OptiPlex 3080 Micro Service Manual Regulatory Model: D14U Regulatory Type: D14U002 November 2020 Rev.
កំណត់ចំណាំ ការប្រុងប្រយ័ត្ន និងការព្រមានប្រាប់ ចំ ណាំ : កំ ណ ត់ ចំ ណាំ ប ង្ ហា ញពី ព័ ត មានសំ ខា ន់ ៗ ដែលអាចជួ យ ែល់ លោកអ្ ន ក លៅក្ នុ ង ការប្ ល រី ប្ រា ស់ ផ លិ ត ផលរបស់ អ្ ន កកាន់ ដតប្ រ លសរលឡង ។ ប្ រ យ័ ត្ ន : ការប្ រុ ង ប្ រ យ័ ត្ ន បង្ ហា ញពី កា រខូ ច ខាតធ្ ង ន់ ធ្ ង រលៅលលហាែដែរឬការបាត់ ប ង់ ទិ ន្ ន ន័ យ និ ង ប្ រា ប់ ែ ល់ លោកអ្ ន កអំ ពី រ ប្ លរ បលជ សវាងនូ ែ បញ្ ហា ទាំ ង អស់ លនះ ។ ការព្ រ មាន: ការព្ រ មាន ការព្ រ មានបង្ ហា ញពី ស ក្ តា នុ ព លដែលនាំ ឱ្ យ មានការខូ ច ខាតែល់ ទ្ រ ព្ យ សម្ ប ត្ តិ របួ ស លលែង
Contents Chapter 1: ការធ្ល ែីកា រលៅលលកុំ ព្ យូ ទ័ ររបស់ អ្ ន ក.............................................................................................................5 ការដណនាំអំពីសុែត្ថិភាព............................................................................................................................................................................5 មុន នឹង ធ្ល ែីកា រលៅខាងក្ នុ ង កុំព្ យូទ័ រ របស់ អ្ ន ក........................................................................................
Removing the speaker................................................................................................................................................36 Installing the speaker.................................................................................................................................................. 37 មាូឌុ ល I/O ដែលជាជម្ ល រី ស (ប្ រ លេទ C/ HDMI/VGA/DP/Serial)........................................................................................................
1 ការធ្ល ែីការលៅលលកុំព្យូទ័ររបស់អ្នក ប្រធានបទ : • ការដណនាំ អំ ពី សុ ែ ត្ ថិ ភា ព ការដណនាំអំពីសុែត្ថិភាព ប្ ល រី កា រដណនាំ សុ ែ ត្ ថិ ភា ពែូ ច ខាងក្ លរាមលែម្ បី កា រពារកុំ ព្ យូ ទ័ រ របស់ អ្ ន កពី កា រខូ ច ខាតធ្ ង ន់ ធ្ ង រ និ ង លែម្ បី ធា នានូ ែ សុ ែ ត្ ថិ ភា ពផ្ ទា ល់ ខ្ លួ ន របស់ អ្ ន ក។ ែិ ធី សា ស្ ត្ រ នី មួ យ ៗដែលមានក្ នុ ង ឯកសារលនះ សន្ ម ត់ ថា អ្ ន កបានអានព័ ត៌ មា នសុ ែ ត្ ថិ ភា ពដែលេ្ ជា ប់ ជា មួ យ កុំ ព្ យូ ទ័ រ របស់ អ្ ន ករួ ច លហយ លលកលលងដតមានកំ ណ ត់ ស ម្ គា ល់ ផ្ លសងពី លនះ។ ចំ ណាំ : មុ ន នឹ ង ធ្
