OptiPlex 7040 - 小型计算机 用户手册 管制型号: D11S 管制类型: D11S001
注、小心和警告 注: “注”表示可以帮助您更好地使用计算机的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并说明如何避免此类问题。 警告: “警告”表示可能会造成财产损失、人身伤害甚至死亡。 版权所有 © 2015 Dell Inc. 保留所有权利。 本产品受美国、国际版权和知识产权法律保护。 Dell™ 和 Dell 徽标是 Dell Inc. 在美国和 / 或其他管辖区域的商标。所有此处提及的其他商标和产品名称可能是其各自所属公司的商标。 2015 - 11 Rev.
目录 1 拆装计算机内部组件............................................................................................... 5 拆装计算机内部组件之前........................................................................................................................5 关闭计算机............................................................................................................................................. 6 拆装计算机内部组件之后...........................................................................................................
卸下 SD 卡读取器.................................................................................................................................22 安装 SD 卡读取器................................................................................................................................. 23 安装可选 SSD 卡...................................................................................................................................23 卸下可选 SSD 卡.........................................................................
1 拆装计算机内部组件 拆装计算机内部组件之前 遵循以下安全原则有助于防止您的计算机受到潜在损坏,并有助于确保您的人身安全。除非另有说明,否则在 执行本说明文件中所述的每个步骤前,都要确保满足以下条件: • 已经阅读了计算机附带的安全信息。 • 以相反顺序执行拆卸步骤可以更换组件或安装单独购买的组件。 警告: 打开主机盖或面板前切断所有电源。执行完计算机组件拆装工作后,装回所有护盖、面板和螺钉后 再连接电源。 警告: 拆装计算机内部组件之前,请阅读计算机附带的安全信息。有关安全最佳实践的其他信息,请参阅 www.Dell.
关闭计算机 小心: 为避免数据丢失,请在关闭计算机之前,保存并关闭所有打开的文件,并退出所有打开的程序。 1. 关闭计算机: • • • • 2. 在 Windows 10 中(使用支持触控的设备或鼠标): 1. 单击或点按 2. 单击或点按 。 然后单击或轻触关机。 在 Windows 8 中(使用支持触控的设备): 1. 从屏幕右边缘滑动,打开 Charms 菜单,然后选择设置。 2. 点按 然后点按关机 在 Windows 8 中(使用鼠标): 1. 指向屏幕的右上角,然后单击设置。 2. 单击 然后单击关机。 在 Windows 7 中: 1. 单击 Start(开始)。 2. 单击关机。 确保计算机和所有连接的设备的电源均已关闭。如果关闭操作系统时,计算机和连接的设备的电源未自动 关闭,请按住电源按钮大约 6 秒钟即可将它们关闭。 拆装计算机内部组件之后 完成所有更换步骤后,请确保在打开计算机前已连接好所有外部设备、插卡和电缆。 1. 装回主机盖。 小心: 要连接网络电缆,请先将电缆插入网络设备,然后将其插入计算机。 2.
2 卸下和安装组件 此部分提供如何从计算机中卸下或安装组件的详细信息。 建议工具 执行本说明文件中的步骤时可能需要使用以下工具: • 小型平口螺丝刀 • 梅花槽螺丝刀 • 小型塑料划片 卸下护盖 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下护盖: a. 将蓝色固定卡舌滑至右侧以解锁护盖 [1]。 b. 朝计算机背面滑动护盖 [2]。 c.
安装护盖 1. 将主机盖放在计算机上,然后滑动主机盖直至卡入到位。 2. 按照“拆装计算机内部组件之后”中的步骤进行操作 卸下前挡板 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下主机盖。 3. 卸下前挡板: a. 提起卡舌以从计算机中释放前挡板 [1]。 b. 从计算机上卸下前挡板 [2]。 安装前挡板 1. 将挡板上的卡舌插入计算机上的插槽中。 2. 按压挡板直至卡舌卡入到位。 3. 安装主机盖。 4. 按照“拆装计算机内部组件之后”中的步骤进行操作 卸下风扇导风管 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下主机盖。 3. 要卸下系统风扇: a. 握住触点,拉动风扇导风管支架以释放风扇导风管 [1]。 b.
