Dell™ OpenManage™ Server Administrator Version 6.1 Command Line Interface User's Guide w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. ____________________ Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . 15 What's New for Version 6.1 Using CLI Commands from Windows Command Prompts . . . . . . . . . Primary CLI Commands . . . . . . . . . . 17 . . . . . . . . . . . . . . . . . 17 . . . . . . . . 19 . . . . . . . . . . . . . . . . 19 . . . . . . . . . . . . . . . . . 19 . . . . . . . . . 20 . . . . . . . . . . . . . .
omreport about . . . . . . . . . . . . . . . . . . . . . omreport chassis/omreport mainsystem Commands . . . . . . . . . . . . . . . . . . . . . . . . 38 . . . . . 38 omreport chassis acswitch/omreport mainsystem acswitch . . . . . . . . . . . . . . . 38 omreport chassis batteries/omreport mainsystem batteries . . . . . . . . . . . . . . . . 39 . . . . . . . . . . 40 omreport chassis/ omreport mainsystem omreport chassis bios/omreport mainsystem bios . . . . . . . .
omreport chassis nics/omreport mainsystem nics . . . . . . . . . . . . . . . . . . 49 omreport chassis ports/omreport mainsystem ports . . . . . . . . . . . . . . . . . . 49 omreport chassis processors/omreport mainsystem processors . . . . . . . . . . . . . . omreport chassis pwrmanagement/omreport mainsystem pwrmanagement . . . . . . . . . . . 54 . . . . 55 . . . . . 57 omreport chassis pwrmonitoring/omreport mainsystem pwrmonitoring . . . . . . . .
omreport system recovery/omreport servermodule recovery . . . . . . . . . . . . . . . 68 omreport system shutdown/omreport servermodule shutdown . . . . . . . . . . . . . . 68 omreport system summary/omreport servermodule summary . . . . . . . . . . . . . . 68 omreport system thrmshutdown/omreport servermodule thrmshutdown . . . . . . . . . . . . 73 . . . . . . . . 74 . . . . . . . . . . . 75 omreport system version/omreport servermodule version . . . . . . . omreport preferences Commands .
omconfig chassis info/omconfig mainsystem info . . . . . . . . . . . . . . . . . . omconfig chassis leds/omconfig mainsystem leds . . . . . . . . . . . . . . . . . . omconfig chassis memorymode/omconfig mainsystem memorymode . . . . . . . . . . . . . omconfig chassis pwrmanagement/omconfig mainsystem pwrmanagement . . . . . . . . . 103 105 105 . . 107 omconfig chassis pwrmonitoring/omconfig mainsystem pwrmonitoring . . . . . . . . . . . .
omconfig system recovery/omconfig servermodule recovery . . . . . . . . . . . . . . . 142 omconfig system shutdown/omconfig servermodule shutdown . . . . . . . . . . . . . . 143 omconfig system thrmshutdown/omconfig servermodule thrmshutdown . . . . . . . . 5 omconfig system or servermodule assetinfo: Editing Cost of Ownership Values . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User Level Required for Adding Asset Information . . . . . . .
Adding Outsource Information . . . . . . . . . . . . . Example Command for Adding Outsource Information . . . . . . . . . . . . . . . . Adding Owner Information . . . . . 157 . . . . . . . . . . . . . . . 157 Example Command for Adding Owner Information . . . . . . . . . . . . . . Adding Service Contract Information . . . . . . . . 158 . . . . . . . . . 159 Example Command for Adding Service Information . . . . . . . . . . . . . . . Adding Support Information . . . . . . . 159 . . . . . . . .
omreport Storage Help . . . . . . . . . . . . . . . . . 169 . . . . . . . . . . . . . 170 omreport Controller Status omreport Global Information (Smart Thermal Shutdown Status, Hot Spare Protection Policy) . . . . . . . . . . . . . . . . . 170 . . . . . . . . . . . . . . 171 omreport Connector Status . . . . . . . . . . . . 171 omreport Enclosure Status . . . . . . . . . . . . . 172 omreport Battery Status omreport Temperature Probe Status . omreport Fan Status . . . . . . . 173 . . . .
. . . . . . . . 194 . . . . . . 195 . . . . . . . . . 195 omconfig Export the Controller Log omconfig Import Foreign Configuration omconfig Import/Recover Foreign Configuration . . . . . . . . . . . . . . . . . . 196 . . . . . . . . . . 196 omconfig Start Patrol Read . . . . . . . . . . . . 197 omconfig Stop Patrol Read . . . . . . . . . . . . 197 omconfig Clear Foreign Configuration omconfig Set Patrol Read Mode . . . . . . 198 . . . . . . . . . . . 199 omconfig Storage Controller .
omconfig Physical Disk Commands . omconfig Blink Physical Disk . . . . . . . . . . . 213 . . . . . . . . . . . 214 . . . . . . . . . . 215 . . . . 216 omconfig Unblink Physical Disk omconfig Prepare to Remove Physical Disk . . . . . . . . . . 217 omconfig Offline Physical Disk . . . . . . . . . . . 218 omconfig Offline Physical Disk . . . . . . . . . . . 218 omconfig Online Physical Disk . . . . . . . . . . . 219 omconfig Initialize Physical Disk omconfig Assign Global Hot Spare . .
omconfig Set All Temperature Probe Thresholds . . . . . . . . . . . . . . . . . . . . . omconfig Reset All Temperature Probe Thresholds . . . . . . . . . . . . . . . omconfig Blink 7 234 . . . . . . 235 . . . . . . . . . . . . . . . . . . . 235 Working With CLI Command Results . . . . . . . . . . . . . . . . . . . . . . . . . 237 Output Options for Command Results . . . . . . . 237 Controlling Command Output Display . . . . . . . 237 . . . . . . . . . 238 . . . . . . . . . .
Contents
Introduction You can perform essential systems management tasks using Dell™ OpenManage™ Server Administrator’s graphical user interface (GUI) or the command line interface (CLI). The reporting and viewing features allow retrieval of overall health status for systems on your network. At the component level, you can view information about voltages, temperatures, fan’s revolutions per minute (RPM), memory functioning, and many other critical component details.
• 16 • Reporting presence of optional iDRAC6 Enterprise card • Provides an option to configure reporting of more attributes on front panel LCD • Reporting presence of iDRAC6 Enterprise and the size of storage, if present • Reporting of new PCI devices that are part of xx1x systems • Display of the CPU turbo mode • Display of new memory types (DDR3 Registered, DDR3 Unregistered) • Display of new slot types (PCIe Gen1/2) • Enabling/disabling Non-Uniform Memory Architecture (Node Interleaving)
• Inclusion of Internet Protocol version 6: • This release supports IPv6, in addition to IPv4. NOTE: For the supported operating systems list, see the Dell Systems Software Support Matrix located at DVD_Drive\docs\readme\PEOSOM on the Dell-provided media or on the Dell support website at support.dell.com. NOTE: CLI commands are not supported on systems with VMware® ESXi operating system.
The omhelp command displays short text help for CLI commands. The shorthand equivalent of omhelp is the command for which you want help followed by -?. For example, to display help for the omreport command, type one of the following commands: omhelp omreport omreport -? The omreport command produces reports of your system’s management information. NOTE: For an overall summary of CLI commands, type omhelp. Table 1-1 lists the primary CLI commands used by Server Administrator.
CLI Error Checking and Error Messages When you type CLI commands, the CLI checks these commands for correct syntax. If you enter a command and the command is executed successfully, a message displays, stating that your command has been successful. Success Messages When you type a successful omconfig command, data for that component displays.
If you try to execute a command for a component or feature not present in your system configuration, the error message states that the component is not present. Command: omconfig chassis volts index=3 minwarnthresh= 3.3000 Example message: Error! Number with up to 3 digits after decimal point expected, read 3.3000 The value given by the command specifies more than 3 digits after the decimal point. A valid minimum warning threshold value for volts contains up to 3 digits after the decimal point.
a warning or failure event. In the most critical cases, the administrator could write a script so that the system shuts down to prevent damage. The administrator could then distribute and execute the script to many managed systems at the same time. Such a scenario facilitates configuring any number of new systems acquired by a company and makes implementation of new system administration policies easier across many existing systems that require reconfiguration.
The next level of complexity includes commands that contain command levels 1 and 2. All of the about commands are examples of command level 2 complexity. The omconfig about and omreport about commands cause a very brief summary to display. The summary shows version information for the systems management software installed on your system; for example, Server Administrator 1.x. Some commands have command level 1 and command level 2 and one name=value pair.
Using the omhelp Command The omhelp command and its equivalent, -?, accesses the CLI's detailed help text interface. You can get help at several levels of detail. Each fully qualified CLI command may have a variable number of distinct parts: the command (command level 1), one or more subcommands (command level 2 and command level 3, if present), and one or more name= value pair(s). By appending -? (space-dash-question mark) to any command, you can get help for that command.
• shutdown • thrmshutdown • webserver Figure 2-1 shows the levels of help for a command. Figure 2-1. Different Levels of Help for a Command You can also parse the omconfig system assetinfo command as follows: [name=value pair 2] where command levels 1, 2, and 3 are represented by omconfig system assetinfo, name=value pair 1 is represented by info=depreciation, and name=value pair 2 is represented by method=straightline.
For one info value, specify one or more optional parameter(s). Table 2-1 displays the optional parameters for info=acquisition: Table 2-1.
Using the omhelp Command
omreport: Viewing System Status Using the Instrumentation Service The omreport command allows you to see detailed information about your system components. You can retrieve summaries for many system components at one time, or you can get details about a specific component. This chapter shows you how to get reports with the level of detail that you want. Commands documented in this chapter vary in whether they define the fields that appear in the results of a particular omreport command.
Conventions for Parameter Tables When listing the parameters that a command can take, the parameters are listed in alphabetical order instead of the order in which they appear in the command line interface. The symbol |, often called pipe, is the logical exclusive or operator. For example, enable | disable means that you can enable or disable the component or feature, but you cannot simultaneously enable and disable the component or feature.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport Command Command Level 2 Level 1 Command Level 3 User Use Privilege Required omreport modularenclosure U, P, A Shows information for all the modular chassis. about U, P, A Shows version number and properties for Server Administrator. U, P, A Displays information for all the Server Administrator programs installed. U, P, A Shows the general status of all the main components.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport (continued) Command Command Level 2 Level 1 30 Command Level 3 User Use Privilege Required fans U, P, A Shows the status and thresholds for system fans. firmware U, P, A Shows firmware properties such as version, date of last update, and whether the firmware is updatable.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport (continued) Command Command Level 2 Level 1 Command Level 3 User Use Privilege Required leds U, P, A Shows the properties you have set for lightemitting diodes to flash under various alert conditions. memory U, P, A Shows properties of your system's memory arrays. nics U, P, A Shows the number of NICs installed in your system and displays controller and interface related details.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport (continued) Command Command Level 2 Level 1 Command Level 3 User Use Privilege Required pwrsupplies U, P, A Shows properties of power supplies. remoteaccess U, P, A Shows general information on remote access. slots U, P, A Shows properties of your system’s expansion slots and other slot types. temps U, P, A Shows the status and thresholds for the system temperature sensors.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport (continued) Command Command Level 2 Level 1 Command Level 3 User Use Privilege Required alertlog U, P, A Allows the administrator to display the alert log. assetinfo U, P, A Shows the cost of ownership information for your system. cmdlog U, P, A Allows the administrator to display the command log. esmlog U, P, A Allows the administrator to display the hardware log.
Table 3-2. Command Level 1, Level 2, and Level 3 for omreport (continued) Command Command Level 2 Level 1 preferences 34 Command Level 3 User Use Privilege Required recovery P, A Shows how your system is configured to respond to a hung operating system. shutdown P, A Shows how the shutdown action is to be performed. summary U, P, A Shows the key facts for all system components, including main system chassis, software, and storage.
Help With the omreport Command Use the omreport -? command to get a list of the available commands for omreport. Use omreport -? to get help on the level 2 about, chassis, and system commands. The following information on omreport system -? applies also applies to get help for the omreport chassis command.
Value : Chassis Management Controller (CMC) Attribute : Description Value : The system component provides a complete set of remote management functions for Dell systems. Attribute : Version Value : 1.0 (100) Attribute : IP Address Value : 101.102.103.
omreport about Use the omreport about command to learn the product name and version number of the systems management application installed on your system. The following is an example output from the omreport about command: Product name :Dell OpenManage Server Administrator Version :6.x.x Copyright :Copyright (C) Dell Inc. 1995-2009. All rights reserved. Company :Dell Inc.
omreport chassis/omreport mainsystem Commands Use the omreport chassis or omreport mainsystem commands to view details for the entire chassis or for a particular component. omreport chassis/ omreport mainsystem Type: omreport chassis or omreport mainsystem Server Administrator displays a general status for your main system chassis/main system components.
