Dell OptiPlex 7070 Ultra Setup and Specifications
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Views...........................................................................................................................................4 Exploded view........................................................................................................................................................................ 4 Top view...................................................................................................................................................................
1 Views Exploded view 1. Stand 2. OptiPlex 7070 Ultra 3.
Bottom view Table 1. Bottom view Callout Description USB 3.1 Gen 2 Type-C port with DisplayPort Alt Mode/Power Delivery Power-adapter port Network RJ-45 port USB 3.1 Gen 2 Type-A port with SmartPower USB 3.
Table 2. Left and right view Callout Description Service tag location Universal audio jack Hard-drive status LED USB 3.1 Gen 2 Type-C port with DisplayPort Alt Mode USB 3.
2 Set up your OptiPlex 7070 Ultra Installing the device on a fixed stand Steps 1. Align and insert the slots on the fixed stand into the tab on the stand base. 2. Lift and tilt the stand base. 3. Tighten the captive screw to secure the stand to the base. 4. Slide the release latch on the stand, until you hear a click, to release the stand cover. 5. Slide and lift the cover to release it from the stand.
6. Remove the screw that secures the stand mounting bracket to the stand. 7. Lift the mounting bracket to release the hooks on the bracket from the slots on the stand.
8. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 9. Align the screws on the mounting bracket with the screw holes on the monitor. 10. Tighten the four captive screws to secure the mounting bracket to the monitor.
11. Select the height at which you want to mount the monitor and align the hooks on the mounting bracket with the slots on the stand. 12. Replace the screw to secure the fixed stand to the monitor.
13. Align the vents on the device with the vents on the stand cover. 14. Lower the device in the stand until you hear a click. 15. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet. NOTE: To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image.
16. Slide the back cover, along with the device, into the stand until you hear a click. 17. Lock the device and the stand cover.
18. Press the power button to turn on the device.
Set up your OptiPlex 7070 Ultra
Monitor tilt angle Installing the device on a height-adjustable stand Steps 1. Align and insert the slots on the height-adjustable stand into the tab on the stand base. 2. Lift and tilt the stand base. 3. Tighten the captive screw to secure the stand to the base.
4. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 5. For installing the height-adjustable stand to the monitor: a) Align and insert the hooks on the mounting bracket on the stand into the slots on the monitor, until you hear a click.
6. For installing QR to VESA bracket for E-Series monitor: a) b) c) d) Align the screw holes on the QR to VESA bracket with the screw holes on the monitor. Install the four screw spacers and the screws to secure the QR to VESA bracket to the monitor. Align and insert the QR tabs on the stand into the slots on the QR to VESA bracket on the monitor. Tighten the thumb screw to secure the stand to the QR to VESA bracket.
7. To release the stand cover, slide the release latch until you hear a click. 8. Slide and lift the cover to release it from the stand. 9. Align the vents on the device with the vents on the stand cover. 10. Lower the device in the stand until you hear a click.
11. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet. NOTE: To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image. 12. Slide the back cover, along with the device, into the stand until you hear a click.
13. Lock the device and the stand cover. 14. Press the power button to turn on the device.
Set up your OptiPlex 7070 Ultra 21
Stand tilt, pivot, and swivel images Installing device on offset VESA mount Steps 1. Align the screw holes on the device with the screw holes on the offset VESA mount. 2. Install the four screws to secure the device to the offset VESA mount.
3. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 4. Align the screw holes on the offset VESA mount with the screw holes on the monitor. 5. Install the four screw spacers and the screws to secure the offset VESA mount to the monitor.
6. Insert the hooks on the mounting bracket of the monitor arm stand into the slots on the offset VESA mount on the monitor. 7. Lower the monitor on the monitor arm stand until you hear a click.
NOTE: To install the offset VESA mount on a Dell E-Series monitor, remove the VESA cover from the back of the monitor and secure the offset VESA mount along with the device to the monitor.
NOTE: While orienting the monitor horizontally, route the security lock cable to the right side of the device to avoid any impact to WLAN performance.
