Dell OptiPlex 5055 Tower Brukerhåndbok Forskriftsmessig modell: D18M Forskriftmessig type: D18M004
Merknader, forholdsregler og advarsler MERK: En merknad inneholder viktig informasjon som hjelper deg med å bruke ditt produkt mer effektivt. FORSIKTIG: En FORHOLDSREGEL angir enten potensiell fare for maskinvaren eller for tap av data og forteller hvordan du kan unngå problemet. ADVARSEL: En ADVARSEL angir potensiell fare for skade på eiendom, personskade eller død. © 2018 Dell Inc. eller dets datterselskaper. Med enerett. Dell og EMC og andre varemerker er varemerker for Dell Inc.
Innholdsfortegnelse 1 Arbeide på datamaskinen................................................................................................................................6 Sikkerhetsanvisninger........................................................................................................................................................ 6 Slå av datamaskinen..............................................................................................................................................
Fjerne innbruddsbryter...............................................................................................................................................31 Sette inn innbruddsbryteren...................................................................................................................................... 31 Strømbryter......................................................................................................................................................................
6 Feilsøking.................................................................................................................................................... 64 Enhanced Pre-Boot System Assessment – ePSA-diagnostikk..................................................................................
1 Arbeide på datamaskinen Sikkerhetsanvisninger Følg disse retningslinjene for sikkerhet for å verne om din egen sikkerhet og beskytte datamaskinen mot mulig skade. Med mindre annet er angitt, forutsetter hver av veiledningene i dette dokumentet følgende: • Du har lest sikkerhetsanvisningene som fulgte med datamaskinen. • En komponent kan byttes ut eller, dersom enheten kjøpes separat, settes inn ved at du utfører trinnene for demontering av komponenten i motsatt rekkefølge.
Før du arbeider inne i datamaskinen For å unngå å skade datamaskinen må du utføre trinnene nedenfor før du begynner å arbeide inne i datamaskinen. 1 Sørg for å overholde følgende sikkerhetsinstruksjoner. 2 Pass på at arbeidsunderlaget er plant og rent, slik at du unngår riper i datamaskindekselet. 3 Kontroller at du følger trinnene i Slå av datamaskinen. 4 Koble alle nettverkskabler fra datamaskinen.
2 Kabinett Kabinettet sett forfra 1 Strømknapp og strømlampe 2 Aktivitetslampe for harddisk 3 Minnekortleser (tilleggsutstyr) 4 optisk stasjon (tilleggsutstyr) 5 Hodesettport 6 USB 2.0-kontakt med PowerShare 7 USB 2.0-port 8 USB 3.
Kabinett sett bakfra – Radeon R7 A-serie APU 1 Linje-ut-port 2 DisplayPort 3 Seriell port 4 PS/2 tastatur-port 5 USB 3.1 Gen1-port 6 USB 2.
3 Ta ut og installere komponenter Denne delen gir detaljert informasjon om hvordan du kan fjerne og installere komponentene i datamaskinen. Anbefalte verktøy Prosedyrene i dette dokumentet kan kreve at du bruker følgende verktøy: • En liten skrutrekker med vanlig blad • Stjerneskrujern nr. 1 • Liten plasspiss Bakdeksel Ta av dekselet 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Slik løsner du dekselet: a b 10 Skyv den blå tappen for å løsne dekslet ut av datamaskinen [ 1].
3 Løft dekslet opp for å ta det av datamaskinen.
Sette på deksel 1 Sett dekselet på datamaskinen, og skyv dekselet framover til det klikker på plass. 2 Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Frontramme Ta av frontramme 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av dekslet. 3 Slik tar du av frontrammen: a b Løft tappene for å løsne rammen fra kabinettet [1]. Skyv rammen bort fra kabinettet [2]. MERK: Kontroller at tappene i bunnen av rammen også er løsnet før du løfter rammen.
4 Løft frontrammen opp for å fjerne den fra datamaskinen.
Montere frontramme 1 Plasser rammen slik at den er rettet inn etter tappeholderne på bunnen av kabinettrammen. 2 Trykk på rammen til tappene klikker på plass. 3 Sett på dekslet. 4 Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Frontpaneldøren Åpne frontpaneldøren 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme FORSIKTIG: Frontpaneldøren kan bare åpnes i begrenset grad. Bildet viser hvor mye frontpanelet kan åpnes.
