OptiPlex 7090 Ultra Setup and specifications guide Regulatory Model: D13U Regulatory Type: D13U002 January 2021 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Set up your OptiPlex 7090 Ultra................................................................................... 5 Installing the device on a fixed stand............................................................................................................................. 5 Monitor tilt angle..........................................................................................................................................................
Chapter 5: Getting help...............................................................................................................90 Contacting Dell..................................................................................................................................................................
1 Set up your OptiPlex 7090 Ultra Topics: • • • • • Installing Installing Installing Installing Installing the device on a fixed stand the device on a Pro 1 height-adjustable stand device on offset VESA mount the device on a Pro 2 height-adjustable stand device on Wall Mount Installing the device on a fixed stand 1. Align and insert the slots on the fixed stand into the tab on the stand base. 2. Lift and tilt the stand base. 3. Tighten the captive screw to secure the stand to the base. 4.
. Remove the screw that secures the stand mounting bracket to the stand. 7. Lift the mounting bracket to release the hooks on the bracket from the slots on the stand.
8. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 9. Align the screws on the mounting bracket with the screw holes on the monitor. 10. Tighten the four captive screws to secure the mounting bracket to the monitor.
11. Select the height at which you want to mount the monitor and align the hooks on the mounting bracket with the slots on the stand. 12. Replace the screw to secure the fixed stand to the monitor.
13. Align the vents on the device with the vents on the stand cover. 14. Lower the device in the stand until you hear a click. 15. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet. NOTE: To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image.
NOTE: All the cables and ports are used depending on the peripherals chosen and the configuration of the computer. 16. Slide the back cover, along with the device, into the stand until you hear a click.
17. Lock the device and the stand cover.
18. Press the power button to turn on the device.
Set up your OptiPlex 7090 Ultra 13
Monitor tilt angle Installing the device on a Pro 1 height-adjustable stand 1. Align and insert the slots on the height-adjustable stand into the tab on the stand base. 2. Lift and tilt the stand base. 3. Tighten the captive screw to secure the stand to the base.
4. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 5. For installing the height-adjustable stand to the monitor: a. Align and insert the hooks on the mounting bracket on the stand into the slots on the monitor, until you hear a click.
6. For installing QR to VESA bracket for E-Series monitor: a. b. c. d. 16 Align the screw holes on the QR to VESA bracket with the screw holes on the monitor. Install the four screw spacers and the screws to secure the QR to VESA bracket to the monitor. Align and insert the QR tabs on the stand into the slots on the QR to VESA bracket on the monitor. Tighten the thumb screw to secure the stand to the QR to VESA bracket.
7. To release the stand cover, slide the release latch until you hear a click. 8. Slide and lift the cover to release it from the stand. 9. Align the vents on the device with the vents on the stand cover. 10. Lower the device in the stand until you hear a click.
11. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet. NOTE: To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image. NOTE: All the cables and ports are used depending on the peripherals chosen and the configuration of the computer.
12. Slide the back cover, along with the device, into the stand until you hear a click.
13. Lock the device and the stand cover.
14. Press the power button to turn on the device.
Set up your OptiPlex 7090 Ultra
Stand tilt, pivot, and swivel images Installing device on offset VESA mount 1. Align the screw holes on the device with the screw holes on the offset VESA mount. 2. Install the four screws to secure the device to the offset VESA mount.
3. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 4. Align the screw holes on the offset VESA mount with the screw holes on the monitor. 5. Install the four screw spacers and the screws to secure the offset VESA mount to the monitor.
6. Insert the hooks on the mounting bracket of the monitor arm stand into the slots on the offset VESA mount on the monitor. 7. Lower the monitor on the monitor arm stand until you hear a click.
8. To install the offset VESA mount on a Dell E-Series monitor: a. Align and install the four screws to secure the device to the offset VESA mount.
b. Remove the VESA cover from the back of the monitor and secure the offset VESA mount along with the device to the monitor.
Set up your OptiPlex 7090 Ultra
Set up your OptiPlex 7090 Ultra 29
NOTE: While orienting the monitor horizontally, route the security lock cable to the right side of the device to avoid any impact to WLAN performance. Installing the device on a Pro 2 height-adjustable stand 1. Align and insert the slots on the height-adjustable stand into the tab on the stand base. 2. Lift and tilt the stand base. 3. Tighten the captive screw to secure the stand to the base.
NOTE: For the large height adjustable stand, replacing the screw to the unlock icon screw hole in the stand base ensures the rotation of the 30-inch - 32-inch monitor.
4. To avoid any damage to the monitor, ensure that you place the monitor on a protective sheet. 5. For installing the height-adjustable stand to the monitor: a. Align and insert the hooks on the mounting bracket on the stand into the slots on the monitor, until you hear a click.
