Dell OptiPlex 7450 All-In-One Owner's Manual Regulatory Model: W11C Regulatory Type: W11C002
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2017 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Working on your computer............................................................................................................................. 7 Before working inside your computer.............................................................................................................................. 7 Safety instructions.............................................................................................................................................................
Installing the coin cell battery................................................................................................................................... 23 WLAN card....................................................................................................................................................................... 24 Removing the WLAN card........................................................................................................................................
4 Technology and components........................................................................................................................49 Chipsets............................................................................................................................................................................ 49 Identifying the chipset in Device Manager on Windows 10.................................................................................. 49 Storage options......................
Kaby Lake — 7th Generation Intel Core processors.............................................................................................. 71 Identifying processors in Windows 10......................................................................................................................72 Identifying processors in Windows 7....................................................................................................................... 72 Memory specifications..............................
1 Working on your computer Before working inside your computer To avoid damaging your computer, perform the following steps before you begin working inside the computer. 1 Ensure that you follow the Safety Instruction. 2 Ensure that your work surface is flat and clean to prevent the computer cover from being scratched. 3 Ensure you follow the Turning off your computer . 4 Disconnect all network cables from the computer.
• Small flat blade screwdriver • Phillips # 1 screwdriver • Small plastic scribe Turning off your computer Turning off your computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1 Turning off your computer (Windows 8.1): • Using a touch enabled device: a b Swipe in from the right edge of the screen, opening the Charms menu and select Settings. Select and then select Shut down.
After working inside your computer After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your computer. 1 Connect any telephone or network cables to your computer. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 2 Connect your computer and all attached devices to their electrical outlets. 3 Turn on your computer.
2 Removing and installing components This section provides detailed information on how to remove or install the components from your computer. Stand Removing the stand NOTE: The system is shipped with three different type of stands: • Height Adjustable Stand • Basic Stand • Articulating Stand The removal procedure is the same for all the three stands. 1 Follow the procedure in Before working inside your computer. 2 Place the computer on clean, flat surface with the display facing downward.
Figure 1. Height Adjustable Stand Figure 2.
Figure 3. Articulate stand Installing the stand 1 Place the computer on a clean, flat surface and align the stand, and then slide it on the back of the computer. 2 Press the stand down till it snaps in. 3 Follow the procedure in After working inside your computer. Cable cover Removing the cable cover 1 Follow the procedure in Before working inside your computer. 2 Remove the stand. 3 To remove the cable cover: a b c 12 Remove the screw that secures the cable cover to the computer [1].
Installing the cable cover 1 Align the notches on the cable cover to the holes on the computer and press the cable cover until it snaps in. 2 Tighten the screw to secure the cable cover to the computer. 3 Install the stand. 4 Follow the procedure in After working inside your computer. Back cover Removing the back cover 1 Follow the procedure in Before working inside your computer.
4 Lift the back cover from the computer. Installing the back cover 1 Align the notches on the back cover to the holes on the computer, and press the back cover until it snaps in.
a b 3 cable cover stand Follow the procedure in After working inside your computer. Optical drive Removing the optical drive assembly 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b 3 To remove the optical drive assembly: a b 4 stand back cover Press the securing tab at the base of the drive to release the optical drive assembly [1]. Slide the optical drive assembly to remove it away from the computer [3][2].
Installing the optical drive assembly 1 Place the bracket to align the screw holders on the optical drive. 2 Tighten the screws to secure the bracket to the optical drive. 3 Insert the optical drive assembly into the drive slot, until it snaps in. 4 Install the: a b 5 back cover stand Follow the procedure in After working inside your computer.
Installing the power and OSD buttons board 1 Connect the cable to the power and OSD buttons board. 2 Affix the tape on the OSD buttons board. 3 Insert the power and OSD buttons board into the slot. 4 Align the metal plate on the power and OSD buttons board. 5 Tighten the screw to secure the power and OSD buttons board. 6 Install the: a b c 7 optical drive back cover stand Follow the procedure in After working inside your computer.