安装风扇导风管 1. 将风扇导风管上的插槽与散热器上的螺钉对齐。 2. 将风扇导风管插入直至其卡入到位。 3. 安装主机盖。 4. 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下内存模块 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. 3. 主机盖 风扇导风管 硬盘驱动器部件 光盘驱动器 要卸下内存模块: a. 按下内存模块两侧的内存模块固定卡舌。 b.
安装内存模块 1. 将内存模块上的槽口与内存模块连接器上的卡舌对齐。 2. 将内存模块插入内存模块插槽。 3. 按下内存模块,直到内存模块的固定卡舌卡入到位。 4. 安装以下组件: a. b. c. d. 5. 光盘驱动器 硬盘驱动器部件 风扇导风管 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下防盗开关 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 主机盖 b. 风扇导风管 3. 要卸下防盗开关: a. 断开防盗开关电缆与系统板上的连接器的连接 [1][2]。 b. 滑动防盗开关,然后将其提离计算机 [3]。 安装防盗开关 1. 将防盗开关插入机箱上的插槽中。 2. 将防盗开关电缆连接到系统板。 3. 安装以下组件: a. 风扇导风管 b. 主机盖 4.
卸下扩充卡 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 主机盖 b. 风扇导风管 3. 要卸下扩充卡: a. 拉动金属卡舌以释放扩充卡闩锁 [1]。 b. 向前推动卡舌 [2],然后从计算机上的连接器拉出扩充卡 [3]。 安装扩充卡 1. 将扩充卡插入系统板上的连接器。 2. 按压扩充卡,直至其卡入到位。 3. 关闭扩充卡闩锁,然后将其按下,直至卡入到位。 4. 安装以下组件: a. 风扇导风管 b. 主机盖 5. 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下硬盘驱动器部件 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 主机盖 b. 风扇导风管 3. 要卸下硬盘驱动器部件: a. 推动固定卡舌,然后卸下电源连接器 [1、2]。 b.
4. 卸下硬盘驱动器部件: a. 向前拉动硬盘驱动器释放手柄,将硬盘驱动器支架从计算机中卸下 [1]。 b. 将硬盘驱动器部件提离计算机 [2]。 将硬盘驱动器从硬盘驱动器支架卸下 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 护盖 b. 挡板 c. 硬盘驱动器部件 3. 要卸下硬盘驱动器支架: a. 拉动硬盘驱动器支架,以释放硬盘驱动器 [1]。 b.
将硬盘驱动器安装到硬盘驱动器支架中 1. 将硬盘驱动器插入硬盘驱动器支架,直至其卡入到位。 2. 安装以下组件: a. 硬盘驱动器部件 b. 挡板 c. 护盖 3. 按照“拆装计算机内部组件之后”中的步骤进行操作。 安装硬盘驱动器部件 1. 将硬盘驱动器部件插入计算机上的插槽。 2. 将电源电缆连接至硬盘驱动器支架上的插槽。 3. 安装以下组件: a. 风扇导风管 b. 主机盖 4. 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下光盘驱动器 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 主机盖 b. 前挡板 c. 硬盘驱动器部件 3. 要释放光盘驱动器: a. 从光盘驱动器闩锁卸下硬盘驱动器连接器电缆 [1]。 b.
4. 要卸下光盘驱动器: a. 握住蓝色闩锁 [1],提起光盘驱动器固定框架,然后断开电缆与光盘驱动器的连接 [2]。 b. 将光盘驱动器固定框架提离计算机 [3]。 5. 要将光盘驱动器从光盘驱动器固定框架中卸下: a. 按下光盘驱动器释放闩锁 [1],然后将光盘驱动器向前滑动 [2]。 b.
安装光盘驱动器 1. 将光盘驱动器滑入光盘驱动器固定框架。 2. 将光盘驱动器固定框架上的卡舌与计算机上的插槽对齐。 3. 将光盘驱动器固定框架放入计算机中并锁定闩锁。 4. 将数据电缆和电源电缆连接至光盘驱动器。 5. 安装以下组件: a. 硬盘驱动器部件 b. 前挡板 c. 主机盖 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下系统风扇 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. 3. 主机盖 前挡板 硬盘驱动器部件 光盘驱动器 要卸下系统风扇: a. 断开系统风扇电缆与系统板的连接 [1]。 b. 朝后壁上的插槽滑动风扇索环 [2]。 c.
