The state byte has been set to 1. A:>syscfg -b 2 -x The state byte has been set to 0x02.
Table 11. SYSCFG Options and Arguments for System Configuration Option Valid Arguments Description --asset None Reports the customer-programmable asset tag number for a system. This option displays the asset tag for a system. For Blade systems, the SYSCFG utility reports the asset tag for both the server module and the asset tag for its chassis. For more information on delimiters, see Command Line Option Delimiters .
Option Valid Arguments Description Example: A:>syscfg --envfile sys.ini DELLNIC1=INTEL PRO100 DELLNIC2=INTEL PRO100 DVIDEO1=RAGEXL DIDE1=PEQUR/ROSS IDE DSCSI1=AIC-7899 --mem* None Reports the amount of system memory physically installed in the system, not the amount of memory available to an operating system. If used with the -s option, the environment variable is set to the amount of system memory. The last two characters of the memory value indicate the order of magnitude used (KB or MB).
Option Valid Arguments Description current working directory, the directory containing the SYSCFG executable is searched. If the -n option is used to specify a filename, this filename is used for resolution. If a specific filename is not given and the pci.ids file cannot be found, Unknown is printed for all vendor and device codes. For more information, see PCI Reporting. Example 1 (the pci.ids filename is specified in the command line instance ): A:>syscfg -n pci.
Option Valid Arguments Description None Example 3 (a pci.
Option Valid Arguments Description Example: A:>syscfg --svctag svctag=113CD1S --sysasset* None Reports the system asset tag on Blade systems. Example: A:>syscfg --sysasset sysasset=ASSET01 --sysid* None Reports the unique system id bytes for a server. Servers contain a unique ID value based on their model. The ID value is reported as a hexadecimal value with a leading 0x, lowercase hexadecimal letters, and zero-padded to 2 bytes.
SYSCFG For IPv6 Configuration The following table lists all valid options and arguments for IPv6 configuration along with a description of each option. These options are applicable only if the DRAC on your system supports IPv6. NOTE: This option is available only if appropriate license is installed. Option Sub-option Valid Arguments Description lancfgparam sv6 or lcpv6 --ipv6 enable, disable Enables or disables the IPv6 stack.
PCI Reporting The scan of the PCI bus uses a file to resolve PCI vendor and device codes to vendor information strings. The format of the PCI output is as follows: PCI Bus: 2, Device: 4, Function: 0 Vendor: 8086 - Intel Corp. Device: 1229 - 82557/8/9 [Ethernet Pro 100] Sub Vendor:8086 - Intel Corp.
environment variable that is set to the value of the name/value pair whose name matches the system ID. To change the name of the environment variable, change the value of the MACHINE name in the Variable Names section, and change the corresponding section name.
RAIDCFG 5 This section documents the Deployment Toolkit (DTK) RAID configuration utility. The RAIDCFG utility provides a single command line tool that can configure all supported RAID controllers. Features The RAID configuration utility: • Displays help and usage information. • Reads configuration options from the Command Line Interface (CLI) parameters. • Enumerates RAID controllers, physical disks, and virtual disks. • Creates and deletes virtual disks. • Logs activity to a given filename.
RAIDCFG Options And Arguments Table below lists all of the valid options, parameters, and arguments for the RAIDCFG utility. For more information on valid RAIDCFG options and their specific uses, see RAID Configuration Utility Options and Arguments. Mandatory command line options must be present in the command. Optional command line options can be typed in any order after the mandatory options have been typed. Many options have both a short and long format.
Option Valid Arguments Short Description Mandatory or Optional crbd Cancels the rebuild of the physical disk associated with a specified virtual disk. See Configuring Physical Disk Rebuild for specific information. Configures the array disk as RAID. See Configuring Array Disk as RAID for specific information. Creates encryption key for the encryption-capable controller. See Creating Encryption Key for specific information. Configures the array disk as JBOD.
Option Valid Arguments Short Description Mandatory or Optional dsk Deletes the encryption key of the encryption-capable controller. See Deleting Encryption Key for specific usage information. Configures the auto import property of the controller. See Configuring Auto Import for specific usage information. Enables the controller Persistent Hot Spare feature for the selected controller. See Enabling and Disabling Persistent Dedicated Hot Spares for specific usage information.
Option Valid Arguments Short Description Mandatory or Optional or Express (PCIe) link speed of the controller. Link Speed for specific usage information. Erases the encrypted physical disk that is in ready or foreign disk state. See Erasing Encrypted Physical Disk for specific usage information. Imports the foreign configuration of the virtual disks secured with the specified passphrase. See Importing Secured Foreign Configurations for specific usage information.
Option Valid Arguments Short Description Mandatory or Optional sbf Sets the indicated virtual disk as boot VD on the indicated controller. See Setting A Virtual Disk As Bootable Virtual Disk for specific usage information. Sets the bootmode of the controller to 0 (BIOS stop on error), 1 (BIOS continue on error), or 2 (Headless continue on error) during system startup or reboot. See Setting Boot Mode for specific usage information.
