OptiPlex 3080 Small Form Factor Service Manual Regulatory Model: D15S Regulatory Type: D15S002 May 2020 Rev.
Märkused, ettevaatusabinõud ja hoiatused MÄRKUS: MÄRKUS tähistab olulist teavet, mis aitab teil toodet paremini kasutada. ETTEVAATUST: ETTEVAATUST tähistab teavet, mis hoiatab võimaliku riistvarakahju või andmekao eest ja annab juhiseid selle probleemi vältimiseks. HOIATUS: HOIATUS tähistab teavet, mis hoiatab võimaliku varakahju või tervisekahjustuse või surma eest. © 2020 Dell Inc. või selle tütarettevõtted. Kõik õigused on kaitstud. Dell, EMC ja muud kaubamärgid on ettevõtte Dell Inc.
Contents 1 Arvutiga töötamine....................................................................................................................... 5 Ohutusjuhised.........................................................................................................................................................................5 Enne arvuti sees toimetamist.........................................................................................................................................
Removing the WLAN card............................................................................................................................................30 Installing the WLAN card...............................................................................................................................................31 Jahutusradiaator.................................................................................................................................................................
1 Arvutiga töötamine Ohutusjuhised Et kaitsta arvutit viga saamise eest ja tagada enda ohutus, kasutage järgmisi ohutusjuhiseid. Kui pole teisiti märgitud, eeldab iga selles dokumendis sisalduv toode, et olete arvutiga kaasas olevat ohutusteavet lugenud. MÄRKUS: Enne arvuti sisemuses tegutsema asumist tutvuge arvutiga kaasas oleva ohutusteabega. Ohutuse heade tavade kohta leiate enam teavet nõuetele vastavuse kodulehelt veebiaadressil www.dell.com/regulatory_compliance.
5. Kui arvutiga on ühendatud meediumikaarte või optilisi draive, siis eemaldage need. Ohutuse ettevaatusabinõud Ohutuse ettevaatusabinõude peatükis kirjeldatakse peamisi toiminguid, mis tuleb enne lahtivõtmisjuhiste järgimist teha. Järgige lahtivõtmist või kokkupanekut hõlmava paigaldamis- või parandustoimingute tegemisel järgmisi ohutuse ettevaatusabinõusid. • • • • • • Lülitage süsteem ja kõik ühendatud välisseadmed välja. Lahutage süsteemi ja kõigi ühendatud välisseadmete vahelduvvoolutoide.
Elektrostaatilise lahenduse (ESD) välikomplekt Mittejälgitav välikomplekt on kõige sagedamini kasutatav hoolduskomplekt. Igasse välikomplekti kuuluvad kolm põhikomponenti: antistaatiline matt, randmerihm ja ühenduskaabel. ESD välikomplekti osad ESD välikomplekt koosneb järgmistest osadest. • • • • • • • Antistaatiline matt: antistaatiline matt hajutab elektrit ja hooldustööde ajal saab sellele asetada detaile.
2 Tehnoloogia ja komponendid Selles peatükis täpsustatakse süsteemi tehnoloogiat ja saadaolevaid komponente. Teemad: • • Graafikavalikud Süsteemihalduse funktsioonid Graafikavalikud Intel UHD 610 graafika Tabel 1.
Tabel 2. Intel UHD 630 graafika tehnilised andmed(jätkub) Intel UHD 630 graafika i3/i5/i7: GT2 (UHD) Ülekattetasandid Jah Operatsioonisüsteemide graafika / video API tugi DirectX 12, OpenGL (4,5 Intel CML POR-ist) Toetab maksimaalset eraldusvõimet • • • • • DP: 4096 × 2304 sagedusel 60 Hz, 24 bpp Valikuline DP: 4096 × 2304 sagedusel 60 Hz Valikuline USB-C alternatiivrežiim: 4096 × 2304 sagedusel 60 Hz Valikuline VGA: 1920 × 1200 sagedusel 60 Hz Valikuline HDMI 2.