安装系统风扇 1. 将系统风扇置于计算机中。 2. 将索环穿过机箱,然后沿插槽向外滑动使其卡入到位。 3. 将系统风扇电缆连接至系统板。 4. 安装以下组件: a. b. c. d. 5. 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下散热器部件 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 3. 主机盖 前挡板 风扇导风管 硬盘驱动器部件 光盘驱动器 卸下散热器部件: a. 断开散热器电缆与系统板的连接 [1]。 b.
安装散热器部件 1. 将散热器部件放在处理器上。 2. 拧紧用于将散热器部件固定至系统板的固定螺钉。 3. 将散热器电缆连接至系统板。 4. 安装以下组件: a. b. c. d. e. 5. 风扇导风管 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下处理器 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. f. 3. 主机盖 前挡板 硬盘驱动器部件 光盘驱动器 风扇导风管 散热器 卸下处理器: a. 通过从处理器护盖上的卡舌下方向下并向外按压拉杆释放插槽拉杆。 b. 向上提起拉杆,然后提起处理器护盖 [2]。 c.
安装处理器 1. 将处理器与插槽卡锁对齐。 2. 将处理器的插针 1 标志与插槽上的三角形对齐。 3. 将处理器放置在插槽上,从而使处理器上的插槽与插槽卡锁对齐。 4. 将处理器护盖滑到固定螺钉下方,以合上处理器护盖。 5. 放下插槽拉杆并将其推到卡舌下方以将其锁定。 6. 安装以下组件: a. b. c. d. e. f. 7. 散热器 风扇导风管 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下 VGA 子板 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. 主机盖 b. 风扇导风管 3. 要卸下 VGA 子板: a. b. c. d.
安装 VGA 子板 1. 将 VGA 子板与系统板上的螺钉固定器对齐。 2. 拧紧将 VGA 子板固定至系统板的螺钉。 3. 将 VGA 连接器插入计算机背面的插槽。 4. 拧紧将 VGA 连接器固定至计算机的螺钉。 5. 安装以下组件: a. 风扇导风管 b. 主机盖 6. 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下电源设备 (PSU) 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 3. 主机盖 前挡板 硬盘驱动器部件 光盘驱动器 风扇导风管 要释放 PSU: a. 断开电源电缆与系统板的连接 [1] [2]。 b.
4. 卸下 PSU: a. 断开电源电缆与系统板的连接 [1] [2]。 b. 将电缆提离计算机 [3]。 c. 拧下将 PSU 固定至计算机的螺钉 [4]。 5.
安装电源设备 (PSU) 1. 将 PSU 插入机箱,然后将其朝计算机背面滑动以固定。 2. 拧紧将 PSU 固定至计算机背面的螺钉。 3. 通过固定夹布置 PSU 电缆的连接。 4. 将电源电缆连接至系统板。 5. 安装以下组件: a. b. c. d. e. 6. 风扇导风管 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下电源开关 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 3. 主机盖 前挡板 硬盘驱动器部件 光盘驱动器 电源设备 卸下电源开关: a. 断开电源开关电缆与系统板的连接 [1]。 b.
安装电源开关 1. 将电源开关模块滑入机箱上的插槽,直至其卡入到位。 2. 将电源开关电缆连接至系统板上的连接器。 3. 安装以下组件: a. b. c. d. e. 4. 电源设备 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 卸下 SD 卡读取器 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. 3. 主机盖 前挡板 硬盘驱动器部件 光盘驱动器 电源设备 要卸下 SD 卡读取器: a. 从 SD 卡读取器外壳上的固定夹中抽出电源设备电缆 [1]。 b.
安装 SD 卡读取器 1. 将 SD 卡读取器放在机箱上。 2. 拧紧将 SD 卡读取器固定到计算机的螺钉。 3. 将电源设备电缆穿入固定夹。 4. 安装以下组件: a. b. c. d. e. 5. 电源设备 光盘驱动器 硬盘驱动器部件 前挡板 主机盖 按照“拆装计算机内部组件之后”中的步骤进行操作。 安装可选 SSD 卡 1. 卸下以下组件: a. 主机盖 b. 前挡板 2.