Option Valid Arguments Short Description Mandatory or Optional -c or controlleri d Specifies a RAID controller. See Enumerating RAID Controllers for specific usage information. -cp or cachepolicy d or e Specifies the cache policy for reads on a specified virtual disk or disk cache policy. Optional. -ctrl or controller NA Displays a list of the supported RAID controllers in the system, along with select property information.
Option Valid Arguments -l or logfile -o -r or raid Short Description Mandatory or Optional configurations on the specified controllers. See Miscellaneous Options for specific usage information. Logs command line output to a file. Optional. Reads the RAID configurations from all available controllers and write these configurations in the given .ini filename. Mandatory. Sets the RAID level for the array. Optional.
Option Valid Arguments Short Description Mandatory or Optional See Creating Virtual NOTE: Spanlength is Disks for specific applicable for RAID 10, usage information. RAID 50, and RAID 60. The minimum permissible spanlength value is 2for RAID 10, 3for RAID 50 and 4for RAID 60. The number of array disks for creating virtual disks should not be a prime number and should be divisible by the specified spanlength.
Option Valid Arguments Short Description Mandatory or Optional through caching), wc (writecaching), nwc (no-writecaching), and fwb (force-writeback). See Miscellaneous Options for specific usage information. RAID Configuration Utility Options And Arguments The following tables document valid options, parameters, and arguments along with a description of the expected behavior of each option.
• Increasing Virtual Disk Size • Discarding Preserved Cache • Displaying Foreign Key Ids • Creating Encryption Key • Changing Encryption Key • Deleting Encryption Key • Importing Secured Foreign Configurations • Creating Virtual Disks General Help The following table lists the RAIDCFG general help options. Table 13. General Help Option Parameters Valid Arguments Description No option-h NA NA or Displays general usage information for the utility.
Table 14. Enumerating RAID Controllers Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ctrl or controller NA NA Lists all the RAID controllers on the host system, along with select property information. This option is mandatory Example: raidcfg -ctrl Controller_ID/Slot_ID: 4 Controller_PCI_ID: 9:0:0 Controller_Name: PERC H710P Adapter Channels: 2 No.
NOTE: If you create a virtual disk on Windows PE, reboot the system. Table 15. Creating Virtual Disks Mandatory Options and Arguments Optional Parameters -ctrl -ac=cvd - NA c=id -ad= ch:targ,ch:tar g, Valid Parameters Arguments Description NA Creates a virtual disk comprising the properties supplied. This option combination is mandatory. NOTE: Create a bootable virtual disk only from the disk drives of slot 0-3 of the system. ... [or ch:targ:encl,. ..
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description NOTE: From DTK 2.4 onwards, the -fd option creates dedicated hot spares instead of global hot spares. For information about setting global hot spares, see Assigning, Unassigning, And Listing Global Hot Spares. For SCSI controllers, the value of LUN should always be 0. For SAS controllers, the value of enclosure can be non-zero, in which case you must specify values for channel, target, and enclosure.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description • -ctrl -ac=cvd - -rp or c=id -ad= readpolicy ch:targ,ch:tar g, ... [or ch:targ:encl,. ..] or controller action= createvdisk controllerid= id adisk= channel:target : lun, channel:target : lun,... ra, ara, nra, rc, nrc CAUTION: If the controller is changed from SCSI to RAID mode, expect data loss to occur. Back up any data you want to save before changing the modes.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description NOTE: The ra, ara, and nra options are supported on the following RAID controllers only: • • • • -ctrl -ac=cvd - -sp or c=id -ad= spanlength ch:targ,ch:tar g, ... [or ch:targ:encl,. ..] PERC 5/E Adapter, PERC 5/I Integrated, PERC 5/i Adapter PERC 6/i Integrated, PERC 6/i Adapter, PERC 6/E Adapter rc — (Read-Caching) Enables read caching. nrc — (No-Read-Caching) Disables read caching.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments disk space used on each array disk included in the stripe. A valid argument is a number that is less than the size of the virtual disk. The -sszoption is optional and can be added to the command line in any order after the mandatory option combination. However, do not specify a unit for stripe size when creating virtual disks. The unit is always displayed in KB. ch:targ,ch:tar g, ... [or ch:targ:encl,. ..
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments createvdisk controllerid= id adisk= channel:target : lun,... channel:target : lun,... [or channel:target : enclosure,...
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -wp or writepolicy wb, wt, wc, nwc, fwb Sets the write policy for the virtual disk. The valid arguments are: : enclosure,...] • • wb — Write-Back caching sets the controller to send a write-request completion signal as soon as the data is in the controller cache but has not yet been written to disk.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -sf or secureflag 0, 1 Creates a secured virtual disk on controllers with encryption capability and encryption key. Example: A:>raidcfg -ctrl -ac=cvd -c=2 -ad=1:4,1:8 -sf=1 RAIDCFG Command successful! Enumerating Array Disks The following table lists the RAIDCFG options, parameters, and pre-defined arguments for enumerating array disks (hard-drives).