Server Administrator displays the following output: AC Failover Switch AC Switch Redundancy Redundancy Status Number of devices required for full redundancy Redundancy Mode Redundancy Configuration AC Power Lines Status Location AC Present Active Source Status Location AC Present Active Source : Full :2 : : Input Source Line 1, upon redundancy restoration, return to Line 1 : : : : : : : : Ok AC Power Line 1 Power Present Active Ok AC Power Line 2 Power Present Not Active Server Administrator reports val
omreport chassis bios/omreport mainsystem bios Use the omreport chassis bios/omreport mainsystem bios command to view the current BIOS information. Type: omreport chassis bios or omreport mainsystem bios Server Administrator displays the summary of the BIOS information for your system. omreport chassis biossetup/omreport mainsystem biossetup Use the omreport chassis biossetup or omreport mainsystem biossetup command to view BIOS setup parameters that are normally available only during system boot.
Table 3-3. BIOS Setup Parameters (continued) Parameters Description Processor CMP Displays the number of cores enabled per processor. User accessible USB Ports Displays whether the user-accessible USB port is enabled or disabled. CPU Virtualization Technology Displays the additional hardware capabilities provided by Virtualization Technology. AC Power Recovery Mode Displays the system state when input power is restored after an outage.
Table 3-3. BIOS Setup Parameters (continued) Parameters Description Bezel Displays whether the bezel removal intrusion check during system reboot is enabled or disabled. Console Redirection Displays if the BIOS screen is redirected over a particular serial port or if it is turned off. Diskette Displays whether the diskette is disabled, auto enabled, or read-only. Demand Based Power Management (DBS) Displays whether DBS is enabled or disabled on the system.
Table 3-3. BIOS Setup Parameters (continued) Parameters Description SATA Serial Port 1 Displays whether serial port 1 is mapped to a COM port, a COM port 1, a COM port 3, a COM1 BMC, a BMC Serial, a BMC NIC, a BMC RAC, or is disabled. Serial Port 2 Displays whether serial port 2 is mapped to a COM port, a COM port 2, a COM port 4, or is disabled. Speaker Displays whether the speaker is on or off. USB or USBB Displays whether the USB port is enabled or disabled.
omreport chassis fans/omreport mainsystem fans Use the omreport chassis fans or omreport mainsystem fans command to view the fan probe status and settings. Type: omreport chassis fans index=n or omreport mainsystem fans index=n The index parameter is optional. If you do not specify the index, Server Administrator displays a summary of status, readings, and thresholds set for any fan probes that might be present on your system.
omreport chassis frontpanel/omreport mainsystem frontpanel Use the omreport chassis frontpanel or omreport mainsystem frontpanel command to view if the front panel button control settings, such as the Power button and/or Nonmasking Interrupt (NMI) button (if present on the system), are enabled or disabled. If the Power button override is present on your system, you can see whether the Power button override is enabled or not. If enabled, the Power button turns the power to the system On and Off.
Depending on your configuration, output may resemble the following example: Hardware Performance Index : 0 Probe Name : System Board Power Optimized Status : Normal Cause : [N/A] omreport chassis info/omreport mainsystem info Use the omreport chassis info or omreport mainsystem info command to see a summary of installed component versions: omreport chassis info index=n or omreport mainsystem info index=n The index parameter specifies a chassis number and is optional.
Chassis Lock : Present Chassis Service Tag : 8RLNB1S Chassis Asset Tag : Flash chassis indentify LED state : Off Flash chassis indentify LED timeout value : 300 omreport chassis intrusion Use the omreport chassis intrusion command to find out whether the cover of your system is open or not. Server Administrator tracks chassis intrusion events because intrusions may indicate an attempt to steal a system component, or to perform unauthorized maintenance on the system.
The following is an example output: Flash chassis indentify LED state : Off Flash chassis indentify LED timeout : 300 value omreport chassis memory/omreport mainsystem memory Use omreport chassis memory or omreport mainsystem memory to view details for each memory module slot in your system. If your system supports redundant memory, this command also displays the status, state, and type of memory redundancy implemented on your system.
If your system supports redundant memory, the redundancy output may resemble the following: Memory Redundancy Redundancy Status Fail Over State Redundancy Configuration Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 Attributes Memory Array 1 : : : : : : : : : : : : : Full Inactive SpareBank Location Proprietary Add-on Card Use Unknown Installed Capacity 1536 MB Maximum Capacity 12288 MB Slots Available 12 omreport chassis nics/omreport mainsystem n
Port Type is the detailed type of each system port, from the more general serial, parallel, and USB ports to the names of ports by device type connected to it, for example, pointing device or keyboard. External Name is the name of the port, such as serial or parallel, USB, mouse, keyboard, and so on. Base I/O Address is the starting I/O address expressed in hexadecimal. IRQ Level is a hardware interrupt on a system.
External Clock Speed is the speed of the processor's external clock in MegaHertz. State refers to whether the processor slot is enabled or disabled. Core Count refers to the number of processors integrated into one chip. Capabilities and Cache Properties of a Specific Processor To view the cache properties of a processor on a given connector, type: omreport chassis processors index=n or omreport mainsystem processors index=n The index parameter is optional.
The following fields are defined for a cache present on a particular microprocessor. If the cache is internal to the processor, the fields do not appear in the cache report: • Speed • Cache Device Supported Type • Cache Device Current Type • External Socket Name NOTE: Due to the limitations of certain operating systems (for example, VMware® ESXi), certain features may not be available with this release of OpenManage Server Administrator.
A Write Policy describes how the cache deals with a write cycle. In a write-back policy, the cache acts like a buffer. When the processor starts a write cycle, the cache receives the data and stops the cycle. The cache then writes the data back to the main memory when the system bus is available. In a write-through policy, the processor writes through the cache to the main memory. The write cycle does not complete until the data is stored into the main memory.
omreport chassis pwrmanagement/omreport mainsystem pwrmanagement Use the omreport chassis pwrmanagement or omreport mainsystem pwrmanagement command to view the power budget cap and power management profiles of your system. Type: omreport chassis pwrmanagement or omreport mainsystem pwrmanagement For each power management profile in the system, values display for the following fields: Maximum Performance, Active Power Controller, OS Control, and Custom.
omreport chassis pwrmonitoring/omreport mainsystem pwrmonitoring Use the omreport chassis pwrmonitoring or omreport mainsystem pwrmonitoring command to view the properties of your system’s power consumption.
Power Consumption Information Power Consumption Index : 2 Status : Ok Probe Name : System Board Reading : System Level Warning Threshold : 539 W Failure Threshold : 994 W : 1400 W Power Headroom Name : System Instantaneous Headroom Reading : 300 W Name : System Peak Headroom Reading : 340 W Amperage 56 Location : PS 1 Current 1 Reading : 1.2 A Location : PS 2 Current 2 Reading : 1.
Power Tracking Statistics Statistics : Energy consumption Measurement Start Time : Thu Jun 28 11:03:20 2007 Measurement Finish Time : FRI Jun 28 11:05:46 2007 Reading : 5.9 KWH Statistics : System Peak Power Measurement Start Time : Mon Jun 18 16:03:20 2007 Peak Time : Wed Jun 27 00:23:46 2007 Peak Reading : 630 W Statistics : System Peak Amperage Measured Since : Mon Jun 18 16:03:20 2007 Read Time : Tue Jun 19 04:06:32 2007 Peak Reading : 2.
• Maximum Output Wattage • Online Status • Power Monitoring Capable omreport chassis remoteaccess/omreport mainsystem remoteaccess Use the omreport chassis remoteaccess or omreport mainsystem remoteaccess command to view general information on baseboard management controller or integrated Dell remote access controller (BMC/iDRAC) and remote access controller if DRAC is installed.
omreport chassis slots/omreport mainsystem slots Use the omreport chassis slots or omreport mainsystem slots command to view properties of your system’s slots. Type: omreport chassis slots index=n or omreport mainsystem slots index=n The index parameter is optional. If you do not specify the index, Server Administrator displays properties for all of the slots in your system. If you specify the index, Server Administrator displays properties for a specific slot.
omreport chassis volts/omreport mainsystem volts Use the omreport chassis volts or omreport mainsystem volts command to view properties of your system’s voltage probes. Type: omreport chassis volts index=n or omreport mainsystem volts index=n The index parameter is optional. If you do not specify the index, Server Administrator displays a summary of status, readings, and thresholds set for any voltage probes that might be present on your system.
SEVERITY : COMPONENT Ok : Main System Chassis Critical : Storage Commands for Viewing Logs You can use the omreport system or omreport servermodule command to view logs: the alert log, the command log, and the hardware or ESM log. NOTE: If the Alert log or Command log displays invalid XML data (such as when XML data generated for the selection is not well-formed), to clear the log and resolve the issue."omconfig system alertlog action=clear" or "omconfig system cmdlog action=clear" resolves the issue.
Overall Health Status of the ESM Log When you type omreport system esmlog or omreport servermodule esmlog, the ESM log displays. The first line of the report reflects the overall health of the system hardware. For example, Health: OK means that less than 80 percent of the space allotted for the ESM log is occupied by messages.
• Fan Warning • Fan Failure • Memory Pre-failure • Memory Failure • System Power Probe Warning • System Power Probe Detects a Failure • System Peak Power • Power Supply Warning • Power Supply Failure • Degraded Redundancy • Lost Redundancy • Temperature Warning • Temperature Failure • Voltage Warning • Voltage Failure • Processor Warning • Processor Failure • Hardware Log Warning • Hardware Log Full • Watchdog Asr • Storage System Warning • Storage System Failure
• Storage Controller Battery Warning • Storage Controller Battery Failure NOTE: Storage Controller Battery Warning and Storage Controller Battery Failure events are not available on modular systems. NOTE: System Power Probe Warning is not applicable to modular systems.
--------------Power Supplies ---------------Settings Enable: Informational, Warning and Critical Disable: None ----------Fans ----------Settings Enable: Critical Disable: Informational and Warning The full report lists the settings for all components in your system for which events can be generated. To view the status for components of a specific type, use the omreport system events type= or omreport servermodule event type= command.
Table 3-7. System Events by Component Type (continued) name=value pair Description type=systempower Reports events for system power. type=temps Reports events for temperatures. type=volts Reports events for voltages.
Type: omreport system pedestinations or omreport servermodule pedestinations The output of the omreport system pedestinations or omreport servermodule pedestinations command lists each of the valid parameters. NOTE: The actual number of destinations that can be configured on your system may differ. Table 3-8 shows the available settings. Table 3-8.
Table 3-8. Settings for the omreport system pedestinations/omreport servermodule pedestinations (continued) Output Attributes Description attribute= communitystring communitystring: Displays the text string that acts as a password and is used to authenticate SNMP messages sent between the BMC and the destination management station.
Example Command Output Type: omreport system summary or omreport servermodule summary The output that appears in your CLI window depends on the systems management software, operating system, and hardware components and options installed on your system.
Operating System Name : Microsoft Windows 2003 Server Version : Service Pack 2(Build 2XXX) System Time : Fri Sep 20 18:02:52 2XXX System Bootup Time : Wed Sep 18 18:37:58 2XXX Server Module -------------Information Host Name : svctag-dxxxxs System Location : Please set the value Model : PowerEdge 1955 Asset Tag : Test Service Tag : DXXXXS Slot Number : Slot 01-02 Form Factor : Half Height Dual Width Processor 1 Processor Brand : Intel(R) Xeon(R) CPU Processor Version : Model 15 Step
Memory Total Installed Capacity : 2048 MB Memory Available to the OS : 2048 MB Total Maximum Capacity : 32768 MB Memory Array Count : 1 The system summary hardware information includes data values for installed components of the following types present in your system: System Attributes • Host name • System location Main System Chassis/Main System Chassis • Chassis Model • Chassis Service Tag • Chassis Lock • Chassis Asset Tag Processor The following are listed for each processor in th
• Maximum Speed • External Clock Speed • Voltage Memory • Total Installed Capacity • Memory Available to the Operating System • Total Maximum Capacity • Memory Array Count Memory Array The following details are listed for each memory board or module in the system (for example, the system board or the memory module in a given slot number): • Location • Use • Installed Capacity • Maximum Capacity • Slots Available • Slots Used • Ecc Type BIOS 72 • Manufacturer • BIOS Version
Firmware • Name • Version Network Interface Card The following details are listed for each NIC in the system: • IP Address • Subnet Mask • Default Gateway • MAC Address Storage Enclosures The following details are listed for each storage enclosure attached to the system: • Name • Product ID omreport system thrmshutdown/omreport servermodule thrmshutdown Use the omreport system thrmshutdown or omreport servermodule thrmshutdown command to view the properties configured for a thermal shutdo
omreport system version/omreport servermodule version Use the omreport system version or omreport servermodule version command to list the version numbers of the BIOS, firmware, systems management software, and operating system installed on your system. Example Command Output Type: omreport system version or omreport servermodule version The output that appears in your CLI window depends on the version of the BIOS, RAID controllers, and firmware installed on your system.