Tabel 3. NVIDIA GeForce GT 730 tehnilised andmed(jätkub) Funktsioon Väärtused Trükkplaadi jootemask Roheline Klambri kujutegur Madal profiil Maksimaalne eraldusvõime 3840 × 2160 Energiatarve u • 20 W TDP 30 W TGP 3DMarki jõudlus • • 3DMark 11 (P): E4131 3Dmark Vantage(P): AMD Radeon RX640 Tabel 4. AMD Radeon RX640 tehnilised andmed Funktsioon Väärtused GPU sagedus 1,2 GHz DirectX 12 Varjutaja mudel 5,0 Open CL 2,0 Open GL 4,5 GPU mäluliides 128-bitine PCIe-siin PCIe 3.
Tabel 4. AMD Radeon RX640 tehnilised andmed(jätkub) Funktsioon Väärtused 3DMarki jõudlus 3DMark 11 (P): 5315 AMD Radeon R5 430 Tabel 5. AMD Radeon R5 430 tehnilised andmed Funktsioon Väärtused GPU sagedus 780 MHz DirectX 11,2 Varjutaja mudel 5,0 Open CL 1,2 Open GL 4,2 GPU mäluliides 64-bitine PCIe-siin PCIe 3.0 x8 Ekraani tugi Üks DisplayPort 1.
Pakume valikuliselt ka ribavälist haldust. Ribaväline haldus tähendab seda, et süsteemil puudub toimiv operatsioonisüsteem või see on välja lülitatud ja soovite endiselt süsteemi selles olekus hallata. Dell Client Command Suite ribasiseste süsteemide halduseks Dell Client Command Suite on tasuta tööriistakomplekt, mille saab kõigile Latitude Ruggedi tahvelarvutitele aadressilt dell.com/support alla laadida ning mis automatiseerib ja lihtsustab süsteemihalduse ülesandeid, säästes aega, raha ja ressursse.
3 Hooldusteave Recommended tools The procedures in this document require the following tools: • • • • • Phillips #0 screwdriver Phillips #1 screwdriver Philips #2 screwdriver Plastic scribe-Recommended for field technician T-30 torx screwdriver Screw List The following table shows the screw list and the images for different components. Table 6. Screw list Component Screw type Quantity FIO bracket 6-32 2 M.
Steps 1. Press down on the release latch until your hear a click. 2. Slide the side cover towards the back of the system. 3. Lift the side cover from the system.
Installing the side cover Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the side panels and provides a visual representation of the installation procedure.
Steps 1. Locate the side cover slot on your computer. 2. Slide the side cover towards the front of the system till you hear the release latch click. Next steps 1. Follow the procedure in after working inside your computer. Sissetungilüliti Removing the intrusion switch Prerequisites 1. Follow the procedure in Before working inside your computer. 2.
About this task The following image indicates the location of the intrusion switch and provides a visual representation of the installation procedure. Steps 1. Insert the intrusion switch into the slot on the chassis. 2. Connect the intrusion switch cable to the system board . Next steps 1. Install the Side cover 2. Follow the procedure in After working inside your computer. Esiraam Removing the front bezel Prerequisites 1. Follow the procedure in before working inside your computer. 2.
Steps 1. Pry the retention tabs to release the front bezel from the system. 2. Remove the front bezel from the system. Installing the front bezel Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the front bezel and provides a visual representation of the installation procedure.
Steps 1. Position the bezel to align the tab holders with the slots on the system chassis. 2. Press the bezel until the tabs click into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Kõvakettasõlm Removing the 2.5 in. hard drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. About this task The following images indicate the location of the 2.5 in.
Steps 1. Disconnect the hard drive data cable and power cable from the connectors on the hard drive. 2. Remove the 6-32 screw. 3. Release the hard drive assembly from the notch and slide the hard drive assembly out. NOTE: Note the orientation of the hard drive so that you can replace it correctly. Removing the hard drive bracket Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the side cover. Remove the front bezel. Remove the 2.5 in. hard drive assembly.
Steps 1. Locate the hard drive bracket on your computer. 2. Remove the eight M3x3 screws from the hard drive bracket. Installing the 2.5 in. hard drive assembly Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the 2.5 in. hard drive and provides a visual representation of the installation procedure.