4 Pull and remove the speaker cover from the computer. NOTE: To avoid damage to the back cover, release it from the pull tabs. Installing the speaker cover 1 Align and push the speaker cover to pop tabs into its position on the back of the computer. 2 Tighten the screws to secure the speaker cover to the computer. 3 Install the: a b c 4 back cover cable cover stand Follow the procedure in After Working Inside Your Computer.
Hard drive Removing the hard drive assembly 1 Follow the procedure in Before working inside your computer. 2 Remove the: a stand b back cover 3 To remove the hard drive assembly: a Press the tab on the bracket, and slide the hard-drive assembly until the tabs are released from either side of the assembly [1]. b Slide the hard-drive assembly upwards to remove it from the computer [2]. 4 To remove the hard drive bracket: a Pry the edges of the bracket to release the hard drive [1].
Installing the hard drive assembly 1 Align the hard drive until the notches are aligned and the hard drive is secured in the bracket. 2 Place the hard drive onto the hard drive cage until the notches are aligned, then slide the Hard Drive assembly until the tab locks into the cage. 3 Install the: a b 4 back cover stand Follow the procedure in After working inside your computer. System board shield Removing the system board shield 1 Follow the procedure in Before working inside your computer.
Installing the system board shield 1 Align and slide the system board shield until it snaps in. 2 Install the: a b 3 back cover stand Follow the procedure in After working inside your computer. Memory modules Removing the memory module 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c 3 stand back cover system board shield To remove the memory module: a b Pry the retention clips away from the memory module until it pops up [1].
a b c 3 system board shield back cover stand Follow the procedure in After working inside your computer. Solid State Drive — optional Removing the SSD card 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c 3 stand back cover system board shield To remove the SSD card: a b Remove the screw that secures the SSD card to the computer [1]. Lift the SSD card away from the connector [2]. Installing the SSD card 1 Insert the SSD card into the connector.
b c 4 back cover stand Follow the procedure in After working inside your computer. Coin cell battery Removing the coin cell battery 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c 3 stand back cover system board shield Press the latch to release the coin cell battery and remove it from the computer. Installing the coin cell battery 1 Insert the coin cell battery into the slot on the system board until it fits securely.
WLAN card Removing the WLAN card 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c 3 stand back cover system board shield To remove the WLAN card: a b c Disconnect the antenna cables from the connectors on the WLAN card [1]. Remove the screw that secures the WLAN card to the system board [2]. Hold the WLAN card and pull it from the connector on the system board [3]. Installing the WLAN card 1 Align the WLAN card to the connector on the system board.
Heat sink Removing the heat sink 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c 3 stand back cover system board shield To remove the heat sink: a b Remove the screws that secure the heat sink to the chassis [1, 2]. Lift the heat sink away from the computer [3]. Installing the heat sink 1 Align and place the heat sink in the slot. 2 Tighten the screws to secure the heat sink to the computer.
Speaker Removing the speaker module 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c d e 3 To release the speaker module: a b 4 stand back cover cable cover speaker cover system board shield Disconnect the speaker cable from the connector on the system board [1]. Unthread the speaker cables from the retention clips [2]. To remove the speaker module: a b 26 Remove the screws that secure the speaker module to the chassis [1].
Installing the speaker module 1 Insert the speaker module into the slot on the chassis. 2 Tighten the screws to secure the speaker to the chassis. 3 Secure the speaker cables through the retention clips. 4 Connect the speaker cable to the connector on the system board. 5 Install the: a b c d e 6 system board shield speaker cover back cover cable cover stand Follow the procedure in After working inside your computer.
a b Unthread the power supply cables from the retention clips in the chassis [1]. Disconnect the power supply cable from the connector on the system board [2]. NOTE: Press lock clip to release the power supply cable from the system board. 4 To release the PSU: • NOTE: There is an additional cable retention clip on the side of the VESA mount bracket. The PSU near that is not visible in the removing cables from retention clips image.
5 To remove the PSU: a b Remove the screw that secure the PSU to the chassis [1]. Slide the PSU and lift it away from the chassis [2].