--------------Software --------------Name : Microsoft Windows Server 2003, Enterprise Edition Version : 5.2 Name Version : Dell Server Administrator : 6.1 omreport preferences Commands Use the omreport preferences command to view the URL information of your Server Administrator Web server. Table 3-9 shows the available attributes. Table 3-9. omreport preferences webserver name=value pair Description attribute=geturl Reports the URL information of your Web server.
omreport: Viewing System Status Using the Instrumentation Service
omconfig: Managing Components Using the Instrumentation Service The omconfig command allows you to provide values that define warning events, configure alert actions, clear logs, and configure system shutdown, as well as allowing you to perform other systems management tasks.
Conventions for Parameter Tables When listing the parameters that a command can take, the parameters are listed in alphabetical order instead of the order in which they appear in the command line interface. The symbol |, often called pipe, is the logical exclusive or operator. For example, enable | disable means that you can enable or disable the component or feature, but you cannot simultaneously enable and disable the component or feature.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 User Privilege Required Use details=true U, P, A Displays information for all of the Server Administrator programs that are installed. cdvformat A Specifies the delimiter for separating data fields reported in custom delimited format (cdv). dirservice A Configures the Microsoft Active Directory® service. snmp A Sets the SNMP root password. Configures SNMP Set Operations.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 webserver User Privilege Required Use A Allows the administrator to set the encryption levels of the Web server and configure the URL launch point in the Server Administrator Web server environment.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 User Privilege Required Use cmdlog P, A Allows the administrator to clear the command log. esmlog P, A Allows the administrator to clear the ESM log. events P, A Enables and disables SNMP traps. pedestinations P, A Sets IP addresses for alert destinations. platformevents A Determines the shutdown action, if any, to be taken for a specific platform event.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 User Privilege Required Use thrmshutdown A Sets the severity level at which a thermal event triggers a system shutdown. webserver A Starts or stops the Web server. biossetup A Configures the behavior of specific system components controlled by the BIOS. bmc A Configures remote access information. chassis/ mainsystem NOTE: This command is phasedout in this release.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 User Privilege Required Use fancontrol P, A Allows you to optimize fan speed for maximum cooling or quiet operation. frontpanel A Configures the Power button and Nonmasking Interrupt (NMI) button if present on the system. info P, A Allows you to set an initial value, or to edit the value for, asset tag or chassis name.
Table 4-2. omconfig Command Level 1, Level 2, and Level 3 (continued) Command Level 1 Command Level 2 Command Level 3 User Privilege Required Use pwrmanagement P, A Allows you to choose between maximum power economy and optimized performance of the system. pwrmonitoring P, A Configures power consumption information and thresholds. remoteaccess A Configures remote access information. temps P, A Sets warning threshold values by default or value.
Help With the omconfig Command Use the omconfig -? command to get a list of the available commands for omconfig. Use omconfig -? to get help on the about, chassis, preferences, and system’s level 2 commands. The following information on omconfig system -? applies equally to getting help for the omconfig chassis command. Use the omconfig system -? command to get a list of the available commands for omconfig system.
To read the help for the alertaction command on a Microsoft® Windows®, Red Hat® Enterprise Linux®, or SUSE® Linux Enterprise Server operating system, type: more alert.txt omconfig about Use the omconfig about command to learn the product name and version number of the systems management application installed on your system. The following is an example output of the omconfig about command: Product name Version Copyright Company : Dell OpenManage Server Administrator : 6.x.x : Copyright (C) Dell Inc.
OpenManage Tools 6.x.x Remote Access Controller 4 Data Populator 4.x.x Remote Access Controller 4 Managed Node 4.6.3 Secure Port Server 1.x.x Server Administrator Framework 6.x.x Agent for Remote Access 1.x.x Storage Management 3.x.x Sun Java Runtime Environment 1.x.
Table 4-3 shows the name=value pairs you can use with this command. Table 4-3. BIOS Setup Settings name=value pair 1 name=value pair 2 attribute= setting= attribute= acpwrrecovery Description setting=off | last| on off: System is turned off. last: System returns to previous state. on: System is turned on. delay=random | random: System is turned on with immediate | timedelay random delay. time immediate: System returns to previous state immediately.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute=cstates enabled: Enables the processor to go into a deep sleep state when the system is not utilized. setting=enabled | disabled disabled: Disables the processor to go into a deep sleep state when the system is not utilized. attribute= conredirect setting=enabled | disabled enabled: Redirects the BIOS screen over Serial Port 1.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute= cpuxdsupport enabled: Enables Execute Disable (XD) support on system. setting=enabled | disabled disabled: Disables XD support on system. attribute=cpucore setting=1 | 2 | 4 | all 1: Enables one core per processor. 2: Enables two cores per processor. 4: Enables four cores per processor. all: Enables the maximum cores per processor.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute=dualnic setting=off | on | pxeboth | nic1pxe |nic2pxe | isciboth | nic1isci | nic2isci | nic1pxenic2isci | nic1iscinic2pxe | onpxeboth | onpxenone | off: Disables the Network Interface Controllers (NICs). on: Enables the network interface (PXE or iSCSI is not enabled on either of the NICs). pxeboth: Enables PXE on both NICs.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute= embvideoctrl enabled: Enables the embedded video controller to be the primary video device. setting=enabled | disabled disabled: Disables the embedded video controller to be the primary video device. attribute= extserial setting=com1 | com2 com1: Maps external serial connector to | rad COM 1. com2: Maps external serial connector to COM 2.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute= intrusion enabled: Enables the intrusion check during system boot. If the system also has bezel intrusion checking, then the intrusion option checks for removal of the bezel of the system. setting=enabled | disabled disabled: Disables the intrusion check during system boot. attribute=intusb attribute=mouse setting=enabled | disabled enabled: Enables the internal USB drive.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute=nic2 enabled: Enables the second NIC during system boot. setting=enabled | enabledwithpxe | disabled | enabledonly | enablednonepxe | enabledwithiscsi enabledwithpxe: Enables the second NIC during system boot (with PXE on if the system has PXE) disabled: Disables the second NIC during system boot.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute=nic4 enabled: Enables the fourth NIC during system boot. setting=enabled | enabledwithpxe | disabled | enabledonly | enablednonepxe | enabledwithiscsi enabledwithpxe: Enables the fourth NIC during system boot (with PXE on if the system has PXE) disabled: Disables the fourth NIC during system boot.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= attribute= ppmode Description setting=at | ps2 | ecp at: Sets the parallel port mode to | epp type AT. ps2: Sets the parallel port mode to type PS/2. ecp: Sets the parallel port mode to type ECP (extended capabilities port). epp: Sets the parallel port mode to type EPP (enhanced parallel port).
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute=rombb raid: Instructs the BIOS to detect RAID-on-motherboard channel B as a RAID device. setting=raid | scsi force=true scsi: Instructs the BIOS to detect this device as a SCSI device. force=true: Verification of setting change. attribute=sata setting=off | ata | raid off: Disables the SATA controller. ata: Sets the onboard SATA controller to ATA mode.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= Description attribute= serialport1 off: Disables serial port 1. setting=off | auto | com1 | com3 | bmcserial | bmcnic | rac | com1bmc auto: Maps serial port 1 to a COM port. com1: Maps serial port 1 to COM port 1. com3: Maps serial port 1 to COM port 3. bmcserial: Maps serial port 1 to BMC Serial. bmcnic: Maps serial port 1 to the Baseboard Management Controller (BMC) NIC.
Table 4-3. BIOS Setup Settings (continued) name=value pair 1 name=value pair 2 attribute= setting= attribute=uausb Description setting=on | backonly on: Enables the user-accessible | off USB port(s) backonly: Enables only the user accessible USB port(s) located at the back of the system. off: Disables the user-accessible USB port(s). attribute=usb setting=enabled | disabled enabled: Enables the USB port(s). disabled: Disables the USB port(s).
omconfig chassis bmc/omconfig mainsystem bmc NOTE: This command is phased-out in this release. It is replaced by the omconfig chassis remoteaccess/omconfig mainsystem remoteaccess command. omconfig chassis currents/omconfig mainsystem currents NOTE: This command is no longer available through Server Administrator. omconfig chassis fans/omconfig mainsystem fans Use the omconfig chassis fans or omconfig mainsystem fans command to set fan probe warning thresholds.
You cannot default one value and set another. In other words, if you default the minimum warning threshold value, you are also selecting the default value for the maximum warning threshold value. Specifying a Value for Minimum and Maximum Warning Thresholds If you prefer to specify values for the fan probe warning thresholds, you must specify the number of the probe you are configuring and the minimum and/or maximum warning threshold values.
omconfig chassis frontpanel/omconfig mainsystem frontpanel Use the omconfig chassis frontpanel or omconfig mainsystem frontpanel command to: • configure the power button and the Nonmasking Interrupt (NMI) button • configure the LCD to display: • no information • custom information • default system information • service tag, system name • MAC addresses of iDRAC6 • system power • IP address of iDRAC6 • ambient temperature of the system • IPv4 address of iDRAC6 • IPv6 address of iDRAC6 •
Table 4-6. omconfig chassis frontpanel/omconfig mainsystem frontpanel (continued) name=value pair 1 name=value pair 2 Description nmibutton= enable | disable NA enable: Enables the NMI button on the system. powerbutton= enable | disable config=sysname config=syspower config=servicetag config=ipv4idrac config=ipv6idrac config= ambienttemp security=modify security=view security=disabled remoteindication =true NA NA NA NA NA NA NA NA disable: Disables the NMI button on the system.
Table 4-7. omconfig chassis info/omconfig mainsystem info name=value pair Description index= Number of the chassis whose asset tag or name you are setting. Asset tag in the form of alphanumeric text. Letters or numbers should not exceed 10 characters. Name of the chassis.
omconfig chassis leds/omconfig mainsystem leds Use the omconfig chassis leds or omconfig mainsystem leds command to specify when to flash a chassis fault LED or chassis identification LED. This command also allows you to clear the LED for the system's hard drive. Table 4-8 shows the valid parameters for the command. Table 4-8.
Mirror mode switches to a redundant copy of memory when an uncorrectable memory event is detected. After switching to the mirrored memory, the system does not switch back to the original system memory until the next reboot. The operating system does not recognize half of the installed system memory in this mode. RAID mode provides an extra level of memory checking and error recovery at the expense of some memory capacity. Table 4-9 shows the valid parameters for the command. Table 4-9.
omconfig chassis pwrmanagement/omconfig mainsystem pwrmanagement Use the omconfig chassis pwrmanagement or omconfig mainsystem pwrmanagement command to configure power cap and manage profiles that control power utilization. Table 4-10. omconfig chassis pwrmanagement/omconfig mainsystem pwrmanagement name=value pair 1 name=value pair 2 Description config=budget cap= Sets the threshold value for power budget. enable: Enables powercap settings.
Table 4-10. omconfig chassis pwrmanagement/omconfig mainsystem pwrmanagement (continued) name=value pair 1 name=value pair 2 Description cpupowermode=min | min: Sets the CPU power max | systemdbpm | consumption to minimum. osdbpm max: Sets the CPU power consumption to maximum. systemdbpm: Sets the mode to system demand based power management. osdbpm: Sets the mode to operating system demand based power management. NOTE: These options are applicable only when custom profile is selected.
Table 4-11. omconfig chassis pwrmonitoring/omconfig mainsystem pwrmonitoring name=value pair 1 name=value pair 2 Description index= NA config=probe warnthresh= settodefault warnthresh= Number of the probe or probe index (must be specified). Sets minimum and maximum warning thresholds values to default. Sets a value for the warning threshold. watt: Displays the unit in Watts.