3 Powering the system OptiPlex 7070 Ultra can be powered using a AC adapter (4.5 mm input power source) or through the USB Type-C cable connected to your display. During normal operation, when the device is connected with a single power source (primary power source), connecting a second power source and disconnecting the primary power source will shut down the device. However, if the secondary power source is disconnected while the primary power source is connected, the system continues to operate normally.
4 Smart power enablement Deep sleep is enabled in the BIOS by default. If the system is connected to a USB keyboard and Deep sleep is enabled in the BIOS, the system will not power on or wake from hibernation when a key is pressed on the USB keyboard. Enable USB Wake support: 1. 2. 3. 4. 5. 6. 28 Press when the Dell logo appears to initiate a one-time boot menu. Go to BIOS Setup. Select Power Management.
5 Specifications of OptiPlex 7070 Ultra Processors Table 4. Processors Processors Wattage Core count Thread count Speed Cache Integrated graphics 8th Generation Intel Core i3-8145U 25 W 2 4 2.10 GHz to 3.90 GHz 4 MB Intel UHD Graphics 620 8th Generation Intel Core i5-8265U 25 W 4 8 1.60 GHz to 3.90 GHz 6 MB Intel UHD Graphics 620 8th Generation Intel Core i5-8365U 25 W 4 8 1.60 GHz to 4.10 GHz 6 MB Intel UHD Graphics 620 8th Generation Intel Core i7-8565U 25 W 4 8 1.
Description Values Speed 2400 MHz Maximum memory 64 GB Minimum memory 4 GB Memory size per slot 4 GB, 8 GB, 16 GB, 32 GB Configurations supported • • • • • 4 GB (1 x 4 GB) 8 GB (1 x 8 GB, 2 x 4 GB) 16 GB (1 x 16 GB, 2 x 8 GB) 32 GB (1 x 32 GB, 2 x 16 GB) 64 GB (2 x 32 GB) Storage Your computer supports the following configuration: • One 2.5 inch, 7 mm hard drive and One M.2 2230 solid-state drive Table 7. Storage specifications Storage type Interface type Capacity 2.
Table 9. Internal ports and connectors Description Values Internal: M.2 • • 1 M.2 slot for 2230 M.2 WiFi and Bluetooth card 1 M.2 slot for 2230 M.2 PCIe solid-state drive NOTE: To learn more about the features of different types of M.2 cards, see the knowledge base article SLN301626. SATA 1 SATA 3.0 FFC connector for hard drive Audio Table 10.
Wireless module Table 13. Wireless module specifications Description Values Model number Qualcomm QCA61x4A Intel Wi-Fi 6 AX200 Transfer rate Up to 867 Mbps Up to 2.4 Gbps Frequency bands supported 2.4 GHz, 5 GHz 2.4 GHz, 5 GHz Wireless standards • • • Wi-Fi 802.11 a/b/g Wi-Fi 4 (WiFi 802.11n) Wi-Fi 5 (WiFi 802.11ac) • • • • Wi-Fi 802.11 a/b/g Wi-Fi 4 (Wi-Fi 802.11n) Wi-Fi 5 (Wi-Fi 802.11ac) Wi-Fi 6 (Wi-Fi 802.
Description Values Width 96.10 mm (3.78 in.) Depth 256.20 mm (10.09 in.) Weight (maximum) maximum 0.65 kg (1.43 lb) NOTE: The weight of your computer depends on the configuration ordered and the manufacturing variability. Accessories Table 16. Accessories Accessories Stands and Mounts OptiPlex Ultra Fixed Stand OptiPlex Ultra Height Adjustable Stand OptiPlex Ultra Offset VESA Mount Cables OptiPlex Ultra USB C to USB C cable, 0.6 meter OptiPlex Ultra USB-A to USB-B 3.0 cable, 0.
Energy Star and Trusted Platform Module (TPM) Table 17. Energy star and TPM Features Specifications Energy Star Energy Star 7 compliant TPM • • Environmental, Ergonomic and Regulatory standards Environmental Standards (eco-labels): ENERGY STAR, EPEAT Registered, TCO Certified, CEL, WEEE, Japan Energy Law, South Korea E-standby, South Korea Eco-label, EU RoHS, China RoHS.