Installing the Power Supply Unit - PSU 1 Place the PSU on the chassis. 2 Tighten the screw to secure the PSU to the chassis. 3 Place the power supply socket in the slot on the chassis. 4 Tighten the screw to secure the power supply socket to the chassis. 5 Secure the power supply cable on the retention clips in the chassis. 6 Connect the power supply cables to the connectors on the system board.
Installing the VESA mount bracket 1 Align and place the bracket in the slot on the computer. 2 Tighten the screws that secure the VESA mount bracket to the computer. 3 Install the: a b c d e f 4 power supply unit system board shield speaker cover cable cover back cover stand Follow the procedure in After working inside your computer. Converter board Removing the converter board 1 Follow the procedure in Before working inside your computer.
g 3 VESA mount bracket To remove the converter board: a b c d Disconnect the convertor board cable from the converter board [1]. Disconnect the display backlight cable from the converter board [2]. Remove the screws that secure the converter board to the computer [3]. Lift the converter board away from the computer [4]. Installing the converter board 1 Place the convertor board in the slot. 2 Tighten the screws to secure the converter board to the chassis.
System fan Removing the system fan 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c d e f g 3 stand back cover cable cover speaker cover system board shield power supply unit VESA mount bracket To remove the system fan: a b c Disconnect the system fan cable from the connector on the system board [1]. Remove the screws that secure the system fan to the computer [2]. Lift the system fan away from the computer [3].
c d e f g 5 system board shield speaker cover cable cover back cover stand Follow the procedure in After working inside your computer. Intrusion switch Removing the intrusion switch 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c d e f g 3 To remove the intrusion switch: a b c d 4 stand back cover cable cover speaker cover system board shield power supply unit VESA mount bracket Disconnect the intrusion switch cable from the connector on the system board [1].
Installing the intrusion switch 1 Place the intrusion switch in the slot on the computer. 2 Tighten the screw to secure the intrusion switch to the chassis. 3 Route intrusion switch cable along the retention clips on the chassis. 4 Connect the intrusion switch cable to the connector on the system board. 5 Install: a b c d e f g 6 VESA mount bracket power supply unit system board shield speaker cover cable cover back cover stand Follow the procedures in After working inside your computer.
a b Release the socket lever by pushing the lever down and out from under the tab on the processor shield [1]. Lift the lever upward and lift the processor shield [2]. c CAUTION: The processor socket pins are fragile and can be permanently damaged. Be careful not to bend the pins in the processor socket when removing the processor out of the socket. Lift the processor out of the socket [3]. NOTE: After removing the processor, place it in an antistatic container for reuse, return, or temporary storage.
a b c d e f g h i j k l m n o p q 3 Disconnect the following cables from the system board: a b c d e f g 4 stand back cover cable cover speaker cover speaker hard drive optical drive VESA mount bracket system board shield SSD card WLAN card memory heat sink system fan processor coin cell battery power supply unit intrusion switch [1] hard drive and optical drive [2] SATA [3] speaker [4] camera and microphone [5] display [6] system fan [7] To remove the system board: a b Remove the screws that secure th
Installing the system board 1 Place the system board on the computer. 2 Connect all the cables to the system board. 3 Tighten the screws to secure the system board to the base panel. 4 Install the: a b c d e f g h i j k l m n o p q 5 power supply unit coin cell battery system fan processor heat sink memory WLAN card SSD card system board shield VESA mount bracket optical drive hard drive cable cover speaker speaker cover back cover stand Follow the procedure in After working inside your computer.
System board layout 1 LVDS connector 2 Camera connector 3 Antenna wire clip 4 WLAN connector 5 Jumper connector 6 Coin cell battery 7 Speaker connector 8 Memory module connector 9 Jumper connector 10 M.
Removing the chassis frame NOTE: These instructions are applicable only for systems with a non-touch screen display. 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c d e f g h i j k l m n o p q r stand back cover cable cover speaker cover speaker hard drive optical drive VESA mount bracket system board shield SSD card WLAN card memory heat sink system fan processor coin cell battery power supply unit system board 3 Unroute the cables though the retention clips.