Set up your OptiPlex 7090 Ultra 33
6. For installing QR to VESA bracket for E-Series monitor: a. b. c. d. 34 Align the screw holes on the QR to VESA bracket with the screw holes on the monitor. Install the four screw spacers and the screws to secure the QR to VESA bracket to the monitor. Align and insert the QR tabs on the stand into the slots on the QR to VESA bracket on the monitor. Tighten the thumb screw to secure the stand to the QR to VESA bracket.
Set up your OptiPlex 7090 Ultra 35
7. To release the stand cover, press the button on the side of the stand chassis. 8. Slide and lift the cover to release it from the stand.
9. Slide and release the inner bar on the lower edge of the stand cover.
10. Align the vents on the device with the vents on the stand cover and slide the device in the cover.
11. Slide the inner bar back to the lower edge of the stand cover to lock the device to the cover.
12. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet.
13. To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image. NOTE: All the cables and ports are used depending on the peripherals chosen and the configuration of the computer.
Large Height Adjustable Stand 42 Set up your OptiPlex 7090 Ultra
14. Slide the stand cover, along with the device, into the stand until you hear a click.
15. Lock the device and the stand cover.
16. Press the power button to turn on the device.
Stand tilt, pivot, and swivel images For 19-inch to 27-inch monitor (Standard height adjustable stand): 46 Set up your OptiPlex 7090 Ultra
For 30-inch to 32-inch monitor (Large height adjustable stand): Set up your OptiPlex 7090 Ultra 47
For monitors > 32-inch (Large height adjustable stand): 48 Set up your OptiPlex 7090 Ultra
Installing device on Wall Mount 1. Full Function a. Press the release button to open the cable cover. b. Align the screw holes on the wall mount in the wall and mark them against the wall using a pencil.
c. Drill the screw marks on the wall and insert the three screw anchors into the screw holes in the wall.
d. Align the screw holes on the wall mount with the screw holes on the wall and install the three screws to secure the wall mount in the wall.
e. Align the screw holes on the device with the screw holes on the wall mount bracket. f. Install the four screws to secure the device to the wall mount bracket.
g. Insert the hooks on the mounting bracket of the wall mount into the slots on the wall mount bracket module. h.
i. 54 Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet.
j. To avoid any pinching or crimping of the cables while closing the stand cover, it is recommended that you route the cables as indicated in the image. NOTE: All the cables and ports are used depending on the peripherals chosen and the configuration of the computer.
k. Close the stand cover.
l. Lock the device and the stand cover.
2. Simple Function a. Align the screw holes on the wall mount in the wall and mark them using a pencil.
b. Drill the screw marks on the wall and insert the two screws into the screw holes in the wall.
c. Align the screw holes on the device with the screw holes on the wall mount bracket. d. Install the four screws to secure the device to the wall mount bracket.
e. Connect the power, network, keyboard, mouse, and display cables to the device and to the power outlet.
f. Align the screws on the wall with the retention clips on the wall mount bracket module. g. Mount the wall mount bracket module in the screws on the wall.
h. Press the power button to turn on the device.
Set up your OptiPlex 7090 Ultra
2 Create a USB recovery drive for Windows Create a recovery drive to troubleshoot and fix problems that may occur with Windows. An empty USB flash drive with a minimum capacity of 16 GB is required to create the recovery drive. NOTE: This process may take up to an hour to complete. NOTE: The following steps may vary depending on the version of Windows installed. Refer to the Microsoft support site for latest instructions. 1. Connect the USB flash drive to your computer. 2. In Windows search, type Recovery.
3 View of OptiPlex 7090 Ultra Topics: • • • • • • • Top Bottom Left Right Front and back Stands view System board layout Top 1. Fan vent 2.
Bottom 1. 2. 3. 4. 5. 6. DisplayPort 1.4 + + HBR2 1 USB 3.2 Gen 2 Type-A ports with SmartPower On 1 USB 3.2 Gen 2 Type-A ports with SmartPower On RJ45 Ethernet port DC-in port 1 USB 3.
Left 1. 2. 3. 4. 5. 68 Headset/Universal Audio Jack Fan vent Hard-drive status LED 1 Thunderbolt 4 port with DisplayPort Alt Mode/USB4 1 USB 3.
Right 1. Kensington lock slot 2. Security screw lock slot 3.
Back 70 View of OptiPlex 7090 Ultra
1. Hard drive cover/ M.
Pro 1.0 Height-adjustable stand: Pro 2.
Pro 2.
Offset VESA Mount: 74 View of OptiPlex 7090 Ultra
VESA Adapter for Pro2.
VESA Adapter for Pro1.