Mandatory Options and Arguments Optional Parameters Valid Parameters/ Arguments Description PowerState: Spun Up SMARTState: No Error DiskState: Ready Encryption Capable: No Secured: Not Applicable Sector Size: 512B T10 Protection Info Capable: No ****** Physical Drive ****** Vendor: DELL Model: ST500NM0011 Protocol: SATA Media: HDD NegSpeed: 3072 Mbps CapSpeed: 3072 Mbps Certified: YES Supported: YES Location: 0:4:1 Size: 476416 MB (465 GB) Avail: 0 MB PowerState: Spun Up SMARTState: No Error DiskState:
Mandatory Options and Arguments Optional Parameters Valid Parameters/ Arguments Description Example: A:>raidcfg -ad -c=4 -vd=0 Controller: PERC H710P Adapter ****** Physical Drive ******Drive Vendor: DELL (tm) Model: ST3450757SS Protocol: SAS Media: HDD MedSpeed: 6144 Mbps CapSpeed: 6144 Mbps Certified: YES Supported: YES Location: 0:0:1 Size: 428672 MB (418 GB) Avail: 0 MB PowerState: Spun Up SMARTState: No Error DiskState: Online Encryption Capable: Yes Secured: No Sector Size: 512B T10 Protection Inf
Blinking And Unblinking Array Disks The following table lists the RAIDCFG options, parameters, and pre-defined arguments for blinking and unblinking array disks (hard drives). NOTE: You can also use pdisk or -pd instead of adisk or -ad to specify an array disk. Table 17. Blinking And Unblinking Array Disks Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ad -ad= ch:targ,ch:tar g ,... ac=blink c=id or adisk adisk= channel:target , channel:target ,...
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description Example: A:>raidcfg -vd Controller: PERC H710P Adapter VDisk ID: 0 Virtual Disk Name: Virtual Disk 0 Size: 857344 MB (837 GB) Type: RAID 0 Read Policy: Adaptive Read Ahead Write Policy: Write Back Cache Policy: Disabled Stripe Size: 64 Drives: 0:0:1,0:1:1 BootVD: No T10 Protection Info: Disabled RAIDCFG Command successful! -vd or vdisk -c or controller id Lists all the virtual disks
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description Example: A:>raidcfg -vd -c=2 -vd=0 Controller: PERC H710P Adapter VDisk ID: 0 virtual Disk Name: Virtual Disk 0 Size: 857344 MB (837 GB) Type: RAID 0 Read Policy: Adaptive Read Ahead Write Policy: Write Back Cache Policy: Disabled Stripe Size: 64 Drives: 0:0:1,0:1:1 BootVD: No T10 Protection Info: Disabled RAIDCFG Command successful! Deleting Virtual Disks The following table lists the RAIDCFG options, parameters
NOTE: When virtual disks are created, the RAID controller starts the background initialization operation. Virtual disks cannot be deleted until this operation completes. NOTE: If the raid.ini file contains the [Reset] section, then the RAIDCFG utility removes all the hot spares (dedicated and global) and virtual disks on the specified RAID controllers in the system.
Table 22. Blinking And Unblinking Virtual Disks Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -vd -vd=id ac=blink -c=id or vdisk vdisk=id action=blink controllerid=i d NA NA Blinks the physical disks associated with the specified virtual disk on the specified controller.
Table 23. Setting Environment Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -se envn= NA NA -envc= Sets a user-defined environment variable to the value returned from the getcontrollerslots function call. This option combination is mandatory.
Function Call Description Example: A:>raidcfg -se -envn=FIRMWARE -envc= getfirmware -c=2 FIRMWARE=531T RAIDCFG Command successful! getcontrollertype Returns LSI for LSI controllers and ADAP for Adaptec controllers. Example: A:>raidcfg -se -envn=CONTROLLERTYPE -envc= getcontrollertype -c=2 CONTROLLERTYPE=LSI RAIDCFG Command successful! getadisks Returns the array disks attached to the controller.
Function Call Description Example: A:>raidcfg -se -envn=HOTSPARES -envc= gethotspares -c=2 HOTSPARES=1:8:1,1:9:1 RAIDCFG Command successful! Returns the free array disks. getfreeadisks A:>raidcfg -se -envn=GETFREEADISKS -envc= getfreeadisks -c=2 GETFREEADISKS=0:3:1,0:4:1 RAIDCFG Command successful! Returns the total number of array disks.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description [vdisk0] controllerid=0 size=123456 raid=5 readpolicy=ra writepolicy=wt stripesize=32 cachepolicy=d adisk=0:0:1,0:1:1,0:2:1 [vdisk1] controllerid=0 size=65345 raid=1 readpolicy=ra writepolicy=wt stripesize=64 cachepolicy=d adisk=0:3:1,0:4:1 NOTE: If the controller uses global hot spares, the raid.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description Example: A:>raidcfg -ctrl -ac=sghs -c=2 -ad=0:1 -force RAIDCFG Command successful! -ad|-pd ac=lghs -c=id or adisk|pdisk action=listglo balhotspare controllerid=i d NA -ctrl —ac=rghs -c=id -ad|-pd= ch:targ:encl or controller action=removeg lobalhotspare controllerid=i d adisk| pdisk=channel: target:enclosu re NA NA Displays the array (physical) disks used for global hot spare for the specified controller.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description NOTE: For importing secured foreign configuration, use importsecureforeignconfig or isfc. For more details, see Importing Secured Foreign Configurations. Example: A:>raidcfg -ctrl -c=2 ac=fgnimp -ctrl -c=id ac= fgnclr NA NA or Clears the foreign configuration detected in the selected controller. This feature is supported on PERC 5 and later controllers and is not supported on SAS controllers..