Specify a Value for Warning Thresholds If you prefer to specify values for the power consumption probe warning thresholds, you must specify the number of the probe you are configuring and the warning threshold value. You can configure the values to be displayed either in BTU/hr or Watts.
The output of the omconfig chassis remoteaccess or omconfig mainsystem remoteaccess command lists each of the available configurations. Table 4-12 shows the valid parameters: Table 4-12.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description altdnsserverv6 Validates the address of the alternate DNS server for configuration. dnssourcev6=static | auto static: DNS source is set to static. config=nic (continued) encryptkey=text confirmencryptkey=text gateway=Gateway gatewayv6= enablenic=true | false auto: DNS source is set to auto. text: Text used for encryption and confirmation of encryption.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description ipsource=static | dhcp | static: Static if the IP address of the systemsoftware BMC LAN interface is a fixed, assigned IP address. dhcp: DHCP if the source of the IP address of the BMC LAN interface is the dynamic host configuration protocol. systemsoftware: System software if the source of the IP address of the BMC LAN interface is from the system software.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description vlanid=number config=serial number: Virtual LAN identification in the range of 1 to 4094. vlanpriority=number number: Priority of virtual LAN identification in the range of 0 to 7. baudrate=9600 | 19200 | 9600: Sets the connection speed to 9600 38400 | 57600 | 115200 bits per second. 19200: Sets the connection speed to 19200 bits per second.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description config=serial (continued) directbasic: Type of messaging used for IPMI messaging over a serial connection. mode=directbasic | directterminal | directbasicterminal | modembasic | modemterminal | modembasicterminal directterminal: Type of messaging that uses printable ASCII characters and allows a limited number of text commands over a serial connection.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description baudrate=9600 | 19200 | 9600: Sets the volatile and nonvolatile 38400 | 57600 | 115200 connection speed to 9600 bits per second. 19200: Sets the volatile and non-volatile connection speed to 19200 bits per second. 38400: Sets the volatile and non-volatile connection speed to 38400 bits per second.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description privilegelevel= administrator: Sets the maximum administrator | operator | privilege level that can be accepted on a user serial over LAN channel, to Administrator. operator: Sets the maximum privilege level that can be accepted on a serial over LAN channel, to Operator.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description newlinesequence=none | none: BMC does not use a crlf | null | cr | lfcr | lf termination sequence. crlf: BMC uses as a new line sequence when the BMC writes a new line to the console. null: BMC uses as a new line sequence when the BMC writes a new line to the console.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= Description id=number newpw=text number: ID (in numeric format) of the user being configured. confirmnewpw=text newpw=text: New password of the user. confirmnewpw=text: Confirm the new password. id=number: ID (in numeric format) of the user being configured.
Table 4-12. omconfig chassis remoteaccess/omconfig mainsystem remoteaccess (continued) name=value pair 1 name=value pair 2 config= id=user id dracusergroup=admin | poweruser | guest | custom | none Description id=user id: User ID of the user being configured. dracusergroup=admin: Enables the Administrator user privileges. dracusergroup=poweruser: Enables the Power User privileges. dracusergroup=guest: Enables the Guest user privileges. dracusergroup=custom: Enables the Custom User privileges.
Table 4-13. omconfig chassis remoteaccess config=user id= dracusergroup=custom/omconfig mainsystem remoteaccess config=user id= dracusergroup=custom name=value pair 1 name=value pair 2 config=user (continued) name=value pair 3 id=user id logindrac= true | dracusergroup= false custom configuredrac= true | false Description true/false: Enables/disables logging into DRAC. true/false: Enables/disables configuration of DRAC.
omconfig chassis temps/omconfig mainsystem temps Use the omconfig chassis temps or omconfig mainsystem temps command to set warning thresholds for temperature probes. As with other components, you can view both warning and failure threshold values, but you cannot set failure threshold values. Your system's manufacturer sets the minimum and maximum failure threshold values. NOTE: Threshold values that you can set vary from one system configuration to another.
Setting Minimum and Maximum Warning Threshold Values If you want to set both the upper and lower temperature warning threshold values to the recommended default value, type: omconfig chassis temps index=0 warnthresh=default or omconfig mainsystem temps index=0 warnthresh= default You cannot default one value and set another. In other words, if you set the minimum warning threshold value to the default value, you are also selecting the default value for the maximum warning threshold value.
Valid Parameters for Voltage Warning Thresholds Table 4-16 shows the valid parameters for setting voltage warning threshold values. NOTE: Threshold values that you can set vary from one system configuration to another. Table 4-16. omconfig chassis volts/omconfig mainsystem volts name=value pair Description index= warnthresh=default Probe index (must be specified). Sets minimum and maximum warning threshold values to default. Sets minimum warning threshold value(3 decimal places).
Specify a Value for Minimum and Maximum Warning Thresholds If you want to specify values for the voltage probe warning thresholds, you must specify the number of the probe you are configuring and the minimum and/or maximum warning threshold values. In the following example, the probe being configured is probe 0: omconfig chassis volts index=0 minwarnthresh=1.900 maxwarnthresh=2.250 or omconfig mainsystem volts index=0 minwarnthresh= 1.900 maxwarnthresh=2.
omconfig preferences dirservice Use the omconfig preferences dirservice command to configure the Active Directory service. The oem.ini file is modified to reflect these changes. If the "adproductname" is not present in the oem.ini file then a - default value is used. refers to the name of the computer running Server Administrator and refers to the name of the product defined in omprv32.ini.
omconfig preferences snmp Setting the SNMP root password allows administrators to restrict access to SNMP set operations that allow important systems management interventions. You can configure the SNMP root password normally (by typing all of the parameters in one command line) or interactively. Using the omconfig preferences snmp command, you can also configure SNMP set operations.
When you type omconfig preferences snmp, you must supply all the parameters in the initial command line. For example: omconfig preferences snmp setting=rootpw oldpw= openmanage newpw=serveradmin confirmnewpw= serveradmin Table 4-19.
Table 4-20 shows the valid parameters for the command. Table 4-20. Enabling User Access for Administrators, Power Users, and Users Command Result Description omconfig preferences useraccess enable=user Grants Server Administrator access to Users, Power Users, and Administrators. Grants Server Administrator access to Power Users and Administrators. Grants Server Administrator access to Administrators only. Least restrictive form of user access.
The host input must contain a valid IPv4 or IPv6 address, or a valid hostname. For more information on configuring Web server preferences, see the Dell OpenManage IT Assistant User’s Guide. omconfig system/omconfig servermodule Use the omconfig system or omconfig servermodule commands to clear logs, determine how various shutdown actions occur, set initial values or edit values for cost of ownership information, and determine how to respond to a hung operating system.
Syntax for Setting Alert Actions Setting an alert action requires two name=value pairs. The first name=value pair is the event type. The second name=value pair is the action to take for this event. For example, in the command: omconfig system alertaction event=powersupply broadcast=true or omconfig servermodule alertaction event= powersupply broadcast=true The event is a power supply failure and the action is to broadcast a message to all Server Administrator users.
Components and Events for Which You Can Set Alert Actions Table 4-23 lists the components and the events for which you can set alert actions. Components are listed in alphabetical order, except that warning events always precede failure events for a component. Table 4-23.
Table 4-23. Events for Which You Can Set Alert Actions (continued) Event Name Description event=tempwarn Sets actions when a temperature probe detects a warning value. Sets actions when a temperature probe detects a failure value. Sets actions when a voltage probe detects a warning value. Sets actions when a voltage probe detects a failure value.
Example Current Probe Actions To disable system console alert if a current probe detects a warning event, type: omconfig system alertaction event=currentwarn alert=false or omconfig servermodule alertaction event= currentwarn alert=false To enable broadcast messages if a current probe detects a failure event, type: omconfig system alertaction event=currentfail broadcast=true or omconfig servermodule alertaction event= currentfail broadcast=true Example Fan Probe Actions To generate alerts when a fan probe
Commands for Clearing Logs NOTE: For more information about alert messages, see the Dell OpenManage Server Administrator Messages Reference Guide. You can use the omconfig system or omconfig servermodule command to clear three logs: the alert log, the command log, and the hardware or ESM log. To clear the contents of the alert log, type: omconfig system alertlog action=clear or omconfig servermodule alertlog action=clear NOTE: Entering an invalid RAC user name may prevent the command log from displaying.
Table 4-24. omconfig system pedestinations/omconfig servermodule pedestinations name=Value Pair Description destenable=true | false true: Enables an individual platform event filter destination after a valid IP address has been set. false: Disables an individual platform event filter. index=number Sets the index for the destination. ipaddress=ipv4|ipv6 Sets the IP address for the destination.
Table 4-25. Parameters for Alert Action Command (continued) Action Description action= powerreduction Reduces the processor speed until the power consumption comes down and reaches below the warning threshold. If the system power consumption stays below the warning threshold, increases the processor speed NOTE: This action is applicable only to non–modular systems.
Table 4-26. omconfig system platformevents (continued) Event Name Description event=powerwarn Sets action or enables/disables alert generation when a power device probe detects that the power supply, voltage regulator module, or DC to DC converter is pending a failure condition. event=powerabsent Sets action or enables/disables alert generation when a processor probe detects that the power supply is absent.
Table 4-26. omconfig system platformevents (continued) Event Name Description event=voltfail Sets action or enables/disables alert generation when a voltage probe detects that the voltage is too low for proper operation. event=watchdogasr Enables or disables alert generation configured by the ASR when the system has hung or is not responding.
Table 4-27. System Event Type Parameters name=value pair Description type=accords type=battery type=all type=fanenclosures type=fans type=intrusion type=log type=memory type=powersupplies type=redundancy type=systempower type=temps type=volts type=systempeakpower Configures events for AC power cords. Configures events for battery. Configures events for all device types. Configures events for fan enclosures. Configures events for fans. Configures events for chassis intrusion. Configures events for logs.
Table 4-28.
omconfig system webserver/omconfig servermodule webserver Use the omconfig system webserver or omconfig servermodule webserver command to start or stop the Web server. Table 4-29 shows the valid parameters for the command. Table 4-29. Web Server Configuration Parameters name=value pair action=start action=stop action=restart Description Starts the Web server. Stops the Web server. Restarts the Web server.
Example Recovery Commands To set the action on hung operating system detection to powercycle, type: omconfig system recovery action=powercycle or omconfig servermodule recovery action=powercycle To set the amount of time that the system must be hung before a recovery action is initiated to 120 seconds, type: omconfig system recovery timer=120 or omconfig servermodule recovery timer=120 omconfig system shutdown/omconfig servermodule shutdown Use the omconfig system shutdown or omconfig servermodule shutdow
Example Shutdown Commands To set the shutdown action to reboot, type: omconfig system shutdown action=reboot or omconfig servermodule shutdown action=reboot To bypass operating system shutdown before the system is powered off, type: omconfig system shutdown action=reboot osfirst= false or omconfig servermodule shutdown action=reboot osfirst=false omconfig system thrmshutdown/omconfig servermodule thrmshutdown Use the omconfig system thrmshutdown or omconfig servermodule thrmshutdown command to configure a
Example Thermal Shutdown Commands To trigger a thermal shutdown when a temperature probe detects a failure event, type: omconfig system thrmshutdown severity=failure or omconfig servermodule thrmshutdown severity= failure To disable thermal shutdown so that an administrator has to initiate an omconfig system shutdown, type: omconfig system thrmshutdown severity=disabled or omconfig servermodule thrmshutdown severity= disabled omconfig: Managing Components Using the Instrumentation Service 145
omconfig: Managing Components Using the Instrumentation Service
omconfig system or servermodule assetinfo: Editing Cost of Ownership Values Overview The omconfig system assetinfo or omconfig servermodule assetinfo command helps you to edit a comprehensive set of parameters that make up your system's total cost of ownership. This section explains the parameters that can be reported and configured under the omconfig system assetinfo or omconfig servermodule assetinfo command.
Adding Acquisition Information Acquisition refers to the facts about a business entity's purchase or lease of a system. Use the omconfig system assetinfo info=acquisition or omconfig servermodule assetinfo info=acquisition command to add detailed information about the purchase or lease of a system. Table 5-2 shows the valid parameters for the command. Table 5-2.
Table 5-2. omconfig system assetinfo info=acquisition/omconfig servermodule assetinfo info=acquisition (continued) Command Command Level 1 Level 2 Command Name= Name= Value Pair 2 Description Level 3 Value Pair 1 signauth= waybill= Name of the person who approved the purchase or the service call on the system. Receipt from the carrier for the goods received.
purchasecost=5000 waybill=123456 installdate=120501 purchasedate= 050601 ponum=9999 signauth="John Smith" expensed= yes costcenter=finance The following message appears: Asset information set successfully. Adding Depreciation Information Depreciation is a set of methods for computing the devaluation of your asset over time. For example, the depreciation of a system that is expected to have a useful life of 5 years would be 20 percent.