3. 将橡胶垫放在计算机上 [1],然后从橡胶垫剥下粉色胶带 [2]。 4. 要安装 SSD 卡: a. 将 SSD 卡连接至系统板上的连接器 [1]。 b.
卸下可选 SSD 卡 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: • 护盖 • 前挡板 3. 拧下将 SSD 卡固定至系统板的螺钉。 4. 断开 SSD 卡与系统板上的连接器的连接。 5. 将橡胶垫从系统板卸下。 卸下系统板 1. 按照“拆装计算机内部组件之前”中的步骤进行操作。 2. 卸下以下组件: a. b. c. d. e. f. g. h. i. j. k. l. 3. 主机盖 风扇导风管 前挡板 内存模块 硬盘驱动器部件 光盘驱动器 扩展卡 可选 SSD 卡 SD 卡读取器 VGA 子板 散热器 处理器 要卸下 I/O 面板,请执行下列操作: a. 拧下将 I/O 面板固定到机箱的螺钉 [1]。 b.
4. 断开连接到系统板的所有电缆。 5. 要卸下系统板: a. 拧下用于将系统板固定至计算机的螺钉 [1]。 b.
安装系统板 1. 握住系统板边缘,并朝计算机背面调整其角度。 2. 将系统板向下放入计算机,直至系统板背面的连接器与计算机后壁上的插槽对齐,且系统板上的螺孔与计 算机上的定位器对齐。 3. 拧紧将系统板固定至计算机的螺钉。 4. 将电缆连接至系统板。 5. 安装以下组件: a. b. c. d. e. f. g. h. i. j. k. l. VGA 子板 SD 卡读取器 可选 SSD 卡 扩展卡 处理器 散热器 光盘驱动器 硬盘驱动器部件 内存模块 前挡板 风扇导风管 主机盖 6. 将 I/O 面板放在机箱上。 7. 拧紧将 I/O 面板固定到机箱的螺钉。 8.
系统板布局 1. PCIex16 连接器 2. PCIex4 连接器 3. RJ-45/USB 2.0 连接器 4. USB 3.0 连接器 5. PS2 键盘/MS 连接器 6. 串行端口连接器 7. DisplayPort 连接器 8. HDMI 连接器 9. 输出连接器 10. CPU 电源连接器 11. 防盗开关连接器 12. VGA 子板连接器 13. 处理器 14. CPU 风扇连接器 15. 内存模块连接器 16. M.2 插槽 3 连接器 17. 电源开关连接器 18. 介质卡读取器连接器 19. 系统风扇连接器 20. 硬盘驱动器活动 LED 21. 通用音频插孔 22. USB 2.0 连接器 23. USB 3.0 连接器 24. ATX 电源连接器 25. SATA2 连接器 26. SATA0 连接器 27. 内置扬声器连接器 28.
. 内部 USB 连接器 31. 币形电池 30.
3 排除计算机故障 在计算机运行期间,可以利用诊断指示灯、哔声代码和错误消息排除计算机故障。 诊断电源 LED 代码 表.
诊断错误消息 表.