Importing Secured Foreign Configuration The following table lists the RAIDCFG options, parameters, and pre-defined arguments for importing secured foreign configuration of the virtual disks. Table 28. RAIDCFG Options for Importing Secured Foreign Configuration Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ctrl -c=id ac=isfc pp=passphrase NA NA Imports the foreign configuration of the virtual disks secured with the specified passphrase.
Table 30. Creating Encryption Key Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ctrl -c=id ac=csk pp=passphrase -kid=key NA NA Creates encryption key for the encryption-capable controller.
Table 32. Deleting Encryption Key Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ctrl -c=id ac=dsk NA NA Deletes the encryption key of the encryption-capable controller.
Configuring Array Disk As RAID The following table lists the RAIDCFG options, parameters, and pre-defined arguments for configuring the array disk as RAID. Table 34. Configuring Array Disk as RAID Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ad -ac=ctr ad|-pd= ch:targ:encl c=id NA NA Configures the array disk as RAID.
Table 35. Configuring Physical Disk State Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ad -ac=online -ad|-pd= ch:targ:encl c=id NA NA Sets the array disk state to online. Example: A:>raidcfg -ad -ac=online ad=0:1 -c=2 or adisk action=online adisk| pdisk=channel: target:enclosu re controllerid=i d -ad ac=offline ad|-pd= ch:targ:encl c=id NA NA Cancels the rebuild of the physical disk associated with a specified virtual disk.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description pdisk adisk| pdisk=channel: target:enclosu re controllerid=i d Consistency Check For Virtual Disk The following table lists the RAIDCFG options, parameters, and pre-defined arguments for a consistency check for a virtual disk. Table 37.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description Example: ac=insecerase - c=id A:>raidcfg -ad -ad=0:1,0:2 -ac=insecerase -c=2 or adisk adisk | pdisk= channel:target :enclosure , channel:target :enclosure ,.. . action=instant secureerase controllerid= id Discarding Preserved Cache The following table lists the RAIDCFG options, parameters, and pre-defined arguments for discarding the preserved cache on the controller. Table 39.
Initializing Virtual Disks The following table lists the RAIDCFG options, parameters, and pre-defined arguments for initializing selected virtual disks. Table 40. Initializing Virtual Disks Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -vd -c=id vd=id -ac=fi or vdisk controllerid=i d vdisk=id action=fastini t NA NA Initializes the selected virtual disk in the selected controller with the fastinit command.
Table 41. Resetting The Controller Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description -ctrl -c=id ac=rst or controller controllerid=i d action=reset NA NA Resets the specified controller. Example: A:>raidcfg -ctrl -c=2 -ac=rst Enabling And Disabling Persistent Dedicated Hot Spares The following table lists the RAIDCFG options, parameters, and pre-defined arguments for enabling and disabling dedicated hot spares. Table 42.
Table 43. Setting and Displaying the PCIe Link Speed Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description --ctrl -c=id ac=spciels spd=<2 | 3> NA NA Sets the PCIe link speed of the controller to PCIe Generation 2 or 3. NOTE: Reboot the system to apply the setting.
Table 45.
Mandatory Options and Arguments Optional Parameters Valid Parameters Arguments Description the command line in any order after the mandatory options have been added. Example: A:>raidcfg -ctrl -l=log.txt Controller_ID/Slot_ID: Controller_PCI_ID: Controller_Name: PERC 6/E Channels: Virtual_Disks: Firmware Version: V2.8-0[6064] 0 4:2:1 Dell 2 0 RAIDCFG Command successful! -si or silent Does not display any information on the terminal console.
Purpose Command Description Example: A:>raidcfg -ctrl -ac=sghs -c=2 -ad=0:1 RAIDCFG Command successful! To list all the disks attached to a particular controller raidcfg adisk c=slotid To create a virtual disk with all the default settings raidcfg -ctrl ac=cvd -c=slotid ad= x:y,x:y,... To create a virtual disk of a certain size with all the default settings raidcfg -ctrl ac=cvd -c=slotid ad= x:y,x:y,...
Purpose Command Description commands. The drive location is obtained from the second command. To create a virtual disk of RAID 50 To create a virtual disk of RAID 6 raidcfg -ctrl ac=cvd -c=slotid ad= x:y,x:y,x:y,x:y ,x :y,x:y -r=50 -sp=x Creates a virtual disk of maximum size for type RAID 50. raidcfg -ctrl ac=cvd -c=slotid ad= x:y,x:y,x:y,x:y ,x :y,x:y -r=6 -sp=x Creates a virtual disk of maximum size for type RAID 6. The slot ID in <-c=slotid> and the array disks in <-ad=...
UPINIT 6 The UPINIT utility allows to create a utility partition (UP) on a hard drive, format the partition, and extract the partition contents onto the disk. Features The UPINIT utility: • Displays help and usage information. • Returns specific error codes and messages. NOTE: In Microsoft Windows Preinstallation Environment (Windows PE), you can find the UPINIT utility in \DELL\TOOLKIT\TEMPLATES\SCRIPTS.