Example Commands for Adding Depreciation Information To provide a value for a depreciation parameter, type a command of the form: omconfig system assetinfo info=depreciation or omconfig servermodule assetinfo info=depreciation . For example, type: omconfig system assetinfo info=depreciation method=straightline or omconfig servermodule assetinfo info=depreciation method=straightline The following message appears: Asset information set successfully.
Table 5-4 shows the valid parameters for the command. Table 5-4. omconfig system assetinfo info=extwarranty/omconfig servermodule assetinfo info=extwarranty Command Level 1 Command Level 2 Command Level 3 Name= Value Name= Value Description Pair 1 Pair 2 omconfig system/server module assetinfo info= extwarranty cost= enddate= Cost of the extended warranty service. Date the extended warranty agreement ends.
You can enter more than one omconfig system assetinfo or omconfig servermodule assetinfo command at the same time, as long as all the parameters for name=value pair 2 belong to the same name=value pair 1. For an example, see "Example Commands for Adding Acquisition Information." Adding Lease Information A lease is an agreement to pay for the use of a system for a specified period of time. The lessor retains ownership of the system. Table 5-5 shows the valid parameters for the command. Table 5-5.
Example Command for Adding Lease Information To provide a value for a lease parameter, type a command of the form: omconfig system assetinfo info=lease or omconfig servermodule assetinfo info=lease . For example, type: omconfig system assetinfo info=lease value=4500 or omconfig servermodule assetinfo info=lease value= 4500 The following message appears: Asset information set successfully.
Table 5-6. omconfig system assetinfo info=maintenance/omconfig servermodule assetinfo info=maintenance (continued) Command Command Level 1 Level 2 Command Name= Value Level 3 Pair 1 Name= Value Pair 2 Description provider= Business entity providing the maintenance service. startdate= Date the maintenance begins. restrictions= Activities not covered by the maintenance contract.
Adding Outsource Information Outsourcing is the practice of contracting with another business to maintain the system in good working order. Table 5-7 shows the valid parameters for adding outsource information. Table 5-7.
Example Command for Adding Outsource Information To provide a value for an outsource parameter, type a command of the form: omconfig system assetinfo info=outsource or omconfig servermodule assetinfo info=outsource . For example, type: omconfig system assetinfo info=outsource providerfee=75 or omconfig servermodule assetinfo info=outsource providerfee=75 The following message appears: Asset information set successfully.
Table 5-8. omconfig system assetinfo info=owner/omconfig servermodule assetinfo info=owner (continued) Command Command Level 1 Level 2 Command Name= Value Name= Value Level 3 Pair 1 Pair 2 ownername = type=owned | leased | rented Description Business entity that owns the system. Whether the user of the system owns, leases, or rents the system.
Adding Service Contract Information A service contract is an agreement that specifies fees for preventive maintenance and repair of the system. Table 5-9 shows the valid parameters for adding contract information. Table 5-9.
You can enter more than one omconfig system assetinfo or omconfig servermodule assetinfo command at the same time, as long as all the parameters for name=value pair 2 belong to the same name=value pair 1. For an example, see "Example Commands for Adding Acquisition Information." Adding Support Information Support refers to technical assistance that the system user can seek when the user seeks guidance on the proper use of a system to perform tasks.
Table 5-10. omconfig system assetinfo info=support/omconfig servermodule assetinfo info=support (continued) Command Command Level 1 Level 2 Command Name= Name= Value Pair 2 Description Level 3 Value Pair 1 outsourced=true Whether an external | false business entity provides technical support or the system owner's employees provide technical support. type=network | Whether support is storage for network attached devices or for storage devices.
Adding System Information System information includes the primary user of the system, the phone number for the primary user, and the location of the system. Table 5-11 shows the valid parameters for adding system information. Table 5-11.
You can enter more than one omconfig system assetinfo or omconfig servermodule assetinfo command at the same time, as long as all the parameters for name=value pair 2 belong to the same name=value pair 1. For an example, see "Example Commands for Adding Acquisition Information." Adding Warranty Information Use the omconfig system warranty or omconfig servermodule warranty command to assign values for warranty information.
Example Command for Adding Warranty Information To provide a value for a warranty parameter, type a command of the form: omconfig system assetinfo info=warranty or omconfig servermodule assetinfo info=warranty . For example, type: omconfig system assetinfo info=warranty unit=days or omconfig servermodule assetinfo info=warranty unit=days The following message appears: Asset information set successfully.
Using the Storage Management Service The CLI of Storage Management enables you to perform all of Storage Management’s reporting, configuration, and management functions from an operating system command shell. The Storage Management CLI also enables you to script command sequences. The Storage Management CLI provides expanded options for the Dell™ OpenManage™ Server Administrator omreport and omconfig commands. This chapter only documents the omreport and omconfig commands that apply to Storage Management.
Table 6-1 describes these command levels. Table 6-1. Example Command Levels Command level 1 Command level 2 Command level 3 Use omconfig storage pdisk Specifies the command Indicates the Server Administrator service (in this case, Storage Management) that implements the command Specifies the type of object on which the command operates Following the command levels, the omreport and omconfig command syntax may require one or more name=value pairs.
Table 6-2. Syntax For Name=Value Pairs For Parameters Syntax Description controller=id Indicates the controller ID as reported by the omreport storage controller command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=id to display the IDs for the physical disks attached to the controller. connector=id vdisk=id For example, the controller=id parameter might be specified as controller=1.
Table 6-2. Syntax For Name=Value Pairs For Parameters (continued) Syntax Description battery=id Indicates the battery ID as reported by the omreport command. To obtain this value, enter omreport storage controller to display the controller IDs and then enter omreport storage battery controller=id to display the ID for the controller battery. The caret symbols (< >) enclose variable elements that you must specify.
omreport Storage Help Table 6-3 provides the omreport storage command syntax. Table 6-3. Command Level 1 omreport storage help Command Level 2 Command Level 3 Use omreport storage pdisk vdisk controller enclosure connector battery globalinfo Displays a list of storage components for which omreport commands are available. Displays a list of the omreport storage pdisk parameters for displaying physical disk information.
omreport Controller Status Table 6-4 describes the syntax for the omreport Controller Commands. Table 6-4. omreport Controller Commands Required Command Optional name= Levels (1, 2, 3) value pairs Use omreport storage controller Displays property information for all controllers attached to the system. Displays the specified controller and all attached components such as enclosures, virtual disks, physical disks, and so on. controller=id where id is the controller number.
omreport Battery Status Table 6-6 describes the syntax for the omreport Battery Commands. Table 6-6. omreport Battery Commands Required Command Levels (1, 2, 3) Optional name=value pairs Use omreport storage battery controller=id where id is the controller number. For example: controller=0 Displays all batteries present on all controllers on the system. (Some controllers do not have batteries). Displays the battery on the specified controller.
omreport Enclosure Status Table 6-8 describes the syntax for the omreport Enclosure Commands. Table 6-8. omreport Enclosure Commands Required Command Levels (1, 2, 3) Optional name=value pairs omreport storage enclosure controller=id enclosure= where id is the controller number and is the enclosure ID. Example for SCSI controllers: controller=0 enclosure=2. Example for SAS controllers: controller=0 enclosure= 1:2.
omreport Temperature Probe Status Table 6-9 describes the syntax for the omreport Probe Commands Table 6-9. omreport Temperature Probe Commands Required Command Levels Optional name=value pairs (1, 2, 3) and name=value pair Use omreport storage enclosure Displays property information for all enclosures attached to the system. controller=id enclosure= Displays the temperature probes for the specified info=temps enclosure.
omreport Fan Status Table 6-10 describes the syntax for the omreport Fan Commands Table 6-10. omreport Fan Status Required Command Levels Optional name=value pairs (1, 2, 3) and name=value pair omreport storage enclosure Use Displays property information for all enclosures attached to the system. controller=id enclosure= Displays the fans for the info= specified enclosure. fans where id is the controller number and ENCLOSUREID is the enclosure number.
omreport Power Supply Status Table 6-11 describes the syntax for the omreport Power Supply Commands Table 6-11. omreport Power Supply Commands Required Command Levels (1, Optional name=value pairs 2, 3) and name=value pair omreport storage enclosure Use Displays property information for all enclosures attached to the system. controller=id enclosure= Displays the power supplies for the specified enclosure.
omreport EMM Status NOTE: The status of the EMMs is displayed as degraded if there is a mismatch between the EMM firmware. Table 6-12 describes the syntax for the omreport EMM Commands Table 6-12. omreport EMM Commands Required Command Levels Optional name=value pairs Use (1, 2, 3) and name=value pair omreport storage enclosure Displays property information for all enclosures attached to the system.
omreport Physical Disk Status Table 6-13 describes the syntax for the omreport Physical Disk Commands Table 6-13. omreport Physical Disk Commands Required Command Levels (1, 2, 3) and name=value pair Optional name=value pairs omreport storage pdisk controller=id Use Displays all physical disks where id is the controller attached to the specified controller. number.
omreport Virtual Disk Status Table 6-14 describes the syntax for the omreport Virtual Disk Commands Table 6-14. omreport Virtual Disk Commands Required Command Levels (1, 2, 3) Optional name=value pairs omreport storage vdisk controller=id where id is the controller number. For example: controller=0. controller=id vdisk=id where id is the controller number and the virtual disk number. For example: controller=0 vdisk=1. Use Displays property information for all virtual disks on all controllers.
omconfig Global Enable Smart Thermal Shutdown By default, the operating system and server shut down when the PV220S and PV221S enclosures reach a critical temperature of 0 or 50° Celsius. However, if you have implemented connector redundancy on the PV220S and PV221S enclosures you can specify that only the enclosure and not the operating system and server be shut down when the enclosure reaches a critical temperature of 0 or 50° Celsius.
Complete Syntax omconfig storage globalinfo action=disablests Example Syntax The omconfig command syntax for disabling thermal shutdown does not require that you specify a controller or enclosure ID. To disable thermal shutdown, enter the following: omconfig storage globalinfo action=disablests NOTE: You can use the omreport storage globalinfo command to determine whether smart thermal shutdown is currently enabled or disabled.
Complete Syntax For dedicated hot spare protection policy, type: omconfig storage globalinfo action= setprotectionpolicies type=dhs raid= hscount=<1-16> warnlevel=<0-3> where hscount is the number of hot spares to be assigned to the virtual disk and warnlevel is the severity level you want to assign to the generated alert, if this policy is violated. Use hscount=0 warnlevel=0 to reset the dedicated hot spare protection policy for the RAID level.
Table 6-16.
Table 6-16.
omconfig Enable Controller Alarm Use the following omconfig command syntax to enable the controller alarm. See the Dell OpenManage Online Help for more information about Enable Controller Alarm. Complete Syntax omconfig storage controller action=enablealarm controller=id where id is the controller ID as reported by the omreport storage controller command.
omconfig Quiet Controller Alarm Use the following omconfig command syntax to silence an activated controller alarm. See the Dell OpenManage Online Help for more information about Quite Controller Alarm. Complete Syntax omconfig storage controller action=quietalarm controller=id where id is the controller ID as reported by the omreport storage controller command.
omconfig Reset Controller Configuration Use the following omconfig command syntax to reset the controller configuration. CAUTION: Resetting a configuration permanently destroys all data on all virtual disks attached to the controller. System or boot partition residing on these virtual disks will be destroyed. You may receive a warning message if this command results in deleting the system or boot partition. However, this warning message is not generated in all circumstances.
Physical disk is specified as either: For SCSI, SATA, and ATA Controllers pdisk=connector:enclosureID:portID where connector:enclosureID:portID is the connector number, enclosure number, and port number. For example pdisk=0:1:2 For SAS Controllers pdisk=connector:targetID where connectorID:targetID is the connector number and the physical disk number. For example: pdisk=0:2 Storage Management supplies default values for any of the other parameters that you do not specify.