错误消息 说明 HARD-DISK DRIVE CONFIGURATION ERROR(硬 盘驱动器配置错误) 计算机无法识别驱动器的类型。关闭计算机,卸下硬 盘驱动器,并从光盘驱动器引导计算机。然后关闭计 算机,重新安装硬盘驱动器,并重新启动计算机。请 运行 Dell Diagnostics 中的 Hard Disk Drive(硬盘 驱动器)检测程序。 HARD-DISK DRIVE CONTROLLER FAILURE 0 (硬盘驱动器控制器故障 0) 硬盘驱动器不响应来自计算机的命令。关闭计算机, 卸下硬盘驱动器,并从光盘驱动器引导计算机。然后 关闭计算机,重新安装硬盘驱动器,并重新启动计算 机。如果问题仍然存在,请尝试使用其他驱动器。请 运行 Dell Diagnostics 中的 Hard Disk Drive(硬盘 驱动器)检测程序。 HARD-DISK DRIVE FAILURE(硬盘驱动器故障) 硬盘驱动器不响应来自计算机的命令。关闭计算机, 卸下硬盘驱动器,并从光盘驱动器引导计算机。然后 关闭计算机,重新安装硬盘驱动器,并重新启动计算 机。如果问题仍然存在,请尝试使用其他驱动
错误消息 说明 LICENSED CONTENT IS NOT ACCESSIBLE IN Dell MediaDirect 无法验证针对该文件的数字权限管 MEDIADIRECT(无法在 MediaDirect 中访问许可 理 (DRM) 限制,因此无法播放该文件。 内容) MEMORY ADDRESS LINE FAILURE AT ADDRESS, 内存模块可能出现故障或未正确插接。重新安装内存 READ VALUE EXPECTING VALUE(寻址、读取所 模块,如果有必要,请更换内存模块。 需的值时,内存地址线路出现故障) MEMORY ALLOCATION ERROR(内存分配错误) 要运行的软件与操作系统、其他程序或公用程序发生 冲突。关闭计算机并等待 30 秒钟,然后重新启动计 算机。再次尝试运行此程序。如果仍然显示此错误消 息,请参阅软件说明文件。 MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE(寻 址、读取所需的值时,内存双字逻辑出现故障) 内存模块可能出现故障或未正确插接。重新安
错误消息 说明 故障,请备份数据(如果可能),然后重新格式化硬 盘驱动器。 SEEK ERROR(寻道错误) 操作系统无法找到硬盘驱动器上的特定磁道。 SHUTDOWN FAILURE(关机故障) 可能是系统板上的芯片出现故障。请运行 Dell Diagnostics 中的 System Set(系统设定)检测程 序。如果再次出现此错误信息,请与 Dell 联络。 TIME-OF-DAY CLOCK LOST POWER(计时时钟电 源中断) 系统配置设置已损坏。将计算机连接至电源插座,为 电池充电。如果问题仍然存在,请进入系统设置程序 尝试恢复数据,然后立即退出程序。如果再次出现此 错误信息,请与 Dell 联络。 TIME-OF-DAY CLOCK STOPPED(计时时钟停止) 支持系统配置设置的备用电池可能需要重新充电。将 计算机连接至电源插座,为电池充电。如果问题仍然 存在,请与 Dell 联络。 TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM SETUP PROGRAM(未设置计时 - 请运行 系统设置程序) 系统设置程序中存储的时间或日期
系统消息 说明 CPU fan failure(CPU 风扇故障) CPU 风扇出现故障。 System fan failure(系统风扇故障) 系统风扇出现故障。 Hard-disk drive failure(硬盘驱动器出现故 障) 硬盘驱动器可能在开机自测过程中出现故障。 Keyboard failure(键盘故障) 键盘出现故障或电缆松动。如果重新拔插电缆不能解 决问题,请更换键盘 No boot device available(无可用的引导设 备) 硬盘驱动器上无可引导分区,或硬盘驱动器电缆松 动,或不存在可引导设备。 • • No timer tick interrupt(无计时器嘀嗒信号 中断) 如果将硬盘驱动器用作引导设备,请确保电缆已 连接,并且驱动器已正确安装并已分区,可以用 作引导设备。 进入系统设置程序,确保引导顺序信息正确。 系统板上的芯片可能发生故障或母板出现故障。 NOTICE - Hard Drive SELF MONITORING S.M.A.R.