On systems running Windows, UPINIT looks for the following files: • createup.cfg , mountup.cfg , umountup.cfg , and listup.cfg in the DELL\TOOLKIT\TEMPLATE\SCRIPTS directory • sysdrmk.exe in the DELL\TOOLKIT\TOOLS directory UPINIT Options And Arguments Table below lists the valid options and arguments for the UPINIT utility. Table 48. UPINIT Options and Arguments Option Valid Arguments Description none none If no options are given, the tool outputs usage information.
Option Valid Arguments Description Copyright (c) 2002-2012 Dell Inc. This utility creates a utility partition for your system. This utility requires a Utility Partition image file (upimg.bin) which can be found under /opt/dell/toolkit/systems folder in the Deployment Toolkit ISO. For more information, please consult the Deployment Toolkit Documentation. Usage: upinit.bat [--overwrite] --disk=ID or -d=ID --size=size or -s=size --file=file or -f=file --help or -h prints usage.
Option Valid Arguments Description --size or -s Size in MB for the Dell Utility Partition. --file or -f filename of Dell Utility Partition Image File. --overwrite or -o Installs the Dell Utility partition over an existing one. Example: upinit --disk=/dev/sda --size=32 -file=upimg.bin In the example, upinit creates a Dell Utility Partition of size 32 MB on /dev/sda using the upimg.bin file. The --overwrite option should be used for upgrading/ downgrading purposes.
Option Valid Arguments Description Example: A:>upinit --disk=0 --size=32 --file= c:\upimage.bin --overwrite string, optional Overwrites an existing utility partition. It does not create a new partition or delete an existing partition.
Messages And Codes 7 This section documents the error messages and codes used in Dell OpenManage Deployment Toolkit (DTK). SYSCFG Error Codes And Messages The SYSCFG utility checks your commands for correct syntax and valid input. When you enter a command, a message is displayed stating the results of the command. Failure Messages The SYSCFG utility failure messages provide error codes to help diagnose why some commands do not succeed. The following table lists SYSCFG error codes and messages. Table 49.
Error Code Message 14 The community string may only contain printable ASCII characters. 15 Destination unavailable. Cannot deliver request to selected destination. 16 Cannot execute command. Insufficient privilege level. 17 Command illegal for specified sensor or record type. 18 Invalid commstring value. 19 Hardware subsystem error. Invalid data field in Request. 20 Invalid destination IP address. 21 The GUID is invalid. 22 Invalid gateway. 23 Invalid hostname. 24 Invalid IP address.
Error Code Message 40 Password test failed. 41 Requested data length invalid. 42 Requested data field length limit exceeded. 43 Requested Sensor, data, or record not present. 44 Request data truncated. 45 Command response could not be provided. 46 Command response could not be provided. BMC initialization or initialization agent in progress. 47 Command response could not be provided. Device in firmware update mode. 48 Command response could not be provided. SDR Repository in update mode.
Error Code Message 68 The BIOS version information is not available. 69 There is not enough free system memory to complete the BIOS update. 70 The BIOS update file version is a different version class (A00, X00) than the current system BIOS. Use the --force option to use this BIOS image. 71 The BIOS update file version is older than the current system bios. Use the --force option to use this BIOS image. 72 The BIOS update file version is identical to the current system bios.
Error Code Message 90 Getting external serial connector settings failed. 91 Setting external serial connector settings failed. 92 There was an error opening the file. 93 File does not have write permission. 94 The file contains invalid options. 95 The replication information does not match for this system. 96 There can only be one section in the input file. 97 Bad ini file, the section cannot be found. 98 The format of the bios image file is incorrect.
Error Code Message 117 The option is not available or cannot be configured through software. 118 There was an error setting the option. 119 The -n (--namefile) option can only be used with - -pci. 120 The password may only contain alphanumeric characters. 121 The BIOS passwords have been disabled via jumper. 122 The password length must be between 1 and 32. 123 This password is locked and can only be unlocked by the admin user. 124 There was an error setting the password.
Error Code Message 142 Cannot stat /etc/omreg.cfg file. Please ensure /etc/omreg.cfg file is present and is valid for your environment. You can copy this file from the DTK iso. 143 Getting nicselection settings failed. 144 HAPI Driver Load Error. 145 Filter action power reduction is only supported for the system power warn/fail filters. 146 TPM/TCM Clear settings requires setup password. 147 There is currently no TPM/TCM Clear request pending.
Error Code Message 165 Invalid configuration. Attempting to apply IPv6 configuration on a non supported platform. 166 Invalid IPv6 configuration. Attempt to set DNS server address manually while DNS address source is set to auto. 167 Invalid IPv6 configuration. Attempt to set IPv6 address manually while IPv6 address source is set to auto. 168 Invalid IPv6 configuration. Attempting to apply IPv6 configuration without loading IPv6 stack. 169 Invalid IPv4 configuration.