បម្រុងប្រយ័ត្នសុែត្ថិភាព ជំ ពូ ក បម្ រុ ង ប្ រ យ័ ត្ ន សុ ែ ត្ ថិ ភា ពលរ បរាប់ ល ម្ អិ ត អំ ពី ជំ ហា នបឋមដែលត្ រូ ែ ធ្ ល ែី មុ ន លពលអនុ ែ ត្ ត តាមការដណនាំ លដាះគ្ លរំងបន្ ោ ស់ ណា មួ យ ។ សង្ លកតលមលបំ រុ ង បម្ រុ ង ប្ រ យ័ ត្ ន សុ ែ ត្ ថិ ភា ពខាងក្ លរាមមុ ន នឹ ង អ្ ន កធ្ ល ែី កា រតម្ លលង ឬែំ លណរការ លដាះ/ជួ ស ជុ ល ណាមួ យ ដែលពាក់ ព័ ន្ ធ នឹ ង ការលដាះគ្ លរំង ឬតម្ លលងគ្ លរំង៖ ● បិ ទ ប្ រ ព័ ន្ ធ និ ង ឧបករណ៍ េ្ ជា ប់ ទាំ ង អស់ ។ ● ផ្ តា ច់ ប្ រ ព័ ន្ ធ និ ង ឧបករណ៍ េ្ ជា ប់ ទាំ ង អស់ ដែលតេ្ ជា ប់ ពី ថា មពលអគ្ គិ ស ន
● កម្ រា លប្ រ ឆាំ ង នឹ ង ស្ តា ទិ ច – កម្ រា លប្ រ ឆាំ ង នឹ ង ស្ តា ទិ ច មានលក្ ខ ណៈឧណ្ ណាមាត្ រ និ ង គ្ លរំងបន្ ោ ស់ នា នាអាចដាក់ លលវាលៅលពលែំ លណរការលសវាកម្ ម ។ លៅលពលប្ ល រី ក ម្ រា លប្ រ ឆាំ ង នឹ ង ស្ តា ទិ ច ខ្ ដសពាក់ នឹ ង កនែរបស់ អ្ ន កគួ រ ដតមានភាពងាយស្ រួ ល លហយខ្ ដស ចងេ្ ជា ប់ គ្ នា គួ រ ដតេ្ ជា ប់ លៅកម្ រា ល និ ង លៅលោហៈមិ ន មានស្ លរាបលៅលលប្ រ ព័ ន្ ធ ដែលកំ ពុ ង ែំ លណរការ។ លៅលពលដែលត្ រូ ែ បានដាក់ ឱ្ យ បានត្ រឹ ម ត្ រូ ែ គ្ លរំងបន្ ោ ស់ ដែលត្ រូ ែ ធ្ ល ែី លសវាកម្ ម អាចត្ រូ ែ បានលដាះលចញពី កា បូ ប ESD ន
2 ការលដាះ និងការែំលឡងលឡងែិញ ប្រធានបទ : • • • • • • • • • • • • • • • • Recommended tools Screw List សមាសភាគសំ ខា ន់ ៗ ននប្ រ ព័ ន្ ធ របស់ អ្ ន ក គម្ រ បចំ លហ ង ស៊ុ ម ដគមខាងមុ ខ គ្ លរំងែំ លឡងែ្ រា យថាសរឹ ង ែ្ រា យស្ ថា នភាពរឹ ង គ្ លរំងែំ លឡងកង្ ហា រ កាត WLAN កន្ ដលងទទួ ល កំ លៅ ថ្ ម គ្ រា ប់ សំ ដបា ត មាូ ឌុ ល អង្ គ ចងចាំ ឧបាល័ រ មាូ ឌុ ល I/O ដែលជាជម្ ល រី ស (ប្ រ លេទ C/ HDMI/VGA/DP/Serial) អង្ គ ែំ លណរការ ផ្ ទាំ ង ប្ រ ព័ ន្ ធ Recommended tools The procedures in this document require the following tools: ●
Table 1. Screw list (continued) Component Screw type Quantity WLAN card M2x3.
សមាសភាគសំខាន់ៗននប្រព័ន្ធរបស់អ្នក 1.
2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. គ្ លរំងែំ លឡងកង្ ហា រ កន្ ដលងទទួ ល កំ លៅ ឧបាល័ រ ប្ រ អប់ ែ្ រា យថាសរឹ ង ផ្ ទាំ ង ប្ រ ព័ ន្ ធ តួ អង្ គ ែំ លណរការ M.2 WLAN មាូ ឌុ ល អង្ គ ចងចាំ ែ្ រា យស្ ថា នភាពរឹ ង M.
Steps 1. Loosen the thumbscrew (6x32) that secures the side cover to the system.
2. Slide the side cover towards the front of the system and lift the cover. Installing the side cover Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the side cover and provides a visual representation of the installation procedure.
Steps 1. Align the side cover with the grooves on the chassis. 2. Slide the side cover towards the back of the system to install it. 3. Tighten the thumbscrew (6x32) to secure the side cover to the system. Next steps 1. Follow the procedure in after working inside your computer. ស៊ុមដគមខាងមុខ ការលដាះស៊ុមខាងមុខ លសចក្ តី ត ម្ រូ ែ ជាមុ ន 1. អនុ ែ ត្ ត តាមែិ ធី លៅក្ នុ ង មុ ន នឹ ង ធ្ ល ែី កា រលៅខាងក្ នុ ង កុំ ព្ យូ ទ័ រ របស់ អ្ ន ក។ 2.