4 系统设置程序 可通过系统设置程序管理计算机硬件和指定 BIOS 级选项。可以在系统设置程序中完成以下操作: • 在添加或删除硬件后更改 NVRAM 设置 • 查看系统硬件配置 • 启用或禁用集成设备 • 设置性能和电源管理阈值 • 管理计算机安全保护 Boot Sequence 引导顺序允许您略过系统设置程序 — 定义的引导设备顺序和直接引导至特定的设备(例如:光盘驱动器或硬 盘驱动器)。开机自检 (POST) 期间,出现 Dell 徽标时,您可以: • 按下 F2 键访问系统设置程序 • 按下 F12 键显示一次性引导菜单 一次性引导菜将显示您可以从中引导的设备,包括诊断选项。引导菜单选项包括: • Removable Drive(可移动驱动器)(如果可用) • STXXXX Drive(STXXXX 驱动器) 注: XXX 表示 SATA 驱动器号 • 光盘驱动器 • 诊断程序 注: 选择 Diagnostics(诊断程序)将显示 ePSA diagnostics(ePSA 诊断程序)屏幕。 引导顺序屏幕还会显示访问 System Setup(系统设置程序)
键 导航 Enter 键 允许您在所选字段(如适用)中选择值或单击字段中的链接。 空格键 展开或折叠下拉列表(如适用)。 选项卡 移到下一个目标区域。 注: 仅适用于标准图形浏览器。 Esc 键 移至上一页直到您看到主屏幕。在主屏幕中按 Esc 将显示一则消息,提示您保存任何未 保存的更改并重新启动系统。 F1 显示系统设置程序的帮助文件。 系统设置程序概览 通过系统设置程序,您可以: • 在您的计算机中添加、更改或卸下任何硬件之后更改系统配置信息。 • 设置或更改用户可选择的选项(例如用户密码)。 • 读取当前内存容量或设置已安装的硬盘驱动器的类型。 使用系统设置程序之前,建议您记下系统设置程序屏幕信息,以备将来参考。 小心: 除非您是高级计算机用户,否则请勿更改系统设置程序的设置。某些更改可能会导致计算机运行不 正常。 访问系统设置程序 1. 打开(或重新启动)计算机。 2.
选项 说明 • • • Boot Sequence Memory Channel Mode(内存通道模式)、Memory Technology(内存 技术)、DIMM 1 Size(DIMM 1 大小)、DIMM 2 Size(DIMM 2 大小)、 DIMM 3 Size(DIMM 3 大小)以及 DIMM 4 Size(DIMM 4 大小)。 PCI Information(PCI 信息):显示 SLOT1、SLOT2、SLOT3、SLOT4 和 SLOT5_M.
选项 说明 • Drives 允许您启用或禁用系统板上的各个驱动器: • • • Smart Reporting USB Configuration RAID ON = 将 SATA 配置为支持 RAID 模式 SATA-0 SATA-1 SATA-2 该字段控制是否在系统启动过程中报告集成驱动器的硬盘错误。 允许您为以下选项启用或禁用集成 USB 控制器: • • • Enable Boot Support(启用引导支持) Enable Rear Quad USB(启用前置四个 USB) Enable Rear USB Ports(启用后置 USB 端口) 默认情况下启用所有选项。 Front USB Configuration 允许您启用或禁用前置 USB 端口。所有端口在默认设置下已启用。 Back USB Configuration 允许您启用或禁用后置 USB 端口。所有端口在默认设置下已启用。 USB PowerShare 此选项允许您对外部设备进行充电,如移动电话、音乐播放器。此选项在默认 设置下已禁用。 Audio 允许您启用或禁用集成音频控制器。 • • E
选项 说明 Internal HDD-0 Password 允许您设置、更改和删除计算机的内部 HDD。 Internal HDD-0 Password 允许您设置、更改和删除计算机的内部 HDD。 Strong Password 该选项使您启用或禁用系统的增强密码。 Password Configuration 允许您控制管理密码和系统密码所允许的最小和最大字符数。 Password Bypass 使用该选项,可以在重新启动系统时略过系统(引导)密码和内置 HDD 密码。 • • Disabled(已禁用)— 当设置系统和内置 HDD 密码后,始终提示输入密 码。此选项在默认设置下已禁用。 Reboot Bypass(重新引导时略过) — 略过重新启动(热启动)的密码提 示。 注: 从关机状态启动系统(冷启动)时,系统始终提示输入系统和内置 HDD 密码。系统还将始终在可能出现的任何模块化 HDD 上提示输入密 码。 Password Change 此选项允许您在设置管理员密码时决定是否允许更改系统和硬盘密码。 Allow Non-Admin Password Changes(允许非管理
选项 说明 该选项的默认设置为 Enable(启用)。 Admin Setup Lockout 允许您在设置管理密码后启用或禁用进入设置选项。此选项默认未设置。 HDD Protection Support 允许您启用或禁用 HDD Protection(HDD 保护)功能。此选项是高级功能, 旨在保证 HDD 数据安全和不可更改。此选项在默认设置下已禁用。 表.