Error Code Message 188 Error in setting the vFlash option. 189 The set operation failed due to dependency. 190 The set operation failed because attribute is forced to a value. 191 Cannot disable this OrderedList’s entries. 192 The set operation failed because system is busy now . Try again later. 193 New value for the token not valid. 194 Token not found. 195 The set operation failed because System Services and/or CSIOR disabled.
Error Code Message 212 Unsupported file name extension.Supported file name extensions are .ini, .log, .bat, .ids, .lst, and .txt. Failures And Solutions The following table lists the common SYSCFG failures and their solution. Table 50. SYSCFG Failures and Solutions Failure Messages Solutions Generic failure. Indicates iDRAC is in bad state. Reboot iDRAC. New value not valid. Make sure the changed value is valid. Cannot disable this orderedList’s entries.
Error Code Message 6 Error: Partitions exists. Please clear all the partitions before running upinit.sh. 7 Error: DOS file(s) not found at the specified path. 8 Error: UP IMAGE not found at the specified location. 9 Error: format failed. 10 Error: Invalid size. Size should be a number between 32 and 2000. 11 Error: sysdrmk failed. 12 System Error. 13 Error: Invalid Argument: 14 Error: Unzip failed.
Failure Messages The RAIDCFG utility failure messages provide error codes to help diagnose why some commands do not succeed. See table below for a list of the error codes and the associated messages. Table 54. RAIDCFG Error Codes and Messages Error Code Message 0 RAIDCFG Command successful! 1 Error! Incorrect Syntax. 2 Failure! 3 Illegal operation 4 Unsupported operation 5 Device not found. 6 Format boot drive illegal 7 Buffer too small. 8 Virtual Disk contains boot partition.
Error Code Message 24 RAID 5 not supported. 25 RAID 50 not supported. 26 Size too small for given RAID type. 27 Wrong number of disks for RAID 1- concatenated. 28 Insufficient space to mirror disks. 29 Create Mirror not supported. 30 Disk in use. 31 Disk Lock operation failed. 32 Disk locked. 33 Disk Unlock operation failed. 34 Disk Unlocked. 35 Disk failed on rebuild. 36 Hot Spare not free. 37 Disk Diagnostic failed. 38 Disk Rebuild failed. 39 Disk Format failed.
Error Code Message 55 Virtual disk locked. 56 Drive in use. 57 Reached maximum physical size. 58 Reached maximum count of virtual disks. 59 There is not enough free space on the array disk(s) to allow the operation to complete; the size of the virtual disk is too large; or communication to the array disk(s) has been lost. 60 Select the array disks that are part of a similar type of virtual disk (T10 protection and encryption capability) or the array disks that are not part of any virtual disks.
Error Code Message 81 Cancel resynchronization on virtual disk failed. 82 The maximum number of virtual disks that can be created has been reached. 83 The new virtual disk must use only the remaining free space on the array disks used in the last virtual disk you created. Select all array disks that are used in the last virtual disk you created. 84 You have selected an array disk that is in a degraded or failed state. Choose another array disk. 85 Delete the last created virtual disk first.
Error Code Message 106 SMART report count not supported. 107 Operations on hidden virtual disks are not allowed. 108 Virtual disk is in use. 109 The virtual disk is in use. It cannot be reconfigured at this time. 110 Virtual disk operation is temporarily unavailable. Initialization in progress. 111 Virtual disk operation is temporarily unavailable. Reconstruction in progress. 112 Virtual disk operation is temporarily unavailable. Rebuild in progress.
Error Code Message 132 Invalid controller state. 133 Controller failed. 134 Controller busy. 135 Controller does not exist. 136 Controller name is invalid. 137 Controller is iterated. 138 Rename of virtual disk was not successful. 139 The controller was not able to erase the file system from the specified virtual disk. 140 The controller was not able to add space to the specified concatenation set. 141 The controller was not able to get the status of the specified mirror set.
Error Code Message 160 Cannot communicate with controller. 161 Set operation failed. 162 Operation to update error count of SMART device has failed. 163 Operation to clear error count of SMART device has failed. 164 Driver could not execute. 165 Cannot delete virtual disk. 166 Cannot set temperature probe. Invalid value entered. 167 Cannot set enclosure tag. Invalid value entered. 168 Cannot set enclosure alarm. 169 Temperature probe value out of range. 170 Cannot set cache mode.
Error Code Message 181 The operation failed. Please rescan the controller and retry the operation. 182 The operation cannot be performed while a task is running on the specified virtual disk. 183 The specified virtual disk has no dead disk segments. 184 The operation cannot be performed at this time. The firmware can recondition a battery that has a Degraded or Power Low state. The firmware will not recondition a battery that is functioning normally or that has a Ready, Failed or Missing state.
Error Code Message 207 Invalid Strict option! Please provide a valid number between 1 and 100. 208 Span depth is not needed for this RAID type. 209 Array disk(s) cannot be part of virtual disk(s) and also be hotspares. 210 Cannot have silent and logfile switch with the same command. 211 Invalid array disk(s)! 212 Invalid failover disk(s)! 213 Creation of a virtual disk on this RAID controller requires the use of the entire disk space of the array disks.