Lagringsenhet Fjerne 3,5-tommers harddiskenhet 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b 3 deksel frontramme Slik fjerner du harddiskenheten: a Koble kablene til harddiskenheten fra kontaktene på harddisken.
MERK: Koble fra kablene fra klemmene fra harddiskrammen. b c 16 Skyv åpen frontpaneldøren. Fjern metallplaten.
d Trykk på den blå tappen [1] og trekk harddiskenheten ut av datamaskinen [2].
MERK: Tappen kan indikere 5,25 tommer fordi det er mulig å installere en 5,25 tommers harddisk i samme stasjonsbrønn. Fjerne 3,5-tommers harddisk fra harddiskbraketten 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b c 3 deksel frontramme harddiskenhet Slik fjerner du harddiskbraketten: a b 18 Trekk i den ene siden av harddiskbraketten for å frigjøre pinnene i braketten fra sporene på harddisken [1]. Løft harddisken ut av harddiskbraketten [2].
Sette inn 3,5-tommers harddisk i harddiskbraketten 1 Vri den andre siden av harddiskbraketten for å justere og sette inn pinnene på braketten i harddisken. 2 Skyv harddisken inn i harddiskbraketten til den klikker på plass. 3 Sett på plass: a b c 4 harddiskenhet frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Sette inn 3,5-tommers harddiskenhet 1 Skyv harddiskbraketten inn i sporet til den klikker på plass. 2 Plasser metallplaten.
Fjerne 2,5-tommers harddisk fra harddiskbraketten 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b c 3 deksel frontramme 2,5 tommers harddiskenhet Slik fjerner du harddiskbraketten: a b 20 Trekk i den ene siden av harddiskbraketten for å frigjøre pinnene i braketten fra sporene på harddisken [1]. Løft disken ut av diskbraketten [2].
Sette inn 2,5-tommers harddisk i harddiskbraketten 1 Vri den andre siden av harddiskbraketten for å justere og sette inn pinnene på braketten i harddisken. 2 Skyv harddisken inn i harddiskbraketten til den klikker på plass. 3 Sett på plass: a b c 4 2,5 tommers harddiskenhet frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Sette inn 2,5-tommers harddiskenhet 1 Skyv harddiskenheten inn i sporet i datamaskinen til den klikker på plass. 2 Lukk frontpaneldøren.
c 22 Trykk på den blå utløsertappen [1], og skyv den optiske stasjonen ut av datamaskinen [2].
Sette inn optisk stasjon 1 Sett den optiske stasjonen inn i stasjonsbrønnen til den klikker på plass. 2 Åpne frontpaneldøren. 3 Før datakabelen og strømkabelen under harddiskrammen. 4 Koble datakabelen og strømkabelen til baksiden av den optiske stasjonen. 5 Lukk frontpaneldøren. 6 Sett på plass: a b 7 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. M.2 PCIe SSD Fjerne valgfri M.2 PCIe SSD 1 Følg prosedyren i Før du arbeider inne i datamaskinen.
3 Fjern frontpaneldøren. 4 Slik tar du ut M.2 PCIe SSD: a b Trekk i den blå plasttappen som fester M.2 PCIe SSD til hovedkortet [1]. Koble M.2 PCIe SSD fra kontakten på hovedkortet [2]. Sette inn valgfri M.2 PCIe SSD 1 Sett inn M.2 PCIe SSD i kontakten 2 Trykk på den blå plastpinnen for å feste M.2 PCIe SSD. 3 Lukk frontpaneldøren. 4 Sett på plass: a b 5 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
SD-kort Ta ut SD-kortleseren 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme 3 Fjern frontpaneldøren. 4 Slik fjerner du SD-kortleseren: a b Koble kabelen for SD-kortleseren fra kontakten på hovedkortet [1]. Fjern skruen (6+/-1) som fester SD-kortleseren til frontpaneldøren [2]. c MERK: Skruen er plassert under SD-kortet. Løft SD-kortleseren ut av datamaskinen [3].
Sette inn SD-kortleser 1 Sett SD-kortleseren inn i sporet på hovedkortet. 2 Trekk til skruen (6+/-1) for å feste SD-kortleseren til frontpaneldøren. MERK: Skrueholderen er plassert under SD-kortleseren. 3 Koble kabelen til SD-kortleseren til kontakten på hovedkortet. 4 Lukk frontpaneldøren. 5 Sett på plass: a b 6 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Minnemoduler fjerne minnemodulen 1 Følg prosedyren i Før du arbeider inne i datamaskinen.