Steps 1. 2. 3. 4. Insert the hard drive assembly into the slot on the system and slide the hard drive assembly down. Press down the hard drive assembly, until it clicks into place. Replace the 6-32 screw to fix the hard drive assembly. Connect the power cable and hard drive cable to the connectors on the hard drive. Next steps 1. Install the front bezel. 2. Install the side cover. 3. Follow the procedure in after working inside your computer.
Steps 1. Replace the eight M3x3 screws to secure the hard drive bracket. 2. Align and insert the drive bracket with the slots on the drive. Next steps 1. 2. 3. 4. Install the 2.5 in. hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer. Välkdraiv Removing the M.2 2230 PCIe solid-state drive Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover.
3. Remove the front bezel. 4. Remove the 2.5 in. hard drive assembly. About this task The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure. Steps 1. Remove the screw (M2x3) that secures the solid-state drive to the system board. 2. Slide and lift the solid-state drive off the system board. Installing the M.
Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive slot. 2. Insert the solid-state drive at a 45-degree angle into the system board. 3. Replace the screw (M2X3) that secures the M.2 PCIe solid-state drive to the system board. Next steps 1. 2. 3. 4. Install the 2.5 in. hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer. Removing the M.2 2280 PCIe solid-state drive Prerequisites 1. 2. 3. 4.
Steps 1. Remove the screw (M2x3) that secures the solid-state drive to the system board. 2. Slide and lift the solid-state drive off the system board. Installing the M.2 2280 PCIe solid-state drive Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure.
Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive slot. 2. Insert the solid-state drive at a 45-degree angle into the system board. 3. Replace the screw (M2X3) that secures the M.2 PCIe solid-state drive to the system board. Next steps 1. 2. 3. 4. Install the 2.5 in. hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer. Optiline draiv Removing the slim optical-drive Prerequisites 1.
Steps 1. 2. 3. 4. Press the release tab on the optical drive/ hard drive module. Slide the optical drive out of the optical drive/ hard drive module. Optical drive unit. Optical drive/ hard drive module. Installing the slim optical-drive Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist.
About this task The following image indicates the location of the slim optical-drive and provides a visual representation of the installation procedure. Steps 1. 2. 3. 4. Optical drive/ hard drive module. Optical drive unit. Insert the optical drive into the optical drive/ hard drive module. Press the Optical drive unit until it clicks in place. Next steps 1. Install the Side cover 2. Install the Front bezel 3. Follow the procedure in After working inside your computer.
WLAN-kaart Removing the WLAN card Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the side cover. Remove the front bezel. Remove the 2.5 in. hard drive assembly. About this task The following images indicate the location of the wireless card and provide a visual representation of the removal procedure. Steps 1. 2. 3. 4. 30 Remove the (M2x3) screw that secures the WLAN card to the system board. Lift the WLAN card bracket away from the WLAN card.
Installing the WLAN card Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the wireless card and provides a visual representation of the installation procedure. Steps 1. Connect the antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN card of your computer. Table 7.
4. Replace the (M2x3) screw to secure the plastic tab to the WLAN card. Next steps 1. 2. 3. 4. Install the 2.5 in. hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer. Jahutusradiaator Removing the heat-sink Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel.
About this task The following image indicates the location of the VR heat sink and provides a visual representation of the installation procedure. Steps 1. Place the heat sink on the processor. 2. Tighten the captive screws that secure the heat-sink to the system board and connect the heat sink fan cable to the system board. Next steps 1. Install the front bezel. 2. Install the side cover. 3. Follow the procedure in after working inside your computer.
Steps 1. Using a plastic scribe, gently pry the coin-cell battery out of the slot on the system board. 2. Remove the coin-cell battery away from the system. Installing the coin-cell battery Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the coin-cell battery and provides a visual representation of the installation procedure.
Steps 1. Insert the coin cell battery with the "+" sign facing up and slide it under the securing tabs at the positive side of the connector. 2. Press the battery into the connector until it locks into place. Next steps 1. Install the front bezel. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. Laienduskaart Removing the expansion card Prerequisites 1. Follow the procedure in Before working inside your computer. 2.