តំ ណា ក់ កា លទាំ ង ឡាយ 1. គាស់ លថបទប់ លំ នឹ ង លែម្ បី លដាះស៊ុ ម ខាងមុ ខ លចញពី ប្ រ ព័ ន្ ធ ។ 2.
តំ ណា ក់ កា លទាំ ង ឡាយ 1. ដាក់ ទី តាំ ង ស៊ុ ម លែម្ បី ត ម្ រ ង់ លថបជាមួ យ រន្ ធ លៅលលតួ ។ 2. ចុ ច សង្ ក ត់ ស៊ុ ម រហូ ត ែល់ លថបរំ លដាះចូ ល ស៊ ប់ លៅនឹ ង កន្ ដលង។ តំ ណា ក់ កា លបន្ ទា ប់ 1. ែំ លឡង គម្ រ បចំ លហ ង។ 2. អនុ ែ ត្ ត តាម ែិ ធី លៅក្ នុ ង បន្ ទា ប់ ពី ធ្ ល ែី កា រលៅខាងក្ នុ ង កុំ ព្ យូ ទ័ រ របស់ អ្ ន ក។ គ្លរំងែំលឡងែ្រាយថាសរឹង Removing the hard-drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover.
Steps 1. Press the release tabs on the hard-drive assembly and slide it towards the front of the system to disconnect it from the connector on the system board. 2. Lift the hard drive assembly from the system. NOTE: Note the orientation of the hard drive so that you can replace it correctly. Removing the hard-drive bracket Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the 2.5 in. hard-drive assembly.
Steps 1. Pull one side of the hard-drive bracket to disengage the pins on the bracket from the slots on the drive. 2. Lift the hard-drive out of the bracket. Installing the hard-drive bracket Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the hard-drive bracket and provides a visual representation of the installation procedure.
Steps 1. Place the hard-drive into the bracket. 2. Align and insert the pins on the drive bracket with the slots on the drive. NOTE: Note the orientation of the hard-drive so that you can replace it correctly. Next steps 1. Install the 2.5 in. hard-drive assembly. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. Installing the 2.5 in.
Steps 1. Insert the hard-drive assembly into the slot on the system. 2. Slide the hard-drive assembly towards the connector in the system board until the release tabs clicks into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. ែ្រាយស្ថានភាពរឹង Removing the M.2 2230 PCIe solid-state drive Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the hard-drive assembly.
About this task The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure. Steps 1. Remove the screw (M2x3.5) that secures the solid-state drive to the system board. 2. Slide and lift the solid-state drive off the system board. Installing the M.
Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive connector on the system board. 2. Insert the solid-state drive at a 45-degree angle into the solid-state drive connector. 3. Replace the screw (M2x3.5) that secures the M.2 2230 PCIe solid-state drive to the system board. Next steps 1. Install the hard-drive assembly. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. Removing the M.2 2280 PCIe solid-state drive Prerequisites 1.
Steps 1. Remove the screw (M2x3.5) that secures the solid-state drive to the system board. 2. Slide and lift the solid-state drive off the system board. Installing the M.2 2280 PCIe solid-state drive Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure.
Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive connector on the system board. 2. Insert the solid-state drive at a 45-degree angle into the solid-state drive connector. 3. Replace the screw (M2x3.5) that secures the M.2 2280 PCIe solid-state drive to the system board. Next steps 1. Install the hard-drive assembly. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. គ្លរំងែំលឡងកង្ហារ Removing the fan assembly Prerequisites 1.
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ 25
Steps 1. Unroute the speaker cable from the routing guide on the fan assembly. 2. Press the blue tabs on both sides of the fan, and slide to lift the fan to release it from the system. 3. Turn the fan assembly over. 4. Disconnect the fan cable from the connector on the system board. Lift the fan assembly out of the system.
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ 27
Steps 1. Connect the fan cable to the connector on the system board. 2. Turn the fan assembly over. 3. Press the release tab on the fan assembly and place it on the system until it clicks into place. 4. Route the speaker cable through the routing guides on the fan assembly. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. កាត WLAN Removing the WLAN card Prerequisites 1. Follow the procedure in before working inside your computer.