Utvidelseskort Ta ut PCIe-utvidelseskort 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme 3 Fjern frontpaneldøren. 4 Slik fjerner du PCIe-utvidelseskortet: a b Trekk til utløserlåsen for å løsne PCIe-utvidelseskort [1]. Skyv utløsertappen [2] og løft PCIe-utvidelseskort ut av datamaskinen [3]. MERK: Utløsertappen er plassert i bunnen av utvidelseskortet. 5 Gjenta trinnene for å ta ut eventuelle ekstra PCIe-utvidelseskort.
Sette inn PCIe-utvidelseskort 1 Dra utløseren bakover for å åpne. 2 Sett en skrutrekker inn i hullet til en PCIe-brakett, og skyv hardt for å løsne braketten [2]. Løft deretter braketten ut av datamaskinen. MERK: Hvis du vil fjerne PCIe-brakettene (2 og 4), skyver du braketten oppover fra innsiden av datamaskinen for å løsne den, og deretter løfter du braketten bort fra datamaskinen. 3 Sett PCIe-utvidelseskortet inn i kontakten på hovedkortet.
5 Slik fjerner du PSU: a Trykk på utløsertappen [1]. b MERK: Utløsertappen er plassert i bunnen av PSU Skyv og løft PSU bort fra datamaskinen [2].
Sette inn strømforsyningen – PSU 1 Sett strømforsyningsenheten inn i PSU-sporet, og skyv den mot baksiden av datamaskinen til den klikker på plass. 2 Stram til skruene (6+/-1) for å feste PSU til datamaskinen. 3 Før strømforsyningskablene gjennom festeklemmene. 4 Koble PSU-kablene til kontaktene på hovedkortet. 5 Lukk frontpaneldøren. 6 Sett på plass: a b 7 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
Fjerne innbruddsbryter 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme 3 Fjern frontpaneldøren. 4 Slik fjerner du innbruddsbryteren: a b c Koble kabelen til innbruddsbryteren fra kontakten på hovedkortet [1]. Trekk innbruddsbryterkabelen ut av kabelholderen. Skyv innbruddsbryteren og trykk på den for å fjerne den fra datamaskinen [2]. Sette inn innbruddsbryteren 1 Plasser Innbruddsbryteren i sporet i datamaskinen.
5 Sett på plass: a b 6 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Strømbryter Fjerne strømbryter 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme 3 Fjern frontpaneldøren. 4 Slik tar du ut strømbryteren: a b c d 5 Koble strømbryterkabelen fra hovedkortet [1]. Bruk en plastspiss til å fjerne kabelen til strømbryteren fra festeklemmen [2].
Sette inn strømbryter 1 Sett strømbryteren i sporet foran på datamaskinen, og trykk på den til den klikker på plass. 2 Juster kabelen etter pinnene på kontakten og koble til kabelen. 3 Lukk frontpaneldøren. 4 Sett på plass: a b 5 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Høyttaler Fjerne høyttaleren 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b 3 deksel frontramme Fjern frontpaneldøren.
4 Slik fjerner du høyttaleren: 34 a b Koble høyttalerkabelen fra kontakten på hovedkortet [1]. Lukk frontpaneldøren [2]. c Trykk ned utløsertappene [1], og skyv høyttalermodulen [2] ut av sporet.
Installere høyttaler 1 Sett høyttaleren inn i sporet. 2 Trykk høyttalermodulen inn til den låses på plass med et klikk. 3 Sett kontakten til høyttalerkabelen inn i kontakten på hovedkortet. 4 Lukk frontpaneldøren. 5 Sett på plass: a b 6 frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen. Klokkebatteri Ta ut klokkebatteri 1 Følg prosedyren i Før du arbeider inne i datamaskinen.
c utvidelseskort 3 Fjern frontpaneldøren. 4 Slik tar du ut klokkebatteriet: a b Bruk en plastspiss til å trykke på utløserlåsen til klokkebatteriet spretter ut [1]. Fjern klokkebatteriet fra kontakten på hovedkortet [2]. Sette inn klokkebatteriet 1 Hold batteriet slik at "+" vender opp, og skyv det under festetappene på den positive siden av kontakten. 2 Skyv batteriet inn i kontakten til det klikker på plass. 3 Lukk frontpaneldøren.