Error Code Message 225 SAS 5/IR, SAS 6/IR, H200 and SW RAID requires atleast two physical disks to create RAID 0 or RAID 1. 226 No Foreign configuration present in the controller. 227 The virtual disk cannot be created on the physical disks you selected. Possible reasons include:unsupported mix of SAS and SATA protocol type disks, unsupported mix of SSD and HDD media disks. 228 Unsupported array disks selected for VD creation. 229 Setting stripe size is not supported in this controller.
Error Code Message ready state, and the size of the destination disk is greater than or equal to the size of the source disk. 1003 Operation not allowed. Cannot set the array disk state to online. 1004 Operation not allowed. Cannot set the array disk state to offline. 1005 Invalid encrypted array disk list for the instant secure erase operation. 1006 Sector drives 512B and 4KB must not be combined while creating a virtual disk. 1007 Hot spare sector size for the virtual disk is not matching.
Error Code Message 1023 Unsupported operation. Preserved cache is not present on the controller. 1024 Invalide Key Id 1025 Encryption key is already set for the controller. 1026 Cannot delete the encryption key because secure virtual disk is present. 1027 The passphrase is invalid or old. 1028 Cannot increase the virtual disk size due to lack of free space or due to the presence of partial virtual disks on the same set of array disks.
Error Code Message 9 LOGIN INCORRECT 10 NOT ACCESSIBLE VIA TELNET CONNECTION 11 ACCESS DENIED 12 INVALID ARGUMENT 13 INVALID GROUP NAME 14 USER DATABASE FULL 15 CAN'T CHANGE FACTORY DEFAULT 16 USER ALREADY IN DATABASE 17 CLOSING TELNET CONNECTION 18 USER DATABASE NOT INITIALIZED 19 INVALID COMMAND SHELL CALL 20 INVALID INPUT FILE 21 TFTP ERROR 22 PCI ERROR 23 SERVER IS IN GRAPHICS MODE 24 SYSTEM DATE AND TIME NOT SET 25 OUT OF MEMORY 26 ACCESS LOCKED 27 PAGING ERROR 2
Error Code Message 40 WRONG GRAPHICS MODE 41 CONFIG SPACE LOCKED 42 MASTER LOCKED 43 ASB BUS LOCKED 44 HISTORY MONITORS NOT YET AVAILABLE 45 NO VALID VALUE FOR THIS FIELD 46 DIAGNOSTIC TASK ERROR 47 DIAGNOSTIC TASK IS ALREADY RUNNING 48 NO DIAGNOSTIC TASK RUNNING 49 READ ONLY 50 SNARFING IS NOT AVAILABLE 51 TEXT RESOLUTION OF SERVER CHANGED 52 MODULE NOT LOADED 53 IPMI ERROR 54 ERROR IN DIAGNOSTIC FUNCTION RACADM Utility Error Codes And Messages Table below lists RACADM utili
Error Code Message 524 Invalid message type. 525 Invalid response message. 526 Specified user buffer is too small to hold data. 527 Authentication failed - Invalid user name or password. 528 Invalid CHAP protocol response encountered. 529 CHAP buffer too small. 530 Timeout occurred. 531 Insufficient user privileges to perform operation. 532 TFTP write error encountered. 533 TFTP read error encountered. 534 TFTP local file write error encountered.
Error Code Message 555 Failed to initialize FTP interface. 556 Failed to load SSL library. 557 Failed to initialize librac library. 558 Invalid session ID. 559 SpcmpObjectName failed. 560 SpcmpObjectIdGet failed. 561 SpcmpObjectIdSet failed. 562 Failed to send SPCMP message to RAC. 563 Invalid transport session info. 564 LAN Proxy error - please make sure your proxy settings are configured correctly. 565 RAC service not currently installed. 566 RAC service is not started.
BMC Platform Events Filter Alert Messages 8 All possible Platform Event Filter (PEF) Alert Messages along with a description of each event are listed in the table below Table 57. BMC PEF Alert Events Event Description Fan Probe Failure The fan is running too slow or not at all. Voltage Probe Failure The voltage is too low for proper operation. Discrete Voltage Probe Failure The voltage is too low for proper operation.
Event Description Hardware log is full or emptied Either an empty or a full hardware log requires administrator attention. Automatic System Recovery The system is hung or is not responding and is taking an action configured by Automatic System Recovery. System Power Probe Warning The system is setting actions when a power consumption probe detects a warning value. System Power Probe Failure The system is setting actions when a power consumption probe detects a failure value.
Sample File Formats 9 This appendix lists the sample SYSCFG utility .ini, RAIDCFG utility .ini, and the RACADM utility .ini files. Sample SYSCFG Utility .ini File Format [syscfg] ;SystemModelName=poweredge r620 ;SystemBiosVersion=0.3.16 ;SystemServiceTag=MDN2345 ;SystemManufacturer=dell inc. ;SysMfrContactInfo=www.dell.com ;SysMemSize=4.0 gb ;SysMemType=ecc ddr3 ;SysMemSpeed=1067 mhz ;SysMemVolt=1.