表. 11: Performance(性能) 选项 说明 Multi Core Support 该字段指定该程序是否有一个或多核心已启用。此选项在默认设置下已启用。 Intel SpeedStep 允许您启用或禁用处理器的 Intel SpeedStep 模式。此选项在默认设置下已禁 用。 C States Control 允许您启用或禁用其他处理器睡眠状态。此选项在默认设置下已禁用。 Limited CPUID Value 允许您限制处理器标准 CPUID 功能的最大值。此选项在默认设置下已禁用。 Intel TurboBoost 允许您启用或禁用处理器的 Intel TurboBoost 模式。此选项在默认设置下已启 用。 HyperThread control 允许您启用或禁用处理器的超线程。 表.
选项 说明 Block Sleep 允许您阻止在操作系统环境中进入睡眠状态(S3 状态)。此选项在默认设置下 已禁用。 Intel Ready Mode 允许您启用 Intel Ready Mode Technology 的功能。此选项在默认设置下已禁 用。 表.
选项 说明 注: 如果未选中此选项,系统固件快擦写到以前版本会被阻止。 Data Wipe 允许您安全地擦除所有可用内部存储设备中的数据,如 HDD、SSD、mSATA 和 eMMC。此选项在默认设置下已禁用。 BIOS recovery 允许您从主硬盘驱动器或外部 USB 盘上的恢复文件恢复已损坏的 BIOS 条件。 表. 16: Cloud desktop(云桌面) 选项 Server Lookup Method 说明 允许您指定云桌面软件查询服务器地址的方法。 • • Static(静态) DNS(默认设置) Server Name 允许您指定服务器的名称 Server IP Address 指定云桌面服务器的主静态 IP 地址。默认 IP 地址为 255.255.255.
更新 BIOS 如果更新可用,建议在更换的系统板上更新 BIOS(系统设置程序)。对于笔记本电脑,确保计算机电池充满 电并已连接到电源插座。 1. 重新启动计算机。 2. 访问 Dell.com/support。 3. 输入服务标签或快速服务代码,然后单击 Submit(提交)。 注: 要找到服务标签,请单击 Where is my Service Tag?(我的服务标签在哪里?) 注: 如果您无法找到服务标签,请单击 Detect My Product(检测我的产品)。继续按照屏幕上的说 明进行操作。 4. 如果您无法找到或查找服务标签,请单击计算机的产品类别。 5. 从列表选择产品类型。 6. 选择您的计算机型号,您计算机的产品支持页面将会出现。 7. 单击 Get drivers(获得驱动程序),然后单击 View All Drivers(查看全部驱动程序)。 驱动程序和下载页面。 8. 在驱动程序和下载屏幕上,在 Operating System(操作系统)下拉列表中,选择 BIOS。 9.
分配系统密码和设置密码 仅当 Password Status(密码状态)为 Unlocked(已解锁)时,才可设定新的 System Password(系统密 码)和/或 Setup Password(设置密码)或者更改现有 System Password(系统密码)和/或 Setup Password(设置密码)。如果 Password Status(密码状态)为 Locked(锁定),则无法更改 System Password(系统密码)。 注: 如果密码跳线已禁用,将删除现有 System Password(系统密码)和 Setup Password(设置密 码),无需提供系统密码即可登录计算机。 要进入系统设置程序,开机或重新引导后立即按 F2。 1. 在 System BIOS (系统 BIOS)或 System Setup(系统设置程序)屏幕中,选择 System Security(系 统安全保护)并按 Enter。 会出现 System Security(系统安全保护)屏幕。 2.
注: 如果更改系统密码和/或设置密码,则需要在提示时重新输入新密码。如果删除系统密码和/或设 置密码,则需要在提示时确认删除。 5. 按 Esc 将出现一条消息提示您保存更改。 6.