Varmeavlederenhet Ta ut varmeavlederenheten 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b deksel frontramme 3 Fjern frontpaneldøren. 4 Slik tar du ut varmeavlederenheten: a b Koble kabelen til varmelederenheten fra kontakten på hovedkortet [1]. Løsne festeskruene (6+/-1) som fester varmeavlederenheten til hovedkortet [2]. c MERK: Løsne skruene i henhold til tallene som vises på hovedkortet. Løft varmeavlederenheten ut av datamaskinen [3].
Sette inn varmeavlederenhet 1 Juster skruene på varmeavlederenheten etter holderne på hovedkortet. 2 Plasser varmelederenheten på prosessoren. 3 Skru inn igjen festeskruene (6+/-1) for å feste varmeavlederenheten til hovedkortet. MERK: Trekk til skruene i henhold til rekkefølgen oppgitt på hovedkortet. 4 Koble kabelen til varmelederenheten til kontakten på hovedkortet. 5 Lukk frontpaneldøren.
Sette inn prosessoren 1 Rett inne prosessoren med tappen på kontakten. FORSIKTIG: Du må ikke bruke kraft når du setter i prosessoren. Når prosessoren er korrekt plassert, er det enkelt å få den på plass i sokkelen. 2 Rett inn pinn-1 indikatoren på prosessoren med trekanten på kontakten. 3 Sett prosessoren på kontakten slik at sporet på prosessoren er på linje med tappene på kontakten. 4 Lukk prosessorlokket ved å skyve det under kortholderskruen.
Systemvifte Ta ut systemviften 1 Følg prosedyren i Før du arbeider inne i datamaskinen. 2 Ta av: a b c deksel frontramme innbruddsbryter 3 Åpne frontpaneldøren. 4 Slik tar du ut systemviften: a b c d 40 Koble systemviftekabelen fra kontakten på hovedkortet [1]. Fjern teipen som fester kabelen til innbruddsbryteren til systemviften, og flytt kabelen. Strekk ut gummipinnene som fester viften til datamaskinen for å forenkle fjerning av viften [2]. Skyv systemviften ut av datamaskinen [3].
Sette inn systemviften 1 Sett gummitetningene inn i sporene på kabinettrammen. 2 Hold systemviften med kabelen vendt mot bunnen av datamaskinen. 3 Rett inn sporene på systemviften etter gummitetningene på kabinettveggen. 4 Før de fire stroppene gjennom de tilsvarende sporene på systemviften. 5 Strekk ut stroppene, og skyv systemviften mot datamaskinen til den låses på plass. 6 Fest kabelen til innbruddsbryteren til systemviften med en selvklebende teip.
6 Koble følgende kabler fra hovedkortet: a b c d e f g 42 PSU [1] strømbryter [2] høyttaler [3] PSU [4] strømfordelingsenhet for optisk stasjon og harddisk [5] systemvifte [6] innbruddsbryter [7] Ta ut og installere komponenter
7 Slik tar du ut hovedkortet: a Skru ut skruene (6+/-1) som fester hovedkortet til datamaskinen Ta ut og installere komponenter 43
b 44 Skyv og løft hovedkortet bort fra datamaskinen [2].
Sette inn hovedkortet 1 Hold hovedkortet i kantene, og rett det inn mot baksiden av datamaskinen. 2 Senk hovedkortet inn i kabinettet til kontaktene på baksiden av hovedkortet er rettet inn etter sporene på kabinettet, og til skruehullene på hovedkortet er rettet inn etter avstandsholderne på datamaskinen. 3 Skru inn skruene (6+/-1) som fester hovedkortet til datamaskinen. 4 Før alle kablene gjennom kabelføringsklipsene.
7 Koble prosessorviftekabelen til kontakten på hovedkortet. 8 Lukk frontpaneldøren. 9 Sett på plass: a b c d e f 10 Lukk frontpaneldøren. a b 11 minnemodul valgfri M.2 PCIe SSD utvidelseskort SD-kortleser prosessor varmeavlederenhet frontramme deksel Følg fremgangsmåten i Etter at du har arbeidet inne i datamaskinen.