Wall Mount: View of OptiPlex 7090 Ultra 77
View of OptiPlex 7090 Ultra
System board layout 1. 2. 3. 4. 5. 6. 7. 8. 9. System fan connector Power button connector Coin-cell battery connector Hard-drive connector Daughter board connector CPU M.2 SSD PCIe Gen4 connector M.
4 Specifications of OptiPlex 7090 Ultra Topics: • • • • • • • • • • • • • • • • • • • • • • Dimensions and weight Processor Chipset Operating system Commercial platform Windows 10 N-2 and 5yrs OS supportability Memory Intel Optane Memory H10 with Solid State Storage External ports Internal slots Ethernet Wireless module Audio Storage Power adapter GPU—Integrated Powering the system Type-C display settings Dell power button sync Data security Computer environment Energy Star and Trusted Platform Module (TPM
Processor The following table lists the details of the processors supported by your OptiPlex 7090 Ultra. Table 2. Processor Description Option one Option two Option three Processor type 11 th Generation Intel Core i3-1115G4 11 th Generation Intel Core i5-1145G7 vPRO 11 th Generation Intel Core i7-1185G7 vPRO Processor wattage 28 W 28 W 28 W Processor core count 2 4 4 Processor thread count 4 8 8 Processor speed 3.0 GHz to 4.1 GHz 2.6 GHz to 4.4 GHz 3.0 GHz to 4.
For future versions of Windows 10, Dell will continue to test the commercial platform with coming Windows 10 releases during device production and for five years post-production, including both fall and spring releases from Microsoft. Please reference the Dell Windows as a Service (WaaS) website for additional information on N-2 and 5 year Windows OS supportability. Website can be found at this link: https://www.dell.
NOTE: Intel Optane Memory H10 with Solid State Storage is supported on computers that meet the following requirements: ● 9 th Generation or higher Intel Core i3/i5/i7 processors ● Windows 10 64-bit version or higher (Anniversary Update) ● Intel Rapid Storage Technology driver version 15.9.1.1018 or higher External ports The following table lists the external ports of your OptiPlex 7090 Ultra. Table 6. External ports Description Values Network port 1 RJ-45 Ethernet port USB ports ● 1 USB 3.
Ethernet Table 8. Ethernet specifications Description Values Model number Intel i219LM Transfer rate 10/100/1000 Mbps Wireless module The following table lists the Wireless Local Area Network (WLAN) modules supported on your OptiPlex 7090 Ultra. Table 9. Wireless module specifications Description Option one Option two Model number Qualcomm QCA61x4A Intel Wi-Fi 6 AX201 Transfer rate Up to 867 Mbps Up to 2.4 Gbps Frequency bands supported 2.4 GHz, 5 GHz 2.
● ● ● ● ● ● ● One M.2 2230 solid-state drive One M.2 2230 solid-state drive and One M.2 2230 solid-state drive One M.2 2230 solid-state drive and One M.2 2280 solid-state drive One M.2 2230 solid-state drive and One 2.5-inch, 7 mm hard drive One M.2 2280 solid-state drive One 2.5-inch, 7 mm hard drive One M.2 2230 solid-state drive and One Intel Optane Memory H20 with Solid State Storage, 512 GB, M.2 2280, PCIe NVMe Gen3 x4 ● One Intel Optane Memory H20 with Solid State Storage, 512 GB, M.
Table 12. Power adapter specifications (continued) Description Values Temperature range: Operating 0°C to 40°C (32°F to 104°F) Storage -40°C to 70°C (-40°F to 158°F) GPU—Integrated The following table lists the specifications of the integrated Graphics Processing Unit (GPU) supported by your OptiPlex 7090 Ultra. Table 13.
When the device is powered with both the power sources—AC adapter and USB Type-C cable, the AC adapter is the primary power source and USB Type-C is the secondary power source. Disconnecting the AC adapter will shut down the system. If the secondary power source is disconnected, the system continues to operate normally. NOTE: Hotswap between the AC adapter and USB Type-C power source is not supported. Table 14.
Data security Table 15.
Energy Star and Trusted Platform Module (TPM) Table 17. Energy star and TPM Features Specifications Energy Star ENERGY STAR 8.0 qualified Compliant TPM ● Hardware trusted Platform Module (Discrete TPM Enabled) ● Firmware Trusted Platform Module only (Discrete TPM Disabled) Environmental, Ergonomic and Regulatory standards Environmental Standards (eco-labels): ENERGY STAR, EPEAT Registered, TCO Certified, CEL, WEEE, Japan Energy Law, South Korea E-standby, South Korea Eco-label, EU RoHS, China RoHS.
5 Getting help Topics: • Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Go to Dell.com/support. 2.