• NOTE: There is a cable that is taped/glued down to the chassis frame. That cable runs down from the On-Screen Display (OSD) and into a connector on the Display Bezel for the Power Button board below the OSD Button board. Trying to lift the chassis frame without disconnecting this cable first could damage the connector. a b Peel the adhesive tapes that secure the chassis frame [1]. Remove the screws that secure the chassis frame to the computer. [2].
Display panel Removing the display panel 1 Follow the procedure in Before working inside your computer. 2 Remove the: a b c d e f g h i j k l m n o p q r s 3 stand back cover cable cover speaker cover speaker hard drive optical drive VESA mount bracket system board shield SSD card WLAN card memory heat sink system fan processor coin cell battery power supply unit system board chassis frame To remove the display panel: a b c Disconnect the cables from the connectors [1].
4 Install the: a b c d e f g h i j k l m n o p q r s 5 chassis frame system board power supply unit coin cell battery system fan processor heat sink memory WLAN card system board shield SSD card VESA mount bracket optical drive hard drive cable cover speaker speaker cover back cover stand Follow the procedure in After working inside your computer.
3 M.2 Intel Optane Memory Module 16 GB Overview This document describes the specifications and capabilities of the Intel® OptaneTM memory module. The Intel® OptaneTM memory is a system acceleration solution developed for 7th Generation Intel® CoreTM processor-based platforms. The Intel® OptaneTM memory module is architected with the high performance controller interface Non-Volatile Memory Express (NVMe*)- delivering outstanding performance, low latency and quality of service.
b Place the M.2 Intel optane memory module into the slot on the computer. c Tighten the screw that secures the M.2 Intel optane memory module on the computer. Product specifications Table 2. Product specifications Features Specification Capacities 16 GB, 32 GB Expansion cards PCIe 3.0 x 2 M.
M.2 form factors (all densities) 2280–S3–B-M Performace • • • Seq R/W: Up to 1350/290 MS/s QD4 4HB Random Read: 240K + IOPs QD4 4HB Random Write: 240K + IOPs Latency (average sequential) • • Read 8.25 µ Write: 30 µ Components • • • • Intel 3D XPoint Memory Media Intel Controller and Firmware PCIe 3.0x2 with NVMe Interface Intel Rapid Storage Technology 15.
Environmental Conditions Table 3. Temperature, Shock, Vibration Temperature M.2 2280 form factor Operating1 0–70º C Non-operating 2 -10–85º C Temperature Gradient3 Operating 30º C/hr (Typical) Non-operating 30º C/hr (Typical) Humidity Operating 5–95% Non-operating 5–95% Shock and Vibration Range Shock 4 Operating 1500 G / 0.5 ms Non-operating 230 G / 3 msec Vibration5 Operating 2.17 GRMS (5–800Hz) Max Non-operating 3.
2 During the first-time boot up, the system will scan the pairing status as below screen shot after shutdown. It’s working as designed and the message will not appear again in following boot ups. 48 M.
4 Technology and components This chapter details the technology and components available in the system. Topics: • Chipsets • Storage options • Memory configurations • DDR4 Chipsets All laptops or notebook communicate with the CPU through the chipset. This laptop is shipped with the Intel Mobile CM238 .
Solid State Drives (SSD) Table 5. SSD • • • • • • • 2.5" 256 GB SATA Solid State Drive Class 20 2.5" 512 GB SATA Solid State Drive Class 20 M.2 128 GB SATA Solid State Drive Class 20 M.2 256 GB PCIe NVMe Solid State Drive Class 40 M.2 256 GB PCIe NVMe Self Encrypting Solid State Drive Class 40 M.2 512 GB PCIe NVMe Solid State DriveClass 40 M.
Verifying system memory in Windows 10 and Windows 7 Windows 10 1 Click the Windows button and select All Settings 2 Under System, click About. > System. Windows 7 1 Click Start → Control Panel → System DDR4 DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512 GB in capacity, compared to the DDR3's maximum capacity of 128 GB per DIMM.