4 Teknologi og komponenter I dette kapittelet finner du informasjon om teknologien og komponentene som er tilgjengelig i systemet. Emner: • AMD PT B350 • AMD Radeon R7 M450 • AMD Radeon R5 M430 • USB-funksjoner • DDR4 AMD PT B350 AMD B350 • Brikkesett er perfekt for brukere som bruker mye kraft, og som setter pris på fleksibiliteten og overklokkingskontrollen, men som ikke trenger den maksimale PCIe-båndbredden som kreves ved konfigureringer med flere grafikkprosessorer.
AMD Radeon R7 M450 • Det første diagrammet viser den relative ytelsen til videokortet sammenlignet med 10 andre vanlige videokort med hensyn til PassMark G3D Mark. Nøkkelspesifikasjoner Følgende tabell inneholder nøkkelspesifikasjoner for AMD Radeon R7 M450: Tabell 2. Nøkkelspesifikasjoner Spesifikasjon AMD Radeon R7 M450 Produktserie AMD Støtte for API DirectX 12, OpenCL 1.2, OpenGL 4.3 Klokkehastighet 925 MHz Bussbredde 128-biters Minneklokkehastighet 1,125 GHz Teknologi DDR3 SDRAM Maks.
USB-funksjoner Universal Serial Bus, USB, ble lansert i 1996. Med USB ble det svært mye enklere å koble sammen vertsdatamaskiner og eksterne enheter mus, tastatur, eksterne drivere og skrivere. La oss ta en rask kikk på utviklingen av USB med henvisning til tabellen nedenfor. Tabell 4. USB-utvikling Type Dataoverføringshastighet Kategori Introduksjonsår USB 3.0 / USB 3.1 Gen 2 5 Gbps Superhastighet 2010 USB 2.0 480 Mbps Høy hastighet 2000 USB 3.1 Gen 1 (SuperSpeed USB) USB 2.
Med dagens stadig økende krav i forhold til dataoverføringer med HD-videoinnhold, terabyte-lagringsenheter, høyt antall megapiksler på digitale kameraer osv., er USB 2.0 kanskje ikke rask nok. Dessuten kan ingen USB 2.0-tilkobling noensinne komme i nærheten av den teoretisk maksimale gjennomstrømningen på 480 Mbps, som gir en dataoverføring på rundt 320 Mbps (40 MB/s) – som er faktisk reellt maksimum. På samme måten vil USB 3.1 Gen 1-tilkoblinger aldri oppnå 4,8 Gb/s.
Microsoft har annonsert at Windows 7 ville ha støtte for USB 3.1 Gen 1, kanskje ikke i den umiddelbare utgivelsen, men i en påfølgende servicepakke eller oppdatering. I etterkant av en vellykket lansering av støtte for USB 3.1 Gen 1 i Windows 7, er det ikke umulig å tenke seg at støtte for SuperSpeed også kommer til Vista. Microsoft har bekreftet dette ved å si at de fleste av partnerne deres er enige i at Vista også bør støtte USB 3.1 Gen 1. Super-Speed-støtte for Windows XP er for øyeblikket ukjent.
Figur 3. Avrundet kant Minnefeil Minnefeil på systemet vises med den nye feilkoden PÅ-BLINK-BLINK eller PÅ-BLINK-PÅ. Ved total minnesvikt slår ikke LCD-en seg på. Foreta søk etter mulige minnefeil ved å prøve kjente, gode minnemoduler i minnekontaktene på undersiden av systemet, eller under tastaturet, som i enkelte bærbare systemer.
5 Systemoppsett Systemoppsettet gir deg muligheten til å administrere stasjonær PC- maskinvare og spesifisere BIOS-alternativer.
Tabell 5. Generelt Alternativ Beskrivelse System Information Viser følgende informasjon: • • • • • Boot Sequence • • • • Advanced Boot Options Enabled (Aktivert) (valgt som standard) Disabled (Deaktivert) Lar deg velge BIOS Setup Advanced Mode (Avansert modus for BIOS-oppsett). Dette alternativet er valgt som standard.
Alternativ Beskrivelse MERK: Avhengig av datamaskinen og enhetene som er installert, er det mulig at noen av elementene i denne listen ikke vises. Serial Port Alternativene er: • • • • SATA Operation Med dette alternativet kan du konfigurere driftsmodusen til den integrerte harddiskkontrolleren.