[stripesize=< 2kb| 4kb| 8kb| 16kb| 32kb| 64kb| 128kb>] Parameter (Optional) [cachepolicy=] Parameter (Optional) [readpolicy=] Parameter (Optional) [writepolicy=] Parameter (Optional) [name=] Parameter (Optional) [spanlength=] Parameter (Optional) controller=id Parameter (Required) Specify the controller ID as reported by the omreport storage controller command.
size= Parameter (Required) Table 6-18 indicates how to specify the size= parameter. Table 6-18. Size Parameter size= Description Parameter Specification size= size=max size=min Use this specification to indicate a specific size for the virtual disk. The virtual disk size may be specified in b (bytes), m (megabytes), or g (gigabytes). For example, size=500m indicates that the virtual disk should be 500 MB.
[cachepolicy=] Parameter (Optional) Different controllers support different cache policies. Table 6-19 indicates how to specify the [cachepolicy=] parameter for each of the cache policies. Table 6-19. Cache Policy Parameters Cache Policy cachepolicy=d | c Parameter Specification Direct I/O Cache I/O cachepolicy=d cachepolicy=c [diskcachepolicy=] Parameter (Optional) Different controllers support different disk cache policies.
[writepolicy=] Parameter (Optional) Different controllers support different write policies. Table 6-21 indicates how to specify the [writepolicy=] parameter for each of the write policies. Table 6-21.
Example Syntax For example, you may want to create a RAID-5 virtual disk on a PERC 3/QC controller. See the Dell OpenManage Online Help for information on read, write, and cache policies are supported by this controller. For example, to create a virtual disk with the following read, write, and cache policy: • Read-ahead • Write–through caching • Cache I/O The virtual disk will be 500 MB with a stripe size of 16 KB.
Example Syntax To set the rebuild rate to 50 on controller 1, enter: omconfig storage controller action=setrebuildrate controller=1 rate=50 omconfig Set Background Initialization Rate Use the following omconfig command syntax to set the background initialization rate. Complete Syntax omconfig storage controller action=setbgirate controller=id rate=<0 to 100> where id is the controller ID as reported by the omreport storage controller command.
Example Syntax To set the reconstruct rate to 50 on controller 1, enter: omconfig storage controller action= setreconstructrate controller=1 rate=50 omconfig Set Check Consistency Rate Use the following omconfig command syntax to set the check consistency rate. Complete Syntax omconfig storage controller action= setcheckconsistency controller=id rate=<0 to 100> where id is the controller ID as reported by the omreport storage controller command.
Example Syntax To export the log on controller 1, enter: omconfig storage controller action=exportlog controller=1 By default, the log file is exported to C:\WINNT or C:\Windows on Microsoft® Windows® systems (based on the Windows version used) and /var/log on all Linux systems. Depending on the controller, the log file name will either be afa_.log or lsi_.log where is the month and date. See the Dell OpenManage Online Help for more information on the controller log file.
Complete Syntax omconfig storage controller action= importrecoverforeignconfig controller=id where id is the controller ID as reported by the omreport storage controller command. NOTE: This command is supported only in firmware version 5.1.1.
Complete Syntax omconfig storage controller action= setpatrolreadmode controller=id mode=manual|auto|disable where id is the controller ID as reported by the omreport storage controller command. Example Syntax To set the patrol read on controller 1 to manual mode, enter: omconfig storage controller action= setpatrolreadmode controller=1 mode=manual omconfig Start Patrol Read Use the following omconfig command syntax to start the patrol read task on the controller.
Complete Syntax omconfig storage controller action=stoppatrolread controller=id where id is the controller ID as reported by the omreport storage controller command. Example Syntax To stop the patrol read task on controller 1, enter: omconfig storage controller action=stoppatrolread controller=1 NOTE: To be able to stop patrol read, the current patrol read mode should be set to Manual.
omconfig Storage Virtual Disk Use the following omconfig storage command syntax to replace a physical disk that is part of a virtual disk with another physical disk.
omconfig Virtual Disk Commands The following sections provide the omconfig command syntax required to execute virtual disk tasks. CAUTION: The omconfig storage vdisk action=deletevdisk controller=id vdisk=id command deletes a virtual disk. Deleting a virtual disk destroys all information including file systems and volumes residing on the virtual disk. Table 6-22.
omconfig Blink Virtual Disk Use the following omconfig command syntax to blink the physical disks included in a virtual disk. Complete Syntax omconfig storage vdisk action=blink controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
omconfig Initialize Virtual Disk Use the following omconfig command syntax to initialize a virtual disk. Complete Syntax omconfig storage vdisk action=initialize controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller= ID to display the IDs for the virtual disks attached to the controller.
Complete Syntax omconfig storage vdisk action=fastinit controller= id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller= ID to display the IDs for the virtual disks attached to the controller.
omconfig Cancel Background Initialize Use the following omconfig command syntax to cancel the background initialization process on a virtual disk. Complete Syntax omconfig storage vdisk action=cancelbginitialize controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command.
omconfig Split Mirror Use the following omconfig command syntax to separate mirrored data originally configured as a RAID 1, RAID-1–concatenated, or RAID-10 virtual disk. Splitting a RAID-1 or RAID-1–concatenated mirror creates two concatenated non-redundant virtual disks. Splitting a RAID-10 mirror creates two RAID-0 (striped) non-redundant virtual disks. Data is not lost during this operation.
Complete Syntax omconfig storage vdisk action=unmirror controller= id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
Example for SCSI, SATA, and ATA Controllers To assign the dedicated hot spare described in this example, enter: omconfig storage vdisk action= assigndedicatedhotspare controller=1 vdisk=4 pdisk=0:3 assign=yes Example for SAS Controllers To assign the dedicated hot spare described in this example, enter: omconfig storage vdisk action= assigndedicatedhotspare controller=1 vdisk=4 pdisk=0:2:3 assign=yes omconfig Unassign Dedicated Hot Spare Use the following omconfig command syntax to unassign one or more p
Example for SCSI, SATA, and ATA Controllers To unassign the dedicated hot spare described in this example, enter: omconfig storage vdisk action= assigndedicatedhotspare controller=1 vdisk=4 pdisk=0:3 assign=no Example for SAS Controllers To unassign the dedicated hot spare described in this example, enter: omconfig storage vdisk action= assigndedicatedhotspare controller=1 vdisk=4 pdisk=0:2:3 assign=no omconfig Check Consistency Use the following omconfig command syntax to initiate a check consistency on
omconfig Cancel Check Consistency Use the following omconfig command syntax to cancel a check consistency while in progress. Complete Syntax omconfig storage vdisk action= cancelcheckconsistency controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command.
omconfig Resume Check Consistency Use the following omconfig command syntax to resume a check consistency after it has been paused. Complete Syntax omconfig storage vdisk action= resumecheckconsistency controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command.
omconfig Format Virtual Disk Use the following omconfig command syntax to format a virtual disk. Complete Syntax omconfig storage vdisk action=format controller=id vdisk=id where id is the controller ID and virtual disk ID as reported by the omreport command. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage vdisk controller=ID to display the IDs for the virtual disks attached to the controller.
Example for SCSI, SATA, and ATA Controllers In this example, enter: omconfig storage vdisk action=reconfigure controller=1 vdisk=4 raid=r5 size=800m pdisk= 0:0,0:1,0:2,0:3 Example for SAS Controllers In this example, enter: omconfig storage vdisk action=reconfigure controller=1 vdisk=4 raid=r5 pdisk= 0:2:0,0:2:1,0:2:2,0:2:3 omconfig Change Virtual Disk Policy Use the following omconfig command syntax to change a virtual disk’s read, write, or cache policy.
Example Syntax To change the read policy of virtual disk 4 on controller 1 to no-read-ahead, enter: omconfig storage vdisk action=changepolicy controller=1 vdisk=4 readpolicy=nra omconfig Rename Virtual Disk Use the following omconfig command syntax to rename a virtual disk. NOTE: On a CERC SATA 1.5/2s controller, you cannot change the default name of a virtual disk.
Table 6-23.
Example Syntax In this example, you want to blink physical disk 0 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2.
Example Syntax In this example, you want to unblink physical disk 0 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2.
Example for SCSI, SATA, and ATA Controllers To prepare to remove the physical disk described in this example, enter: omconfig storage pdisk action=remove controller=1 pdisk=0:3 Example for SAS Controllers To prepare to remove the physical disk described in this example, enter: omconfig storage pdisk action=remove controller=1 pdisk=0:2:3 omconfig Initialize Physical Disk Use the following omconfig command syntax to initialize a physical disk.
Example for SAS Controllers To initialize the physical disk described in this example, enter: omconfig storage pdisk action=initialize controller=1 pdisk=0:2:3 omconfig Offline Physical Disk Use the following omconfig command syntax to offline a physical disk: Complete Syntax omconfig storage pdisk action=offline controller= id pdisk=connectorID:targetID where id is the controller ID and connectorID:targetID is the connector number and physical disk number as reported by the omreport command.
Example Syntax In this example, you want to offline physical disk 3 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2.
Example for SAS Controllers To bring the physical disk described in this example back online, enter: omconfig storage pdisk action=online controller=1 pdisk=0:2:3 omconfig Assign Global Hot Spare Use the following omconfig command syntax to assign a physical disk as a global hot spare. Complete Syntax omconfig storage pdisk action=assignglobalhotspare controller=id pdisk= assign=yes where id is the controller ID. The variable specifies the physical disk.
omconfig Unassign Global Hot Spare Use the following omconfig command syntax to unassign a physical disk as a global hot spare. Complete Syntax omconfig storage pdisk action=assignglobalhotspare controller=id pdisk= assign=no where id is the controller ID. The variable specifies the physical disk.
omconfig Rebuild Physical Disk Use the following omconfig command syntax to rebuild a failed physical disk. Rebuilding a disk may take several hours. If you need to cancel the rebuild, use the Cancel Rebuild task. See the Dell OpenManage Online Help for more information about Rebuild Physical Disk. Complete Syntax omconfig storage pdisk action=rebuild controller= id pdisk= where id is the controller ID. The variable specifies the physical disk.
Complete Syntax omconfig storage pdisk action=cancelrebuild controller=id pdisk= where id is the controller ID. The variable specifies the physical disk. To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=ID to display the IDs for the physical disks attached to the controller. Example Syntax In this example, you want to cancel the rebuild or physical disk 3 on connector 0 of controller 1.
To obtain these values, enter omreport storage controller to display the controller IDs and then enter omreport storage pdisk controller=ID to display the IDs for the physical disks attached to the controller. Example Syntax In this example, you want to remove dead disk segments on physical disk 3 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2.
Example Syntax In this example, you want to clear physical disk 3 on connector 0 of controller 1. On a SAS controller, the physical disk resides in enclosure 2. Example for SAS Controllers To clear the physical disk described in this example, enter: omconfig storage pdisk action=clear controller=1 pdisk=0:2:3 omconfig Cancel Clear Physical Disk Use the following omconfig command to cancel a clear operation in progress on a physical disk.
Complete Syntax action=cancelreplacemember controller=id pdisk= where id is the physical disk IDs as reported by the omreport command. Example Syntax To cancel replace member operation on disk 0:0:1 which is connected to controller 0, enter: omconfig storage pdisk action=cancelreplacemember controller=0 pdisk=0:0:1 omconfig Battery Commands The following sections provide the omconfig command syntax required to execute battery tasks. Table 6-24.
where id is the controller ID and battery ID as reported by the omreport command. To obtain this value, enter omreport storage controller to display the controller IDs and then enter omreport storage battery controller=ID to display the ID for the controller battery. Example Syntax To recondition the battery on controller 1, enter: omconfig storage battery action=recondition controller=1 battery=0 omconfig Start Battery Learn Cycle Use the following omconfig command to start the battery learn cycle.
where id is the controller ID and battery ID as reported by the omreport command. To obtain this value, enter omreport storage controller to display the controller IDs and then enter omreport storage battery controller=ID to display the ID for the controller battery.
Example Syntax To rescan connector 2 on controller 1, enter: omconfig storage connector action=rescan controller=1 connector=2 omconfig Enclosure Commands The following sections provide the omconfig command syntax required to execute enclosure tasks. Table 6-26.
omconfig Enable Enclosure Alarm Use the following omconfig command syntax to enable the enclosure alarm: Complete Syntax omconfig storage enclosure action=enablealarm controller=id enclosure= where id is the controller ID. The variable specifies the enclosure.