Feature/Option DDR3 DDR4 DDR 4 Advantages DQ Bus SSTL15 POD12 Less I/O Noise and Power RTT Values (in &Omega) 120,60,40,30,20 240,120,80,60,48,40,34 Support for higher data rates RTT not allowed READ Bursts Disables during READ Bursts Ease of use ODT Modes Nominal, Dynamic Nominal, Dynamic,Park Add’l Control Mode; OTF Value Change ODT Control ODT Signaling Required ODT Signaling Not Required Ease of ODT Control; Allows Non-ODT Routing, PtP Apps Multi-Purpose Register Four Registers
DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation. Figure 6.
5 System setup System setup enables you to manage your hardware and specify BIOS level options.
Keys Navigation Down arrow Moves to the next field. Enter Selects a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop‐down list, if applicable. Tab Moves to the next focus area. NOTE: For the standard graphics browser only. Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message that prompts you to save any unsaved changes and restarts the system.
Option Description UEFI Booth Path Security This options controls whether or not the system will prompt the user to enter the Admin password when booting a UEFI boot path from the F12 Boot Menu. Date/Time • Always, Except Internal HDD • Always • Never: This option is enabled by default. Allows you to change the date and time. System configuration screen options Option Description Integrated NIC If you enable UEFI network stack, UEFI network protocols will be available.
Option Description If USB port is disabled, the OS cannot see any device attached to this port. The options are: • Enable Boot Support • Enable Rear USB Ports: Include options for 6 ports • Enable Front USB Ports: Include options for 2 ports All the options are enabled by default. NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these settings.
Option Description Default setting: Not set System Password Allows you to set, change or delete the system password. NOTE: Successful password changes take effect immediately. Default setting: Not set Strong Password Allows you to enforce the option to always set strong passwords. Default Setting: Enable Strong Password is not selected.
Option Description Default setting: Deactivate Chassis Intrusion This field controls the chassis intrusion feature. The options are: • Enabled • Disabled • On-slient Default Setting: Disabled OROM Keyboard Access Allows you to set an option to enter the Option ROM Configuration screens using hotkeys during boot.
Option Description NOTE: If you disable the Custom Mode, all the changes made will be erased and the keys will restore to default settings. Intel Software Guard Extensions options Option Description Intel SGX Enable Allows you to enable or disable the Intel Software Guard Extensions to provide a secured environment for running code/storing sensitive information in the context of the main operating system.
Option Description Default setting: The option is enabled. Power management screen options Option Description AC Recovery Specifies how the computer will respond when AC power is applied after an AC power loss. You can set the AC Recovery to: Auto On Time • Power Off (default) • Power On • Last Power State Allows you to set the time at which the computer must turn on automatically.
Option Description Block Sleep (S3 state) Default setting: This option is disabled Intel Ready Mode This option enables the capability of Intel Ready Mode technology. POST behavior screen options Option Description Numlock LED Specifies if the NumLock function can be enabled when the system boots. This option is enabled by default. Keyboard Errors Specifies whether keyboard related errors are reported when it boots. This option is enabled by default.
Maintenance screen options Option Description Service Tag Displays the Service Tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. SERR Messages Controls the SERR message mechanism. This option is enabled by default. Some graphics cards require that the SERR message mechanism be disabled. BIOS Downgrade This controls flashing of the system firmware to previous revisions.
3 Enter the Service Tag or Express Service Code and click Submit. a b To locate the Service Tag, click Where is my Service Tag? If you cannot find your Service Tag, click Detect My Product. Proceed with the instructions on screen. 4 If you are unable to locate or find the Service Tag, click the Choose from all products. 5 Choose the Products from the list. NOTE: Choose the appropriate category to reach the product page.
5 Press Y to save the changes. The computer reboots. Deleting or changing an existing system and or setup password Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked. To enter the System Setup, press F2 immediately after a power-on or reboot.