Tabell 7. Skjermkort Alternativ Beskrivelse Multi-Display Dette alternativet er valgt som standard. Primary Display Her kan du velge den primære skjermen når flere skjermer er tilgjengelig i systemet. • • Auto (standard) Integrated Graphics MERK: Hvis du ikke velger Auto vil det innebygde skjermkortet være til stede og aktivert. Tabell 8. Security (Sikkerhet) Alternativ Beskrivelse Admin Password Her kan du angi, endre eller slette administratorpassordet.
Alternativ Beskrivelse • • Chassis Intrusion Disable (Deaktiver) Activate (Aktiver) Alternativene er: • • • Admin Setup Lockout Deaktiver (standard) Enable (Aktiver) On-Silent (Lydløs) Her kan du aktivere eller deaktivere alternativet for å gå inn i oppsettet når et administratorpassord er valgt. Dette alternativet er ikke angitt som standard. Tabell 9.
Tabell 11. Strømadministrasjon Alternativ Beskrivelse AC Recovery Fastslår hvordan systemet reagerer når nettstrøm blir slått på igjen etter et strømtap. Du kan sette AC Recovery til: • • • Power Off (Slå av) Power On (Slå på) Last Power State (Siste strømtilstand) Strømmen er slått av som standard. Auto On Time Angir at maskinen skal startes automatisk på et bestemt tidspunkt. Tidsinnstillingen bruker standard 12-timers format (timer:minutter:sekunder).
Alternativ Beskrivelse • • Extend BIOS POST Time Alternativene er: • • • Full Screen Logo Continue on Warnings (Fortsett med advarsler) Continue on Warnings and Errors (Fortsett ved advarsler og feil) 0 seconds (0 sekunder) (Standard) 5 seconds (5 sekunder) 10 seconds (10 sekunder) Dette alternativet er deaktivert som standard. Tabell 13. Virtualiseringsstøtte Alternativ Beskrivelse AMD-V Technology (AMD-Vteknologi) Dette alternativet er aktivert som standard.
Tabell 16. SupportAssist System Resolution (systemoppløsningen for SupportAssist) Alternativ Beskrivelse Auto OS Recovery Threshold Alternativene er: AV, 1, 2 (standard), 3. Spesifikasjoner MERK: Tilbudene kan variere etter region. Du finner mer informasjon om hvordan du konfigurerer datamaskinen her: • Windows 10: Klikk eller trykk raskt på Start > Innstillinger > System > Om. Tabell 17. Brikkesett Funksjon Spesifikasjon Brikkesett AMD B350-brikkesett Tabell 18.
Tabell 22. Ekspansjonsbuss Funksjon Spesifikasjon Busstype USB 2.0, USB 3.1 Gen 1, SATA 3 og PCle opptil Gen 3 Busshastighet • • • • USB 2.0 – 480 Mbps USB 3.1 Gen 1 – 5 Gb/s SATA 3.0 – 6 Gbps PCIe – 8 Gbps Tabell 23. Kort Funksjon Spesifikasjon WLAN-kort • • • Intel Wireless – AC 8265 2 x 2 Intel Wireless – AC 3165 1 x 1 Bluetooth 4.1 MERK: For å få optimal ytelse anbefales det at funksjonen med trådløs display brukes med et tilgangspunkt som støtter 5 GHz standard. Tabell 24.
Funksjon Spesifikasjon • DisplayPort 1.2 (tilleggsutstyr 2*DP som bare har støtte for APU i Aserien) MERK: Tilgjengelige videokontakter kan variere avhengig av grafikkortet som velges. Tabell 26. Kontroller og lamper Funksjon Spesifikasjon Maskinen sett forfra Strømknapplys Hvitt lys — Fast hvitt lys indikerer at datamaskinen er på. Sakte blinkende hvitt lys indikerer at datamaskinen er i ventemodus.
Fysiske dimensjoner Tårn Vekt 7,93 kg (17,49 pund) Tabell 29. Omgivelser Funksjon Spesifikasjon Temperaturområde Ved bruk 5 °C til 35 °C (41 °F til 95 °F) Ikke i bruk –40 °C til 65 °C (–40 °F til 149 °F) Relativ fuktighet (maks.
6 Feilsøking Enhanced Pre-Boot System Assessment – ePSAdiagnostikk ePSA-diagnostikk (også kjent som systemdiagnostikk) utfører en komplett kontroll av maskinvaren. ePSA er innebygd i BIOS, og startes internt av BIOS.