Example for SCSI, SATA, and ATA Controllers To disable the alarm on the enclosure attached to connector 2 on controller 1, enter: omconfig storage enclosure action=disablealarm controller=1 enclosure=2 Example for SAS Controllers To disable the alarm on enclosure 2 attached to connector 1 on controller 1, enter: omconfig storage enclosure action=disablealarm controller=1 enclosure=1:2 omconfig Set Enclosure Asset Tag Use the following omconfig command syntax to specify the enclosure’s asset tag: Complete
omconfig Set Enclosure Asset Name Use the following omconfig command syntax to specify the asset name for an enclosure. Complete Syntax omconfig storage enclosure action=setassetname controller=id enclosure= assetname= where id is the controller ID. The variable specifies the enclosure. In this syntax, is a user-specified alphanumeric string.
where id is the controller ID and the temperature probe ID. The variable specifies the enclosure. In this syntax, “n” is a user-specified value for the temperature in Celsius. Example Syntax For example, you may want to specify the minimum and maximum warning thresholds for temperature probe 3 to 10 and 40° Celsius. Example for SCSI, SATA, and ATA Controllers In this example, temperature probe 3 resides in the enclosure attached to connector 2 on controller 1.
Example for SCSI, SATA, and ATA Controllers In this example, temperature probe 3 resides in the enclosure attached to connector 2 on controller 1. To reset the thresholds for temperature probe 3 to the default values, enter: omconfig storage enclosure action=resettempprobes controller=1 enclosure=2 index=3 omconfig Set All Temperature Probe Thresholds Use the following omconfig command syntax to set the minimum and maximum warning temperature thresholds for all temperature probes in the enclosure.
omconfig Reset All Temperature Probe Thresholds Use the following omconfig command syntax to reset the minimum and maximum warning temperature thresholds back to their default value for all temperature probes in the enclosure. NOTE: This command is not supported on SCSI RAID controllers. Complete Syntax omconfig storage enclosure action= resetalltempprobes controller=id enclosure= where id is the controller ID. The variable specifies the enclosure.
Example for SCSI, SATA, and ATA Controllers To blink the LEDs for the enclosure attached to connector 2 on controller 1, enter: omconfig storage enclosure action=blink controller=1 enclosure=2 Example for SAS Controllers To blink the LEDs for enclosure 3 attached to connector 2 on controller 1, enter: omconfig storage enclosure action=blink controller=1 enclosure=2:3 236 Using the Storage Management Service
Working With CLI Command Results Server Administrator Command Line Interface (CLI) users can use the command output in various ways. This section explains how to save command output to a file and how to select a format for your command results that fits different objectives. Table 7-1.
SUSE® Linux Enterprise Server terminal. To display command output with control over scrolling, type the CLI command and append the pipe symbol followed by more. For example, type: omreport system summary | more or omreport servermodule summary | more The multiscreen system summary displays the first screen. When you want to see the next screen of command output, press the spacebar.
Four hours later, you repeat the command. You have no interest in the 11:00 A.M. snapshot as written to fans.txt. You type the same command: omreport chassis fans index=0 -outc fans.txt or omreport mainsystem fans index=0 -outc fans.txt The 3:00 P.M. data overwrites the 11:00 A.M. data in the fans.txt file. Fans.
Fans.
The available formats include: • List (lst) • Semicolon-separated values (ssv) • Table (tbl) • Raw XML (xml) • Custom delimited format (cdv) The Syntax for the formatting option is: -fmt For example, type: omreport system summary -fmt tbl or omreport servermodule summary -fmt tbl where -fmt tbl specifies table format. You can combine the formatting option with the option to direct output to a file. For example, type: omreport system summary -fmt tbl -outa summary.
No special formatting option is required because list format is the default display format. The network data part of the example system summary appears as follows: -------------Network Data -------------Network Interface Card 0 Data IP Address: 143.166.152.108 Subnet Mask: 255.255.255.0 Default Gateway: 143.166.152.1 MAC Address: 00-02-b3-23-d2-ca Table (tbl) Use the tbl or table formatting option to have your data formatted in table rows and columns.
Semicolon-separated Values (ssv) Use the ssv formatting option to deliver output formatted in semicolonseparated value format. This format also allows you to import your command output results into a spreadsheet program such as Microsoft Excel, or into a database program.
Custom Delimited Format (cdv) Use the cdv formatting option to report exported data in custom delimited format. You can specify this option with any omreport command. For example, to generate a system summary in custom delimited format, type: omreport system summary -fmt cdv or omreport servermodule summary -fmt cdv You can also set preferences for the custom delimited format with the omconfig command.
Glossary The following list defines or identifies technical terms, abbreviations, and acronyms used in Dell™ user documents. A Abbreviation for ampere(s). AC Abbreviation for alternating current. AC power switch A switch with two AC power inputs that provides AC power redundancy by failing over to a standby AC input in the event of a failure to the primary AC input. Access Refers to the actions a user can take on a variable value. Examples include read-only and read-write.
ASPI Advanced SCSI programming interface. ASR Abbreviation for automatic system recovery. ASR consists of those procedures that restore the system to running all properly configured domains after one or more domains have been rendered inactive due to software or hardware failures or due to unacceptable environmental conditions. asset tag code An individual code assigned to a computer, usually by a system administrator, for security or tracking purposes.
baud rate A measurement of data transmission speed. For example, modems are designed to transmit data at one or more specified baud rate(s) through the COM (serial) port of a computer. BGA Abbreviation for Ball Grid Array, an IC package that uses an array of solder balls, instead of pins, to connect to a PC board. binary A base-2 numbering system that uses 0 and 1 to represent information. The computer performs operations based on the ordering and calculation of these numbers.
bpi Abbreviation for bits per inch. bps Abbreviation for bits per second. BTU Abbreviation for British thermal unit. bus An information pathway between the components of a computer. Your computer contains an expansion bus that allows the microprocessor to communicate with controllers for all the various peripheral devices connected to the computer. Your computer also contains an address bus and a data bus for communications between the microprocessor and RAM.
CD-ROM Abbreviation for compact disc read-only memory. CD drives use optical technology to read data from CDs. CDs are read-only storage devices; you cannot write new data to a CD with standard CD drives. certificate authority A certificate authority is an industry-recognized entity. A certificate authority verifies the identity of organizations requesting credentials to identify them to other systems over networks or the Internet.
CMOS Acronym for complementary metal-oxide semiconductor. In computers, CMOS memory chips are often used for NVRAM storage. COMn The device names for the first through fourth serial ports on your computer are COM1, COM2, COM3, and COM4. The default interrupt for COM1 and COM3 is IRQ4, and the default interrupt for COM2 and COM4 is IRQ3. Therefore, you must be careful when configuring software that runs a serial device so that you don't create an interrupt conflict.
cooling unit Sets of fans or other cooling devices in a system chassis. coprocessor A chip that relieves the computer's microprocessor of specific processing tasks. A math coprocessor, for example, handles numeric processing. A graphics coprocessor handles video rendering. The Intel Pentium microprocessor for example, includes a built-in math coprocessor. cpi Abbreviation for characters per inch. CPU Abbreviation for central processing unit. See also microprocessor.
dBA Abbreviation for adjusted decibel(s). DC Abbreviation for direct current. device driver A program that allows the operating system or some other program to interface correctly with a peripheral device, such as a printer. Some device drivers—such as network drivers—must be loaded from the config.sys file (with a device= statement) or as memory-resident programs (usually, from the autoexec.bat file). Others—such as video drivers—must load when you start the program for which they were designed.
DMA Abbreviation for direct memory access. A DMA channel allows certain types of data transfer between RAM and a device to bypass the microprocessor. DMI Abbreviation for Desktop Management Interface. DMI enables the management of your computer system's software and hardware. DMI collects information about the system's components, such as the operating system, memory, peripherals, expansion cards, and asset tag. Information about the system's components is displayed as a MIF file.
DTE Abbreviation for data terminal equipment. Any device, such as a computer system, that can send data in digital form by means of a cable or communications line. The DTE is connected to the cable or communications line through a data communications equipment (DCE) device, such as a modem. ECC Abbreviation for error checking and correction. ECP Abbreviation for Extended Capabilities Port.
Embedded Hypervisor Embedded Hypervisor enhances the virtualization capabilities of your Dell systems. EMC Abbreviation for Electromagnetic Compatibility. EMI Abbreviation for electromagnetic interference. EMM Abbreviation for expanded memory manager. A utility that uses extended memory to emulate expanded memory on computers with an Intel386™ or higher microprocessor. EMS Abbreviation for Expanded Memory Specification.
expanded memory A technique for accessing RAM above 1 MB. To enable expanded memory on your computer, use an EMM. You should configure your system to support expanded memory only if you run application programs that can use (or require) expanded memory. expansion bus Your computer contains an expansion bus that allows the microprocessor to communicate with controllers for peripheral devices, such as a network card or an internal modem.
FIFO Abbreviation for first-in, first-out. In computer programming, FIFO (first-in, first-out) is an approach to handling program work requests from queues or stacks so that the oldest request is handled next. flash bios A PC BIOS that is stored in a flash memory rather than in a ROM. A flash BIOS chip can be updated in place, whereas a ROM BIOS must be replaced with a newer chip.
group As it relates to DMI, a group is a data structure that defines common information, or attributes, about a manageable component. GUI Acronym for graphical user interface. h Abbreviation for hexadecimal. A base-16 numbering system, often used in programming to identify addresses in the computer's RAM and I/O memory addresses for devices. The sequence of decimal numbers from 0 through 16, for example, is expressed in hexadecimal notation as: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F, 10.
HTTPS Abbreviation for HyperText Transmission Protocol, Secure. HTTPS is a variant of HTTP used by Web browsers for handling secure transactions. HTTPS is a unique protocol that is simply SSL underneath HTTP. You need to use "https://" for HTTP URLs with SSL, whereas you continue to use "http://" for HTTP URLs without SSL. Hz Abbreviation for hertz. ICES Abbreviation for Interference-Causing Equipment Standard (in Canada). ICU Abbreviation for ISA Configuration Utility.
internal microprocessor cache An instruction and data cache built in to the microprocessor. The Intel Pentium microprocessor includes a 16-KB internal cache, which is set up as an 8-KB read-only instruction cache and an 8-KB read/write data cache. Internal USB Internal USB flash drive is an additional storage device. Internal USB enhances virtualization capabilities. IP The Internet Protocol (IP) is the method or protocol by which data is sent from one computer to another on the Internet.
used to facilitate data transfers over intranets and to manage storage over long distances. ITE Abbreviation for information technology equipment. jumper Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects the pins and creates a circuit. Jumpers provide a simple and reversible method of changing the circuitry in a printed circuit board. JVM Acronym for Java virtual machine.
kHz Abbreviation for kilohertz, 1,000 hertz. LAN Acronym for local area network. A LAN system is usually confined to the same building or a few nearby buildings, with all equipment linked by wiring dedicated specifically to the LAN. lb Abbreviation for pound(s). LCC Acronym for leaded or leadless chip carrier. LDAP Acronym for Lightweight Directory Access Protocol. A networking protocol for querying and modifying directory services running over TCP/IP. LIF Acronym for low insertion force.
LRA Acronym for local response agent. LS drive A drive that uses laser servo technology to read LS 120 diskettes that hold up to 120 MB of data as well as standard 3.5-inch diskettes. LSI Acronym for large-scale integration. LUN Acronym for logical unit number, a code used to select a specific device among several that share a SCSI ID. mA Abbreviation for milliampere(s). mAh Abbreviation for milliampere-hour(s). math coprocessor See coprocessor. Mb Abbreviation for megabit.
MCA Abbreviation for Micro Channel Architecture, which is designed for multiprocessing. MCA eliminates potential conflicts that arise when installing new peripheral devices. MCA is not compatible with either EISA or XT bus architecture, so older cards cannot be used with it. memory A computer can contain several different forms of memory, such as RAM, ROM, and video memory.
MIF Acronym for management information format. A MIF file contains information, status, and links to component instrumentation. MIF files are installed into the MIF database by the DMI service layer. The content of a MIF is defined by a DTMF working committee and is published in the form of a MIF definition document. This document identifies the groups and attributes that are relevant to DMI-manageable components. mm Abbreviation for millimeter(s).
name The name of an object or variable is the exact string that identifies it in an SNMP Management Information Base (MIB) file, or in a DMI Management Information Format (MIF) file, or in a CIM Management Object File (MOF). NDIS Abbreviation for Network Driver Interface Specification. NIC Acronym for network interface controller. NIF Acronym for network interface function. This term is equivalent to NIC. NIS Abbreviation for Network Information System.
NVRAM Acronym for non-volatile random-access memory. Memory that does not lose its contents when you turn off your computer. NVRAM is used for maintaining the date, time, and system configuration information. OEM Abbreviation for original equipment manufacturer. An OEM is a company that supplies equipment to other companies to resell or incorporate into another product using the reseller's brand name. OID Abbreviation for object identifier.