6 Troubleshooting your computer You can troubleshoot your computer using indicators like diagnostic lights, beep codes, and error messages during the operation of the computer. Enhanced Pre-Boot System Assessment — ePSA diagnostics The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the BIOS and is launched by the BIOS internally.
Troubleshooting your computer 67
Invoking BIST with user modes There are two methods to invoke the LCD BIST . • OSD Toggle • ePSA OSD toggle The first method of user initiation is via OSD toggle button. The user should press the OSD toggle button and hold it in while the power button is applied to turn the AIO on. This is the hardware-initiated method that does not require the CPU and BIOS to be functional. The panel will stay in BIST mode until the BIOS reboots the system.
approximately 20 seconds giving 2 cycles of color bar patterns that the user can observe. The time period is controlled by BIOS. After the time period, the BIOS will return the system to the ePSA menu.
7 Technical specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer in: • Windows 10, click or tap Start • Windows 8.1 and Windows 8, from the charms sidebar, click or tap Settings > Change PC settings. In the PC Settings window, select PC and devices > PC Info. > Settings > System > About. • Windows 7, click Start , right-click My Computer, and then select Properties.
Feature Specification • Intel Core i5-7500 Processor (Quad Core/ 6MB/ 4T/ 3.4GHz/ 65W) • Intel Core i5-7600 Processor (Quad Core/ 6MB/ 4T/ 3.5GHz/ 65W) • Intel Core i7-7700 Processor (Quad Core/ 8MB/ 8T/ 3.6GHz/ 65W) • Intel Pentium G4560 Processor (Dual Core/ 3MB/ 2T/ 3.5GHz/ 54W) Total cache Up to 8 MB cache depending on processor type Chipset Intel Q270 chipset Skylake — 6th Generation Intel Core processors Intel Skylake is the successor to the Intel Broadwell processor.
Kaby Lake specifications Table 8. Kaby Lake specifications Processor number Clock Speed Cache No. of cores/No. of threads Power Intel Pentium G4560 3,5 GHz 3 MB 2/2 54 W Intel Core i3-7100 3.9 GHz 3 MB 2/2 51 W Intel Core i5-7500 3.4 GHz 6 MB 4/4 65 W Intel Core i5-7600 3.5 GHz 6 MB 4/4 65 W Intel Core i7-7700 3.6 GHz 8 MB 8 65 W Identifying processors in Windows 10 1 Tap Search the Web and Windows. 2 Type Device Manager. The Device Manager window is displayed.
Feature Specification External display support DisplayPort, HDMI in and HDMI out (Optional only on FHD model configuration 7450 AIO) Audio specifications Feature Specification Controller Intel High Definition Audio with Waves MaxxVoice Pro Speaker single 4-ohms speakers in both the left and right speaker assembly (4 W average per channel) Internal speaker amplifier up to 7.
Port and connector specifications Feature Audio Specification • one line-out connector at rear • one global headset port at side Network adapter One RJ-45 connector USB 2.0 (Rear) 0(side)/2 USB 3.0 (Rear) 2(side)/4 USB port with 1(side) USB 3.
VESA wall mount Table 9. VESA stand specifications Type FDMI MIS-D, 100, C Hole mount pattern 100 x 100 mm Screw type M4 Minimum clearance from wall 20 mm (0.79 in) NOTE: Exercise caution not to block the rear venting holes while maintaining clearance from wall. Tilt -5 degrees to 30 degrees Physical specifications Feature Specification Width 575.24 mm (22.65 inches) Height 392.90 mm (15.47 inches) Depth: Non-touch 63.5 mm (2.5 inches) Touch 62.79 mm (2.47 inches) Weight: Non-touch 9.
Maximum shock Specifications Operating 40 G Storage 105 G Altitude (maximum) Specifications Operating 0 m to 5000 m (0 ft to 16,404 ft) Non-operating 0 m to 5000 m (0 ft to 16,404 ft) Airborne contaminant level G2 or lower as defined by ANSI/ISA-S71.
8 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Go to Dell.com/support. 2 Select your support category.