2. Remove the side cover. 3. Remove the hard-drive assembly. About this task The following images indicate the location of the wireless card and provide a visual representation of the removal procedure. Steps 1. Remove the (M2x3.5) screw that secures the WLAN card bracket to the system board. 2. Slide and lift the WLAN card bracket away from the WLAN card. 3. Disconnect the antenna cables from the WLAN card. 4. Slide and remove the WLAN card from the connector on the system board.
Steps 1. Connect the antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN card of your computer. Table 2. Antenna-cable color scheme Connectors on the wireless card Antenna-cable color Main (white triangle) White Auxiliary (black triangle) Black 2. Place the WLAN card bracket to secure the antenna cables. 3. Align the notch on the WLAN card with the tab on the WLAN card slot. Insert the WLAN card into the connector on the system board. 4.
កន្ដលងទទួលកំលៅ Removing the heat sink Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the fan assembly. About this task The following images indicate the location of the heat sink and provide a visual representation of the removal procedure. Steps 1. Loosen the three captive screws that secure the heat sink to the system. NOTE: Loosen the screw in the sequential order (1,2,3) as printed on the heat sink. 2.
Installing the heat sink Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the heat sink and provides a visual representation of the installation procedure. Steps 1. Align the screws of the heat sink with the holders on the system board and place the heat sink on the processor. 2. Tighten the captive screws that secure the heat sink to the system board.
ថ្មគ្រាប់សំដបាត Removing the coin-cell battery Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. NOTE: Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you note the BIOS setup program settings before removing the coin-cell battery. About this task The following images indicate the location of the coin-cell battery and provide a visual representation of the removal procedure. Steps 1.
Steps 1. Insert the coin cell battery with the "+" sign facing up and slide it under the securing tabs at the positive side of the connector. 2. Press the battery into the connector until it locks into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. មាូឌុលអង្គចងចាំ Removing the memory modules Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the fan assembly.
Steps 1. Pull the securing clips from the memory module until the memory module pops up. 2. Slide and remove the memory module from the memory-module slot. Installing the memory modules Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the memory modules and provides a visual representation of the installation procedure.
Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory module and reinstall it. Next steps 1. Install the fan assembly. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. ឧបាល័រ Removing the speaker Prerequisites 1.
Steps 1. Disconnect the speaker cable from the system board. 2. Press the release tab and lift the speaker along with the cable from the system board. Installing the speaker Prerequisites ប្ រ សិ ន លបអ្ ន កដាក់ ស មាសភាគចូ ល លដាះសមាសភាគដែលមានស្ រា ប់ លចញមុ ន ធ្ ល ែី កា រអនុ ែ ត្ ត ែិ ធី សា ស្ រ្ ត ក្ នុ ង ការែំ លឡង។ About this task The following image indicates the location of the speaker and provides a visual representation of the installation procedure.
Steps 1. Align and insert the speaker into the slot and press it until the release tab clicks. 2. Connect the speaker cable to the system board. Next steps 1. Install the fan assembly. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. មាូឌុល I/O ដែលជាជម្ល រីស (ប្រលេទ C/ HDMI/VGA/DP/Serial) Removing optional I/O modules (Type C/ HDMI/VGA/DP/Serial) Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover.
Installing optional I/O modules (Type C/ HDMI/VGA/DP/Serial) Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the system board and provide a visual representation of the installation procedure.
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ 41
Steps 1. To remove the dummy metal bracket, insert a flat-head screwdriver in the hole of the bracket. Push the bracket to release the bracket, and then lift the bracket out from the system. 2. Insert the optional I/O module (Type-C/HDMI/VGA/DP/Serial) into its slot from the inside of your computer. 3. Connect the I/O cable to the connector on the system board. 4. Replace the two (M3X3) screws to secure the optional I/O module to the system. Next steps 1. Install the side cover. 2.
2. Remove the side cover. 3. Remove the fan assembly. 4. Remove the heat sink. About this task The following images indicate the location of the processor and provide a visual representation of the removal procedure. Steps 1. Press down and push the release lever away from the processor to release it from the securing tab. 2. Lift the lever upward to lift the processor cover.
About this task The following image indicates the location of the processor and provides a visual representation of the installation procedure. Steps 1. Align the pin-1 corner of the processor with the pin 1 corner of the processor socket, and then place the processor in the processor socket. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height.