Steps 1. Pull the metal tab to open the expansion card latch. 2. Pull the release tab at the base of the expansion card. 3. Lift the expansion card away from the connector on the system board. Installing the graphics card Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist. About this task The following image indicates the location of the graphics card and provides a visual representation of the installation procedure.
Steps 1. Align the expansion card with the connector on the system board. 2. Place the card in the connector and press down firmly. Ensure that the card is firmly seated. 3. Close the expansion card latch and press it until it clicks into place. Next steps 1. Install the Side cover 2. Follow the procedure in After working inside your computer. Mälumoodulid Removing the memory modules Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3.
4. Remove the 2.5 in. hard drive assembly. About this task The following images indicate the location of the memory modules and provide a visual representation of the removal procedure. Steps 1. Pull the securing clips from the memory module until the memory module pops up. 2. Slide and remove the memory module from the memory-module slot. Installing the memory modules Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist.
Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory module and reinstall it. Next steps 1. 2. 3. 4. Install the 2.5 in. hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer. Protsessor Removing the processor Prerequisites 1.
Steps 1. Press down and push the release lever away from the processor to release it from the securing tab. 2. Lift the lever upward to lift the processor cover. CAUTION: When removing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket. 3. Gently lift the processor from the processor socket. Installing the processor Prerequisites Kui asendate komponenti, eemaldage olemasolev komponent enne protseduuri sooritamist.
Steps 1. Align the pin-1 corner of the processor with the pin 1 corner of the processor socket, and then place the processor in the processor socket. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated properly. 2.
Toiteplokk Removing the power-supply unit Prerequisites 1. 2. 3. 4. Follow the procedure in Before working inside your computer. Remove the Side cover Remove the Front bezel Remove the Hard drive and optical drive module NOTE: Note the routing of cables as you must route them again after you complete the task. About this task The following images indicate the location of the power-supply unit and provide a visual representation of the removal procedure.
Hooldusteave 43
Hooldusteave
Steps 1. 2. 3. 4. 5. 6. Unroute the SATA cables from the retention clip on the support bracket. Remove the two screws (M6X32) and slide the support bracket out from the slot. Unroute the power-supply cable from the retention clip on the chassis. Remove the three screws (M6X32) that secure the power-supply unit to the back of the chassis. Press the power-supply unit release latch and slide the unit into the chassis. Remove the power-supply unit out of the chassis.
Hooldusteave
Hooldusteave 47
Hooldusteave
Steps 1. 2. 3. 4. 5. 6. Align and place the power-supply unit into the slot on the chassis. Slide the power-supply unit into the slot until it clicks in place. Replace the three screws (M6X32) to secure the power-supply unit to the chassis. Reroute the power-supply cables through retention clips and connect it to the connectors on the system board. Place the support bracket into the slot and secure it with the two screws (M6X32). Reroute the SATA cables through the retention clip on the support bracket.
Hooldusteave
Hooldusteave 51
Steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Remove the screw (6-32) that secures the I/O panel. Lift the I/O panel away from the system board. Disconnect the intrusion switch cable. Disconnect the system board power supply cables. Disconnect the power button switch cable. Disconnect the system fan cable. Disconnect the processor power supply cable. Disconnect the SATA cables. Disconnect the SATA power cable. Disconnect the internal speaker cable.
Hooldusteave 53
Hooldusteave
Steps 1. Align and lower the system board into the system until the connectors at the back of the system board align with the slots on the chassis, and the screw holes on the system board align with the standoffs on the system. 2. Replace the four screws (6-32) and the single standoff screw (M2X4) screw to secure the system board to the chassis. 3. Align and lower the I/O panel into the slot on the chassis. 4. Replace the screws (6-32) to secure the I/O panel to the chassis. 5.
5. 6. 7. 8. 56 Install the hard drive assembly. Install the front bezel. Install the side cover. Follow the procedure in after working inside your computer.