5 规格 注: 所提供的配置在不同地区可能会有所差异。请按照下列方式获取计算机配置的详细信息: • Windows 10,单击或点按开始 • Windows 8.1 和 Windows 8,单击或点按开始 • Windows 7,单击开始 → 设置 → 系统 → 关于。 → PC 设置 → PC 和设备 → PC 信息。 ,右键单击 我的电脑,然后选择属性。 表. 19: 处理器 功能 规格 处理器类型 第 6 代 Intel Core i3/i5/i7 系列 总高速缓存 根据处理器类型的不同,高速缓存最大 8 MB 表. 20: 内存 功能 规格 类型 DDR4 速度 2133 MHz 连接器 四个 UDIMM 插槽 内存模块容量 4 GB 和 8 GB 最小内存 4 GB 注: 根据计算机上安装的操作系统,最小内存可能有所 不同。 最大内存 32 GB 注: 每个 UDIMM 插槽支持最小 4 GB 和最大 8 GB 的 内存。 表.
表. 22: 音频 功能 规格 集成 两个声道高保真音频 表. 23: 网络 功能 规格 集成 Intel I219LM 以太网,支持 10/100/1000 Mb/s 通信 表. 24: 系统信息 功能 规格 系统芯片组 Intel 100 系列、Q170 DMA 通道 两个 8237 DMA 控制器,带有七个独立可编程通道 中断级别 集成 I/O APIC 功能(24 个中断) BIOS 芯片 (NVRAM) 16 MB 表. 25: 扩展总线 功能 规格 总线类型 PCIe gen3 (x16)、USB 2.0 和 USB 3.0 总线速率 PCI Express: • • x4 插槽双向速率 – 最大 3.94 GB/s x16 插槽单向速率 – 16 GB/s SATA:1.5 Gbps、3.0 Gbps 和 6 Gbps 表. 26: 插卡 功能 规格 PCI express x4 半高插卡 PCI express x16 半高插卡 表. 27: 驱动器 功能 规格 外部可抽换(5.
功能 规格 背面板 输出连接器 网络适配器 RJ-45 连接器 串行 9 针连接器;16550 C 兼容 并行 25 针连接器(可选) USB 2.0 • • 前面板:两个 背面板:2 个 USB 3.0 • • 前面板:2 个 背面板:四个 视频 • • • 19 针 HDMI 连接器 两个 20 针 DisplayPort 连接器 15 针 VGA 连接器(可选) 注: 可用的视频连接器可能因所选图形卡的不同而有所 差异。 键盘和鼠标 背面板: • • PS2 键盘 6 针连接器 PS2 鼠标 6 针连接器 表. 29: 内部连接器 功能 规格 PCI Express x16(以 x4 接驳)数据宽度(最 大)— 四个 PCI Express 信道 164 针连接器 PCI Express x16 数据宽度(最大)— 16 个 PCI 164 针连接器 Express 信道 串行 ATA 三个 7 针连接器 内存 四个 288 针连接器 内置 USB 10 针连接器 系统风扇 4 针接口 SSD M.
功能 规格 内置扬声器 4 针接口 防盗开关连接器 3 针连接器 电源连接器 一个 8 针用于 PSU、一个 4 针用于 CPU、一个 6 针用于 SATA 电源 表.
功能 规格 厚度 312.00 毫米(8.38 英寸) 重量 6.00 千克(13.22 磅) 表. 33: 环境参数 功能 规格 温度范围 运行时 5°C 至 35°C(41°F 至 95°F) 存储时 –40°C 至 65°C(–40°F 至 149°F) 相对湿度(最大值) 运行时 20% 到 80%(非冷凝) 存储时 5% 到 95%(非冷凝) 最大振动 运行时 0.26 Grms 存储时 2.20 Grms 最大撞击 运行时 40 G 存储时 105 G 海拔高度 52 运行时 –15.2 米至 2000 米(–50 英尺至 6560 英尺) 存储时 –15.20 米至 10,668 米(–50 英尺至 35,000 英尺) 气载污染物级别 G1 或更低(根据 ANSI/ISA-S71.
联系 Dell 6 注: 如果没有活动的 Internet 连接,您可以在购货发票、装箱单、帐单或 Dell 产品目录上查找联系信 息。 Dell 提供了若干联机及电话支持和服务选项。服务会因所在国家和地区以及产品的不同而有所差异,您所在的 地区可能不提供某些服务。如要联系 Dell 解决有关销售、技术支持或客户服务问题: 1. 请转至 Dell.com/support。 2. 选择您的支持类别。 3. 在页面底部的选择国家/地区下拉列表中,确认您所在的国家或地区。 4.