Dell OptiPlex 7760 All-in-One Installationshandbuch für Intel Optane-Karte
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis 1 Bevor Sie beginnen.........................................................................................................................................4 Sicherheitshinweise............................................................................................................................................................4 Vor der Arbeit an Komponenten im Innern des Computers....................................................................................
1 Bevor Sie beginnen Sicherheitshinweise Beachten Sie folgende Sicherheitsrichtlinien, damit Ihr Computer vor möglichen Schäden geschützt und Ihre eigene Sicherheit sichergestellt ist. Wenn nicht anders angegeben, wird bei jedem in diesem Dokument vorgestellten Verfahren vorausgesetzt, dass folgende Bedingungen zutreffen: • Sie haben die im Lieferumfang des Computers enthaltenen Sicherheitshinweise gelesen.
6 Halten Sie den Betriebsschalter gedrückt, während Sie den Computer vom Netz trennen, um die Systemplatine zu erden. ANMERKUNG: Um elektrostatische Entladungen zu vermeiden, erden Sie sich mittels eines Erdungsarmbandes oder durch regelmäßiges Berühren einer nicht lackierten metallenen Oberfläche (beispielsweise eines Anschlusses auf der Rückseite des Computers).
elektrostatischen Schock erhalten hat und sofort das Symptom „No POST/No Video“ (Kein POST/Kein Video) mit einem Signaltoncode erzeugt, der im Falle von fehlendem oder nicht funktionsfähigem Speicher ertönt. • Gelegentlich: Gelegentliche Ausfälle machen etwa 80 Prozent der ESD-bezogenen Ausfälle aus. Die hohe Rate gelegentlicher Ausfälle bedeutet, dass auftretende Schäden in den meisten Fällen nicht sofort zu erkennen sind.
• ESD-Verpackung: Alle ESD-empfindlichen Geräte müssen in einer Schutzverpackung zur Vermeidung von elektrostatischer Aufladung geliefert und empfangen werden. Antistatische Beutel aus Metall werden bevorzugt. Beschädigte Teile sollten Sie immer unter Verwendung des gleichen ESD-Beutels und der gleichen ESD-Verpackung zurückschicken, die auch für den Versand des Teils verwendet wurde.
2 Intel Optane Einbauen der Intel Optane-Karte 1 Folgen Sie den Anweisungen unter Vor der Arbeit an Komponenten im Inneren des Computers. 2 Um eine Beschädigung des Bildschirms zu vermeiden, platzieren Sie das System auf einer ebenen, weichen und sauberen Oberfläche. 3 Entfernen Sie den Standrahmen: a b c 4 Drücken und schieben Sie die Freigabelasche auf der Abdeckung nach vorne [1]. Halten Sie die Lasche in der geöffneten Position und heben Sie den Standrahmen nach oben [2].
5 Entfernen Sie die Blende der Systemplatine: a b Entfernen Sie die fünf Schrauben (M3x5), mit denen die Blende der Systemplatine an der Grundplatte der Bildschirmbaugruppe befestigt ist [1]. Heben Sie die Blende der Systemplatine von der Grundplatte der Bildschirmbaugruppe ab [2].
6 Einbauen der Intel Optane-Karte: a b c 10 Bauen Sie die Wärmefalle an der markierten Stelle auf der Systemplatine ein [1]. Setzen Sie die Intel Optane-Karte in den Kartensteckplatz auf der Systemplatine ein [2]. Bringen Sie die Schraube (M2) wieder an, mit der die Intel Optane-Karte an der Systemplatine befestigt wird [3].
7 Anbringen der Blende der Systemplatine: a b Platzieren Sie die Blende der Systemplatine auf der Systemplatine. Richten Sie die Schlitze der Blende der Systemplatine an den Schlitzen auf der Grundplatte der Bildschirmbaugruppe aus [1].
8 Anbringen der hinteren Abdeckung: a b c 12 Platzieren Sie die hintere Abdeckung auf dem System. Drücken und halten Sie die Lasche [1] und richten Sie die Kerben auf der hinteren Abdeckung an den Schlitzen auf dem mittleren Rahmen aus. Schieben Sie die hintere Abdeckung in die dargestellte Richtung, um die Lasche der hinteren Abdeckung unter dem Riegel auf der Blende der Systemplatine zu verriegeln [2].
9 Anbringen des Standrahmens: a b Richten Sie die Laschen am Standrahmen aus [1]. Rasten Sie den Standrahmen auf der hinteren Abdeckung ein [2].
10 Folgen Sie den Anweisungen unter Nach der Arbeit an Komponenten im Inneren des Computers.
3 Wie Sie Hilfe bekommen Kontaktaufnahme mit Dell ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit. Da die Verfügbarkeit dieser Optionen je nach Land und Produkt variiert, stehen einige Services in Ihrer Region möglicherweise nicht zur Verfügung.