ផ្ទាំងប្រព័ន្ធ Removing the system board Prerequisites 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Follow the procedure in before working inside your computer. Remove the side cover. Remove the hard drive assembly. Remove the solid-state drive. Remove the WLAN card. Remove the fan assembly. Remove the heat sink. Remove the memory modules. Remove the speaker. Remove the optional IO module. Remove the processor.
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ
Steps 1. Remove the screw (6-32) that secures the hard drive caddy support to the system board. 2. Lift the hard drive caddy support away from the system board. 3. Remove the two (M3x4) screws and three (6-32) screws that secure the system board to the chassis. 4. Lift the system board away from the chassis. Installing the system board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
ការលដាះ និ ង ការែំ លឡងលឡងែិ ញ
Steps 1. Align and lower the system board into the system until the connectors at the back of the system board align with the slots on the chassis, and the screw holes on the system board align with the standoffs on the system. 2. Replace the two (M3x4) screws and three (6-32) screws to secure the system board to the chassis. 3. Align the slot on the hard drive caddy support with system board and place the hard drive caddy on the system board. 4.
3 ការលដាះស្រាយបញ្ហា ប្រធានបទ : • • • • • កម្ ម ែិ ធី ែិ និ ច្ ឆ័ យ ពិ និ ត្ យ ែំ លណរការប្ រ ព័ ន្ ធ មុ ន ប៊ូ ត របស់ Dell SupportAssist លក្ ខ ណៈេ្ លលង LED ែិ និ ច្ ឆ័ យ សារកំ ហុ ស ពី កា រែិ និ ច្ ឆ័ យ សារកំ ហុ ស ប្ រ ព័ ន្ ធ ែែ្ ត ថាមពល WiFi កម្ម ែិធី ែិនិច្ឆ័យពិនិត្យែំលណរការប្រព័ន្ធមុនប៊ូតរបស់ Dell SupportAssist អំ ពី កិ ច្ ច ការលនះ កម្ ម ែិ ធី លរាគែិ និ ច្ ឆ័ យ SupportAssist (ដែលស្ គា ល់ ថា ចាកម្ ម ែិ ធី លរាគែិ និ ច្ ឆ័ យ ប្ រ ព័ ន្ ធ )អនុ ែ ត្ ត ការត្ រួ ត ពិ និ ត្ យ លពញលលញននផ្ ដនករឹ ង របស់ អ្ ន ក។ កម្
លក្ខណៈេ្លលង LED ែិនិច្ឆ័យ តារាង 3.
តារាង 4.
តារាង 4.
តារាង 4. សារកំហុសពី ការែិនិច្ឆ័យ (បានបន្ ត ) សារបង្ ហា ញពី កំ ហុ ស បរិ យ៉ យ X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY បញ្ ចូ ល ឌី ស លៅក្ នុ ង ែ្ រា យែ៍ លហយព្ យ៉ យ៉មម្ ត ងលទ ត ។ សារកំហុសប្រព័ន្ធ តារាង 5. សារកំហុសប្ រព័ន្ធ សារប្ រ ព័ ន្ ធ បរិ យ៉ យ Alert! Previous attempts at booting this system have failed at checkpoint [nnnn].
4 ការទទួលយកជំនួយ ប្រធានបទ : • ការទំ នា ក់ ទំ ន ងមកក្ រុ ម ហ៊ុ ន Dell ការទំនាក់ទំនងមកក្រុមហ៊ុន Dell លសចក្ តី ត ម្ រូ ែ ជាមុ ន ចំ ណាំ : ប្ រ សិ ន លបអ្ ន កពុំ មា នអុី ន ធឺ ណិ ត សូ ម ស្ ដែងរកព័ ត៌ មា នទំ នា ក់ ទំ ន ងលលែិ ក្ ក យបត្ រ ជាែទំ និ ញ ប័ ណ្ ណលែចខ្ ច ប់ ែិ ក្ ក យបត្ រ ទូ ទា ត់ ប្ រា ក់ ឬ កាតាឡុ ក ផលិ ត ផល Dell ។ អំ ពី កិ ច្ ច ការលនះ Dell ផ្ ត ល់ ជ ម្ ល រី ស លសវាកម្ ម និ ង ការជំ នួ យ តាមទូ រ ស័ ព្ ទ និ ង អុី ន ធ័ រ ណិ ត ។ ជម្ ល រី ស លនះមានការប្ ដរប្ រួ ល តាមប្ រ លទស និ ង ផលិ ត ផល លហយលសវាកម្ ម ខ្ លះ ពុំ