UsbPorts=allon InternalUsb=on IntegratedNetwork1=enable OsWatchdogTimer=disable IoatEngine=disable ;EmbVideo=enable SriovGlobalEnable=disable SerialComm=onnoconredir SerialPortAddress=serial1com1serial2com2 ExtSerialConnector=serial1 FailSafeBaud=115200 ConTermType=vt100vt220 RedirAfterBoot=enable SysProfile=perfperwattoptimizeddapc ;ProcPwrPerf=sysdbpm ;MemFrequency=maxperf ;ProcTurboMode=enable ;ProcC1E=enable ;ProcCStates=enable ;MemPatrolScrub=standard ;MemRefreshRate=1x ;MemVolt=autovolt ;AesNi=enable
destipaddr=0.0.0.0 commstring=public ;gateway=10.94.132.1 ;ipaddress=10.94.132.131 ipaddrsrc=dhcp nicselection=dedicated autoneg=enable dnsserver1=0.0.0.0 dnsserver2=0.0.0.0 dnsdhcp=disable dnsracname=idrac dnsregisterrac=disable domainname= domainnamednsdhcp=disable fullduplex=enable speed=100Mbps ;subnetmask=255.255.255.
usrprivlmt=noaccess lanuseraccess userid=11 usrprivlmt=noaccess lanuseraccess userid=12 usrprivlmt=noaccess lanuseraccess userid=13 usrprivlmt=noaccess lanuseraccess userid=14 usrprivlmt=noaccess lanuseraccess userid=15 usrprivlmt=noaccess lanuseraccess userid=16 usrprivlmt=noaccess lcd=servicetag nmibutton=enable pefcfgparams alertpolnum=1 alertpolstatus=disable pefcfgparams alertpolnum=2 alertpolstatus=disable pefcfgparams alertpolnum=3 alertpolstatus=disable pefcfgparams alertpolnum=4 alertpolstatus=disa
filter=procwarn filteralert=enable filteraction=none pefcfgparams filter=procfail filteralert=enable filteraction=none pefcfgparams filter=powerwarn filteralert=enable filteraction=none pefcfgparams filter=powerfail filteralert=enable filteraction=none pefcfgparams filter=hardwarelogfail filteralert=enable pefcfgparams filter=autorecovery filteralert=enable pefcfgparams filter=procabsent filteralert=enable filteraction=none pefcfgparams filter=powerabsent filteralert=enable filteraction=none pefcfgparams fi
filter=ripsoffline filteralert=enable filteraction=none pefcfgparams filter=ripsredundancylost filteralert=enable filteraction=none hostname= powerbutton=enable serialcfgparams connectionmode=basic msgcommbitrate=19200 msgcommflowctrl=noflowctrl tmcfgdelctrl=del tmcfgechoctrl=echo tmcfghandshakectrl=enable tmcfginputnewlineseq=cr tmcfglineediting=enable tmcfgnewlineseq=crlf serialchannelaccess ipmioverserial=alwaysavail channelprivlmt=administrator serialuseraccess userid=2 usrprivlmt=administrator serialus
userid=15 usrprivlmt=noaccess serialuseraccess userid=16 usrprivlmt=noaccess solaction userid=2 action=enable solaction userid=3 action=disable solaction userid=4 action=disable solaction userid=5 action=disable solaction userid=6 action=disable solaction userid=7 action=disable solaction userid=8 action=disable solaction userid=9 action=disable solaction userid=10 action=disable solaction userid=11 action=disable solaction userid=12 action=disable solaction userid=13 action=disable solaction userid=14 acti
userid=3 action=disable useraction userid=4 action=disable useraction userid=5 action=disable useraction userid=6 action=disable useraction userid=7 action=disable useraction userid=8 action=disable useraction userid=9 action=disable useraction userid=10 action=disable useraction userid=11 action=disable useraction userid=12 action=disable useraction userid=13 action=disable useraction userid=14 action=disable useraction userid=15 action=disable useraction userid=16 action=disable username userid=2 name=roo
username userid=9 name=NULL username userid=10 name=NULL username userid=11 name=NULL username userid=12 name=NULL username userid=13 name=NULL username userid=14 name=NULL username userid=15 name=NULL username userid=16 name=NULL ;uuid=44454C4C4400104E8032CDC04F333435 virtualmedia=auto Sample RAIDCFG Utility .
controllerid=4 size=278784 raid=5 readpolicy=ra writepolicy=wb stripesize=64 cachepolicy=c adisk=0:8:1,0:7:1,0:6:1 [GlobalHotspare0] controllerid=0 failoverdrive=0:8:0 Sample RACADM Utility .ini File Format [idRacInfo] #idRacType=0x05 #idRacProductInfo=Dell Remote Access Controller 5 #idRacDescriptionInfo=This system component provides a complete set of #remote management functions for Dell PowerEdge servers. #idRacVersionInfo=1.20 (Build 01.
cfgUserAdminEmailAddress= cfgUserAdminEmailCustomMsg= [cfgSessionManagement] cfgSsnMgtMaxSessions=0x4 cfgSsnMgtMaxSessionsPerUser=0x4 [cfgSerial] cfgSerialBaudRate=115200 cfgSerialConsoleEnable=0 cfgSerialConsoleQuitKey=~.
cfgADEnable=0 cfgADAuthTimeout=0x78 cfgADRootDomain= 252