PCI Abbreviation for Peripheral Component Interconnect. A standard for local-bus implementation developed by Intel Corporation. PCMCIA Personal Computer Memory Card International Association. An international trade association that has developed standards for devices, such as modems and external hard drives, that can be plugged into portable computers. PERC Acronym for Expandable RAID controller.
Plug and Play An industry-standard specification that makes it easier to add hardware devices to personal computers. Plug and Play provides automatic installation and configuration, compatibility with existing hardware, and dynamic support of mobile computing environments. PME Abbreviation for Power Management Event. A PME is a pin on a peripheral component interconnect that allows a PCI device to assert a wake event. POST Acronym for power-on self-test.
protected mode An operating mode supported by 80286 or higher microprocessors, protected mode allows operating systems to implement: • A memory address space of 16 MB (80286 microprocessor) to 4 GB (Intel386 or higher microprocessor) • Multitasking • Virtual memory, a method for increasing addressable memory by using the hard drive The Windows NT, Windows 2000, Windows XP, OS/2®, and UNIX® 32-bit operating systems run in protected mode.
RAM Acronym for random-access memory. The computer's primary temporary storage area for program instructions and data. Each location in RAM is identified by a number called a memory address. Any information stored in RAM is lost when you turn off your computer. RAMBUS Acronym for Rambus® DRAM, a type of memory (DRAM) developed by Rambus, Inc. RAMDAC Acronym for random-access memory digital-to-analog converter. Raw Unprocessed.
readme file A text file included with a software package or hardware product that contains information supplementing or updating the documentation for the software or hardware. Typically, readme files provide installation information, describe new product enhancements or corrections that have not yet been documented, and list known problems or other things you need to be aware of as you use the software or hardware.
RTC Abbreviation for real-time clock. Battery-powered clock circuitry inside the computer that keeps the date and time after you turn off the computer. SAS Acronym for Serial Attached SCSI. SCA Acronym for single connector attachment. schema A collection of class definitions that describes managed objects in a particular environment.
service tag number A bar code label on the computer that identifies it when you call Dell for customer or technical support. SGRAM Acronym for synchronous graphics RAM. shadowing A computer's system and video BIOS code is usually stored on ROM chips. Shadowing refers to the performance-enhancement technique that copies BIOS code to faster RAM chips in the upper memory area (above 640 KB) during the boot routine. SIMD Abbreviation for Single Instruction Multiple Data.
SMTP Acronym for Simple Mail Transfer Protocol, a method for exchanging e-mail over the internet. SNMP Abbreviation for Simple Network Management Protocol. SNMP is an industry-standard interface that allows a network manager to remotely monitor and manage workstations. SODIMM Acronym for small outline-DIMM. A DIMM module with a thinner profile due to the use of TSOP chip packages. SODIMMs are commonly used in laptop computers. SRAM Abbreviation for static random-access memory.
Two common DIP switches are used on system boards: slide switches and rocker switches. The names of the switches are based on how the settings (on and off) of the switches are changed. syntax The rules that dictate how you must type a command or instruction so that the computer understands it. A variable's syntax indicates its data type.
system.ini file A start-up file for the Windows operating system. When you start Windows, it consults the system.ini file to determine a variety of options for the Windows operating environment. Among other things, the system.ini file records which video, mouse, and keyboard drivers are installed for Windows. Running the Control Panel or Windows Setup program may change options in the system.ini file. On other occasions, you may need to change or add options to the system.
• LowerThresholdNon-critical • LowerThresholdCritical • LowerThresholdFatal time-out A specified period of system inactivity that must occur before an energy conservation feature is activated. tpi Abbreviation for tracks per inch. TPM Acronym for Trusted Platform Module TQFP Acronym for thin quad flat pack. TSR Abbreviation for terminate-and-stay-resident. A TSR program runs “in the background.
UMB Abbreviation for upper memory blocks. unicode A fixed width, 16-bit world wide character encoding, developed and maintained by the Unicode Consortium. upper memory area The 384 KB of RAM located between 640 KB and 1 MB. If the computer has an Intel386 or higher microprocessor, a utility called a memory manager can create UMBs in the upper memory area, in which you can load device drivers and memory-resident programs. UPS Abbreviation for uninterruptible power supply.
varbind An algorithm used to assign an object identifier or OID. The varbind gives rules for arriving at the decimal prefix that uniquely identifies an enterprise, as well as the formula for specifying a unique identifier for the objects defined in that enterprise's MIB. variable A component of a managed object. A temperature probe, for example, has a variable to describe its capabilities, its health or status, and certain indexes that you can use to help you locate the right temperature probe.
for displaying popular application programs and operating systems in a variety of video modes. On some Dell computers, a video adapter is integrated into the system board. Also available are many video adapter cards that plug into an expansion-card connector. Video adapters often include memory separate from RAM on the system board. The amount of video memory, along with the adapter's video drivers, may affect the number of colors that can be simultaneously displayed.
virus A self-starting program designed to cause inconvenience. Virus programs have been known to corrupt the files stored on a hard drive or to replicate themselves until a computer or network runs out of memory. The most common way that virus programs move from one computer to another is through “infected” diskettes, from which they copy themselves to the hard drive.
WH Abbreviation for watt-hour(s). Winbind A program that allows users in a heterogeneous network to log in using workstations that have UNIX operating systems. The program makes workstations using UNIX functional in Windows domains, by making Windows appear like UNIX to each UNIX workstation. win.ini file A start-up file for the Windows operating system. When you start Windows, it consults the win.ini file to determine a variety of options for the Windows operating environment.
ZIP A 3.5-inch removable disk drive from Iomega. Originally, it provided a 100-MB removable cartridges. The drive is bundled with software that can catalog the disks and lock the files for security. A 250-MB version of the Zip drive also reads and writes the 100-MB Zip cartridges.
Index Symbols -? omconfig, 85 omconfig chassis, 87 omreport, 35 request for help, 23 alertlog clearing logs, 135 omconfig system, 23, 80 omreport system, 61 arrays memory, 31, 72 asset information, 147 A about omconfig, 86 acquisition information, 148 optional parameters, 25 assetinfo acquisition, 64 omreport system, 64 assign dedicated hot spare omconfig, 206 assign global hot spare omconfig, 220 acquisition information adding, 148 available alert actions, 131 acswitch omreport chassis, 38 omreport c
bios omreport chassis, 40 change virtual disk policy omconfig, 212 biossetup omconfig chassis, 87 omreport chassis, 40 chassis omconfig, 87 blink omconfig, 235 chassis identification LED, 105 blink physical disk omconfig, 214 bmc omconfig chassis, 100, 110 omreport chassis, 43, 58 chassis fault LED, 105 chassis information summary, 46 check consistency omconfig, 208 check consistency rate omconfig, 194 clear foreign configuration omconfig, 196 C cache policy parameters, 190 cache properties omreport
CLI commands ?, 23 primary commands, 17 Windows command prompt, 17 cmdlog omconfig system, 135 omreport system, 61 command levels 1,2, and 3 omconfig, 78 command levels 1,2,3 omreport, 29 command syntax overview, 21 commands for clearing logs, 135 commands for viewing logs, 61 components alert actions, 132 event notification, 140 events, 64-65 failure messages, 19 instrumentation service, 77 omreport, 27-28 omreport system, 60 omreport system summary, 34 omreport system version, 34 SNMP traps, 139 storage,
D data bus width omreport chassis slots, 59 default maximum warning threshold, 100 default minimum warning threshold, 100 defining alert actions, 130 delay battery learn cycle omconfig, 227 delete virtual disk omconfig, 210 delimiters data fields, 125 depreciation information about, 150 adding, 150 dirservice omconfig preferences, 126 disable enclosure alarm omconfig, 230 display IDs, 167-168 E enable enclosure alarm omconfig, 230 enclosure omconfig storage, 229 omreport storage, 172-176 288 Index error
F I failure messages, 19 import foreign configuration omconfig, 195 fan status omreport, 174 fancontrol omconfig chassis, 101 omreport chassis, 44 fans omconfig chassis, 100 omreport chassis, 44 index omreport chassis slots, 59 info omconfig chassis, 103 omreport chassis, 46 initialize physical disk omconfig, 217 firmware omreport chassis, 44 initialize virtual disk omconfig, 202 format virtual disk, 211 introduction, 15 formatting CLI command output, 240 intrusion omreport chassis, 47 frontpane
M maintenance information, 154 adding, 154 manufacturer omreport chassis processors, 50 maximum speed omreport chassis ports, 50 maximum warning threshold, 123 memory arrays, 31, 72 omreport chassis, 48 memorymode omconfig chassis, 105 minimum warning threshold, 123 N name=value pairs omconfig chassis biossetup, 88 omconfig chassis bmc, 111 nics omreport chassis, 49 NMI button, 45 O offline physical disk omconfig, 218 omconfg cancel initialize virtual disk, 202 290 Index omconfig -?, 85 about, 86 assign
prepare to remove physical disk, 216 quiet controller alarm, 185 rebuild physical disk, 222 recondition battery, 226 reconfiguring virtual disks, 211 remove dead segments, 223 rename virtual disk, 213 rescan connector, 228 rescan controller, 183 reset controller configuration, 186 reset temperature probe thresholds, 233-235 restore dead segments, 204 resume check consistency, 210 set controller rebuild rate, 192 set enclosure asset name, 232 set enclosure asset tag, 231 set temperature probe thresholds, 232
name=value pairs, parameters, 106 omconfig chassis temps name=value pairs, paramaters, 122 omconfig chassis volts name=value pairs, parameters, 124 omconfig command, 77 omconfig controller commands, 181 omconfig enclosure commands, 229 omconfig global commands, 178 omconfig physical disk commands, 213 omconfig preferences, 125 cdvformat, 125 dirservice, 126 snmp, 127 useraccess, 128 webserver, 129 omconfig preferences dirservice name=value pair, parameters, 126 omconfig preferences snmp name=value pairs, pa
omconfig system pedestinations name=value pairs, parameters, 136 omconfig system recovery name=value pairs, parameters, 142 omconfig system shutdown name=value pairs, parameters, 143 omconfig system warranty, 163 omconfig system webserver name=value pairs, parameters, 142 omconfig virtual disk commands, 200 omhelp, 17, 23 omreport -?, 35 about, 37 battery status, 171 chassis, 38 command levels 1, 2, 3, 29 command summary, 28 connector status, 171 controller status, 170 EMM status, 176 enclosure status, 172
esmlog, 61 events, 64 operatingsystem, 66 pedestinations, 66 platformevents, 68 recovery, 68 shutdown, 68 summary, 68 thrmshutdown, 73 version, 74 maximum speed, 50 port type, 50 omreport chassis processors cache properties, 51 connector name, 50 core count, 51 current speed, 50 external clock speed, 51 manufacturer, 50 processor family, 50 processor version, 50 state, 51 omreport chassis slots adapter, 59 data bus width, 59 index, 59 slot ID, 59 omreport modularchassis, 35 omreport preferences commands, 7
pdisk, 213 omconfig storage, 165-166 omconfig virtual disk, 187 omreport physical disk, 177 omreport storage, 177 R pedestinations omconfig system, 135 omreport system, 66 recondition battery omconfig, 226 Physical disks in each stripe, 191 platformevents omconfig system, 136 omreport system, 68 read policy parameters, 190 rebuild physical disk omconfig, 222 reconfiguring virtual disks omconfig, 211 reconstruct rate omconfig, 193 port type omreport chassis ports, 50 recovery omconfig system, 142 omr
S scripting, 20 scripting with the CLI, 20 separate mirrored data, 205 service contract information, 159 adding, 159 set enclosure asset name omconfig, 232 split mirror omconfig, 205 start battery learn cycle omconfig, 227 state omreport chassis processors, 51 storage management, 165 storage management CLI, 165 successful commands, 19 set enclosure asset tag omconfig, 231 summary omreport system, 68 set temperature probe thresholds omconfig, 232-235 support information adding, 160 shutdown omconfig sy
thermal shutdown about, 73 configuring, 144 example commands, 145 thrmshutdown omconfig system, 144 omreport system, 73 U unassign dedicated hot spare omconfig, 207 unassign global hot spare omconfig, 221 unblink physical disk omconfig, 215 unmirror omconfig, 205 user access to Server Administrator administrators only, 129 determining, 129 least restrictive, 129 most restrictive, 129 power users and administrators only, 129 useraccess omconfig preferences, 128 omreport storage, 178 version omreport system
Index 298