4 Tõrkeotsing Dell SupportAssisti algkäivituseelse süsteemi toimivuse kontrolli diagnostika See ülesanne SupportAssisti tugidiagnostika (nimetatakse ka süsteemidiagnostikaks) teeb täieliku riistvarakontrolli. SupportAssisti algkäivituseelse süsteemi toimivuse kontrolli diagnostika on manustatud BIOS-i ja BIOS käivitab selle sisemiselt. Manustatud süsteemidiagnostika annab valikud konkreetsete seadmete või seadmegruppide jaoks, võimaldades teha järgmist.
Tabel 8. Diagnostika LED-tule käitumine(jätkub) Vilkuv muster Merevaigukollane 2 Valge 2 Rikke kirjeldus Emaplaadi rike (hõlmab BIOS-i riket või ROM-i tõrget) Soovitatud lahendus • Kui probleem kordub, vahetage emaplaat välja. • Minge tagasi viimase BIOS-i versiooni juurde Kui probleem kordub, vahetage emaplaat välja. • 2 3 Ei leitud mälu/RAM-i • • 2 4 Mälu/RAM-i rike • • Lähtestage mälumoodul. Kui probleem kordub, vahetage mälumoodul välja.
Tabel 8. Diagnostika LED-tule käitumine(jätkub) Vilkuv muster Merevaigukollane Valge Rikke kirjeldus Soovitatud lahendus • Kui probleem kordub, vahetage emaplaat välja. Diagnostilised tõrketeated Tabel 9. Diagnostilised tõrketeated Tõrketeated Kirjeldus AUXILIARY DEVICE FAILURE Puuteplaat või väline hiir võivad olla rikkis. Kontrollige välise hiire puhul kaabliühendust. Aktiveerige valik Pointing Device (Osutusseade) süsteemi seadistuse programmis.
Tabel 9. Diagnostilised tõrketeated(jätkub) Tõrketeated Kirjeldus Seejärel lülitage arvuti välja, paigaldage kõvaketas uuesti ja taaskäivitage arvuti. Kui probleem püsib, proovige teist ketast. Käivitage testid Hard Disk Drive (Kõvaketas) jaotises Dell Diagnostics (Delli diagnostika). HARD-DISK DRIVE FAILURE Kõvaketas ei reageeri arvuti käskudele. Lülitage arvuti välja, eemaldage kõvaketas ja tehke arvuti algkäivitus optiliselt kettalt.
Tabel 9. Diagnostilised tõrketeated(jätkub) Tõrketeated Kirjeldus NO BOOT DEVICE AVAILABLE Arvuti ei leia kõvaketast. Kui kõvaketas on algkäivituse seade, siis veenduge, et ketas oleks paigaldatud, õigesti paigas ja sektsioonitud algkäivituse seadmena. NO BOOT SECTOR ON HARD DRIVE Operatsioonisüsteem võib olla rikutud, pöörduge Delli poole. NO TIMER TICK INTERRUPT Emaplaadil võib mõne kiibi töö häiritud olla.
Süsteemi tõrketeated Tabel 10. Süsteemi tõrketeated Süsteemi teade Kirjeldus Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support Arvuti ei suutnud sama tõrke puhul kolm korda järjest algkäivituse protseduuri lõpule viia. CMOS checksum error RTC on lähtestatud, valiku BIOS Setup vaikesäte on laaditud. CPU fan failure CPU ventilaatori rike.
5 Abi saamine Teemad: • Delli kontaktteave Delli kontaktteave Eeltingimused MÄRKUS: Kui teil pole aktiivset Interneti-ühendust, võite leida kontaktteavet oma ostuarvelt, saatelehelt, tšekilt või Delli tootekataloogist. See ülesanne Dell pakub mitut veebi- ja telefonipõhist toe- ning teenindusvõimalust. Saadavus võib riigi ja toote järgi erineda ning mõned teenused ei pruugi olla teie piirkonnas saadaval. Delliga müügi, tehnilise toe või klienditeeninduse küsimustes ühenduse võtmiseks: Sammud 1. 2. 3. 4.